From: Darren Hart <dvhart@linux.intel.com>
To: Darren Hart <darren@dvhart.com>
Cc: yocto@yoctoproject.org
Subject: Re: [PULL v2][linux-yocto]beagleboard: sync with meta-ti linux-omap_2.6.37
Date: Tue, 21 Jun 2011 00:23:09 -0700 [thread overview]
Message-ID: <4E0046DD.4080101@linux.intel.com> (raw)
In-Reply-To: <cover.1308639936.git.dvhart@linux.intel.com>
On 06/21/2011 12:17 AM, Darren Hart wrote:
> From: Darren Hart <dvhart@linux.intel.com>
>
> The following commits have been pulled in from the meta-ti linux-omap_2.6.37
> recipe, with the exception of:
> USB: ehci: remove structure packing from ehci_def
> which hails from mainline and should be applied to yocto/base, while the rest
> should be applied to yocto/standard/beagleboard.
>
> Fixes [YOCTO #764]
> Fixes [YOCTO #765]
> Fixes [YOCTO #767]
>
> This brings linux-yocto in sync with the meta-ti linux-omap_2.6.37 recipe and
> significantly improves Beagleboard support in linux-yocto. As there are 70
> patches in total, and none of them are new, I have omitted them from the email.
>
> V2: Eliminate the linus/* (3) and media/* (42) patches at Koon's suggestion,
> reducing patch count from 115 to 70.
>
> The following changes since commit bd97d3f257387a3659b5c2761b0d5323b65203c7:
>
> Merge branch 'yocto/standard/base' into yocto/standard/beagleboard (2011-06-16 15:54:07 -0400)
>
> are available in the git repository at:
>
> git://git.yoctoproject.org/linux-yocto-2.6.37-contrib dvhart/yocto/standard/beagleboard
> http://git.yoctoproject.org/cgit.cgi/linux-yocto-2.6.37-contrib/log/?h=dvhart/yocto/standard/beagleboard
Note: this applies cleanly to yocto/standard/beagleboard. As this is a
reset to a pretty different BSP kernel source, I had planned to base it
off of yocto/standard/base - but it turns out we didn't have any source
changes in the beagleboard branch, so there was no need.
--
Darren
>
> Alexander Holler (1):
> arm: omap3: beagle: Ensure msecure is mux'd to be able to set the RTC
>
> Arik Nemtsov (1):
> wl12xx: Read MAC address from NVS file on HW startup
>
> Darren Hart (2):
> board-omap3beagle: whitespace cleanup
> board-omap3beagle: allow for building without wl1271
>
> Eliad Peller (1):
> wl1271: set wl->vif only if add_interface succeeded.
>
> Juuso Oikarinen (1):
> wl12xx: Unset bssid filter, ssid and bssid from firmware on disassoc
>
> Kevin Hilman (1):
> OMAP: CPUfreq: ensure policy is fully initialized
>
> Koen Kooi (10):
> omap3: beaglexm: fix DVI reset GPIO
> omap3: beaglexm: fix power on of DVI
> ARM: OMAP: beagleboard: Add infrastructure to do fixups based on
> expansionboard name passed by u-boot
> ARM: OMAP: beagleboard: pre-export GPIOs to userspace when using a
> Tincantools trainerboard
> modedb.c: add proper 720p60 mode
> ARM: OMAP: add omap_rev_* macros
> omap3: beagleboard: add WIP support for beagleboardtoys WL12xx board
> beagleboard: hack in support from xM rev C
> omap3: allow 1GHz mpurates
> BeagleBoard: Adjust USER button pin for xM
>
> Manjunatha Halli (7):
> drivers:media:radio: wl128x: FM Driver common header file
> drivers:media:radio: wl128x: FM Driver V4L2 sources
> drivers:media:radio: wl128x: FM Driver Common sources
> drivers:media:radio: wl128x: FM driver RX sources
> drivers:media:radio: wl128x: FM driver TX sources
> drivers:media:radio: wl128x: Kconfig & Makefile for wl128x driver
> drivers:media:radio: Update Kconfig and Makefile for wl128x FM
> driver.
>
> Nishanth Menon (2):
> omap3|4: opp: make omapx_opp_init non-static
> OMAP3: beagle xm: enable upto 1GHz OPP
>
> Pavan Savoy (2):
> drivers:misc:ti-st: change protocol parse logic
> Bluetooth: btwilink driver
>
> Peter 'p2' De Schrijver (1):
> OMAP: CPUfreq: ensure driver initializes after cpufreq framework and
> governors
>
> Rabin Vincent (1):
> USB: ehci: remove structure packing from ehci_def
>
> Rajendra Nayak (1):
> OMAP3 PM: CPUFreq driver for OMAP3
>
> Robert Nelson (2):
> omap: Beagle: detect new xM revision B
> xM audio fix from Ashok
>
> Sanjeev Premi (1):
> omap3: Add basic support for 720MHz part
>
> Shahar Levi (3):
> wl1271: 11n Support, Add Definitions
> wl1271: 11n Support, ACX Commands
> wl1271: 11n Support, functionality and configuration ability
>
> Silesh C V (1):
> OMAP: PM: CPUFREQ: Fix conditional compilation
>
> Steve Sakoman (18):
> mmc: don't display single block read console messages
> MTD: silence ecc errors on mtdblock0
> OMAP: DSS2: enable hsclk in dsi_pll_init for OMAP36XX
> drivers: net: smsc911x: return ENODEV if device is not found
> drivers: input: touchscreen: ads7846: return ENODEV if device is not
> found
> ASoC: enable audio capture by default for twl4030
> MFD: enable madc clock
> MFD: add twl4030 madc driver
> ARM: OMAP: Add twl4030 madc support to Overo
> ARM: OMAP: Add twl4030 madc support to Beagle
> OMAP: DSS2: Add support for Samsung LTE430WQ-F0C panel
> OMAP: DSS2: Add support for LG Philips LB035Q02 panel
> OMAP: DSS2: add bootarg for selecting svideo or composite for tv
> output
> ARM: OMAP2: mmc-twl4030: move clock input selection prior to vcc test
> RTC: add support for backup battery recharge
> ARM: OMAP: automatically set musb mode in platform data based on
> CONFIG options
> OMAP: DSS2: check for both cpu type and revision, rather than just
> revision
> OMAP: DSS2: Add DSS2 support for Overo
>
> Thara Gopinath (13):
> OMAP3: PM: Adding T2 enabling of smartreflex
> OMAP: Introduce a user list for each voltage domain instance in the
> voltage driver.
> OMAP: Introduce API in the OPP layer to find the opp entry
> corresponding to a voltage.
> OMAP: Introduce API to register a device with a voltagedomain
> OMAP: Introduce device specific set rate and get rate in omap_device
> structure
> OMAP: Voltage layer changes to support DVFS.
> OMAP: Introduce dependent voltage domain support.
> OMAP: Introduce device scale
> OMAP: Disable smartreflex across DVFS
> OMAP3: Introduce custom set rate and get rate APIs for scalable
> devices
> OMAP3: Update cpufreq driver to use the new set_rate API
> OMAP3: Introduce voltage domain info in the hwmod structures.
> OMAP3: Add voltage dependency table for VDD1.
>
> Thomas Weber (1):
> OMAP: Enable Magic SysRq on serial console ttyOx
>
> arch/arm/mach-omap2/board-omap3beagle.c | 409 +++++-
> arch/arm/mach-omap2/board-overo.c | 247 +++-
> arch/arm/mach-omap2/clock.h | 14 +-
> arch/arm/mach-omap2/clock34xx.c | 2 +
> arch/arm/mach-omap2/control.h | 7 +
> arch/arm/mach-omap2/hsmmc.c | 14 +-
> arch/arm/mach-omap2/id.c | 10 +
> arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 3 +
> arch/arm/mach-omap2/omap_twl.c | 16 +
> arch/arm/mach-omap2/opp3xxx_data.c | 66 +-
> arch/arm/mach-omap2/opp4xxx_data.c | 3 +-
> arch/arm/mach-omap2/pm.c | 110 ++
> arch/arm/mach-omap2/voltage.c | 369 +++++-
> arch/arm/plat-omap/clock.c | 2 +-
> arch/arm/plat-omap/cpu-omap.c | 38 +-
> arch/arm/plat-omap/include/plat/cpu.h | 57 +
> arch/arm/plat-omap/include/plat/omap_device.h | 12 +-
> arch/arm/plat-omap/include/plat/voltage.h | 20 +
> arch/arm/plat-omap/omap_device.c | 139 ++
> block/blk-core.c | 7 +-
> drivers/base/power/opp.c | 28 +
> drivers/bluetooth/Kconfig | 10 +
> drivers/bluetooth/Makefile | 1 +
> drivers/bluetooth/btwilink.c | 397 +++++
> drivers/input/touchscreen/ads7846.c | 13 +-
> drivers/media/radio/Kconfig | 3 +
> drivers/media/radio/Makefile | 1 +
> drivers/media/radio/wl128x/Kconfig | 17 +
> drivers/media/radio/wl128x/Makefile | 6 +
> drivers/media/radio/wl128x/fmdrv.h | 244 +++
> drivers/media/radio/wl128x/fmdrv_common.c | 1677 ++++++++++++++++++++
> drivers/media/radio/wl128x/fmdrv_common.h | 402 +++++
> drivers/media/radio/wl128x/fmdrv_rx.c | 847 ++++++++++
> drivers/media/radio/wl128x/fmdrv_rx.h | 59 +
> drivers/media/radio/wl128x/fmdrv_tx.c | 425 +++++
> drivers/media/radio/wl128x/fmdrv_tx.h | 37 +
> drivers/media/radio/wl128x/fmdrv_v4l2.c | 580 +++++++
> drivers/media/radio/wl128x/fmdrv_v4l2.h | 33 +
> drivers/mfd/Kconfig | 21 +
> drivers/mfd/Makefile | 1 +
> drivers/mfd/twl-core.c | 8 +
> drivers/mfd/twl4030-madc.c | 537 +++++++
> drivers/misc/ti-st/st_core.c | 355 ++---
> drivers/misc/ti-st/st_kim.c | 56 +-
> drivers/mmc/card/block.c | 4 +-
> drivers/mtd/nand/nand_ecc.c | 2 +-
> drivers/net/smsc911x.c | 4 +-
> drivers/net/wireless/wl12xx/Kconfig | 10 +
> drivers/net/wireless/wl12xx/wl1271.h | 11 +-
> drivers/net/wireless/wl12xx/wl1271_acx.c | 83 +
> drivers/net/wireless/wl12xx/wl1271_acx.h | 86 +
> drivers/net/wireless/wl12xx/wl1271_main.c | 161 ++-
> drivers/net/wireless/wl12xx/wl1271_rx.c | 6 +
> drivers/net/wireless/wl12xx/wl1271_tx.c | 11 +
> drivers/rtc/rtc-twl.c | 25 +
> drivers/serial/omap-serial.c | 4 +
> drivers/video/modedb.c | 4 +
> drivers/video/omap2/displays/Kconfig | 12 +
> drivers/video/omap2/displays/Makefile | 2 +
> .../omap2/displays/panel-lgphilips-lb035q02.c | 244 +++
> .../omap2/displays/panel-samsung-lte430wq-f0c.c | 154 ++
> drivers/video/omap2/dss/dispc.c | 4 +-
> drivers/video/omap2/dss/dpi.c | 7 +-
> drivers/video/omap2/dss/venc.c | 22 +
> drivers/video/omap2/omapfb/omapfb-main.c | 10 +-
> fs/buffer.c | 3 +-
> include/linux/i2c/twl.h | 1 +
> include/linux/i2c/twl4030-madc.h | 130 ++
> include/linux/opp.h | 8 +
> include/linux/ti_wilink_st.h | 40 +-
> include/linux/usb/ehci_def.h | 6 +-
> sound/soc/codecs/twl4030.c | 4 +-
> sound/soc/omap/omap-mcbsp.c | 3 +
> 73 files changed, 7958 insertions(+), 406 deletions(-)
> create mode 100644 drivers/bluetooth/btwilink.c
> create mode 100644 drivers/media/radio/wl128x/Kconfig
> create mode 100644 drivers/media/radio/wl128x/Makefile
> create mode 100644 drivers/media/radio/wl128x/fmdrv.h
> create mode 100644 drivers/media/radio/wl128x/fmdrv_common.c
> create mode 100644 drivers/media/radio/wl128x/fmdrv_common.h
> create mode 100644 drivers/media/radio/wl128x/fmdrv_rx.c
> create mode 100644 drivers/media/radio/wl128x/fmdrv_rx.h
> create mode 100644 drivers/media/radio/wl128x/fmdrv_tx.c
> create mode 100644 drivers/media/radio/wl128x/fmdrv_tx.h
> create mode 100644 drivers/media/radio/wl128x/fmdrv_v4l2.c
> create mode 100644 drivers/media/radio/wl128x/fmdrv_v4l2.h
> create mode 100644 drivers/mfd/twl4030-madc.c
> create mode 100644 drivers/video/omap2/displays/panel-lgphilips-lb035q02.c
> create mode 100644 drivers/video/omap2/displays/panel-samsung-lte430wq-f0c.c
> create mode 100644 include/linux/i2c/twl4030-madc.h
>
> _______________________________________________
> yocto mailing list
> yocto@yoctoproject.org
> https://lists.yoctoproject.org/listinfo/yocto
--
Darren Hart
Intel Open Source Technology Center
Yocto Project - Linux Kernel
prev parent reply other threads:[~2011-06-21 7:23 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-06-21 7:17 [PULL v2][linux-yocto]beagleboard: sync with meta-ti linux-omap_2.6.37 Darren Hart
2011-06-21 7:23 ` Darren Hart [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4E0046DD.4080101@linux.intel.com \
--to=dvhart@linux.intel.com \
--cc=darren@dvhart.com \
--cc=yocto@yoctoproject.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.