* Ooops while loading od mceusb staging module
@ 2011-11-19 0:03 TomCat
0 siblings, 0 replies; only message in thread
From: TomCat @ 2011-11-19 0:03 UTC (permalink / raw)
To: linux-kernel; +Cc: jarod
[-- Attachment #1: Type: text/plain, Size: 422 bytes --]
Hi there.
While loading mceusb module I get Ooops
and modprobe gets killed.
This happens on 2 diffrent machines and both 32 and 64 bit kernels.
At first it happened on kernels from ARCH distribution but to see debug
messages with USB debug enabled I tried it on freshly built kernel on
virtualbox with the same result.
Attached are lsusb -v for device which is expected to be driven by
mceusb and dmesg.
Regards
T.
[-- Attachment #2: lsusb --]
[-- Type: text/plain, Size: 4308 bytes --]
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 3.01
iManufacturer 3 Linux 3.1.1 ohci_hcd
iProduct 2 OHCI Host Controller
iSerial 1 0000:00:1f.4
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 11
bDescriptorType 41
nNbrPorts 8
wHubCharacteristic 0x0002
No power switching (usb 1.0)
Ganged overcurrent protection
bPwrOn2PwrGood 0 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00 0x00
PortPwrCtrlMask 0xff 0xff
Hub Port Status:
Port 1: 0000.0103 power enable connect
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Port 7: 0000.0100 power
Port 8: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 001 Device 002: ID 0471:206c Philips (or NXP)
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0471 Philips (or NXP)
idProduct 0x206c
bcdDevice 0.02
iManufacturer 1 PHILIPS
iProduct 2 MCE USB IR Receiver- Spinel plusf0r ASUS
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 1 Keyboard
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 481
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Device Status: 0x0000
(Bus Powered)
[-- Attachment #3: dmesg --]
[-- Type: text/plain, Size: 36812 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.1.1 (tomcat@) (gcc version 4.6.2 (GCC) ) #2 SMP PREEMPT Sat Nov 19 00:01:16 CET 2011
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000dbff0000 (usable)
[ 0.000000] BIOS-e820: 00000000dbff0000 - 00000000dc000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 000000014a300000 (usable)
[ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
[ 0.000000] DMI 2.5 present.
[ 0.000000] DMI: innotek GmbH VirtualBox, BIOS VirtualBox 12/01/2006
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] last_pfn = 0xdbff0 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR variable ranges disabled:
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] CPU MTRRs all blank - virtualized system.
[ 0.000000] found SMP MP-table at [c009fff0] 9fff0
[ 0.000000] initial memory mapped : 0 - 00c00000
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 0037400000 page 2M
[ 0.000000] 0037400000 - 00377fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 377fe000 @ bfb000-c00000
[ 0.000000] RAMDISK: 7fe0e000 - 7fff0000
[ 0.000000] Allocated new RAMDISK: 3761c000 - 377fdb68
[ 0.000000] Move RAMDISK from 000000007fe0e000 - 000000007ffefb67 to 3761c000 - 377fdb67
[ 0.000000] ACPI: RSDP 000e0000 00024 (v02 VBOX )
[ 0.000000] ACPI: XSDT dbff0040 0004C (v01 VBOX VBOXXSDT 00000001 ASL 00000061)
[ 0.000000] ACPI: FACP dbff0110 000F4 (v04 VBOX VBOXFACP 00000001 ASL 00000061)
[ 0.000000] ACPI: DSDT dbff0540 01B96 (v01 VBOX VBOXBIOS 00000002 INTL 20110922)
[ 0.000000] ACPI: FACS dbff0240 00040
[ 0.000000] ACPI: APIC dbff0280 0006C (v02 VBOX VBOXAPIC 00000001 ASL 00000061)
[ 0.000000] ACPI: HPET dbff02f0 00038 (v01 VBOX VBOXHPET 00000001 ASL 00000061)
[ 0.000000] ACPI: MCFG dbff0330 0003C (v01 VBOX VBOXMCFG 00000001 ASL 00000061)
[ 0.000000] ACPI: SSDT dbff0370 001CC (v01 VBOX VBOXCPUT 00000002 INTL 20110922)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 2631MB HIGHMEM available.
[ 0.000000] 887MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 377fe000
[ 0.000000] low ram: 0 - 377fe000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000377fe
[ 0.000000] HighMem 0x000377fe -> 0x000dbff0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x000dbff0
[ 0.000000] On node 0 totalpages: 900991
[ 0.000000] free_area_init_node: node 0, pgdat c05ce5c0, node_mem_map f5a9b200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1744 pages used for memmap
[ 0.000000] Normal zone: 221486 pages, LIFO batch:31
[ 0.000000] HighMem zone: 5264 pages used for memmap
[ 0.000000] HighMem zone: 668514 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at dc000000 (gap: dc000000:23fc0000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 13 pages/cpu @f5400000 s29632 r0 d23616 u1048576
[ 0.000000] pcpu-alloc: s29632 r0 d23616 u1048576 alloc=1*4194304
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 893951
[ 0.000000] Kernel command line: root=/dev/disk/by-uuid/632bc097-2903-46fd-8f69-c1a9795c079c ro
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] allocated 14417408 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Initializing HighMem for node 0 (000377fe:000dbff0)
[ 0.000000] Memory: 3552300k/3604416k available (3473k kernel code, 51664k reserved, 1482k data, 508k init, 2695112k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
[ 0.000000] .init : 0xc05d7000 - 0xc0656000 ( 508 kB)
[ 0.000000] .data : 0xc0464555 - 0xc05d7000 (1482 kB)
[ 0.000000] .text : 0xc0100000 - 0xc0464555 (3473 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:512
[ 0.000000] CPU 0 irqstacks, hard=f400e000 soft=f4020000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 3050.843 MHz processor.
[ 0.006670] Calibrating delay loop (skipped), value calculated using timer frequency.. 6104.92 BogoMIPS (lpj=10169476)
[ 0.007690] pid_max: default: 32768 minimum: 301
[ 0.008200] Security Framework initialized
[ 0.008662] AppArmor: AppArmor disabled by boot time parameter
[ 0.010020] Mount-cache hash table entries: 512
[ 0.011150] Initializing cgroup subsys cpuacct
[ 0.011634] Initializing cgroup subsys memory
[ 0.012107] Initializing cgroup subsys devices
[ 0.012576] Initializing cgroup subsys freezer
[ 0.013339] Initializing cgroup subsys net_cls
[ 0.013810] Initializing cgroup subsys blkio
[ 0.014387] CPU: Physical Processor ID: 0
[ 0.014843] CPU: Processor Core ID: 0
[ 0.015323] mce: CPU supports 0 MCE banks
[ 0.020494] ACPI: Core revision 20110623
[ 0.021610] ftrace: allocating 15589 entries in 31 pages
[ 0.023411] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.027028] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.063512] CPU0: Intel(R) Core(TM) i5-2400 CPU @ 3.10GHz stepping 07
[ 0.066663] APIC calibration not consistent with PM-Timer: 106ms instead of 100ms
[ 0.066663] APIC delta adjusted to PM-Timer: 6250016 (6666587)
[ 0.066663] Performance Events: unsupported p6 CPU model 42 no PMU driver, software events only.
[ 0.083984] NMI watchdog disabled (cpu0): hardware events not enabled
[ 0.110012] CPU 1 irqstacks, hard=f40b2000 soft=f40b4000
[ 0.110014] Booting Node 0, Processors #1
[ 0.110386] smpboot cpu 1: start_ip = 9b000
[ 0.009999] Initializing CPU#1
[ 0.009999] mce: CPU supports 0 MCE banks
[ 0.219986] TSC synchronization [CPU#0 -> CPU#1]:
[ 0.219986] Measured 552426 cycles TSC warp between CPUs, turning off TSC clock.
[ 0.219986] Marking TSC unstable due to check_tsc_sync_source failed
[ 0.220016] NMI watchdog disabled (cpu1): hardware events not enabled
[ 0.240184] CPU 2 irqstacks, hard=f40c0000 soft=f40c2000
[ 0.240187] #2
[ 0.240366] smpboot cpu 2: start_ip = 9b000
[ 0.009999] Initializing CPU#2
[ 0.009999] mce: CPU supports 0 MCE banks
[ 0.333600] NMI watchdog disabled (cpu2): hardware events not enabled
[ 0.353533] CPU 3 irqstacks, hard=f40ce000 soft=f40d0000
[ 0.353536] #3 Ok.
[ 0.353943] smpboot cpu 3: start_ip = 9b000
[ 0.009999] Initializing CPU#3
[ 0.009999] mce: CPU supports 0 MCE banks
[ 0.446714] NMI watchdog disabled (cpu3): hardware events not enabled
[ 0.453323] Brought up 4 CPUs
[ 0.453843] Total of 4 processors activated (24464.47 BogoMIPS).
[ 0.458482] devtmpfs: initialized
[ 0.460521] print_constraints: dummy:
[ 0.461095] NET: Registered protocol family 16
[ 0.461647] ACPI: bus type pci registered
[ 0.462214] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xdc000000-0xdfffffff] (base 0xdc000000)
[ 0.463072] PCI: not using MMCONFIG
[ 0.536817] bios32_service(0x49435024): not present
[ 0.537311] PCI: Using configuration type 1 for base access
[ 0.538403] bio: create slab <bio-0> at 0
[ 0.538403] ACPI: Added _OSI(Module Device)
[ 0.538403] ACPI: Added _OSI(Processor Device)
[ 0.539969] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.540443] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.541234] ACPI: EC: Look up EC in DSDT
[ 0.541468] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.544692] ACPI: Interpreter enabled
[ 0.545136] ACPI: (supports S0 S5)
[ 0.545807] ACPI: Using IOAPIC for interrupt routing
[ 0.546424] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xdc000000-0xdfffffff] (base 0xdc000000)
[ 0.546773] PCI: MMCONFIG at [mem 0xdc000000-0xdfffffff] reserved in ACPI motherboard resources
[ 0.547619] PCI: Using MMCONFIG for extended config space
[ 0.550212] ACPI: No dock devices found.
[ 0.550667] HEST: Table not found.
[ 0.551101] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.551991] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.552595] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.552596] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.552598] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.552600] pci_root PNP0A03:00: host bridge window [mem 0xdc000000-0xffdfffff] (ignored)
[ 0.552643] pci 0000:00:02.0: [80ee:beef] type 0 class 0x000300
[ 0.554588] pci 0000:00:02.0: reg 10: [mem 0xe0000000-0xe3ffffff pref]
[ 0.576778] pci 0000:00:03.0: [1af4:1000] type 0 class 0x000200
[ 0.576897] pci 0000:00:03.0: reg 10: [io 0xd000-0xd01f]
[ 0.577393] pci 0000:00:04.0: [80ee:cafe] type 0 class 0x000880
[ 0.579812] pci 0000:00:04.0: reg 10: [io 0xd020-0xd03f]
[ 0.582582] pci 0000:00:04.0: reg 14: [mem 0xf0000000-0xf03fffff]
[ 0.583539] pci 0000:00:04.0: reg 18: [mem 0xf0400000-0xf0403fff pref]
[ 0.596739] pci 0000:00:05.0: [8086:2415] type 0 class 0x000401
[ 0.596830] pci 0000:00:05.0: reg 10: [io 0xd100-0xd1ff]
[ 0.596890] pci 0000:00:05.0: reg 14: [io 0xd200-0xd23f]
[ 0.597263] pci 0000:00:07.0: [8086:7113] type 0 class 0x000680
[ 0.597834] pci 0000:00:18.0: [8086:2448] type 1 class 0x000604
[ 0.598061] pci 0000:00:19.0: [8086:2448] type 1 class 0x000604
[ 0.598310] pci 0000:00:1f.0: [8086:27b9] type 0 class 0x000601
[ 0.598689] pci 0000:00:1f.0: quirk: [io 0x8000-0x807f] claimed by ICH6 ACPI/GPIO/TCO
[ 0.599663] pci 0000:00:1f.2: [8086:2829] type 0 class 0x000106
[ 0.600246] pci 0000:00:1f.2: reg 10: [io 0xe000-0xe007]
[ 0.603782] pci 0000:00:1f.2: reg 14: [io 0xe008-0xe00b]
[ 0.606931] pci 0000:00:1f.2: reg 18: [io 0xe010-0xe017]
[ 0.610515] pci 0000:00:1f.2: reg 1c: [io 0xe018-0xe01b]
[ 0.613327] pci 0000:00:1f.2: reg 20: [io 0xe020-0xe02f]
[ 0.616121] pci 0000:00:1f.2: reg 24: [mem 0xf0500000-0xf0501fff]
[ 0.620283] pci 0000:00:1f.4: [106b:003f] type 0 class 0x000c03
[ 0.622428] pci 0000:00:1f.4: reg 10: [mem 0xf0502000-0xf0502fff]
[ 0.637334] pci 0000:00:18.0: PCI bridge to [bus 01-ff] (subtractive decode)
[ 0.637950] pci 0000:00:18.0: bridge window [io 0x0000-0xffff] (subtractive decode)
[ 0.637952] pci 0000:00:18.0: bridge window [mem 0x00000000-0xffffffff] (subtractive decode)
[ 0.640242] pci 0000:00:19.0: PCI bridge to [bus 02-ff] (subtractive decode)
[ 0.640841] pci 0000:00:19.0: bridge window [io 0x0000-0xffff] (subtractive decode)
[ 0.640843] pci 0000:00:19.0: bridge window [mem 0x00000000-0xffffffff] (subtractive decode)
[ 0.640860] pci_bus 0000:00: on NUMA node 0
[ 0.640880] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.641480] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.642026] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
[ 0.642842] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.645837] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 9 10 *11)
[ 0.647503] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 *9 10 11)
[ 0.648817] ACPI: PCI Interrupt Link [LNKC] (IRQs 5 9 10 *11)
[ 0.650022] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 *9 10 11)
[ 0.651297] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.651297] vgaarb: loaded
[ 0.653293] vgaarb: bridge control possible 0000:00:02.0
[ 0.653895] PCI: Using ACPI for IRQ routing
[ 0.668195] PCI: pci_cache_line_size set to 64 bytes
[ 0.668368] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.668373] reserve RAM buffer: 00000000dbff0000 - 00000000dbffffff
[ 0.668517] NetLabel: Initializing
[ 0.668966] NetLabel: domain hash size = 128
[ 0.669429] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.669930] NetLabel: unlabeled traffic allowed by default
[ 0.669987] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[ 0.670555] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.671614] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[ 0.689996] Switching to clocksource hpet
[ 0.691377] Switched to NOHz mode on CPU #0
[ 0.691471] Switched to NOHz mode on CPU #1
[ 0.691704] Switched to NOHz mode on CPU #2
[ 0.691803] Switched to NOHz mode on CPU #3
[ 0.696473] pnp: PnP ACPI init
[ 0.697273] ACPI: bus type pnp registered
[ 0.697831] pnp 00:00: [bus 00-ff]
[ 0.697833] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.697835] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.697836] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.697838] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.697840] pnp 00:00: [mem 0xdc000000-0xffdfffff window]
[ 0.697867] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[ 0.697879] pnp 00:01: [io 0x0060]
[ 0.697880] pnp 00:01: [io 0x0064]
[ 0.697904] pnp 00:01: [irq 1]
[ 0.697923] pnp 00:01: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.697929] pnp 00:02: [io 0x0000-0x000f]
[ 0.697930] pnp 00:02: [io 0x0080-0x008f]
[ 0.697932] pnp 00:02: [io 0x00c0-0x00df]
[ 0.697933] pnp 00:02: [dma 4]
[ 0.697947] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.697990] pnp 00:03: [irq 12]
[ 0.698006] pnp 00:03: Plug and Play ACPI device, IDs PNP0f03 (active)
[ 0.698016] pnp 00:04: [io 0x0378-0x037f]
[ 0.698017] pnp 00:04: [io 0x0778-0x077f]
[ 0.698034] pnp 00:04: [irq 7]
[ 0.698050] pnp 00:04: Plug and Play ACPI device, IDs PNP0400 (active)
[ 0.698074] pnp 00:05: [io 0x0070-0x0071]
[ 0.698090] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.698120] pnp 00:06: [irq 0 disabled]
[ 0.698137] pnp 00:06: [irq 8]
[ 0.698139] pnp 00:06: [mem 0xfed00000-0xfed003ff]
[ 0.698169] system 00:06: [mem 0xfed00000-0xfed003ff] has been reserved
[ 0.698729] system 00:06: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
[ 0.699061] pnp: PnP ACPI: found 7 devices
[ 0.699518] ACPI: ACPI bus type pnp unregistered
[ 0.741466] PCI: max bus depth: 1 pci_try_num: 2
[ 0.741505] pci 0000:00:18.0: PCI bridge to [bus 01-01]
[ 0.742067] pci 0000:00:19.0: PCI bridge to [bus 02-02]
[ 0.742643] pci 0000:00:18.0: setting latency timer to 64
[ 0.742672] pci 0000:00:19.0: setting latency timer to 64
[ 0.742682] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.742684] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[ 0.742686] pci_bus 0000:01: resource 4 [io 0x0000-0xffff]
[ 0.742687] pci_bus 0000:01: resource 5 [mem 0x00000000-0xffffffff]
[ 0.742689] pci_bus 0000:02: resource 4 [io 0x0000-0xffff]
[ 0.742690] pci_bus 0000:02: resource 5 [mem 0x00000000-0xffffffff]
[ 0.742725] NET: Registered protocol family 2
[ 0.743245] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.744399] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.745341] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.745946] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.746483] TCP reno registered
[ 0.746741] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.747152] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.747736] NET: Registered protocol family 1
[ 0.748215] pci 0000:00:02.0: Boot video device
[ 0.748347] PCI: CLS 0 bytes, default 64
[ 0.748380] Unpacking initramfs...
[ 0.998994] Freeing initrd memory: 1928k freed
[ 1.000100] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 1.000721] apm: disabled - APM is not SMP safe.
[ 1.001483] audit: initializing netlink socket (disabled)
[ 1.002074] type=2000 audit(1321658696.999:1): initialized
[ 1.006641] highmem bounce pool size: 64 pages
[ 1.007252] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.014298] VFS: Disk quotas dquot_6.5.2
[ 1.014895] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.015597] msgmni has been set to 1677
[ 1.016559] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.017705] io scheduler noop registered
[ 1.018547] io scheduler deadline registered
[ 1.019100] io scheduler cfq registered (default)
[ 1.019850] ERST: Table is not found!
[ 1.020417] GHES: HEST is not enabled!
[ 1.020950] isapnp: Scanning for PnP cards...
[ 1.444524] isapnp: No Plug & Play device found
[ 1.445224] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.635229] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 1.636615] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.636775] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.637525] mousedev: PS/2 mouse device common for all mice
[ 1.638245] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.639429] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 1.640333] rtc0: alarms up to one day, 114 bytes nvram, hpet irqs
[ 1.640893] cpuidle: using governor ladder
[ 1.641368] cpuidle: using governor menu
[ 1.641950] TCP cubic registered
[ 1.642381] NET: Registered protocol family 17
[ 1.642860] Registering the dns_resolver key type
[ 1.643396] Using IPI No-Shortcut mode
[ 1.644281] PM: Hibernation image not present or could not be loaded.
[ 1.644289] registered taskstats version 1
[ 1.647200] rtc_cmos 00:05: setting system clock to 2011-11-18 23:24:58 UTC (1321658698)
[ 1.648040] Initializing network drop monitor service
[ 1.648717] Freeing unused kernel memory: 508k freed
[ 1.649359] Write protecting the kernel text: 3476k
[ 1.649997] Write protecting the kernel read-only data: 1076k
[ 1.657723] udevd[48]: starting version 175
[ 1.689475] SCSI subsystem initialized
[ 1.690583] usbcore: registered new interface driver usbfs
[ 1.691557] usbcore: registered new interface driver hub
[ 1.692267] usbcore: registered new device driver usb
[ 1.695370] libata version 3.00 loaded.
[ 1.695619] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.696346] ahci 0000:00:1f.2: version 3.0
[ 1.696345] ehci_hcd: block sizes: qh 64 qtd 96 itd 160 sitd 96
[ 1.696401] ahci 0000:00:1f.2: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.697709] ahci 0000:00:1f.2: irq 40 for MSI/MSI-X
[ 1.697776] ahci: SSS flag set, parallel bus scan disabled
[ 1.698617] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
[ 1.699390] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.699391] ohci_hcd: block sizes: ed 64 td 64
[ 1.701787] ahci 0000:00:1f.2: flags: 64bit ncq stag only ccc
[ 1.702446] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.704392] scsi0 : ahci
[ 1.705119] scsi1 : ahci
[ 1.705665] ata1: SATA max UDMA/133 abar m8192@0xf0500000 port 0xf0500100 irq 40
[ 1.706586] ata2: SATA max UDMA/133 abar m8192@0xf0500000 port 0xf0500180 irq 40
[ 1.707792] ohci_hcd 0000:00:1f.4: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.708518] ohci_hcd 0000:00:1f.4: setting latency timer to 64
[ 1.708531] ohci_hcd 0000:00:1f.4: OHCI Host Controller
[ 1.709119] ohci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 1
[ 1.710129] ohci_hcd 0000:00:1f.4: created debug files
[ 1.710170] ohci_hcd 0000:00:1f.4: irq 23, io mem 0xf0502000
[ 1.765639] ohci_hcd 0000:00:1f.4: OHCI controller state
[ 1.765674] ohci_hcd 0000:00:1f.4: OHCI 1.0, NO legacy support registers
[ 1.765703] ohci_hcd 0000:00:1f.4: control 0x283 RWC HCFS=operational CBSR=3
[ 1.765731] ohci_hcd 0000:00:1f.4: cmdstatus 0x00000 SOC=0
[ 1.765756] ohci_hcd 0000:00:1f.4: intrstatus 0x00000000
[ 1.765780] ohci_hcd 0000:00:1f.4: intrenable 0x8000005a MIE RHSC UE RD WDH
[ 1.765818] ohci_hcd 0000:00:1f.4: hcca frame #0001
[ 1.765839] ohci_hcd 0000:00:1f.4: roothub.a 00000208 POTPGT=0 NPS NDP=8(8)
[ 1.765858] ohci_hcd 0000:00:1f.4: roothub.b 00000000 PPCM=0000 DR=0000
[ 1.765875] ohci_hcd 0000:00:1f.4: roothub.status 00008000 DRWE
[ 1.765893] ohci_hcd 0000:00:1f.4: roothub.portstatus [0] 0x00010101 CSC PPS CCS
[ 1.765909] ohci_hcd 0000:00:1f.4: roothub.portstatus [1] 0x00000100 PPS
[ 1.765924] ohci_hcd 0000:00:1f.4: roothub.portstatus [2] 0x00000100 PPS
[ 1.765938] ohci_hcd 0000:00:1f.4: roothub.portstatus [3] 0x00000100 PPS
[ 1.765952] ohci_hcd 0000:00:1f.4: roothub.portstatus [4] 0x00000100 PPS
[ 1.765965] ohci_hcd 0000:00:1f.4: roothub.portstatus [5] 0x00000100 PPS
[ 1.765977] ohci_hcd 0000:00:1f.4: roothub.portstatus [6] 0x00000100 PPS
[ 1.765989] ohci_hcd 0000:00:1f.4: roothub.portstatus [7] 0x00000100 PPS
[ 1.766011] usb usb1: default language 0x0409
[ 1.766021] usb usb1: udev 1, busnum 1, minor = 0
[ 1.766028] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.766827] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.767749] usb usb1: Product: OHCI Host Controller
[ 1.768314] usb usb1: Manufacturer: Linux 3.1.1 ohci_hcd
[ 1.768914] usb usb1: SerialNumber: 0000:00:1f.4
[ 1.769687] usb usb1: usb_probe_device
[ 1.769690] usb usb1: configuration #1 chosen from 1 choice
[ 1.769698] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 1.769714] hub 1-0:1.0: usb_probe_interface
[ 1.769716] hub 1-0:1.0: usb_probe_interface - got id
[ 1.769718] hub 1-0:1.0: USB hub found
[ 1.770088] hub 1-0:1.0: 8 ports detected
[ 1.770544] hub 1-0:1.0: standalone hub
[ 1.770545] hub 1-0:1.0: no power switching (usb 1.0)
[ 1.770546] hub 1-0:1.0: global over-current protection
[ 1.770548] hub 1-0:1.0: power on to power good time: 0ms
[ 1.770557] hub 1-0:1.0: local power source is good
[ 1.770558] hub 1-0:1.0: no over-current condition exists
[ 1.770560] hub 1-0:1.0: trying to enable port power on non-switchable hub
[ 1.870129] ohci_hcd 0000:00:1f.4: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
[ 1.870135] hub 1-0:1.0: port 1: status 0101 change 0001
[ 1.970154] hub 1-0:1.0: state 7 ports 8 chg 0002 evt 0000
[ 1.970167] hub 1-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
[ 2.026869] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.027551] ata1.00: ATA-6: VBOX HARDDISK, 1.0, max UDMA/133
[ 2.028060] ata1.00: 14888960 sectors, multi 128: LBA48 NCQ (depth 31/32)
[ 2.028821] ata1.00: configured for UDMA/133
[ 2.029583] scsi 0:0:0:0: Direct-Access ATA VBOX HARDDISK 1.0 PQ: 0 ANSI: 5
[ 2.103419] ohci_hcd 0000:00:1f.4: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
[ 2.156828] usb 1-1: new full speed USB device number 2 using ohci_hcd
[ 2.293431] ohci_hcd 0000:00:1f.4: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
[ 2.350182] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.350882] ata2.00: ATAPI: VBOX CD-ROM, 1.0, max UDMA/133
[ 2.351392] ata2.00: applying bridge limits
[ 2.351954] ata2.00: configured for UDMA/100
[ 2.352677] scsi 1:0:0:0: CD-ROM VBOX CD-ROM 1.0 PQ: 0 ANSI: 5
[ 2.357151] sd 0:0:0:0: [sda] 14888960 512-byte logical blocks: (7.62 GB/7.09 GiB)
[ 2.358036] sd 0:0:0:0: [sda] Write Protect is off
[ 2.358521] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.358535] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.359675] sda: sda1
[ 2.360396] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.362471] sr0: scsi3-mmc drive: 32x/32x xa/form2 tray
[ 2.363126] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.364088] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.370104] usb 1-1: ep0 maxpacket = 8
[ 2.378629] usb 1-1: skipped 1 descriptor after interface
[ 2.381610] usb 1-1: default language 0x0409
[ 2.389441] usb 1-1: udev 2, busnum 1, minor = 1
[ 2.389443] usb 1-1: New USB device found, idVendor=0471, idProduct=206c
[ 2.389999] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.390676] usb 1-1: Product: MCE USB IR Receiver- Spinel plusf0r ASUS
[ 2.391217] usb 1-1: Manufacturer: PHILIPS
[ 2.391853] usb 1-1: usb_probe_device
[ 2.391856] usb 1-1: configuration #1 chosen from 1 choice
[ 2.392445] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[ 2.392507] hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
[ 2.395455] usbhid 1-1:1.0: usb_probe_interface
[ 2.395457] usbhid 1-1:1.0: usb_probe_interface - got id
[ 2.413757] input: PHILIPS MCE USB IR Receiver- Spinel plusf0r ASUS as /devices/pci0000:00/0000:00:1f.4/usb1/1-1/1-1:1.0/input/input1
[ 2.414942] usbhid 1-1:1.0: looking for a minor, starting at 0
[ 2.415188] generic-usb 0003:0471:206C.0001: input,hiddev0,hidraw0: USB HID v1.00 Keyboard [PHILIPS MCE USB IR Receiver- Spinel plusf0r ASUS] on usb-0000:00:1f.4-1/input0
[ 2.416535] usbcore: registered new interface driver usbhid
[ 2.417121] usbhid: USB HID core driver
[ 2.508091] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[ 2.508765] EXT4-fs (sda1): write access will be enabled during recovery
[ 3.483818] EXT4-fs (sda1): recovery complete
[ 3.484582] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 3.645441] udevd[182]: starting version 175
[ 3.724759] psmouse serio1: ID: 10 00 64
[ 3.725505] intel_rng: FWH not detected
[ 3.730718] ACPI: acpi_idle registered with cpuidle
[ 3.757536] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input3
[ 3.759367] ACPI: AC Adapter [AC] (on-line)
[ 3.760749] piix4_smbus 0000:00:07.0: SMBus base address uninitialized - upgrade BIOS or use force_addr=0xaddr
[ 3.763734] virtio-pci 0000:00:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 3.764701] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 3.765858] virtio-pci 0000:00:03.0: setting latency timer to 64
[ 3.768255] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 3.769036] parport_pc 00:04: reported by Plug and Play ACPI
[ 3.770409] iTCO_vendor_support: vendor-support=0
[ 3.771609] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
[ 3.772471] ACPI: Power Button [PWRF]
[ 3.773761] input: Sleep Button as /devices/LNXSYSTM:00/LNXSLPBN:00/input/input5
[ 3.773906] ACPI: Sleep Button [SLPF]
[ 3.778477] iTCO_wdt: Found a ICH7-M or ICH7-U TCO device (Version=2, TCOBASE=0x8060)
[ 3.779583] iTCO_wdt: timeout value out of range, using 30
[ 3.780619] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 3.795107] leds_ss4200: no LED devices found
[ 3.805067] ppdev: user-space parallel port driver
[ 3.835673] snd_intel8x0 0000:00:05.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 3.836847] snd_intel8x0 0000:00:05.0: setting latency timer to 64
[ 4.153506] intel8x0_measure_ac97_clock: measured 51066 usecs (4396 samples)
[ 4.154077] intel8x0: measured clock 86084 rejected
[ 4.510170] intel8x0_measure_ac97_clock: measured 52612 usecs (4481 samples)
[ 4.510738] intel8x0: measured clock 85170 rejected
[ 4.866833] intel8x0_measure_ac97_clock: measured 52127 usecs (4394 samples)
[ 4.867403] intel8x0: measured clock 84294 rejected
[ 4.867918] intel8x0: clocking to 48000
[ 4.934179] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 5.596848] Bluetooth: Core ver 2.16
[ 5.597539] NET: Registered protocol family 31
[ 5.598037] Bluetooth: HCI device and connection manager initialized
[ 5.598566] Bluetooth: HCI socket layer initialized
[ 5.599052] Bluetooth: L2CAP socket layer initialized
[ 5.599542] Bluetooth: SCO socket layer initialized
[ 5.602071] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 6.729271] NET: Registered protocol family 10
[ 7.125285] NMI watchdog disabled (cpu0): hardware events not enabled
[ 7.126048] NMI watchdog disabled (cpu1): hardware events not enabled
[ 7.126584] NMI watchdog disabled (cpu2): hardware events not enabled
[ 7.127539] NMI watchdog disabled (cpu3): hardware events not enabled
[ 7.128080] watchdog: failed to be enabled on some cpus
[ 61.213453] usbcore: deregistering interface driver usbhid
[ 61.213990] ohci_hcd 0000:00:1f.4: shutdown urb f4118200 ep1in-intr
[ 61.400154] drivers/usb/core/file.c: removing 0 minor
[ 71.764172] mceusb 1-1:1.0: usb_probe_interface
[ 71.764175] mceusb 1-1:1.0: usb_probe_interface - got id
[ 71.764177] mceusb 1-1:1.0: mceusb_dev_probe called
[ 71.764736] mceusb 1-1:1.0: acceptable inbound endpoint found
[ 71.773794] IR NEC protocol handler initialized
[ 71.775578] IR RC5(x) protocol handler initialized
[ 71.777112] IR RC6 protocol handler initialized
[ 71.778713] IR JVC protocol handler initialized
[ 71.780207] IR Sony protocol handler initialized
[ 71.781746] IR MCE Keyboard/mouse protocol handler initialized
[ 71.784148] lirc_dev: IR Remote Control driver registered, major 252
[ 71.785037] IR LIRC bridge handler initialized
[ 76.775355] usb 1-1: modprobe timed out on ep0in len=0/255
[ 81.788895] usb 1-1: modprobe timed out on ep0in len=2/2
[ 86.804472] usb 1-1: modprobe timed out on ep0in len=0/255
[ 91.816862] usb 1-1: modprobe timed out on ep0in len=2/2
[ 91.843443] Registered IR keymap rc-rc6-mce
[ 91.843997] input: Media Center Ed. eHome Infrared Remote Transceiver (0471:206c) as /devices/pci0000:00/0000:00:1f.4/usb1/1-1/1-1:1.0/rc/rc0/input6
[ 91.845450] rc0: Media Center Ed. eHome Infrared Remote Transceiver (0471:206c) as /devices/pci0000:00/0000:00:1f.4/usb1/1-1/1-1:1.0/rc/rc0
[ 91.846748] input: MCE IR Keyboard/Mouse (mceusb) as /devices/virtual/input/input7
[ 91.848408] rc rc0: lirc_dev: driver ir-lirc-codec (mceusb) registered at minor = 0
[ 91.849445] mceusb 1-1:1.0: Flushing receive buffers
[ 91.850137] mceusb 1-1:1.0: receive request called (size=0x8)
[ 91.851138] mceusb 1-1:1.0: receive request complete (res=0)
[ 91.851796] BUG: unable to handle kernel NULL pointer dereference at 00000002
[ 91.852699] IP: [<f86f120b>] mce_request_packet+0x13b/0x210 [mceusb]
[ 91.853400] *pde = 00000000
[ 91.853400] Oops: 0000 [#1] PREEMPT SMP
[ 91.853400] Modules linked in: rc_rc6_mce ir_lirc_codec lirc_dev ir_mce_kbd_decoder ir_sony_decoder ir_jvc_decoder ir_rc6_decoder ir_rc5_decoder ir_nec_decoder mceusb(+) rc_core ipv6 bnep bluetooth rfkill snd_intel8x0 snd_ac97_codec virtio_net ppdev ac97_bus snd_pcm snd_timer snd iTCO_wdt iTCO_vendor_support parport_pc parport evdev i2c_piix4 ac i2c_core virtio_pci pcspkr soundcore processor snd_page_alloc button psmouse serio_raw ext4 mbcache jbd2 crc16 sr_mod cdrom sd_mod ohci_hcd ahci libahci ehci_hcd libata usbcore scsi_mod [last unloaded: hid]
[ 91.853400]
[ 91.853400] Pid: 1277, comm: modprobe Not tainted 3.1.1 #2 innotek GmbH VirtualBox
[ 91.853400] EIP: 0060:[<f86f120b>] EFLAGS: 00010286 CPU: 0
[ 91.853400] EIP is at mce_request_packet+0x13b/0x210 [mceusb]
[ 91.853400] EAX: 00000000 EBX: f3be5000 ECX: f3970400 EDX: 00000000
[ 91.853400] ESI: ed08cf00 EDI: 00000003 EBP: ed247c94 ESP: ed247c6c
[ 91.853400] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 91.853400] Process modprobe (pid: 1277, ti=ed246000 task=f38c5450 task.ti=ed246000)
[ 91.853400] Stack:
[ 91.853400] ed247c80 ed247ca0 f86f117d ed430190 f86f2ed8 f86f37f8 f3862e1c f3be5000
[ 91.853400] f3862e1c 40408280 ed247ca0 f86f12f7 00000002 ed247dc0 f86f2a43 00000001
[ 91.853400] f86f2d7a f86f2d69 f415f620 f3970404 0000206c f3be5041 00000000 ed754c00
[ 91.853400] Call Trace:
[ 91.853400] [<f86f117d>] ? mce_request_packet+0xad/0x210 [mceusb]
[ 91.853400] [<f86f12f7>] mce_async_out+0x17/0x20 [mceusb]
[ 91.853400] [<f86f2a43>] mceusb_dev_probe+0x919/0xa69 [mceusb]
[ 91.853400] [<c045abb9>] ? printk+0x1d/0x1f
[ 91.853400] [<c0378eb1>] ? __pm_runtime_set_status+0x101/0x1c0
[ 91.853400] [<c0378a36>] ? __pm_runtime_resume+0x46/0x60
[ 91.853400] [<f80a62e4>] usb_probe_interface+0xe4/0x1d0 [usbcore]
[ 91.853400] [<c0370798>] driver_probe_device+0x68/0x170
[ 91.853400] [<c0370931>] __driver_attach+0x91/0xa0
[ 91.853400] [<c03708a0>] ? driver_probe_device+0x170/0x170
[ 91.853400] [<c036f9f9>] bus_for_each_dev+0x49/0x70
[ 91.853400] [<c03704b1>] driver_attach+0x21/0x30
[ 91.853400] [<c03708a0>] ? driver_probe_device+0x170/0x170
[ 91.853400] [<c037018f>] bus_add_driver+0x17f/0x260
[ 91.853400] [<c0370de6>] driver_register+0x66/0x110
[ 91.853400] [<c046151d>] ? mutex_unlock+0xd/0x10
[ 91.853400] [<f80a52a1>] usb_register_driver+0x71/0x140 [usbcore]
[ 91.853400] [<f86f1003>] ? mceusb_set_tx_mask+0x3/0x40 [mceusb]
[ 91.853400] [<f86f501b>] mceusb_dev_init+0x1b/0x38 [mceusb]
[ 91.853400] [<c0101125>] do_one_initcall+0x35/0x170
[ 91.853400] [<f86f5000>] ? 0xf86f4fff
[ 91.853400] [<c0180a25>] sys_init_module+0x905/0x1ac0
[ 91.853400] [<c046345f>] sysenter_do_call+0x12/0x28
[ 91.853400] Code: 7c 11 9b ff 85 c0 89 c6 0f 84 cd 00 00 00 ba d0 80 00 00 89 f8 e8 a6 ab b1 c7 85 c0 89 45 e4 0f 84 97 00 00 00 8b 43 18 8b 4b 0c <0f> b6 50 02 8b 01 c1 e2 0f c1 e0 08 81 ca 00 00 00 40 09 c2 8b
[ 91.853400] EIP: [<f86f120b>] mce_request_packet+0x13b/0x210 [mceusb] SS:ESP 0068:ed247c6c
[ 91.853400] CR2: 0000000000000002
[ 91.900761] ---[ end trace f0ce5f2acc865dd2 ]---
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2011-11-19 0:03 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-11-19 0:03 Ooops while loading od mceusb staging module TomCat
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.