openssl-native 1.0.0d fails to build

openssl-native 1.0.0d fails to build

[Robert Schuster]

[-- Attachment #1: Type: text/plain, Size: 2677 bytes --]

Hi,
I'm building angstrom-2010.x for omapp4430-panda on an amd64 box running
Ubunutu 10.04. While building the console-image it gets to the point
where openssl-native has to be compiled and there is see strange errors.
do_configure completes without error but the log.do_configure looks like
this:

Configuring for linux-x86_64
    no-gmp          [default]  OPENSSL_NO_GMP (skip dir)
    no-jpake        [experimental] OPENSSL_NO_JPAKE (skip dir)
    no-krb5         [krb5-flavor not specified] OPENSSL_NO_KRB5
    no-md2          [default]  OPENSSL_NO_MD2 (skip dir)
    no-rc5          [default]  OPENSSL_NO_RC5 (skip dir)
    no-rfc3779      [default]  OPENSSL_NO_RFC3779 (skip dir)
    no-store        [experimental] OPENSSL_NO_STORE (skip dir)
    no-zlib         [default]
    no-zlib-dynamic [default]
IsMK1MF=0
CC            =gcc
CFLAG         =-fPIC -DOPENSSL_PIC -DOPENSSL_THREADS -D_REENTRANT
-DDSO_DLFCN -DHAVE_DLFCN_H -DL_ENDIAN 	-DTERMIO   -Wall
-Wa,--noexecstack -DOPENSSL_IA32_SSE2 -DOPENSSL_BN_ASM_MONT -DSHA1_ASM
-DSHA256_ASM -DSHA512_ASM -DMD5_ASM -DAES_ASM -DWHIRLPOOL_ASM
EX_LIBS       =-ldl
CPUID_OBJ     =x86_64cpuid.o
BN_ASM        =x86_64-gcc.o x86_64-mont.o
DES_ENC       =des_enc.o fcrypt_b.o
AES_ENC       =aes-x86_64.o
BF_ENC        =bf_enc.o
CAST_ENC      =c_enc.o
RC4_ENC       =rc4-x86_64.o
RC5_ENC       =rc5_enc.o
MD5_OBJ_ASM   =md5-x86_64.o
SHA1_OBJ_ASM  =sha1-x86_64.o sha256-x86_64.o sha512-x86_64.o
RMD160_OBJ_ASM=
CMLL_ENC=     =cmll-x86_64.o cmll_misc.o
PROCESSOR     =
RANLIB        =ranlib
ARFLAGS       =
PERL          =/home/rschus/oe/panda/tmp/sysroots/x86_64-linux/usr/bin/perl
SIXTY_FOUR_BIT_LONG mode
DES_UNROLL used
DES_INT used
RC4_CHUNK is unsigned long
Makefile is older than Makefile.org, Configure or config.
Reconfigure the source tree (via './config' or 'perl Configure'), please.
make: *** [Makefile] Error 1

Since the error at the end does not show up in bitbake the build
continues (= it goes into do_compile). However the compilation stops
immediately and the log only contains this output:

NOTE: make -e MAKEFLAGS=
Makefile is older than Makefile.org, Configure or config.
Reconfigure the source tree (via './config' or 'perl Configure'), please.
make: *** [Makefile] Error 1
FATAL: oe_runmake failed
ERROR: Function do_compile failed

Manual workaround is to go into the workdir and run 'touch Makefile'.
After that the build continues just fine.

I did not investigate the problem further yet but would do so if nobody
has an idea of what the problem in the recipe might be. Does this
problem occur on other's machines too?

Regards,
Robert


[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 270 bytes --]