* [PATCH 3.2 0/4] ARM: simpad: Add support for GPIO attached hardware
@ 2011-08-08 8:49 ` Jochen Friedrich
0 siblings, 0 replies; 18+ messages in thread
From: Jochen Friedrich @ 2011-08-08 8:49 UTC (permalink / raw)
To: linux-arm-kernel, linux, bryan.wu, kristoffer.ericson
Cc: linux-kernel, Jochen Friedrich
This series enables GPIO API on UCB1x00 and implements the GPIO
API on the CS3 latch. The third patch finally registers platform
devices for the GPIO attached LED, buttons and I2C bus.
ARM: simpad: Add ucb1x00 GPIO definitions and register GPIO
ARM: simpad: Cleanup CS3 accessors and add GPIO API
ARM: simpad: add GPIO based device definitions
ARM: simpad: replace ARM specific LED code
Overall diffstat:
arch/arm/mach-sa1100/leds-simpad.c | 100 ------------
b/arch/arm/mach-sa1100/Makefile | 1
b/arch/arm/mach-sa1100/include/mach/simpad.h | 94 +++++++++--
b/arch/arm/mach-sa1100/leds.c | 2
b/arch/arm/mach-sa1100/leds.h | 1
b/arch/arm/mach-sa1100/simpad.c | 213 +++++++++++++++++++++++----
b/drivers/pcmcia/sa1100_simpad.c | 35 ++--
7 files changed, 275 insertions(+), 171 deletions(-)
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 3.2 1/4] ARM: simpad: Add ucb1x00 GPIO definitions and register GPIO
2011-08-08 8:49 ` Jochen Friedrich
@ 2011-08-08 8:49 ` Jochen Friedrich
-1 siblings, 0 replies; 18+ messages in thread
From: Jochen Friedrich @ 2011-08-08 8:49 UTC (permalink / raw)
To: linux-arm-kernel
Add ucb1x00 GPIO definitions to simpad.h and add gpio_base
to ucb1x00 platform device so the pins are available using
the GPIO API.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
---
arch/arm/mach-sa1100/include/mach/simpad.h | 13 +++++++++++++
arch/arm/mach-sa1100/simpad.c | 1 +
2 files changed, 14 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-sa1100/include/mach/simpad.h b/arch/arm/mach-sa1100/include/mach/simpad.h
index 9296c45..231550d 100644
--- a/arch/arm/mach-sa1100/include/mach/simpad.h
+++ b/arch/arm/mach-sa1100/include/mach/simpad.h
@@ -48,6 +48,19 @@
#define GPIO_SMART_CARD GPIO_GPIO10
#define IRQ_GPIO_SMARD_CARD IRQ_GPIO10
+/*--- ucb1x00 GPIO ---*/
+#define SIMPAD_UCB1X00_GPIO_BASE (GPIO_MAX + 1)
+#define SIMPAD_UCB1X00_GPIO_PROG1 (SIMPAD_UCB1X00_GPIO_BASE)
+#define SIMPAD_UCB1X00_GPIO_PROG2 (SIMPAD_UCB1X00_GPIO_BASE + 1)
+#define SIMPAD_UCB1X00_GPIO_UP (SIMPAD_UCB1X00_GPIO_BASE + 2)
+#define SIMPAD_UCB1X00_GPIO_DOWN (SIMPAD_UCB1X00_GPIO_BASE + 3)
+#define SIMPAD_UCB1X00_GPIO_LEFT (SIMPAD_UCB1X00_GPIO_BASE + 4)
+#define SIMPAD_UCB1X00_GPIO_RIGHT (SIMPAD_UCB1X00_GPIO_BASE + 5)
+#define SIMPAD_UCB1X00_GPIO_6 (SIMPAD_UCB1X00_GPIO_BASE + 6)
+#define SIMPAD_UCB1X00_GPIO_7 (SIMPAD_UCB1X00_GPIO_BASE + 7)
+#define SIMPAD_UCB1X00_GPIO_HEADSET (SIMPAD_UCB1X00_GPIO_BASE + 8)
+#define SIMPAD_UCB1X00_GPIO_SPEAKER (SIMPAD_UCB1X00_GPIO_BASE + 9)
+
// CS3 Latch is write only, a shadow is necessary
#define CS3BUSTYPE unsigned volatile long
diff --git a/arch/arm/mach-sa1100/simpad.c b/arch/arm/mach-sa1100/simpad.c
index cfb7607..718b802 100644
--- a/arch/arm/mach-sa1100/simpad.c
+++ b/arch/arm/mach-sa1100/simpad.c
@@ -132,6 +132,7 @@ static struct resource simpad_flash_resources [] = {
static struct mcp_plat_data simpad_mcp_data = {
.mccr0 = MCCR0_ADM,
.sclk_rate = 11981000,
+ .gpio_base = SIMPAD_UCB1X00_GPIO_BASE,
};
--
1.7.5.4
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH 3.2 1/4] ARM: simpad: Add ucb1x00 GPIO definitions and register GPIO
@ 2011-08-08 8:49 ` Jochen Friedrich
0 siblings, 0 replies; 18+ messages in thread
From: Jochen Friedrich @ 2011-08-08 8:49 UTC (permalink / raw)
To: linux-arm-kernel, linux, bryan.wu, kristoffer.ericson
Cc: linux-kernel, Jochen Friedrich
Add ucb1x00 GPIO definitions to simpad.h and add gpio_base
to ucb1x00 platform device so the pins are available using
the GPIO API.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
---
arch/arm/mach-sa1100/include/mach/simpad.h | 13 +++++++++++++
arch/arm/mach-sa1100/simpad.c | 1 +
2 files changed, 14 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-sa1100/include/mach/simpad.h b/arch/arm/mach-sa1100/include/mach/simpad.h
index 9296c45..231550d 100644
--- a/arch/arm/mach-sa1100/include/mach/simpad.h
+++ b/arch/arm/mach-sa1100/include/mach/simpad.h
@@ -48,6 +48,19 @@
#define GPIO_SMART_CARD GPIO_GPIO10
#define IRQ_GPIO_SMARD_CARD IRQ_GPIO10
+/*--- ucb1x00 GPIO ---*/
+#define SIMPAD_UCB1X00_GPIO_BASE (GPIO_MAX + 1)
+#define SIMPAD_UCB1X00_GPIO_PROG1 (SIMPAD_UCB1X00_GPIO_BASE)
+#define SIMPAD_UCB1X00_GPIO_PROG2 (SIMPAD_UCB1X00_GPIO_BASE + 1)
+#define SIMPAD_UCB1X00_GPIO_UP (SIMPAD_UCB1X00_GPIO_BASE + 2)
+#define SIMPAD_UCB1X00_GPIO_DOWN (SIMPAD_UCB1X00_GPIO_BASE + 3)
+#define SIMPAD_UCB1X00_GPIO_LEFT (SIMPAD_UCB1X00_GPIO_BASE + 4)
+#define SIMPAD_UCB1X00_GPIO_RIGHT (SIMPAD_UCB1X00_GPIO_BASE + 5)
+#define SIMPAD_UCB1X00_GPIO_6 (SIMPAD_UCB1X00_GPIO_BASE + 6)
+#define SIMPAD_UCB1X00_GPIO_7 (SIMPAD_UCB1X00_GPIO_BASE + 7)
+#define SIMPAD_UCB1X00_GPIO_HEADSET (SIMPAD_UCB1X00_GPIO_BASE + 8)
+#define SIMPAD_UCB1X00_GPIO_SPEAKER (SIMPAD_UCB1X00_GPIO_BASE + 9)
+
// CS3 Latch is write only, a shadow is necessary
#define CS3BUSTYPE unsigned volatile long
diff --git a/arch/arm/mach-sa1100/simpad.c b/arch/arm/mach-sa1100/simpad.c
index cfb7607..718b802 100644
--- a/arch/arm/mach-sa1100/simpad.c
+++ b/arch/arm/mach-sa1100/simpad.c
@@ -132,6 +132,7 @@ static struct resource simpad_flash_resources [] = {
static struct mcp_plat_data simpad_mcp_data = {
.mccr0 = MCCR0_ADM,
.sclk_rate = 11981000,
+ .gpio_base = SIMPAD_UCB1X00_GPIO_BASE,
};
--
1.7.5.4
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 3.2 2/4] ARM: simpad: Cleanup CS3 accessors.
2011-08-08 8:49 ` Jochen Friedrich
@ 2011-08-08 8:49 ` Jochen Friedrich
-1 siblings, 0 replies; 18+ messages in thread
From: Jochen Friedrich @ 2011-08-08 8:49 UTC (permalink / raw)
To: linux-arm-kernel
- prepend CS3 accessors by simpad_ to indicate they
are specific to simpad devices.
- use spinlock to protect shadow register.
- implement 8 read-only pins.
- use readl/writel macros so barriers are used where
necessary.
- register CS3 as GPIO controller with 24 pins
(16 output only and 8 input only).
- fix PCMCIA driver to access the read-only pins
rather than the shadow register for status bits.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
---
arch/arm/mach-sa1100/include/mach/simpad.h | 81 ++++++++++++++------
arch/arm/mach-sa1100/leds-simpad.c | 7 +-
arch/arm/mach-sa1100/simpad.c | 117 ++++++++++++++++++++++------
drivers/pcmcia/sa1100_simpad.c | 35 ++++-----
4 files changed, 169 insertions(+), 71 deletions(-)
diff --git a/arch/arm/mach-sa1100/include/mach/simpad.h b/arch/arm/mach-sa1100/include/mach/simpad.h
index 231550d..db28118 100644
--- a/arch/arm/mach-sa1100/include/mach/simpad.h
+++ b/arch/arm/mach-sa1100/include/mach/simpad.h
@@ -61,32 +61,67 @@
#define SIMPAD_UCB1X00_GPIO_HEADSET (SIMPAD_UCB1X00_GPIO_BASE + 8)
#define SIMPAD_UCB1X00_GPIO_SPEAKER (SIMPAD_UCB1X00_GPIO_BASE + 9)
-// CS3 Latch is write only, a shadow is necessary
+/*--- CS3 Latch ---*/
+#define SIMPAD_CS3_GPIO_BASE (GPIO_MAX + 11)
+#define SIMPAD_CS3_VCC_5V_EN (SIMPAD_CS3_GPIO_BASE)
+#define SIMPAD_CS3_VCC_3V_EN (SIMPAD_CS3_GPIO_BASE + 1)
+#define SIMPAD_CS3_EN1 (SIMPAD_CS3_GPIO_BASE + 2)
+#define SIMPAD_CS3_EN0 (SIMPAD_CS3_GPIO_BASE + 3)
+#define SIMPAD_CS3_DISPLAY_ON (SIMPAD_CS3_GPIO_BASE + 4)
+#define SIMPAD_CS3_PCMCIA_BUFF_DIS (SIMPAD_CS3_GPIO_BASE + 5)
+#define SIMPAD_CS3_MQ_RESET (SIMPAD_CS3_GPIO_BASE + 6)
+#define SIMPAD_CS3_PCMCIA_RESET (SIMPAD_CS3_GPIO_BASE + 7)
+#define SIMPAD_CS3_DECT_POWER_ON (SIMPAD_CS3_GPIO_BASE + 8)
+#define SIMPAD_CS3_IRDA_SD (SIMPAD_CS3_GPIO_BASE + 9)
+#define SIMPAD_CS3_RS232_ON (SIMPAD_CS3_GPIO_BASE + 10)
+#define SIMPAD_CS3_SD_MEDIAQ (SIMPAD_CS3_GPIO_BASE + 11)
+#define SIMPAD_CS3_LED2_ON (SIMPAD_CS3_GPIO_BASE + 12)
+#define SIMPAD_CS3_IRDA_MODE (SIMPAD_CS3_GPIO_BASE + 13)
+#define SIMPAD_CS3_ENABLE_5V (SIMPAD_CS3_GPIO_BASE + 14)
+#define SIMPAD_CS3_RESET_SIMCARD (SIMPAD_CS3_GPIO_BASE + 15)
+
+#define SIMPAD_CS3_PCMCIA_BVD1 (SIMPAD_CS3_GPIO_BASE + 16)
+#define SIMPAD_CS3_PCMCIA_BVD2 (SIMPAD_CS3_GPIO_BASE + 17)
+#define SIMPAD_CS3_PCMCIA_VS1 (SIMPAD_CS3_GPIO_BASE + 18)
+#define SIMPAD_CS3_PCMCIA_VS2 (SIMPAD_CS3_GPIO_BASE + 19)
+#define SIMPAD_CS3_LOCK_IND (SIMPAD_CS3_GPIO_BASE + 20)
+#define SIMPAD_CS3_CHARGING_STATE (SIMPAD_CS3_GPIO_BASE + 21)
+#define SIMPAD_CS3_PCMCIA_SHORT (SIMPAD_CS3_GPIO_BASE + 22)
+#define SIMPAD_CS3_GPIO_23 (SIMPAD_CS3_GPIO_BASE + 23)
-#define CS3BUSTYPE unsigned volatile long
#define CS3_BASE 0xf1000000
-#define VCC_5V_EN 0x0001 // For 5V PCMCIA
-#define VCC_3V_EN 0x0002 // FOR 3.3V PCMCIA
-#define EN1 0x0004 // This is only for EPROM's
-#define EN0 0x0008 // Both should be enable for 3.3V or 5V
-#define DISPLAY_ON 0x0010
-#define PCMCIA_BUFF_DIS 0x0020
-#define MQ_RESET 0x0040
-#define PCMCIA_RESET 0x0080
-#define DECT_POWER_ON 0x0100
-#define IRDA_SD 0x0200 // Shutdown for powersave
-#define RS232_ON 0x0400
-#define SD_MEDIAQ 0x0800 // Shutdown for powersave
-#define LED2_ON 0x1000
-#define IRDA_MODE 0x2000 // Fast/Slow IrDA mode
-#define ENABLE_5V 0x4000 // Enable 5V circuit
-#define RESET_SIMCARD 0x8000
-
-#define RS232_ENABLE 0x0440
-#define PCMCIAMASK 0x402f
-
-
+long simpad_get_cs3_ro(void);
+long simpad_get_cs3_shadow(void);
+void simpad_set_cs3_bit(int value);
+void simpad_clear_cs3_bit(int value);
+
+#define VCC_5V_EN 0x0001 /* For 5V PCMCIA */
+#define VCC_3V_EN 0x0002 /* FOR 3.3V PCMCIA */
+#define EN1 0x0004 /* This is only for EPROM's */
+#define EN0 0x0008 /* Both should be enable for 3.3V or 5V */
+#define DISPLAY_ON 0x0010
+#define PCMCIA_BUFF_DIS 0x0020
+#define MQ_RESET 0x0040
+#define PCMCIA_RESET 0x0080
+#define DECT_POWER_ON 0x0100
+#define IRDA_SD 0x0200 /* Shutdown for powersave */
+#define RS232_ON 0x0400
+#define SD_MEDIAQ 0x0800 /* Shutdown for powersave */
+#define LED2_ON 0x1000
+#define IRDA_MODE 0x2000 /* Fast/Slow IrDA mode */
+#define ENABLE_5V 0x4000 /* Enable 5V circuit */
+#define RESET_SIMCARD 0x8000
+
+#define PCMCIA_BVD1 0x01
+#define PCMCIA_BVD2 0x02
+#define PCMCIA_VS1 0x04
+#define PCMCIA_VS2 0x08
+#define LOCK_IND 0x10
+#define CHARGING_STATE 0x20
+#define PCMCIA_SHORT 0x40
+
+/*--- Battery ---*/
struct simpad_battery {
unsigned char ac_status; /* line connected yes/no */
unsigned char status; /* battery loading yes/no */
diff --git a/arch/arm/mach-sa1100/leds-simpad.c b/arch/arm/mach-sa1100/leds-simpad.c
index d50f4ee..d25784c 100644
--- a/arch/arm/mach-sa1100/leds-simpad.c
+++ b/arch/arm/mach-sa1100/leds-simpad.c
@@ -22,9 +22,6 @@ static unsigned int hw_led_state;
#define LED_GREEN (1)
#define LED_MASK (1)
-extern void set_cs3_bit(int value);
-extern void clear_cs3_bit(int value);
-
void simpad_leds_event(led_event_t evt)
{
switch (evt)
@@ -93,8 +90,8 @@ void simpad_leds_event(led_event_t evt)
}
if (led_state & LED_STATE_ENABLED)
- set_cs3_bit(LED2_ON);
+ simpad_set_cs3_bit(LED2_ON);
else
- clear_cs3_bit(LED2_ON);
+ simpad_clear_cs3_bit(LED2_ON);
}
diff --git a/arch/arm/mach-sa1100/simpad.c b/arch/arm/mach-sa1100/simpad.c
index 718b802..c3c66b0 100644
--- a/arch/arm/mach-sa1100/simpad.c
+++ b/arch/arm/mach-sa1100/simpad.c
@@ -13,6 +13,7 @@
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/io.h>
+#include <linux/gpio.h>
#include <asm/irq.h>
#include <mach/hardware.h>
@@ -31,32 +32,85 @@
#include "generic.h"
-long cs3_shadow;
+/*
+ * CS3 support
+ */
+
+static long cs3_shadow;
+static spinlock_t cs3_lock;
+static struct gpio_chip cs3_gpio;
+
+long simpad_get_cs3_ro(void)
+{
+ return readl(CS3_BASE);
+}
+EXPORT_SYMBOL(simpad_get_cs3_ro);
-long get_cs3_shadow(void)
+long simpad_get_cs3_shadow(void)
{
return cs3_shadow;
}
+EXPORT_SYMBOL(simpad_get_cs3_shadow);
-void set_cs3(long value)
+static void __simpad_write_cs3(void)
{
- *(CS3BUSTYPE *)(CS3_BASE) = cs3_shadow = value;
+ writel(cs3_shadow, CS3_BASE);
}
-void set_cs3_bit(int value)
+void simpad_set_cs3_bit(int value)
{
+ unsigned long flags;
+
+ spin_lock_irqsave(&cs3_lock, flags);
cs3_shadow |= value;
- *(CS3BUSTYPE *)(CS3_BASE) = cs3_shadow;
+ __simpad_write_cs3();
+ spin_unlock_irqrestore(&cs3_lock, flags);
}
+EXPORT_SYMBOL(simpad_set_cs3_bit);
-void clear_cs3_bit(int value)
+void simpad_clear_cs3_bit(int value)
{
+ unsigned long flags;
+
+ spin_lock_irqsave(&cs3_lock, flags);
cs3_shadow &= ~value;
- *(CS3BUSTYPE *)(CS3_BASE) = cs3_shadow;
+ __simpad_write_cs3();
+ spin_unlock_irqrestore(&cs3_lock, flags);
}
+EXPORT_SYMBOL(simpad_clear_cs3_bit);
+
+static void cs3_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+ if (offset > 15)
+ return;
+ if (value)
+ simpad_set_cs3_bit(1 << offset);
+ else
+ simpad_clear_cs3_bit(1 << offset);
+};
-EXPORT_SYMBOL(set_cs3_bit);
-EXPORT_SYMBOL(clear_cs3_bit);
+static int cs3_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+ if (offset > 15)
+ return simpad_get_cs3_ro() & (1 << (offset - 16));
+ return simpad_get_cs3_shadow() & (1 << offset);
+};
+
+static int cs3_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+ if (offset > 15)
+ return 0;
+ return -EINVAL;
+};
+
+static int cs3_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
+ int value)
+{
+ if (offset > 15)
+ return -EINVAL;
+ cs3_gpio_set(chip, offset, value);
+ return 0;
+};
static struct map_desc simpad_io_desc[] __initdata = {
{ /* MQ200 */
@@ -64,9 +118,9 @@ static struct map_desc simpad_io_desc[] __initdata = {
.pfn = __phys_to_pfn(0x4b800000),
.length = 0x00800000,
.type = MT_DEVICE
- }, { /* Paules CS3, write only */
- .virtual = 0xf1000000,
- .pfn = __phys_to_pfn(0x18000000),
+ }, { /* Simpad CS3 */
+ .virtual = CS3_BASE,
+ .pfn = __phys_to_pfn(SA1100_CS3_PHYS),
.length = 0x00100000,
.type = MT_DEVICE
},
@@ -78,12 +132,12 @@ static void simpad_uart_pm(struct uart_port *port, u_int state, u_int oldstate)
if (port->mapbase == (u_int)&Ser1UTCR0) {
if (state)
{
- clear_cs3_bit(RS232_ON);
- clear_cs3_bit(DECT_POWER_ON);
+ simpad_clear_cs3_bit(RS232_ON);
+ simpad_clear_cs3_bit(DECT_POWER_ON);
}else
{
- set_cs3_bit(RS232_ON);
- set_cs3_bit(DECT_POWER_ON);
+ simpad_set_cs3_bit(RS232_ON);
+ simpad_set_cs3_bit(DECT_POWER_ON);
}
}
}
@@ -143,9 +197,10 @@ static void __init simpad_map_io(void)
iotable_init(simpad_io_desc, ARRAY_SIZE(simpad_io_desc));
- set_cs3_bit (EN1 | EN0 | LED2_ON | DISPLAY_ON | RS232_ON |
- ENABLE_5V | RESET_SIMCARD | DECT_POWER_ON);
-
+ /* Initialize CS3 */
+ cs3_shadow = (EN1 | EN0 | LED2_ON | DISPLAY_ON |
+ RS232_ON | ENABLE_5V | RESET_SIMCARD | DECT_POWER_ON);
+ __simpad_write_cs3(); /* Spinlocks not yet initialized */
sa1100_register_uart_fns(&simpad_port_fns);
sa1100_register_uart(0, 3); /* serial interface */
@@ -171,13 +226,14 @@ static void __init simpad_map_io(void)
static void simpad_power_off(void)
{
- local_irq_disable(); // was cli
- set_cs3(0x800); /* only SD_MEDIAQ */
+ local_irq_disable();
+ cs3_shadow = SD_MEDIAQ;
+ __simpad_write_cs3(); /* Bypass spinlock here */
/* disable internal oscillator, float CS lines */
PCFR = (PCFR_OPDE | PCFR_FP | PCFR_FS);
- /* enable wake-up on GPIO0 (Assabet...) */
- PWER = GFER = GRER = 1;
+ /* enable wake-up on GPIO0 */
+ PWER = GFER = GRER = PWER_GPIO0;
/*
* set scratchpad to zero, just in case it is used as a
* restart address by the bootloader.
@@ -212,6 +268,19 @@ static int __init simpad_init(void)
{
int ret;
+ spin_lock_init(&cs3_lock);
+
+ cs3_gpio.label = "simpad_cs3";
+ cs3_gpio.base = SIMPAD_CS3_GPIO_BASE;
+ cs3_gpio.ngpio = 24;
+ cs3_gpio.set = cs3_gpio_set;
+ cs3_gpio.get = cs3_gpio_get;
+ cs3_gpio.direction_input = cs3_gpio_direction_input;
+ cs3_gpio.direction_output = cs3_gpio_direction_output;
+ ret = gpiochip_add(&cs3_gpio);
+ if (ret)
+ printk(KERN_WARNING "simpad: Unable to register cs3 GPIO device");
+
pm_power_off = simpad_power_off;
sa11x0_register_mtd(&simpad_flash_data, simpad_flash_resources,
diff --git a/drivers/pcmcia/sa1100_simpad.c b/drivers/pcmcia/sa1100_simpad.c
index c998f7a..0fac965 100644
--- a/drivers/pcmcia/sa1100_simpad.c
+++ b/drivers/pcmcia/sa1100_simpad.c
@@ -15,10 +15,6 @@
#include <mach/simpad.h>
#include "sa1100_generic.h"
-extern long get_cs3_shadow(void);
-extern void set_cs3_bit(int value);
-extern void clear_cs3_bit(int value);
-
static struct pcmcia_irqs irqs[] = {
{ 1, IRQ_GPIO_CF_CD, "CF_CD" },
};
@@ -26,7 +22,7 @@ static struct pcmcia_irqs irqs[] = {
static int simpad_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
{
- clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
+ simpad_clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
skt->socket.pci_irq = IRQ_GPIO_CF_IRQ;
@@ -38,8 +34,8 @@ static void simpad_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
soc_pcmcia_free_irqs(skt, irqs, ARRAY_SIZE(irqs));
/* Disable CF bus: */
- //set_cs3_bit(PCMCIA_BUFF_DIS);
- clear_cs3_bit(PCMCIA_RESET);
+ /*simpad_set_cs3_bit(PCMCIA_BUFF_DIS);*/
+ simpad_clear_cs3_bit(PCMCIA_RESET);
}
static void
@@ -47,15 +43,16 @@ simpad_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
struct pcmcia_state *state)
{
unsigned long levels = GPLR;
- long cs3reg = get_cs3_shadow();
+ long cs3reg = simpad_get_cs3_ro();
state->detect=((levels & GPIO_CF_CD)==0)?1:0;
state->ready=(levels & GPIO_CF_IRQ)?1:0;
- state->bvd1=1; /* Not available on Simpad. */
- state->bvd2=1; /* Not available on Simpad. */
+ state->bvd1 = 1; /* Might be cs3reg & PCMCIA_BVD1 */
+ state->bvd2 = 1; /* Might be cs3reg & PCMCIA_BVD2 */
state->wrprot=0; /* Not available on Simpad. */
-
- if((cs3reg & 0x0c) == 0x0c) {
+
+ if ((cs3reg & (PCMCIA_VS1|PCMCIA_VS2)) ==
+ (PCMCIA_VS1|PCMCIA_VS2)) {
state->vs_3v=0;
state->vs_Xv=0;
} else {
@@ -75,23 +72,23 @@ simpad_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
/* Murphy: see table of MIC2562a-1 */
switch (state->Vcc) {
case 0:
- clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
+ simpad_clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
break;
case 33:
- clear_cs3_bit(VCC_3V_EN|EN1);
- set_cs3_bit(VCC_5V_EN|EN0);
+ simpad_clear_cs3_bit(VCC_3V_EN|EN1);
+ simpad_set_cs3_bit(VCC_5V_EN|EN0);
break;
case 50:
- clear_cs3_bit(VCC_5V_EN|EN1);
- set_cs3_bit(VCC_3V_EN|EN0);
+ simpad_clear_cs3_bit(VCC_5V_EN|EN1);
+ simpad_set_cs3_bit(VCC_3V_EN|EN0);
break;
default:
printk(KERN_ERR "%s(): unrecognized Vcc %u\n",
__func__, state->Vcc);
- clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
+ simpad_clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
local_irq_restore(flags);
return -1;
}
@@ -110,7 +107,7 @@ static void simpad_pcmcia_socket_init(struct soc_pcmcia_socket *skt)
static void simpad_pcmcia_socket_suspend(struct soc_pcmcia_socket *skt)
{
soc_pcmcia_disable_irqs(skt, irqs, ARRAY_SIZE(irqs));
- set_cs3_bit(PCMCIA_RESET);
+ simpad_set_cs3_bit(PCMCIA_RESET);
}
static struct pcmcia_low_level simpad_pcmcia_ops = {
--
1.7.5.4
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH 3.2 2/4] ARM: simpad: Cleanup CS3 accessors.
@ 2011-08-08 8:49 ` Jochen Friedrich
0 siblings, 0 replies; 18+ messages in thread
From: Jochen Friedrich @ 2011-08-08 8:49 UTC (permalink / raw)
To: linux-arm-kernel, linux, bryan.wu, kristoffer.ericson
Cc: linux-kernel, Jochen Friedrich
- prepend CS3 accessors by simpad_ to indicate they
are specific to simpad devices.
- use spinlock to protect shadow register.
- implement 8 read-only pins.
- use readl/writel macros so barriers are used where
necessary.
- register CS3 as GPIO controller with 24 pins
(16 output only and 8 input only).
- fix PCMCIA driver to access the read-only pins
rather than the shadow register for status bits.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
---
arch/arm/mach-sa1100/include/mach/simpad.h | 81 ++++++++++++++------
arch/arm/mach-sa1100/leds-simpad.c | 7 +-
arch/arm/mach-sa1100/simpad.c | 117 ++++++++++++++++++++++------
drivers/pcmcia/sa1100_simpad.c | 35 ++++-----
4 files changed, 169 insertions(+), 71 deletions(-)
diff --git a/arch/arm/mach-sa1100/include/mach/simpad.h b/arch/arm/mach-sa1100/include/mach/simpad.h
index 231550d..db28118 100644
--- a/arch/arm/mach-sa1100/include/mach/simpad.h
+++ b/arch/arm/mach-sa1100/include/mach/simpad.h
@@ -61,32 +61,67 @@
#define SIMPAD_UCB1X00_GPIO_HEADSET (SIMPAD_UCB1X00_GPIO_BASE + 8)
#define SIMPAD_UCB1X00_GPIO_SPEAKER (SIMPAD_UCB1X00_GPIO_BASE + 9)
-// CS3 Latch is write only, a shadow is necessary
+/*--- CS3 Latch ---*/
+#define SIMPAD_CS3_GPIO_BASE (GPIO_MAX + 11)
+#define SIMPAD_CS3_VCC_5V_EN (SIMPAD_CS3_GPIO_BASE)
+#define SIMPAD_CS3_VCC_3V_EN (SIMPAD_CS3_GPIO_BASE + 1)
+#define SIMPAD_CS3_EN1 (SIMPAD_CS3_GPIO_BASE + 2)
+#define SIMPAD_CS3_EN0 (SIMPAD_CS3_GPIO_BASE + 3)
+#define SIMPAD_CS3_DISPLAY_ON (SIMPAD_CS3_GPIO_BASE + 4)
+#define SIMPAD_CS3_PCMCIA_BUFF_DIS (SIMPAD_CS3_GPIO_BASE + 5)
+#define SIMPAD_CS3_MQ_RESET (SIMPAD_CS3_GPIO_BASE + 6)
+#define SIMPAD_CS3_PCMCIA_RESET (SIMPAD_CS3_GPIO_BASE + 7)
+#define SIMPAD_CS3_DECT_POWER_ON (SIMPAD_CS3_GPIO_BASE + 8)
+#define SIMPAD_CS3_IRDA_SD (SIMPAD_CS3_GPIO_BASE + 9)
+#define SIMPAD_CS3_RS232_ON (SIMPAD_CS3_GPIO_BASE + 10)
+#define SIMPAD_CS3_SD_MEDIAQ (SIMPAD_CS3_GPIO_BASE + 11)
+#define SIMPAD_CS3_LED2_ON (SIMPAD_CS3_GPIO_BASE + 12)
+#define SIMPAD_CS3_IRDA_MODE (SIMPAD_CS3_GPIO_BASE + 13)
+#define SIMPAD_CS3_ENABLE_5V (SIMPAD_CS3_GPIO_BASE + 14)
+#define SIMPAD_CS3_RESET_SIMCARD (SIMPAD_CS3_GPIO_BASE + 15)
+
+#define SIMPAD_CS3_PCMCIA_BVD1 (SIMPAD_CS3_GPIO_BASE + 16)
+#define SIMPAD_CS3_PCMCIA_BVD2 (SIMPAD_CS3_GPIO_BASE + 17)
+#define SIMPAD_CS3_PCMCIA_VS1 (SIMPAD_CS3_GPIO_BASE + 18)
+#define SIMPAD_CS3_PCMCIA_VS2 (SIMPAD_CS3_GPIO_BASE + 19)
+#define SIMPAD_CS3_LOCK_IND (SIMPAD_CS3_GPIO_BASE + 20)
+#define SIMPAD_CS3_CHARGING_STATE (SIMPAD_CS3_GPIO_BASE + 21)
+#define SIMPAD_CS3_PCMCIA_SHORT (SIMPAD_CS3_GPIO_BASE + 22)
+#define SIMPAD_CS3_GPIO_23 (SIMPAD_CS3_GPIO_BASE + 23)
-#define CS3BUSTYPE unsigned volatile long
#define CS3_BASE 0xf1000000
-#define VCC_5V_EN 0x0001 // For 5V PCMCIA
-#define VCC_3V_EN 0x0002 // FOR 3.3V PCMCIA
-#define EN1 0x0004 // This is only for EPROM's
-#define EN0 0x0008 // Both should be enable for 3.3V or 5V
-#define DISPLAY_ON 0x0010
-#define PCMCIA_BUFF_DIS 0x0020
-#define MQ_RESET 0x0040
-#define PCMCIA_RESET 0x0080
-#define DECT_POWER_ON 0x0100
-#define IRDA_SD 0x0200 // Shutdown for powersave
-#define RS232_ON 0x0400
-#define SD_MEDIAQ 0x0800 // Shutdown for powersave
-#define LED2_ON 0x1000
-#define IRDA_MODE 0x2000 // Fast/Slow IrDA mode
-#define ENABLE_5V 0x4000 // Enable 5V circuit
-#define RESET_SIMCARD 0x8000
-
-#define RS232_ENABLE 0x0440
-#define PCMCIAMASK 0x402f
-
-
+long simpad_get_cs3_ro(void);
+long simpad_get_cs3_shadow(void);
+void simpad_set_cs3_bit(int value);
+void simpad_clear_cs3_bit(int value);
+
+#define VCC_5V_EN 0x0001 /* For 5V PCMCIA */
+#define VCC_3V_EN 0x0002 /* FOR 3.3V PCMCIA */
+#define EN1 0x0004 /* This is only for EPROM's */
+#define EN0 0x0008 /* Both should be enable for 3.3V or 5V */
+#define DISPLAY_ON 0x0010
+#define PCMCIA_BUFF_DIS 0x0020
+#define MQ_RESET 0x0040
+#define PCMCIA_RESET 0x0080
+#define DECT_POWER_ON 0x0100
+#define IRDA_SD 0x0200 /* Shutdown for powersave */
+#define RS232_ON 0x0400
+#define SD_MEDIAQ 0x0800 /* Shutdown for powersave */
+#define LED2_ON 0x1000
+#define IRDA_MODE 0x2000 /* Fast/Slow IrDA mode */
+#define ENABLE_5V 0x4000 /* Enable 5V circuit */
+#define RESET_SIMCARD 0x8000
+
+#define PCMCIA_BVD1 0x01
+#define PCMCIA_BVD2 0x02
+#define PCMCIA_VS1 0x04
+#define PCMCIA_VS2 0x08
+#define LOCK_IND 0x10
+#define CHARGING_STATE 0x20
+#define PCMCIA_SHORT 0x40
+
+/*--- Battery ---*/
struct simpad_battery {
unsigned char ac_status; /* line connected yes/no */
unsigned char status; /* battery loading yes/no */
diff --git a/arch/arm/mach-sa1100/leds-simpad.c b/arch/arm/mach-sa1100/leds-simpad.c
index d50f4ee..d25784c 100644
--- a/arch/arm/mach-sa1100/leds-simpad.c
+++ b/arch/arm/mach-sa1100/leds-simpad.c
@@ -22,9 +22,6 @@ static unsigned int hw_led_state;
#define LED_GREEN (1)
#define LED_MASK (1)
-extern void set_cs3_bit(int value);
-extern void clear_cs3_bit(int value);
-
void simpad_leds_event(led_event_t evt)
{
switch (evt)
@@ -93,8 +90,8 @@ void simpad_leds_event(led_event_t evt)
}
if (led_state & LED_STATE_ENABLED)
- set_cs3_bit(LED2_ON);
+ simpad_set_cs3_bit(LED2_ON);
else
- clear_cs3_bit(LED2_ON);
+ simpad_clear_cs3_bit(LED2_ON);
}
diff --git a/arch/arm/mach-sa1100/simpad.c b/arch/arm/mach-sa1100/simpad.c
index 718b802..c3c66b0 100644
--- a/arch/arm/mach-sa1100/simpad.c
+++ b/arch/arm/mach-sa1100/simpad.c
@@ -13,6 +13,7 @@
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/io.h>
+#include <linux/gpio.h>
#include <asm/irq.h>
#include <mach/hardware.h>
@@ -31,32 +32,85 @@
#include "generic.h"
-long cs3_shadow;
+/*
+ * CS3 support
+ */
+
+static long cs3_shadow;
+static spinlock_t cs3_lock;
+static struct gpio_chip cs3_gpio;
+
+long simpad_get_cs3_ro(void)
+{
+ return readl(CS3_BASE);
+}
+EXPORT_SYMBOL(simpad_get_cs3_ro);
-long get_cs3_shadow(void)
+long simpad_get_cs3_shadow(void)
{
return cs3_shadow;
}
+EXPORT_SYMBOL(simpad_get_cs3_shadow);
-void set_cs3(long value)
+static void __simpad_write_cs3(void)
{
- *(CS3BUSTYPE *)(CS3_BASE) = cs3_shadow = value;
+ writel(cs3_shadow, CS3_BASE);
}
-void set_cs3_bit(int value)
+void simpad_set_cs3_bit(int value)
{
+ unsigned long flags;
+
+ spin_lock_irqsave(&cs3_lock, flags);
cs3_shadow |= value;
- *(CS3BUSTYPE *)(CS3_BASE) = cs3_shadow;
+ __simpad_write_cs3();
+ spin_unlock_irqrestore(&cs3_lock, flags);
}
+EXPORT_SYMBOL(simpad_set_cs3_bit);
-void clear_cs3_bit(int value)
+void simpad_clear_cs3_bit(int value)
{
+ unsigned long flags;
+
+ spin_lock_irqsave(&cs3_lock, flags);
cs3_shadow &= ~value;
- *(CS3BUSTYPE *)(CS3_BASE) = cs3_shadow;
+ __simpad_write_cs3();
+ spin_unlock_irqrestore(&cs3_lock, flags);
}
+EXPORT_SYMBOL(simpad_clear_cs3_bit);
+
+static void cs3_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+ if (offset > 15)
+ return;
+ if (value)
+ simpad_set_cs3_bit(1 << offset);
+ else
+ simpad_clear_cs3_bit(1 << offset);
+};
-EXPORT_SYMBOL(set_cs3_bit);
-EXPORT_SYMBOL(clear_cs3_bit);
+static int cs3_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+ if (offset > 15)
+ return simpad_get_cs3_ro() & (1 << (offset - 16));
+ return simpad_get_cs3_shadow() & (1 << offset);
+};
+
+static int cs3_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+ if (offset > 15)
+ return 0;
+ return -EINVAL;
+};
+
+static int cs3_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
+ int value)
+{
+ if (offset > 15)
+ return -EINVAL;
+ cs3_gpio_set(chip, offset, value);
+ return 0;
+};
static struct map_desc simpad_io_desc[] __initdata = {
{ /* MQ200 */
@@ -64,9 +118,9 @@ static struct map_desc simpad_io_desc[] __initdata = {
.pfn = __phys_to_pfn(0x4b800000),
.length = 0x00800000,
.type = MT_DEVICE
- }, { /* Paules CS3, write only */
- .virtual = 0xf1000000,
- .pfn = __phys_to_pfn(0x18000000),
+ }, { /* Simpad CS3 */
+ .virtual = CS3_BASE,
+ .pfn = __phys_to_pfn(SA1100_CS3_PHYS),
.length = 0x00100000,
.type = MT_DEVICE
},
@@ -78,12 +132,12 @@ static void simpad_uart_pm(struct uart_port *port, u_int state, u_int oldstate)
if (port->mapbase == (u_int)&Ser1UTCR0) {
if (state)
{
- clear_cs3_bit(RS232_ON);
- clear_cs3_bit(DECT_POWER_ON);
+ simpad_clear_cs3_bit(RS232_ON);
+ simpad_clear_cs3_bit(DECT_POWER_ON);
}else
{
- set_cs3_bit(RS232_ON);
- set_cs3_bit(DECT_POWER_ON);
+ simpad_set_cs3_bit(RS232_ON);
+ simpad_set_cs3_bit(DECT_POWER_ON);
}
}
}
@@ -143,9 +197,10 @@ static void __init simpad_map_io(void)
iotable_init(simpad_io_desc, ARRAY_SIZE(simpad_io_desc));
- set_cs3_bit (EN1 | EN0 | LED2_ON | DISPLAY_ON | RS232_ON |
- ENABLE_5V | RESET_SIMCARD | DECT_POWER_ON);
-
+ /* Initialize CS3 */
+ cs3_shadow = (EN1 | EN0 | LED2_ON | DISPLAY_ON |
+ RS232_ON | ENABLE_5V | RESET_SIMCARD | DECT_POWER_ON);
+ __simpad_write_cs3(); /* Spinlocks not yet initialized */
sa1100_register_uart_fns(&simpad_port_fns);
sa1100_register_uart(0, 3); /* serial interface */
@@ -171,13 +226,14 @@ static void __init simpad_map_io(void)
static void simpad_power_off(void)
{
- local_irq_disable(); // was cli
- set_cs3(0x800); /* only SD_MEDIAQ */
+ local_irq_disable();
+ cs3_shadow = SD_MEDIAQ;
+ __simpad_write_cs3(); /* Bypass spinlock here */
/* disable internal oscillator, float CS lines */
PCFR = (PCFR_OPDE | PCFR_FP | PCFR_FS);
- /* enable wake-up on GPIO0 (Assabet...) */
- PWER = GFER = GRER = 1;
+ /* enable wake-up on GPIO0 */
+ PWER = GFER = GRER = PWER_GPIO0;
/*
* set scratchpad to zero, just in case it is used as a
* restart address by the bootloader.
@@ -212,6 +268,19 @@ static int __init simpad_init(void)
{
int ret;
+ spin_lock_init(&cs3_lock);
+
+ cs3_gpio.label = "simpad_cs3";
+ cs3_gpio.base = SIMPAD_CS3_GPIO_BASE;
+ cs3_gpio.ngpio = 24;
+ cs3_gpio.set = cs3_gpio_set;
+ cs3_gpio.get = cs3_gpio_get;
+ cs3_gpio.direction_input = cs3_gpio_direction_input;
+ cs3_gpio.direction_output = cs3_gpio_direction_output;
+ ret = gpiochip_add(&cs3_gpio);
+ if (ret)
+ printk(KERN_WARNING "simpad: Unable to register cs3 GPIO device");
+
pm_power_off = simpad_power_off;
sa11x0_register_mtd(&simpad_flash_data, simpad_flash_resources,
diff --git a/drivers/pcmcia/sa1100_simpad.c b/drivers/pcmcia/sa1100_simpad.c
index c998f7a..0fac965 100644
--- a/drivers/pcmcia/sa1100_simpad.c
+++ b/drivers/pcmcia/sa1100_simpad.c
@@ -15,10 +15,6 @@
#include <mach/simpad.h>
#include "sa1100_generic.h"
-extern long get_cs3_shadow(void);
-extern void set_cs3_bit(int value);
-extern void clear_cs3_bit(int value);
-
static struct pcmcia_irqs irqs[] = {
{ 1, IRQ_GPIO_CF_CD, "CF_CD" },
};
@@ -26,7 +22,7 @@ static struct pcmcia_irqs irqs[] = {
static int simpad_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
{
- clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
+ simpad_clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
skt->socket.pci_irq = IRQ_GPIO_CF_IRQ;
@@ -38,8 +34,8 @@ static void simpad_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
soc_pcmcia_free_irqs(skt, irqs, ARRAY_SIZE(irqs));
/* Disable CF bus: */
- //set_cs3_bit(PCMCIA_BUFF_DIS);
- clear_cs3_bit(PCMCIA_RESET);
+ /*simpad_set_cs3_bit(PCMCIA_BUFF_DIS);*/
+ simpad_clear_cs3_bit(PCMCIA_RESET);
}
static void
@@ -47,15 +43,16 @@ simpad_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
struct pcmcia_state *state)
{
unsigned long levels = GPLR;
- long cs3reg = get_cs3_shadow();
+ long cs3reg = simpad_get_cs3_ro();
state->detect=((levels & GPIO_CF_CD)==0)?1:0;
state->ready=(levels & GPIO_CF_IRQ)?1:0;
- state->bvd1=1; /* Not available on Simpad. */
- state->bvd2=1; /* Not available on Simpad. */
+ state->bvd1 = 1; /* Might be cs3reg & PCMCIA_BVD1 */
+ state->bvd2 = 1; /* Might be cs3reg & PCMCIA_BVD2 */
state->wrprot=0; /* Not available on Simpad. */
-
- if((cs3reg & 0x0c) == 0x0c) {
+
+ if ((cs3reg & (PCMCIA_VS1|PCMCIA_VS2)) ==
+ (PCMCIA_VS1|PCMCIA_VS2)) {
state->vs_3v=0;
state->vs_Xv=0;
} else {
@@ -75,23 +72,23 @@ simpad_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
/* Murphy: see table of MIC2562a-1 */
switch (state->Vcc) {
case 0:
- clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
+ simpad_clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
break;
case 33:
- clear_cs3_bit(VCC_3V_EN|EN1);
- set_cs3_bit(VCC_5V_EN|EN0);
+ simpad_clear_cs3_bit(VCC_3V_EN|EN1);
+ simpad_set_cs3_bit(VCC_5V_EN|EN0);
break;
case 50:
- clear_cs3_bit(VCC_5V_EN|EN1);
- set_cs3_bit(VCC_3V_EN|EN0);
+ simpad_clear_cs3_bit(VCC_5V_EN|EN1);
+ simpad_set_cs3_bit(VCC_3V_EN|EN0);
break;
default:
printk(KERN_ERR "%s(): unrecognized Vcc %u\n",
__func__, state->Vcc);
- clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
+ simpad_clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
local_irq_restore(flags);
return -1;
}
@@ -110,7 +107,7 @@ static void simpad_pcmcia_socket_init(struct soc_pcmcia_socket *skt)
static void simpad_pcmcia_socket_suspend(struct soc_pcmcia_socket *skt)
{
soc_pcmcia_disable_irqs(skt, irqs, ARRAY_SIZE(irqs));
- set_cs3_bit(PCMCIA_RESET);
+ simpad_set_cs3_bit(PCMCIA_RESET);
}
static struct pcmcia_low_level simpad_pcmcia_ops = {
--
1.7.5.4
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 3.2 3/4] ARM: simpad: add GPIO based device definitions.
2011-08-08 8:49 ` Jochen Friedrich
@ 2011-08-08 8:49 ` Jochen Friedrich
-1 siblings, 0 replies; 18+ messages in thread
From: Jochen Friedrich @ 2011-08-08 8:49 UTC (permalink / raw)
To: linux-arm-kernel
Register keyboard, polled keyboard and I2C platform
devices based on GPIOs.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
---
arch/arm/mach-sa1100/simpad.c | 67 ++++++++++++++++++++++++++++++++++++++++-
1 files changed, 66 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-sa1100/simpad.c b/arch/arm/mach-sa1100/simpad.c
index c3c66b0..9f0eefd 100644
--- a/arch/arm/mach-sa1100/simpad.c
+++ b/arch/arm/mach-sa1100/simpad.c
@@ -29,6 +29,9 @@
#include <linux/serial_core.h>
#include <linux/ioport.h>
+#include <linux/input.h>
+#include <linux/gpio_keys.h>
+#include <linux/i2c-gpio.h>
#include "generic.h"
@@ -249,6 +252,65 @@ static void simpad_power_off(void)
}
+/*
+ * gpio_keys
+*/
+
+static struct gpio_keys_button simpad_button_table[] = {
+ { KEY_POWER, IRQ_GPIO_POWER_BUTTON, 1, "power button" },
+};
+
+static struct gpio_keys_platform_data simpad_keys_data = {
+ .buttons = simpad_button_table,
+ .nbuttons = ARRAY_SIZE(simpad_button_table),
+};
+
+static struct platform_device simpad_keys = {
+ .name = "gpio-keys",
+ .dev = {
+ .platform_data = &simpad_keys_data,
+ },
+};
+
+static struct gpio_keys_button simpad_polled_button_table[] = {
+ { KEY_PROG1, SIMPAD_UCB1X00_GPIO_PROG1, 1, "prog1 button" },
+ { KEY_PROG2, SIMPAD_UCB1X00_GPIO_PROG2, 1, "prog2 button" },
+ { KEY_UP, SIMPAD_UCB1X00_GPIO_UP, 1, "up button" },
+ { KEY_DOWN, SIMPAD_UCB1X00_GPIO_DOWN, 1, "down button" },
+ { KEY_LEFT, SIMPAD_UCB1X00_GPIO_LEFT, 1, "left button" },
+ { KEY_RIGHT, SIMPAD_UCB1X00_GPIO_RIGHT, 1, "right button" },
+};
+
+static struct gpio_keys_platform_data simpad_polled_keys_data = {
+ .buttons = simpad_polled_button_table,
+ .nbuttons = ARRAY_SIZE(simpad_polled_button_table),
+ .poll_interval = 50,
+};
+
+static struct platform_device simpad_polled_keys = {
+ .name = "gpio-keys-polled",
+ .dev = {
+ .platform_data = &simpad_polled_keys_data,
+ },
+};
+
+/*
+ * i2c
+ */
+static struct i2c_gpio_platform_data simpad_i2c_data = {
+ .sda_pin = GPIO_GPIO21,
+ .scl_pin = GPIO_GPIO25,
+ .udelay = 10,
+ .timeout = HZ,
+};
+
+static struct platform_device simpad_i2c = {
+ .name = "i2c-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &simpad_i2c_data,
+ },
+};
/*
* MediaQ Video Device
@@ -259,7 +321,10 @@ static struct platform_device simpad_mq200fb = {
};
static struct platform_device *devices[] __initdata = {
- &simpad_mq200fb
+ &simpad_keys,
+ &simpad_polled_keys,
+ &simpad_mq200fb,
+ &simpad_i2c,
};
--
1.7.5.4
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH 3.2 3/4] ARM: simpad: add GPIO based device definitions.
@ 2011-08-08 8:49 ` Jochen Friedrich
0 siblings, 0 replies; 18+ messages in thread
From: Jochen Friedrich @ 2011-08-08 8:49 UTC (permalink / raw)
To: linux-arm-kernel, linux, bryan.wu, kristoffer.ericson
Cc: linux-kernel, Jochen Friedrich
Register keyboard, polled keyboard and I2C platform
devices based on GPIOs.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
---
arch/arm/mach-sa1100/simpad.c | 67 ++++++++++++++++++++++++++++++++++++++++-
1 files changed, 66 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-sa1100/simpad.c b/arch/arm/mach-sa1100/simpad.c
index c3c66b0..9f0eefd 100644
--- a/arch/arm/mach-sa1100/simpad.c
+++ b/arch/arm/mach-sa1100/simpad.c
@@ -29,6 +29,9 @@
#include <linux/serial_core.h>
#include <linux/ioport.h>
+#include <linux/input.h>
+#include <linux/gpio_keys.h>
+#include <linux/i2c-gpio.h>
#include "generic.h"
@@ -249,6 +252,65 @@ static void simpad_power_off(void)
}
+/*
+ * gpio_keys
+*/
+
+static struct gpio_keys_button simpad_button_table[] = {
+ { KEY_POWER, IRQ_GPIO_POWER_BUTTON, 1, "power button" },
+};
+
+static struct gpio_keys_platform_data simpad_keys_data = {
+ .buttons = simpad_button_table,
+ .nbuttons = ARRAY_SIZE(simpad_button_table),
+};
+
+static struct platform_device simpad_keys = {
+ .name = "gpio-keys",
+ .dev = {
+ .platform_data = &simpad_keys_data,
+ },
+};
+
+static struct gpio_keys_button simpad_polled_button_table[] = {
+ { KEY_PROG1, SIMPAD_UCB1X00_GPIO_PROG1, 1, "prog1 button" },
+ { KEY_PROG2, SIMPAD_UCB1X00_GPIO_PROG2, 1, "prog2 button" },
+ { KEY_UP, SIMPAD_UCB1X00_GPIO_UP, 1, "up button" },
+ { KEY_DOWN, SIMPAD_UCB1X00_GPIO_DOWN, 1, "down button" },
+ { KEY_LEFT, SIMPAD_UCB1X00_GPIO_LEFT, 1, "left button" },
+ { KEY_RIGHT, SIMPAD_UCB1X00_GPIO_RIGHT, 1, "right button" },
+};
+
+static struct gpio_keys_platform_data simpad_polled_keys_data = {
+ .buttons = simpad_polled_button_table,
+ .nbuttons = ARRAY_SIZE(simpad_polled_button_table),
+ .poll_interval = 50,
+};
+
+static struct platform_device simpad_polled_keys = {
+ .name = "gpio-keys-polled",
+ .dev = {
+ .platform_data = &simpad_polled_keys_data,
+ },
+};
+
+/*
+ * i2c
+ */
+static struct i2c_gpio_platform_data simpad_i2c_data = {
+ .sda_pin = GPIO_GPIO21,
+ .scl_pin = GPIO_GPIO25,
+ .udelay = 10,
+ .timeout = HZ,
+};
+
+static struct platform_device simpad_i2c = {
+ .name = "i2c-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &simpad_i2c_data,
+ },
+};
/*
* MediaQ Video Device
@@ -259,7 +321,10 @@ static struct platform_device simpad_mq200fb = {
};
static struct platform_device *devices[] __initdata = {
- &simpad_mq200fb
+ &simpad_keys,
+ &simpad_polled_keys,
+ &simpad_mq200fb,
+ &simpad_i2c,
};
--
1.7.5.4
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 3.2 4/4] ARM: simpad: replace ARM specific LED code
2011-08-08 8:49 ` Jochen Friedrich
@ 2011-08-08 8:49 ` Jochen Friedrich
-1 siblings, 0 replies; 18+ messages in thread
From: Jochen Friedrich @ 2011-08-08 8:49 UTC (permalink / raw)
To: linux-arm-kernel
Remove the legacy ARM LED code for simpad devices and
register a stadard LED platform device using GPIO line
instead.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
---
arch/arm/mach-sa1100/Makefile | 1 -
arch/arm/mach-sa1100/leds-simpad.c | 97 ------------------------------------
arch/arm/mach-sa1100/leds.c | 2 -
arch/arm/mach-sa1100/leds.h | 1 -
arch/arm/mach-sa1100/simpad.c | 28 ++++++++++
5 files changed, 28 insertions(+), 101 deletions(-)
delete mode 100644 arch/arm/mach-sa1100/leds-simpad.c
diff --git a/arch/arm/mach-sa1100/Makefile b/arch/arm/mach-sa1100/Makefile
index 41252d2..0063178 100644
--- a/arch/arm/mach-sa1100/Makefile
+++ b/arch/arm/mach-sa1100/Makefile
@@ -45,7 +45,6 @@ obj-$(CONFIG_SA1100_PLEB) += pleb.o
obj-$(CONFIG_SA1100_SHANNON) += shannon.o
obj-$(CONFIG_SA1100_SIMPAD) += simpad.o
-led-$(CONFIG_SA1100_SIMPAD) += leds-simpad.o
# LEDs support
obj-$(CONFIG_LEDS) += $(led-y)
diff --git a/arch/arm/mach-sa1100/leds-simpad.c b/arch/arm/mach-sa1100/leds-simpad.c
deleted file mode 100644
index d25784c..0000000
--- a/arch/arm/mach-sa1100/leds-simpad.c
+++ /dev/null
@@ -1,97 +0,0 @@
-/*
- * linux/arch/arm/mach-sa1100/leds-simpad.c
- *
- * Author: Juergen Messerer <juergen.messerer@siemens.ch>
- */
-#include <linux/init.h>
-
-#include <mach/hardware.h>
-#include <asm/leds.h>
-#include <asm/system.h>
-#include <mach/simpad.h>
-
-#include "leds.h"
-
-
-#define LED_STATE_ENABLED 1
-#define LED_STATE_CLAIMED 2
-
-static unsigned int led_state;
-static unsigned int hw_led_state;
-
-#define LED_GREEN (1)
-#define LED_MASK (1)
-
-void simpad_leds_event(led_event_t evt)
-{
- switch (evt)
- {
- case led_start:
- hw_led_state = LED_GREEN;
- led_state = LED_STATE_ENABLED;
- break;
-
- case led_stop:
- led_state &= ~LED_STATE_ENABLED;
- break;
-
- case led_claim:
- led_state |= LED_STATE_CLAIMED;
- hw_led_state = LED_GREEN;
- break;
-
- case led_release:
- led_state &= ~LED_STATE_CLAIMED;
- hw_led_state = LED_GREEN;
- break;
-
-#ifdef CONFIG_LEDS_TIMER
- case led_timer:
- if (!(led_state & LED_STATE_CLAIMED))
- hw_led_state ^= LED_GREEN;
- break;
-#endif
-
-#ifdef CONFIG_LEDS_CPU
- case led_idle_start:
- break;
-
- case led_idle_end:
- break;
-#endif
-
- case led_halted:
- break;
-
- case led_green_on:
- if (led_state & LED_STATE_CLAIMED)
- hw_led_state |= LED_GREEN;
- break;
-
- case led_green_off:
- if (led_state & LED_STATE_CLAIMED)
- hw_led_state &= ~LED_GREEN;
- break;
-
- case led_amber_on:
- break;
-
- case led_amber_off:
- break;
-
- case led_red_on:
- break;
-
- case led_red_off:
- break;
-
- default:
- break;
- }
-
- if (led_state & LED_STATE_ENABLED)
- simpad_set_cs3_bit(LED2_ON);
- else
- simpad_clear_cs3_bit(LED2_ON);
-}
-
diff --git a/arch/arm/mach-sa1100/leds.c b/arch/arm/mach-sa1100/leds.c
index bbfe197..5fe71a0 100644
--- a/arch/arm/mach-sa1100/leds.c
+++ b/arch/arm/mach-sa1100/leds.c
@@ -42,8 +42,6 @@ sa1100_leds_init(void)
leds_event = adsbitsy_leds_event;
if (machine_is_pt_system3())
leds_event = system3_leds_event;
- if (machine_is_simpad())
- leds_event = simpad_leds_event; /* what about machine registry? including led, apm... -zecke */
leds_event(led_start);
return 0;
diff --git a/arch/arm/mach-sa1100/leds.h b/arch/arm/mach-sa1100/leds.h
index 68cc9f7..776b602 100644
--- a/arch/arm/mach-sa1100/leds.h
+++ b/arch/arm/mach-sa1100/leds.h
@@ -11,4 +11,3 @@ extern void pfs168_leds_event(led_event_t evt);
extern void graphicsmaster_leds_event(led_event_t evt);
extern void adsbitsy_leds_event(led_event_t evt);
extern void system3_leds_event(led_event_t evt);
-extern void simpad_leds_event(led_event_t evt);
diff --git a/arch/arm/mach-sa1100/simpad.c b/arch/arm/mach-sa1100/simpad.c
index 9f0eefd..34659f3 100644
--- a/arch/arm/mach-sa1100/simpad.c
+++ b/arch/arm/mach-sa1100/simpad.c
@@ -31,6 +31,7 @@
#include <linux/ioport.h>
#include <linux/input.h>
#include <linux/gpio_keys.h>
+#include <linux/leds.h>
#include <linux/i2c-gpio.h>
#include "generic.h"
@@ -295,6 +296,32 @@ static struct platform_device simpad_polled_keys = {
};
/*
+ * GPIO LEDs
+ */
+
+static struct gpio_led simpad_leds[] = {
+ {
+ .name = "simpad:power",
+ .gpio = SIMPAD_CS3_LED2_ON,
+ .active_low = 0,
+ .default_trigger = "default-on",
+ },
+};
+
+static struct gpio_led_platform_data simpad_led_data = {
+ .num_leds = ARRAY_SIZE(simpad_leds),
+ .leds = simpad_leds,
+};
+
+static struct platform_device simpad_gpio_leds = {
+ .name = "leds-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &simpad_led_data,
+ },
+};
+
+/*
* i2c
*/
static struct i2c_gpio_platform_data simpad_i2c_data = {
@@ -324,6 +351,7 @@ static struct platform_device *devices[] __initdata = {
&simpad_keys,
&simpad_polled_keys,
&simpad_mq200fb,
+ &simpad_gpio_leds,
&simpad_i2c,
};
--
1.7.5.4
^ permalink raw reply related [flat|nested] 18+ messages in thread* [PATCH 3.2 4/4] ARM: simpad: replace ARM specific LED code
@ 2011-08-08 8:49 ` Jochen Friedrich
0 siblings, 0 replies; 18+ messages in thread
From: Jochen Friedrich @ 2011-08-08 8:49 UTC (permalink / raw)
To: linux-arm-kernel, linux, bryan.wu, kristoffer.ericson
Cc: linux-kernel, Jochen Friedrich
Remove the legacy ARM LED code for simpad devices and
register a stadard LED platform device using GPIO line
instead.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
---
arch/arm/mach-sa1100/Makefile | 1 -
arch/arm/mach-sa1100/leds-simpad.c | 97 ------------------------------------
arch/arm/mach-sa1100/leds.c | 2 -
arch/arm/mach-sa1100/leds.h | 1 -
arch/arm/mach-sa1100/simpad.c | 28 ++++++++++
5 files changed, 28 insertions(+), 101 deletions(-)
delete mode 100644 arch/arm/mach-sa1100/leds-simpad.c
diff --git a/arch/arm/mach-sa1100/Makefile b/arch/arm/mach-sa1100/Makefile
index 41252d2..0063178 100644
--- a/arch/arm/mach-sa1100/Makefile
+++ b/arch/arm/mach-sa1100/Makefile
@@ -45,7 +45,6 @@ obj-$(CONFIG_SA1100_PLEB) += pleb.o
obj-$(CONFIG_SA1100_SHANNON) += shannon.o
obj-$(CONFIG_SA1100_SIMPAD) += simpad.o
-led-$(CONFIG_SA1100_SIMPAD) += leds-simpad.o
# LEDs support
obj-$(CONFIG_LEDS) += $(led-y)
diff --git a/arch/arm/mach-sa1100/leds-simpad.c b/arch/arm/mach-sa1100/leds-simpad.c
deleted file mode 100644
index d25784c..0000000
--- a/arch/arm/mach-sa1100/leds-simpad.c
+++ /dev/null
@@ -1,97 +0,0 @@
-/*
- * linux/arch/arm/mach-sa1100/leds-simpad.c
- *
- * Author: Juergen Messerer <juergen.messerer@siemens.ch>
- */
-#include <linux/init.h>
-
-#include <mach/hardware.h>
-#include <asm/leds.h>
-#include <asm/system.h>
-#include <mach/simpad.h>
-
-#include "leds.h"
-
-
-#define LED_STATE_ENABLED 1
-#define LED_STATE_CLAIMED 2
-
-static unsigned int led_state;
-static unsigned int hw_led_state;
-
-#define LED_GREEN (1)
-#define LED_MASK (1)
-
-void simpad_leds_event(led_event_t evt)
-{
- switch (evt)
- {
- case led_start:
- hw_led_state = LED_GREEN;
- led_state = LED_STATE_ENABLED;
- break;
-
- case led_stop:
- led_state &= ~LED_STATE_ENABLED;
- break;
-
- case led_claim:
- led_state |= LED_STATE_CLAIMED;
- hw_led_state = LED_GREEN;
- break;
-
- case led_release:
- led_state &= ~LED_STATE_CLAIMED;
- hw_led_state = LED_GREEN;
- break;
-
-#ifdef CONFIG_LEDS_TIMER
- case led_timer:
- if (!(led_state & LED_STATE_CLAIMED))
- hw_led_state ^= LED_GREEN;
- break;
-#endif
-
-#ifdef CONFIG_LEDS_CPU
- case led_idle_start:
- break;
-
- case led_idle_end:
- break;
-#endif
-
- case led_halted:
- break;
-
- case led_green_on:
- if (led_state & LED_STATE_CLAIMED)
- hw_led_state |= LED_GREEN;
- break;
-
- case led_green_off:
- if (led_state & LED_STATE_CLAIMED)
- hw_led_state &= ~LED_GREEN;
- break;
-
- case led_amber_on:
- break;
-
- case led_amber_off:
- break;
-
- case led_red_on:
- break;
-
- case led_red_off:
- break;
-
- default:
- break;
- }
-
- if (led_state & LED_STATE_ENABLED)
- simpad_set_cs3_bit(LED2_ON);
- else
- simpad_clear_cs3_bit(LED2_ON);
-}
-
diff --git a/arch/arm/mach-sa1100/leds.c b/arch/arm/mach-sa1100/leds.c
index bbfe197..5fe71a0 100644
--- a/arch/arm/mach-sa1100/leds.c
+++ b/arch/arm/mach-sa1100/leds.c
@@ -42,8 +42,6 @@ sa1100_leds_init(void)
leds_event = adsbitsy_leds_event;
if (machine_is_pt_system3())
leds_event = system3_leds_event;
- if (machine_is_simpad())
- leds_event = simpad_leds_event; /* what about machine registry? including led, apm... -zecke */
leds_event(led_start);
return 0;
diff --git a/arch/arm/mach-sa1100/leds.h b/arch/arm/mach-sa1100/leds.h
index 68cc9f7..776b602 100644
--- a/arch/arm/mach-sa1100/leds.h
+++ b/arch/arm/mach-sa1100/leds.h
@@ -11,4 +11,3 @@ extern void pfs168_leds_event(led_event_t evt);
extern void graphicsmaster_leds_event(led_event_t evt);
extern void adsbitsy_leds_event(led_event_t evt);
extern void system3_leds_event(led_event_t evt);
-extern void simpad_leds_event(led_event_t evt);
diff --git a/arch/arm/mach-sa1100/simpad.c b/arch/arm/mach-sa1100/simpad.c
index 9f0eefd..34659f3 100644
--- a/arch/arm/mach-sa1100/simpad.c
+++ b/arch/arm/mach-sa1100/simpad.c
@@ -31,6 +31,7 @@
#include <linux/ioport.h>
#include <linux/input.h>
#include <linux/gpio_keys.h>
+#include <linux/leds.h>
#include <linux/i2c-gpio.h>
#include "generic.h"
@@ -295,6 +296,32 @@ static struct platform_device simpad_polled_keys = {
};
/*
+ * GPIO LEDs
+ */
+
+static struct gpio_led simpad_leds[] = {
+ {
+ .name = "simpad:power",
+ .gpio = SIMPAD_CS3_LED2_ON,
+ .active_low = 0,
+ .default_trigger = "default-on",
+ },
+};
+
+static struct gpio_led_platform_data simpad_led_data = {
+ .num_leds = ARRAY_SIZE(simpad_leds),
+ .leds = simpad_leds,
+};
+
+static struct platform_device simpad_gpio_leds = {
+ .name = "leds-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &simpad_led_data,
+ },
+};
+
+/*
* i2c
*/
static struct i2c_gpio_platform_data simpad_i2c_data = {
@@ -324,6 +351,7 @@ static struct platform_device *devices[] __initdata = {
&simpad_keys,
&simpad_polled_keys,
&simpad_mq200fb,
+ &simpad_gpio_leds,
&simpad_i2c,
};
--
1.7.5.4
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 3.2 0/4] ARM: simpad: Add support for GPIO attached hardware
2011-08-08 8:49 ` Jochen Friedrich
@ 2011-08-11 15:24 ` Jochen Friedrich
-1 siblings, 0 replies; 18+ messages in thread
From: Jochen Friedrich @ 2011-08-11 15:24 UTC (permalink / raw)
To: linux-arm-kernel
On 08.08.2011 10:49, Jochen Friedrich wrote:
> This series enables GPIO API on UCB1x00 and implements the GPIO
> API on the CS3 latch. The third patch finally registers platform
> devices for the GPIO attached LED, buttons and I2C bus.
>
> ARM: simpad: Add ucb1x00 GPIO definitions and register GPIO
> ARM: simpad: Cleanup CS3 accessors and add GPIO API
> ARM: simpad: add GPIO based device definitions
> ARM: simpad: replace ARM specific LED code
ping.
Did someone have time to look at this yet?
Thanks,
Jochen
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 3.2 0/4] ARM: simpad: Add support for GPIO attached hardware
@ 2011-08-11 15:24 ` Jochen Friedrich
0 siblings, 0 replies; 18+ messages in thread
From: Jochen Friedrich @ 2011-08-11 15:24 UTC (permalink / raw)
To: Jochen Friedrich
Cc: linux-arm-kernel, linux, bryan.wu, kristoffer.ericson,
linux-kernel
On 08.08.2011 10:49, Jochen Friedrich wrote:
> This series enables GPIO API on UCB1x00 and implements the GPIO
> API on the CS3 latch. The third patch finally registers platform
> devices for the GPIO attached LED, buttons and I2C bus.
>
> ARM: simpad: Add ucb1x00 GPIO definitions and register GPIO
> ARM: simpad: Cleanup CS3 accessors and add GPIO API
> ARM: simpad: add GPIO based device definitions
> ARM: simpad: replace ARM specific LED code
ping.
Did someone have time to look at this yet?
Thanks,
Jochen
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 3.2 0/4] ARM: simpad: Add support for GPIO attached hardware
2011-08-11 15:24 ` Jochen Friedrich
@ 2011-08-18 9:05 ` Bryan Wu
-1 siblings, 0 replies; 18+ messages in thread
From: Bryan Wu @ 2011-08-18 9:05 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Aug 11, 2011 at 11:24 PM, Jochen Friedrich <jochen@scram.de> wrote:
> On 08.08.2011 10:49, Jochen Friedrich wrote:
>
>> This series enables GPIO API on UCB1x00 and implements the GPIO
>> API on the CS3 latch. The third patch finally registers platform
>> devices for the GPIO attached LED, buttons and I2C bus.
>>
>> ARM: simpad: Add ucb1x00 GPIO definitions and register GPIO
>> ARM: simpad: Cleanup CS3 accessors and add GPIO API
>> ARM: simpad: add GPIO based device definitions
>> ARM: simpad: replace ARM specific LED code
>
> ping.
>
> Did someone have time to look at this yet?
>
Russell,
Is there any comment, or Jochen can just submit them into patch system
Thanks,
--
Bryan Wu <bryan.wu@canonical.com>
Kernel Developer ? ?+86.138-1617-6545 Mobile
Ubuntu Kernel Team
Canonical Ltd. ? ? ?www.canonical.com
Ubuntu - Linux for human beings | www.ubuntu.com
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 3.2 0/4] ARM: simpad: Add support for GPIO attached hardware
@ 2011-08-18 9:05 ` Bryan Wu
0 siblings, 0 replies; 18+ messages in thread
From: Bryan Wu @ 2011-08-18 9:05 UTC (permalink / raw)
To: Jochen Friedrich, Russell King - ARM Linux
Cc: kristoffer.ericson, linux-kernel, linux-arm-kernel
On Thu, Aug 11, 2011 at 11:24 PM, Jochen Friedrich <jochen@scram.de> wrote:
> On 08.08.2011 10:49, Jochen Friedrich wrote:
>
>> This series enables GPIO API on UCB1x00 and implements the GPIO
>> API on the CS3 latch. The third patch finally registers platform
>> devices for the GPIO attached LED, buttons and I2C bus.
>>
>> ARM: simpad: Add ucb1x00 GPIO definitions and register GPIO
>> ARM: simpad: Cleanup CS3 accessors and add GPIO API
>> ARM: simpad: add GPIO based device definitions
>> ARM: simpad: replace ARM specific LED code
>
> ping.
>
> Did someone have time to look at this yet?
>
Russell,
Is there any comment, or Jochen can just submit them into patch system
Thanks,
--
Bryan Wu <bryan.wu@canonical.com>
Kernel Developer +86.138-1617-6545 Mobile
Ubuntu Kernel Team
Canonical Ltd. www.canonical.com
Ubuntu - Linux for human beings | www.ubuntu.com
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 3.2 0/4] ARM: simpad: Add support for GPIO attached hardware
2011-08-18 9:05 ` Bryan Wu
@ 2011-08-18 10:25 ` Russell King - ARM Linux
-1 siblings, 0 replies; 18+ messages in thread
From: Russell King - ARM Linux @ 2011-08-18 10:25 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Aug 18, 2011 at 05:05:49PM +0800, Bryan Wu wrote:
> On Thu, Aug 11, 2011 at 11:24 PM, Jochen Friedrich <jochen@scram.de> wrote:
> > On 08.08.2011 10:49, Jochen Friedrich wrote:
> >
> >> This series enables GPIO API on UCB1x00 and implements the GPIO
> >> API on the CS3 latch. The third patch finally registers platform
> >> devices for the GPIO attached LED, buttons and I2C bus.
> >>
> >> ARM: simpad: Add ucb1x00 GPIO definitions and register GPIO
> >> ARM: simpad: Cleanup CS3 accessors and add GPIO API
> >> ARM: simpad: add GPIO based device definitions
> >> ARM: simpad: replace ARM specific LED code
> >
> > ping.
> >
> > Did someone have time to look at this yet?
> >
> Russell,
>
> Is there any comment, or Jochen can just submit them into patch system
I don't think so, and yes.
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 3.2 0/4] ARM: simpad: Add support for GPIO attached hardware
@ 2011-08-18 10:25 ` Russell King - ARM Linux
0 siblings, 0 replies; 18+ messages in thread
From: Russell King - ARM Linux @ 2011-08-18 10:25 UTC (permalink / raw)
To: Bryan Wu
Cc: Jochen Friedrich, kristoffer.ericson, linux-kernel,
linux-arm-kernel
On Thu, Aug 18, 2011 at 05:05:49PM +0800, Bryan Wu wrote:
> On Thu, Aug 11, 2011 at 11:24 PM, Jochen Friedrich <jochen@scram.de> wrote:
> > On 08.08.2011 10:49, Jochen Friedrich wrote:
> >
> >> This series enables GPIO API on UCB1x00 and implements the GPIO
> >> API on the CS3 latch. The third patch finally registers platform
> >> devices for the GPIO attached LED, buttons and I2C bus.
> >>
> >> ARM: simpad: Add ucb1x00 GPIO definitions and register GPIO
> >> ARM: simpad: Cleanup CS3 accessors and add GPIO API
> >> ARM: simpad: add GPIO based device definitions
> >> ARM: simpad: replace ARM specific LED code
> >
> > ping.
> >
> > Did someone have time to look at this yet?
> >
> Russell,
>
> Is there any comment, or Jochen can just submit them into patch system
I don't think so, and yes.
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 3.2 0/4] ARM: simpad: Add support for GPIO attached hardware
2011-08-18 10:25 ` Russell King - ARM Linux
@ 2011-08-22 14:50 ` Jochen Friedrich
-1 siblings, 0 replies; 18+ messages in thread
From: Jochen Friedrich @ 2011-08-22 14:50 UTC (permalink / raw)
To: linux-arm-kernel
On 18.08.2011 12:25, Russell King - ARM Linux wrote:
> On Thu, Aug 18, 2011 at 05:05:49PM +0800, Bryan Wu wrote:
>> On Thu, Aug 11, 2011 at 11:24 PM, Jochen Friedrich<jochen@scram.de> wrote:
>>> On 08.08.2011 10:49, Jochen Friedrich wrote:
>>>
>>>> This series enables GPIO API on UCB1x00 and implements the GPIO
>>>> API on the CS3 latch. The third patch finally registers platform
>>>> devices for the GPIO attached LED, buttons and I2C bus.
>>>>
>>>> ARM: simpad: Add ucb1x00 GPIO definitions and register GPIO
>>>> ARM: simpad: Cleanup CS3 accessors and add GPIO API
>>>> ARM: simpad: add GPIO based device definitions
>>>> ARM: simpad: replace ARM specific LED code
>>>
>>> ping.
>>>
>>> Did someone have time to look at this yet?
>>>
>> Russell,
>>
>> Is there any comment, or Jochen can just submit them into patch system
>
> I don't think so, and yes.
Done. 7027/1, 7024/1, 7025/1 and 7026/1.
Thanks,
Jochen
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 3.2 0/4] ARM: simpad: Add support for GPIO attached hardware
@ 2011-08-22 14:50 ` Jochen Friedrich
0 siblings, 0 replies; 18+ messages in thread
From: Jochen Friedrich @ 2011-08-22 14:50 UTC (permalink / raw)
To: Russell King - ARM Linux
Cc: Bryan Wu, kristoffer.ericson, linux-kernel, linux-arm-kernel
On 18.08.2011 12:25, Russell King - ARM Linux wrote:
> On Thu, Aug 18, 2011 at 05:05:49PM +0800, Bryan Wu wrote:
>> On Thu, Aug 11, 2011 at 11:24 PM, Jochen Friedrich<jochen@scram.de> wrote:
>>> On 08.08.2011 10:49, Jochen Friedrich wrote:
>>>
>>>> This series enables GPIO API on UCB1x00 and implements the GPIO
>>>> API on the CS3 latch. The third patch finally registers platform
>>>> devices for the GPIO attached LED, buttons and I2C bus.
>>>>
>>>> ARM: simpad: Add ucb1x00 GPIO definitions and register GPIO
>>>> ARM: simpad: Cleanup CS3 accessors and add GPIO API
>>>> ARM: simpad: add GPIO based device definitions
>>>> ARM: simpad: replace ARM specific LED code
>>>
>>> ping.
>>>
>>> Did someone have time to look at this yet?
>>>
>> Russell,
>>
>> Is there any comment, or Jochen can just submit them into patch system
>
> I don't think so, and yes.
Done. 7027/1, 7024/1, 7025/1 and 7026/1.
Thanks,
Jochen
^ permalink raw reply [flat|nested] 18+ messages in thread