From: Darren Hart <darren@dvhart.com>
To: yocto@yoctoproject.org, bruce.ashfield@windriver.com,
koen@dominion.thruhere.net
Cc: Darren Hart <dvhart@linux.intel.com>
Subject: [PULL v2][linux-yocto]beagleboard: sync with meta-ti linux-omap_2.6.37
Date: Tue, 21 Jun 2011 00:17:04 -0700 [thread overview]
Message-ID: <cover.1308639936.git.dvhart@linux.intel.com> (raw)
From: Darren Hart <dvhart@linux.intel.com>
The following commits have been pulled in from the meta-ti linux-omap_2.6.37
recipe, with the exception of:
USB: ehci: remove structure packing from ehci_def
which hails from mainline and should be applied to yocto/base, while the rest
should be applied to yocto/standard/beagleboard.
Fixes [YOCTO #764]
Fixes [YOCTO #765]
Fixes [YOCTO #767]
This brings linux-yocto in sync with the meta-ti linux-omap_2.6.37 recipe and
significantly improves Beagleboard support in linux-yocto. As there are 70
patches in total, and none of them are new, I have omitted them from the email.
V2: Eliminate the linus/* (3) and media/* (42) patches at Koon's suggestion,
reducing patch count from 115 to 70.
The following changes since commit bd97d3f257387a3659b5c2761b0d5323b65203c7:
Merge branch 'yocto/standard/base' into yocto/standard/beagleboard (2011-06-16 15:54:07 -0400)
are available in the git repository at:
git://git.yoctoproject.org/linux-yocto-2.6.37-contrib dvhart/yocto/standard/beagleboard
http://git.yoctoproject.org/cgit.cgi/linux-yocto-2.6.37-contrib/log/?h=dvhart/yocto/standard/beagleboard
Alexander Holler (1):
arm: omap3: beagle: Ensure msecure is mux'd to be able to set the RTC
Arik Nemtsov (1):
wl12xx: Read MAC address from NVS file on HW startup
Darren Hart (2):
board-omap3beagle: whitespace cleanup
board-omap3beagle: allow for building without wl1271
Eliad Peller (1):
wl1271: set wl->vif only if add_interface succeeded.
Juuso Oikarinen (1):
wl12xx: Unset bssid filter, ssid and bssid from firmware on disassoc
Kevin Hilman (1):
OMAP: CPUfreq: ensure policy is fully initialized
Koen Kooi (10):
omap3: beaglexm: fix DVI reset GPIO
omap3: beaglexm: fix power on of DVI
ARM: OMAP: beagleboard: Add infrastructure to do fixups based on
expansionboard name passed by u-boot
ARM: OMAP: beagleboard: pre-export GPIOs to userspace when using a
Tincantools trainerboard
modedb.c: add proper 720p60 mode
ARM: OMAP: add omap_rev_* macros
omap3: beagleboard: add WIP support for beagleboardtoys WL12xx board
beagleboard: hack in support from xM rev C
omap3: allow 1GHz mpurates
BeagleBoard: Adjust USER button pin for xM
Manjunatha Halli (7):
drivers:media:radio: wl128x: FM Driver common header file
drivers:media:radio: wl128x: FM Driver V4L2 sources
drivers:media:radio: wl128x: FM Driver Common sources
drivers:media:radio: wl128x: FM driver RX sources
drivers:media:radio: wl128x: FM driver TX sources
drivers:media:radio: wl128x: Kconfig & Makefile for wl128x driver
drivers:media:radio: Update Kconfig and Makefile for wl128x FM
driver.
Nishanth Menon (2):
omap3|4: opp: make omapx_opp_init non-static
OMAP3: beagle xm: enable upto 1GHz OPP
Pavan Savoy (2):
drivers:misc:ti-st: change protocol parse logic
Bluetooth: btwilink driver
Peter 'p2' De Schrijver (1):
OMAP: CPUfreq: ensure driver initializes after cpufreq framework and
governors
Rabin Vincent (1):
USB: ehci: remove structure packing from ehci_def
Rajendra Nayak (1):
OMAP3 PM: CPUFreq driver for OMAP3
Robert Nelson (2):
omap: Beagle: detect new xM revision B
xM audio fix from Ashok
Sanjeev Premi (1):
omap3: Add basic support for 720MHz part
Shahar Levi (3):
wl1271: 11n Support, Add Definitions
wl1271: 11n Support, ACX Commands
wl1271: 11n Support, functionality and configuration ability
Silesh C V (1):
OMAP: PM: CPUFREQ: Fix conditional compilation
Steve Sakoman (18):
mmc: don't display single block read console messages
MTD: silence ecc errors on mtdblock0
OMAP: DSS2: enable hsclk in dsi_pll_init for OMAP36XX
drivers: net: smsc911x: return ENODEV if device is not found
drivers: input: touchscreen: ads7846: return ENODEV if device is not
found
ASoC: enable audio capture by default for twl4030
MFD: enable madc clock
MFD: add twl4030 madc driver
ARM: OMAP: Add twl4030 madc support to Overo
ARM: OMAP: Add twl4030 madc support to Beagle
OMAP: DSS2: Add support for Samsung LTE430WQ-F0C panel
OMAP: DSS2: Add support for LG Philips LB035Q02 panel
OMAP: DSS2: add bootarg for selecting svideo or composite for tv
output
ARM: OMAP2: mmc-twl4030: move clock input selection prior to vcc test
RTC: add support for backup battery recharge
ARM: OMAP: automatically set musb mode in platform data based on
CONFIG options
OMAP: DSS2: check for both cpu type and revision, rather than just
revision
OMAP: DSS2: Add DSS2 support for Overo
Thara Gopinath (13):
OMAP3: PM: Adding T2 enabling of smartreflex
OMAP: Introduce a user list for each voltage domain instance in the
voltage driver.
OMAP: Introduce API in the OPP layer to find the opp entry
corresponding to a voltage.
OMAP: Introduce API to register a device with a voltagedomain
OMAP: Introduce device specific set rate and get rate in omap_device
structure
OMAP: Voltage layer changes to support DVFS.
OMAP: Introduce dependent voltage domain support.
OMAP: Introduce device scale
OMAP: Disable smartreflex across DVFS
OMAP3: Introduce custom set rate and get rate APIs for scalable
devices
OMAP3: Update cpufreq driver to use the new set_rate API
OMAP3: Introduce voltage domain info in the hwmod structures.
OMAP3: Add voltage dependency table for VDD1.
Thomas Weber (1):
OMAP: Enable Magic SysRq on serial console ttyOx
arch/arm/mach-omap2/board-omap3beagle.c | 409 +++++-
arch/arm/mach-omap2/board-overo.c | 247 +++-
arch/arm/mach-omap2/clock.h | 14 +-
arch/arm/mach-omap2/clock34xx.c | 2 +
arch/arm/mach-omap2/control.h | 7 +
arch/arm/mach-omap2/hsmmc.c | 14 +-
arch/arm/mach-omap2/id.c | 10 +
arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 3 +
arch/arm/mach-omap2/omap_twl.c | 16 +
arch/arm/mach-omap2/opp3xxx_data.c | 66 +-
arch/arm/mach-omap2/opp4xxx_data.c | 3 +-
arch/arm/mach-omap2/pm.c | 110 ++
arch/arm/mach-omap2/voltage.c | 369 +++++-
arch/arm/plat-omap/clock.c | 2 +-
arch/arm/plat-omap/cpu-omap.c | 38 +-
arch/arm/plat-omap/include/plat/cpu.h | 57 +
arch/arm/plat-omap/include/plat/omap_device.h | 12 +-
arch/arm/plat-omap/include/plat/voltage.h | 20 +
arch/arm/plat-omap/omap_device.c | 139 ++
block/blk-core.c | 7 +-
drivers/base/power/opp.c | 28 +
drivers/bluetooth/Kconfig | 10 +
drivers/bluetooth/Makefile | 1 +
drivers/bluetooth/btwilink.c | 397 +++++
drivers/input/touchscreen/ads7846.c | 13 +-
drivers/media/radio/Kconfig | 3 +
drivers/media/radio/Makefile | 1 +
drivers/media/radio/wl128x/Kconfig | 17 +
drivers/media/radio/wl128x/Makefile | 6 +
drivers/media/radio/wl128x/fmdrv.h | 244 +++
drivers/media/radio/wl128x/fmdrv_common.c | 1677 ++++++++++++++++++++
drivers/media/radio/wl128x/fmdrv_common.h | 402 +++++
drivers/media/radio/wl128x/fmdrv_rx.c | 847 ++++++++++
drivers/media/radio/wl128x/fmdrv_rx.h | 59 +
drivers/media/radio/wl128x/fmdrv_tx.c | 425 +++++
drivers/media/radio/wl128x/fmdrv_tx.h | 37 +
drivers/media/radio/wl128x/fmdrv_v4l2.c | 580 +++++++
drivers/media/radio/wl128x/fmdrv_v4l2.h | 33 +
drivers/mfd/Kconfig | 21 +
drivers/mfd/Makefile | 1 +
drivers/mfd/twl-core.c | 8 +
drivers/mfd/twl4030-madc.c | 537 +++++++
drivers/misc/ti-st/st_core.c | 355 ++---
drivers/misc/ti-st/st_kim.c | 56 +-
drivers/mmc/card/block.c | 4 +-
drivers/mtd/nand/nand_ecc.c | 2 +-
drivers/net/smsc911x.c | 4 +-
drivers/net/wireless/wl12xx/Kconfig | 10 +
drivers/net/wireless/wl12xx/wl1271.h | 11 +-
drivers/net/wireless/wl12xx/wl1271_acx.c | 83 +
drivers/net/wireless/wl12xx/wl1271_acx.h | 86 +
drivers/net/wireless/wl12xx/wl1271_main.c | 161 ++-
drivers/net/wireless/wl12xx/wl1271_rx.c | 6 +
drivers/net/wireless/wl12xx/wl1271_tx.c | 11 +
drivers/rtc/rtc-twl.c | 25 +
drivers/serial/omap-serial.c | 4 +
drivers/video/modedb.c | 4 +
drivers/video/omap2/displays/Kconfig | 12 +
drivers/video/omap2/displays/Makefile | 2 +
.../omap2/displays/panel-lgphilips-lb035q02.c | 244 +++
.../omap2/displays/panel-samsung-lte430wq-f0c.c | 154 ++
drivers/video/omap2/dss/dispc.c | 4 +-
drivers/video/omap2/dss/dpi.c | 7 +-
drivers/video/omap2/dss/venc.c | 22 +
drivers/video/omap2/omapfb/omapfb-main.c | 10 +-
fs/buffer.c | 3 +-
include/linux/i2c/twl.h | 1 +
include/linux/i2c/twl4030-madc.h | 130 ++
include/linux/opp.h | 8 +
include/linux/ti_wilink_st.h | 40 +-
include/linux/usb/ehci_def.h | 6 +-
sound/soc/codecs/twl4030.c | 4 +-
sound/soc/omap/omap-mcbsp.c | 3 +
73 files changed, 7958 insertions(+), 406 deletions(-)
create mode 100644 drivers/bluetooth/btwilink.c
create mode 100644 drivers/media/radio/wl128x/Kconfig
create mode 100644 drivers/media/radio/wl128x/Makefile
create mode 100644 drivers/media/radio/wl128x/fmdrv.h
create mode 100644 drivers/media/radio/wl128x/fmdrv_common.c
create mode 100644 drivers/media/radio/wl128x/fmdrv_common.h
create mode 100644 drivers/media/radio/wl128x/fmdrv_rx.c
create mode 100644 drivers/media/radio/wl128x/fmdrv_rx.h
create mode 100644 drivers/media/radio/wl128x/fmdrv_tx.c
create mode 100644 drivers/media/radio/wl128x/fmdrv_tx.h
create mode 100644 drivers/media/radio/wl128x/fmdrv_v4l2.c
create mode 100644 drivers/media/radio/wl128x/fmdrv_v4l2.h
create mode 100644 drivers/mfd/twl4030-madc.c
create mode 100644 drivers/video/omap2/displays/panel-lgphilips-lb035q02.c
create mode 100644 drivers/video/omap2/displays/panel-samsung-lte430wq-f0c.c
create mode 100644 include/linux/i2c/twl4030-madc.h
next reply other threads:[~2011-06-21 7:17 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-06-21 7:17 Darren Hart [this message]
2011-06-21 7:23 ` [PULL v2][linux-yocto]beagleboard: sync with meta-ti linux-omap_2.6.37 Darren Hart
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=cover.1308639936.git.dvhart@linux.intel.com \
--to=darren@dvhart.com \
--cc=bruce.ashfield@windriver.com \
--cc=dvhart@linux.intel.com \
--cc=koen@dominion.thruhere.net \
--cc=yocto@yoctoproject.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.