From: "Jim Schutt" <jaschut-4OHPYypu0djtX7QSmKvirg@public.gmane.org>
To: Jim Schutt <jaschut-4OHPYypu0djtX7QSmKvirg@public.gmane.org>
Cc: Or Gerlitz <ogerlitz-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>,
Roland Dreier <roland-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>,
Bob Pearson
<rpearson-klaOcWyJdxkshyMvu7JE4pqQE7yCjDx5@public.gmane.org>,
Or Gerlitz <or.gerlitz-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>,
linux-rdma <linux-rdma-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>,
Vladimir Sokolovsky
<vlad-VPRAkNaXOzVS1MOuV/RT9w@public.gmane.org>,
Alex Netes <alexne-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
Subject: Re: [PATCH] mlx4: allow for 4K mtu configuration of IB ports
Date: Thu, 26 May 2011 08:30:17 -0600 [thread overview]
Message-ID: <4DDE63F9.8060502@sandia.gov> (raw)
In-Reply-To: <17495_1306419903_p4QEMqSb018281_4DDE6291.1090809-4OHPYypu0djtX7QSmKvirg@public.gmane.org>
Jim Schutt wrote:
> Or Gerlitz wrote:
>> Roland Dreier wrote:
>>> Bob Pearson <rpearson-klaOcWyJdxkshyMvu7JE4pqQE7yCjDx5@public.gmane.org> wrote:
>>>> With lash+mesh redsky required 6-7 VLs to wire up without deadlocks.
>>>> I think
>>>> that Jim's version uses 8 SLs but only 2VLs to work.
>>>> If someone was using a torus and also wanted to support QOS and also
>>>> wanted
>>>> to separate multicast and management on a separate VL to be
>>>> absolutely sure
>>>> that there is no possibility of a deadlock you might end up with
>>>> #QOS * 2 +
>>>> 1 which would be 5 using the current algorithm.
>>
>>> But again you don't need all those VLs on the HCAs' links, do you?
>>
>> Jason Gunthorpe wrote:
>>> Routing algorithms only need VLs on interswitch links, not on HCA to
>>> switch links. The only use of the HCA to switch VLs is for QoS. Mesh
>>> topologies can usually be routed with only two VLs, but you need alot
>>> of SLs to make that work.
>>
>> Bob, Jim, Alex
>>
>> I wasn't sure if the SL-to-VL mapping done by open SM is dictated by
>> the directives @ the user config file or if the routing algorithm is
>> "VL aware" but the routing engine? if the latter, do interswitch links
>> use different mapping vs. HCA - switch links?
>
> FWIW, the torus-2QoS routing engine uses VL bit 0 for torus deadlock
> avoidance, VL bit 1 to route around a missing switch without deadlocks,
> and VL bit 2 to provide two QoS levels. It needs the port dependence
> of the SL2VL maps to do this in switches.
>
> The interswitch and HCAs use the same mapping, but only VL bit 2
> is needed on HCAs, to provide the QoS levels.
It occurred to me as soon I sent the above that there's no
good reason to insist that the VL usage is the same for both
interswitch links, and switch-CA links.
Do I need to change this?
-- Jim
>
> I chose that bit usage because it seemed the proper ordering of
> capabilities if there are fewer than 8 data VLs available - basic
> deadlock avoidance is most important; some QoS is nice to have but
> not that useful if the fabric can deadlock.
>
> Is that what you were asking, at least WRT. torus-2QoS?
>
> -- Jim
>
>>
>> Or.
>>
>>
>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-rdma" in
> the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-rdma" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2011-05-26 14:30 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-05-25 12:10 [PATCH] mlx4: allow for 4K mtu configuration of IB ports Or Gerlitz
[not found] ` <alpine.LRH.2.00.1105251507140.16147-VYr5/9ddeaGSIdy2EShu12Xnswh1EIUO@public.gmane.org>
2011-05-25 16:13 ` Roland Dreier
[not found] ` <BANLkTi=bKdVXm+f+HVeg2tBzT4RBJDCN_w-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2011-05-25 21:05 ` Or Gerlitz
[not found] ` <BANLkTinDCbPXi8zS46wcVW_Yn0fxzbSikw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2011-05-25 21:27 ` Roland Dreier
[not found] ` <BANLkTikrJ_3f+LwN_R=-AcwCde-KdHJhOQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2011-05-25 21:46 ` Or Gerlitz
[not found] ` <BANLkTinT5OJdP38Xq=PCtx1wgxDhjVfndA-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2011-05-25 22:07 ` Jason Gunthorpe
2011-05-25 22:10 ` Roland Dreier
[not found] ` <BANLkTi=NkZQX2JFa99qkVpLAchRjNoYOhg-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2011-05-26 6:24 ` Or Gerlitz
[not found] ` <4DDDF212.4080700-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
2011-05-26 15:53 ` Roland Dreier
[not found] ` <BANLkTimrm7bqTT8qAzxdf9tsJuv7+NPO+g-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2011-05-30 22:12 ` Or Gerlitz
2011-05-25 22:19 ` Bob Pearson
2011-05-25 23:14 ` Roland Dreier
[not found] ` <BANLkTikLeWHYLKrX8O=syt-Q+b6LP2PCtw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2011-05-26 6:18 ` Or Gerlitz
[not found] ` <4DDDF0B1.6090305-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
2011-05-26 14:24 ` Jim Schutt
[not found] ` <17495_1306419903_p4QEMqSb018281_4DDE6291.1090809@sandia.gov>
[not found] ` <17495_1306419903_p4QEMqSb018281_4DDE6291.1090809-4OHPYypu0djtX7QSmKvirg@public.gmane.org>
2011-05-26 14:30 ` Jim Schutt [this message]
[not found] ` <4DDE63F9.8060502-4OHPYypu0djtX7QSmKvirg@public.gmane.org>
2011-05-26 15:56 ` Roland Dreier
[not found] ` <BANLkTimGioibPTUYV046ObOPhHntHxx72w-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2011-05-30 22:07 ` Or Gerlitz
[not found] ` <BANLkTinK+YHUyF4ThHQAwFeZ4FNswpY-tw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2011-05-31 16:11 ` Jim Schutt
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4DDE63F9.8060502@sandia.gov \
--to=jaschut-4ohpyypu0djtx7qsmkvirg@public.gmane.org \
--cc=alexne-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org \
--cc=linux-rdma-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=ogerlitz-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org \
--cc=or.gerlitz-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \
--cc=roland-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
--cc=rpearson-klaOcWyJdxkshyMvu7JE4pqQE7yCjDx5@public.gmane.org \
--cc=vlad-VPRAkNaXOzVS1MOuV/RT9w@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.