From: Tempura San <tempura.san@gmail.com>
To: Daniel Vetter <daniel@ffwll.ch>
Cc: intel-gfx@lists.freedesktop.org
Subject: Re: i915 module does not find 82865G if configured as secondary
Date: Sun, 09 Oct 2011 13:07:25 +0200 [thread overview]
Message-ID: <4E91806D.8010000@gmail.com> (raw)
In-Reply-To: <20111009101848.GA2947@phenom.ffwll.local>
[-- Attachment #1: Type: text/plain, Size: 2939 bytes --]
Here is the output of lspci -nn:
00:00.0 Host bridge [0600]: Intel Corporation 82865G/PE/P DRAM
Controller/Host-Hub Interface [8086:2570] (rev 02)
00:02.0 Display controller [0380]: Intel Corporation 82865G Integrated
Graphics Controller [8086:2572] (rev 02)
00:06.0 System peripheral [0880]: Intel Corporation 82865G/PE/P
Processor to I/O Memory Interface [8086:2576] (rev 02)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R)
USB UHCI Controller #1 [8086:24d2] (rev 02)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R)
USB UHCI Controller #2 [8086:24d4] (rev 02)
00:1d.2 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R)
USB UHCI Controller #3 [8086:24d7] (rev 02)
00:1d.3 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R)
USB UHCI Controller #4 [8086:24de] (rev 02)
00:1d.7 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R)
USB2 EHCI Controller [8086:24dd] (rev 02)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge
[8086:244e] (rev c2)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC
Interface Bridge [8086:24d0] (rev 02)
00:1f.2 IDE interface [0101]: Intel Corporation 82801EB (ICH5) SATA
Controller [8086:24d1] (rev 02)
00:1f.3 SMBus [0c05]: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus
Controller [8086:24d3] (rev 02)
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801EB/ER
(ICH5/ICH5R) AC'97 Audio Controller [8086:24d5] (rev 02)
03:08.0 Ethernet controller [0200]: Intel Corporation 82562EZ 10/100
Ethernet Controller [8086:1050] (rev 02)
03:0a.0 VGA compatible controller [0300]: Avance Logic Inc. ALG-2302
[4005:2302]
03:0c.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller [1106:3038] (rev 50)
03:0c.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller [1106:3038] (rev 50)
03:0c.2 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0
[1106:3104] (rev 51)
A (bit cleaned - drives, peripherals) dmesg is attached.
rmmod/modprobe does not show any errors - neither on STDERR, nor in syslog:
Only on rmmod the following line is added to dmesg:
# rmmod i915
[...] [drm] Module unloaded
# modprobe -v i915
insmod /lib/modules/2.6.32-5-686/kernel/drivers/gpu/drm/i915/i915.ko
modeset=1
Tempura.
On Sun, 9 Oct 2011 12:38:56 +0200, Daniel Vetter wrote:
> On Sun, Oct 09, 2011 at 11:34:57AM +0200, Tempura San wrote:
>> According to sysfs, agpgart-intel is only bound to the device:
>> 00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM
>> Controller/Host-Hub Interface (rev 02)
> That's actually how it should be.
>
>> In case the BIOS did not do the setup right, is there any way to
>> (re-)initialise it in a running system?
> I'm not sure what's going wrong. Can you attach full dmesg and lspci -nn?
> Also, what error-code does modprobe return when you try to manually
> (re-)load the i915 module?
> -Daniel
[-- Attachment #2: dmesg.txt --]
[-- Type: text/plain, Size: 36047 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-5-686 (Debian 2.6.32-35squeeze2) (dannf@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Fri Sep 9 20:51:05 UTC 2011
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003df70000 (usable)
[ 0.000000] BIOS-e820: 000000003df70000 - 000000003df7a000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003df7a000 - 000000003df80000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003df80000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved)
[ 0.000000] DMI present.
[ 0.000000] last_pfn = 0x3df70 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-C7FFF write-protect
[ 0.000000] C8000-E3FFF uncachable
[ 0.000000] E4000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask FC0000000 write-back
[ 0.000000] 1 base 03DF80000 mask FFFF80000 uncachable
[ 0.000000] 2 base 03E000000 mask FFE000000 uncachable
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 01800000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000373fe000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 0037000000 page 2M
[ 0.000000] 0037000000 - 00373fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 373fe000 @ 7000-d000
[ 0.000000] RAMDISK: 2de02000 - 2e7d3204
[ 0.000000] ACPI: RSDP 000f64a0 00014 (v00 PTLTD )
[ 0.000000] ACPI: RSDT 3df7509c 00038 (v01 PTLTD RSDT 060400D0 LTP 00000000)
[ 0.000000] ACPI: FACP 3df79e93 00074 (v01 IBM THINKCEN 060400D0 PTL 00000001)
[ 0.000000] ACPI: DSDT 3df750d4 04DBF (v01 IBM THINKCEN 060400D0 MSFT 0100000E)
[ 0.000000] ACPI: FACS 3df7afc0 00040
[ 0.000000] ACPI: TCPA 3df79f07 00032 (v01 IBM THINKCEN 060400D0 PTL 00000001)
[ 0.000000] ACPI: APIC 3df79f39 00068 (v01 PTLTD ? APIC 060400D0 LTP 00000000)
[ 0.000000] ACPI: BOOT 3df79fa1 00028 (v01 PTLTD $SBFTBL$ 060400D0 LTP 00000001)
[ 0.000000] ACPI: SSDT 3df79fc9 00037 (v01 PTLTD ACPIHT 060400D0 LTP 00000001)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 107MB HIGHMEM available.
[ 0.000000] 883MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 373fe000
[ 0.000000] low ram: 0 - 373fe000
[ 0.000000] node 0 low ram: 00000000 - 373fe000
[ 0.000000] node 0 bootmap 00009000 - 0000fe80
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 00373fe000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0001000000 - 00014ccbd4] TEXT DATA BSS ==> [0001000000 - 00014ccbd4]
[ 0.000000] #4 [002de02000 - 002e7d3204] RAMDISK ==> [002de02000 - 002e7d3204]
[ 0.000000] #5 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
[ 0.000000] #6 [00014cd000 - 00014d3108] BRK ==> [00014cd000 - 00014d3108]
[ 0.000000] #7 [0000007000 - 0000009000] PGTABLE ==> [0000007000 - 0000009000]
[ 0.000000] #8 [0000009000 - 0000010000] BOOTMAP ==> [0000009000 - 0000010000]
[ 0.000000] found SMP MP-table at [c00f63f0] f63f0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000373fe
[ 0.000000] HighMem 0x000373fe -> 0x0003df70
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0003df70
[ 0.000000] On node 0 totalpages: 253711
[ 0.000000] free_area_init_node: node 0, pgdat c13b4860, node_mem_map c14d5000
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3967 pages, LIFO batch:0
[ 0.000000] Normal zone: 1736 pages used for memmap
[ 0.000000] Normal zone: 220470 pages, LIFO batch:31
[ 0.000000] HighMem zone: 215 pages used for memmap
[ 0.000000] HighMem zone: 27291 pages, LIFO batch:7
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 40000000:bec00000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @c2000000 s34328 r0 d23016 u2097152
[ 0.000000] pcpu-alloc: s34328 r0 d23016 u2097152 alloc=1*4194304
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 251728
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-2.6.32-5-686 root=UUID=a13b579f-2af9-418f-bf25-63e7ca8ffe07 ro
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (000373fe:0003df70)
[ 0.000000] Memory: 990472k/1015232k available (2503k kernel code, 23896k reserved, 1329k data, 380k init, 110024k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd56000 - 0xfffff000 (2724 kB)
[ 0.000000] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.000000] vmalloc : 0xf7bfe000 - 0xff3fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf73fe000 ( 883 MB)
[ 0.000000] .init : 0xc13bf000 - 0xc141e000 ( 380 kB)
[ 0.000000] .data : 0xc1271d79 - 0xc13be480 (1329 kB)
[ 0.000000] .text : 0xc1000000 - 0xc1271d79 (2503 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:1280
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2992.394 MHz processor.
[ 0.004005] Calibrating delay loop (skipped), value calculated using timer frequency.. 5984.78 BogoMIPS (lpj=11969576)
[ 0.004140] Security Framework initialized
[ 0.004203] SELinux: Disabled at boot.
[ 0.004266] Mount-cache hash table entries: 512
[ 0.004474] Initializing cgroup subsys ns
[ 0.004536] Initializing cgroup subsys cpuacct
[ 0.004597] Initializing cgroup subsys devices
[ 0.004657] Initializing cgroup subsys freezer
[ 0.004716] Initializing cgroup subsys net_cls
[ 0.004800] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 0.004898] CPU: L2 cache: 512K
[ 0.004954] CPU: Physical Processor ID: 0
[ 0.005011] CPU: Processor Core ID: 0
[ 0.005070] mce: CPU supports 4 MCE banks
[ 0.005131] Disabling lock debugging due to kernel taint
[ 0.005200] CPU0: Thermal monitoring enabled (TM1)
[ 0.005269] Performance Events: no PMU driver, software events only.
[ 0.005374] Checking 'hlt' instruction... OK.
[ 0.021276] ACPI: Core revision 20090903
[ 0.028312] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.028727] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.068830] CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
[ 0.072001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.008000] Initializing CPU#1
[ 0.008000] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 0.008000] CPU: L2 cache: 512K
[ 0.008000] CPU: Physical Processor ID: 0
[ 0.008000] CPU: Processor Core ID: 0
[ 0.008000] CPU1: Thermal monitoring handled by SMI
[ 0.156133] CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
[ 0.156556] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.160126] Brought up 2 CPUs
[ 0.160186] Total of 2 processors activated (11970.18 BogoMIPS).
[ 0.160603] CPU0 attaching sched-domain:
[ 0.160608] domain 0: span 0-1 level SIBLING
[ 0.160612] groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
[ 0.160620] domain 1: span 0-1 level MC
[ 0.160624] groups: 0-1 (cpu_power = 1178)
[ 0.160630] CPU1 attaching sched-domain:
[ 0.160633] domain 0: span 0-1 level SIBLING
[ 0.160636] groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
[ 0.160642] domain 1: span 0-1 level MC
[ 0.160645] groups: 0-1 (cpu_power = 1178)
[ 0.160760] devtmpfs: initialized
[ 0.160760] regulator: core version 0.5
[ 0.160760] NET: Registered protocol family 16
[ 0.160760] ACPI: bus type pci registered
[ 0.160810] PCI: PCI BIOS revision 2.10 entry at 0xfd98d, last bus=3
[ 0.160872] PCI: Using configuration type 1 for base access
[ 0.161314] bio: create slab <bio-0> at 0
[ 0.164512] ACPI: EC: Look up EC in DSDT
[ 0.182044] ACPI: Interpreter enabled
[ 0.182108] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.182380] ACPI: Using IOAPIC for interrupt routing
[ 0.209213] ACPI: No dock devices found.
[ 0.210559] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.210662] pci 0000:00:00.0: Enabling MCH 'Overflow' Device
[ 0.210732] pci 0000:00:00.0: reg 10 32bit mmio pref: [0xe0000000-0xefffffff]
[ 0.210797] pci 0000:00:02.0: reg 10 32bit mmio pref: [0xd8000000-0xdfffffff]
[ 0.210804] pci 0000:00:02.0: reg 14 32bit mmio: [0xd0080000-0xd00fffff]
[ 0.210810] pci 0000:00:02.0: reg 18 io port: [0x1890-0x1897]
[ 0.210858] pci 0000:00:06.0: reg 10 32bit mmio: [0xfecf0000-0xfecf0fff]
[ 0.210948] pci 0000:00:1d.0: reg 20 io port: [0x1800-0x181f]
[ 0.211001] pci 0000:00:1d.1: reg 20 io port: [0x1820-0x183f]
[ 0.211054] pci 0000:00:1d.2: reg 20 io port: [0x1840-0x185f]
[ 0.211107] pci 0000:00:1d.3: reg 20 io port: [0x1860-0x187f]
[ 0.211168] pci 0000:00:1d.7: reg 10 32bit mmio: [0xd0000000-0xd00003ff]
[ 0.211226] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.211291] pci 0000:00:1d.7: PME# disabled
[ 0.211435] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 0.211443] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
[ 0.211522] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH4 GPIO
[ 0.212028] pci 0000:00:1f.2: reg 10 io port: [0x00-0x07]
[ 0.212035] pci 0000:00:1f.2: reg 14 io port: [0x00-0x03]
[ 0.212041] pci 0000:00:1f.2: reg 18 io port: [0x00-0x07]
[ 0.212048] pci 0000:00:1f.2: reg 1c io port: [0x00-0x03]
[ 0.212055] pci 0000:00:1f.2: reg 20 io port: [0x1880-0x188f]
[ 0.212107] pci 0000:00:1f.3: reg 20 io port: [0x18a0-0x18bf]
[ 0.212150] pci 0000:00:1f.5: reg 10 io port: [0x1c00-0x1cff]
[ 0.212157] pci 0000:00:1f.5: reg 14 io port: [0x18c0-0x18ff]
[ 0.212164] pci 0000:00:1f.5: reg 18 32bit mmio: [0xd0000800-0xd00009ff]
[ 0.212172] pci 0000:00:1f.5: reg 1c 32bit mmio: [0xd0000400-0xd00004ff]
[ 0.212201] pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold
[ 0.212265] pci 0000:00:1f.5: PME# disabled
[ 0.212370] pci 0000:03:08.0: reg 10 32bit mmio: [0xd0100000-0xd0100fff]
[ 0.212378] pci 0000:03:08.0: reg 14 io port: [0x2000-0x203f]
[ 0.212414] pci 0000:03:08.0: supports D1 D2
[ 0.212417] pci 0000:03:08.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.212482] pci 0000:03:08.0: PME# disabled
[ 0.212568] pci 0000:03:0a.0: reg 10 32bit mmio: [0xd0200000-0xd03fffff]
[ 0.212605] pci 0000:03:0a.0: reg 30 32bit mmio pref: [0x000000-0x007fff]
[ 0.212665] pci 0000:03:0c.0: reg 20 io port: [0x2040-0x205f]
[ 0.212691] pci 0000:03:0c.0: PME# supported from D0 D3hot D3cold
[ 0.212756] pci 0000:03:0c.0: PME# disabled
[ 0.212860] pci 0000:03:0c.1: reg 20 io port: [0x2060-0x207f]
[ 0.212887] pci 0000:03:0c.1: PME# supported from D0 D3hot D3cold
[ 0.212950] pci 0000:03:0c.1: PME# disabled
[ 0.213036] pci 0000:03:0c.2: reg 10 32bit mmio: [0xd0101000-0xd01010ff]
[ 0.213078] pci 0000:03:0c.2: PME# supported from D0 D3hot D3cold
[ 0.213142] pci 0000:03:0c.2: PME# disabled
[ 0.213237] pci 0000:00:1e.0: transparent bridge
[ 0.213298] pci 0000:00:1e.0: bridge io port: [0x2000-0x2fff]
[ 0.213303] pci 0000:00:1e.0: bridge 32bit mmio: [0xd0100000-0xd03fffff]
[ 0.213315] pci_bus 0000:00: on NUMA node 0
[ 0.213321] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.213459] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SLOT._PRT]
[ 0.292239] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 0.292865] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11 12 14 15)
[ 0.293486] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 0.294106] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[ 0.294730] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 0.295356] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 *9 10 11 12 14 15)
[ 0.295983] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 *9 10 11 12 14 15)
[ 0.297860] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 7 9 10 11 12 14 15)
[ 0.298504] vgaarb: device added: PCI:0000:03:0a.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.298586] vgaarb: loaded
[ 0.298671] PCI: Using ACPI for IRQ routing
[ 0.298671] hpet clockevent registered
[ 0.298671] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.298671] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.298671] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.304026] Switching to clocksource tsc
[ 0.305705] pnp: PnP ACPI init
[ 0.305786] ACPI: bus type pnp registered
[ 0.332870] pnp: PnP ACPI: found 12 devices
[ 0.332932] ACPI: ACPI bus type pnp unregistered
[ 0.332993] PnPBIOS: Disabled by ACPI PNP
[ 0.333073] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 0.333136] system 00:01: ioport range 0x800-0x87f has been reserved
[ 0.333199] system 00:01: ioport range 0x1000-0x107f has been reserved
[ 0.333262] system 00:01: ioport range 0x1100-0x111f has been reserved
[ 0.333325] system 00:01: ioport range 0x1180-0x11bf has been reserved
[ 0.333389] system 00:01: ioport range 0xe000-0xe00f has been reserved
[ 0.333453] system 00:01: ioport range 0xfe00-0xfe00 has been reserved
[ 0.333516] system 00:01: ioport range 0xfe10-0xfe11 has been reserved
[ 0.333582] system 00:01: iomem range 0xfed20000-0xfed8ffff has been reserved
[ 0.333646] system 00:01: iomem range 0xfed90000-0xfed903ff has been reserved
[ 0.368573] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03
[ 0.368638] pci 0000:00:1e.0: IO window: 0x2000-0x2fff
[ 0.368703] pci 0000:00:1e.0: MEM window: 0xd0100000-0xd03fffff
[ 0.368768] pci 0000:00:1e.0: PREFETCH window: 0x40000000-0x400fffff
[ 0.368844] pci 0000:00:1e.0: setting latency timer to 64
[ 0.368850] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.368853] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.368857] pci_bus 0000:03: resource 0 io: [0x2000-0x2fff]
[ 0.368860] pci_bus 0000:03: resource 1 mem: [0xd0100000-0xd03fffff]
[ 0.368864] pci_bus 0000:03: resource 2 pref mem [0x40000000-0x400fffff]
[ 0.368867] pci_bus 0000:03: resource 3 io: [0x00-0xffff]
[ 0.368871] pci_bus 0000:03: resource 4 mem: [0x000000-0xffffffff]
[ 0.368912] NET: Registered protocol family 2
[ 0.369076] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.369557] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.370245] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.370879] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.370946] TCP reno registered
[ 0.371180] NET: Registered protocol family 1
[ 0.371464] pci 0000:03:08.0: Firmware left e100 interrupts enabled; disabling
[ 0.371545] pci 0000:03:0a.0: Boot video device
[ 0.371653] Unpacking initramfs...
[ 0.710374] Freeing initrd memory: 10052k freed
[ 0.720482] Simple Boot Flag at 0x35 set to 0x1
[ 0.720822] audit: initializing netlink socket (disabled)
[ 0.720897] type=2000 audit(1318090498.719:1): initialized
[ 0.723808] highmem bounce pool size: 64 pages
[ 0.723875] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.725695] VFS: Disk quotas dquot_6.5.2
[ 0.725828] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.725975] msgmni has been set to 1740
[ 0.726307] alg: No test for stdrng (krng)
[ 0.726441] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.726519] io scheduler noop registered
[ 0.726576] io scheduler anticipatory registered
[ 0.726634] io scheduler deadline registered
[ 0.726734] io scheduler cfq registered (default)
[ 0.727003] isapnp: Scanning for PnP cards...
[ 1.080810] isapnp: No Plug & Play device found
[ 1.082606] Linux agpgart interface v0.103
[ 1.082764] agpgart-intel 0000:00:00.0: Intel 865 Chipset
[ 1.083011] agpgart-intel 0000:00:00.0: detected 32636K stolen memory
[ 1.089198] agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xd8000000
[ 1.089353] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.089515] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.089971] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.090200] PNP: No PS/2 controller found. Probing ports directly.
[ 1.091969] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.092037] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.092189] mice: PS/2 mouse device common for all mice
[ 1.092293] rtc_cmos 00:04: RTC can wake from S4
[ 1.092398] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 1.092479] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.092554] cpuidle: using governor ladder
[ 1.092612] cpuidle: using governor menu
[ 1.092673] No iBFT detected.
[ 1.093205] TCP cubic registered
[ 1.093404] NET: Registered protocol family 10
[ 1.094499] Mobile IPv6
[ 1.094556] NET: Registered protocol family 17
[ 1.094636] Using IPI No-Shortcut mode
[ 1.094791] PM: Resume from disk failed.
[ 1.094805] registered taskstats version 1
[ 1.095150] rtc_cmos 00:04: setting system clock to 2011-10-08 16:14:59 UTC (1318090499)
[ 1.095289] Initalizing network drop monitor service
[ 1.095378] Freeing unused kernel memory: 380k freed
[ 1.095822] Write protecting the kernel text: 2504k
[ 1.095912] Write protecting the kernel read-only data: 924k
[ 1.129077] udev[59]: starting version 164
[ 1.340238] usbcore: registered new interface driver usbfs
[ 1.340342] usbcore: registered new interface driver hub
[ 1.341216] usbcore: registered new device driver usb
[ 1.362251] SCSI subsystem initialized
[ 1.368955] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 1.369028] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.369174] e100 0000:03:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 1.373978] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.374098] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 1.374187] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.374201] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.374520] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 1.374644] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.378604] ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
[ 1.378631] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd0000000
[ 1.392861] e100 0000:03:08.0: PME# disabled
[ 1.394171] e100: eth0: e100_probe: addr 0xd0100000, irq 20, MAC addr 00:0d:60:ac:18:9d
[ 1.416929] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.416949] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.417046] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.417056] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.417063] usb usb1: Product: EHCI Host Controller
[ 1.417067] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd
[ 1.417075] usb usb1: SerialNumber: 0000:00:1d.7
[ 1.417493] usb usb1: configuration #1 chosen from 1 choice
[ 1.418089] hub 1-0:1.0: USB hub found
[ 1.418168] hub 1-0:1.0: 8 ports detected
[ 1.418420] ehci_hcd 0000:03:0c.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[ 1.418508] ehci_hcd 0000:03:0c.2: EHCI Host Controller
[ 1.418590] ehci_hcd 0000:03:0c.2: new USB bus registered, assigned bus number 2
[ 1.418732] ehci_hcd 0000:03:0c.2: irq 22, io mem 0xd0101000
[ 1.418837] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.418910] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.418915] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.418988] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
[ 1.419097] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001800
[ 1.419217] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.419283] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.419360] usb usb3: Product: UHCI Host Controller
[ 1.419421] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.419484] usb usb3: SerialNumber: 0000:00:1d.0
[ 1.419803] usb usb3: configuration #1 chosen from 1 choice
[ 1.419980] hub 3-0:1.0: USB hub found
[ 1.420080] hub 3-0:1.0: 2 ports detected
[ 1.420237] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.420310] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.420316] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.420396] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
[ 1.420508] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820
[ 1.420621] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.420686] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.420766] usb usb4: Product: UHCI Host Controller
[ 1.420829] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.420891] usb usb4: SerialNumber: 0000:00:1d.1
[ 1.421852] usb usb4: configuration #1 chosen from 1 choice
[ 1.422573] thermal LNXTHERM:01: registered as thermal_zone0
[ 1.423110] ACPI: Thermal Zone [THM0] (57 C)
[ 1.423917] libata version 3.00 loaded.
[ 1.424521] hub 4-0:1.0: USB hub found
[ 1.424605] hub 4-0:1.0: 2 ports detected
[ 1.424782] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.424859] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.424865] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.424941] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
[ 1.425066] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
[ 1.425184] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.425250] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.425328] usb usb5: Product: UHCI Host Controller
[ 1.425389] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.425452] usb usb5: SerialNumber: 0000:00:1d.2
[ 1.425763] usb usb5: configuration #1 chosen from 1 choice
[ 1.425939] hub 5-0:1.0: USB hub found
[ 1.426011] hub 5-0:1.0: 2 ports detected
[ 1.426159] uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.426232] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 1.426238] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 1.426310] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 6
[ 1.426412] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
[ 1.426524] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.426589] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.426670] usb usb6: Product: UHCI Host Controller
[ 1.426733] usb usb6: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.426796] usb usb6: SerialNumber: 0000:00:1d.3
[ 1.427073] usb usb6: configuration #1 chosen from 1 choice
[ 1.427257] hub 6-0:1.0: USB hub found
[ 1.427327] hub 6-0:1.0: 2 ports detected
[ 1.428190] ehci_hcd 0000:03:0c.2: USB 2.0 started, EHCI 0.95
[ 1.429474] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.429543] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.429624] usb usb2: Product: EHCI Host Controller
[ 1.429653] ata_piix 0000:00:1f.2: version 2.13
[ 1.429688] ata_piix 0000:00:1f.2: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.429697] ata_piix 0000:00:1f.2: MAP [ IDE IDE P0 P1 ]
[ 1.429826] usb usb2: Manufacturer: Linux 2.6.32-5-686 ehci_hcd
[ 1.429897] usb usb2: SerialNumber: 0000:03:0c.2
[ 1.430741] usb usb2: configuration #1 chosen from 1 choice
[ 1.430967] hub 2-0:1.0: USB hub found
[ 1.431046] hub 2-0:1.0: 4 ports detected
[ 1.431251] uhci_hcd 0000:03:0c.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 1.431332] uhci_hcd 0000:03:0c.0: UHCI Host Controller
[ 1.431410] uhci_hcd 0000:03:0c.0: new USB bus registered, assigned bus number 7
[ 1.431528] uhci_hcd 0000:03:0c.0: irq 20, io base 0x00002040
[ 1.431644] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.431709] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.431789] usb usb7: Product: UHCI Host Controller
[ 1.431854] usb usb7: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.431919] usb usb7: SerialNumber: 0000:03:0c.0
[ 1.432316] usb usb7: configuration #1 chosen from 1 choice
[ 1.432528] hub 7-0:1.0: USB hub found
[ 1.432604] hub 7-0:1.0: 2 ports detected
[ 1.432788] uhci_hcd 0000:03:0c.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 1.432864] uhci_hcd 0000:03:0c.1: UHCI Host Controller
[ 1.432943] uhci_hcd 0000:03:0c.1: new USB bus registered, assigned bus number 8
[ 1.433066] uhci_hcd 0000:03:0c.1: irq 21, io base 0x00002060
[ 1.433191] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.433258] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.433339] usb usb8: Product: UHCI Host Controller
[ 1.433400] usb usb8: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.433474] usb usb8: SerialNumber: 0000:03:0c.1
[ 1.434143] usb usb8: configuration #1 chosen from 1 choice
[ 1.434376] hub 8-0:1.0: USB hub found
[ 1.434459] hub 8-0:1.0: 2 ports detected
[ 1.584034] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 1.584138] scsi0 : ata_piix
[ 1.584363] scsi1 : ata_piix
...
[ 1.972429] usb 1-5: New USB device found, idVendor=050d, idProduct=0234
[ 1.972493] usb 1-5: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.972685] usb 1-5: configuration #1 chosen from 1 choice
[ 1.972945] hub 1-5:1.0: USB hub found
[ 1.973192] hub 1-5:1.0: 4 ports detected
...
[ 2.129076] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.130081] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 2.130281] sd 1:0:0:0: Attached scsi generic sg2 type 0
[ 2.276028] usb 4-2: new full speed USB device using uhci_hcd and address 2
[ 2.504493] usb 4-2: New USB device found, idVendor=041e, idProduct=4011
[ 2.504560] usb 4-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.504756] usb 4-2: configuration #1 chosen from 1 choice
[ 2.744024] usb 5-2: new low speed USB device using uhci_hcd and address 2
[ 2.825245] device-mapper: uevent: version 1.0.3
[ 2.825580] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 2.876721] kjournald starting. Commit interval 5 seconds
[ 2.876749] EXT3-fs: mounted filesystem with ordered data mode.
...
[ 4.493938] udev[361]: starting version 164
[ 4.714978] usbcore: registered new interface driver hiddev
...
[ 4.792773] usbcore: registered new interface driver usblp
[ 4.802375] Initializing USB Mass Storage driver...
[ 4.802653] scsi2 : SCSI emulation for USB Mass Storage devices
[ 4.802867] usbcore: registered new interface driver usb-storage
[ 4.802876] USB Mass Storage support registered.
[ 4.803798] usb-storage: device found at 2
[ 4.803802] usb-storage: waiting for device to settle before scanning
[ 5.039595] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/PNP0C0C:00/input/input0
[ 5.039688] ACPI: Power Button [PWRB]
[ 5.039865] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 5.039952] ACPI: Power Button [PWRF]
[ 5.265699] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 5.287143] processor LNXCPU:00: registered as cooling_device0
[ 5.289786] processor LNXCPU:01: registered as cooling_device1
[ 5.353072] Linux video capture interface: v2.00
...
[ 5.778628] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 5.778719] ACPI: I/O resource 0000:00:1f.3 [0x18a0-0x18bf] conflicts with ACPI region SMBR [0x18a0-0x18a7]
[ 5.778804] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 5.779580] input: PWC snapshot button as /devices/pci0000:00/0000:00:1d.1/usb4/4-2/input/input3
[ 5.779819] usbcore: registered new interface driver Philips webcam
[ 5.787577] parport_pc 00:0b: reported by Plug and Play ACPI
[ 5.787705] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 5.790499] intel_rng: Firmware space is locked read-only. If you can't or
[ 5.790502] intel_rng: don't want to disable this in firmware setup, and if
[ 5.790504] intel_rng: you are certain that your system has a functional
[ 5.790506] intel_rng: RNG, try using the 'no_fwh_detect' option.
...
[ 6.263215] usbcore: registered new interface driver usbhid
[ 6.263631] usbhid: v2.6:USB HID core driver
[ 6.288511] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 6.785739] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 7.040197] Bluetooth: Core ver 2.15
[ 7.040360] NET: Registered protocol family 31
[ 7.040426] Bluetooth: HCI device and connection manager initialized
[ 7.040497] Bluetooth: HCI socket layer initialized
[ 7.078250] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 7.078408] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 7.083405] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 7.084204] usbcore: registered new interface driver btusb
[ 7.500023] intel8x0_measure_ac97_clock: measured 54809 usecs (2641 samples)
[ 7.500090] intel8x0: clocking to 48000
[ 8.882572] EXT3 FS on sda2, internal journal
[ 9.441805] padlock: VIA PadLock not detected.
[ 9.802937] usb-storage: device scan complete
[ 9.815724] scsi 2:0:0:0: Direct-Access Lexmark USB Mass Storage 200 PQ: 0 ANSI: 0
[ 9.816831] sd 2:0:0:0: Attached scsi generic sg3 type 0
[ 9.875693] sd 2:0:0:0: [sdc] Attached SCSI removable disk
[ 9.951151] loop: module loaded
[ 10.741103] Adding 2008084k swap on /dev/dm-0. Priority:-1 extents:1 across:2008084k
...
[ 14.246160] Bridge firewalling registered
[ 14.253274] device eth0 entered promiscuous mode
[ 14.274053] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 14.277156] e100: eth0 NIC Link is Up 100 Mbps Full Duplex
[ 14.281489] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 14.283269] br0: port 1(eth0) entering learning state
[ 23.280011] br0: port 1(eth0) entering forwarding state
[ 24.556016] eth0: no IPv6 routers present
[ 24.744006] br0: no IPv6 routers present
[ 29.008336] RPC: Registered udp transport module.
[ 29.008419] RPC: Registered tcp transport module.
[ 29.008481] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 29.065002] Slow work thread pool: Starting up
[ 29.065184] Slow work thread pool: Ready
[ 29.065357] FS-Cache: Loaded
[ 29.115283] FS-Cache: Netfs 'nfs' registered for caching
[ 29.139825] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 29.480608] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 29.536642] nf_conntrack version 0.5.0 (15646 buckets, 62584 max)
[ 29.537371] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 29.537456] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 29.537537] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 29.545844] fuse init (API version 7.13)
[ 29.944564] ttyS1: LSR safety check engaged!
[ 29.945896] ttyS1: LSR safety check engaged!
[ 33.928139] ttyS1: LSR safety check engaged!
[ 37.126605] tun: Universal TUN/TAP device driver, 1.6
[ 37.126689] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 37.854737] device tap0 entered promiscuous mode
[ 37.856279] br0: port 2(tap0) entering learning state
[ 41.736101] [drm] Initialized drm 1.1.0 20060810
[ 44.089133] Bluetooth: L2CAP ver 2.14
[ 44.089202] Bluetooth: L2CAP socket layer initialized
[ 44.349936] Bluetooth: RFCOMM TTY layer initialized
[ 44.350010] Bluetooth: RFCOMM socket layer initialized
[ 44.350076] Bluetooth: RFCOMM ver 1.11
[ 44.367196] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 44.367270] Bluetooth: BNEP filters: protocol multicast
[ 44.440508] Bluetooth: SCO (Voice Link) ver 0.6
[ 44.440579] Bluetooth: SCO socket layer initialized
[ 46.857034] br0: port 2(tap0) entering forwarding state
[ 46.873242] lp0: using parport0 (interrupt-driven).
[ 46.904003] ppdev: user-space parallel port driver
[ 48.780010] tap0: no IPv6 routers present
...
[-- Attachment #3: Type: text/plain, Size: 159 bytes --]
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
next prev parent reply other threads:[~2011-10-09 11:08 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-10-08 15:25 i915 module does not find 82865G if configured as secondary Tempura San
2011-10-08 16:33 ` Felix Miata
2011-10-09 9:52 ` Tempura San
2011-10-08 19:37 ` Dave Airlie
2011-10-09 9:34 ` Tempura San
2011-10-09 10:38 ` Daniel Vetter
2011-10-09 11:07 ` Tempura San [this message]
2011-10-09 12:44 ` Daniel Vetter
2011-10-09 18:36 ` Chris Wilson
2011-10-09 20:20 ` Tempura San
2011-10-10 19:06 ` Julien Cristau
2011-10-10 20:32 ` Tempura San
2011-10-10 20:53 ` Chris Wilson
2011-10-11 8:25 ` Dave Airlie
2011-10-15 11:44 ` Tempura San
2011-10-09 20:19 ` Tempura San
2011-10-10 6:55 ` Daniel Vetter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4E91806D.8010000@gmail.com \
--to=tempura.san@gmail.com \
--cc=daniel@ffwll.ch \
--cc=intel-gfx@lists.freedesktop.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.