* [PATCH V6 13/63] ST SPEAr: Updating Clock Support
[not found] <cover.1297763160.git.viresh.kumar@st.com>
@ 2011-02-15 9:47 ` Viresh Kumar
2011-02-16 1:40 ` stanley.miao
0 siblings, 1 reply; 2+ messages in thread
From: Viresh Kumar @ 2011-02-15 9:47 UTC (permalink / raw)
To: linux-arm-kernel
- Adding support for divisor per parent clock
- Adding ENABLED_ON_INIT feature in clk
- Adding clk_set_rate, round_rate_index & clk_round_rate
- Simplified clk_recalc functions
- Added/updating clock definitions
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: shiraz hashim <shiraz.hashim@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
---
arch/arm/mach-spear13xx/clock.c | 621 ++++++++++++++++++-
arch/arm/mach-spear13xx/include/mach/misc_regs.h | 101 ++--
arch/arm/mach-spear3xx/clock.c | 431 +++++++++++--
arch/arm/mach-spear3xx/include/mach/misc_regs.h | 5 +-
arch/arm/mach-spear6xx/clock.c | 331 ++++++++---
arch/arm/mach-spear6xx/include/mach/misc_regs.h | 5 +-
arch/arm/plat-spear/clock.c | 705 +++++++++++++++++-----
arch/arm/plat-spear/include/plat/clock.h | 94 +++-
8 files changed, 1918 insertions(+), 375 deletions(-)
diff --git a/arch/arm/mach-spear13xx/clock.c b/arch/arm/mach-spear13xx/clock.c
index 722f634..c39389e 100644
--- a/arch/arm/mach-spear13xx/clock.c
+++ b/arch/arm/mach-spear13xx/clock.c
@@ -53,10 +53,10 @@ static struct clk rtc_clk = {
static struct pclk_info pll_pclk_info[] = {
{
.pclk = &osc1_24m_clk,
- .pclk_mask = OSC_24M_MASK,
+ .pclk_val = OSC_24M_VAL,
}, {
.pclk = &osc3_25m_clk,
- .pclk_mask = OSC_25M_MASK,
+ .pclk_val = OSC_25M_VAL,
},
};
@@ -88,16 +88,45 @@ static struct pll_clk_config pll1_config = {
.masks = &pll_masks,
};
+/* pll rate configuration table, in ascending order of rates */
+struct pll_rate_tbl pll_rtbl[] = {
+ /* PCLK 24MHz */
+ {.mode = 0, .m = 0x7D, .n = 0x03, .p = 0x2}, /* 500 MHz */
+ {.mode = 0, .m = 0xA6, .n = 0x03, .p = 0x2}, /* 664 MHz */
+ {.mode = 0, .m = 0xC8, .n = 0x03, .p = 0x2}, /* 800 MHz */
+ {.mode = 0, .m = 0xFA, .n = 0x06, .p = 0x1}, /* 1000 MHz */
+};
+
/* pll1 clock */
static struct clk pll1_clk = {
+ .flags = ENABLED_ON_INIT,
.pclk_sel = &pll_pclk_sel,
.pclk_sel_shift = PLL1_CLK_SHIFT,
.en_reg = PLL1_CTR,
.en_reg_bit = PLL_ENABLE,
+ .calc_rate = &pll_calc_rate,
.recalc = &pll_clk_recalc,
+ .set_rate = &pll_clk_set_rate,
+ .rate_config = {pll_rtbl, ARRAY_SIZE(pll_rtbl), 3},
.private_data = &pll1_config,
};
+/* pll1div2 clock */
+static struct clk pll1div2_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &pll1_clk,
+ .div_factor = 2,
+ .recalc = &follow_parent,
+};
+
+/* pll1div4 clock */
+static struct clk pll1div4_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &pll1_clk,
+ .div_factor = 4,
+ .recalc = &follow_parent,
+};
+
/* pll2 configuration structure */
static struct pll_clk_config pll2_config = {
.mode_reg = PLL2_CTR,
@@ -111,7 +140,10 @@ static struct clk pll2_clk = {
.pclk_sel_shift = PLL2_CLK_SHIFT,
.en_reg = PLL2_CTR,
.en_reg_bit = PLL_ENABLE,
+ .calc_rate = &pll_calc_rate,
.recalc = &pll_clk_recalc,
+ .set_rate = &pll_clk_set_rate,
+ .rate_config = {pll_rtbl, ARRAY_SIZE(pll_rtbl), 3},
.private_data = &pll2_config,
};
@@ -128,7 +160,10 @@ static struct clk pll3_clk = {
.pclk_sel_shift = PLL3_CLK_SHIFT,
.en_reg = PLL3_CTR,
.en_reg_bit = PLL_ENABLE,
+ .calc_rate = &pll_calc_rate,
.recalc = &pll_clk_recalc,
+ .set_rate = &pll_clk_set_rate,
+ .rate_config = {pll_rtbl, ARRAY_SIZE(pll_rtbl), 3},
.private_data = &pll3_config,
};
@@ -139,12 +174,24 @@ static struct pll_clk_config pll4_config = {
.masks = &pll_masks,
};
+/* pll4 rate configuration table, in ascending order of rates */
+struct pll_rate_tbl pll4_rtbl[] = {
+ {.mode = 0, .m = 0x7D, .n = 0x03, .p = 0x2}, /* 500 MHz */
+ {.mode = 0, .m = 0xA6, .n = 0x03, .p = 0x2}, /* 664 MHz */
+ {.mode = 0, .m = 0xC8, .n = 0x03, .p = 0x2}, /* 800 MHz */
+ {.mode = 0, .m = 0xFA, .n = 0x06, .p = 0x1}, /* 1000 MHz */
+};
+
/* pll4 (DDR) clock */
static struct clk pll4_clk = {
+ .flags = ENABLED_ON_INIT,
.pclk = &osc1_24m_clk,
.en_reg = PLL4_CTR,
.en_reg_bit = PLL_ENABLE,
+ .calc_rate = &pll_calc_rate,
.recalc = &pll_clk_recalc,
+ .set_rate = &pll_clk_set_rate,
+ .rate_config = {pll4_rtbl, ARRAY_SIZE(pll4_rtbl), 3},
.private_data = &pll4_config,
};
@@ -192,10 +239,10 @@ static struct clk apb_clk = {
static struct pclk_info gpt_pclk_info[] = {
{
.pclk = &osc1_24m_clk,
- .pclk_mask = GPT_OSC24_MASK,
+ .pclk_val = GPT_OSC24_VAL,
}, {
.pclk = &apb_clk,
- .pclk_mask = GPT_APB_MASK,
+ .pclk_val = GPT_APB_VAL,
},
};
@@ -246,15 +293,8 @@ static struct clk gpt3_clk = {
/* watch dog timer clock */
static struct clk wdt_clk = {
.flags = ALWAYS_ENABLED,
- .pclk = &apb_clk,
- .recalc = &follow_parent,
-};
-
-/* smi clock */
-static struct clk smi_clk = {
- .pclk = &ahb_clk,
- .en_reg = PERIP1_CLK_ENB,
- .en_reg_bit = SMI_CLK_ENB,
+ .pclk = &cpu_clk,
+ .div_factor = 2,
.recalc = &follow_parent,
};
@@ -270,22 +310,42 @@ static struct aux_clk_masks aux_masks = {
.yscale_sel_shift = AUX_YSCALE_SHIFT,
};
+/* clocks derived multiple parents (pll1, pll5, synthesizers or others) */
/* uart configurations */
-static struct aux_clk_config uart_config = {
+static struct aux_clk_config uart_synth_config = {
.synth_reg = UART_CLK_SYNT,
.masks = &aux_masks,
};
-/* clocks derived from pll1 or pll5 */
+/* aux rate configuration table, in ascending order of rates */
+struct aux_rate_tbl aux_rtbl[] = {
+ /* For PLL1div2 = 500 MHz */
+ {.xscale = 1, .yscale = 6, .eq = 1}, /* 83 MHz */
+ {.xscale = 1, .yscale = 4, .eq = 1}, /* 125 MHz */
+ {.xscale = 1, .yscale = 3, .eq = 1}, /* 166 MHz */
+ {.xscale = 1, .yscale = 2, .eq = 1}, /* 250 MHz */
+};
+
+/* uart synth clock */
+static struct clk uart_synth_clk = {
+ .en_reg = UART_CLK_SYNT,
+ .en_reg_bit = AUX_SYNT_ENB,
+ .pclk = &pll1div2_clk,
+ .calc_rate = &aux_calc_rate,
+ .recalc = &aux_clk_recalc,
+ .set_rate = &aux_clk_set_rate,
+ .rate_config = {aux_rtbl, ARRAY_SIZE(aux_rtbl), 0},
+ .private_data = &uart_synth_config,
+};
+
/* uart parents */
static struct pclk_info uart_pclk_info[] = {
{
.pclk = &pll5_clk,
- .pclk_mask = AUX_CLK_PLL5_MASK,
+ .pclk_val = AUX_CLK_PLL5_VAL,
}, {
- .pclk = &pll1_clk,
- .pclk_mask = AUX_CLK_PLL1_MASK,
- .scalable = 1,
+ .pclk = &uart_synth_clk,
+ .pclk_val = AUX_CLK_SYNT_VAL,
},
};
@@ -303,10 +363,469 @@ static struct clk uart_clk = {
.en_reg_bit = UART_CLK_ENB,
.pclk_sel = &uart_pclk_sel,
.pclk_sel_shift = UART_CLK_SHIFT,
+ .recalc = &follow_parent,
+};
+
+/* sdhci configurations */
+static struct aux_clk_config sdhci_synth_config = {
+ .synth_reg = SDHCI_CLK_SYNT,
+ .masks = &aux_masks,
+};
+
+/* sdhci synth clock */
+static struct clk sdhci_synth_clk = {
+ .en_reg = SDHCI_CLK_SYNT,
+ .en_reg_bit = AUX_SYNT_ENB,
+ .pclk = &pll1div2_clk,
+ .calc_rate = &aux_calc_rate,
+ .recalc = &aux_clk_recalc,
+ .set_rate = &aux_clk_set_rate,
+ .rate_config = {aux_rtbl, ARRAY_SIZE(aux_rtbl), 2},
+ .private_data = &sdhci_synth_config,
+};
+
+/* sdhci clock */
+static struct clk sdhci_clk = {
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = SDHCI_CLK_ENB,
+ .pclk = &sdhci_synth_clk,
+ .recalc = &follow_parent,
+};
+
+/* cfxd configurations */
+static struct aux_clk_config cfxd_synth_config = {
+ .synth_reg = CFXD_CLK_SYNT,
+ .masks = &aux_masks,
+};
+
+/* cfxd synth clock */
+static struct clk cfxd_synth_clk = {
+ .en_reg = CFXD_CLK_SYNT,
+ .en_reg_bit = AUX_SYNT_ENB,
+ .pclk = &pll1div2_clk,
+ .calc_rate = &aux_calc_rate,
+ .recalc = &aux_clk_recalc,
+ .set_rate = &aux_clk_set_rate,
+ .rate_config = {aux_rtbl, ARRAY_SIZE(aux_rtbl), 2},
+ .private_data = &cfxd_synth_config,
+};
+
+/* cfxd clock */
+static struct clk cfxd_clk = {
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = CFXD_CLK_ENB,
+ .pclk = &cfxd_synth_clk,
+ .recalc = &follow_parent,
+};
+
+/* C3 clk configurations */
+static struct aux_clk_config c3_synth_config = {
+ .synth_reg = C3_CLK_SYNT,
+ .masks = &aux_masks,
+};
+
+/* c3 synth clock */
+static struct clk c3_synth_clk = {
+ .en_reg = C3_CLK_SYNT,
+ .en_reg_bit = AUX_SYNT_ENB,
+ .pclk = &pll1div2_clk,
+ .calc_rate = &aux_calc_rate,
+ .recalc = &aux_clk_recalc,
+ .set_rate = &aux_clk_set_rate,
+ .rate_config = {aux_rtbl, ARRAY_SIZE(aux_rtbl), 0},
+ .private_data = &c3_synth_config,
+};
+
+/* c3 parents */
+static struct pclk_info c3_pclk_info[] = {
+ {
+ .pclk = &pll5_clk,
+ .pclk_val = AUX_CLK_PLL5_VAL,
+ }, {
+ .pclk = &c3_synth_clk,
+ .pclk_val = AUX_CLK_SYNT_VAL,
+ },
+};
+
+/* c3 parent select structure */
+static struct pclk_sel c3_pclk_sel = {
+ .pclk_info = c3_pclk_info,
+ .pclk_count = ARRAY_SIZE(c3_pclk_info),
+ .pclk_sel_reg = PERIP_CLK_CFG,
+ .pclk_sel_mask = C3_CLK_MASK,
+};
+
+/* c3 clock */
+static struct clk c3_clk = {
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = C3_CLK_ENB,
+ .pclk_sel = &c3_pclk_sel,
+ .pclk_sel_shift = C3_CLK_SHIFT,
+ .recalc = &follow_parent,
+};
+
+/* gmac phy clk configurations */
+static struct aux_clk_config gmac_phy_synth_config = {
+ .synth_reg = GMAC_CLK_SYNT,
+ .masks = &aux_masks,
+};
+
+/* gmii external pad clock for phy operation */
+static struct clk gmii_txclk125_pad = {
+ .flags = ALWAYS_ENABLED,
+ .rate = 125000000,
+};
+
+/* gmac phy set of input clks*/
+static struct pclk_info gmac_phy_input_pclk_info[] = {
+ {
+ .pclk = &gmii_txclk125_pad,
+ .pclk_val = GMAC_PHY_PAD_VAL,
+ }, {
+ .pclk = &pll2_clk,
+ .pclk_val = GMAC_PHY_PLL2_VAL,
+ }, {
+ .pclk = &osc3_25m_clk,
+ .pclk_val = GMAC_PHY_OSC3_VAL,
+ },
+};
+
+static struct pclk_sel gmac_phy_input_pclk_sel = {
+ .pclk_info = gmac_phy_input_pclk_info,
+ .pclk_count = ARRAY_SIZE(gmac_phy_input_pclk_info),
+ .pclk_sel_reg = GMAC_CLK_CFG,
+ .pclk_sel_mask = GMAC_PHY_INPUT_CLK_MASK,
+};
+
+static struct clk gmac_phy_input_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk_sel = &gmac_phy_input_pclk_sel,
+ .pclk_sel_shift = GMAC_PHY_INPUT_CLK_SHIFT,
+ .recalc = &follow_parent,
+};
+
+/* gmac rate configuration table, in ascending order of rates */
+struct aux_rate_tbl gmac_rtbl[] = {
+ /* For gmac phy input clk */
+ {.xscale = 1, .yscale = 6, .eq = 1}, /* divided by 6 */
+ {.xscale = 1, .yscale = 4, .eq = 1}, /* divided by 4 */
+ {.xscale = 1, .yscale = 3, .eq = 1}, /* divided by 3 */
+ {.xscale = 1, .yscale = 2, .eq = 1}, /* divided by 2 */
+};
+
+static struct clk gmac_phy_synth_clk = {
+ .en_reg = GMAC_CLK_CFG,
+ .en_reg_bit = GMAC_PHY_SYNT_ENB,
+ .pclk = &gmac_phy_input_clk,
+ .calc_rate = &aux_calc_rate,
.recalc = &aux_clk_recalc,
- .private_data = &uart_config,
+ .set_rate = &aux_clk_set_rate,
+ .rate_config = {gmac_rtbl, ARRAY_SIZE(gmac_rtbl), 0},
+ .private_data = &gmac_phy_synth_config,
+};
+
+/* gmac phy parents */
+static struct pclk_info gmac_phy_pclk_info[] = {
+ {
+ .pclk = &gmac_phy_input_clk,
+ .pclk_val = 0,
+ }, {
+ .pclk = &gmac_phy_synth_clk,
+ .pclk_val = 1,
+ }
+};
+
+/* gmac phy parent select structure */
+static struct pclk_sel gmac_phy_pclk_sel = {
+ .pclk_info = gmac_phy_pclk_info,
+ .pclk_count = ARRAY_SIZE(gmac_phy_pclk_info),
+ .pclk_sel_reg = GMAC_CLK_CFG,
+ .pclk_sel_mask = GMAC_PHY_CLK_MASK,
+};
+
+/* gmac phy clock */
+static struct clk gmac_phy_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk_sel = &gmac_phy_pclk_sel,
+ .pclk_sel_shift = GMAC_PHY_CLK_SHIFT,
+ .recalc = &follow_parent,
+};
+
+/* clcd synthesizers masks */
+static struct clcd_synth_masks clcd_masks = {
+ .div_factor_mask = CLCD_SYNT_DIV_FACTOR_MASK,
+ .div_factor_shift = CLCD_SYNT_DIV_FACTOR_SHIFT,
+};
+
+static struct clcd_clk_config clcd_synth_config = {
+ .synth_reg = CLCD_CLK_SYNT,
+ .masks = &clcd_masks,
+};
+
+/* clcd synth parents */
+static struct pclk_info clcd_synth_pclk_info[] = {
+ {
+ .pclk = &pll1div4_clk,
+ .pclk_val = CLCD_SYNT_PLL1_DIV4_VAL,
+ }, {
+ .pclk = &pll2_clk,
+ .pclk_val = CLCD_SYNT_PLL2_VAL,
+ },
+};
+
+/* clcd synth parent select structure */
+static struct pclk_sel clcd_synth_pclk_sel = {
+ .pclk_info = clcd_synth_pclk_info,
+ .pclk_count = ARRAY_SIZE(clcd_synth_pclk_info),
+ .pclk_sel_reg = PLL_CFG,
+ .pclk_sel_mask = CLCD_SYNT_CLK_MASK,
+};
+
+/* clcd rate configuration table, in ascending order of rates */
+struct clcd_rate_tbl clcd_rtbl[] = {
+ /* For pll1div4 = 250 MHz */
+ {.div = 0x4000}, /* 62.5 MHz */
+ {.div = 0x2000}, /* 125 MHz */
+};
+
+/* clcd synth clock */
+static struct clk clcd_synth_clk = {
+ .en_reg = CLCD_CLK_SYNT,
+ .en_reg_bit = CLCD_SYNT_ENB,
+ .pclk_sel = &clcd_synth_pclk_sel,
+ .pclk_sel_shift = CLCD_SYNT_CLK_SHIFT,
+ .calc_rate = &clcd_calc_rate,
+ .recalc = &clcd_clk_recalc,
+ .set_rate = &clcd_clk_set_rate,
+ .rate_config = {clcd_rtbl, ARRAY_SIZE(clcd_rtbl), 1},
+ .private_data = &clcd_synth_config,
+};
+
+/* clcd clock parents */
+static struct pclk_info clcd_pclk_info[] = {
+ {
+ .pclk = &pll5_clk,
+ .pclk_val = AUX_CLK_PLL5_VAL,
+ }, {
+ .pclk = &clcd_synth_clk,
+ .pclk_val = AUX_CLK_SYNT_VAL,
+ },
+};
+
+/* clcd parent select structure */
+static struct pclk_sel clcd_pclk_sel = {
+ .pclk_info = clcd_pclk_info,
+ .pclk_count = ARRAY_SIZE(clcd_pclk_info),
+ .pclk_sel_reg = PERIP_CLK_CFG,
+ .pclk_sel_mask = CLCD_CLK_MASK,
+};
+
+/* clcd clock */
+static struct clk clcd_clk = {
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = CLCD_CLK_ENB,
+ .pclk_sel = &clcd_pclk_sel,
+ .pclk_sel_shift = CLCD_CLK_SHIFT,
+ .recalc = &follow_parent,
+};
+
+/* clock derived from ahb clk */
+
+/* i2c clock */
+static struct clk i2c_clk = {
+ .pclk = &ahb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = I2C_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* dma clock */
+static struct clk dma0_clk = {
+ .pclk = &ahb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = DMA0_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+static struct clk dma1_clk = {
+ .pclk = &ahb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = DMA1_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* jpeg clock */
+static struct clk jpeg_clk = {
+ .pclk = &ahb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = JPEG_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* gmac clock */
+static struct clk gmac_clk = {
+ .pclk = &ahb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = GMAC_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* fsmc clock */
+static struct clk fsmc_clk = {
+ .pclk = &ahb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = FSMC_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* smi clock */
+static struct clk smi_clk = {
+ .pclk = &ahb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = SMI_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* uhc0 clock */
+static struct clk uhci0_clk = {
+ .pclk = &ahb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = UHC0_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* uhc1 clock */
+static struct clk uhci1_clk = {
+ .pclk = &ahb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = UHC1_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* usbd clock */
+static struct clk usbd_clk = {
+ .pclk = &ahb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = USBD_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* pci clocks */
+static struct clk pcie0_clk = {
+ .pclk = &ahb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = PCIE0_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+static struct clk pcie1_clk = {
+ .pclk = &ahb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = PCIE1_CLK_ENB,
+ .recalc = &follow_parent,
};
+static struct clk pcie2_clk = {
+ .pclk = &ahb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = PCIE2_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* sysram clocks */
+static struct clk sysram0_clk = {
+ .pclk = &ahb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = SYSRAM0_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+static struct clk sysram1_clk = {
+ .pclk = &ahb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = SYSRAM1_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* clock derived from apb clk */
+/* adc clock */
+static struct clk adc_clk = {
+ .pclk = &apb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = ADC_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* ssp clock */
+static struct clk ssp_clk = {
+ .pclk = &apb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = SSP_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* gpio clock */
+static struct clk gpio0_clk = {
+ .pclk = &apb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = GPIO0_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* gpio clock */
+static struct clk gpio1_clk = {
+ .pclk = &apb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = GPIO1_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* i2s0 clock */
+static struct clk i2s0_clk = {
+ .pclk = &apb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = I2S0_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* i2s1 clock */
+static struct clk i2s1_clk = {
+ .pclk = &apb_clk,
+ .en_reg = PERIP1_CLK_ENB,
+ .en_reg_bit = I2S1_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* keyboard clock */
+static struct clk kbd_clk = {
+ .pclk = &apb_clk,
+ .en_reg = PERIP2_CLK_ENB,
+ .en_reg_bit = KBD_CLK_ENB,
+ .recalc = &follow_parent,
+};
+
+/* spear1300 machine specific clock structures */
+#ifdef CONFIG_MACH_SPEAR1300
+
+#endif
+
+/* spear1310 machine specific clock structures */
+#ifdef CONFIG_MACH_SPEAR1310
+/* can0 clock */
+static struct clk can0_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &apb_clk,
+ .recalc = &follow_parent,
+};
+
+/* can1 clock */
+static struct clk can1_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &apb_clk,
+ .recalc = &follow_parent,
+};
+#endif
+
/* array of all spear 13xx clock lookups */
static struct clk_lookup spear_clk_lookups[] = {
/* root clks */
@@ -315,7 +834,7 @@ static struct clk_lookup spear_clk_lookups[] = {
{.con_id = "osc3_25m_clk", .clk = &osc3_25m_clk},
/* clock derived from 32 KHz osc clk */
- {.dev_id = "rtc", .clk = &rtc_clk},
+ {.dev_id = "rtc-spear", .clk = &rtc_clk},
/* clock derived from 24/25 MHz osc1/osc3 clk */
{.con_id = "pll1_clk", .clk = &pll1_clk},
@@ -328,18 +847,68 @@ static struct clk_lookup spear_clk_lookups[] = {
/* clock derived from pll1 clk */
{.con_id = "cpu_clk", .clk = &cpu_clk},
{.con_id = "ahb_clk", .clk = &ahb_clk},
- { .con_id = "apb_clk", .clk = &apb_clk},
+ {.con_id = "apb_clk", .clk = &apb_clk},
+
+ /* synthesizers/prescaled clocks */
+ {.con_id = "pll1div2_clk", .clk = &pll1div2_clk},
+ {.con_id = "pll1div4_clk", .clk = &pll1div4_clk},
+ {.con_id = "c3_synth_clk", .clk = &c3_synth_clk},
+ {.con_id = "gmii_txclk123_pad_clk", .clk = &gmii_txclk125_pad},
+ {.con_id = "clcd_synth_clk", .clk = &clcd_synth_clk},
+ {.con_id = "uart_synth_clk", .clk = &uart_synth_clk},
+ {.con_id = "sdhci_synth_clk", .clk = &sdhci_synth_clk},
+ {.con_id = "cfxd_synth_clk", .clk = &cfxd_synth_clk},
+ {.con_id = "gmac_phy_input_clk", .clk = &gmac_phy_input_clk},
+ {.con_id = "gmac_phy_synth_clk", .clk = &gmac_phy_synth_clk},
+ {.con_id = "gmac_phy_clk", .clk = &gmac_phy_clk},
/* clocks having multiple parent source from above clocks */
- {.dev_id = "uart", .clk = &uart_clk},
+ {.dev_id = "clcd", .clk = &clcd_clk},
{.dev_id = "gpt0", .clk = &gpt0_clk},
{.dev_id = "gpt1", .clk = &gpt1_clk},
{.dev_id = "gpt2", .clk = &gpt2_clk},
{.dev_id = "gpt3", .clk = &gpt3_clk},
+ {.dev_id = "uart", .clk = &uart_clk},
- /* clock derived from ahb/apb clk */
- { .dev_id = "smi", .clk = &smi_clk},
- { .dev_id = "wdt", .clk = &wdt_clk},
+ /* clock derived from ahb clk */
+ {.dev_id = "smi", .clk = &smi_clk},
+ {.con_id = "usbh.0_clk", .clk = &uhci0_clk},
+ {.con_id = "usbh.1_clk", .clk = &uhci1_clk},
+ {.dev_id = "usbd", .clk = &usbd_clk},
+ {.dev_id = "i2c_designware.0", .clk = &i2c_clk},
+ {.dev_id = "dma0", .clk = &dma0_clk},
+ {.dev_id = "dma1", .clk = &dma1_clk},
+ {.dev_id = "jpeg", .clk = &jpeg_clk},
+ {.dev_id = "gmac", .clk = &gmac_clk},
+ {.dev_id = "c3", .clk = &c3_clk},
+ {.dev_id = "pcie0", .clk = &pcie0_clk},
+ {.dev_id = "pcie1", .clk = &pcie1_clk},
+ {.dev_id = "pcie2", .clk = &pcie2_clk},
+ {.dev_id = "cfxd", .clk = &cfxd_clk},
+ {.dev_id = "sdhci", .clk = &sdhci_clk},
+ {.con_id = "fsmc", .clk = &fsmc_clk},
+ {.dev_id = "sysram0", .clk = &sysram0_clk},
+ {.dev_id = "sysram1", .clk = &sysram1_clk},
+
+ /* clock derived from apb clk */
+ {.dev_id = "i2s0", .clk = &i2s0_clk},
+ {.dev_id = "i2s1", .clk = &i2s1_clk},
+ {.dev_id = "adc", .clk = &adc_clk},
+ {.dev_id = "ssp-pl022", .clk = &ssp_clk},
+ {.dev_id = "gpio0", .clk = &gpio0_clk},
+ {.dev_id = "gpio1", .clk = &gpio1_clk},
+ {.dev_id = "keyboard", .clk = &kbd_clk},
+ {.dev_id = "wdt", .clk = &wdt_clk},
+
+ /* spear1300 machine specific clock structures */
+#ifdef CONFIG_MACH_SPEAR1300
+#endif
+
+ /* spear1310 machine specific clock structures */
+#ifdef CONFIG_MACH_SPEAR1310
+ {.dev_id = "c_can_platform.0", .clk = &can0_clk},
+ {.dev_id = "c_can_platform.1", .clk = &can1_clk},
+#endif
};
void __init clk_init(void)
diff --git a/arch/arm/mach-spear13xx/include/mach/misc_regs.h b/arch/arm/mach-spear13xx/include/mach/misc_regs.h
index 56ffa4e..0a9c86a 100644
--- a/arch/arm/mach-spear13xx/include/mach/misc_regs.h
+++ b/arch/arm/mach-spear13xx/include/mach/misc_regs.h
@@ -36,12 +36,16 @@
/* PLL related registers and bit values */
#define PLL_CFG (MISC_BASE + 0x210)
/* PLL_CFG bit values */
- #define OSC_24M_MASK 0
- #define OSC_25M_MASK 1
- #define PLL_CLK_MASK 3
- #define PLL1_CLK_SHIFT 20
- #define PLL2_CLK_SHIFT 22
- #define PLL3_CLK_SHIFT 24
+ #define OSC_24M_VAL 0
+ #define OSC_25M_VAL 1
+ #define PLL_CLK_MASK 3
+ #define PLL1_CLK_SHIFT 20
+ #define PLL2_CLK_SHIFT 22
+ #define PLL3_CLK_SHIFT 24
+ #define CLCD_SYNT_PLL1_DIV4_VAL 0
+ #define CLCD_SYNT_PLL2_VAL 1
+ #define CLCD_SYNT_CLK_MASK 1
+ #define CLCD_SYNT_CLK_SHIFT 31
#define PLL1_CTR (MISC_BASE + 0x214)
#define PLL1_FRQ (MISC_BASE + 0x218)
@@ -77,30 +81,53 @@
#define PERIP_CLK_CFG (MISC_BASE + 0x244)
/* PERIP_CLK_CFG bit values */
- #define GPT_OSC24_MASK 0
- #define GPT_APB_MASK 1
- #define GPT_CLK_MASK 1
- #define GPT0_CLK_SHIFT 8
- #define GPT1_CLK_SHIFT 9
- #define GPT2_CLK_SHIFT 12
- #define GPT3_CLK_SHIFT 13
- #define AUX_CLK_PLL1_MASK 1
- #define AUX_CLK_PLL5_MASK 0
+ #define GPT_OSC24_VAL 0
+ #define GPT_APB_VAL 1
+ #define GPT_CLK_MASK 1
+ #define GPT0_CLK_SHIFT 8
+ #define GPT1_CLK_SHIFT 9
+ #define GPT2_CLK_SHIFT 12
+ #define GPT3_CLK_SHIFT 13
+ #define AUX_CLK_PLL5_VAL 0
+ #define AUX_CLK_SYNT_VAL 1
#define UART_CLK_MASK 1
#define UART_CLK_SHIFT 4
+ #define CLCD_PLL5_VAL 0
+ #define CLCD_SYNT_MASK 1
+ #define CLCD_CLK_MASK 3
+ #define CLCD_CLK_SHIFT 2
+ #define C3_CLK_MASK 1
+ #define C3_CLK_SHIFT 1
#define GMAC_CLK_CFG (MISC_BASE + 0x248)
-#define C3_CLK_SYNTH (MISC_BASE + 0x24c)
+
+ #define GMAC_PHY_PAD_VAL 0
+ #define GMAC_PHY_PLL2_VAL 1
+ #define GMAC_PHY_OSC3_VAL 2
+ #define GMAC_PHY_INPUT_CLK_MASK 3
+ #define GMAC_PHY_INPUT_CLK_SHIFT 1
+ #define GMAC_PHY_SYNT_ENB 3
+ #define GMAC_PHY_CLK_MASK 1
+ #define GMAC_PHY_CLK_SHIFT 3
+ #define GMAC_PHY_SYNT_ENB_VAL 4
+
+#define C3_CLK_SYNT (MISC_BASE + 0x24c)
#define CLCD_CLK_SYNT (MISC_BASE + 0x250)
+ /* CLCD synth reg masks */
+ #define CLCD_SYNT_ENB 31
+ #define CLCD_SYNT_DIV_FACTOR_MASK 0x1ffff
+ #define CLCD_SYNT_DIV_FACTOR_SHIFT 0
+
#define UART_CLK_SYNT (MISC_BASE + 0x254)
#define GMAC_CLK_SYNT (MISC_BASE + 0x258)
-#define MCIF_SD_CLK_SYNT (MISC_BASE + 0x25c)
-#define MCIF_CFXD_CLK_SYNT (MISC_BASE + 0x260)
+#define SDHCI_CLK_SYNT (MISC_BASE + 0x25c)
+#define CFXD_CLK_SYNT (MISC_BASE + 0x260)
#define RAS_CLK_SYNT0 (MISC_BASE + 0x264)
#define RAS_CLK_SYNT1 (MISC_BASE + 0x268)
#define RAS_CLK_SYNT2 (MISC_BASE + 0x26c)
#define RAS_CLK_SYNT3 (MISC_BASE + 0x270)
/* aux clk synthesizer register masks */
+ #define AUX_SYNT_ENB 31
#define AUX_EQ_SEL_SHIFT 30
#define AUX_EQ_SEL_MASK 1
#define AUX_EQ1_SEL 0
@@ -114,32 +141,32 @@
/* PERIP1_CLK_ENB register masks */
#define BUS_CLK_ENB 0
#define SYSROM_CLK_ENB 1
- #define AORAM_CLK_ENB 2
- #define SYSRAM_CLK_ENB 3
+ #define SYSRAM1_CLK_ENB 2
+ #define SYSRAM0_CLK_ENB 3
#define FSMC_CLK_ENB 4
#define SMI_CLK_ENB 5
- #define SD_CLK_ENB 6
- #define CF_XD_CLK_ENB 7
- #define GETH_CLK_ENB 8
+ #define SDHCI_CLK_ENB 6
+ #define CFXD_CLK_ENB 7
+ #define GMAC_CLK_ENB 8
#define UHC0_CLK_ENB 9
#define UHC1_CLK_ENB 10
- #define UDC_UPD_CLK_ENB 11
- #define PCI0_CLK_ENB 12
- #define PCI1_CLK_ENB 13
- #define PCI2_CLK_ENB 14
+ #define USBD_CLK_ENB 11
+ #define PCIE0_CLK_ENB 12
+ #define PCIE1_CLK_ENB 13
+ #define PCIE2_CLK_ENB 14
#define UART_CLK_ENB 15
#define SSP_CLK_ENB 17
#define I2C_CLK_ENB 18
- #define I2S_SLV_CLK_ENB 19
- #define I2S_MST_CLK_ENB 20
+ #define I2S0_CLK_ENB 19
+ #define I2S1_CLK_ENB 20
#define GPT0_CLK_ENB 21
#define GPT1_CLK_ENB 22
- #define GPIOA_CLK_ENB 23
- #define GPIOB_CLK_ENB 24
+ #define GPIO0_CLK_ENB 23
+ #define GPIO1_CLK_ENB 24
#define DMA0_CLK_ENB 25
#define DMA1_CLK_ENB 26
#define CLCD_CLK_ENB 27
- #define JPEGC_CLK_ENB 28
+ #define JPEG_CLK_ENB 28
#define C3_CLK_ENB 29
#define ADC_CLK_ENB 30
#define RTC_CLK_ENB 31
@@ -219,11 +246,11 @@
#define THSENS_CFG (MISC_BASE + 0x6c4)
/* Compensation Configuration Registers */
-#define COMP_1V8_2V5_3V3__1_CFG (MISC_BASE + 0x700)
-#define COMP_1V8_2V5_3V3__2_CFG (MISC_BASE + 0x704)
-#define COMP_3V3_1_CFG (MISC_BASE + 0x708)
-#define COMP_3V3_2_CFG (MISC_BASE + 0x70c)
-#define COMP_DDR_CFG (MISC_BASE + 0x710)
+#define COMP_1V8_2V5_3V3__1_CFG (MISC_BASE + 0x700)
+#define COMP_1V8_2V5_3V3__2_CFG (MISC_BASE + 0x704)
+#define COMP_3V3_1_CFG (MISC_BASE + 0x708)
+#define COMP_3V3_2_CFG (MISC_BASE + 0x70c)
+#define COMP_DDR_CFG (MISC_BASE + 0x710)
/* OTP Programming Registers */
#define OTP_PROG_CTR (MISC_BASE + 0x800)
diff --git a/arch/arm/mach-spear3xx/clock.c b/arch/arm/mach-spear3xx/clock.c
index 7ea8749..8ae4ad0 100644
--- a/arch/arm/mach-spear3xx/clock.c
+++ b/arch/arm/mach-spear3xx/clock.c
@@ -60,12 +60,22 @@ static struct pll_clk_config pll1_config = {
.masks = &pll1_masks,
};
+/* pll rate configuration table, in ascending order of rates */
+struct pll_rate_tbl pll_rtbl[] = {
+ {.mode = 0, .m = 0x85, .n = 0x0C, .p = 0x1}, /* 266 MHz */
+ {.mode = 0, .m = 0xA6, .n = 0x0C, .p = 0x1}, /* 332 MHz */
+};
+
/* PLL1 clock */
static struct clk pll1_clk = {
+ .flags = ENABLED_ON_INIT,
.pclk = &osc_24m_clk,
.en_reg = PLL1_CTR,
.en_reg_bit = PLL_ENABLE,
+ .calc_rate = &pll_calc_rate,
.recalc = &pll_clk_recalc,
+ .set_rate = &pll_clk_set_rate,
+ .rate_config = {pll_rtbl, ARRAY_SIZE(pll_rtbl), 1},
.private_data = &pll1_config,
};
@@ -103,11 +113,22 @@ static struct bus_clk_config ahb_config = {
.masks = &ahb_masks,
};
+/* ahb rate configuration table, in ascending order of rates */
+struct bus_rate_tbl bus_rtbl[] = {
+ {.div = 3}, /* == parent divided by 4 */
+ {.div = 2}, /* == parent divided by 3 */
+ {.div = 1}, /* == parent divided by 2 */
+ {.div = 0}, /* == parent divided by 1 */
+};
+
/* ahb clock */
static struct clk ahb_clk = {
.flags = ALWAYS_ENABLED,
.pclk = &pll1_clk,
+ .calc_rate = &bus_calc_rate,
.recalc = &bus_clk_recalc,
+ .set_rate = &bus_clk_set_rate,
+ .rate_config = {bus_rtbl, ARRAY_SIZE(bus_rtbl), 2},
.private_data = &ahb_config,
};
@@ -123,22 +144,40 @@ static struct aux_clk_masks aux_masks = {
.yscale_sel_shift = AUX_YSCALE_SHIFT,
};
-/* uart configurations */
-static struct aux_clk_config uart_config = {
+/* uart synth configurations */
+static struct aux_clk_config uart_synth_config = {
.synth_reg = UART_CLK_SYNT,
.masks = &aux_masks,
};
+/* aux rate configuration table, in ascending order of rates */
+struct aux_rate_tbl aux_rtbl[] = {
+ /* For PLL1 = 332 MHz */
+ {.xscale = 1, .yscale = 8, .eq = 1}, /* 41.5 MHz */
+ {.xscale = 1, .yscale = 4, .eq = 1}, /* 83 MHz */
+ {.xscale = 1, .yscale = 2, .eq = 1}, /* 166 MHz */
+};
+
+/* uart synth clock */
+static struct clk uart_synth_clk = {
+ .en_reg = UART_CLK_SYNT,
+ .en_reg_bit = AUX_SYNT_ENB,
+ .pclk = &pll1_clk,
+ .calc_rate = &aux_calc_rate,
+ .recalc = &aux_clk_recalc,
+ .set_rate = &aux_clk_set_rate,
+ .rate_config = {aux_rtbl, ARRAY_SIZE(aux_rtbl), 1},
+ .private_data = &uart_synth_config,
+};
+
/* uart parents */
static struct pclk_info uart_pclk_info[] = {
{
- .pclk = &pll1_clk,
- .pclk_mask = AUX_CLK_PLL1_MASK,
- .scalable = 1,
+ .pclk = &uart_synth_clk,
+ .pclk_val = AUX_CLK_PLL1_VAL,
}, {
.pclk = &pll3_48m_clk,
- .pclk_mask = AUX_CLK_PLL3_MASK,
- .scalable = 0,
+ .pclk_val = AUX_CLK_PLL3_VAL,
},
};
@@ -156,26 +195,35 @@ static struct clk uart_clk = {
.en_reg_bit = UART_CLK_ENB,
.pclk_sel = &uart_pclk_sel,
.pclk_sel_shift = UART_CLK_SHIFT,
- .recalc = &aux_clk_recalc,
- .private_data = &uart_config,
+ .recalc = &follow_parent,
};
/* firda configurations */
-static struct aux_clk_config firda_config = {
+static struct aux_clk_config firda_synth_config = {
.synth_reg = FIRDA_CLK_SYNT,
.masks = &aux_masks,
};
+/* firda synth clock */
+static struct clk firda_synth_clk = {
+ .en_reg = FIRDA_CLK_SYNT,
+ .en_reg_bit = AUX_SYNT_ENB,
+ .pclk = &pll1_clk,
+ .calc_rate = &aux_calc_rate,
+ .recalc = &aux_clk_recalc,
+ .set_rate = &aux_clk_set_rate,
+ .rate_config = {aux_rtbl, ARRAY_SIZE(aux_rtbl), 1},
+ .private_data = &firda_synth_config,
+};
+
/* firda parents */
static struct pclk_info firda_pclk_info[] = {
{
- .pclk = &pll1_clk,
- .pclk_mask = AUX_CLK_PLL1_MASK,
- .scalable = 1,
+ .pclk = &firda_synth_clk,
+ .pclk_val = AUX_CLK_PLL1_VAL,
}, {
.pclk = &pll3_48m_clk,
- .pclk_mask = AUX_CLK_PLL3_MASK,
- .scalable = 0,
+ .pclk_val = AUX_CLK_PLL3_VAL,
},
};
@@ -193,84 +241,155 @@ static struct clk firda_clk = {
.en_reg_bit = FIRDA_CLK_ENB,
.pclk_sel = &firda_pclk_sel,
.pclk_sel_shift = FIRDA_CLK_SHIFT,
- .recalc = &aux_clk_recalc,
- .private_data = &firda_config,
+ .recalc = &follow_parent,
+};
+
+/* gpt synthesizer masks */
+static struct gpt_clk_masks gpt_masks = {
+ .mscale_sel_mask = GPT_MSCALE_MASK,
+ .mscale_sel_shift = GPT_MSCALE_SHIFT,
+ .nscale_sel_mask = GPT_NSCALE_MASK,
+ .nscale_sel_shift = GPT_NSCALE_SHIFT,
+};
+
+/* gpt rate configuration table, in ascending order of rates */
+struct gpt_rate_tbl gpt_rtbl[] = {
+ /* For pll1 = 332 MHz */
+ {.mscale = 4, .nscale = 0}, /* 41.5 MHz */
+ {.mscale = 2, .nscale = 0}, /* 55.3 MHz */
+ {.mscale = 1, .nscale = 0}, /* 83 MHz */
+};
+
+/* gpt0 synth clk config*/
+static struct gpt_clk_config gpt0_synth_config = {
+ .synth_reg = PRSC1_CLK_CFG,
+ .masks = &gpt_masks,
+};
+
+/* gpt synth clock */
+static struct clk gpt0_synth_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &pll1_clk,
+ .calc_rate = &gpt_calc_rate,
+ .recalc = &gpt_clk_recalc,
+ .set_rate = &gpt_clk_set_rate,
+ .rate_config = {gpt_rtbl, ARRAY_SIZE(gpt_rtbl), 2},
+ .private_data = &gpt0_synth_config,
};
/* gpt parents */
-static struct pclk_info gpt_pclk_info[] = {
+static struct pclk_info gpt0_pclk_info[] = {
{
- .pclk = &pll1_clk,
- .pclk_mask = AUX_CLK_PLL1_MASK,
- .scalable = 1,
+ .pclk = &gpt0_synth_clk,
+ .pclk_val = AUX_CLK_PLL1_VAL,
}, {
.pclk = &pll3_48m_clk,
- .pclk_mask = AUX_CLK_PLL3_MASK,
- .scalable = 0,
+ .pclk_val = AUX_CLK_PLL3_VAL,
},
};
/* gpt parent select structure */
-static struct pclk_sel gpt_pclk_sel = {
- .pclk_info = gpt_pclk_info,
- .pclk_count = ARRAY_SIZE(gpt_pclk_info),
+static struct pclk_sel gpt0_pclk_sel = {
+ .pclk_info = gpt0_pclk_info,
+ .pclk_count = ARRAY_SIZE(gpt0_pclk_info),
.pclk_sel_reg = PERIP_CLK_CFG,
.pclk_sel_mask = GPT_CLK_MASK,
};
-/* gpt synthesizer masks */
-static struct gpt_clk_masks gpt_masks = {
- .mscale_sel_mask = GPT_MSCALE_MASK,
- .mscale_sel_shift = GPT_MSCALE_SHIFT,
- .nscale_sel_mask = GPT_NSCALE_MASK,
- .nscale_sel_shift = GPT_NSCALE_SHIFT,
+/* gpt0 timer clock */
+static struct clk gpt0_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk_sel = &gpt0_pclk_sel,
+ .pclk_sel_shift = GPT0_CLK_SHIFT,
+ .recalc = &follow_parent,
};
-/* gpt0 configurations */
-static struct gpt_clk_config gpt0_config = {
- .synth_reg = PRSC1_CLK_CFG,
+/* gpt1 synth clk configurations */
+static struct gpt_clk_config gpt1_synth_config = {
+ .synth_reg = PRSC2_CLK_CFG,
.masks = &gpt_masks,
};
-/* gpt0 timer clock */
-static struct clk gpt0_clk = {
+/* gpt1 synth clock */
+static struct clk gpt1_synth_clk = {
.flags = ALWAYS_ENABLED,
- .pclk_sel = &gpt_pclk_sel,
- .pclk_sel_shift = GPT0_CLK_SHIFT,
+ .pclk = &pll1_clk,
+ .calc_rate = &gpt_calc_rate,
.recalc = &gpt_clk_recalc,
- .private_data = &gpt0_config,
+ .set_rate = &gpt_clk_set_rate,
+ .rate_config = {gpt_rtbl, ARRAY_SIZE(gpt_rtbl), 2},
+ .private_data = &gpt1_synth_config,
};
-/* gpt1 configurations */
-static struct gpt_clk_config gpt1_config = {
- .synth_reg = PRSC2_CLK_CFG,
- .masks = &gpt_masks,
+static struct pclk_info gpt1_pclk_info[] = {
+ {
+ .pclk = &gpt1_synth_clk,
+ .pclk_val = AUX_CLK_PLL1_VAL,
+ }, {
+ .pclk = &pll3_48m_clk,
+ .pclk_val = AUX_CLK_PLL3_VAL,
+ },
+};
+
+/* gpt parent select structure */
+static struct pclk_sel gpt1_pclk_sel = {
+ .pclk_info = gpt1_pclk_info,
+ .pclk_count = ARRAY_SIZE(gpt1_pclk_info),
+ .pclk_sel_reg = PERIP_CLK_CFG,
+ .pclk_sel_mask = GPT_CLK_MASK,
};
/* gpt1 timer clock */
static struct clk gpt1_clk = {
.en_reg = PERIP1_CLK_ENB,
.en_reg_bit = GPT1_CLK_ENB,
- .pclk_sel = &gpt_pclk_sel,
+ .pclk_sel = &gpt1_pclk_sel,
.pclk_sel_shift = GPT1_CLK_SHIFT,
- .recalc = &gpt_clk_recalc,
- .private_data = &gpt1_config,
+ .recalc = &follow_parent,
};
-/* gpt2 configurations */
-static struct gpt_clk_config gpt2_config = {
+/* gpt2 synth clk configurations */
+static struct gpt_clk_config gpt2_synth_config = {
.synth_reg = PRSC3_CLK_CFG,
.masks = &gpt_masks,
};
+/* gpt1 synth clock */
+static struct clk gpt2_synth_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &pll1_clk,
+ .calc_rate = &gpt_calc_rate,
+ .recalc = &gpt_clk_recalc,
+ .set_rate = &gpt_clk_set_rate,
+ .rate_config = {gpt_rtbl, ARRAY_SIZE(gpt_rtbl), 2},
+ .private_data = &gpt2_synth_config,
+};
+
+static struct pclk_info gpt2_pclk_info[] = {
+ {
+ .pclk = &gpt2_synth_clk,
+ .pclk_val = AUX_CLK_PLL1_VAL,
+ }, {
+ .pclk = &pll3_48m_clk,
+ .pclk_val = AUX_CLK_PLL3_VAL,
+ },
+};
+
+/* gpt parent select structure */
+static struct pclk_sel gpt2_pclk_sel = {
+ .pclk_info = gpt2_pclk_info,
+ .pclk_count = ARRAY_SIZE(gpt2_pclk_info),
+ .pclk_sel_reg = PERIP_CLK_CFG,
+ .pclk_sel_mask = GPT_CLK_MASK,
+};
+
/* gpt2 timer clock */
static struct clk gpt2_clk = {
.en_reg = PERIP1_CLK_ENB,
.en_reg_bit = GPT2_CLK_ENB,
- .pclk_sel = &gpt_pclk_sel,
+ .pclk_sel = &gpt2_pclk_sel,
.pclk_sel_shift = GPT2_CLK_SHIFT,
- .recalc = &gpt_clk_recalc,
- .private_data = &gpt2_config,
+ .recalc = &follow_parent,
};
/* clock derived from pll3 clk */
@@ -290,13 +409,6 @@ static struct clk usbd_clk = {
.recalc = &follow_parent,
};
-/* clcd clock */
-static struct clk clcd_clk = {
- .flags = ALWAYS_ENABLED,
- .pclk = &pll3_48m_clk,
- .recalc = &follow_parent,
-};
-
/* clock derived from ahb clk */
/* apb masks structure */
static struct bus_clk_masks apb_masks = {
@@ -314,7 +426,10 @@ static struct bus_clk_config apb_config = {
static struct clk apb_clk = {
.flags = ALWAYS_ENABLED,
.pclk = &ahb_clk,
+ .calc_rate = &bus_calc_rate,
.recalc = &bus_clk_recalc,
+ .set_rate = &bus_clk_set_rate,
+ .rate_config = {bus_rtbl, ARRAY_SIZE(bus_rtbl), 2},
.private_data = &apb_config,
};
@@ -375,8 +490,17 @@ static struct clk adc_clk = {
.recalc = &follow_parent,
};
+#if defined(CONFIG_MACH_SPEAR310) || defined(CONFIG_MACH_SPEAR320)
+/* emi clock */
+static struct clk emi_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &ahb_clk,
+ .recalc = &follow_parent,
+};
+#endif
+
/* ssp clock */
-static struct clk ssp_clk = {
+static struct clk ssp0_clk = {
.pclk = &apb_clk,
.en_reg = PERIP1_CLK_ENB,
.en_reg_bit = SSP_CLK_ENB,
@@ -393,6 +517,137 @@ static struct clk gpio_clk = {
static struct clk dummy_apb_pclk;
+#if defined(CONFIG_MACH_SPEAR300) || defined(CONFIG_MACH_SPEAR310) || \
+ defined(CONFIG_MACH_SPEAR320)
+/* fsmc clock */
+static struct clk fsmc_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &ahb_clk,
+ .recalc = &follow_parent,
+};
+#endif
+
+/* common clocks to spear310 and spear320 */
+#if defined(CONFIG_MACH_SPEAR310) || defined(CONFIG_MACH_SPEAR320)
+/* uart1 clock */
+static struct clk uart1_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &apb_clk,
+ .recalc = &follow_parent,
+};
+
+/* uart2 clock */
+static struct clk uart2_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &apb_clk,
+ .recalc = &follow_parent,
+};
+#endif /* CONFIG_MACH_SPEAR310 || CONFIG_MACH_SPEAR320 */
+
+/* common clocks to spear300 and spear320 */
+#if defined(CONFIG_MACH_SPEAR300) || defined(CONFIG_MACH_SPEAR320)
+/* clcd clock */
+static struct clk clcd_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &pll3_48m_clk,
+ .recalc = &follow_parent,
+};
+
+/* sdhci clock */
+static struct clk sdhci_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &ahb_clk,
+ .recalc = &follow_parent,
+};
+#endif /* CONFIG_MACH_SPEAR300 || CONFIG_MACH_SPEAR320 */
+
+/* spear300 machine specific clock structures */
+#ifdef CONFIG_MACH_SPEAR300
+/* gpio1 clock */
+static struct clk gpio1_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &apb_clk,
+ .recalc = &follow_parent,
+};
+
+/* keyboard clock */
+static struct clk kbd_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &apb_clk,
+ .recalc = &follow_parent,
+};
+
+#endif
+
+/* spear310 machine specific clock structures */
+#ifdef CONFIG_MACH_SPEAR310
+/* uart3 clock */
+static struct clk uart3_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &apb_clk,
+ .recalc = &follow_parent,
+};
+
+/* uart4 clock */
+static struct clk uart4_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &apb_clk,
+ .recalc = &follow_parent,
+};
+
+/* uart5 clock */
+static struct clk uart5_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &apb_clk,
+ .recalc = &follow_parent,
+};
+#endif
+
+/* spear320 machine specific clock structures */
+#ifdef CONFIG_MACH_SPEAR320
+/* can0 clock */
+static struct clk can0_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &apb_clk,
+ .recalc = &follow_parent,
+};
+
+/* can1 clock */
+static struct clk can1_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &apb_clk,
+ .recalc = &follow_parent,
+};
+
+/* i2c1 clock */
+static struct clk i2c1_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &ahb_clk,
+ .recalc = &follow_parent,
+};
+
+/* ssp1 clock */
+static struct clk ssp1_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &apb_clk,
+ .recalc = &follow_parent,
+};
+
+/* ssp2 clock */
+static struct clk ssp2_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &apb_clk,
+ .recalc = &follow_parent,
+};
+
+/* pwm clock */
+static struct clk pwm_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &apb_clk,
+ .recalc = &follow_parent,
+};
+#endif
+
/* array of all spear 3xx clock lookups */
static struct clk_lookup spear_clk_lookups[] = {
{ .con_id = "apb_pclk", .clk = &dummy_apb_pclk},
@@ -400,7 +655,7 @@ static struct clk_lookup spear_clk_lookups[] = {
{ .con_id = "osc_32k_clk", .clk = &osc_32k_clk},
{ .con_id = "osc_24m_clk", .clk = &osc_24m_clk},
/* clock derived from 32 KHz osc clk */
- { .dev_id = "rtc", .clk = &rtc_clk},
+ { .dev_id = "rtc-spear", .clk = &rtc_clk},
/* clock derived from 24 MHz osc clk */
{ .con_id = "pll1_clk", .clk = &pll1_clk},
{ .con_id = "pll3_48m_clk", .clk = &pll3_48m_clk},
@@ -408,18 +663,22 @@ static struct clk_lookup spear_clk_lookups[] = {
/* clock derived from pll1 clk */
{ .con_id = "cpu_clk", .clk = &cpu_clk},
{ .con_id = "ahb_clk", .clk = &ahb_clk},
+ { .con_id = "uart_synth_clk", .clk = &uart_synth_clk},
+ { .con_id = "firda_synth_clk", .clk = &firda_synth_clk},
+ { .con_id = "gpt0_synth_clk", .clk = &gpt0_synth_clk},
+ { .con_id = "gpt1_synth_clk", .clk = &gpt1_synth_clk},
+ { .con_id = "gpt2_synth_clk", .clk = &gpt2_synth_clk},
{ .dev_id = "uart", .clk = &uart_clk},
{ .dev_id = "firda", .clk = &firda_clk},
{ .dev_id = "gpt0", .clk = &gpt0_clk},
{ .dev_id = "gpt1", .clk = &gpt1_clk},
{ .dev_id = "gpt2", .clk = &gpt2_clk},
/* clock derived from pll3 clk */
- { .dev_id = "usbh", .clk = &usbh_clk},
+ { .con_id = "usbh_clk", .clk = &usbh_clk},
{ .dev_id = "usbd", .clk = &usbd_clk},
- { .dev_id = "clcd", .clk = &clcd_clk},
/* clock derived from ahb clk */
{ .con_id = "apb_clk", .clk = &apb_clk},
- { .dev_id = "i2c", .clk = &i2c_clk},
+ { .dev_id = "i2c_designware.0", .clk = &i2c_clk},
{ .dev_id = "dma", .clk = &dma_clk},
{ .dev_id = "jpeg", .clk = &jpeg_clk},
{ .dev_id = "gmac", .clk = &gmac_clk},
@@ -427,8 +686,50 @@ static struct clk_lookup spear_clk_lookups[] = {
{ .dev_id = "c3", .clk = &c3_clk},
/* clock derived from apb clk */
{ .dev_id = "adc", .clk = &adc_clk},
- { .dev_id = "ssp", .clk = &ssp_clk},
+ { .dev_id = "ssp-pl022.0", .clk = &ssp0_clk},
{ .dev_id = "gpio", .clk = &gpio_clk},
+#if defined(CONFIG_MACH_SPEAR310) || defined(CONFIG_MACH_SPEAR320)
+ { .dev_id = "physmap-flash", .clk = &emi_clk},
+#endif
+#if defined(CONFIG_MACH_SPEAR300) || defined(CONFIG_MACH_SPEAR310) || \
+ defined(CONFIG_MACH_SPEAR320)
+ { .con_id = "fsmc", .clk = &fsmc_clk},
+#endif
+
+/* common clocks to spear310 and spear320 */
+#if defined(CONFIG_MACH_SPEAR310) || defined(CONFIG_MACH_SPEAR320)
+ { .dev_id = "uart1", .clk = &uart1_clk},
+ { .dev_id = "uart2", .clk = &uart2_clk},
+#endif
+
+ /* common clock to spear300 and spear320 */
+#if defined(CONFIG_MACH_SPEAR300) || defined(CONFIG_MACH_SPEAR320)
+ { .dev_id = "clcd", .clk = &clcd_clk},
+ { .dev_id = "sdhci", .clk = &sdhci_clk},
+#endif /* CONFIG_MACH_SPEAR300 || CONFIG_MACH_SPEAR320 */
+
+ /* spear300 machine specific clock structures */
+#ifdef CONFIG_MACH_SPEAR300
+ { .dev_id = "gpio1", .clk = &gpio1_clk},
+ { .dev_id = "keyboard", .clk = &kbd_clk},
+#endif
+
+ /* spear310 machine specific clock structures */
+#ifdef CONFIG_MACH_SPEAR310
+ { .dev_id = "uart3", .clk = &uart3_clk},
+ { .dev_id = "uart4", .clk = &uart4_clk},
+ { .dev_id = "uart5", .clk = &uart5_clk},
+
+#endif
+ /* spear320 machine specific clock structures */
+#ifdef CONFIG_MACH_SPEAR320
+ { .dev_id = "c_can_platform.0", .clk = &can0_clk},
+ { .dev_id = "c_can_platform.1", .clk = &can1_clk},
+ { .dev_id = "i2c_designware.1", .clk = &i2c1_clk},
+ { .dev_id = "ssp-pl022.1", .clk = &ssp1_clk},
+ { .dev_id = "ssp-pl022.2", .clk = &ssp2_clk},
+ { .dev_id = "pwm", .clk = &pwm_clk},
+#endif
};
void __init clk_init(void)
diff --git a/arch/arm/mach-spear3xx/include/mach/misc_regs.h b/arch/arm/mach-spear3xx/include/mach/misc_regs.h
index 6c919e1..0b93347 100644
--- a/arch/arm/mach-spear3xx/include/mach/misc_regs.h
+++ b/arch/arm/mach-spear3xx/include/mach/misc_regs.h
@@ -63,8 +63,8 @@
#define GPT1_CLK_SHIFT 11
#define GPT2_CLK_SHIFT 12
#define GPT_CLK_MASK 0x1
-#define AUX_CLK_PLL3_MASK 0
-#define AUX_CLK_PLL1_MASK 1
+#define AUX_CLK_PLL3_VAL 0
+#define AUX_CLK_PLL1_VAL 1
#define PERIP1_CLK_ENB (MISC_BASE + 0x02C)
/* PERIP1_CLK_ENB register masks */
@@ -113,6 +113,7 @@
#define RAS3_CLK_SYNT (MISC_BASE + 0x074)
#define RAS4_CLK_SYNT (MISC_BASE + 0x078)
/* aux clk synthesiser register masks for irda to ras4 */
+#define AUX_SYNT_ENB 31
#define AUX_EQ_SEL_SHIFT 30
#define AUX_EQ_SEL_MASK 1
#define AUX_EQ1_SEL 0
diff --git a/arch/arm/mach-spear6xx/clock.c b/arch/arm/mach-spear6xx/clock.c
index ef88922..9171952 100644
--- a/arch/arm/mach-spear6xx/clock.c
+++ b/arch/arm/mach-spear6xx/clock.c
@@ -60,12 +60,22 @@ static struct pll_clk_config pll1_config = {
.masks = &pll1_masks,
};
+/* pll rate configuration table, in ascending order of rates */
+struct pll_rate_tbl pll_rtbl[] = {
+ {.mode = 0, .m = 0x85, .n = 0x0C, .p = 0x1}, /* 266 MHz */
+ {.mode = 0, .m = 0xA6, .n = 0x0C, .p = 0x1}, /* 332 MHz */
+};
+
/* PLL1 clock */
static struct clk pll1_clk = {
+ .flags = ENABLED_ON_INIT,
.pclk = &osc_30m_clk,
.en_reg = PLL1_CTR,
.en_reg_bit = PLL_ENABLE,
+ .calc_rate = &pll_calc_rate,
.recalc = &pll_clk_recalc,
+ .set_rate = &pll_clk_set_rate,
+ .rate_config = {pll_rtbl, ARRAY_SIZE(pll_rtbl), 1},
.private_data = &pll1_config,
};
@@ -103,35 +113,25 @@ static struct bus_clk_config ahb_config = {
.masks = &ahb_masks,
};
+/* ahb rate configuration table, in ascending order of rates */
+struct bus_rate_tbl bus_rtbl[] = {
+ {.div = 3}, /* == parent divided by 4 */
+ {.div = 2}, /* == parent divided by 3 */
+ {.div = 1}, /* == parent divided by 2 */
+ {.div = 0}, /* == parent divided by 1 */
+};
+
/* ahb clock */
static struct clk ahb_clk = {
.flags = ALWAYS_ENABLED,
.pclk = &pll1_clk,
+ .calc_rate = &bus_calc_rate,
.recalc = &bus_clk_recalc,
+ .set_rate = &bus_clk_set_rate,
+ .rate_config = {bus_rtbl, ARRAY_SIZE(bus_rtbl), 2},
.private_data = &ahb_config,
};
-/* uart parents */
-static struct pclk_info uart_pclk_info[] = {
- {
- .pclk = &pll1_clk,
- .pclk_mask = AUX_CLK_PLL1_MASK,
- .scalable = 1,
- }, {
- .pclk = &pll3_48m_clk,
- .pclk_mask = AUX_CLK_PLL3_MASK,
- .scalable = 0,
- },
-};
-
-/* uart parent select structure */
-static struct pclk_sel uart_pclk_sel = {
- .pclk_info = uart_pclk_info,
- .pclk_count = ARRAY_SIZE(uart_pclk_info),
- .pclk_sel_reg = PERIP_CLK_CFG,
- .pclk_sel_mask = UART_CLK_MASK,
-};
-
/* auxiliary synthesizers masks */
static struct aux_clk_masks aux_masks = {
.eq_sel_mask = AUX_EQ_SEL_MASK,
@@ -145,19 +145,57 @@ static struct aux_clk_masks aux_masks = {
};
/* uart configurations */
-static struct aux_clk_config uart_config = {
+static struct aux_clk_config uart_synth_config = {
.synth_reg = UART_CLK_SYNT,
.masks = &aux_masks,
};
+/* aux rate configuration table, in ascending order of rates */
+struct aux_rate_tbl aux_rtbl[] = {
+ /* For PLL1 = 332 MHz */
+ {.xscale = 1, .yscale = 8, .eq = 1}, /* 41.5 MHz */
+ {.xscale = 1, .yscale = 4, .eq = 1}, /* 83 MHz */
+ {.xscale = 1, .yscale = 2, .eq = 1}, /* 166 MHz */
+};
+
+/* uart synth clock */
+static struct clk uart_synth_clk = {
+ .en_reg = UART_CLK_SYNT,
+ .en_reg_bit = AUX_SYNT_ENB,
+ .pclk = &pll1_clk,
+ .calc_rate = &aux_calc_rate,
+ .recalc = &aux_clk_recalc,
+ .set_rate = &aux_clk_set_rate,
+ .rate_config = {aux_rtbl, ARRAY_SIZE(aux_rtbl), 2},
+ .private_data = &uart_synth_config,
+};
+
+/* uart parents */
+static struct pclk_info uart_pclk_info[] = {
+ {
+ .pclk = &uart_synth_clk,
+ .pclk_val = AUX_CLK_PLL1_VAL,
+ }, {
+ .pclk = &pll3_48m_clk,
+ .pclk_val = AUX_CLK_PLL3_VAL,
+ },
+};
+
+/* uart parent select structure */
+static struct pclk_sel uart_pclk_sel = {
+ .pclk_info = uart_pclk_info,
+ .pclk_count = ARRAY_SIZE(uart_pclk_info),
+ .pclk_sel_reg = PERIP_CLK_CFG,
+ .pclk_sel_mask = UART_CLK_MASK,
+};
+
/* uart0 clock */
static struct clk uart0_clk = {
.en_reg = PERIP1_CLK_ENB,
.en_reg_bit = UART0_CLK_ENB,
.pclk_sel = &uart_pclk_sel,
.pclk_sel_shift = UART_CLK_SHIFT,
- .recalc = &aux_clk_recalc,
- .private_data = &uart_config,
+ .recalc = &follow_parent,
};
/* uart1 clock */
@@ -166,26 +204,35 @@ static struct clk uart1_clk = {
.en_reg_bit = UART1_CLK_ENB,
.pclk_sel = &uart_pclk_sel,
.pclk_sel_shift = UART_CLK_SHIFT,
- .recalc = &aux_clk_recalc,
- .private_data = &uart_config,
+ .recalc = &follow_parent,
};
/* firda configurations */
-static struct aux_clk_config firda_config = {
+static struct aux_clk_config firda_synth_config = {
.synth_reg = FIRDA_CLK_SYNT,
.masks = &aux_masks,
};
+/* firda synth clock */
+static struct clk firda_synth_clk = {
+ .en_reg = FIRDA_CLK_SYNT,
+ .en_reg_bit = AUX_SYNT_ENB,
+ .pclk = &pll1_clk,
+ .calc_rate = &aux_calc_rate,
+ .recalc = &aux_clk_recalc,
+ .set_rate = &aux_clk_set_rate,
+ .rate_config = {aux_rtbl, ARRAY_SIZE(aux_rtbl), 2},
+ .private_data = &firda_synth_config,
+};
+
/* firda parents */
static struct pclk_info firda_pclk_info[] = {
{
- .pclk = &pll1_clk,
- .pclk_mask = AUX_CLK_PLL1_MASK,
- .scalable = 1,
+ .pclk = &firda_synth_clk,
+ .pclk_val = AUX_CLK_PLL1_VAL,
}, {
.pclk = &pll3_48m_clk,
- .pclk_mask = AUX_CLK_PLL3_MASK,
- .scalable = 0,
+ .pclk_val = AUX_CLK_PLL3_VAL,
},
};
@@ -203,26 +250,35 @@ static struct clk firda_clk = {
.en_reg_bit = FIRDA_CLK_ENB,
.pclk_sel = &firda_pclk_sel,
.pclk_sel_shift = FIRDA_CLK_SHIFT,
- .recalc = &aux_clk_recalc,
- .private_data = &firda_config,
+ .recalc = &follow_parent,
};
/* clcd configurations */
-static struct aux_clk_config clcd_config = {
+static struct aux_clk_config clcd_synth_config = {
.synth_reg = CLCD_CLK_SYNT,
.masks = &aux_masks,
};
+/* firda synth clock */
+static struct clk clcd_synth_clk = {
+ .en_reg = CLCD_CLK_SYNT,
+ .en_reg_bit = AUX_SYNT_ENB,
+ .pclk = &pll1_clk,
+ .calc_rate = &aux_calc_rate,
+ .recalc = &aux_clk_recalc,
+ .set_rate = &aux_clk_set_rate,
+ .rate_config = {aux_rtbl, ARRAY_SIZE(aux_rtbl), 2},
+ .private_data = &clcd_synth_config,
+};
+
/* clcd parents */
static struct pclk_info clcd_pclk_info[] = {
{
- .pclk = &pll1_clk,
- .pclk_mask = AUX_CLK_PLL1_MASK,
- .scalable = 1,
+ .pclk = &clcd_synth_clk,
+ .pclk_val = AUX_CLK_PLL1_VAL,
}, {
.pclk = &pll3_48m_clk,
- .pclk_mask = AUX_CLK_PLL3_MASK,
- .scalable = 0,
+ .pclk_val = AUX_CLK_PLL3_VAL,
},
};
@@ -240,29 +296,7 @@ static struct clk clcd_clk = {
.en_reg_bit = CLCD_CLK_ENB,
.pclk_sel = &clcd_pclk_sel,
.pclk_sel_shift = CLCD_CLK_SHIFT,
- .recalc = &aux_clk_recalc,
- .private_data = &clcd_config,
-};
-
-/* gpt parents */
-static struct pclk_info gpt_pclk_info[] = {
- {
- .pclk = &pll1_clk,
- .pclk_mask = AUX_CLK_PLL1_MASK,
- .scalable = 1,
- }, {
- .pclk = &pll3_48m_clk,
- .pclk_mask = AUX_CLK_PLL3_MASK,
- .scalable = 0,
- },
-};
-
-/* gpt parent select structure */
-static struct pclk_sel gpt_pclk_sel = {
- .pclk_info = gpt_pclk_info,
- .pclk_count = ARRAY_SIZE(gpt_pclk_info),
- .pclk_sel_reg = PERIP_CLK_CFG,
- .pclk_sel_mask = GPT_CLK_MASK,
+ .recalc = &follow_parent,
};
/* gpt synthesizer masks */
@@ -273,60 +307,162 @@ static struct gpt_clk_masks gpt_masks = {
.nscale_sel_shift = GPT_NSCALE_SHIFT,
};
-/* gpt0_1 configurations */
-static struct gpt_clk_config gpt0_1_config = {
+/* gpt rate configuration table, in ascending order of rates */
+struct gpt_rate_tbl gpt_rtbl[] = {
+ /* For pll1 = 332 MHz */
+ {.mscale = 4, .nscale = 0}, /* 41.5 MHz */
+ {.mscale = 2, .nscale = 0}, /* 55.3 MHz */
+ {.mscale = 1, .nscale = 0}, /* 83 MHz */
+};
+
+/* gpt0 synth clk config*/
+static struct gpt_clk_config gpt0_synth_config = {
.synth_reg = PRSC1_CLK_CFG,
.masks = &gpt_masks,
};
+/* gpt synth clock */
+static struct clk gpt0_synth_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &pll1_clk,
+ .calc_rate = &gpt_calc_rate,
+ .recalc = &gpt_clk_recalc,
+ .set_rate = &gpt_clk_set_rate,
+ .rate_config = {gpt_rtbl, ARRAY_SIZE(gpt_rtbl), 2},
+ .private_data = &gpt0_synth_config,
+};
+
+/* gpt parents */
+static struct pclk_info gpt0_pclk_info[] = {
+ {
+ .pclk = &gpt0_synth_clk,
+ .pclk_val = AUX_CLK_PLL1_VAL,
+ }, {
+ .pclk = &pll3_48m_clk,
+ .pclk_val = AUX_CLK_PLL3_VAL,
+ },
+};
+
+/* gpt parent select structure */
+static struct pclk_sel gpt0_pclk_sel = {
+ .pclk_info = gpt0_pclk_info,
+ .pclk_count = ARRAY_SIZE(gpt0_pclk_info),
+ .pclk_sel_reg = PERIP_CLK_CFG,
+ .pclk_sel_mask = GPT_CLK_MASK,
+};
+
/* gpt0 ARM1 subsystem timer clock */
static struct clk gpt0_clk = {
.flags = ALWAYS_ENABLED,
- .pclk_sel = &gpt_pclk_sel,
+ .pclk_sel = &gpt0_pclk_sel,
.pclk_sel_shift = GPT0_CLK_SHIFT,
- .recalc = &gpt_clk_recalc,
- .private_data = &gpt0_1_config,
+ .recalc = &follow_parent,
+};
+
+
+/* Note: gpt0 and gpt1 share same parent clocks */
+/* gpt parent select structure */
+static struct pclk_sel gpt1_pclk_sel = {
+ .pclk_info = gpt0_pclk_info,
+ .pclk_count = ARRAY_SIZE(gpt0_pclk_info),
+ .pclk_sel_reg = PERIP_CLK_CFG,
+ .pclk_sel_mask = GPT_CLK_MASK,
};
/* gpt1 timer clock */
static struct clk gpt1_clk = {
.flags = ALWAYS_ENABLED,
- .pclk_sel = &gpt_pclk_sel,
+ .pclk_sel = &gpt1_pclk_sel,
.pclk_sel_shift = GPT1_CLK_SHIFT,
- .recalc = &gpt_clk_recalc,
- .private_data = &gpt0_1_config,
+ .recalc = &follow_parent,
};
-/* gpt2 configurations */
-static struct gpt_clk_config gpt2_config = {
+/* gpt2 synth clk config*/
+static struct gpt_clk_config gpt2_synth_config = {
.synth_reg = PRSC2_CLK_CFG,
.masks = &gpt_masks,
};
+/* gpt synth clock */
+static struct clk gpt2_synth_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &pll1_clk,
+ .calc_rate = &gpt_calc_rate,
+ .recalc = &gpt_clk_recalc,
+ .set_rate = &gpt_clk_set_rate,
+ .rate_config = {gpt_rtbl, ARRAY_SIZE(gpt_rtbl), 2},
+ .private_data = &gpt2_synth_config,
+};
+
+/* gpt parents */
+static struct pclk_info gpt2_pclk_info[] = {
+ {
+ .pclk = &gpt2_synth_clk,
+ .pclk_val = AUX_CLK_PLL1_VAL,
+ }, {
+ .pclk = &pll3_48m_clk,
+ .pclk_val = AUX_CLK_PLL3_VAL,
+ },
+};
+
+/* gpt parent select structure */
+static struct pclk_sel gpt2_pclk_sel = {
+ .pclk_info = gpt2_pclk_info,
+ .pclk_count = ARRAY_SIZE(gpt2_pclk_info),
+ .pclk_sel_reg = PERIP_CLK_CFG,
+ .pclk_sel_mask = GPT_CLK_MASK,
+};
+
/* gpt2 timer clock */
static struct clk gpt2_clk = {
- .en_reg = PERIP1_CLK_ENB,
- .en_reg_bit = GPT2_CLK_ENB,
- .pclk_sel = &gpt_pclk_sel,
+ .flags = ALWAYS_ENABLED,
+ .pclk_sel = &gpt2_pclk_sel,
.pclk_sel_shift = GPT2_CLK_SHIFT,
- .recalc = &gpt_clk_recalc,
- .private_data = &gpt2_config,
+ .recalc = &follow_parent,
};
-/* gpt3 configurations */
-static struct gpt_clk_config gpt3_config = {
+/* gpt3 synth clk config*/
+static struct gpt_clk_config gpt3_synth_config = {
.synth_reg = PRSC3_CLK_CFG,
.masks = &gpt_masks,
};
+/* gpt synth clock */
+static struct clk gpt3_synth_clk = {
+ .flags = ALWAYS_ENABLED,
+ .pclk = &pll1_clk,
+ .calc_rate = &gpt_calc_rate,
+ .recalc = &gpt_clk_recalc,
+ .set_rate = &gpt_clk_set_rate,
+ .rate_config = {gpt_rtbl, ARRAY_SIZE(gpt_rtbl), 2},
+ .private_data = &gpt3_synth_config,
+};
+
+/* gpt parents */
+static struct pclk_info gpt3_pclk_info[] = {
+ {
+ .pclk = &gpt3_synth_clk,
+ .pclk_val = AUX_CLK_PLL1_VAL,
+ }, {
+ .pclk = &pll3_48m_clk,
+ .pclk_val = AUX_CLK_PLL3_VAL,
+ },
+};
+
+/* gpt parent select structure */
+static struct pclk_sel gpt3_pclk_sel = {
+ .pclk_info = gpt3_pclk_info,
+ .pclk_count = ARRAY_SIZE(gpt3_pclk_info),
+ .pclk_sel_reg = PERIP_CLK_CFG,
+ .pclk_sel_mask = GPT_CLK_MASK,
+};
+
/* gpt3 timer clock */
static struct clk gpt3_clk = {
- .en_reg = PERIP1_CLK_ENB,
- .en_reg_bit = GPT3_CLK_ENB,
- .pclk_sel = &gpt_pclk_sel,
+ .flags = ALWAYS_ENABLED,
+ .pclk_sel = &gpt3_pclk_sel,
.pclk_sel_shift = GPT3_CLK_SHIFT,
- .recalc = &gpt_clk_recalc,
- .private_data = &gpt3_config,
+ .recalc = &follow_parent,
};
/* clock derived from pll3 clk */
@@ -371,7 +507,10 @@ static struct bus_clk_config apb_config = {
static struct clk apb_clk = {
.flags = ALWAYS_ENABLED,
.pclk = &ahb_clk,
+ .calc_rate = &bus_calc_rate,
.recalc = &bus_clk_recalc,
+ .set_rate = &bus_clk_set_rate,
+ .rate_config = {bus_rtbl, ARRAY_SIZE(bus_rtbl), 2},
.private_data = &apb_config,
};
@@ -488,7 +627,7 @@ static struct clk_lookup spear_clk_lookups[] = {
{ .con_id = "osc_32k_clk", .clk = &osc_32k_clk},
{ .con_id = "osc_30m_clk", .clk = &osc_30m_clk},
/* clock derived from 32 KHz os clk */
- { .dev_id = "rtc", .clk = &rtc_clk},
+ { .dev_id = "rtc-spear", .clk = &rtc_clk},
/* clock derived from 30 MHz os clk */
{ .con_id = "pll1_clk", .clk = &pll1_clk},
{ .con_id = "pll3_48m_clk", .clk = &pll3_48m_clk},
@@ -496,6 +635,12 @@ static struct clk_lookup spear_clk_lookups[] = {
/* clock derived from pll1 clk */
{ .con_id = "cpu_clk", .clk = &cpu_clk},
{ .con_id = "ahb_clk", .clk = &ahb_clk},
+ { .con_id = "uart_synth_clk", .clk = &uart_synth_clk},
+ { .con_id = "firda_synth_clk", .clk = &firda_synth_clk},
+ { .con_id = "clcd_synth_clk", .clk = &clcd_synth_clk},
+ { .con_id = "gpt0_synth_clk", .clk = &gpt0_synth_clk},
+ { .con_id = "gpt2_synth_clk", .clk = &gpt2_synth_clk},
+ { .con_id = "gpt3_synth_clk", .clk = &gpt3_synth_clk},
{ .dev_id = "uart0", .clk = &uart0_clk},
{ .dev_id = "uart1", .clk = &uart1_clk},
{ .dev_id = "firda", .clk = &firda_clk},
@@ -505,22 +650,22 @@ static struct clk_lookup spear_clk_lookups[] = {
{ .dev_id = "gpt2", .clk = &gpt2_clk},
{ .dev_id = "gpt3", .clk = &gpt3_clk},
/* clock derived from pll3 clk */
- { .dev_id = "usbh0", .clk = &usbh0_clk},
- { .dev_id = "usbh1", .clk = &usbh1_clk},
+ { .con_id = "usbh.0_clk", .clk = &usbh0_clk},
+ { .con_id = "usbh.1_clk", .clk = &usbh1_clk},
{ .dev_id = "usbd", .clk = &usbd_clk},
/* clock derived from ahb clk */
{ .con_id = "apb_clk", .clk = &apb_clk},
- { .dev_id = "i2c", .clk = &i2c_clk},
+ { .dev_id = "i2c_designware.0", .clk = &i2c_clk},
{ .dev_id = "dma", .clk = &dma_clk},
{ .dev_id = "jpeg", .clk = &jpeg_clk},
{ .dev_id = "gmac", .clk = &gmac_clk},
{ .dev_id = "smi", .clk = &smi_clk},
- { .dev_id = "fsmc", .clk = &fsmc_clk},
+ { .con_id = "fsmc", .clk = &fsmc_clk},
/* clock derived from apb clk */
{ .dev_id = "adc", .clk = &adc_clk},
- { .dev_id = "ssp0", .clk = &ssp0_clk},
- { .dev_id = "ssp1", .clk = &ssp1_clk},
- { .dev_id = "ssp2", .clk = &ssp2_clk},
+ { .dev_id = "ssp-pl022.0", .clk = &ssp0_clk},
+ { .dev_id = "ssp-pl022.1", .clk = &ssp1_clk},
+ { .dev_id = "ssp-pl022.2", .clk = &ssp2_clk},
{ .dev_id = "gpio0", .clk = &gpio0_clk},
{ .dev_id = "gpio1", .clk = &gpio1_clk},
{ .dev_id = "gpio2", .clk = &gpio2_clk},
diff --git a/arch/arm/mach-spear6xx/include/mach/misc_regs.h b/arch/arm/mach-spear6xx/include/mach/misc_regs.h
index d153177..45571c1 100644
--- a/arch/arm/mach-spear6xx/include/mach/misc_regs.h
+++ b/arch/arm/mach-spear6xx/include/mach/misc_regs.h
@@ -66,8 +66,8 @@
#define GPT2_CLK_SHIFT 11
#define GPT3_CLK_SHIFT 12
#define GPT_CLK_MASK 0x1
-#define AUX_CLK_PLL3_MASK 0
-#define AUX_CLK_PLL1_MASK 1
+#define AUX_CLK_PLL3_VAL 0
+#define AUX_CLK_PLL1_VAL 1
#define PERIP1_CLK_ENB (MISC_BASE + 0x02C)
/* PERIP1_CLK_ENB register masks */
@@ -123,6 +123,7 @@
#define RAS3_CLK_SYNT (MISC_BASE + 0x074)
#define RAS4_CLK_SYNT (MISC_BASE + 0x078)
/* aux clk synthesiser register masks for irda to ras4 */
+#define AUX_SYNT_ENB 31
#define AUX_EQ_SEL_SHIFT 30
#define AUX_EQ_SEL_MASK 1
#define AUX_EQ1_SEL 0
diff --git a/arch/arm/plat-spear/clock.c b/arch/arm/plat-spear/clock.c
index f1cf832..7e7ab60 100644
--- a/arch/arm/plat-spear/clock.c
+++ b/arch/arm/plat-spear/clock.c
@@ -12,6 +12,7 @@
*/
#include <linux/bug.h>
+#include <linux/clk.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/list.h>
@@ -22,7 +23,7 @@
static DEFINE_SPINLOCK(clocks_lock);
static LIST_HEAD(root_clks);
-static void propagate_rate(struct list_head *);
+static void propagate_rate(struct clk *, int on_init);
static int generic_clk_enable(struct clk *clk)
{
@@ -64,6 +65,100 @@ static struct clkops generic_clkops = {
.disable = generic_clk_disable,
};
+/* returns current programmed clocks clock info structure */
+static struct pclk_info *pclk_info_get(struct clk *clk)
+{
+ unsigned int val, i;
+ struct pclk_info *info = NULL;
+
+ val = (readl(clk->pclk_sel->pclk_sel_reg) >> clk->pclk_sel_shift)
+ & clk->pclk_sel->pclk_sel_mask;
+
+ for (i = 0; i < clk->pclk_sel->pclk_count; i++) {
+ if (clk->pclk_sel->pclk_info[i].pclk_val == val)
+ info = &clk->pclk_sel->pclk_info[i];
+ }
+
+ return info;
+}
+
+/*
+ * Set Update pclk, and pclk_info of clk and add clock sibling node to current
+ * parents children list
+ */
+static void clk_reparent(struct clk *clk, struct pclk_info *pclk_info)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&clocks_lock, flags);
+ list_del(&clk->sibling);
+ list_add(&clk->sibling, &pclk_info->pclk->children);
+
+ clk->pclk = pclk_info->pclk;
+ spin_unlock_irqrestore(&clocks_lock, flags);
+}
+
+static void do_clk_disable(struct clk *clk)
+{
+ if (!clk)
+ return;
+
+ if (!clk->usage_count) {
+ WARN_ON(1);
+ return;
+ }
+
+ clk->usage_count--;
+
+ if (clk->usage_count == 0) {
+ /*
+ * Surely, there are no active childrens or direct users
+ * of this clock
+ */
+ if (clk->pclk)
+ do_clk_disable(clk->pclk);
+
+ if (clk->ops && clk->ops->disable)
+ clk->ops->disable(clk);
+ }
+}
+
+static int do_clk_enable(struct clk *clk)
+{
+ int ret = 0;
+
+ if (!clk)
+ return -EFAULT;
+
+ if (clk->usage_count == 0) {
+ if (clk->pclk) {
+ ret = do_clk_enable(clk->pclk);
+ if (ret)
+ goto err;
+ }
+ if (clk->ops && clk->ops->enable) {
+ ret = clk->ops->enable(clk);
+ if (ret) {
+ if (clk->pclk)
+ do_clk_disable(clk->pclk);
+ goto err;
+ }
+ }
+ /*
+ * Since the clock is going to be used for the first
+ * time please reclac
+ */
+ if (clk->recalc) {
+ ret = clk->recalc(clk);
+ if (ret)
+ goto err;
+ }
+ }
+ clk->usage_count++;
+err:
+ return ret;
+}
+
/*
* clk_enable - inform the system when the clock source should be running.
* @clk: clock source
@@ -77,17 +172,9 @@ int clk_enable(struct clk *clk)
unsigned long flags;
int ret = 0;
- if (!clk || IS_ERR(clk))
- return -EFAULT;
-
spin_lock_irqsave(&clocks_lock, flags);
- if (clk->usage_count == 0) {
- if (clk->ops && clk->ops->enable)
- ret = clk->ops->enable(clk);
- }
- clk->usage_count++;
+ ret = do_clk_enable(clk);
spin_unlock_irqrestore(&clocks_lock, flags);
-
return ret;
}
EXPORT_SYMBOL(clk_enable);
@@ -108,17 +195,8 @@ void clk_disable(struct clk *clk)
{
unsigned long flags;
- if (!clk || IS_ERR(clk))
- return;
-
- WARN_ON(clk->usage_count == 0);
-
spin_lock_irqsave(&clocks_lock, flags);
- clk->usage_count--;
- if (clk->usage_count == 0) {
- if (clk->ops && clk->ops->disable)
- clk->ops->disable(clk);
- }
+ do_clk_disable(clk);
spin_unlock_irqrestore(&clocks_lock, flags);
}
EXPORT_SYMBOL(clk_disable);
@@ -152,15 +230,14 @@ int clk_set_parent(struct clk *clk, struct clk *parent)
int i, found = 0, val = 0;
unsigned long flags;
- if (!clk || IS_ERR(clk) || !parent || IS_ERR(parent))
+ if (!clk || !parent)
return -EFAULT;
- if (clk->usage_count)
- return -EBUSY;
- if (!clk->pclk_sel)
- return -EPERM;
if (clk->pclk == parent)
return 0;
+ if (!clk->pclk_sel)
+ return -EPERM;
+ /* check if requested parent is in clk parent list */
for (i = 0; i < clk->pclk_sel->pclk_count; i++) {
if (clk->pclk_sel->pclk_info[i].pclk == parent) {
found = 1;
@@ -175,13 +252,14 @@ int clk_set_parent(struct clk *clk, struct clk *parent)
/* reflect parent change in hardware */
val = readl(clk->pclk_sel->pclk_sel_reg);
val &= ~(clk->pclk_sel->pclk_sel_mask << clk->pclk_sel_shift);
- val |= clk->pclk_sel->pclk_info[i].pclk_mask << clk->pclk_sel_shift;
+ val |= clk->pclk_sel->pclk_info[i].pclk_val << clk->pclk_sel_shift;
writel(val, clk->pclk_sel->pclk_sel_reg);
spin_unlock_irqrestore(&clocks_lock, flags);
/* reflect parent change in software */
- clk->recalc(clk);
- propagate_rate(&clk->children);
+ clk_reparent(clk, &clk->pclk_sel->pclk_info[i]);
+
+ propagate_rate(clk, 0);
return 0;
}
EXPORT_SYMBOL(clk_set_parent);
@@ -195,19 +273,37 @@ EXPORT_SYMBOL(clk_set_parent);
*/
int clk_set_rate(struct clk *clk, unsigned long rate)
{
- /* TODO */
- return -EINVAL;
+ unsigned long flags;
+ int ret = -EINVAL;
+
+ if (!clk || !rate)
+ return -EFAULT;
+
+ if (clk->set_rate) {
+ spin_lock_irqsave(&clocks_lock, flags);
+ ret = clk->set_rate(clk, rate);
+ if (!ret)
+ /* if successful -> propagate */
+ propagate_rate(clk, 0);
+ spin_unlock_irqrestore(&clocks_lock, flags);
+ } else if (clk->pclk) {
+ u32 mult = clk->div_factor ? clk->div_factor : 1;
+ ret = clk_set_rate(clk->pclk, mult * rate);
+ }
+
+ return ret;
}
EXPORT_SYMBOL(clk_set_rate);
/* registers clock in platform clock framework */
void clk_register(struct clk_lookup *cl)
{
- struct clk *clk = cl->clk;
+ struct clk *clk;
unsigned long flags;
- if (!clk || IS_ERR(clk))
+ if (!cl || !cl->clk)
return;
+ clk = cl->clk;
spin_lock_irqsave(&clocks_lock, flags);
@@ -220,15 +316,24 @@ void clk_register(struct clk_lookup *cl)
/* root clock don't have any parents */
if (!clk->pclk && !clk->pclk_sel) {
list_add(&clk->sibling, &root_clks);
- /* add clocks with only one parent to parent's children list */
} else if (clk->pclk && !clk->pclk_sel) {
+ /* add clocks with only one parent to parent's children list */
list_add(&clk->sibling, &clk->pclk->children);
} else {
- /* add clocks with > 1 parent to 1st parent's children list */
- clk->pclk = clk->pclk_sel->pclk_info[0].pclk;
- list_add(&clk->sibling,
- &clk->pclk_sel->pclk_info[0].pclk->children);
+ /* clocks with more than one parent */
+ struct pclk_info *pclk_info;
+
+ pclk_info = pclk_info_get(clk);
+ if (!pclk_info) {
+ pr_err("CLKDEV: invalid pclk info of clk with"
+ " %s dev_id and %s con_id\n",
+ cl->dev_id, cl->con_id);
+ } else {
+ clk->pclk = pclk_info->pclk;
+ list_add(&clk->sibling, &pclk_info->pclk->children);
+ }
}
+
spin_unlock_irqrestore(&clocks_lock, flags);
/* add clock to arm clockdev framework */
@@ -236,56 +341,142 @@ void clk_register(struct clk_lookup *cl)
}
/**
- * propagate_rate - recalculate and propagate all clocks in list head
+ * propagate_rate - recalculate and propagate all clocks to children
+ * @pclk: parent clock required to be propogated
+ * @on_init: flag for enabling clocks which are ENABLED_ON_INIT.
*
- * Recalculates all root clocks in list head, which if the clock's .recalc is
- * set correctly, should also propagate their rates.
+ * Recalculates all children clocks
*/
-static void propagate_rate(struct list_head *lhead)
+void propagate_rate(struct clk *pclk, int on_init)
{
- struct clk *clkp, *_temp;
+ struct clk *clk, *_temp;
+ int ret = 0;
+
+ list_for_each_entry_safe(clk, _temp, &pclk->children, sibling) {
+ if (clk->recalc) {
+ ret = clk->recalc(clk);
+ /*
+ * recalc will return error if clk out is not programmed
+ * In this case configure default rate.
+ */
+ if (ret && clk->set_rate)
+ clk->set_rate(clk, 0);
+ }
+ propagate_rate(clk, on_init);
+
+ if (!on_init)
+ continue;
- list_for_each_entry_safe(clkp, _temp, lhead, sibling) {
- if (clkp->recalc)
- clkp->recalc(clkp);
- propagate_rate(&clkp->children);
+ /* Enable clks enabled on init, in software view */
+ if (clk->flags & ENABLED_ON_INIT)
+ do_clk_enable(clk);
}
}
-/* returns current programmed clocks clock info structure */
-static struct pclk_info *pclk_info_get(struct clk *clk)
+/**
+ * round_rate_index - return closest programmable rate index in rate_config tbl
+ * @clk: ptr to clock structure
+ * @drate: desired rate
+ * @rate: final rate will be returned in this variable only.
+ *
+ * Finds index in rate_config for highest clk rate which is less than
+ * requested rate. If there is no clk rate lesser than requested rate then
+ * -EINVAL is returned. This routine assumes that rate_config is written
+ * in incrementing order of clk rates.
+ * If drate passed is zero then default rate is programmed.
+ */
+static int
+round_rate_index(struct clk *clk, unsigned long drate, unsigned long *rate)
{
- unsigned int mask, i;
- unsigned long flags;
- struct pclk_info *info = NULL;
+ unsigned long tmp = 0, prev_rate = 0;
+ int index;
- spin_lock_irqsave(&clocks_lock, flags);
- mask = (readl(clk->pclk_sel->pclk_sel_reg) >> clk->pclk_sel_shift)
- & clk->pclk_sel->pclk_sel_mask;
+ if (!clk->calc_rate)
+ return -EFAULT;
- for (i = 0; i < clk->pclk_sel->pclk_count; i++) {
- if (clk->pclk_sel->pclk_info[i].pclk_mask == mask)
- info = &clk->pclk_sel->pclk_info[i];
+ if (!drate)
+ return -EINVAL;
+
+ /*
+ * This loops ends on two conditions:
+ * - as soon as clk is found with rate greater than requested rate.
+ * - if all clks in rate_config are smaller than requested rate.
+ */
+ for (index = 0; index < clk->rate_config.count; index++) {
+ prev_rate = tmp;
+ tmp = clk->calc_rate(clk, index);
+ if (drate < tmp) {
+ index--;
+ break;
+ }
}
- spin_unlock_irqrestore(&clocks_lock, flags);
+ /* return if can't find suitable clock */
+ if (index < 0) {
+ index = -EINVAL;
+ *rate = 0;
+ } else if (index == clk->rate_config.count) {
+ /* program with highest clk rate possible */
+ index = clk->rate_config.count - 1;
+ *rate = tmp;
+ } else
+ *rate = prev_rate;
- return info;
+ return index;
}
-/*
- * Set pclk as cclk's parent and add clock sibling node to current parents
- * children list
+/**
+ * clk_round_rate - adjust a rate to the exact rate a clock can provide
+ * @clk: clock source
+ * @rate: desired clock rate in Hz
+ *
+ * Returns rounded clock rate in Hz, or negative errno.
*/
-static void change_parent(struct clk *cclk, struct clk *pclk)
+long clk_round_rate(struct clk *clk, unsigned long drate)
{
- unsigned long flags;
+ long rate = 0;
+ int index;
+
+ /*
+ * propagate call to parent who supports calc_rate. Similar approach is
+ * used in clk_set_rate.
+ */
+ if (!clk->calc_rate) {
+ u32 mult;
+ if (!clk->pclk)
+ return clk->rate;
+
+ mult = clk->div_factor ? clk->div_factor : 1;
+ return clk_round_rate(clk->pclk, mult * drate) / mult;
+ }
- spin_lock_irqsave(&clocks_lock, flags);
- list_del(&cclk->sibling);
- list_add(&cclk->sibling, &pclk->children);
+ index = round_rate_index(clk, drate, &rate);
+ if (index >= 0)
+ return rate;
+ else
+ return index;
+}
+EXPORT_SYMBOL(clk_round_rate);
- cclk->pclk = pclk;
- spin_unlock_irqrestore(&clocks_lock, flags);
+/*All below functions are called with lock held */
+
+/*
+ * Calculates pll clk rate for specific value of mode, m, n and p
+ *
+ * In normal mode
+ * rate = (2 * M[15:8] * Fin)/(N * 2^P)
+ *
+ * In Dithered mode
+ * rate = (2 * M[15:0] * Fin)/(256 * N * 2^P)
+ */
+unsigned long pll_calc_rate(struct clk *clk, int index)
+{
+ unsigned long rate = clk->pclk->rate;
+ struct pll_rate_tbl *tbls = clk->rate_config.tbls;
+ unsigned int mode;
+
+ mode = tbls[index].mode ? 256 : 1;
+ return (((2 * rate / 10000) * tbls[index].m) /
+ (mode * tbls[index].n * (1 << tbls[index].p))) * 10000;
}
/*
@@ -297,13 +488,11 @@ static void change_parent(struct clk *cclk, struct clk *pclk)
* In Dithered mode
* rate = (2 * M[15:0] * Fin)/(256 * N * 2^P)
*/
-void pll_clk_recalc(struct clk *clk)
+int pll_clk_recalc(struct clk *clk)
{
struct pll_clk_config *config = clk->private_data;
unsigned int num = 2, den = 0, val, mode = 0;
- unsigned long flags;
- spin_lock_irqsave(&clocks_lock, flags);
mode = (readl(config->mode_reg) >> config->masks->mode_shift) &
config->masks->mode_mask;
@@ -325,22 +514,120 @@ void pll_clk_recalc(struct clk *clk)
den *= 256;
}
+ if (!den)
+ return -EINVAL;
+
clk->rate = (((clk->pclk->rate/10000) * num) / den) * 10000;
- spin_unlock_irqrestore(&clocks_lock, flags);
+ return 0;
+}
+
+/*
+ * Configures new clock rate of pll
+ */
+int pll_clk_set_rate(struct clk *clk, unsigned long desired_rate)
+{
+ struct pll_rate_tbl *tbls = clk->rate_config.tbls;
+ struct pll_clk_config *config = clk->private_data;
+ unsigned long val, rate;
+ int i;
+
+ i = round_rate_index(clk, desired_rate, &rate);
+ if (i < 0)
+ return i;
+
+ val = readl(config->mode_reg) &
+ ~(config->masks->mode_mask << config->masks->mode_shift);
+ val |= (tbls[i].mode & config->masks->mode_mask) <<
+ config->masks->mode_shift;
+ writel(val, config->mode_reg);
+
+ val = readl(config->cfg_reg) &
+ ~(config->masks->div_p_mask << config->masks->div_p_shift);
+ val |= (tbls[i].p & config->masks->div_p_mask) <<
+ config->masks->div_p_shift;
+ val &= ~(config->masks->div_n_mask << config->masks->div_n_shift);
+ val |= (tbls[i].n & config->masks->div_n_mask) <<
+ config->masks->div_n_shift;
+ val &= ~(config->masks->dith_fdbk_m_mask <<
+ config->masks->dith_fdbk_m_shift);
+ if (tbls[i].mode)
+ val |= (tbls[i].m & config->masks->dith_fdbk_m_mask) <<
+ config->masks->dith_fdbk_m_shift;
+ else
+ val |= (tbls[i].m & config->masks->norm_fdbk_m_mask) <<
+ config->masks->norm_fdbk_m_shift;
+
+ writel(val, config->cfg_reg);
+
+ clk->rate = rate;
+
+ return 0;
+}
+
+/*
+ * Calculates ahb, apb clk rate for specific value of div
+ */
+unsigned long bus_calc_rate(struct clk *clk, int index)
+{
+ unsigned long rate = clk->pclk->rate;
+ struct bus_rate_tbl *tbls = clk->rate_config.tbls;
+
+ return rate / (tbls[index].div + 1);
}
/* calculates current programmed rate of ahb or apb bus */
-void bus_clk_recalc(struct clk *clk)
+int bus_clk_recalc(struct clk *clk)
{
struct bus_clk_config *config = clk->private_data;
unsigned int div;
- unsigned long flags;
- spin_lock_irqsave(&clocks_lock, flags);
div = ((readl(config->reg) >> config->masks->shift) &
config->masks->mask) + 1;
+
+ if (!div)
+ return -EINVAL;
+
clk->rate = (unsigned long)clk->pclk->rate / div;
- spin_unlock_irqrestore(&clocks_lock, flags);
+ return 0;
+}
+
+/* Configures new clock rate of AHB OR APB bus */
+int bus_clk_set_rate(struct clk *clk, unsigned long desired_rate)
+{
+ struct bus_rate_tbl *tbls = clk->rate_config.tbls;
+ struct bus_clk_config *config = clk->private_data;
+ unsigned long val, rate;
+ int i;
+
+ i = round_rate_index(clk, desired_rate, &rate);
+ if (i < 0)
+ return i;
+
+ val = readl(config->reg) &
+ ~(config->masks->mask << config->masks->shift);
+ val |= (tbls[i].div & config->masks->mask) << config->masks->shift;
+ writel(val, config->reg);
+
+ clk->rate = rate;
+
+ return 0;
+}
+
+/*
+ * gives rate for different values of eq, x and y
+ *
+ * Fout from synthesizer can be given from two equations:
+ * Fout1 = (Fin * X/Y)/2 EQ1
+ * Fout2 = Fin * X/Y EQ2
+ */
+unsigned long aux_calc_rate(struct clk *clk, int index)
+{
+ unsigned long rate = clk->pclk->rate;
+ struct aux_rate_tbl *tbls = clk->rate_config.tbls;
+ u8 eq = tbls[index].eq ? 1 : 2;
+
+ return (((rate/10000) * tbls[index].xscale) /
+ (tbls[index].yscale * eq)) * 10000;
}
/*
@@ -353,47 +640,76 @@ void bus_clk_recalc(struct clk *clk)
*
* Selection of eqn 1 or 2 is programmed in register
*/
-void aux_clk_recalc(struct clk *clk)
+int aux_clk_recalc(struct clk *clk)
{
struct aux_clk_config *config = clk->private_data;
- struct pclk_info *pclk_info = NULL;
unsigned int num = 1, den = 1, val, eqn;
- unsigned long flags;
- /* get current programmed parent */
- pclk_info = pclk_info_get(clk);
- if (!pclk_info) {
- spin_lock_irqsave(&clocks_lock, flags);
- clk->pclk = NULL;
- clk->rate = 0;
- spin_unlock_irqrestore(&clocks_lock, flags);
- return;
- }
+ val = readl(config->synth_reg);
- change_parent(clk, pclk_info->pclk);
+ eqn = (val >> config->masks->eq_sel_shift) &
+ config->masks->eq_sel_mask;
+ if (eqn == config->masks->eq1_mask)
+ den *= 2;
- spin_lock_irqsave(&clocks_lock, flags);
- if (pclk_info->scalable) {
- val = readl(config->synth_reg);
-
- eqn = (val >> config->masks->eq_sel_shift) &
- config->masks->eq_sel_mask;
- if (eqn == config->masks->eq1_mask)
- den *= 2;
-
- /* calculate numerator */
- num = (val >> config->masks->xscale_sel_shift) &
- config->masks->xscale_sel_mask;
-
- /* calculate denominator */
- den *= (val >> config->masks->yscale_sel_shift) &
- config->masks->yscale_sel_mask;
- val = (((clk->pclk->rate/10000) * num) / den) * 10000;
- } else
- val = clk->pclk->rate;
+ /* calculate numerator */
+ num = (val >> config->masks->xscale_sel_shift) &
+ config->masks->xscale_sel_mask;
- clk->rate = val;
- spin_unlock_irqrestore(&clocks_lock, flags);
+ /* calculate denominator */
+ den *= (val >> config->masks->yscale_sel_shift) &
+ config->masks->yscale_sel_mask;
+
+ if (!den)
+ return -EINVAL;
+
+ clk->rate = (((clk->pclk->rate/10000) * num) / den) * 10000;
+ return 0;
+}
+
+/* Configures new clock rate of auxiliary synthesizers used by: UART, FIRDA*/
+int aux_clk_set_rate(struct clk *clk, unsigned long desired_rate)
+{
+ struct aux_rate_tbl *tbls = clk->rate_config.tbls;
+ struct aux_clk_config *config = clk->private_data;
+ unsigned long val, rate;
+ int i;
+
+ i = round_rate_index(clk, desired_rate, &rate);
+ if (i < 0)
+ return i;
+
+ val = readl(config->synth_reg) &
+ ~(config->masks->eq_sel_mask << config->masks->eq_sel_shift);
+ val |= (tbls[i].eq & config->masks->eq_sel_mask) <<
+ config->masks->eq_sel_shift;
+ val &= ~(config->masks->xscale_sel_mask <<
+ config->masks->xscale_sel_shift);
+ val |= (tbls[i].xscale & config->masks->xscale_sel_mask) <<
+ config->masks->xscale_sel_shift;
+ val &= ~(config->masks->yscale_sel_mask <<
+ config->masks->yscale_sel_shift);
+ val |= (tbls[i].yscale & config->masks->yscale_sel_mask) <<
+ config->masks->yscale_sel_shift;
+ writel(val, config->synth_reg);
+
+ clk->rate = rate;
+
+ return 0;
+}
+
+/*
+ * Calculates gpt clk rate for different values of mscale and nscale
+ *
+ * Fout= Fin/((2 ^ (N+1)) * (M+1))
+ */
+unsigned long gpt_calc_rate(struct clk *clk, int index)
+{
+ unsigned long rate = clk->pclk->rate;
+ struct gpt_rate_tbl *tbls = clk->rate_config.tbls;
+
+ return rate / ((1 << (tbls[index].nscale + 1)) *
+ (tbls[index].mscale + 1));
}
/*
@@ -401,49 +717,142 @@ void aux_clk_recalc(struct clk *clk)
* Fout from synthesizer can be given from below equations:
* Fout= Fin/((2 ^ (N+1)) * (M+1))
*/
-void gpt_clk_recalc(struct clk *clk)
+int gpt_clk_recalc(struct clk *clk)
{
struct gpt_clk_config *config = clk->private_data;
- struct pclk_info *pclk_info = NULL;
unsigned int div = 1, val;
- unsigned long flags;
- pclk_info = pclk_info_get(clk);
- if (!pclk_info) {
- spin_lock_irqsave(&clocks_lock, flags);
- clk->pclk = NULL;
- clk->rate = 0;
- spin_unlock_irqrestore(&clocks_lock, flags);
- return;
- }
+ val = readl(config->synth_reg);
+ div += (val >> config->masks->mscale_sel_shift) &
+ config->masks->mscale_sel_mask;
+ div *= 1 << (((val >> config->masks->nscale_sel_shift) &
+ config->masks->nscale_sel_mask) + 1);
- change_parent(clk, pclk_info->pclk);
-
- spin_lock_irqsave(&clocks_lock, flags);
- if (pclk_info->scalable) {
- val = readl(config->synth_reg);
- div += (val >> config->masks->mscale_sel_shift) &
- config->masks->mscale_sel_mask;
- div *= 1 << (((val >> config->masks->nscale_sel_shift) &
- config->masks->nscale_sel_mask) + 1);
- }
+ if (!div)
+ return -EINVAL;
clk->rate = (unsigned long)clk->pclk->rate / div;
- spin_unlock_irqrestore(&clocks_lock, flags);
+ return 0;
+}
+
+/* Configures new clock rate of gptiliary synthesizers used by: UART, FIRDA*/
+int gpt_clk_set_rate(struct clk *clk, unsigned long desired_rate)
+{
+ struct gpt_rate_tbl *tbls = clk->rate_config.tbls;
+ struct gpt_clk_config *config = clk->private_data;
+ unsigned long val, rate;
+ int i;
+
+ i = round_rate_index(clk, desired_rate, &rate);
+ if (i < 0)
+ return i;
+
+ val = readl(config->synth_reg) & ~(config->masks->mscale_sel_mask <<
+ config->masks->mscale_sel_shift);
+ val |= (tbls[i].mscale & config->masks->mscale_sel_mask) <<
+ config->masks->mscale_sel_shift;
+ val &= ~(config->masks->nscale_sel_mask <<
+ config->masks->nscale_sel_shift);
+ val |= (tbls[i].nscale & config->masks->nscale_sel_mask) <<
+ config->masks->nscale_sel_shift;
+ writel(val, config->synth_reg);
+
+ clk->rate = rate;
+
+ return 0;
+}
+
+/*
+ * Calculates clcd clk rate for different values of div
+ *
+ * Fout from synthesizer can be given from below equation:
+ * Fout= Fin/2*div (division factor)
+ * div is 17 bits:-
+ * 0-13 (fractional part)
+ * 14-16 (integer part)
+ * To calculate Fout we left shift val by 14 bits and divide Fin by
+ * complete div (including fractional part) and then right shift the
+ * result by 14 places.
+ */
+unsigned long clcd_calc_rate(struct clk *clk, int index)
+{
+ unsigned long rate = clk->pclk->rate;
+ struct clcd_rate_tbl *tbls = clk->rate_config.tbls;
+
+ rate /= 1000;
+ rate <<= 12;
+ rate /= (2 * tbls[index].div);
+ rate >>= 12;
+ rate *= 1000;
+
+ return rate;
+}
+
+/*
+ * calculates current programmed rate of clcd synthesizer
+ * Fout from synthesizer can be given from below equation:
+ * Fout= Fin/2*div (division factor)
+ * div is 17 bits:-
+ * 0-13 (fractional part)
+ * 14-16 (integer part)
+ * To calculate Fout we left shift val by 14 bits and divide Fin by
+ * complete div (including fractional part) and then right shift the
+ * result by 14 places.
+ */
+int clcd_clk_recalc(struct clk *clk)
+{
+ struct clcd_clk_config *config = clk->private_data;
+ unsigned int div = 1;
+ unsigned long prate;
+ unsigned int val;
+
+ val = readl(config->synth_reg);
+ div = (val >> config->masks->div_factor_shift) &
+ config->masks->div_factor_mask;
+
+ if (!div)
+ return -EINVAL;
+
+ prate = clk->pclk->rate / 1000; /* first level division, make it KHz */
+
+ clk->rate = (((unsigned long)prate << 12) / (2 * div)) >> 12;
+ clk->rate *= 1000;
+ return 0;
+}
+
+/* Configures new clock rate of auxiliary synthesizers used by: UART, FIRDA*/
+int clcd_clk_set_rate(struct clk *clk, unsigned long desired_rate)
+{
+ struct clcd_rate_tbl *tbls = clk->rate_config.tbls;
+ struct clcd_clk_config *config = clk->private_data;
+ unsigned long val, rate;
+ int i;
+
+ i = round_rate_index(clk, desired_rate, &rate);
+ if (i < 0)
+ return i;
+
+ val = readl(config->synth_reg) & ~(config->masks->div_factor_mask <<
+ config->masks->div_factor_shift);
+ val |= (tbls[i].div & config->masks->div_factor_mask) <<
+ config->masks->div_factor_shift;
+ writel(val, config->synth_reg);
+
+ clk->rate = rate;
+
+ return 0;
}
/*
* Used for clocks that always have value as the parent clock divided by a
* fixed divisor
*/
-void follow_parent(struct clk *clk)
+int follow_parent(struct clk *clk)
{
- unsigned long flags;
unsigned int div_factor = (clk->div_factor < 1) ? 1 : clk->div_factor;
- spin_lock_irqsave(&clocks_lock, flags);
clk->rate = clk->pclk->rate/div_factor;
- spin_unlock_irqrestore(&clocks_lock, flags);
+ return 0;
}
/**
@@ -454,5 +863,25 @@ void follow_parent(struct clk *clk)
*/
void recalc_root_clocks(void)
{
- propagate_rate(&root_clks);
+ struct clk *pclk;
+ unsigned long flags;
+ int ret = 0;
+
+ spin_lock_irqsave(&clocks_lock, flags);
+ list_for_each_entry(pclk, &root_clks, sibling) {
+ if (pclk->recalc) {
+ ret = pclk->recalc(pclk);
+ /*
+ * recalc will return error if clk out is not programmed
+ * In this case configure default clock.
+ */
+ if (ret && pclk->set_rate)
+ pclk->set_rate(pclk, 0);
+ }
+ propagate_rate(pclk, 1);
+ /* Enable clks enabled on init, in software view */
+ if (pclk->flags & ENABLED_ON_INIT)
+ do_clk_enable(pclk);
+ }
+ spin_unlock_irqrestore(&clocks_lock, flags);
}
diff --git a/arch/arm/plat-spear/include/plat/clock.h b/arch/arm/plat-spear/include/plat/clock.h
index 863d9e9..5a601d8 100644
--- a/arch/arm/plat-spear/include/plat/clock.h
+++ b/arch/arm/plat-spear/include/plat/clock.h
@@ -21,6 +21,7 @@
/* clk structure flags */
#define ALWAYS_ENABLED (1 << 0) /* clock always enabled */
#define RESET_TO_ENABLE (1 << 1) /* reset register bit to enable clk */
+#define ENABLED_ON_INIT (1 << 2) /* clocks enabled@init */
/**
* struct clkops - clock operations
@@ -35,13 +36,11 @@ struct clkops {
/**
* struct pclk_info - parents info
* @pclk: pointer to parent clk
- * @pclk_mask: value to be written for selecting this parent
- * @scalable: Is parent scalable (1 - YES, 0 - NO)
+ * @pclk_val: value to be written for selecting this parent
*/
struct pclk_info {
struct clk *pclk;
- u8 pclk_mask;
- u8 scalable;
+ u8 pclk_val;
};
/**
@@ -59,6 +58,18 @@ struct pclk_sel {
};
/**
+ * struct rate_config - clk rate configurations
+ * @tbls: array of device specific clk rate tables, in ascending order of rates
+ * @count: size of tbls array
+ * @default_index: default setting when originally disabled
+ */
+struct rate_config {
+ void *tbls;
+ u8 count;
+ u8 default_index;
+};
+
+/**
* struct clk - clock structure
* @usage_count: num of users who enabled this clock
* @flags: flags for clock properties
@@ -67,7 +78,10 @@ struct pclk_sel {
* @en_reg_bit: clk enable/disable bit
* @ops: clk enable/disable ops - generic_clkops selected if NULL
* @recalc: pointer to clock rate recalculate function
- * @div_factor: division factor to parent clock. Only for recalc = follow_parent
+ * @set_rate: pointer to clock set rate function
+ * @calc_rate: pointer to clock get rate function for index
+ * @rate_config: rate configuration information, used by set_rate
+ * @div_factor: division factor to parent clock.
* @pclk: current parent clk
* @pclk_sel: pointer to parent selection structure
* @pclk_sel_shift: register shift for selecting parent of this clock
@@ -82,7 +96,10 @@ struct clk {
void __iomem *en_reg;
u8 en_reg_bit;
const struct clkops *ops;
- void (*recalc) (struct clk *);
+ int (*recalc) (struct clk *);
+ int (*set_rate) (struct clk *, unsigned long rate);
+ unsigned long (*calc_rate)(struct clk *, int index);
+ struct rate_config rate_config;
unsigned int div_factor;
struct clk *pclk;
@@ -115,6 +132,14 @@ struct pll_clk_config {
struct pll_clk_masks *masks;
};
+/* pll clk rate config structure */
+struct pll_rate_tbl {
+ u8 mode;
+ u16 m;
+ u8 n;
+ u8 p;
+};
+
/* ahb and apb bus configuration structure */
struct bus_clk_masks {
u32 mask;
@@ -126,6 +151,11 @@ struct bus_clk_config {
struct bus_clk_masks *masks;
};
+/* ahb and apb clk bus rate config structure */
+struct bus_rate_tbl {
+ u8 div;
+};
+
/* Aux clk configuration structure: applicable to UART and FIRDA */
struct aux_clk_masks {
u32 eq_sel_mask;
@@ -143,6 +173,13 @@ struct aux_clk_config {
struct aux_clk_masks *masks;
};
+/* aux clk rate config structure */
+struct aux_rate_tbl {
+ u16 xscale;
+ u16 yscale;
+ u8 eq;
+};
+
/* GPT clk configuration structure */
struct gpt_clk_masks {
u32 mscale_sel_mask;
@@ -156,15 +193,48 @@ struct gpt_clk_config {
struct gpt_clk_masks *masks;
};
+/* gpt clk rate config structure */
+struct gpt_rate_tbl {
+ u16 mscale;
+ u16 nscale;
+};
+
+/* clcd clk configuration structure */
+struct clcd_synth_masks {
+ u32 div_factor_mask;
+ u32 div_factor_shift;
+};
+
+struct clcd_clk_config {
+ void __iomem *synth_reg;
+ struct clcd_synth_masks *masks;
+};
+
+/* clcd clk rate config structure */
+struct clcd_rate_tbl {
+ u16 div;
+};
+
/* platform specific clock functions */
void clk_register(struct clk_lookup *cl);
void recalc_root_clocks(void);
-/* clock recalc functions */
-void follow_parent(struct clk *clk);
-void pll_clk_recalc(struct clk *clk);
-void bus_clk_recalc(struct clk *clk);
-void gpt_clk_recalc(struct clk *clk);
-void aux_clk_recalc(struct clk *clk);
+/* clock recalc & set rate functions */
+int follow_parent(struct clk *clk);
+unsigned long pll_calc_rate(struct clk *clk, int index);
+int pll_clk_recalc(struct clk *clk);
+int pll_clk_set_rate(struct clk *clk, unsigned long desired_rate);
+unsigned long bus_calc_rate(struct clk *clk, int index);
+int bus_clk_recalc(struct clk *clk);
+int bus_clk_set_rate(struct clk *clk, unsigned long desired_rate);
+unsigned long gpt_calc_rate(struct clk *clk, int index);
+int gpt_clk_recalc(struct clk *clk);
+int gpt_clk_set_rate(struct clk *clk, unsigned long desired_rate);
+unsigned long aux_calc_rate(struct clk *clk, int index);
+int aux_clk_recalc(struct clk *clk);
+int aux_clk_set_rate(struct clk *clk, unsigned long desired_rate);
+unsigned long clcd_calc_rate(struct clk *clk, int index);
+int clcd_clk_recalc(struct clk *clk);
+int clcd_clk_set_rate(struct clk *clk, unsigned long desired_rate);
#endif /* __PLAT_CLOCK_H */
--
1.7.2.2
^ permalink raw reply related [flat|nested] 2+ messages in thread