From: maxim.osipov@gmail.com (Maxim Osipov)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v3] AT91: Add flexibity board support
Date: Tue, 14 Sep 2010 11:58:19 +0400 [thread overview]
Message-ID: <4C8F2B1B.7090003@gmail.com> (raw)
Hello,
Please find updated flexibity board support patch below.
Kind regards,
Maxim
WARNING: multiple messages have this Message-ID (diff)
From: Maxim Osipov <maxim.osipov@gmail.com>
To: Russell King <linux@arm.linux.org.uk>,
Andrew Victor <linux@maxim.org.za>,
Nicolas Ferre <nicolas.ferre@atmel.com>,
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>,
"Antonio R. Costa" <costa.antonior@gmail.com>,
Ernst Schwab <eschwab@online.de>,
Andrew Morton <akpm@linux-foundation.org>,
Maxim Osipov <maxim.osipov@gmail.com>,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: [PATCH v3] AT91: Add flexibity board support
Date: Tue, 14 Sep 2010 11:58:19 +0400 [thread overview]
Message-ID: <4C8F2B1B.7090003@gmail.com> (raw)
Hello,
Please find updated flexibity board support patch below.
Kind regards,
Maxim
>From 1fe2aaae2574a4eabda2547ecad0bd0085e3ca3e Mon Sep 17 00:00:00 2001
From: Maxim Osipov <maxim.osipov@gmail.com>
Date: Sun, 12 Sep 2010 16:23:48 +0400
Subject: [PATCH] AT91: Add flexibity board support
Signed-off-by: Maxim Osipov <maxim.osipov@gmail.com>
---
arch/arm/mach-at91/Kconfig | 6 ++
arch/arm/mach-at91/Makefile | 1 +
arch/arm/mach-at91/board-flexibity.c | 164 ++++++++++++++++++++++++++++++++++
3 files changed, 171 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-at91/board-flexibity.c
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 939bccd..ca33862 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -248,6 +248,12 @@ config MACH_CPU9260
Select this if you are using a Eukrea Electromatique's
CPU9260 Board <http://www.eukrea.com/>
+config MACH_FLEXIBITY
+ bool "Flexibity Connect board"
+ help
+ Select this if you are using Flexibity Connect board
+ <http://www.flexibity.com>
+
endif
# ----------------------------------------------------------
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index ca2ac00..7cbe06d 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -46,6 +46,7 @@ obj-$(CONFIG_MACH_USB_A9260) += board-usb-a9260.o
obj-$(CONFIG_MACH_QIL_A9260) += board-qil-a9260.o
obj-$(CONFIG_MACH_AFEB9260) += board-afeb-9260v1.o
obj-$(CONFIG_MACH_CPU9260) += board-cpu9krea.o
+obj-$(CONFIG_MACH_FLEXIBITY) += board-flexibity.o
# AT91SAM9261 board-specific support
obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o
diff --git a/arch/arm/mach-at91/board-flexibity.c b/arch/arm/mach-at91/board-flexibity.c
new file mode 100644
index 0000000..216c8ca
--- /dev/null
+++ b/arch/arm/mach-at91/board-flexibity.c
@@ -0,0 +1,164 @@
+/*
+ * linux/arch/arm/mach-at91/board-flexibity.c
+ *
+ * Copyright (C) 2010 Flexibity
+ * Copyright (C) 2005 SAN People
+ * Copyright (C) 2006 Atmel
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/input.h>
+#include <linux/gpio.h>
+
+#include <asm/mach-types.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/board.h>
+
+#include "generic.h"
+
+static void __init flexibity_map_io(void)
+{
+ /* Initialize processor: 18.432 MHz crystal */
+ at91sam9260_initialize(18432000);
+
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
+}
+
+static void __init flexibity_init_irq(void)
+{
+ at91sam9260_init_interrupts(NULL);
+}
+
+/* USB Host port */
+static struct at91_usbh_data __initdata flexibity_usbh_data = {
+ .ports = 2,
+};
+
+/* USB Device port */
+static struct at91_udc_data __initdata flexibity_udc_data = {
+ .vbus_pin = AT91_PIN_PC5,
+ .pullup_pin = 0, /* pull-up driven by UDC */
+};
+
+/* SPI devices */
+static struct spi_board_info flexibity_spi_devices[] = {
+ { /* DataFlash chip */
+ .modalias = "mtd_dataflash",
+ .chip_select = 1,
+ .max_speed_hz = 15 * 1000 * 1000,
+ .bus_num = 0,
+ },
+};
+
+/* MCI (SD/MMC) */
+static struct at91_mmc_data __initdata flexibity_mmc_data = {
+ .slot_b = 0,
+ .wire4 = 1,
+ .det_pin = AT91_PIN_PC9,
+ .wp_pin = AT91_PIN_PC4,
+};
+
+/* LEDs */
+static struct gpio_led flexibity_leds[] = {
+ {
+ .name = "usb1:green",
+ .gpio = AT91_PIN_PA12,
+ .active_low = 1,
+ .default_trigger = "default-on",
+ },
+ {
+ .name = "usb1:red",
+ .gpio = AT91_PIN_PA13,
+ .active_low = 1,
+ .default_trigger = "default-on",
+ },
+ {
+ .name = "usb2:green",
+ .gpio = AT91_PIN_PB26,
+ .active_low = 1,
+ .default_trigger = "default-on",
+ },
+ {
+ .name = "usb2:red",
+ .gpio = AT91_PIN_PB27,
+ .active_low = 1,
+ .default_trigger = "default-on",
+ },
+ {
+ .name = "usb3:green",
+ .gpio = AT91_PIN_PC8,
+ .active_low = 1,
+ .default_trigger = "default-on",
+ },
+ {
+ .name = "usb3:red",
+ .gpio = AT91_PIN_PC6,
+ .active_low = 1,
+ .default_trigger = "default-on",
+ },
+ {
+ .name = "usb4:green",
+ .gpio = AT91_PIN_PB4,
+ .active_low = 1,
+ .default_trigger = "default-on",
+ },
+ {
+ .name = "usb4:red",
+ .gpio = AT91_PIN_PB5,
+ .active_low = 1,
+ .default_trigger = "default-on",
+ }
+};
+
+static void __init flexibity_board_init(void)
+{
+ /* Serial */
+ at91_add_device_serial();
+ /* USB Host */
+ at91_add_device_usbh(&flexibity_usbh_data);
+ /* USB Device */
+ at91_add_device_udc(&flexibity_udc_data);
+ /* SPI */
+ at91_add_device_spi(flexibity_spi_devices,
+ ARRAY_SIZE(flexibity_spi_devices));
+ /* MMC */
+ at91_add_device_mmc(0, &flexibity_mmc_data);
+ /* LEDs */
+ at91_gpio_leds(flexibity_leds, ARRAY_SIZE(flexibity_leds));
+}
+
+MACHINE_START(FLEXIBITY, "Flexibity Connect")
+ /* Maintainer: Maxim Osipov */
+ .phys_io = AT91_BASE_SYS,
+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+ .boot_params = AT91_SDRAM_BASE + 0x100,
+ .timer = &at91sam926x_timer,
+ .map_io = flexibity_map_io,
+ .init_irq = flexibity_init_irq,
+ .init_machine = flexibity_board_init,
+MACHINE_END
--
1.7.1
next reply other threads:[~2010-09-14 7:58 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-09-14 7:58 Maxim Osipov [this message]
2010-09-14 7:58 ` [PATCH v3] AT91: Add flexibity board support Maxim Osipov
2010-09-18 1:09 ` Jean-Christophe PLAGNIOL-VILLARD
2010-09-18 1:09 ` Jean-Christophe PLAGNIOL-VILLARD
2010-09-20 16:40 ` Jean-Christophe PLAGNIOL-VILLARD
2010-09-20 16:40 ` Jean-Christophe PLAGNIOL-VILLARD
2010-09-21 6:42 ` avictor.za at gmail.com
2010-09-21 6:42 ` avictor.za
2010-09-21 6:48 ` Maxim Osipov
2010-09-21 6:48 ` Maxim Osipov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4C8F2B1B.7090003@gmail.com \
--to=maxim.osipov@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.