* [PULL][linux-yocto] beagleboard: sync with meta-ti linux-omap_2.6.37
@ 2011-06-17 23:18 Darren Hart
2011-06-18 8:11 ` Koen Kooi
0 siblings, 1 reply; 9+ messages in thread
From: Darren Hart @ 2011-06-17 23:18 UTC (permalink / raw)
To: yocto, bruce.ashfield; +Cc: Darren Hart
From: Darren Hart <dvhart@linux.intel.com>
The following commits have been pulled in from the meta-ti linux-omap_2.6.37
recipe, with the exception of:
USB: ehci: remove structure packing from ehci_def
which hails from mainline and should be applied to yocto/base, while the rest
should be applied to yocto/standard/beagleboard.
Fixes [YOCTO #764]
Fixes [YOCTO #765]
Fixes [YOCTO #767]
This brings linux-yocto in sync with the meta-ti linux-omap_2.6.37 recipe and
significantly improves Beagleboard support in linux-yocto. As there are 115
patches in total, and none of them are new, I have omitted them from the email.
The following changes since commit 9cb5c3fb1634e541cacceeb8c8cabe88afa5b080:
Merge branch 'yocto/standard/base' into yocto/standard/beagleboard (2011-06-06 10:35:20 -0400)
are available in the git repository at:
git://git.yoctoproject.org/linux-yocto-2.6.37-contrib dvhart/yocto/standard/beagleboard
http://git.yoctoproject.org/cgit.cgi/linux-yocto-2.6.37-contrib/log/?h=dvhart/yocto/standard/beagleboard
Alexander Holler (1):
arm: omap3: beagle: Ensure msecure is mux'd to be able to set the RTC
Antti Koskipaa (1):
v4l: v4l2_subdev userspace crop API
Arik Nemtsov (1):
wl12xx: Read MAC address from NVS file on HW startup
Darren Hart (2):
board-omap3beagle: whitespace cleanup
board-omap3beagle: allow for building without wl1271
Eliad Peller (1):
wl1271: set wl->vif only if add_interface succeeded.
Florian Westphal (1):
bridge: stp: ensure mac header is set
Jesper Juhl (1):
ISDN, Gigaset: Fix memory leak in do_disconnect_req()
Juuso Oikarinen (1):
wl12xx: Unset bssid filter, ssid and bssid from firmware on disassoc
Kevin Hilman (1):
OMAP: CPUfreq: ensure policy is fully initialized
Koen Kooi (10):
omap3: beaglexm: fix DVI reset GPIO
omap3: beaglexm: fix power on of DVI
ARM: OMAP: beagleboard: Add infrastructure to do fixups based on
expansionboard name passed by u-boot
ARM: OMAP: beagleboard: pre-export GPIOs to userspace when using a
Tincantools trainerboard
modedb.c: add proper 720p60 mode
ARM: OMAP: add omap_rev_* macros
omap3: beagleboard: add WIP support for beagleboardtoys WL12xx board
beagleboard: hack in support from xM rev C
omap3: allow 1GHz mpurates
BeagleBoard: Adjust USER button pin for xM
Laurent Pinchart (35):
v4l: Share code between video_usercopy and video_ioctl2
v4l: subdev: Don't require core operations
v4l: subdev: Merge v4l2_i2c_new_subdev_cfg and v4l2_i2c_new_subdev
v4l: subdev: Add device node support
v4l: subdev: Uninline the v4l2_subdev_init function
v4l: subdev: Control ioctls support
media: Media device node support
media: Media device
media: Entities, pads and links
media: Entity use count
media: Media device information query
media: Entities, pads and links enumeration
media: Links setup
media: Pipelines and media streams
v4l: Add a media_device pointer to the v4l2_device structure
v4l: Make video_device inherit from media_entity
v4l: Make v4l2_subdev inherit from media_entity
v4l: Move the media/v4l2-mediabus.h header to include/linux
v4l: Replace enums with fixed-sized fields in public structure
v4l: Rename V4L2_MBUS_FMT_GREY8_1X8 to V4L2_MBUS_FMT_Y8_1X8
v4l: Group media bus pixel codes by types and sort them
alphabetically
v4l: subdev: Add a new file operations class
v4l: v4l2_subdev pad-level operations
v4l: v4l2_subdev userspace format API
v4l: v4l2_subdev userspace frame interval API
v4l: subdev: Generic ioctl support
v4l: Add subdev sensor g_skip_frames operation
v4l: Include linux/videodev2.h in media/v4l2-ctrls.h
v4l: Fix a use-before-set in the control framework
v4l: Add 8-bit YUYV on 16-bit bus and SGRBG10 media bus pixel codes
v4l: Add remaining RAW10 patterns w DPCM pixel code variants
v4l: Add missing 12 bits bayer media bus formats
v4l: Add 12 bits bayer pixel formats
omap3: Add function to register omap3isp platform device structure
OMAP3 ISP driver
Lennert Buytenhek (1):
ARM: pxa: PXA_ESERIES depends on FB_W100.
Manjunatha Halli (7):
drivers:media:radio: wl128x: FM Driver common header file
drivers:media:radio: wl128x: FM Driver V4L2 sources
drivers:media:radio: wl128x: FM Driver Common sources
drivers:media:radio: wl128x: FM driver RX sources
drivers:media:radio: wl128x: FM driver TX sources
drivers:media:radio: wl128x: Kconfig & Makefile for wl128x driver
drivers:media:radio: Update Kconfig and Makefile for wl128x FM
driver.
Nishanth Menon (2):
omap3|4: opp: make omapx_opp_init non-static
OMAP3: beagle xm: enable upto 1GHz OPP
Pavan Savoy (2):
drivers:misc:ti-st: change protocol parse logic
Bluetooth: btwilink driver
Peter 'p2' De Schrijver (1):
OMAP: CPUfreq: ensure driver initializes after cpufreq framework and
governors
Rabin Vincent (1):
USB: ehci: remove structure packing from ehci_def
Rajendra Nayak (1):
OMAP3 PM: CPUFreq driver for OMAP3
Robert Nelson (2):
omap: Beagle: detect new xM revision B
xM audio fix from Ashok
Sakari Ailus (2):
v4l: subdev: Events support
media: Entity graph traversal
Sanjeev Premi (1):
omap3: Add basic support for 720MHz part
Sergio Aguirre (2):
omap3: Remove unusued ISP CBUFF resource
omap2: Fix camera resources for multiomap
Shahar Levi (3):
wl1271: 11n Support, Add Definitions
wl1271: 11n Support, ACX Commands
wl1271: 11n Support, functionality and configuration ability
Silesh C V (1):
OMAP: PM: CPUFREQ: Fix conditional compilation
Stanimir Varbanov (1):
v4l: Create v4l2 subdev file handle structure
Steve Sakoman (18):
mmc: don't display single block read console messages
MTD: silence ecc errors on mtdblock0
OMAP: DSS2: enable hsclk in dsi_pll_init for OMAP36XX
drivers: net: smsc911x: return ENODEV if device is not found
drivers: input: touchscreen: ads7846: return ENODEV if device is not
found
ASoC: enable audio capture by default for twl4030
MFD: enable madc clock
MFD: add twl4030 madc driver
ARM: OMAP: Add twl4030 madc support to Overo
ARM: OMAP: Add twl4030 madc support to Beagle
OMAP: DSS2: Add support for Samsung LTE430WQ-F0C panel
OMAP: DSS2: Add support for LG Philips LB035Q02 panel
OMAP: DSS2: add bootarg for selecting svideo or composite for tv
output
ARM: OMAP2: mmc-twl4030: move clock input selection prior to vcc test
RTC: add support for backup battery recharge
ARM: OMAP: automatically set musb mode in platform data based on
CONFIG options
OMAP: DSS2: check for both cpu type and revision, rather than just
revision
OMAP: DSS2: Add DSS2 support for Overo
Thara Gopinath (13):
OMAP3: PM: Adding T2 enabling of smartreflex
OMAP: Introduce a user list for each voltage domain instance in the
voltage driver.
OMAP: Introduce API in the OPP layer to find the opp entry
corresponding to a voltage.
OMAP: Introduce API to register a device with a voltagedomain
OMAP: Introduce device specific set rate and get rate in omap_device
structure
OMAP: Voltage layer changes to support DVFS.
OMAP: Introduce dependent voltage domain support.
OMAP: Introduce device scale
OMAP: Disable smartreflex across DVFS
OMAP3: Introduce custom set rate and get rate APIs for scalable
devices
OMAP3: Update cpufreq driver to use the new set_rate API
OMAP3: Introduce voltage domain info in the hwmod structures.
OMAP3: Add voltage dependency table for VDD1.
Thomas Weber (1):
OMAP: Enable Magic SysRq on serial console ttyOx
Tuukka Toivonen (1):
ARM: OMAP3: Update Camera ISP definitions for OMAP3630
Documentation/ABI/testing/sysfs-bus-media | 6 +
Documentation/DocBook/Makefile | 5 +-
Documentation/DocBook/media-entities.tmpl | 50 +
Documentation/DocBook/media.tmpl | 3 +
Documentation/DocBook/v4l/dev-subdev.xml | 307 +++
Documentation/DocBook/v4l/media-controller.xml | 89 +
Documentation/DocBook/v4l/media-func-close.xml | 59 +
Documentation/DocBook/v4l/media-func-ioctl.xml | 116 +
Documentation/DocBook/v4l/media-func-open.xml | 94 +
.../DocBook/v4l/media-ioc-device-info.xml | 133 ++
.../DocBook/v4l/media-ioc-enum-entities.xml | 308 +++
Documentation/DocBook/v4l/media-ioc-enum-links.xml | 207 ++
Documentation/DocBook/v4l/media-ioc-setup-link.xml | 93 +
Documentation/DocBook/v4l/subdev-formats.xml | 2467 ++++++++++++++++++++
Documentation/DocBook/v4l/v4l2.xml | 7 +
Documentation/DocBook/v4l/vidioc-streamon.xml | 9 +
.../v4l/vidioc-subdev-enum-frame-interval.xml | 146 ++
.../DocBook/v4l/vidioc-subdev-enum-frame-size.xml | 148 ++
.../DocBook/v4l/vidioc-subdev-enum-mbus-code.xml | 113 +
Documentation/DocBook/v4l/vidioc-subdev-g-crop.xml | 149 ++
Documentation/DocBook/v4l/vidioc-subdev-g-fmt.xml | 174 ++
.../DocBook/v4l/vidioc-subdev-g-frame-interval.xml | 135 ++
Documentation/media-framework.txt | 353 +++
Documentation/video4linux/v4l2-framework.txt | 129 +-
arch/arm/mach-omap2/board-omap3beagle.c | 409 ++++-
arch/arm/mach-omap2/board-overo.c | 247 ++-
arch/arm/mach-omap2/clock.h | 14 +-
arch/arm/mach-omap2/clock34xx.c | 2 +
arch/arm/mach-omap2/control.h | 7 +
arch/arm/mach-omap2/devices.c | 64 +-
arch/arm/mach-omap2/devices.h | 17 +
arch/arm/mach-omap2/hsmmc.c | 14 +-
arch/arm/mach-omap2/id.c | 10 +
arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 3 +
arch/arm/mach-omap2/omap_twl.c | 16 +
arch/arm/mach-omap2/opp3xxx_data.c | 66 +-
arch/arm/mach-omap2/opp4xxx_data.c | 3 +-
arch/arm/mach-omap2/pm.c | 110 +
arch/arm/mach-omap2/voltage.c | 369 +++-
arch/arm/mach-pxa/Kconfig | 1 +
arch/arm/plat-omap/clock.c | 2 +-
arch/arm/plat-omap/cpu-omap.c | 38 +-
arch/arm/plat-omap/include/plat/cpu.h | 57 +
arch/arm/plat-omap/include/plat/omap34xx.h | 16 +-
arch/arm/plat-omap/include/plat/omap_device.h | 12 +-
arch/arm/plat-omap/include/plat/voltage.h | 20 +
arch/arm/plat-omap/omap_device.c | 139 ++
block/blk-core.c | 7 +-
drivers/base/power/opp.c | 28 +
drivers/bluetooth/Kconfig | 10 +
drivers/bluetooth/Makefile | 1 +
drivers/bluetooth/btwilink.c | 397 ++++
drivers/input/touchscreen/ads7846.c | 13 +-
drivers/isdn/gigaset/capi.c | 1 +
drivers/media/Kconfig | 22 +
drivers/media/Makefile | 10 +-
drivers/media/media-device.c | 382 +++
drivers/media/media-devnode.c | 321 +++
drivers/media/media-entity.c | 536 +++++
drivers/media/radio/Kconfig | 3 +
drivers/media/radio/Makefile | 1 +
drivers/media/radio/radio-si4713.c | 2 +-
drivers/media/radio/wl128x/Kconfig | 17 +
drivers/media/radio/wl128x/Makefile | 6 +
drivers/media/radio/wl128x/fmdrv.h | 244 ++
drivers/media/radio/wl128x/fmdrv_common.c | 1677 +++++++++++++
drivers/media/radio/wl128x/fmdrv_common.h | 402 ++++
drivers/media/radio/wl128x/fmdrv_rx.c | 847 +++++++
drivers/media/radio/wl128x/fmdrv_rx.h | 59 +
drivers/media/radio/wl128x/fmdrv_tx.c | 425 ++++
drivers/media/radio/wl128x/fmdrv_tx.h | 37 +
drivers/media/radio/wl128x/fmdrv_v4l2.c | 580 +++++
drivers/media/radio/wl128x/fmdrv_v4l2.h | 33 +
drivers/media/video/Kconfig | 13 +
drivers/media/video/Makefile | 4 +-
drivers/media/video/cafe_ccic.c | 11 +-
drivers/media/video/davinci/vpfe_capture.c | 2 +-
drivers/media/video/davinci/vpif_capture.c | 2 +-
drivers/media/video/davinci/vpif_display.c | 2 +-
drivers/media/video/isp/Makefile | 13 +
drivers/media/video/isp/cfa_coef_table.h | 601 +++++
drivers/media/video/isp/gamma_table.h | 90 +
drivers/media/video/isp/isp.c | 2221 ++++++++++++++++++
drivers/media/video/isp/isp.h | 427 ++++
drivers/media/video/isp/ispccdc.c | 2280 ++++++++++++++++++
drivers/media/video/isp/ispccdc.h | 223 ++
drivers/media/video/isp/ispccp2.c | 1189 ++++++++++
drivers/media/video/isp/ispccp2.h | 101 +
drivers/media/video/isp/ispcsi2.c | 1332 +++++++++++
drivers/media/video/isp/ispcsi2.h | 169 ++
drivers/media/video/isp/ispcsiphy.c | 247 ++
drivers/media/video/isp/ispcsiphy.h | 74 +
drivers/media/video/isp/isph3a.h | 117 +
drivers/media/video/isp/isph3a_aewb.c | 374 +++
drivers/media/video/isp/isph3a_af.c | 429 ++++
drivers/media/video/isp/isphist.c | 520 ++++
drivers/media/video/isp/isphist.h | 40 +
drivers/media/video/isp/isppreview.c | 2120 +++++++++++++++++
drivers/media/video/isp/isppreview.h | 214 ++
drivers/media/video/isp/ispqueue.c | 1136 +++++++++
drivers/media/video/isp/ispqueue.h | 185 ++
drivers/media/video/isp/ispreg.h | 1589 +++++++++++++
drivers/media/video/isp/ispresizer.c | 1710 ++++++++++++++
drivers/media/video/isp/ispresizer.h | 150 ++
drivers/media/video/isp/ispstat.c | 1100 +++++++++
drivers/media/video/isp/ispstat.h | 169 ++
drivers/media/video/isp/ispvideo.c | 1264 ++++++++++
drivers/media/video/isp/ispvideo.h | 202 ++
drivers/media/video/isp/luma_enhance_table.h | 154 ++
drivers/media/video/isp/noise_filter_table.h | 90 +
drivers/media/video/ivtv/ivtv-i2c.c | 11 +-
drivers/media/video/mt9m001.c | 2 +-
drivers/media/video/mt9v022.c | 4 +-
drivers/media/video/ov6650.c | 10 +-
drivers/media/video/s5p-fimc/fimc-capture.c | 2 +-
drivers/media/video/sh_mobile_csi2.c | 6 +-
drivers/media/video/sh_vou.c | 2 +-
drivers/media/video/soc_camera.c | 2 +-
drivers/media/video/soc_mediabus.c | 2 +-
drivers/media/video/v4l2-common.c | 22 +-
drivers/media/video/v4l2-ctrls.c | 2 +-
drivers/media/video/v4l2-dev.c | 76 +-
drivers/media/video/v4l2-device.c | 66 +-
drivers/media/video/v4l2-ioctl.c | 216 +--
drivers/media/video/v4l2-subdev.c | 346 +++
drivers/mfd/Kconfig | 21 +
drivers/mfd/Makefile | 1 +
drivers/mfd/twl-core.c | 8 +
drivers/mfd/twl4030-madc.c | 537 +++++
drivers/misc/ti-st/st_core.c | 355 +--
drivers/misc/ti-st/st_kim.c | 56 +-
drivers/mmc/card/block.c | 4 +-
drivers/mtd/nand/nand_ecc.c | 2 +-
drivers/net/smsc911x.c | 4 +-
drivers/net/wireless/wl12xx/Kconfig | 10 +
drivers/net/wireless/wl12xx/wl1271.h | 11 +-
drivers/net/wireless/wl12xx/wl1271_acx.c | 83 +
drivers/net/wireless/wl12xx/wl1271_acx.h | 86 +
drivers/net/wireless/wl12xx/wl1271_main.c | 161 +-
drivers/net/wireless/wl12xx/wl1271_rx.c | 6 +
drivers/net/wireless/wl12xx/wl1271_tx.c | 11 +
drivers/rtc/rtc-twl.c | 25 +
drivers/serial/omap-serial.c | 4 +
drivers/video/modedb.c | 4 +
drivers/video/omap2/displays/Kconfig | 12 +
drivers/video/omap2/displays/Makefile | 2 +
.../omap2/displays/panel-lgphilips-lb035q02.c | 244 ++
.../omap2/displays/panel-samsung-lte430wq-f0c.c | 154 ++
drivers/video/omap2/dss/dispc.c | 4 +-
drivers/video/omap2/dss/dpi.c | 7 +-
drivers/video/omap2/dss/venc.c | 22 +
drivers/video/omap2/omapfb/omapfb-main.c | 10 +-
fs/buffer.c | 3 +-
include/linux/Kbuild | 4 +
include/linux/i2c/twl.h | 1 +
include/linux/i2c/twl4030-madc.h | 130 +
include/linux/media.h | 132 ++
include/linux/omap3isp.h | 631 +++++
include/linux/opp.h | 8 +
include/linux/ti_wilink_st.h | 40 +-
include/linux/usb/ehci_def.h | 6 +-
include/linux/v4l2-mediabus.h | 108 +
include/linux/v4l2-subdev.h | 141 ++
include/linux/videodev2.h | 4 +
include/media/media-device.h | 95 +
include/media/media-devnode.h | 97 +
include/media/media-entity.h | 147 ++
include/media/soc_mediabus.h | 3 +-
include/media/v4l2-common.h | 18 +-
include/media/v4l2-ctrls.h | 1 +
include/media/v4l2-dev.h | 25 +-
include/media/v4l2-device.h | 4 +
include/media/v4l2-ioctl.h | 3 +
include/media/v4l2-mediabus.h | 61 +-
include/media/v4l2-subdev.h | 120 +-
net/bridge/br_stp_bpdu.c | 2 +
sound/soc/codecs/twl4030.c | 4 +-
sound/soc/omap/omap-mcbsp.c | 3 +
178 files changed, 37220 insertions(+), 745 deletions(-)
create mode 100644 Documentation/ABI/testing/sysfs-bus-media
create mode 100644 Documentation/DocBook/v4l/dev-subdev.xml
create mode 100644 Documentation/DocBook/v4l/media-controller.xml
create mode 100644 Documentation/DocBook/v4l/media-func-close.xml
create mode 100644 Documentation/DocBook/v4l/media-func-ioctl.xml
create mode 100644 Documentation/DocBook/v4l/media-func-open.xml
create mode 100644 Documentation/DocBook/v4l/media-ioc-device-info.xml
create mode 100644 Documentation/DocBook/v4l/media-ioc-enum-entities.xml
create mode 100644 Documentation/DocBook/v4l/media-ioc-enum-links.xml
create mode 100644 Documentation/DocBook/v4l/media-ioc-setup-link.xml
create mode 100644 Documentation/DocBook/v4l/subdev-formats.xml
create mode 100644 Documentation/DocBook/v4l/vidioc-subdev-enum-frame-interval.xml
create mode 100644 Documentation/DocBook/v4l/vidioc-subdev-enum-frame-size.xml
create mode 100644 Documentation/DocBook/v4l/vidioc-subdev-enum-mbus-code.xml
create mode 100644 Documentation/DocBook/v4l/vidioc-subdev-g-crop.xml
create mode 100644 Documentation/DocBook/v4l/vidioc-subdev-g-fmt.xml
create mode 100644 Documentation/DocBook/v4l/vidioc-subdev-g-frame-interval.xml
create mode 100644 Documentation/media-framework.txt
create mode 100644 arch/arm/mach-omap2/devices.h
create mode 100644 drivers/bluetooth/btwilink.c
create mode 100644 drivers/media/media-device.c
create mode 100644 drivers/media/media-devnode.c
create mode 100644 drivers/media/media-entity.c
create mode 100644 drivers/media/radio/wl128x/Kconfig
create mode 100644 drivers/media/radio/wl128x/Makefile
create mode 100644 drivers/media/radio/wl128x/fmdrv.h
create mode 100644 drivers/media/radio/wl128x/fmdrv_common.c
create mode 100644 drivers/media/radio/wl128x/fmdrv_common.h
create mode 100644 drivers/media/radio/wl128x/fmdrv_rx.c
create mode 100644 drivers/media/radio/wl128x/fmdrv_rx.h
create mode 100644 drivers/media/radio/wl128x/fmdrv_tx.c
create mode 100644 drivers/media/radio/wl128x/fmdrv_tx.h
create mode 100644 drivers/media/radio/wl128x/fmdrv_v4l2.c
create mode 100644 drivers/media/radio/wl128x/fmdrv_v4l2.h
create mode 100644 drivers/media/video/isp/Makefile
create mode 100644 drivers/media/video/isp/cfa_coef_table.h
create mode 100644 drivers/media/video/isp/gamma_table.h
create mode 100644 drivers/media/video/isp/isp.c
create mode 100644 drivers/media/video/isp/isp.h
create mode 100644 drivers/media/video/isp/ispccdc.c
create mode 100644 drivers/media/video/isp/ispccdc.h
create mode 100644 drivers/media/video/isp/ispccp2.c
create mode 100644 drivers/media/video/isp/ispccp2.h
create mode 100644 drivers/media/video/isp/ispcsi2.c
create mode 100644 drivers/media/video/isp/ispcsi2.h
create mode 100644 drivers/media/video/isp/ispcsiphy.c
create mode 100644 drivers/media/video/isp/ispcsiphy.h
create mode 100644 drivers/media/video/isp/isph3a.h
create mode 100644 drivers/media/video/isp/isph3a_aewb.c
create mode 100644 drivers/media/video/isp/isph3a_af.c
create mode 100644 drivers/media/video/isp/isphist.c
create mode 100644 drivers/media/video/isp/isphist.h
create mode 100644 drivers/media/video/isp/isppreview.c
create mode 100644 drivers/media/video/isp/isppreview.h
create mode 100644 drivers/media/video/isp/ispqueue.c
create mode 100644 drivers/media/video/isp/ispqueue.h
create mode 100644 drivers/media/video/isp/ispreg.h
create mode 100644 drivers/media/video/isp/ispresizer.c
create mode 100644 drivers/media/video/isp/ispresizer.h
create mode 100644 drivers/media/video/isp/ispstat.c
create mode 100644 drivers/media/video/isp/ispstat.h
create mode 100644 drivers/media/video/isp/ispvideo.c
create mode 100644 drivers/media/video/isp/ispvideo.h
create mode 100644 drivers/media/video/isp/luma_enhance_table.h
create mode 100644 drivers/media/video/isp/noise_filter_table.h
create mode 100644 drivers/media/video/v4l2-subdev.c
create mode 100644 drivers/mfd/twl4030-madc.c
create mode 100644 drivers/video/omap2/displays/panel-lgphilips-lb035q02.c
create mode 100644 drivers/video/omap2/displays/panel-samsung-lte430wq-f0c.c
create mode 100644 include/linux/i2c/twl4030-madc.h
create mode 100644 include/linux/media.h
create mode 100644 include/linux/omap3isp.h
create mode 100644 include/linux/v4l2-mediabus.h
create mode 100644 include/linux/v4l2-subdev.h
create mode 100644 include/media/media-device.h
create mode 100644 include/media/media-devnode.h
create mode 100644 include/media/media-entity.h
^ permalink raw reply [flat|nested] 9+ messages in thread* Re: [PULL][linux-yocto] beagleboard: sync with meta-ti linux-omap_2.6.37 2011-06-17 23:18 [PULL][linux-yocto] beagleboard: sync with meta-ti linux-omap_2.6.37 Darren Hart @ 2011-06-18 8:11 ` Koen Kooi 2011-06-18 15:08 ` Darren Hart 0 siblings, 1 reply; 9+ messages in thread From: Koen Kooi @ 2011-06-18 8:11 UTC (permalink / raw) To: Darren Hart; +Cc: yocto, Darren Hart Op 18 jun 2011, om 01:18 heeft Darren Hart het volgende geschreven: > From: Darren Hart <dvhart@linux.intel.com> > > The following commits have been pulled in from the meta-ti linux-omap_2.6.37 > recipe, with the exception of: > USB: ehci: remove structure packing from ehci_def > which hails from mainline and should be applied to yocto/base, while the rest > should be applied to yocto/standard/beagleboard. > > Fixes [YOCTO #764] > Fixes [YOCTO #765] > Fixes [YOCTO #767] > > This brings linux-yocto in sync with the meta-ti linux-omap_2.6.37 recipe and > significantly improves Beagleboard support in linux-yocto. As there are 115 > patches in total, and none of them are new, I have omitted them from the email. You seem to be including the patches that patch the kernel from 37rc7 (or rc8, I forget) to .37 final, which shouldn't apply. So basically leave out the patches in the 'linus' directory. The camera interface also doesn't work, so the 'media' directory can be left out as well. > > The following changes since commit 9cb5c3fb1634e541cacceeb8c8cabe88afa5b080: > > Merge branch 'yocto/standard/base' into yocto/standard/beagleboard (2011-06-06 10:35:20 -0400) > > are available in the git repository at: > > git://git.yoctoproject.org/linux-yocto-2.6.37-contrib dvhart/yocto/standard/beagleboard > http://git.yoctoproject.org/cgit.cgi/linux-yocto-2.6.37-contrib/log/?h=dvhart/yocto/standard/beagleboard > > Alexander Holler (1): > arm: omap3: beagle: Ensure msecure is mux'd to be able to set the RTC > > Antti Koskipaa (1): > v4l: v4l2_subdev userspace crop API > > Arik Nemtsov (1): > wl12xx: Read MAC address from NVS file on HW startup > > Darren Hart (2): > board-omap3beagle: whitespace cleanup > board-omap3beagle: allow for building without wl1271 > > Eliad Peller (1): > wl1271: set wl->vif only if add_interface succeeded. > > Florian Westphal (1): > bridge: stp: ensure mac header is set > > Jesper Juhl (1): > ISDN, Gigaset: Fix memory leak in do_disconnect_req() > > Juuso Oikarinen (1): > wl12xx: Unset bssid filter, ssid and bssid from firmware on disassoc > > Kevin Hilman (1): > OMAP: CPUfreq: ensure policy is fully initialized > > Koen Kooi (10): > omap3: beaglexm: fix DVI reset GPIO > omap3: beaglexm: fix power on of DVI > ARM: OMAP: beagleboard: Add infrastructure to do fixups based on > expansionboard name passed by u-boot > ARM: OMAP: beagleboard: pre-export GPIOs to userspace when using a > Tincantools trainerboard > modedb.c: add proper 720p60 mode > ARM: OMAP: add omap_rev_* macros > omap3: beagleboard: add WIP support for beagleboardtoys WL12xx board > beagleboard: hack in support from xM rev C > omap3: allow 1GHz mpurates > BeagleBoard: Adjust USER button pin for xM > > Laurent Pinchart (35): > v4l: Share code between video_usercopy and video_ioctl2 > v4l: subdev: Don't require core operations > v4l: subdev: Merge v4l2_i2c_new_subdev_cfg and v4l2_i2c_new_subdev > v4l: subdev: Add device node support > v4l: subdev: Uninline the v4l2_subdev_init function > v4l: subdev: Control ioctls support > media: Media device node support > media: Media device > media: Entities, pads and links > media: Entity use count > media: Media device information query > media: Entities, pads and links enumeration > media: Links setup > media: Pipelines and media streams > v4l: Add a media_device pointer to the v4l2_device structure > v4l: Make video_device inherit from media_entity > v4l: Make v4l2_subdev inherit from media_entity > v4l: Move the media/v4l2-mediabus.h header to include/linux > v4l: Replace enums with fixed-sized fields in public structure > v4l: Rename V4L2_MBUS_FMT_GREY8_1X8 to V4L2_MBUS_FMT_Y8_1X8 > v4l: Group media bus pixel codes by types and sort them > alphabetically > v4l: subdev: Add a new file operations class > v4l: v4l2_subdev pad-level operations > v4l: v4l2_subdev userspace format API > v4l: v4l2_subdev userspace frame interval API > v4l: subdev: Generic ioctl support > v4l: Add subdev sensor g_skip_frames operation > v4l: Include linux/videodev2.h in media/v4l2-ctrls.h > v4l: Fix a use-before-set in the control framework > v4l: Add 8-bit YUYV on 16-bit bus and SGRBG10 media bus pixel codes > v4l: Add remaining RAW10 patterns w DPCM pixel code variants > v4l: Add missing 12 bits bayer media bus formats > v4l: Add 12 bits bayer pixel formats > omap3: Add function to register omap3isp platform device structure > OMAP3 ISP driver > > Lennert Buytenhek (1): > ARM: pxa: PXA_ESERIES depends on FB_W100. > > Manjunatha Halli (7): > drivers:media:radio: wl128x: FM Driver common header file > drivers:media:radio: wl128x: FM Driver V4L2 sources > drivers:media:radio: wl128x: FM Driver Common sources > drivers:media:radio: wl128x: FM driver RX sources > drivers:media:radio: wl128x: FM driver TX sources > drivers:media:radio: wl128x: Kconfig & Makefile for wl128x driver > drivers:media:radio: Update Kconfig and Makefile for wl128x FM > driver. > > Nishanth Menon (2): > omap3|4: opp: make omapx_opp_init non-static > OMAP3: beagle xm: enable upto 1GHz OPP > > Pavan Savoy (2): > drivers:misc:ti-st: change protocol parse logic > Bluetooth: btwilink driver > > Peter 'p2' De Schrijver (1): > OMAP: CPUfreq: ensure driver initializes after cpufreq framework and > governors > > Rabin Vincent (1): > USB: ehci: remove structure packing from ehci_def > > Rajendra Nayak (1): > OMAP3 PM: CPUFreq driver for OMAP3 > > Robert Nelson (2): > omap: Beagle: detect new xM revision B > xM audio fix from Ashok > > Sakari Ailus (2): > v4l: subdev: Events support > media: Entity graph traversal > > Sanjeev Premi (1): > omap3: Add basic support for 720MHz part > > Sergio Aguirre (2): > omap3: Remove unusued ISP CBUFF resource > omap2: Fix camera resources for multiomap > > Shahar Levi (3): > wl1271: 11n Support, Add Definitions > wl1271: 11n Support, ACX Commands > wl1271: 11n Support, functionality and configuration ability > > Silesh C V (1): > OMAP: PM: CPUFREQ: Fix conditional compilation > > Stanimir Varbanov (1): > v4l: Create v4l2 subdev file handle structure > > Steve Sakoman (18): > mmc: don't display single block read console messages > MTD: silence ecc errors on mtdblock0 > OMAP: DSS2: enable hsclk in dsi_pll_init for OMAP36XX > drivers: net: smsc911x: return ENODEV if device is not found > drivers: input: touchscreen: ads7846: return ENODEV if device is not > found > ASoC: enable audio capture by default for twl4030 > MFD: enable madc clock > MFD: add twl4030 madc driver > ARM: OMAP: Add twl4030 madc support to Overo > ARM: OMAP: Add twl4030 madc support to Beagle > OMAP: DSS2: Add support for Samsung LTE430WQ-F0C panel > OMAP: DSS2: Add support for LG Philips LB035Q02 panel > OMAP: DSS2: add bootarg for selecting svideo or composite for tv > output > ARM: OMAP2: mmc-twl4030: move clock input selection prior to vcc test > RTC: add support for backup battery recharge > ARM: OMAP: automatically set musb mode in platform data based on > CONFIG options > OMAP: DSS2: check for both cpu type and revision, rather than just > revision > OMAP: DSS2: Add DSS2 support for Overo > > Thara Gopinath (13): > OMAP3: PM: Adding T2 enabling of smartreflex > OMAP: Introduce a user list for each voltage domain instance in the > voltage driver. > OMAP: Introduce API in the OPP layer to find the opp entry > corresponding to a voltage. > OMAP: Introduce API to register a device with a voltagedomain > OMAP: Introduce device specific set rate and get rate in omap_device > structure > OMAP: Voltage layer changes to support DVFS. > OMAP: Introduce dependent voltage domain support. > OMAP: Introduce device scale > OMAP: Disable smartreflex across DVFS > OMAP3: Introduce custom set rate and get rate APIs for scalable > devices > OMAP3: Update cpufreq driver to use the new set_rate API > OMAP3: Introduce voltage domain info in the hwmod structures. > OMAP3: Add voltage dependency table for VDD1. > > Thomas Weber (1): > OMAP: Enable Magic SysRq on serial console ttyOx > > Tuukka Toivonen (1): > ARM: OMAP3: Update Camera ISP definitions for OMAP3630 > > Documentation/ABI/testing/sysfs-bus-media | 6 + > Documentation/DocBook/Makefile | 5 +- > Documentation/DocBook/media-entities.tmpl | 50 + > Documentation/DocBook/media.tmpl | 3 + > Documentation/DocBook/v4l/dev-subdev.xml | 307 +++ > Documentation/DocBook/v4l/media-controller.xml | 89 + > Documentation/DocBook/v4l/media-func-close.xml | 59 + > Documentation/DocBook/v4l/media-func-ioctl.xml | 116 + > Documentation/DocBook/v4l/media-func-open.xml | 94 + > .../DocBook/v4l/media-ioc-device-info.xml | 133 ++ > .../DocBook/v4l/media-ioc-enum-entities.xml | 308 +++ > Documentation/DocBook/v4l/media-ioc-enum-links.xml | 207 ++ > Documentation/DocBook/v4l/media-ioc-setup-link.xml | 93 + > Documentation/DocBook/v4l/subdev-formats.xml | 2467 ++++++++++++++++++++ > Documentation/DocBook/v4l/v4l2.xml | 7 + > Documentation/DocBook/v4l/vidioc-streamon.xml | 9 + > .../v4l/vidioc-subdev-enum-frame-interval.xml | 146 ++ > .../DocBook/v4l/vidioc-subdev-enum-frame-size.xml | 148 ++ > .../DocBook/v4l/vidioc-subdev-enum-mbus-code.xml | 113 + > Documentation/DocBook/v4l/vidioc-subdev-g-crop.xml | 149 ++ > Documentation/DocBook/v4l/vidioc-subdev-g-fmt.xml | 174 ++ > .../DocBook/v4l/vidioc-subdev-g-frame-interval.xml | 135 ++ > Documentation/media-framework.txt | 353 +++ > Documentation/video4linux/v4l2-framework.txt | 129 +- > arch/arm/mach-omap2/board-omap3beagle.c | 409 ++++- > arch/arm/mach-omap2/board-overo.c | 247 ++- > arch/arm/mach-omap2/clock.h | 14 +- > arch/arm/mach-omap2/clock34xx.c | 2 + > arch/arm/mach-omap2/control.h | 7 + > arch/arm/mach-omap2/devices.c | 64 +- > arch/arm/mach-omap2/devices.h | 17 + > arch/arm/mach-omap2/hsmmc.c | 14 +- > arch/arm/mach-omap2/id.c | 10 + > arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 3 + > arch/arm/mach-omap2/omap_twl.c | 16 + > arch/arm/mach-omap2/opp3xxx_data.c | 66 +- > arch/arm/mach-omap2/opp4xxx_data.c | 3 +- > arch/arm/mach-omap2/pm.c | 110 + > arch/arm/mach-omap2/voltage.c | 369 +++- > arch/arm/mach-pxa/Kconfig | 1 + > arch/arm/plat-omap/clock.c | 2 +- > arch/arm/plat-omap/cpu-omap.c | 38 +- > arch/arm/plat-omap/include/plat/cpu.h | 57 + > arch/arm/plat-omap/include/plat/omap34xx.h | 16 +- > arch/arm/plat-omap/include/plat/omap_device.h | 12 +- > arch/arm/plat-omap/include/plat/voltage.h | 20 + > arch/arm/plat-omap/omap_device.c | 139 ++ > block/blk-core.c | 7 +- > drivers/base/power/opp.c | 28 + > drivers/bluetooth/Kconfig | 10 + > drivers/bluetooth/Makefile | 1 + > drivers/bluetooth/btwilink.c | 397 ++++ > drivers/input/touchscreen/ads7846.c | 13 +- > drivers/isdn/gigaset/capi.c | 1 + > drivers/media/Kconfig | 22 + > drivers/media/Makefile | 10 +- > drivers/media/media-device.c | 382 +++ > drivers/media/media-devnode.c | 321 +++ > drivers/media/media-entity.c | 536 +++++ > drivers/media/radio/Kconfig | 3 + > drivers/media/radio/Makefile | 1 + > drivers/media/radio/radio-si4713.c | 2 +- > drivers/media/radio/wl128x/Kconfig | 17 + > drivers/media/radio/wl128x/Makefile | 6 + > drivers/media/radio/wl128x/fmdrv.h | 244 ++ > drivers/media/radio/wl128x/fmdrv_common.c | 1677 +++++++++++++ > drivers/media/radio/wl128x/fmdrv_common.h | 402 ++++ > drivers/media/radio/wl128x/fmdrv_rx.c | 847 +++++++ > drivers/media/radio/wl128x/fmdrv_rx.h | 59 + > drivers/media/radio/wl128x/fmdrv_tx.c | 425 ++++ > drivers/media/radio/wl128x/fmdrv_tx.h | 37 + > drivers/media/radio/wl128x/fmdrv_v4l2.c | 580 +++++ > drivers/media/radio/wl128x/fmdrv_v4l2.h | 33 + > drivers/media/video/Kconfig | 13 + > drivers/media/video/Makefile | 4 +- > drivers/media/video/cafe_ccic.c | 11 +- > drivers/media/video/davinci/vpfe_capture.c | 2 +- > drivers/media/video/davinci/vpif_capture.c | 2 +- > drivers/media/video/davinci/vpif_display.c | 2 +- > drivers/media/video/isp/Makefile | 13 + > drivers/media/video/isp/cfa_coef_table.h | 601 +++++ > drivers/media/video/isp/gamma_table.h | 90 + > drivers/media/video/isp/isp.c | 2221 ++++++++++++++++++ > drivers/media/video/isp/isp.h | 427 ++++ > drivers/media/video/isp/ispccdc.c | 2280 ++++++++++++++++++ > drivers/media/video/isp/ispccdc.h | 223 ++ > drivers/media/video/isp/ispccp2.c | 1189 ++++++++++ > drivers/media/video/isp/ispccp2.h | 101 + > drivers/media/video/isp/ispcsi2.c | 1332 +++++++++++ > drivers/media/video/isp/ispcsi2.h | 169 ++ > drivers/media/video/isp/ispcsiphy.c | 247 ++ > drivers/media/video/isp/ispcsiphy.h | 74 + > drivers/media/video/isp/isph3a.h | 117 + > drivers/media/video/isp/isph3a_aewb.c | 374 +++ > drivers/media/video/isp/isph3a_af.c | 429 ++++ > drivers/media/video/isp/isphist.c | 520 ++++ > drivers/media/video/isp/isphist.h | 40 + > drivers/media/video/isp/isppreview.c | 2120 +++++++++++++++++ > drivers/media/video/isp/isppreview.h | 214 ++ > drivers/media/video/isp/ispqueue.c | 1136 +++++++++ > drivers/media/video/isp/ispqueue.h | 185 ++ > drivers/media/video/isp/ispreg.h | 1589 +++++++++++++ > drivers/media/video/isp/ispresizer.c | 1710 ++++++++++++++ > drivers/media/video/isp/ispresizer.h | 150 ++ > drivers/media/video/isp/ispstat.c | 1100 +++++++++ > drivers/media/video/isp/ispstat.h | 169 ++ > drivers/media/video/isp/ispvideo.c | 1264 ++++++++++ > drivers/media/video/isp/ispvideo.h | 202 ++ > drivers/media/video/isp/luma_enhance_table.h | 154 ++ > drivers/media/video/isp/noise_filter_table.h | 90 + > drivers/media/video/ivtv/ivtv-i2c.c | 11 +- > drivers/media/video/mt9m001.c | 2 +- > drivers/media/video/mt9v022.c | 4 +- > drivers/media/video/ov6650.c | 10 +- > drivers/media/video/s5p-fimc/fimc-capture.c | 2 +- > drivers/media/video/sh_mobile_csi2.c | 6 +- > drivers/media/video/sh_vou.c | 2 +- > drivers/media/video/soc_camera.c | 2 +- > drivers/media/video/soc_mediabus.c | 2 +- > drivers/media/video/v4l2-common.c | 22 +- > drivers/media/video/v4l2-ctrls.c | 2 +- > drivers/media/video/v4l2-dev.c | 76 +- > drivers/media/video/v4l2-device.c | 66 +- > drivers/media/video/v4l2-ioctl.c | 216 +-- > drivers/media/video/v4l2-subdev.c | 346 +++ > drivers/mfd/Kconfig | 21 + > drivers/mfd/Makefile | 1 + > drivers/mfd/twl-core.c | 8 + > drivers/mfd/twl4030-madc.c | 537 +++++ > drivers/misc/ti-st/st_core.c | 355 +-- > drivers/misc/ti-st/st_kim.c | 56 +- > drivers/mmc/card/block.c | 4 +- > drivers/mtd/nand/nand_ecc.c | 2 +- > drivers/net/smsc911x.c | 4 +- > drivers/net/wireless/wl12xx/Kconfig | 10 + > drivers/net/wireless/wl12xx/wl1271.h | 11 +- > drivers/net/wireless/wl12xx/wl1271_acx.c | 83 + > drivers/net/wireless/wl12xx/wl1271_acx.h | 86 + > drivers/net/wireless/wl12xx/wl1271_main.c | 161 +- > drivers/net/wireless/wl12xx/wl1271_rx.c | 6 + > drivers/net/wireless/wl12xx/wl1271_tx.c | 11 + > drivers/rtc/rtc-twl.c | 25 + > drivers/serial/omap-serial.c | 4 + > drivers/video/modedb.c | 4 + > drivers/video/omap2/displays/Kconfig | 12 + > drivers/video/omap2/displays/Makefile | 2 + > .../omap2/displays/panel-lgphilips-lb035q02.c | 244 ++ > .../omap2/displays/panel-samsung-lte430wq-f0c.c | 154 ++ > drivers/video/omap2/dss/dispc.c | 4 +- > drivers/video/omap2/dss/dpi.c | 7 +- > drivers/video/omap2/dss/venc.c | 22 + > drivers/video/omap2/omapfb/omapfb-main.c | 10 +- > fs/buffer.c | 3 +- > include/linux/Kbuild | 4 + > include/linux/i2c/twl.h | 1 + > include/linux/i2c/twl4030-madc.h | 130 + > include/linux/media.h | 132 ++ > include/linux/omap3isp.h | 631 +++++ > include/linux/opp.h | 8 + > include/linux/ti_wilink_st.h | 40 +- > include/linux/usb/ehci_def.h | 6 +- > include/linux/v4l2-mediabus.h | 108 + > include/linux/v4l2-subdev.h | 141 ++ > include/linux/videodev2.h | 4 + > include/media/media-device.h | 95 + > include/media/media-devnode.h | 97 + > include/media/media-entity.h | 147 ++ > include/media/soc_mediabus.h | 3 +- > include/media/v4l2-common.h | 18 +- > include/media/v4l2-ctrls.h | 1 + > include/media/v4l2-dev.h | 25 +- > include/media/v4l2-device.h | 4 + > include/media/v4l2-ioctl.h | 3 + > include/media/v4l2-mediabus.h | 61 +- > include/media/v4l2-subdev.h | 120 +- > net/bridge/br_stp_bpdu.c | 2 + > sound/soc/codecs/twl4030.c | 4 +- > sound/soc/omap/omap-mcbsp.c | 3 + > 178 files changed, 37220 insertions(+), 745 deletions(-) > create mode 100644 Documentation/ABI/testing/sysfs-bus-media > create mode 100644 Documentation/DocBook/v4l/dev-subdev.xml > create mode 100644 Documentation/DocBook/v4l/media-controller.xml > create mode 100644 Documentation/DocBook/v4l/media-func-close.xml > create mode 100644 Documentation/DocBook/v4l/media-func-ioctl.xml > create mode 100644 Documentation/DocBook/v4l/media-func-open.xml > create mode 100644 Documentation/DocBook/v4l/media-ioc-device-info.xml > create mode 100644 Documentation/DocBook/v4l/media-ioc-enum-entities.xml > create mode 100644 Documentation/DocBook/v4l/media-ioc-enum-links.xml > create mode 100644 Documentation/DocBook/v4l/media-ioc-setup-link.xml > create mode 100644 Documentation/DocBook/v4l/subdev-formats.xml > create mode 100644 Documentation/DocBook/v4l/vidioc-subdev-enum-frame-interval.xml > create mode 100644 Documentation/DocBook/v4l/vidioc-subdev-enum-frame-size.xml > create mode 100644 Documentation/DocBook/v4l/vidioc-subdev-enum-mbus-code.xml > create mode 100644 Documentation/DocBook/v4l/vidioc-subdev-g-crop.xml > create mode 100644 Documentation/DocBook/v4l/vidioc-subdev-g-fmt.xml > create mode 100644 Documentation/DocBook/v4l/vidioc-subdev-g-frame-interval.xml > create mode 100644 Documentation/media-framework.txt > create mode 100644 arch/arm/mach-omap2/devices.h > create mode 100644 drivers/bluetooth/btwilink.c > create mode 100644 drivers/media/media-device.c > create mode 100644 drivers/media/media-devnode.c > create mode 100644 drivers/media/media-entity.c > create mode 100644 drivers/media/radio/wl128x/Kconfig > create mode 100644 drivers/media/radio/wl128x/Makefile > create mode 100644 drivers/media/radio/wl128x/fmdrv.h > create mode 100644 drivers/media/radio/wl128x/fmdrv_common.c > create mode 100644 drivers/media/radio/wl128x/fmdrv_common.h > create mode 100644 drivers/media/radio/wl128x/fmdrv_rx.c > create mode 100644 drivers/media/radio/wl128x/fmdrv_rx.h > create mode 100644 drivers/media/radio/wl128x/fmdrv_tx.c > create mode 100644 drivers/media/radio/wl128x/fmdrv_tx.h > create mode 100644 drivers/media/radio/wl128x/fmdrv_v4l2.c > create mode 100644 drivers/media/radio/wl128x/fmdrv_v4l2.h > create mode 100644 drivers/media/video/isp/Makefile > create mode 100644 drivers/media/video/isp/cfa_coef_table.h > create mode 100644 drivers/media/video/isp/gamma_table.h > create mode 100644 drivers/media/video/isp/isp.c > create mode 100644 drivers/media/video/isp/isp.h > create mode 100644 drivers/media/video/isp/ispccdc.c > create mode 100644 drivers/media/video/isp/ispccdc.h > create mode 100644 drivers/media/video/isp/ispccp2.c > create mode 100644 drivers/media/video/isp/ispccp2.h > create mode 100644 drivers/media/video/isp/ispcsi2.c > create mode 100644 drivers/media/video/isp/ispcsi2.h > create mode 100644 drivers/media/video/isp/ispcsiphy.c > create mode 100644 drivers/media/video/isp/ispcsiphy.h > create mode 100644 drivers/media/video/isp/isph3a.h > create mode 100644 drivers/media/video/isp/isph3a_aewb.c > create mode 100644 drivers/media/video/isp/isph3a_af.c > create mode 100644 drivers/media/video/isp/isphist.c > create mode 100644 drivers/media/video/isp/isphist.h > create mode 100644 drivers/media/video/isp/isppreview.c > create mode 100644 drivers/media/video/isp/isppreview.h > create mode 100644 drivers/media/video/isp/ispqueue.c > create mode 100644 drivers/media/video/isp/ispqueue.h > create mode 100644 drivers/media/video/isp/ispreg.h > create mode 100644 drivers/media/video/isp/ispresizer.c > create mode 100644 drivers/media/video/isp/ispresizer.h > create mode 100644 drivers/media/video/isp/ispstat.c > create mode 100644 drivers/media/video/isp/ispstat.h > create mode 100644 drivers/media/video/isp/ispvideo.c > create mode 100644 drivers/media/video/isp/ispvideo.h > create mode 100644 drivers/media/video/isp/luma_enhance_table.h > create mode 100644 drivers/media/video/isp/noise_filter_table.h > create mode 100644 drivers/media/video/v4l2-subdev.c > create mode 100644 drivers/mfd/twl4030-madc.c > create mode 100644 drivers/video/omap2/displays/panel-lgphilips-lb035q02.c > create mode 100644 drivers/video/omap2/displays/panel-samsung-lte430wq-f0c.c > create mode 100644 include/linux/i2c/twl4030-madc.h > create mode 100644 include/linux/media.h > create mode 100644 include/linux/omap3isp.h > create mode 100644 include/linux/v4l2-mediabus.h > create mode 100644 include/linux/v4l2-subdev.h > create mode 100644 include/media/media-device.h > create mode 100644 include/media/media-devnode.h > create mode 100644 include/media/media-entity.h > > _______________________________________________ > yocto mailing list > yocto@yoctoproject.org > https://lists.yoctoproject.org/listinfo/yocto ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PULL][linux-yocto] beagleboard: sync with meta-ti linux-omap_2.6.37 2011-06-18 8:11 ` Koen Kooi @ 2011-06-18 15:08 ` Darren Hart 2011-06-18 15:10 ` Koen Kooi 0 siblings, 1 reply; 9+ messages in thread From: Darren Hart @ 2011-06-18 15:08 UTC (permalink / raw) To: Koen Kooi; +Cc: Darren Hart, yocto On 06/18/2011 01:11 AM, Koen Kooi wrote: > > Op 18 jun 2011, om 01:18 heeft Darren Hart het volgende geschreven: > >> From: Darren Hart <dvhart@linux.intel.com> >> >> The following commits have been pulled in from the meta-ti >> linux-omap_2.6.37 recipe, with the exception of: USB: ehci: remove >> structure packing from ehci_def which hails from mainline and >> should be applied to yocto/base, while the rest should be applied >> to yocto/standard/beagleboard. >> >> Fixes [YOCTO #764] Fixes [YOCTO #765] Fixes [YOCTO #767] >> >> This brings linux-yocto in sync with the meta-ti linux-omap_2.6.37 >> recipe and significantly improves Beagleboard support in >> linux-yocto. As there are 115 patches in total, and none of them >> are new, I have omitted them from the email. > > > You seem to be including the patches that patch the kernel from > 37rc7 (or rc8, I forget) to .37 final, which shouldn't apply. So > basically leave out the patches in the 'linus' directory. There were about 200 patches in total, I've removed all those that reverse applied and failed do to a conflict that was obviously a merge of a very similar patch. That accounted for most of the 37-rc[78] to 37 patches from the linus directory. > The camera > interface also doesn't work, so the 'media' directory can be left out > as well. The goal was to stay as close to the meta-ti/linux-omap_2.6.37 recipe as possible with the linux-yocto kernel repository. Will you be removing all of the media directory from there as well? I don't want to remove them from here if you'll be *adding* to them there. However, if you'll be sure to just be replacing them there, then I can drop them here. -- Darren > >> >> The following changes since commit >> 9cb5c3fb1634e541cacceeb8c8cabe88afa5b080: >> >> Merge branch 'yocto/standard/base' into yocto/standard/beagleboard >> (2011-06-06 10:35:20 -0400) >> >> are available in the git repository at: >> >> git://git.yoctoproject.org/linux-yocto-2.6.37-contrib >> dvhart/yocto/standard/beagleboard >> http://git.yoctoproject.org/cgit.cgi/linux-yocto-2.6.37-contrib/log/?h=dvhart/yocto/standard/beagleboard >> >> >> Alexander Holler (1): >> arm: omap3: beagle: Ensure msecure is mux'd to be able to set the >> RTC >> >> Antti Koskipaa (1): v4l: v4l2_subdev userspace crop API >> >> Arik Nemtsov (1): wl12xx: Read MAC address from NVS file on HW >> startup >> >> Darren Hart (2): board-omap3beagle: whitespace cleanup >> board-omap3beagle: allow for building without wl1271 >> >> Eliad Peller (1): wl1271: set wl->vif only if add_interface >> succeeded. >> >> Florian Westphal (1): bridge: stp: ensure mac header is set >> >> Jesper Juhl (1): ISDN, Gigaset: Fix memory leak in >> do_disconnect_req() >> >> Juuso Oikarinen (1): wl12xx: Unset bssid filter, ssid and bssid >> from firmware on disassoc >> >> Kevin Hilman (1): OMAP: CPUfreq: ensure policy is fully >> initialized >> >> Koen Kooi (10): omap3: beaglexm: fix DVI reset GPIO omap3: >> beaglexm: fix power on of DVI ARM: OMAP: beagleboard: Add >> infrastructure to do fixups based on expansionboard name passed by >> u-boot ARM: OMAP: beagleboard: pre-export GPIOs to userspace when >> using a Tincantools trainerboard modedb.c: add proper 720p60 mode >> ARM: OMAP: add omap_rev_* macros omap3: beagleboard: add WIP >> support for beagleboardtoys WL12xx board beagleboard: hack in >> support from xM rev C omap3: allow 1GHz mpurates BeagleBoard: >> Adjust USER button pin for xM >> >> Laurent Pinchart (35): v4l: Share code between video_usercopy and >> video_ioctl2 v4l: subdev: Don't require core operations v4l: >> subdev: Merge v4l2_i2c_new_subdev_cfg and v4l2_i2c_new_subdev v4l: >> subdev: Add device node support v4l: subdev: Uninline the >> v4l2_subdev_init function v4l: subdev: Control ioctls support >> media: Media device node support media: Media device media: >> Entities, pads and links media: Entity use count media: Media >> device information query media: Entities, pads and links >> enumeration media: Links setup media: Pipelines and media streams >> v4l: Add a media_device pointer to the v4l2_device structure v4l: >> Make video_device inherit from media_entity v4l: Make v4l2_subdev >> inherit from media_entity v4l: Move the media/v4l2-mediabus.h >> header to include/linux v4l: Replace enums with fixed-sized fields >> in public structure v4l: Rename V4L2_MBUS_FMT_GREY8_1X8 to >> V4L2_MBUS_FMT_Y8_1X8 v4l: Group media bus pixel codes by types and >> sort them alphabetically v4l: subdev: Add a new file operations >> class v4l: v4l2_subdev pad-level operations v4l: v4l2_subdev >> userspace format API v4l: v4l2_subdev userspace frame interval API >> v4l: subdev: Generic ioctl support v4l: Add subdev sensor >> g_skip_frames operation v4l: Include linux/videodev2.h in >> media/v4l2-ctrls.h v4l: Fix a use-before-set in the control >> framework v4l: Add 8-bit YUYV on 16-bit bus and SGRBG10 media bus >> pixel codes v4l: Add remaining RAW10 patterns w DPCM pixel code >> variants v4l: Add missing 12 bits bayer media bus formats v4l: Add >> 12 bits bayer pixel formats omap3: Add function to register >> omap3isp platform device structure OMAP3 ISP driver >> >> Lennert Buytenhek (1): ARM: pxa: PXA_ESERIES depends on FB_W100. >> >> Manjunatha Halli (7): drivers:media:radio: wl128x: FM Driver common >> header file drivers:media:radio: wl128x: FM Driver V4L2 sources >> drivers:media:radio: wl128x: FM Driver Common sources >> drivers:media:radio: wl128x: FM driver RX sources >> drivers:media:radio: wl128x: FM driver TX sources >> drivers:media:radio: wl128x: Kconfig & Makefile for wl128x driver >> drivers:media:radio: Update Kconfig and Makefile for wl128x FM >> driver. >> >> Nishanth Menon (2): omap3|4: opp: make omapx_opp_init non-static >> OMAP3: beagle xm: enable upto 1GHz OPP >> >> Pavan Savoy (2): drivers:misc:ti-st: change protocol parse logic >> Bluetooth: btwilink driver >> >> Peter 'p2' De Schrijver (1): OMAP: CPUfreq: ensure driver >> initializes after cpufreq framework and governors >> >> Rabin Vincent (1): USB: ehci: remove structure packing from >> ehci_def >> >> Rajendra Nayak (1): OMAP3 PM: CPUFreq driver for OMAP3 >> >> Robert Nelson (2): omap: Beagle: detect new xM revision B xM audio >> fix from Ashok >> >> Sakari Ailus (2): v4l: subdev: Events support media: Entity graph >> traversal >> >> Sanjeev Premi (1): omap3: Add basic support for 720MHz part >> >> Sergio Aguirre (2): omap3: Remove unusued ISP CBUFF resource omap2: >> Fix camera resources for multiomap >> >> Shahar Levi (3): wl1271: 11n Support, Add Definitions wl1271: 11n >> Support, ACX Commands wl1271: 11n Support, functionality and >> configuration ability >> >> Silesh C V (1): OMAP: PM: CPUFREQ: Fix conditional compilation >> >> Stanimir Varbanov (1): v4l: Create v4l2 subdev file handle >> structure >> >> Steve Sakoman (18): mmc: don't display single block read console >> messages MTD: silence ecc errors on mtdblock0 OMAP: DSS2: enable >> hsclk in dsi_pll_init for OMAP36XX drivers: net: smsc911x: return >> ENODEV if device is not found drivers: input: touchscreen: ads7846: >> return ENODEV if device is not found ASoC: enable audio capture by >> default for twl4030 MFD: enable madc clock MFD: add twl4030 madc >> driver ARM: OMAP: Add twl4030 madc support to Overo ARM: OMAP: Add >> twl4030 madc support to Beagle OMAP: DSS2: Add support for Samsung >> LTE430WQ-F0C panel OMAP: DSS2: Add support for LG Philips LB035Q02 >> panel OMAP: DSS2: add bootarg for selecting svideo or composite for >> tv output ARM: OMAP2: mmc-twl4030: move clock input selection prior >> to vcc test RTC: add support for backup battery recharge ARM: OMAP: >> automatically set musb mode in platform data based on CONFIG >> options OMAP: DSS2: check for both cpu type and revision, rather >> than just revision OMAP: DSS2: Add DSS2 support for Overo >> >> Thara Gopinath (13): OMAP3: PM: Adding T2 enabling of smartreflex >> OMAP: Introduce a user list for each voltage domain instance in >> the voltage driver. OMAP: Introduce API in the OPP layer to find >> the opp entry corresponding to a voltage. OMAP: Introduce API to >> register a device with a voltagedomain OMAP: Introduce device >> specific set rate and get rate in omap_device structure OMAP: >> Voltage layer changes to support DVFS. OMAP: Introduce dependent >> voltage domain support. OMAP: Introduce device scale OMAP: Disable >> smartreflex across DVFS OMAP3: Introduce custom set rate and get >> rate APIs for scalable devices OMAP3: Update cpufreq driver to use >> the new set_rate API OMAP3: Introduce voltage domain info in the >> hwmod structures. OMAP3: Add voltage dependency table for VDD1. >> >> Thomas Weber (1): OMAP: Enable Magic SysRq on serial console ttyOx >> >> Tuukka Toivonen (1): ARM: OMAP3: Update Camera ISP definitions for >> OMAP3630 >> >> Documentation/ABI/testing/sysfs-bus-media | 6 + >> Documentation/DocBook/Makefile | 5 +- >> Documentation/DocBook/media-entities.tmpl | 50 + >> Documentation/DocBook/media.tmpl | 3 + >> Documentation/DocBook/v4l/dev-subdev.xml | 307 +++ >> Documentation/DocBook/v4l/media-controller.xml | 89 + >> Documentation/DocBook/v4l/media-func-close.xml | 59 + >> Documentation/DocBook/v4l/media-func-ioctl.xml | 116 + >> Documentation/DocBook/v4l/media-func-open.xml | 94 + >> .../DocBook/v4l/media-ioc-device-info.xml | 133 ++ >> .../DocBook/v4l/media-ioc-enum-entities.xml | 308 +++ >> Documentation/DocBook/v4l/media-ioc-enum-links.xml | 207 ++ >> Documentation/DocBook/v4l/media-ioc-setup-link.xml | 93 + >> Documentation/DocBook/v4l/subdev-formats.xml | 2467 >> ++++++++++++++++++++ Documentation/DocBook/v4l/v4l2.xml >> | 7 + Documentation/DocBook/v4l/vidioc-streamon.xml | 9 >> + .../v4l/vidioc-subdev-enum-frame-interval.xml | 146 ++ >> .../DocBook/v4l/vidioc-subdev-enum-frame-size.xml | 148 ++ >> .../DocBook/v4l/vidioc-subdev-enum-mbus-code.xml | 113 + >> Documentation/DocBook/v4l/vidioc-subdev-g-crop.xml | 149 ++ >> Documentation/DocBook/v4l/vidioc-subdev-g-fmt.xml | 174 ++ >> .../DocBook/v4l/vidioc-subdev-g-frame-interval.xml | 135 ++ >> Documentation/media-framework.txt | 353 +++ >> Documentation/video4linux/v4l2-framework.txt | 129 +- >> arch/arm/mach-omap2/board-omap3beagle.c | 409 ++++- >> arch/arm/mach-omap2/board-overo.c | 247 ++- >> arch/arm/mach-omap2/clock.h | 14 +- >> arch/arm/mach-omap2/clock34xx.c | 2 + >> arch/arm/mach-omap2/control.h | 7 + >> arch/arm/mach-omap2/devices.c | 64 +- >> arch/arm/mach-omap2/devices.h | 17 + >> arch/arm/mach-omap2/hsmmc.c | 14 +- >> arch/arm/mach-omap2/id.c | 10 + >> arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 3 + >> arch/arm/mach-omap2/omap_twl.c | 16 + >> arch/arm/mach-omap2/opp3xxx_data.c | 66 +- >> arch/arm/mach-omap2/opp4xxx_data.c | 3 +- >> arch/arm/mach-omap2/pm.c | 110 + >> arch/arm/mach-omap2/voltage.c | 369 +++- >> arch/arm/mach-pxa/Kconfig | 1 + >> arch/arm/plat-omap/clock.c | 2 +- >> arch/arm/plat-omap/cpu-omap.c | 38 +- >> arch/arm/plat-omap/include/plat/cpu.h | 57 + >> arch/arm/plat-omap/include/plat/omap34xx.h | 16 +- >> arch/arm/plat-omap/include/plat/omap_device.h | 12 +- >> arch/arm/plat-omap/include/plat/voltage.h | 20 + >> arch/arm/plat-omap/omap_device.c | 139 ++ >> block/blk-core.c | 7 +- >> drivers/base/power/opp.c | 28 + >> drivers/bluetooth/Kconfig | 10 + >> drivers/bluetooth/Makefile | 1 + >> drivers/bluetooth/btwilink.c | 397 ++++ >> drivers/input/touchscreen/ads7846.c | 13 +- >> drivers/isdn/gigaset/capi.c | 1 + >> drivers/media/Kconfig | 22 + >> drivers/media/Makefile | 10 +- >> drivers/media/media-device.c | 382 +++ >> drivers/media/media-devnode.c | 321 +++ >> drivers/media/media-entity.c | 536 +++++ >> drivers/media/radio/Kconfig | 3 + >> drivers/media/radio/Makefile | 1 + >> drivers/media/radio/radio-si4713.c | 2 +- >> drivers/media/radio/wl128x/Kconfig | 17 + >> drivers/media/radio/wl128x/Makefile | 6 + >> drivers/media/radio/wl128x/fmdrv.h | 244 ++ >> drivers/media/radio/wl128x/fmdrv_common.c | 1677 >> +++++++++++++ drivers/media/radio/wl128x/fmdrv_common.h | >> 402 ++++ drivers/media/radio/wl128x/fmdrv_rx.c | 847 >> +++++++ drivers/media/radio/wl128x/fmdrv_rx.h | 59 >> + drivers/media/radio/wl128x/fmdrv_tx.c | 425 ++++ >> drivers/media/radio/wl128x/fmdrv_tx.h | 37 + >> drivers/media/radio/wl128x/fmdrv_v4l2.c | 580 +++++ >> drivers/media/radio/wl128x/fmdrv_v4l2.h | 33 + >> drivers/media/video/Kconfig | 13 + >> drivers/media/video/Makefile | 4 +- >> drivers/media/video/cafe_ccic.c | 11 +- >> drivers/media/video/davinci/vpfe_capture.c | 2 +- >> drivers/media/video/davinci/vpif_capture.c | 2 +- >> drivers/media/video/davinci/vpif_display.c | 2 +- >> drivers/media/video/isp/Makefile | 13 + >> drivers/media/video/isp/cfa_coef_table.h | 601 +++++ >> drivers/media/video/isp/gamma_table.h | 90 + >> drivers/media/video/isp/isp.c | 2221 >> ++++++++++++++++++ drivers/media/video/isp/isp.h >> | 427 ++++ drivers/media/video/isp/ispccdc.c | >> 2280 ++++++++++++++++++ drivers/media/video/isp/ispccdc.h >> | 223 ++ drivers/media/video/isp/ispccp2.c | 1189 >> ++++++++++ drivers/media/video/isp/ispccp2.h | >> 101 + drivers/media/video/isp/ispcsi2.c | 1332 >> +++++++++++ drivers/media/video/isp/ispcsi2.h | >> 169 ++ drivers/media/video/isp/ispcsiphy.c | 247 >> ++ drivers/media/video/isp/ispcsiphy.h | 74 + >> drivers/media/video/isp/isph3a.h | 117 + >> drivers/media/video/isp/isph3a_aewb.c | 374 +++ >> drivers/media/video/isp/isph3a_af.c | 429 ++++ >> drivers/media/video/isp/isphist.c | 520 ++++ >> drivers/media/video/isp/isphist.h | 40 + >> drivers/media/video/isp/isppreview.c | 2120 >> +++++++++++++++++ drivers/media/video/isp/isppreview.h >> | 214 ++ drivers/media/video/isp/ispqueue.c | 1136 >> +++++++++ drivers/media/video/isp/ispqueue.h | 185 >> ++ drivers/media/video/isp/ispreg.h | 1589 >> +++++++++++++ drivers/media/video/isp/ispresizer.c | >> 1710 ++++++++++++++ drivers/media/video/isp/ispresizer.h >> | 150 ++ drivers/media/video/isp/ispstat.c | 1100 >> +++++++++ drivers/media/video/isp/ispstat.h | 169 >> ++ drivers/media/video/isp/ispvideo.c | 1264 >> ++++++++++ drivers/media/video/isp/ispvideo.h | >> 202 ++ drivers/media/video/isp/luma_enhance_table.h | 154 >> ++ drivers/media/video/isp/noise_filter_table.h | 90 + >> drivers/media/video/ivtv/ivtv-i2c.c | 11 +- >> drivers/media/video/mt9m001.c | 2 +- >> drivers/media/video/mt9v022.c | 4 +- >> drivers/media/video/ov6650.c | 10 +- >> drivers/media/video/s5p-fimc/fimc-capture.c | 2 +- >> drivers/media/video/sh_mobile_csi2.c | 6 +- >> drivers/media/video/sh_vou.c | 2 +- >> drivers/media/video/soc_camera.c | 2 +- >> drivers/media/video/soc_mediabus.c | 2 +- >> drivers/media/video/v4l2-common.c | 22 +- >> drivers/media/video/v4l2-ctrls.c | 2 +- >> drivers/media/video/v4l2-dev.c | 76 +- >> drivers/media/video/v4l2-device.c | 66 +- >> drivers/media/video/v4l2-ioctl.c | 216 +-- >> drivers/media/video/v4l2-subdev.c | 346 +++ >> drivers/mfd/Kconfig | 21 + >> drivers/mfd/Makefile | 1 + >> drivers/mfd/twl-core.c | 8 + >> drivers/mfd/twl4030-madc.c | 537 +++++ >> drivers/misc/ti-st/st_core.c | 355 +-- >> drivers/misc/ti-st/st_kim.c | 56 +- >> drivers/mmc/card/block.c | 4 +- >> drivers/mtd/nand/nand_ecc.c | 2 +- >> drivers/net/smsc911x.c | 4 +- >> drivers/net/wireless/wl12xx/Kconfig | 10 + >> drivers/net/wireless/wl12xx/wl1271.h | 11 +- >> drivers/net/wireless/wl12xx/wl1271_acx.c | 83 + >> drivers/net/wireless/wl12xx/wl1271_acx.h | 86 + >> drivers/net/wireless/wl12xx/wl1271_main.c | 161 +- >> drivers/net/wireless/wl12xx/wl1271_rx.c | 6 + >> drivers/net/wireless/wl12xx/wl1271_tx.c | 11 + >> drivers/rtc/rtc-twl.c | 25 + >> drivers/serial/omap-serial.c | 4 + >> drivers/video/modedb.c | 4 + >> drivers/video/omap2/displays/Kconfig | 12 + >> drivers/video/omap2/displays/Makefile | 2 + >> .../omap2/displays/panel-lgphilips-lb035q02.c | 244 ++ >> .../omap2/displays/panel-samsung-lte430wq-f0c.c | 154 ++ >> drivers/video/omap2/dss/dispc.c | 4 +- >> drivers/video/omap2/dss/dpi.c | 7 +- >> drivers/video/omap2/dss/venc.c | 22 + >> drivers/video/omap2/omapfb/omapfb-main.c | 10 +- >> fs/buffer.c | 3 +- >> include/linux/Kbuild | 4 + >> include/linux/i2c/twl.h | 1 + >> include/linux/i2c/twl4030-madc.h | 130 + >> include/linux/media.h | 132 ++ >> include/linux/omap3isp.h | 631 +++++ >> include/linux/opp.h | 8 + >> include/linux/ti_wilink_st.h | 40 +- >> include/linux/usb/ehci_def.h | 6 +- >> include/linux/v4l2-mediabus.h | 108 + >> include/linux/v4l2-subdev.h | 141 ++ >> include/linux/videodev2.h | 4 + >> include/media/media-device.h | 95 + >> include/media/media-devnode.h | 97 + >> include/media/media-entity.h | 147 ++ >> include/media/soc_mediabus.h | 3 +- >> include/media/v4l2-common.h | 18 +- >> include/media/v4l2-ctrls.h | 1 + >> include/media/v4l2-dev.h | 25 +- >> include/media/v4l2-device.h | 4 + >> include/media/v4l2-ioctl.h | 3 + >> include/media/v4l2-mediabus.h | 61 +- >> include/media/v4l2-subdev.h | 120 +- >> net/bridge/br_stp_bpdu.c | 2 + >> sound/soc/codecs/twl4030.c | 4 +- >> sound/soc/omap/omap-mcbsp.c | 3 + 178 >> files changed, 37220 insertions(+), 745 deletions(-) create mode >> 100644 Documentation/ABI/testing/sysfs-bus-media create mode 100644 >> Documentation/DocBook/v4l/dev-subdev.xml create mode 100644 >> Documentation/DocBook/v4l/media-controller.xml create mode 100644 >> Documentation/DocBook/v4l/media-func-close.xml create mode 100644 >> Documentation/DocBook/v4l/media-func-ioctl.xml create mode 100644 >> Documentation/DocBook/v4l/media-func-open.xml create mode 100644 >> Documentation/DocBook/v4l/media-ioc-device-info.xml create mode >> 100644 Documentation/DocBook/v4l/media-ioc-enum-entities.xml create >> mode 100644 Documentation/DocBook/v4l/media-ioc-enum-links.xml >> create mode 100644 >> Documentation/DocBook/v4l/media-ioc-setup-link.xml create mode >> 100644 Documentation/DocBook/v4l/subdev-formats.xml create mode >> 100644 >> Documentation/DocBook/v4l/vidioc-subdev-enum-frame-interval.xml >> create mode 100644 >> Documentation/DocBook/v4l/vidioc-subdev-enum-frame-size.xml create >> mode 100644 >> Documentation/DocBook/v4l/vidioc-subdev-enum-mbus-code.xml create >> mode 100644 Documentation/DocBook/v4l/vidioc-subdev-g-crop.xml >> create mode 100644 >> Documentation/DocBook/v4l/vidioc-subdev-g-fmt.xml create mode >> 100644 >> Documentation/DocBook/v4l/vidioc-subdev-g-frame-interval.xml create >> mode 100644 Documentation/media-framework.txt create mode 100644 >> arch/arm/mach-omap2/devices.h create mode 100644 >> drivers/bluetooth/btwilink.c create mode 100644 >> drivers/media/media-device.c create mode 100644 >> drivers/media/media-devnode.c create mode 100644 >> drivers/media/media-entity.c create mode 100644 >> drivers/media/radio/wl128x/Kconfig create mode 100644 >> drivers/media/radio/wl128x/Makefile create mode 100644 >> drivers/media/radio/wl128x/fmdrv.h create mode 100644 >> drivers/media/radio/wl128x/fmdrv_common.c create mode 100644 >> drivers/media/radio/wl128x/fmdrv_common.h create mode 100644 >> drivers/media/radio/wl128x/fmdrv_rx.c create mode 100644 >> drivers/media/radio/wl128x/fmdrv_rx.h create mode 100644 >> drivers/media/radio/wl128x/fmdrv_tx.c create mode 100644 >> drivers/media/radio/wl128x/fmdrv_tx.h create mode 100644 >> drivers/media/radio/wl128x/fmdrv_v4l2.c create mode 100644 >> drivers/media/radio/wl128x/fmdrv_v4l2.h create mode 100644 >> drivers/media/video/isp/Makefile create mode 100644 >> drivers/media/video/isp/cfa_coef_table.h create mode 100644 >> drivers/media/video/isp/gamma_table.h create mode 100644 >> drivers/media/video/isp/isp.c create mode 100644 >> drivers/media/video/isp/isp.h create mode 100644 >> drivers/media/video/isp/ispccdc.c create mode 100644 >> drivers/media/video/isp/ispccdc.h create mode 100644 >> drivers/media/video/isp/ispccp2.c create mode 100644 >> drivers/media/video/isp/ispccp2.h create mode 100644 >> drivers/media/video/isp/ispcsi2.c create mode 100644 >> drivers/media/video/isp/ispcsi2.h create mode 100644 >> drivers/media/video/isp/ispcsiphy.c create mode 100644 >> drivers/media/video/isp/ispcsiphy.h create mode 100644 >> drivers/media/video/isp/isph3a.h create mode 100644 >> drivers/media/video/isp/isph3a_aewb.c create mode 100644 >> drivers/media/video/isp/isph3a_af.c create mode 100644 >> drivers/media/video/isp/isphist.c create mode 100644 >> drivers/media/video/isp/isphist.h create mode 100644 >> drivers/media/video/isp/isppreview.c create mode 100644 >> drivers/media/video/isp/isppreview.h create mode 100644 >> drivers/media/video/isp/ispqueue.c create mode 100644 >> drivers/media/video/isp/ispqueue.h create mode 100644 >> drivers/media/video/isp/ispreg.h create mode 100644 >> drivers/media/video/isp/ispresizer.c create mode 100644 >> drivers/media/video/isp/ispresizer.h create mode 100644 >> drivers/media/video/isp/ispstat.c create mode 100644 >> drivers/media/video/isp/ispstat.h create mode 100644 >> drivers/media/video/isp/ispvideo.c create mode 100644 >> drivers/media/video/isp/ispvideo.h create mode 100644 >> drivers/media/video/isp/luma_enhance_table.h create mode 100644 >> drivers/media/video/isp/noise_filter_table.h create mode 100644 >> drivers/media/video/v4l2-subdev.c create mode 100644 >> drivers/mfd/twl4030-madc.c create mode 100644 >> drivers/video/omap2/displays/panel-lgphilips-lb035q02.c create mode >> 100644 drivers/video/omap2/displays/panel-samsung-lte430wq-f0c.c >> create mode 100644 include/linux/i2c/twl4030-madc.h create mode >> 100644 include/linux/media.h create mode 100644 >> include/linux/omap3isp.h create mode 100644 >> include/linux/v4l2-mediabus.h create mode 100644 >> include/linux/v4l2-subdev.h create mode 100644 >> include/media/media-device.h create mode 100644 >> include/media/media-devnode.h create mode 100644 >> include/media/media-entity.h >> >> _______________________________________________ yocto mailing list >> yocto@yoctoproject.org >> https://lists.yoctoproject.org/listinfo/yocto > -- Darren Hart Intel Open Source Technology Center Yocto Project - Linux Kernel ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PULL][linux-yocto] beagleboard: sync with meta-ti linux-omap_2.6.37 2011-06-18 15:08 ` Darren Hart @ 2011-06-18 15:10 ` Koen Kooi 2011-06-18 15:13 ` Koen Kooi 0 siblings, 1 reply; 9+ messages in thread From: Koen Kooi @ 2011-06-18 15:10 UTC (permalink / raw) To: Darren Hart; +Cc: yocto Project Op 18 jun 2011, om 17:08 heeft Darren Hart het volgende geschreven: > > > On 06/18/2011 01:11 AM, Koen Kooi wrote: >> >> Op 18 jun 2011, om 01:18 heeft Darren Hart het volgende geschreven: >> >>> From: Darren Hart <dvhart@linux.intel.com> >>> >>> The following commits have been pulled in from the meta-ti >>> linux-omap_2.6.37 recipe, with the exception of: USB: ehci: remove >>> structure packing from ehci_def which hails from mainline and >>> should be applied to yocto/base, while the rest should be applied >>> to yocto/standard/beagleboard. >>> >>> Fixes [YOCTO #764] Fixes [YOCTO #765] Fixes [YOCTO #767] >>> >>> This brings linux-yocto in sync with the meta-ti linux-omap_2.6.37 >>> recipe and significantly improves Beagleboard support in >>> linux-yocto. As there are 115 patches in total, and none of them >>> are new, I have omitted them from the email. >> >> >> You seem to be including the patches that patch the kernel from >> 37rc7 (or rc8, I forget) to .37 final, which shouldn't apply. So >> basically leave out the patches in the 'linus' directory. > > There were about 200 patches in total, I've removed all those that > reverse applied and failed do to a conflict that was obviously a merge > of a very similar patch. That accounted for most of the 37-rc[78] to 37 > patches from the linus directory. > >> The camera >> interface also doesn't work, so the 'media' directory can be left out >> as well. > > The goal was to stay as close to the meta-ti/linux-omap_2.6.37 recipe as > possible with the linux-yocto kernel repository. Will you be removing > all of the media directory from there as well? I don't want to remove > them from here if you'll be *adding* to them there. However, if you'll > be sure to just be replacing them there, then I can drop them here. The .37 isn't used, developed or supported for beagleboard anymore, .39 is all the rage now :) ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PULL][linux-yocto] beagleboard: sync with meta-ti linux-omap_2.6.37 2011-06-18 15:10 ` Koen Kooi @ 2011-06-18 15:13 ` Koen Kooi 2011-06-18 16:09 ` Bruce Ashfield 0 siblings, 1 reply; 9+ messages in thread From: Koen Kooi @ 2011-06-18 15:13 UTC (permalink / raw) To: Darren Hart; +Cc: yocto Project Op 18 jun 2011, om 17:10 heeft Koen Kooi het volgende geschreven: > > Op 18 jun 2011, om 17:08 heeft Darren Hart het volgende geschreven: > >> >> >> On 06/18/2011 01:11 AM, Koen Kooi wrote: >>> >>> Op 18 jun 2011, om 01:18 heeft Darren Hart het volgende geschreven: >>> >>>> From: Darren Hart <dvhart@linux.intel.com> >>>> >>>> The following commits have been pulled in from the meta-ti >>>> linux-omap_2.6.37 recipe, with the exception of: USB: ehci: remove >>>> structure packing from ehci_def which hails from mainline and >>>> should be applied to yocto/base, while the rest should be applied >>>> to yocto/standard/beagleboard. >>>> >>>> Fixes [YOCTO #764] Fixes [YOCTO #765] Fixes [YOCTO #767] >>>> >>>> This brings linux-yocto in sync with the meta-ti linux-omap_2.6.37 >>>> recipe and significantly improves Beagleboard support in >>>> linux-yocto. As there are 115 patches in total, and none of them >>>> are new, I have omitted them from the email. >>> >>> >>> You seem to be including the patches that patch the kernel from >>> 37rc7 (or rc8, I forget) to .37 final, which shouldn't apply. So >>> basically leave out the patches in the 'linus' directory. >> >> There were about 200 patches in total, I've removed all those that >> reverse applied and failed do to a conflict that was obviously a merge >> of a very similar patch. That accounted for most of the 37-rc[78] to 37 >> patches from the linus directory. >> >>> The camera >>> interface also doesn't work, so the 'media' directory can be left out >>> as well. >> >> The goal was to stay as close to the meta-ti/linux-omap_2.6.37 recipe as >> possible with the linux-yocto kernel repository. Will you be removing >> all of the media directory from there as well? I don't want to remove >> them from here if you'll be *adding* to them there. However, if you'll >> be sure to just be replacing them there, then I can drop them here. > > The .37 isn't used, developed or supported for beagleboard anymore, .39 is all the rage now :) Speaking of .39, is there a 'linux-yocto' type of tree for .39 mainline with a skeleton for machine support? If there is, I'd like to fork it to see if it can improve my current workflow which consist of self written scripts that emulate guilt. ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PULL][linux-yocto] beagleboard: sync with meta-ti linux-omap_2.6.37 2011-06-18 15:13 ` Koen Kooi @ 2011-06-18 16:09 ` Bruce Ashfield 2011-06-18 16:32 ` Koen Kooi 0 siblings, 1 reply; 9+ messages in thread From: Bruce Ashfield @ 2011-06-18 16:09 UTC (permalink / raw) To: Koen Kooi; +Cc: yocto Project, Darren Hart On 11-06-18 11:13 AM, Koen Kooi wrote: > > Op 18 jun 2011, om 17:10 heeft Koen Kooi het volgende geschreven: > >> >> Op 18 jun 2011, om 17:08 heeft Darren Hart het volgende geschreven: >> >>> >>> >>> On 06/18/2011 01:11 AM, Koen Kooi wrote: >>>> >>>> Op 18 jun 2011, om 01:18 heeft Darren Hart het volgende geschreven: >>>> >>>>> From: Darren Hart<dvhart@linux.intel.com> >>>>> >>>>> The following commits have been pulled in from the meta-ti >>>>> linux-omap_2.6.37 recipe, with the exception of: USB: ehci: remove >>>>> structure packing from ehci_def which hails from mainline and >>>>> should be applied to yocto/base, while the rest should be applied >>>>> to yocto/standard/beagleboard. >>>>> >>>>> Fixes [YOCTO #764] Fixes [YOCTO #765] Fixes [YOCTO #767] >>>>> >>>>> This brings linux-yocto in sync with the meta-ti linux-omap_2.6.37 >>>>> recipe and significantly improves Beagleboard support in >>>>> linux-yocto. As there are 115 patches in total, and none of them >>>>> are new, I have omitted them from the email. >>>> >>>> >>>> You seem to be including the patches that patch the kernel from >>>> 37rc7 (or rc8, I forget) to .37 final, which shouldn't apply. So >>>> basically leave out the patches in the 'linus' directory. >>> >>> There were about 200 patches in total, I've removed all those that >>> reverse applied and failed do to a conflict that was obviously a merge >>> of a very similar patch. That accounted for most of the 37-rc[78] to 37 >>> patches from the linus directory. >>> >>>> The camera >>>> interface also doesn't work, so the 'media' directory can be left out >>>> as well. >>> >>> The goal was to stay as close to the meta-ti/linux-omap_2.6.37 recipe as >>> possible with the linux-yocto kernel repository. Will you be removing >>> all of the media directory from there as well? I don't want to remove >>> them from here if you'll be *adding* to them there. However, if you'll >>> be sure to just be replacing them there, then I can drop them here. >> >> The .37 isn't used, developed or supported for beagleboard anymore, .39 is all the rage now :) > > Speaking of .39, is there a 'linux-yocto' type of tree for .39 mainline with a skeleton for machine support? If there is, I'd like to fork it to see if it can improve my current workflow which consist of self written scripts that emulate guilt. I've got the linux-yocto-dev recipe in poky-extras, meta-kernel-dev layer. That recipe tracked 2.6.39, and has now jumped to 3.0 (with a minor cheat as I work through the 3.0 naming issues). The kernel repo is hosted on git.yoctoproject.org as the linux-yocto-dev repo. The repo is fast forward for a given version, and then is re-generated when I jump it from version to version. I carry forward all the existing patches and keep the qemu machines working. Although at the moment, qemuppc is losing interrupts and can't get past init :) That's also the repo where I'm testing out some changes to kern-tools (but they are stable), which will show up shortly. Cheers, Bruce > ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PULL][linux-yocto] beagleboard: sync with meta-ti linux-omap_2.6.37 2011-06-18 16:09 ` Bruce Ashfield @ 2011-06-18 16:32 ` Koen Kooi 2011-06-20 19:46 ` Bruce Ashfield 0 siblings, 1 reply; 9+ messages in thread From: Koen Kooi @ 2011-06-18 16:32 UTC (permalink / raw) To: Bruce Ashfield; +Cc: yocto Project, Darren Hart Op 18 jun 2011, om 18:09 heeft Bruce Ashfield het volgende geschreven: > On 11-06-18 11:13 AM, Koen Kooi wrote: >> >> Op 18 jun 2011, om 17:10 heeft Koen Kooi het volgende geschreven: >> >>> >>> Op 18 jun 2011, om 17:08 heeft Darren Hart het volgende geschreven: >>> >>>> >>>> >>>> On 06/18/2011 01:11 AM, Koen Kooi wrote: >>>>> >>>>> Op 18 jun 2011, om 01:18 heeft Darren Hart het volgende geschreven: >>>>> >>>>>> From: Darren Hart<dvhart@linux.intel.com> >>>>>> >>>>>> The following commits have been pulled in from the meta-ti >>>>>> linux-omap_2.6.37 recipe, with the exception of: USB: ehci: remove >>>>>> structure packing from ehci_def which hails from mainline and >>>>>> should be applied to yocto/base, while the rest should be applied >>>>>> to yocto/standard/beagleboard. >>>>>> >>>>>> Fixes [YOCTO #764] Fixes [YOCTO #765] Fixes [YOCTO #767] >>>>>> >>>>>> This brings linux-yocto in sync with the meta-ti linux-omap_2.6.37 >>>>>> recipe and significantly improves Beagleboard support in >>>>>> linux-yocto. As there are 115 patches in total, and none of them >>>>>> are new, I have omitted them from the email. >>>>> >>>>> >>>>> You seem to be including the patches that patch the kernel from >>>>> 37rc7 (or rc8, I forget) to .37 final, which shouldn't apply. So >>>>> basically leave out the patches in the 'linus' directory. >>>> >>>> There were about 200 patches in total, I've removed all those that >>>> reverse applied and failed do to a conflict that was obviously a merge >>>> of a very similar patch. That accounted for most of the 37-rc[78] to 37 >>>> patches from the linus directory. >>>> >>>>> The camera >>>>> interface also doesn't work, so the 'media' directory can be left out >>>>> as well. >>>> >>>> The goal was to stay as close to the meta-ti/linux-omap_2.6.37 recipe as >>>> possible with the linux-yocto kernel repository. Will you be removing >>>> all of the media directory from there as well? I don't want to remove >>>> them from here if you'll be *adding* to them there. However, if you'll >>>> be sure to just be replacing them there, then I can drop them here. >>> >>> The .37 isn't used, developed or supported for beagleboard anymore, .39 is all the rage now :) >> >> Speaking of .39, is there a 'linux-yocto' type of tree for .39 mainline with a skeleton for machine support? If there is, I'd like to fork it to see if it can improve my current workflow which consist of self written scripts that emulate guilt. > > I've got the linux-yocto-dev recipe in poky-extras, meta-kernel-dev > layer. That recipe tracked 2.6.39, and has now jumped to 3.0 (with > a minor cheat as I work through the 3.0 naming issues). The kernel > repo is hosted on git.yoctoproject.org as the linux-yocto-dev repo. > > The repo is fast forward for a given version, and then is re-generated > when I jump it from version to version. I carry forward all the existing > patches and keep the qemu machines working. Although at the moment, > qemuppc is losing interrupts and can't get past init :) > > That's also the repo where I'm testing out some changes to kern-tools > (but they are stable), which will show up shortly. Thanks, I'll have a look at that. Is there already some doc out on how to create such a structure from scratch? ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PULL][linux-yocto] beagleboard: sync with meta-ti linux-omap_2.6.37 2011-06-18 16:32 ` Koen Kooi @ 2011-06-20 19:46 ` Bruce Ashfield 2011-06-20 19:48 ` Koen Kooi 0 siblings, 1 reply; 9+ messages in thread From: Bruce Ashfield @ 2011-06-20 19:46 UTC (permalink / raw) To: Koen Kooi; +Cc: yocto Project, Darren Hart On 06/18/11 12:32, Koen Kooi wrote: > > Op 18 jun 2011, om 18:09 heeft Bruce Ashfield het volgende geschreven: > >> On 11-06-18 11:13 AM, Koen Kooi wrote: >>> >>> Op 18 jun 2011, om 17:10 heeft Koen Kooi het volgende geschreven: >>> >>>> >>>> Op 18 jun 2011, om 17:08 heeft Darren Hart het volgende geschreven: >>>> >>>>> >>>>> >>>>> On 06/18/2011 01:11 AM, Koen Kooi wrote: >>>>>> >>>>>> Op 18 jun 2011, om 01:18 heeft Darren Hart het volgende geschreven: >>>>>> >>>>>>> From: Darren Hart<dvhart@linux.intel.com> >>>>>>> >>>>>>> The following commits have been pulled in from the meta-ti >>>>>>> linux-omap_2.6.37 recipe, with the exception of: USB: ehci: remove >>>>>>> structure packing from ehci_def which hails from mainline and >>>>>>> should be applied to yocto/base, while the rest should be applied >>>>>>> to yocto/standard/beagleboard. >>>>>>> >>>>>>> Fixes [YOCTO #764] Fixes [YOCTO #765] Fixes [YOCTO #767] >>>>>>> >>>>>>> This brings linux-yocto in sync with the meta-ti linux-omap_2.6.37 >>>>>>> recipe and significantly improves Beagleboard support in >>>>>>> linux-yocto. As there are 115 patches in total, and none of them >>>>>>> are new, I have omitted them from the email. >>>>>> >>>>>> >>>>>> You seem to be including the patches that patch the kernel from >>>>>> 37rc7 (or rc8, I forget) to .37 final, which shouldn't apply. So >>>>>> basically leave out the patches in the 'linus' directory. >>>>> >>>>> There were about 200 patches in total, I've removed all those that >>>>> reverse applied and failed do to a conflict that was obviously a merge >>>>> of a very similar patch. That accounted for most of the 37-rc[78] to 37 >>>>> patches from the linus directory. >>>>> >>>>>> The camera >>>>>> interface also doesn't work, so the 'media' directory can be left out >>>>>> as well. >>>>> >>>>> The goal was to stay as close to the meta-ti/linux-omap_2.6.37 recipe as >>>>> possible with the linux-yocto kernel repository. Will you be removing >>>>> all of the media directory from there as well? I don't want to remove >>>>> them from here if you'll be *adding* to them there. However, if you'll >>>>> be sure to just be replacing them there, then I can drop them here. >>>> >>>> The .37 isn't used, developed or supported for beagleboard anymore, .39 is all the rage now :) >>> >>> Speaking of .39, is there a 'linux-yocto' type of tree for .39 mainline with a skeleton for machine support? If there is, I'd like to fork it to see if it can improve my current workflow which consist of self written scripts that emulate guilt. >> >> I've got the linux-yocto-dev recipe in poky-extras, meta-kernel-dev >> layer. That recipe tracked 2.6.39, and has now jumped to 3.0 (with >> a minor cheat as I work through the 3.0 naming issues). The kernel >> repo is hosted on git.yoctoproject.org as the linux-yocto-dev repo. >> >> The repo is fast forward for a given version, and then is re-generated >> when I jump it from version to version. I carry forward all the existing >> patches and keep the qemu machines working. Although at the moment, >> qemuppc is losing interrupts and can't get past init :) >> >> That's also the repo where I'm testing out some changes to kern-tools >> (but they are stable), which will show up shortly. > > Thanks, I'll have a look at that. Is there already some doc out on how to create such a structure from scratch? At the moment, they are carried forward from kernel version to kernel version and then interpreted by the tools. But I do have some notes and other information that describe how to take upstream tree <foo>, feed it a kernel-cache (what you see in the meta branch) and create a new kernel tree ready to build. I've got to get a bit of 3.0-rcX behind me, but I'm writing this up and will contribute it, if that's what you are thinking of here. Cheers, Bruce ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PULL][linux-yocto] beagleboard: sync with meta-ti linux-omap_2.6.37 2011-06-20 19:46 ` Bruce Ashfield @ 2011-06-20 19:48 ` Koen Kooi 0 siblings, 0 replies; 9+ messages in thread From: Koen Kooi @ 2011-06-20 19:48 UTC (permalink / raw) To: Bruce Ashfield; +Cc: yocto Project, Darren Hart Op 20 jun 2011, om 21:46 heeft Bruce Ashfield het volgende geschreven: > On 06/18/11 12:32, Koen Kooi wrote: >> >> Op 18 jun 2011, om 18:09 heeft Bruce Ashfield het volgende geschreven: >> >>> On 11-06-18 11:13 AM, Koen Kooi wrote: >>>> >>>> Op 18 jun 2011, om 17:10 heeft Koen Kooi het volgende geschreven: >>>> >>>>> >>>>> Op 18 jun 2011, om 17:08 heeft Darren Hart het volgende geschreven: >>>>> >>>>>> >>>>>> >>>>>> On 06/18/2011 01:11 AM, Koen Kooi wrote: >>>>>>> >>>>>>> Op 18 jun 2011, om 01:18 heeft Darren Hart het volgende geschreven: >>>>>>> >>>>>>>> From: Darren Hart<dvhart@linux.intel.com> >>>>>>>> >>>>>>>> The following commits have been pulled in from the meta-ti >>>>>>>> linux-omap_2.6.37 recipe, with the exception of: USB: ehci: remove >>>>>>>> structure packing from ehci_def which hails from mainline and >>>>>>>> should be applied to yocto/base, while the rest should be applied >>>>>>>> to yocto/standard/beagleboard. >>>>>>>> >>>>>>>> Fixes [YOCTO #764] Fixes [YOCTO #765] Fixes [YOCTO #767] >>>>>>>> >>>>>>>> This brings linux-yocto in sync with the meta-ti linux-omap_2.6.37 >>>>>>>> recipe and significantly improves Beagleboard support in >>>>>>>> linux-yocto. As there are 115 patches in total, and none of them >>>>>>>> are new, I have omitted them from the email. >>>>>>> >>>>>>> >>>>>>> You seem to be including the patches that patch the kernel from >>>>>>> 37rc7 (or rc8, I forget) to .37 final, which shouldn't apply. So >>>>>>> basically leave out the patches in the 'linus' directory. >>>>>> >>>>>> There were about 200 patches in total, I've removed all those that >>>>>> reverse applied and failed do to a conflict that was obviously a merge >>>>>> of a very similar patch. That accounted for most of the 37-rc[78] to 37 >>>>>> patches from the linus directory. >>>>>> >>>>>>> The camera >>>>>>> interface also doesn't work, so the 'media' directory can be left out >>>>>>> as well. >>>>>> >>>>>> The goal was to stay as close to the meta-ti/linux-omap_2.6.37 recipe as >>>>>> possible with the linux-yocto kernel repository. Will you be removing >>>>>> all of the media directory from there as well? I don't want to remove >>>>>> them from here if you'll be *adding* to them there. However, if you'll >>>>>> be sure to just be replacing them there, then I can drop them here. >>>>> >>>>> The .37 isn't used, developed or supported for beagleboard anymore, .39 is all the rage now :) >>>> >>>> Speaking of .39, is there a 'linux-yocto' type of tree for .39 mainline with a skeleton for machine support? If there is, I'd like to fork it to see if it can improve my current workflow which consist of self written scripts that emulate guilt. >>> >>> I've got the linux-yocto-dev recipe in poky-extras, meta-kernel-dev >>> layer. That recipe tracked 2.6.39, and has now jumped to 3.0 (with >>> a minor cheat as I work through the 3.0 naming issues). The kernel >>> repo is hosted on git.yoctoproject.org as the linux-yocto-dev repo. >>> >>> The repo is fast forward for a given version, and then is re-generated >>> when I jump it from version to version. I carry forward all the existing >>> patches and keep the qemu machines working. Although at the moment, >>> qemuppc is losing interrupts and can't get past init :) >>> >>> That's also the repo where I'm testing out some changes to kern-tools >>> (but they are stable), which will show up shortly. >> >> Thanks, I'll have a look at that. Is there already some doc out on how to create such a structure from scratch? > > At the moment, they are carried forward from kernel version > to kernel version and then interpreted by the tools. But I > do have some notes and other information that describe how to > take upstream tree <foo>, feed it a kernel-cache (what you see > in the meta branch) and create a new kernel tree ready to > build. > > I've got to get a bit of 3.0-rcX behind me, but I'm writing this > up and will contribute it, if that's what you are thinking > of here. That's exactly what I'm thinking of! ^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2011-06-20 19:48 UTC | newest] Thread overview: 9+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2011-06-17 23:18 [PULL][linux-yocto] beagleboard: sync with meta-ti linux-omap_2.6.37 Darren Hart 2011-06-18 8:11 ` Koen Kooi 2011-06-18 15:08 ` Darren Hart 2011-06-18 15:10 ` Koen Kooi 2011-06-18 15:13 ` Koen Kooi 2011-06-18 16:09 ` Bruce Ashfield 2011-06-18 16:32 ` Koen Kooi 2011-06-20 19:46 ` Bruce Ashfield 2011-06-20 19:48 ` Koen Kooi
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.