* analog sound on Mygica X8506
@ 2011-03-06 14:32 Alfredo Jesús Delaiti
0 siblings, 0 replies; only message in thread
From: Alfredo Jesús Delaiti @ 2011-03-06 14:32 UTC (permalink / raw)
To: linux-media
Hi all
First of all, please if I'm on the wrong list tell me which is correct.
I bought a new TV-card "MyGica X8507" if I set it up as DMB-TH Mygica
X8506 "card 22" analog TV I can see but not hear.
Can you help me to configure this card so I can listen?
I hope that soon this support and can also see digital television.
Thanks in advance
____________________________________________________________________
http://www.linuxtv.org/wiki/index.php/Geniatech/MyGica_X8507_PCI-Express_Hybrid_Card
____________________________________________________________________
dmesg
[ 8.769368] Linux video capture interface: v2.00
[ 8.782879] cx23885 driver version 0.0.2 loaded
[ 8.784037] cx23885 0000:02:00.0: PCI INT A -> GSI 19 (level, low) ->
IRQ 19
[ 8.784041] cx23885[0]/0: cx23885_dev_setup() Memory configured for
PCIe bridge type 885
[ 8.784043] cx23885[0]/0: cx23885_init_tsport(portno=1)
[ 8.784223] CORE cx23885[0]: subsystem: 14f1:8502, board: Mygica
X8506 DMB-TH [card=22,insmod option]
[ 8.784226] cx23885[0]/0: cx23885_pci_quirks()
[ 8.784230] cx23885[0]/0: cx23885_dev_setup() tuner_type = 0x4c
tuner_addr = 0x61
[ 8.784233] cx23885[0]/0: cx23885_dev_setup() radio_type = 0x0
radio_addr = 0x0
[ 8.784235] cx23885[0]/0: cx23885_reset()
[ 8.892926] cx23885[0]/0: cx23885_sram_channel_setup() Configuring
channel [VID A]
[ 8.892930] cx23885[0]/0: cx23885_sram_channel_setup() Erasing
channel [ch2]
[ 8.892932] cx23885[0]/0: cx23885_sram_channel_setup() Configuring
channel [TS1 B]
[ 8.892935] cx23885[0]/0: cx23885_sram_channel_setup() Erasing
channel [ch4]
[ 8.892937] cx23885[0]/0: cx23885_sram_channel_setup() Erasing
channel [ch5]
[ 8.892939] cx23885[0]/0: cx23885_sram_channel_setup() Configuring
channel [TS2 C]
[ 8.892953] cx23885[0]/0: cx23885_sram_channel_setup() Erasing
channel [ch7]
[ 8.892955] cx23885[0]/0: cx23885_sram_channel_setup() Erasing
channel [ch8]
[ 8.892957] cx23885[0]/0: cx23885_sram_channel_setup() Erasing
channel [ch9]
[ 9.131075] cx23885[0]: scan bus 0:
[ 9.133467] cx23885[0]: i2c scan: found device @ 0x20 [???]
[ 9.138377] cx23885[0]: i2c scan: found device @ 0x66 [???]
[ 9.144733] cx23885[0]: i2c scan: found device @ 0xa0 [eeprom]
[ 9.144876] cx23885[0]: i2c scan: found device @ 0xa2 [???]
[ 9.146071] cx23885[0]: i2c scan: found device @ 0xa4 [???]
[ 9.146214] cx23885[0]: i2c scan: found device @ 0xa6 [???]
[ 9.146355] cx23885[0]: i2c scan: found device @ 0xa8 [???]
[ 9.146496] cx23885[0]: i2c scan: found device @ 0xaa [???]
[ 9.146637] cx23885[0]: i2c scan: found device @ 0xac [???]
[ 9.146778] cx23885[0]: i2c scan: found device @ 0xae [???]
[ 9.152627] cx23885[0]: scan bus 1:
[ 9.168325] cx23885[0]: i2c scan: found device @ 0xc2
[tuner/mt2131/tda8275/xc5000/xc3028]
[ 9.173738] cx23885[0]: scan bus 2:
[ 9.184143] cx23885[0]: i2c scan: found device @ 0x66 [???]
[ 9.184795] cx23885[0]: i2c scan: found device @ 0x88 [cx25837]
[ 9.185099] cx23885[0]: i2c scan: found device @ 0x98 [???]
[ 9.292405] cx25840 5-0044: cx23885 A/V decoder found @ 0x88 (cx23885[0])
[ 9.302242] cx25840 5-0044: firmware: requesting v4l-cx23885-avcore-01.fw
[ 10.374232] cx25840 5-0044: loaded v4l-cx23885-avcore-01.fw firmware
(16382 bytes)
[ 10.380657] cx23885[0]/0: cx23885_video_register()
[ 10.382438] tuner 4-0061: chip found @ 0xc2 (cx23885[0])
[ 10.553069] xc5000 4-0061: creating new instance
[ 10.553766] xc5000: Successfully identified at address 0x61
[ 10.553768] xc5000: Firmware has not been loaded previously
[ 10.553770] cx23885[0]/0: cx23885_vdev_init()
[ 10.553828] cx23885[0]/0: registered device video1 [v4l2]
[ 10.553831] cx23885[0]/0: cx23885_set_tvnorm(norm = 0x00001000) name:
[NTSC-M]
[ 10.559271] xc5000: waiting for firmware upload
(dvb-fe-xc5000-1.6.114.fw)...
[ 10.559274] cx23885 0000:02:00.0: firmware: requesting
dvb-fe-xc5000-1.6.114.fw
[ 10.692589] xc5000: firmware read 12401 bytes.
[ 10.692591] xc5000: firmware uploading...
[ 12.066004] xc5000: firmware upload complete...
[ 12.707015] cx23885[0]/0: cx23885_set_control() calling
cx25840(VIDIOC_S_CTRL) (disabled - no action)
[ 12.707017] cx23885[0]/0: cx23885_set_control() calling
cx25840(VIDIOC_S_CTRL) (disabled - no action)
[ 12.707019] cx23885[0]/0: cx23885_set_control() calling
cx25840(VIDIOC_S_CTRL) (disabled - no action)
[ 12.707022] cx23885[0]/0: cx23885_set_control() calling
cx25840(VIDIOC_S_CTRL) (disabled - no action)
[ 12.707024] cx23885[0]/0: cx23885_set_control() calling
cx25840(VIDIOC_S_CTRL) (disabled - no action)
[ 12.707026] cx23885[0]/0: cx23885_set_control() calling
cx25840(VIDIOC_S_CTRL) (disabled - no action)
[ 12.707029] cx23885[0]/0: cx23885_video_mux() video_mux: 0 [vmux=2,
gpio=0x0,0x0,0x0,0x0]
[ 12.711091] cx23885_dvb_register() allocating 1 frontend(s)
[ 12.711094] cx23885[0]: cx23885 based dvb card
[ 12.750805] xc5000 4-0061: attaching existing instance
[ 12.751535] xc5000: Successfully identified at address 0x61
[ 12.751536] xc5000: Firmware has been loaded previously
[ 12.751540] DVB: registering new adapter (cx23885[0])
[ 12.751544] DVB: registering adapter 0 frontend 0 (Legend Silicon
LGS8913/LGS8GXX DMB-TH)...
[ 12.751815] cx23885_dev_checkrevision() Hardware revision = 0xb0
[ 12.751824] cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 19,
latency: 0, mmio: 0xfd600000
[ 12.751831] cx23885 0000:02:00.0: setting latency timer to 64
[ 12.751836] IRQ 19/cx23885[0]: IRQF_DISABLED is not guaranteed on
shared IRQs
[ 12.754419] cx23885[0]/0: open dev=video1 radio=0 type=vid-cap
[ 12.754424] cx23885[0]/0: post videobuf_queue_init()
[ 19.342718] cx23885[0]/0: open dev=video1 radio=0 type=vid-cap
[ 19.342723] cx23885[0]/0: post videobuf_queue_init()
____________________________________________________________________
lspci -vvvnn
02:00.0 Multimedia video controller [0400]: Conexant Systems, Inc.
CX23885 PCI Video and Audio Decoder [14f1:8852] (rev 02)
Subsystem: Conexant Systems, Inc. Device [14f1:8502]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fd600000 (64-bit, non-prefetchable) [size=2M]
Capabilities: [40] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0 <2us, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Vital Product Data
Product Name: "
End
Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt-
UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap-
ChkEn-
Capabilities: [200 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32+ WRR64+ WRR128-
Ctrl: ArbSelect=WRR64
Status: InProgress-
Port Arbitration Table [240] <?>
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: cx23885
Thanks in advance
--
Dona tu voz
http://www.voxforge.org/es
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2011-03-06 14:32 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-03-06 14:32 analog sound on Mygica X8506 Alfredo Jesús Delaiti
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.