fso-console-image problems

fso-console-image problems

[Mr Dash Four]

I am trying to build the above image for htcdream (MACHINE=htcdream, 
DISTRO=shr), but ran into two problems:

1. The bitbake almost finished when I got an error from 
fso-console-image.bb that "cannot satisfy the following dependencies for 
task-fso-compliance: connman-plugin-udhcp". OK, I edited the recipe for 
the task-fso-compliance recipe and deactivated this plugin (I don't plan 
to use any dhcp clients at all), then removed all traces of 
"task-fso-compliance" to force a complete rebuild of this and restarted 
bitbake. The build was successful this time.

2. I then proceeded to unpack the newly-created 
"fso-console-image-htcdream.tar" (the phone rootfs) into my 
newly-formatted smartcard (a single ext3 partition) and then did the 
same with "modules-2.6.32-*.tar" (the kernel modules). I then used 
fastboot and executed  "fastboot boot zImage-2.6.32-*.fastboot" to load 
the new kernel and boot the smartphone. The phone boots up, but the only 
thing I am seeing is a black-and-white stripes boot up screen (this is a 
splash image embedded into the kernel image) and then nothing happens at 
all.

I then tried passing various combinations of the kernel command line 
parameters via fastboot:

console=tty1 no_console_suspend=1 root=/dev/mmcblk0p1 rootdelay=8 
fbcon=rotate:1
console=tty0 no_console_suspend=1 root=/dev/mmcblk0p1 rootdelay=8 
fbcon=rotate:1
console=tty1 no_console_suspend=1 root=/dev/mmcblk0p1 rootdelay=8 
fbcon=rotate:1 nomodeset

etc etc etc, but to no avail - nothing apart from the damned 
black-and-white stripes screen just sitting there!

As a last resort I then did a complete rebuild (wiped out build/tmp and 
started from scratch with the modified recipe for task-fso-compliance to 
exclude the connman-plugin-udhcp plugin) and when it finished I repeated 
the same steps as above - nothing, exactly the same screen, NADA!

If I build shr-image all is well - the black-and-white-stripes bootup 
screen is soon replaced by the SHR logo and then I get the SHR Desktop 
after a while and I have a GUI. When I try to build "console-image" 
(similar in many ways to fso-console-image - simple cli interface), I am 
stuck also at the same step as above, but with a tiny difference - the 
black-and-white stripes screen is replaced after a short period of time 
with the OpenEmbedded logo with an empty progress bar and then I am 
stuck at this stage - nothing happens after that at all.

What am I doing wrong or am I missing something obvious here? Help is 
very much appreciated!

Re: fso-console-image problems

[Denis 'GNUtoo' Carikli]

What are you using?
SHR-core or openembedded classic?

If you are using shr-core you need to fix that file:
openembedded-core/meta/conf/machine/include/arm/arch-armv6.inc
to include support for armv6-novfp and add a tune file for the CPU of the 
htcdream and then require that cpu tune file in the htcdream machine recipe.

Denis.

Re: fso-console-image problems

[Mr Dash Four]

Denis 'GNUtoo' Carikli wrote:
> What are you using?
> SHR-core or openembedded classic?
>   
Don't know if I am honest - there is a (very good) wiki page I have been 
following to build this -> 
http://www.openembedded.org/wiki/Getting_started. I presume it is 
openembedded classic since I downloaded all the stuff from that page 
(git://github.com/openembedded/openembedded.git is the repository used).

As I indicated earlier, I successfully built the shr-image (GUI-based) - 
it boots up OK on my smartphone, but I have no luck whatsoever with the 
console (i.e. just cli) images - I tried two: "console-image" and 
"fso-console-image", both unsuccessful (they do build, but my smartphone 
is having problems booting up properly with these).

> If you are using shr-core you need to fix that file:
> openembedded-core/meta/conf/machine/include/arm/arch-armv6.inc
> to include support for armv6-novfp and add a tune file for the CPU of the 
> htcdream and then require that cpu tune file in the htcdream machine recipe.
>   
I don't know whether I would need this. I also discovered yesterday that 
there is another openembedded git repository on freesmartphone.org 
(git://git.freesmartphone.org/openembedded.git), but not sure whether 
this is the same as the one I have been using...

Re: fso-console-image problems

[Martin Jansa]

[-- Attachment #1: Type: text/plain, Size: 2535 bytes --]

On Fri, Dec 02, 2011 at 02:08:07PM +0000, Mr Dash Four wrote:
> 
> 
> Denis 'GNUtoo' Carikli wrote:
> > What are you using?
> > SHR-core or openembedded classic?
> >   
> Don't know if I am honest - there is a (very good) wiki page I have been 
> following to build this -> 
> http://www.openembedded.org/wiki/Getting_started. I presume it is 
> openembedded classic since I downloaded all the stuff from that page 
> (git://github.com/openembedded/openembedded.git is the repository used).

So yes this is OE-classic.

For building SHR you should follow SHR instructions:
http://wiki.shr-project.org/trac/wiki/Building%20SHR

Where are instructions for building from OE-classic as well as new
layers, but with htcdream there is problem in oe-core, see this thread:
http://lists.linuxtogo.org/pipermail/openembedded-core/2011-October/010993.html
  
> As I indicated earlier, I successfully built the shr-image (GUI-based) - 
> it boots up OK on my smartphone, but I have no luck whatsoever with the 
> console (i.e. just cli) images - I tried two: "console-image" and 
> "fso-console-image", both unsuccessful (they do build, but my smartphone 
> is having problems booting up properly with these).

I'm not familiar with htcdream, but this looks like some problem with kernel fb 
driver, you can try to boot shr-image, setup ssh access and then
shutdown xserver (with /etc/init.d/xserver-nodm stop) to see if you get
console login (check inittab if it's starting getty there) and also try
other vts with chvt.

If it works you can prepare console-image with right
/etc/network/interfaces to be able to ssh in as soon as it boots and
then debug those stripes over ssh too.

Well if you can get serial console to htcdream then it would be even
easier.

> > If you are using shr-core you need to fix that file:
> > openembedded-core/meta/conf/machine/include/arm/arch-armv6.inc
> > to include support for armv6-novfp and add a tune file for the CPU of the 
> > htcdream and then require that cpu tune file in the htcdream machine recipe.
> >   
> I don't know whether I would need this. I also discovered yesterday that 
> there is another openembedded git repository on freesmartphone.org 
> (git://git.freesmartphone.org/openembedded.git), but not sure whether 
> this is the same as the one I have been using...

This is usually used only by FSO people without R/W access to OE git to
prepare some changes.

Cheers,

-- 
Martin 'JaMa' Jansa     jabber: Martin.Jansa@gmail.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 205 bytes --]

Re: fso-console-image problems

[Mr Dash Four]

> So yes this is OE-classic.
>
> For building SHR you should follow SHR instructions:
> http://wiki.shr-project.org/trac/wiki/Building%20SHR
>   
I see. Truth be told, this was the first thing I tried to do, but later 
on decided to use openembedded as my ultimate aim is to have a cli image 
(with less stuff on it as I don't want/need the gui). I think the 
"shr-image" target I build is similar, if not the same, as the building 
of the SHR - a link to which you provided above.

> Where are instructions for building from OE-classic as well as new
> layers, but with htcdream there is problem in oe-core, see this thread:
> http://lists.linuxtogo.org/pipermail/openembedded-core/2011-October/010993.html
>   
Interesting, but thankfully that doesn't apply to me, right?

> I'm not familiar with htcdream, but this looks like some problem with kernel fb 
> driver, you can try to boot shr-image, setup ssh access and then
> shutdown xserver (with /etc/init.d/xserver-nodm stop) to see if you get
> console login (check inittab if it's starting getty there) and also try
> other vts with chvt.
>   
The phone, as far as I know, is not connected anywhere - I don't have a 
working wifi/gsm etc - fastboot uses the usb link to transfer (and boot) 
the image. Is it possible to, somehow, use usb to connect to the phone 
this way (if so, how)? As you probably have gathered by now, I am a n00b 
when it comes to this smartphone/embedded devices business, so would 
need a bit of help with it. What is "vts" and "chvt"?

I was thinking (that was plan B) to specify runlevel 3, not 5, thus 
forcing a console log in (provided there is one!) - don't know if this 
works on smartphones though! I already discovered that "nomodeset" isn't 
working, sadly!

> If it works you can prepare console-image with right
> /etc/network/interfaces to be able to ssh in as soon as it boots and
> then debug those stripes over ssh too.
>   
This is what I can't figure out - how can I get connectivity on this 
phone if none of my wifi/gms is up and running?

> Well if you can get serial console to htcdream then it would be even
> easier.
>   
That is way over my head I am afraid!

>> I don't know whether I would need this. I also discovered yesterday that 
>> there is another openembedded git repository on freesmartphone.org 
>> (git://git.freesmartphone.org/openembedded.git), but not sure whether 
>> this is the same as the one I have been using...
>>     
>
> This is usually used only by FSO people without R/W access to OE git to
> prepare some changes.
>   
So, I shouldn't use it then?

> Cheers,
>   
Thanks JaMa, your help is appreciated!

Re: fso-console-image problems

[Martin Jansa]

[-- Attachment #1: Type: text/plain, Size: 3653 bytes --]

On Fri, Dec 02, 2011 at 03:12:44PM +0000, Mr Dash Four wrote:
> 
> > So yes this is OE-classic.
> >
> > For building SHR you should follow SHR instructions:
> > http://wiki.shr-project.org/trac/wiki/Building%20SHR
> >   
> I see. Truth be told, this was the first thing I tried to do, but later 
> on decided to use openembedded as my ultimate aim is to have a cli image 
> (with less stuff on it as I don't want/need the gui). I think the 
> "shr-image" target I build is similar, if not the same, as the building 
> of the SHR - a link to which you provided above.

yes probably similar but at least you would read about diff between
OE-classic and oe-core setup.. but fine

> > Where are instructions for building from OE-classic as well as new
> > layers, but with htcdream there is problem in oe-core, see this thread:
> > http://lists.linuxtogo.org/pipermail/openembedded-core/2011-October/010993.html
> >   
> Interesting, but thankfully that doesn't apply to me, right?

No if you decide to stuck with old OE-classic.. but would be great to
get htcdream well supported with oe-core..

> > I'm not familiar with htcdream, but this looks like some problem with kernel fb 
> > driver, you can try to boot shr-image, setup ssh access and then
> > shutdown xserver (with /etc/init.d/xserver-nodm stop) to see if you get
> > console login (check inittab if it's starting getty there) and also try
> > other vts with chvt.
> >   
> The phone, as far as I know, is not connected anywhere - I don't have a 
> working wifi/gsm etc - fastboot uses the usb link to transfer (and boot) 
> the image. Is it possible to, somehow, use usb to connect to the phone 
> this way (if so, how)? As you probably have gathered by now, I am a n00b 
> when it comes to this smartphone/embedded devices business, so would 
> need a bit of help with it. What is "vts" and "chvt"?

Well I was expecting that setting usbnet (g_ether kernel module) is easy
on htcdream as it's easy on other devices and that you can load it on
boot and check that usb0 is set to auto.

vt - virtual terminal
chvt - change foreground virtual terminal

as sometimes Xserver is started on different vt then where getty is
enabled, but depends on config and I'm not familiar with htcdream ..

> I was thinking (that was plan B) to specify runlevel 3, not 5, thus 
> forcing a console log in (provided there is one!) - don't know if this 
> works on smartphones though! I already discovered that "nomodeset" isn't 
> working, sadly!

you need to have getty enabled in inittab ie:
t1:2345:respawn:/sbin/getty 38400 tty1

> 
> > If it works you can prepare console-image with right
> > /etc/network/interfaces to be able to ssh in as soon as it boots and
> > then debug those stripes over ssh too.
> >   
> This is what I can't figure out - how can I get connectivity on this 
> phone if none of my wifi/gms is up and running?

usbnet is usually easiest

> > Well if you can get serial console to htcdream then it would be even
> > easier.
> >   
> That is way over my head I am afraid!
> 
> >> I don't know whether I would need this. I also discovered yesterday that 
> >> there is another openembedded git repository on freesmartphone.org 
> >> (git://git.freesmartphone.org/openembedded.git), but not sure whether 
> >> this is the same as the one I have been using...
> >>     
> >
> > This is usually used only by FSO people without R/W access to OE git to
> > prepare some changes.
> >   
> So, I shouldn't use it then?

yes, don't use it

Cheers,
-- 
Martin 'JaMa' Jansa     jabber: Martin.Jansa@gmail.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 205 bytes --]

Re: fso-console-image problems

[Mr Dash Four]

Thanks again, JaMa,


>> Interesting, but thankfully that doesn't apply to me, right?
>>     
>
> No if you decide to stuck with old OE-classic.. but would be great to
> get htcdream well supported with oe-core..
>   
Once I get my phone up and running I'll give it a go - I've been 
following the discussion about oe-classic/oe-core with interest, so I am 
willing to help out if I can.

  

>> The phone, as far as I know, is not connected anywhere - I don't have a 
>> working wifi/gsm etc - fastboot uses the usb link to transfer (and boot) 
>> the image. Is it possible to, somehow, use usb to connect to the phone 
>> this way (if so, how)? As you probably have gathered by now, I am a n00b 
>> when it comes to this smartphone/embedded devices business, so would 
>> need a bit of help with it. What is "vts" and "chvt"?
>>     
>
> Well I was expecting that setting usbnet (g_ether kernel module) is easy
> on htcdream as it's easy on other devices and that you can load it on
> boot and check that usb0 is set to auto.
>   
Ah, right, in other words connecting the device (my phone) via usb *is* 
possible, right? If so, I presume this "usb0" interface acts in a 
similar fashion as my "eth0" for example (ifconfig, route etc can be 
applied to it), right? Quite a revelation to me this! How do I get it 
connected on the "host" side (on my PC on which the usb is used) - do I 
see a similar adapter on it as well? How does that work then?

> vt - virtual terminal
> chvt - change foreground virtual terminal
>
> as sometimes Xserver is started on different vt then where getty is
> enabled, but depends on config and I'm not familiar with htcdream ..
>   
Noted, thanks!

>> I was thinking (that was plan B) to specify runlevel 3, not 5, thus 
>> forcing a console log in (provided there is one!) - don't know if this 
>> works on smartphones though! I already discovered that "nomodeset" isn't 
>> working, sadly!
>>     
>
> you need to have getty enabled in inittab ie:
> t1:2345:respawn:/sbin/getty 38400 tty1
>   
I'll check that at first opportunity - is it possible that *might* be 
the reason I am not getting anywhere with my console-image rootfs? I 
haven't checked the inittab there ... will do that when I get home tonight!

>> This is what I can't figure out - how can I get connectivity on this 
>> phone if none of my wifi/gms is up and running?
>>     
>
> usbnet is usually easiest
>   
So, I presume this usbnet is a point-to-point adapted, is it? Do I have 
to set up special routing (i.e. with route add etc) for it? Do I have to 
give it an ip address from the net I am on my host PC or is this different?

Re: fso-console-image problems

[Martin Jansa]

[-- Attachment #1: Type: text/plain, Size: 3163 bytes --]

On Fri, Dec 02, 2011 at 04:20:53PM +0000, Mr Dash Four wrote:
> Thanks again, JaMa,
> 
> 
> >> Interesting, but thankfully that doesn't apply to me, right?
> >>     
> >
> > No if you decide to stuck with old OE-classic.. but would be great to
> > get htcdream well supported with oe-core..
> >   
> Once I get my phone up and running I'll give it a go - I've been 
> following the discussion about oe-classic/oe-core with interest, so I am 
> willing to help out if I can.

Great!

> >> The phone, as far as I know, is not connected anywhere - I don't have a 
> >> working wifi/gsm etc - fastboot uses the usb link to transfer (and boot) 
> >> the image. Is it possible to, somehow, use usb to connect to the phone 
> >> this way (if so, how)? As you probably have gathered by now, I am a n00b 
> >> when it comes to this smartphone/embedded devices business, so would 
> >> need a bit of help with it. What is "vts" and "chvt"?
> >>     
> >
> > Well I was expecting that setting usbnet (g_ether kernel module) is easy
> > on htcdream as it's easy on other devices and that you can load it on
> > boot and check that usb0 is set to auto.
> >   
> Ah, right, in other words connecting the device (my phone) via usb *is* 
> possible, right? If so, I presume this "usb0" interface acts in a 
> similar fashion as my "eth0" for example (ifconfig, route etc can be 
> applied to it), right? Quite a revelation to me this! How do I get it 
> connected on the "host" side (on my PC on which the usb is used) - do I 
> see a similar adapter on it as well? How does that work then?

Every usb networking howto will help you with this :).

> > vt - virtual terminal
> > chvt - change foreground virtual terminal
> >
> > as sometimes Xserver is started on different vt then where getty is
> > enabled, but depends on config and I'm not familiar with htcdream ..
> >   
> Noted, thanks!
> 
> >> I was thinking (that was plan B) to specify runlevel 3, not 5, thus 
> >> forcing a console log in (provided there is one!) - don't know if this 
> >> works on smartphones though! I already discovered that "nomodeset" isn't 
> >> working, sadly!
> >>     
> >
> > you need to have getty enabled in inittab ie:
> > t1:2345:respawn:/sbin/getty 38400 tty1
> >   
> I'll check that at first opportunity - is it possible that *might* be 
> the reason I am not getting anywhere with my console-image rootfs? I 
> haven't checked the inittab there ... will do that when I get home tonight!
> 
> >> This is what I can't figure out - how can I get connectivity on this 
> >> phone if none of my wifi/gms is up and running?
> >>     
> >
> > usbnet is usually easiest
> >   
> So, I presume this usbnet is a point-to-point adapted, is it? Do I have 
> to set up special routing (i.e. with route add etc) for it? Do I have to 
> give it an ip address from the net I am on my host PC or is this different?

usualy you use IPs from private range and if you want to access internet
from your phone you just setup masquerade in your iptables on PC.

Cheers,

-- 
Martin 'JaMa' Jansa     jabber: Martin.Jansa@gmail.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 205 bytes --]

Re: fso-console-image problems

[Denis 'GNUtoo' Carikli]

>I'm not familiar with htcdream, but this looks like some problem with kernel 
fb 
>driver, you can try to boot shr-image, setup ssh access and then
>shutdown xserver (with /etc/init.d/xserver-nodm stop) to see if you get
>console login (check inittab if it's starting getty there) and also try
>other vts with chvt.
The framebuffer console was disabled in the kernel because it could make the 
phone freeze when Xorg stopped...

Denis.

Re: fso-console-image problems

[Mr Dash Four]

[-- Attachment #1: Type: text/plain, Size: 1686 bytes --]


> The framebuffer console was disabled in the kernel because it could make the 
> phone freeze when Xorg stopped...
>   
Should I refrain from attempting what JaMa suggested then?

On a separate note, I just checked my "fso-consol-image" inittab file 
and the last statement there is indeed as JaMa suggested: 
"1:2345:respawn:/sbin/getty 38400 tty1"

I am attaching the complete inittab file (hope the mailing list daemon 
won't mind!). I tried running at level 3 (changed the 5 in 
id:5:initdefault: to 3), but no luck there either - the same 
black-and-white stripes screen and that is it...

# /etc/inittab: init(8) configuration.
# $Id: inittab,v 1.91 2002/01/25 13:35:21 miquels Exp $

# The default runlevel.
id:5:initdefault:

# Boot-time system configuration/initialization script.
# This is run first except when booting in emergency (-b) mode.
si::sysinit:/etc/init.d/rcS

# What to do in single-user mode.
~~:S:wait:/sbin/sulogin

# /etc/init.d executes the S and K scripts upon change
# of runlevel.
#
# Runlevel 0 is halt.
# Runlevel 1 is single-user.
# Runlevels 2-5 are multi-user.
# Runlevel 6 is reboot.

l0:0:wait:/etc/init.d/rc 0
l1:1:wait:/etc/init.d/rc 1
l2:2:wait:/etc/init.d/rc 2
l3:3:wait:/etc/init.d/rc 3
l4:4:wait:/etc/init.d/rc 4
l5:5:wait:/etc/init.d/rc 5
l6:6:wait:/etc/init.d/rc 6
# Normally not reached, but fallthrough in case of emergency.
z6:6:respawn:/sbin/sulogin
# /sbin/getty invocations for the runlevels.
#
# The "id" field MUST be the same as the last
# characters of the device (after "tty").
#
# Format:
#  <id>:<runlevels>:<action>:<process>
#

1:2345:respawn:/sbin/getty 38400 tty1

Re: fso-console-image problems

[Mr Dash Four]

[-- Attachment #1: Type: text/plain, Size: 75841 bytes --]


> I'm not familiar with htcdream, but this looks like some problem with kernel fb 
> driver, you can try to boot shr-image, setup ssh access and then
> shutdown xserver (with /etc/init.d/xserver-nodm stop) to see if you get
> console login (check inittab if it's starting getty there) and also try
> other vts with chvt.
>
> If it works you can prepare console-image with right
> /etc/network/interfaces to be able to ssh in as soon as it boots and
> then debug those stripes over ssh too.
>   
Some good news at last! As it turned out, everything on that 
console-image was running (including the getty!), but it is just not 
"displayed" properly on my smartphone's screen. Here is what I did:

Booted up the full shr-htc image and when I got to the GUI, I connected 
to my phone via usb0 (no need for a terminal as the 
/etc/network/interfaces was already setup, usb0 was up and sshd was 
running). I then tried "xserver-nodm stop" - the ssh console tells me 
that the service has stopped, but then my entire smartphone screen (the 
GUI) freezes completely - *no* terminal at all!

When I run "xserver-nodm start" from the ssh terminal again - all is 
well and I could move the "X" cursor and use it as normal. I am 
attaching dmesg-full.log (fetched from /var/log/dmesg) so that you may 
diagnose what is causing this. There is a kernel oops from gpiolib, I 
think - don't know how significant that is! Please note that at the end 
of that file there is output of "ps aux" I used to see what's running.

When I boot up the console-image things are almost exactly the same - 
even though I see the black-and-white stripes screen, in the background 
everything is configured and running (getty, sshd and usb0 - all 
properly configured) - I am able to instantly log in via the ssh and 
apart from the phone's screen which only shows the stripes, in the 
background all is well! I attach additional 3 files from this console 
image:
- dmesg-console.log containing my dmesg logs as well as "ps aux" of 
everything running when I logged in via the ssh;
- frameworkd.log as well as fsousaged.log (all fetched from /var/log/) 
showing some errors - I don't know what they are and I also don't know 
whether they are significant, thus preventing my console to show up on 
the phone's screen.

There was no /var/log/messages or any other log files in /var/log when I 
looked.
[    0.000000] Linux version 2.6.32.9 (bitbake@opmbuild) (gcc version 4.5.3 20110311 (prerelease) (GCC) ) #1 PREEMPT Tue Jul 19 01:17:11 CEST 2011
[    0.000000] CPU: ARMv6-compatible processor [4117b362] revision 2 (ARMv6TEJ), cr=00c5387f
[    0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: trout
[    0.000000] find the smi tag
[    0.000000] parse_tag_smi: smi size = 64
[    0.000000] find the hwid tag
[    0.000000] parse_tag_hwid: hwid = 0x0
[    0.000000] find the skuid tag
[    0.000000] parse_tag_skuid: hwid = 0x1be01
[    0.000000] Ignoring unrecognised tag 0x4d534d74
[    0.000000] find the engineer tag
[    0.000000] parse_tag_engineerid: hwid = 0xffffffff
[    0.000000] AKM Data size = 1018 , 0x89768976, size = 4064
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] On node 0 totalpages: 28160
[    0.000000] free_area_init_node: node 0, pgdat c0424eb8, node_mem_map c046c000
[    0.000000]   Normal zone: 220 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 27940 pages, LIFO batch:7
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 27940
[    0.000000] Kernel command line: board_trout.disable_uart3=0 board_trout.usb_h2w_sw=0 board_trout.disable_sdcard=0 smisize=64  androidboot.baseband=2.22.19.26I androidboot.cid=T-MOB005 androidboot.carrier=TMUK androidboot.keycaps=qwerty androidboot.mode=normal androidboot.serialno=HT91PKV01748 androidboot.bootloader=1.33.2005 console=tty1 root=/dev/mmcblk0p1 rootdelay=8 fbcon=rotate:1 panic=30 mem=110M
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 110MB = 110MB total
[    0.000000] Memory: 106948KB available (3812K code, 458K data, 116K init, 0K highmem)
[    0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:250
[    0.000000] trout_init_irq()
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [tty1] enabled
[    0.000000] Calibrating delay loop... 383.38 BogoMIPS (lpj=1916928)
[    0.219299] Mount-cache hash table entries: 512
[    0.220153] CPU: Testing write buffer coherency: ok
[    0.221343] devtmpfs: initialized
[    0.224029] NET: Registered protocol family 16
[    0.224426] trout_init_gpio: cpld_usb_hw2_sw = 0
[    0.225402] trout_init() revision=128
[    5.861053] ------------[ cut here ]------------
[    5.861175] WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x50/0x11c()
[    5.861236] autorequest GPIO-1
[    5.861297] Modules linked in:
[    5.861389] [<c002a9b0>] (unwind_backtrace+0x0/0xe0) from [<c004dffc>] (warn_slowpath_common+0x48/0x60)
[    5.861511] [<c004dffc>] (warn_slowpath_common+0x48/0x60) from [<c004e050>] (warn_slowpath_fmt+0x28/0x38)
[    5.861633] [<c004e050>] (warn_slowpath_fmt+0x28/0x38) from [<c017c0a0>] (gpio_ensure_requested+0x50/0x11c)
[    5.861724] [<c017c0a0>] (gpio_ensure_requested+0x50/0x11c) from [<c017c220>] (gpio_direction_output+0xb4/0x15c)
[    5.861877] [<c017c220>] (gpio_direction_output+0xb4/0x15c) from [<c000d4cc>] (trout_init+0x54/0x1e8)
[    5.861999] [<c000d4cc>] (trout_init+0x54/0x1e8) from [<c000a468>] (customize_machine+0x18/0x24)
[    5.862121] [<c000a468>] (customize_machine+0x18/0x24) from [<c00254d4>] (do_one_initcall+0x30/0x1a0)
[    5.862243] [<c00254d4>] (do_one_initcall+0x30/0x1a0) from [<c00089a4>] (kernel_init+0x98/0x114)
[    5.862365] [<c00089a4>] (kernel_init+0x98/0x114) from [<c002692c>] (kernel_thread_exit+0x0/0x8)
[    5.862518] ---[ end trace 1b75b31a2719ed1c ]---
[    5.862579] acpu_clock_init()
[    5.862701] ACPU running at 384000 KHz
[    5.971588] bio: create slab <bio-0> at 0
[    5.973388] msm_i2c_probe
[    5.973724] msm_i2c_probe: clk_ctl 35d, 100000 Hz
[    5.976348] Bluetooth: Core ver 2.15
[    5.976806] NET: Registered protocol family 31
[    5.976898] Bluetooth: HCI device and connection manager initialized
[    5.976959] Bluetooth: HCI socket layer initialized
[    5.977447] Switching to clocksource gp_timer
[    5.979553] NET: Registered protocol family 2
[    5.979980] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    5.980773] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    5.981414] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    5.981842] TCP: Hash tables configured (established 4096 bind 4096)
[    5.981903] TCP reno registered
[    5.982299] NET: Registered protocol family 1
[    5.982849] Unpacking initramfs...
[    5.983032] Initramfs unpacking failed: junk in compressed archive
[    5.983764] ------------[ cut here ]------------
[    5.983917] WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x50/0x11c()
[    5.983978] autorequest GPIO-101
[    5.984008] Modules linked in:
[    5.984100] [<c002a9b0>] (unwind_backtrace+0x0/0xe0) from [<c004dffc>] (warn_slowpath_common+0x48/0x60)
[    5.984222] [<c004dffc>] (warn_slowpath_common+0x48/0x60) from [<c004e050>] (warn_slowpath_fmt+0x28/0x38)
[    5.984344] [<c004e050>] (warn_slowpath_fmt+0x28/0x38) from [<c017c0a0>] (gpio_ensure_requested+0x50/0x11c)
[    5.984436] [<c017c0a0>] (gpio_ensure_requested+0x50/0x11c) from [<c017c220>] (gpio_direction_output+0xb4/0x15c)
[    5.984558] [<c017c220>] (gpio_direction_output+0xb4/0x15c) from [<c0032bdc>] (bluetooth_set_power+0x18/0x58)
[    5.984649] [<c0032bdc>] (bluetooth_set_power+0x18/0x58) from [<c0032c34>] (trout_rfkill_probe+0x18/0x88)
[    5.984802] [<c0032c34>] (trout_rfkill_probe+0x18/0x88) from [<c01ab8f8>] (platform_drv_probe+0x18/0x1c)
[    5.984893] [<c01ab8f8>] (platform_drv_probe+0x18/0x1c) from [<c01aaa68>] (driver_probe_device+0x78/0x164)
[    5.985015] [<c01aaa68>] (driver_probe_device+0x78/0x164) from [<c01aabe0>] (__driver_attach+0x8c/0x90)
[    5.985107] [<c01aabe0>] (__driver_attach+0x8c/0x90) from [<c01a9d3c>] (bus_for_each_dev+0x50/0x7c)
[    5.985229] [<c01a9d3c>] (bus_for_each_dev+0x50/0x7c) from [<c01aa3e4>] (bus_add_driver+0x98/0x240)
[    5.985321] [<c01aa3e4>] (bus_add_driver+0x98/0x240) from [<c01aae1c>] (driver_register+0x78/0x13c)
[    5.985443] [<c01aae1c>] (driver_register+0x78/0x13c) from [<c00254d4>] (do_one_initcall+0x30/0x1a0)
[    5.985565] [<c00254d4>] (do_one_initcall+0x30/0x1a0) from [<c00089a4>] (kernel_init+0x98/0x114)
[    5.985656] [<c00089a4>] (kernel_init+0x98/0x114) from [<c002692c>] (kernel_thread_exit+0x0/0x8)
[    5.985748] ---[ end trace 1b75b31a2719ed1d ]---
[    5.986328] smd_init()
[    5.986389] smd_core_init()
[    5.986541] smd_core_init() done
[    5.986633] msm_init_last_radio_log: could not retrieve SMEM_CLKREGIM_BSP
[    5.987457] smem_find(16, 40): wrong size 16424
[    5.987670] smd_alloc_channel() cid=02 size=08192 'SMD_RPCCALL'
[    5.988037] smem_find(25, 40): wrong size 16424
[    5.988098] smd_alloc_channel() cid=11 size=08192 'SMD_DATA5'
[    5.988372] smem_find(26, 40): wrong size 16424
[    5.988433] smd_alloc_channel() cid=12 size=08192 'SMD_DATA6'
[    5.988677] smem_find(27, 40): wrong size 16424
[    5.988739] smd_alloc_channel() cid=13 size=08192 'SMD_DATA7'
[    5.988983] smem_find(31, 40): wrong size 16424
[    5.989044] smd_alloc_channel() cid=17 size=08192 'SMD_DATA11'
[    5.989227] smem_find(47, 40): wrong size 16424
[    5.989288] smd_alloc_channel() cid=33 size=08192 'SMD_CS_A2M'
[    5.989501] smem_find(52, 40): wrong size 16424
[    5.989562] smd_alloc_channel() cid=38 size=08192 'SMD_DATA5_CNTL'
[    5.989746] smem_find(53, 40): wrong size 16424
[    5.989807] smd_alloc_channel() cid=39 size=08192 'SMD_DATA6_CNTL'
[    5.989990] smem_find(54, 40): wrong size 16424
[    5.990051] smd_alloc_channel() cid=40 size=08192 'SMD_DATA7_CNTL'
[    5.992095] SMD: ch 2 1 -> 2
[    5.996002] mdp_probe: initialized
[    5.998107] H2W: Registering H2W (headset) driver
[    6.012207] RPC_TIME_TOD_SET_APPS_BASES:
[    6.012237] 	tick = 2381366
[    6.012237] 	stamp = 859059045
[    6.013183] input: h2w headset as /devices/virtual/input/input0
[    6.021514] ashmem: initialized
[    6.036163] yaffs Jul 19 2011 01:11:10 Installing. 
[    6.036376] msgmni has been set to 209
[    6.046875] adsp: probe
[    6.054962] alg: No test for stdrng (krng)
[    6.055541] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    6.055633] io scheduler noop registered
[    6.055664] io scheduler anticipatory registered (default)
[    6.056304] mddi: init() base=0xc70b8000 irq=16
[    6.118011] mddi cmd send rtd: int 3a000, stat 8063, rtd val d
[    6.118347] mddi: registering panel mddi_c_d263_0000
[    6.118499] mddi: publish: 
[    6.120727] vsync on gpio 97 now 0
[    6.170166] msmfb_probe() installing 320 x 480 panel
[    6.217407] msm_serial: detected port #0
[    6.218200] msm_serial.0: ttyMSM0 at MMIO 0xa9a00000 (irq = 9) is a MSM
[    6.219665] msm_serial: detected port #2
[    6.220092] msm_serial.2: ttyMSM2 at MMIO 0xa9c00000 (irq = 11) is a MSM
[    6.221832] msm_serial: driver initialized
[    6.223266] msm_serial_hs.0: ttyHS0 at MMIO 0xa0200000 (irq = 45) is a MSM HS UART
[    6.224182] msm_serial_hs module loaded
[    6.229248] loop: module loaded
[    6.229461] pmem: 1 init
[    6.230285] pmem_adsp: 0 init
[    6.231262] pmem_camera: 0 init
[    6.233093] msm_nand: allocated dma buffer at ffa0b000, dma_addr 16957000
[    6.233398] msm_nand: read CFG0 = aad400c0 CFG1 = 4745c
[    6.233459] msm_nand: CFG0 cw/page=3 ud_sz=512 ecc_sz=10 spare_sz=5
[    6.233734] msm_nand: NAND_READ_ID = 1500aaec
[    6.233947] msn_nand: nandid 1500aaec status c03120
[    6.234008] msm_nand: manuf Samsung (0xec) device 0xaa blocksz 20000 pagesz 800 size 10000000
[    6.234069] msm_nand: save CFG0 = e8d408c0 CFG1 = 4745c
[    6.234130] msm_nand: CFG0: cw/page=3 ud_sz=516 ecc_sz=10 spare_sz=1 num_addr_cycles=5
[    6.234924] msm_nand: DEV_CMD1: f00f3000
[    6.235076] msm_nand: NAND_EBI2_ECC_BUF_CFG: 1ff
[    6.235137] Creating 6 MTD partitions on "msm_nand":
[    6.235168] 0x0000024c0000-0x000002500000 : "misc"
[    6.237121] 0x0000026c0000-0x000002bc0000 : "recovery"
[    6.248504] 0x000002bc0000-0x000002e40000 : "boot"
[    6.256652] 0x000002e40000-0x000008840000 : "system"
[    6.452789] 0x000008840000-0x00000a640000 : "cache"
[    6.520385] 0x00000a640000-0x000010000000 : "userdata"
[    6.728271] tun: Universal TUN/TAP device driver, 1.6
[    6.728515] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    6.737884] msm72k_udc: msm72k_probe
[    6.738403] msm72k_udc: msm72k_probe() io=c70c8000, irq=47, dma=ffa0c000(1699c000)
[    6.740386] g_ether gadget: using random self ethernet address
[    6.740631] g_ether gadget: using random host ethernet address
[    6.743011] usb0: MAC 82:b8:88:f9:8f:f9
[    6.743194] usb0: HOST MAC 6a:f5:6d:f1:70:64
[    6.744354] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[    6.744598] g_ether gadget: g_ether ready
[    6.744781] msm72k_udc: msm72k_udc: registered gadget driver 'g_ether'
[    6.745971] mice: PS/2 mouse device common for all mice
[    6.748046] msm72k_udc: IDLE -> ONLINE
[    6.748352] hsusb: reset controller
[    6.788513] msm_hsusb_phy_reset: success
[    6.798309] msm_i2c msm_i2c.0: error, status 43c8
[    6.798461] msm_i2c msm_i2c.0: Error during data xfer (-5)
[    6.879974] trout_gpio_irq_handler: got masked interrupt: 0:80
[    6.908355] trout_gpio_irq_handler: got masked interrupt: 0:80
[    6.908630] synaptics_ts_probe: Product Major Version 1
[    6.909515] trout_gpio_irq_handler: got masked interrupt: 0:80
[    6.909729] synaptics_ts_probe: Product Minor Version c
[    6.910552] trout_gpio_irq_handler: got masked interrupt: 0:80
[    6.910797] synaptics_ts_probe: product property 2
[    6.911682] trout_gpio_irq_handler: got masked interrupt: 0:80
[    6.911895] synaptics_ts_probe: device control 81
[    6.912780] trout_gpio_irq_handler: got masked interrupt: 0:80
[    6.912963] synaptics_ts_probe: interrupt enable 3
[    6.915069] synaptics_ts_probe: 0xe0: 1 1 1 2 1 c 0 0
[    6.916351] synaptics_ts_probe: Sensor properties 601
[    6.920257] synaptics_ts_probe: max_x 3480, max_y 5368
[    6.920440] synaptics_ts_probe: inactive_x -80 -80, inactive_y -32 -32
[    6.920654] synaptics_ts_probe: snap_x 240-248 240-248, snap_y 80-88 80-88
[    6.921997] input: synaptics-rmi-touchscreen as /devices/virtual/input/input1
[    6.924652] synaptics_ts_probe: Start touchscreen synaptics-rmi-touchscreen in interrupt mode
[    6.926422] GPIO Input Driver: Start gpio inputs for trout-nav in interrupt mode
[    6.928192] input: trout-nav as /devices/virtual/input/input2
[    6.931213] GPIO Matrix Keypad Driver: Start keypad matrix for trout-keypad-v3 in interrupt mode
[    6.932067] GPIO Input Driver: Start gpio inputs for trout-keypad-v3 in interrupt mode
[    6.932708] GPIO Input Driver: Start gpio inputs for trout-keypad-v3 in interrupt mode
[    6.934600] input: trout-keypad-v3 as /devices/virtual/input/input3
[    6.938293] using input dev h2w headset for key reset
[    6.938629] using input dev trout-nav for key reset
[    6.938812] using input dev trout-keypad-v3 for key reset
[    6.940826] rs30000048:0da5b528 rs30000048:0da5b528: rtc core: registered msm_rtc as rtc0
[    6.941406] AKM8976A compass driver: init
[    6.942321] msm72k_udc: ulpi: write 0x40 to 0x31
[    6.942535] msm72k_udc: ulpi: write 0x1d to 0x0d
[    6.942687] msm72k_udc: ulpi: write 0x1d to 0x10
[    6.942871] msm72k_udc: ept #0 out max:64 head:ffa0c000 bit:0
[    6.943023] msm72k_udc: ept #1 out max:512 head:ffa0c080 bit:1
[    6.943206] msm72k_udc: ept #2 out max:512 head:ffa0c100 bit:2
[    6.943389] msm72k_udc: ept #3 out max:512 head:ffa0c180 bit:3
[    6.943572] msm72k_udc: ept #4 out max:512 head:ffa0c200 bit:4
[    6.943725] msm72k_udc: ept #5 out max:512 head:ffa0c280 bit:5
[    6.943908] msm72k_udc: ept #6 out max:512 head:ffa0c300 bit:6
[    6.944091] msm72k_udc: ept #7 out max:512 head:ffa0c380 bit:7
[    6.944244] msm72k_udc: ept #8 out max:512 head:ffa0c400 bit:8
[    6.944427] msm72k_udc: ept #9 out max:512 head:ffa0c480 bit:9
[    6.944610] msm72k_udc: ept #10 out max:512 head:ffa0c500 bit:10
[    6.944793] msm72k_udc: ept #11 out max:512 head:ffa0c580 bit:11
[    6.944946] msm72k_udc: ept #12 out max:512 head:ffa0c600 bit:12
[    6.945129] msm72k_udc: ept #13 out max:512 head:ffa0c680 bit:13
[    6.945312] msm72k_udc: ept #14 out max:512 head:ffa0c700 bit:14
[    6.945495] msm72k_udc: ept #15 out max:512 head:ffa0c780 bit:15
[    6.945678] msm72k_udc: ept #0 in max:64 head:ffa0c040 bit:16
[    6.945831] msm72k_udc: ept #1 in max:512 head:ffa0c0c0 bit:17
[    6.946014] msm72k_udc: ept #2 in max:512 head:ffa0c140 bit:18
[    6.946197] msm72k_udc: ept #3 in max:512 head:ffa0c1c0 bit:19
[    6.946380] msm72k_udc: ept #4 in max:512 head:ffa0c240 bit:20
[    6.946533] msm72k_udc: ept #5 in max:512 head:ffa0c2c0 bit:21
[    6.946716] msm72k_udc: ept #6 in max:512 head:ffa0c340 bit:22
[    6.946899] msm72k_udc: ept #7 in max:512 head:ffa0c3c0 bit:23
[    6.947052] msm72k_udc: ept #8 in max:512 head:ffa0c440 bit:24
[    6.947235] msm72k_udc: ept #9 in max:512 head:ffa0c4c0 bit:25
[    6.947418] msm72k_udc: ept #10 in max:512 head:ffa0c540 bit:26
[    6.947753] msm72k_udc: ept #11 in max:512 head:ffa0c5c0 bit:27
[    6.947967] msm72k_udc: ept #12 in max:512 head:ffa0c640 bit:28
[    6.948150] msm72k_udc: ept #13 in max:512 head:ffa0c6c0 bit:29
[    6.948303] msm72k_udc: ept #14 in max:512 head:ffa0c740 bit:30
[    6.948486] msm72k_udc: ept #15 in max:512 head:ffa0c7c0 bit:31
[    6.948699] usb: notify offline
[    6.948791] msm_hsusb: enable pullup
[    6.948913] msm72k_udc: ONLINE -> OFFLINE
[    6.949035] msm_hsusb: disable pullup
[    6.949188] usb: notify offline
[    6.969543] input: compass as /devices/virtual/input/input4
[    6.971923] msm_hsusb_phy_reset: success
[    6.972167] smem_find(41, 40): wrong size 16424
[    6.972198] smd_alloc_channel() cid=27 size=08192 'SMD_GPSNMEA'
[    6.976043] Registered led device: blue
[    6.976287] Registered led device: green
[    6.976470] Registered led device: red
[    6.978057] device-mapper: uevent: version 1.0.3
[    6.979644] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    6.980255] Bluetooth: HCI UART driver ver 2.2
[    6.980346] Bluetooth: HCI H4 protocol initialized
[    6.980377] Bluetooth: HCI BCSP protocol initialized
[    6.980407] Bluetooth: HCILL protocol initialized
[    6.981048] sdhci: Secure Digital Host Controller Interface driver
[    6.981109] sdhci: Copyright(c) Pierre Ossman
[    6.982482] mmc0: Qualcomm MSM SDCC at 0x00000000a0400000 irq 24,0 dma 8
[    6.982604] mmc0: 4 bit data mode enabled
[    6.982635] mmc0: MMC clock 144000 -> 50000000 Hz, PCLK 64000000 Hz
[    6.982666] mmc0: Slot eject status = 1
[    6.982696] mmc0: Power save feature enable = 1
[    6.982757] mmc0: DM non-cached buffer at ffa0e000, dma_addr 0x169b9000
[    6.982788] mmc0: DM cmd busaddr 0x169b9000, cmdptr busaddr 0x169b9300
[    6.983825] trout_sdslot_switchvdd: Disabling SD slot power
[    6.984222] mmc1: Qualcomm MSM SDCC at 0x00000000a0500000 irq 26,194 dma 8
[    6.984283] mmc1: 4 bit data mode enabled
[    6.984313] mmc1: MMC clock 144000 -> 50000000 Hz, PCLK 64000000 Hz
[    6.984375] mmc1: Slot eject status = 0
[    6.984405] mmc1: Power save feature enable = 1
[    6.984436] mmc1: DM non-cached buffer at ffa0f000, dma_addr 0x169bb000
[    6.984497] mmc1: DM cmd busaddr 0x169bb000, cmdptr busaddr 0x169bb300
[    6.985107] Registered led device: spotlight
[    6.985351] Registered led device: keyboard-backlight
[    6.985565] Registered led device: button-backlight
[    6.986816] wacom driver registered
[    6.987915] Advanced Linux Sound Architecture Driver Version 1.0.21.
[    6.989410] No device for DAI CODEC_DAI
[    6.989532] No device for DAI CPU_DAI
[    6.989562] msm_soc: create pcms
[    6.990112] asoc: CODEC_DAI <-> CPU_DAI mapping ok
[    6.990142] msm_soc:ALSA MSM Mixer Setting
[    6.993682] ALSA device list:
[    6.993804]   #0: msm-audio (MSM-CARD)
[    6.994567] TCP cubic registered
[    6.996398] NET: Registered protocol family 10
[    6.998016] lo: Disabled Privacy Extensions
[    7.000061] Mobile IPv6
[    7.000152] IPv6 over IPv4 tunneling driver
[    7.001220] sit0: Disabled Privacy Extensions
[    7.002563] ip6tnl0: Disabled Privacy Extensions
[    7.002960] NET: Registered protocol family 17
[    7.003112] NET: Registered protocol family 15
[    7.003204] Bluetooth: L2CAP ver 2.14
[    7.003265] Bluetooth: L2CAP socket layer initialized
[    7.003326] Bluetooth: SCO (Voice Link) ver 0.6
[    7.003356] Bluetooth: SCO socket layer initialized
[    7.003906] Bluetooth: RFCOMM TTY layer initialized
[    7.003997] Bluetooth: RFCOMM socket layer initialized
[    7.004058] Bluetooth: RFCOMM ver 1.11
[    7.004089] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    7.004150] Bluetooth: BNEP filters: protocol multicast
[    7.004180] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    7.004852] clock_late_init() disabled 18 unused clocks
[    7.007843] rs30000048:0da5b528 rs30000048:0da5b528: setting system clock to 2011-12-02 18:48:08 UTC (1322851688)
[    7.008087] Waiting 8sec before mounting root device...
[    7.041076] trout_sdslot_switchvdd: Setting level to 2950
[    7.110015] smem_find(14, 40): wrong size 16424
[    7.110229] smd_alloc_channel() cid=00 size=08192 'SMD_DS'
[    7.111206] smem_find(21, 40): wrong size 16424
[    7.111389] smd_alloc_channel() cid=07 size=08192 'SMD_DATA1'
[    7.112121] smem_find(22, 40): wrong size 16424
[    7.112304] smd_alloc_channel() cid=08 size=08192 'SMD_DATA2'
[    7.113006] smem_find(23, 40): wrong size 16424
[    7.113159] smd_alloc_channel() cid=09 size=08192 'SMD_DATA3'
[    7.113861] smem_find(24, 40): wrong size 16424
[    7.114044] smd_alloc_channel() cid=10 size=08192 'SMD_DATA4'
[    7.116638] trout_sdslot_switchvdd: Setting level to 2750
[    7.277343] mmc1: host does not support reading read-only switch. assuming write-enable.
[    7.277862] mmc1: new high speed SDHC card at address b368
[    7.279327] mmcblk0: mmc1:b368 USD   3.75 GiB 
[    7.280517]  mmcblk0: p1
[   15.022979] EXT3-fs: INFO: recovery required on readonly filesystem.
[   15.023223] EXT3-fs: write access will be enabled during recovery.
[   16.491241] EXT3-fs: recovery complete.
[   16.491882] kjournald starting.  Commit interval 5 seconds
[   16.499267] EXT3-fs: mounted filesystem with writeback data mode.
[   16.499633] VFS: Mounted root (ext3 filesystem) readonly on device 179:1.
[   16.503143] devtmpfs: mounted
[   16.503509] Freeing init memory: 116K
[   17.287750] EXT3 FS on mmcblk0p1, internal journal
[   17.837890] cfg80211: Calling CRDA to update world regulatory domain
[   19.227142] ADDRCONF(NETDEV_UP): usb0: link is not ready
[   21.098266] msm72k_udc: OFFLINE -> ONLINE
[   21.098541] hsusb: reset controller
[   21.189758] msm_hsusb_phy_reset: success
[   21.337707] msm72k_udc: ulpi: write 0x40 to 0x31
[   21.337829] msm72k_udc: ulpi: write 0x1d to 0x0d
[   21.337860] msm72k_udc: ulpi: write 0x1d to 0x10
[   21.337890] msm72k_udc: ept #0 out max:64 head:ffa0c000 bit:0
[   21.337951] msm72k_udc: ept #1 out max:512 head:ffa0c080 bit:1
[   21.337982] msm72k_udc: ept #2 out max:512 head:ffa0c100 bit:2
[   21.338043] msm72k_udc: ept #3 out max:512 head:ffa0c180 bit:3
[   21.338073] msm72k_udc: ept #4 out max:512 head:ffa0c200 bit:4
[   21.338104] msm72k_udc: ept #5 out max:512 head:ffa0c280 bit:5
[   21.338165] msm72k_udc: ept #6 out max:512 head:ffa0c300 bit:6
[   21.338195] msm72k_udc: ept #7 out max:512 head:ffa0c380 bit:7
[   21.338226] msm72k_udc: ept #8 out max:512 head:ffa0c400 bit:8
[   21.338287] msm72k_udc: ept #9 out max:512 head:ffa0c480 bit:9
[   21.338317] msm72k_udc: ept #10 out max:512 head:ffa0c500 bit:10
[   21.338378] msm72k_udc: ept #11 out max:512 head:ffa0c580 bit:11
[   21.338409] msm72k_udc: ept #12 out max:512 head:ffa0c600 bit:12
[   21.338439] msm72k_udc: ept #13 out max:512 head:ffa0c680 bit:13
[   21.338500] msm72k_udc: ept #14 out max:512 head:ffa0c700 bit:14
[   21.338531] msm72k_udc: ept #15 out max:512 head:ffa0c780 bit:15
[   21.338592] msm72k_udc: ept #0 in max:64 head:ffa0c040 bit:16
[   21.338623] msm72k_udc: ept #1 in max:512 head:ffa0c0c0 bit:17
[   21.338653] msm72k_udc: ept #2 in max:512 head:ffa0c140 bit:18
[   21.338714] msm72k_udc: ept #3 in max:512 head:ffa0c1c0 bit:19
[   21.338745] msm72k_udc: ept #4 in max:512 head:ffa0c240 bit:20
[   21.338775] msm72k_udc: ept #5 in max:512 head:ffa0c2c0 bit:21
[   21.338836] msm72k_udc: ept #6 in max:512 head:ffa0c340 bit:22
[   21.338867] msm72k_udc: ept #7 in max:512 head:ffa0c3c0 bit:23
[   21.338928] msm72k_udc: ept #8 in max:512 head:ffa0c440 bit:24
[   21.338958] msm72k_udc: ept #9 in max:512 head:ffa0c4c0 bit:25
[   21.338989] msm72k_udc: ept #10 in max:512 head:ffa0c540 bit:26
[   21.339050] msm72k_udc: ept #11 in max:512 head:ffa0c5c0 bit:27
[   21.339080] msm72k_udc: ept #12 in max:512 head:ffa0c640 bit:28
[   21.339111] msm72k_udc: ept #13 in max:512 head:ffa0c6c0 bit:29
[   21.339172] msm72k_udc: ept #14 in max:512 head:ffa0c740 bit:30
[   21.339202] msm72k_udc: ept #15 in max:512 head:ffa0c7c0 bit:31
[   21.339263] usb: notify offline
[   21.339294] msm_hsusb: enable pullup
[   21.342376] msm72k_udc: msm72k_udc: suspend
[   21.444091] msm72k_udc: msm72k_udc: reset
[   21.446411] msm72k_udc: msm72k_udc: portchange USB_SPEED_HIGH
[   21.549102] msm72k_udc: msm72k_udc: reset
[   21.551422] msm72k_udc: msm72k_udc: portchange USB_SPEED_HIGH
[   21.675598] g_ether gadget: high speed config #1: CDC Ethernet (ECM)
[   21.675720] msm72k_udc: ept #2 in max:64 head:ffa0c140 bit:18
[   21.678527] msm72k_udc: ept #1 in max:512 head:ffa0c0c0 bit:17
[   21.678649] msm72k_udc: ept #1 out max:512 head:ffa0c080 bit:1
[   21.679107] ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready
[   23.832183] request_suspend_state: wakeup (3->0) at 18194614343 (2011-12-02 18:48:25.324340851 UTC)
[   26.898376] init sharp panel
[   28.233245] qmi: smd closed
[   28.233306] SMD: ch 38 1 -> 2
[   28.233337] qmi: smd opened
[   28.234008] qmi: ctl: wds use client_id 0x01
[   29.623535] SMD: ch 0 1 -> 2
[   32.127685] usb0: no IPv6 routers present

root         1  0.0  0.5   1408   568 ?        Ss   18:48   0:00 init [5]  
root         2  0.0  0.0      0     0 ?        S    18:48   0:00 [kthreadd]
root         3  0.0  0.0      0     0 ?        S    18:48   0:00 [ksoftirqd/0]
root         4  0.0  0.0      0     0 ?        S    18:48   0:00 [events/0]
root         5  0.0  0.0      0     0 ?        S    18:48   0:00 [khelper]
root         6  0.0  0.0      0     0 ?        S    18:48   0:00 [async/mgr]
root         7  0.0  0.0      0     0 ?        S    18:48   0:00 [suspend]
root         8  0.0  0.0      0     0 ?        S    18:48   0:00 [sync_supers]
root         9  0.0  0.0      0     0 ?        S    18:48   0:00 [bdi-default]
root        10  0.0  0.0      0     0 ?        S    18:48   0:00 [kblockd/0]
root        11  0.0  0.0      0     0 ?        S    18:48   0:00 [kseriod]
root        12  0.0  0.0      0     0 ?        S    18:48   0:00 [kmmcd]
root        13  0.0  0.0      0     0 ?        S    18:48   0:00 [bluetooth]
root        14  0.0  0.0      0     0 ?        S    18:48   0:00 [kondemand/0]
root        15  0.0  0.0      0     0 ?        S    18:48   0:00 [qmi]
root        16  0.0  0.0      0     0 ?        D    18:48   0:00 [rpcrouter]
root        17  0.0  0.0      0     0 ?        S    18:48   0:00 [detection/0]
root        18  0.0  0.0      0     0 ?        S    18:48   0:00 [krpcserversd]
root        19  0.0  0.0      0     0 ?        S    18:48   0:00 [kswapd0]
root        20  0.0  0.0      0     0 ?        S    18:48   0:00 [aio/0]
root        21  0.0  0.0      0     0 ?        S    18:48   0:00 [crypto/0]
root        30  0.0  0.0      0     0 ?        S    18:48   0:00 [kadspd]
root        32  0.0  0.0      0     0 ?        S    18:48   0:00 [panel_on/0]
root        33  0.0  0.0      0     0 ?        D    18:48   0:00 [msmfb_refreshd]
root        34  0.0  0.0      0     0 ?        S    18:48   0:00 [msm_serial_hs]
root        35  0.0  0.0      0     0 ?        S    18:48   0:00 [mtdblockd]
root        36  0.0  0.0      0     0 ?        S    18:48   0:00 [rmnet/0]
root        37  0.0  0.0      0     0 ?        S    18:48   0:00 [synaptics_wq]
root        38  0.0  0.0      0     0 ?        S    18:48   0:00 [kstriped]
root        39  0.0  0.0      0     0 ?        S    18:48   0:00 [kconservative/0]
root        40  0.0  0.0      0     0 ?        S<   18:48   0:00 [krfcommd]
root        41  0.0  0.0      0     0 ?        S    18:48   0:00 [mmcqd]
root        42  0.0  0.0      0     0 ?        S    18:48   0:00 [flush-179:0]
root        43  0.0  0.0      0     0 ?        S    18:48   0:00 [kjournald]
100        141  0.4  1.1   2596  1180 ?        Ss   18:48   0:04 /usr/bin/dbus-daemon --system
root       144  0.0  3.6  18184  3928 ?        Ssl  18:48   0:00 /usr/sbin/connmand -I usb0,wlan0,dummy0,rmnet0,rmnet1,rmnet2 -r
root       152  0.0  0.7   3664   836 ?        Ss   18:48   0:00 /usr/sbin/sshd
root       155  0.0  0.4   1412   452 ?        Ss   18:48   0:00 /usr/sbin/cron
nobody     159  0.0  0.5   2104   640 ?        S    18:48   0:00 /usr/bin/dnsmasq -7 /etc/dnsmasq.d
root       162  0.0  0.6   2712   692 ?        Ss   18:48   0:00 /sbin/syslogd -n -C64 -m 20
root       164  0.0  0.5   2648   596 ?        Ss   18:48   0:00 /sbin/klogd -n
root       167  0.6  3.5  17904  3796 ?        Ssl  18:48   0:07 /usr/sbin/fsodeviced
root       172  0.3  3.0  16472  3236 ?        Sl   18:48   0:03 /usr/sbin/fsousaged
root       173  0.0  3.2  23988  3472 ?        Ssl  18:48   0:00 /usr/sbin/fsotdld
root       176  2.1 11.3  25740 12192 ?        Ss   18:48   0:24 python /usr/bin/frameworkd
root       179  0.0  2.9  16044  3136 ?        Ssl  18:48   0:00 /usr/sbin/fsoaudiod
root       182  0.0  1.4   3808  1540 ?        Ss   18:48   0:00 /usr/sbin/fso-gpsd -S localhost gpsd -P /var/run/fso-gpsd.pid
root       208  0.0  1.4   3216  1560 ?        S    18:48   0:00 /usr/sbin/atd /var/spool/at
root       210  0.0  0.5   2652   608 tty1     Ss+  18:48   0:00 /sbin/getty 38400 tty1
root       212  0.1  2.3  23172  2532 ?        Ssl  18:48   0:01 /usr/bin/phonefsod
root       235  0.5  3.9  25820  4268 ?        Sl   18:48   0:05 /usr/sbin/fsogsmd
root       243  0.4  4.8  18132  5240 ?        Sl   18:48   0:04 /usr/sbin/fsodatad
root       247  1.0 11.6  23304 12536 ?        S<L  18:48   0:11 /usr/bin/enlightenment
root       259  0.0  1.7   6452  1916 ?        SNs  18:48   0:00 /usr/lib/enlightenment/utils/enlightenment_fm
root       269  0.1  0.0      0     0 ?        ZNs  18:48   0:01 [shr_elm_softkey] <defunct>
root       270  1.0  0.0      0     0 ?        ZNs  18:48   0:11 [vala-terminal] <defunct>
root       314  0.1  1.6   3888  1812 ?        Ss   18:57   0:00 sshd: root@pts/1 
root       316  0.0  0.7   2824   848 pts/1    Ss   18:57   0:00 -sh
root       360  1.8 11.8  23520 12728 pts/1    S<L  19:00   0:07 /usr/bin/enlightenment
root       373  0.0  1.7   6452  1916 ?        SNs  19:00   0:00 /usr/lib/enlightenment/utils/enlightenment_fm
root       383  0.2  0.0      0     0 ?        ZNs  19:00   0:01 [shr_elm_softkey] <defunct>

[    0.000000] Linux version 2.6.32.9 (mr-4@test1.my.net) (gcc version 4.5.3 20110311 (prerelease) (GCC) ) #1 PREEMPT Wed Nov 30 05:28:22 GMT 2011
[    0.000000] CPU: ARMv6-compatible processor [4117b362] revision 2 (ARMv6TEJ), cr=00c5387f
[    0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: trout
[    0.000000] find the smi tag
[    0.000000] parse_tag_smi: smi size = 64
[    0.000000] find the hwid tag
[    0.000000] parse_tag_hwid: hwid = 0x0
[    0.000000] find the skuid tag
[    0.000000] parse_tag_skuid: hwid = 0x1be01
[    0.000000] Ignoring unrecognised tag 0x4d534d74
[    0.000000] find the engineer tag
[    0.000000] parse_tag_engineerid: hwid = 0xffffffff
[    0.000000] AKM Data size = 1018 , 0x89768976, size = 4064
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] On node 0 totalpages: 28160
[    0.000000] free_area_init_node: node 0, pgdat c0424eb8, node_mem_map c046c000
[    0.000000]   Normal zone: 220 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 27940 pages, LIFO batch:7
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 27940
[    0.000000] Kernel command line: board_trout.disable_uart3=0 board_trout.usb_h2w_sw=0 board_trout.disable_sdcard=0 smisize=64  androidboot.baseband=2.22.19.26I androidboot.cid=T-MOB005 androidboot.carrier=TMUK androidboot.keycaps=qwerty androidboot.mode=normal androidboot.serialno=HT91PKV01748 androidboot.bootloader=1.33.2005 console=tty1 root=/dev/mmcblk0p1 rootdelay=8 fbcon=rotate:1 panic=30 mem=110M
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 110MB = 110MB total
[    0.000000] Memory: 106948KB available (3812K code, 458K data, 116K init, 0K highmem)
[    0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:250
[    0.000000] trout_init_irq()
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [tty1] enabled
[    0.000000] Calibrating delay loop... 383.38 BogoMIPS (lpj=1916928)
[    0.219268] Mount-cache hash table entries: 512
[    0.220123] CPU: Testing write buffer coherency: ok
[    0.221343] devtmpfs: initialized
[    0.224029] NET: Registered protocol family 16
[    0.224456] trout_init_gpio: cpld_usb_hw2_sw = 0
[    0.224609] trout_gpio_irq_handler: got masked interrupt: 0:10
[    0.224700] trout_gpio_irq_handler: got masked interrupt: 1:01
[    0.225616] trout_init() revision=128
[    5.648437] ------------[ cut here ]------------
[    5.648559] WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x50/0x11c()
[    5.648651] autorequest GPIO-1
[    5.648681] Modules linked in:
[    5.648803] [<c002a9b0>] (unwind_backtrace+0x0/0xe0) from [<c004dffc>] (warn_slowpath_common+0x48/0x60)
[    5.648925] [<c004dffc>] (warn_slowpath_common+0x48/0x60) from [<c004e050>] (warn_slowpath_fmt+0x28/0x38)
[    5.649017] [<c004e050>] (warn_slowpath_fmt+0x28/0x38) from [<c017c0a0>] (gpio_ensure_requested+0x50/0x11c)
[    5.649139] [<c017c0a0>] (gpio_ensure_requested+0x50/0x11c) from [<c017c220>] (gpio_direction_output+0xb4/0x15c)
[    5.649291] [<c017c220>] (gpio_direction_output+0xb4/0x15c) from [<c000d4cc>] (trout_init+0x54/0x1e8)
[    5.649414] [<c000d4cc>] (trout_init+0x54/0x1e8) from [<c000a468>] (customize_machine+0x18/0x24)
[    5.649536] [<c000a468>] (customize_machine+0x18/0x24) from [<c00254d4>] (do_one_initcall+0x30/0x1a0)
[    5.649658] [<c00254d4>] (do_one_initcall+0x30/0x1a0) from [<c00089a4>] (kernel_init+0x98/0x114)
[    5.649780] [<c00089a4>] (kernel_init+0x98/0x114) from [<c002692c>] (kernel_thread_exit+0x0/0x8)
[    5.649902] ---[ end trace 1b75b31a2719ed1c ]---
[    5.649963] acpu_clock_init()
[    5.650115] ACPU running at 384000 KHz
[    5.759033] bio: create slab <bio-0> at 0
[    5.760894] msm_i2c_probe
[    5.761230] msm_i2c_probe: clk_ctl 35d, 100000 Hz
[    5.763793] Bluetooth: Core ver 2.15
[    5.764282] NET: Registered protocol family 31
[    5.764343] Bluetooth: HCI device and connection manager initialized
[    5.764404] Bluetooth: HCI socket layer initialized
[    5.764923] Switching to clocksource gp_timer
[    5.766998] NET: Registered protocol family 2
[    5.767395] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    5.768218] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    5.768829] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    5.769104] TCP: Hash tables configured (established 4096 bind 4096)
[    5.769165] TCP reno registered
[    5.769592] NET: Registered protocol family 1
[    5.770141] Unpacking initramfs...
[    5.770294] Initramfs unpacking failed: junk in compressed archive
[    5.771118] ------------[ cut here ]------------
[    5.771270] WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x50/0x11c()
[    5.771331] autorequest GPIO-101
[    5.771362] Modules linked in:
[    5.771453] [<c002a9b0>] (unwind_backtrace+0x0/0xe0) from [<c004dffc>] (warn_slowpath_common+0x48/0x60)
[    5.771575] [<c004dffc>] (warn_slowpath_common+0x48/0x60) from [<c004e050>] (warn_slowpath_fmt+0x28/0x38)
[    5.771667] [<c004e050>] (warn_slowpath_fmt+0x28/0x38) from [<c017c0a0>] (gpio_ensure_requested+0x50/0x11c)
[    5.771789] [<c017c0a0>] (gpio_ensure_requested+0x50/0x11c) from [<c017c220>] (gpio_direction_output+0xb4/0x15c)
[    5.771911] [<c017c220>] (gpio_direction_output+0xb4/0x15c) from [<c0032bdc>] (bluetooth_set_power+0x18/0x58)
[    5.772003] [<c0032bdc>] (bluetooth_set_power+0x18/0x58) from [<c0032c34>] (trout_rfkill_probe+0x18/0x88)
[    5.772125] [<c0032c34>] (trout_rfkill_probe+0x18/0x88) from [<c01ab8f8>] (platform_drv_probe+0x18/0x1c)
[    5.772247] [<c01ab8f8>] (platform_drv_probe+0x18/0x1c) from [<c01aaa68>] (driver_probe_device+0x78/0x164)
[    5.772369] [<c01aaa68>] (driver_probe_device+0x78/0x164) from [<c01aabe0>] (__driver_attach+0x8c/0x90)
[    5.772460] [<c01aabe0>] (__driver_attach+0x8c/0x90) from [<c01a9d3c>] (bus_for_each_dev+0x50/0x7c)
[    5.772583] [<c01a9d3c>] (bus_for_each_dev+0x50/0x7c) from [<c01aa3e4>] (bus_add_driver+0x98/0x240)
[    5.772674] [<c01aa3e4>] (bus_add_driver+0x98/0x240) from [<c01aae1c>] (driver_register+0x78/0x13c)
[    5.772796] [<c01aae1c>] (driver_register+0x78/0x13c) from [<c00254d4>] (do_one_initcall+0x30/0x1a0)
[    5.772918] [<c00254d4>] (do_one_initcall+0x30/0x1a0) from [<c00089a4>] (kernel_init+0x98/0x114)
[    5.773010] [<c00089a4>] (kernel_init+0x98/0x114) from [<c002692c>] (kernel_thread_exit+0x0/0x8)
[    5.773101] ---[ end trace 1b75b31a2719ed1d ]---
[    5.773681] smd_init()
[    5.773742] smd_core_init()
[    5.773895] smd_core_init() done
[    5.773956] msm_init_last_radio_log: could not retrieve SMEM_CLKREGIM_BSP
[    5.774810] smem_find(16, 40): wrong size 16424
[    5.774902] smd_alloc_channel() cid=02 size=08192 'SMD_RPCCALL'
[    5.775360] smem_find(25, 40): wrong size 16424
[    5.775421] smd_alloc_channel() cid=11 size=08192 'SMD_DATA5'
[    5.775665] smem_find(26, 40): wrong size 16424
[    5.775726] smd_alloc_channel() cid=12 size=08192 'SMD_DATA6'
[    5.775970] smem_find(27, 40): wrong size 16424
[    5.776031] smd_alloc_channel() cid=13 size=08192 'SMD_DATA7'
[    5.776306] smem_find(31, 40): wrong size 16424
[    5.776367] smd_alloc_channel() cid=17 size=08192 'SMD_DATA11'
[    5.776550] smem_find(47, 40): wrong size 16424
[    5.776611] smd_alloc_channel() cid=33 size=08192 'SMD_CS_A2M'
[    5.776824] smem_find(52, 40): wrong size 16424
[    5.776885] smd_alloc_channel() cid=38 size=08192 'SMD_DATA5_CNTL'
[    5.777069] smem_find(53, 40): wrong size 16424
[    5.777130] smd_alloc_channel() cid=39 size=08192 'SMD_DATA6_CNTL'
[    5.777313] smem_find(54, 40): wrong size 16424
[    5.777374] smd_alloc_channel() cid=40 size=08192 'SMD_DATA7_CNTL'
[    5.779418] SMD: ch 2 1 -> 2
[    5.783355] mdp_probe: initialized
[    5.785430] H2W: Registering H2W (headset) driver
[    5.799560] RPC_TIME_TOD_SET_APPS_BASES:
[    5.799560] 	tick = 12641626
[    5.799560] 	stamp = 859059045
[    5.800476] input: h2w headset as /devices/virtual/input/input0
[    5.808807] ashmem: initialized
[    5.823394] yaffs Nov 30 2011 05:25:41 Installing. 
[    5.823608] msgmni has been set to 209
[    5.834533] adsp: probe
[    5.842407] alg: No test for stdrng (krng)
[    5.842926] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    5.843048] io scheduler noop registered
[    5.843078] io scheduler anticipatory registered (default)
[    5.843688] mddi: init() base=0xc70b8000 irq=16
[    5.905487] mddi cmd send rtd: int 3a000, stat 8063, rtd val e
[    5.905822] mddi: registering panel mddi_c_d263_0000
[    5.905975] mddi: publish: 
[    5.908264] vsync on gpio 97 now 0
[    5.957672] msmfb_probe() installing 320 x 480 panel
[    6.004882] msm_serial: detected port #0
[    6.005645] msm_serial.0: ttyMSM0 at MMIO 0xa9a00000 (irq = 9) is a MSM
[    6.007141] msm_serial: detected port #2
[    6.007568] msm_serial.2: ttyMSM2 at MMIO 0xa9c00000 (irq = 11) is a MSM
[    6.009338] msm_serial: driver initialized
[    6.010772] msm_serial_hs.0: ttyHS0 at MMIO 0xa0200000 (irq = 45) is a MSM HS UART
[    6.011718] msm_serial_hs module loaded
[    6.016784] loop: module loaded
[    6.016998] pmem: 1 init
[    6.017822] pmem_adsp: 0 init
[    6.018768] pmem_camera: 0 init
[    6.020629] msm_nand: allocated dma buffer at ffa0b000, dma_addr 16957000
[    6.021118] msm_nand: read CFG0 = aad400c0 CFG1 = 4745c
[    6.021179] msm_nand: CFG0 cw/page=3 ud_sz=512 ecc_sz=10 spare_sz=5
[    6.021362] msm_nand: NAND_READ_ID = 1500aaec
[    6.021545] msn_nand: nandid 1500aaec status c03120
[    6.021606] msm_nand: manuf Samsung (0xec) device 0xaa blocksz 20000 pagesz 800 size 10000000
[    6.021667] msm_nand: save CFG0 = e8d408c0 CFG1 = 4745c
[    6.021728] msm_nand: CFG0: cw/page=3 ud_sz=516 ecc_sz=10 spare_sz=1 num_addr_cycles=5
[    6.022521] msm_nand: DEV_CMD1: f00f3000
[    6.022735] msm_nand: NAND_EBI2_ECC_BUF_CFG: 1ff
[    6.022796] Creating 6 MTD partitions on "msm_nand":
[    6.022857] 0x0000024c0000-0x000002500000 : "misc"
[    6.024871] 0x0000026c0000-0x000002bc0000 : "recovery"
[    6.035705] 0x000002bc0000-0x000002e40000 : "boot"
[    6.043518] 0x000002e40000-0x000008840000 : "system"
[    6.243774] 0x000008840000-0x00000a640000 : "cache"
[    6.311767] 0x00000a640000-0x000010000000 : "userdata"
[    6.507385] tun: Universal TUN/TAP device driver, 1.6
[    6.507629] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    6.517303] msm72k_udc: msm72k_probe
[    6.517852] msm72k_udc: msm72k_probe() io=c70c8000, irq=47, dma=ffa0c000(1699c000)
[    6.519836] g_ether gadget: using random self ethernet address
[    6.520111] g_ether gadget: using random host ethernet address
[    6.522460] usb0: MAC 86:6c:b4:32:17:48
[    6.522644] usb0: HOST MAC 1a:44:f9:7a:5a:80
[    6.523834] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[    6.524078] g_ether gadget: g_ether ready
[    6.524261] msm72k_udc: msm72k_udc: registered gadget driver 'g_ether'
[    6.525726] mice: PS/2 mouse device common for all mice
[    6.527618] msm72k_udc: IDLE -> ONLINE
[    6.527893] hsusb: reset controller
[    6.566009] msm_hsusb_phy_reset: success
[    6.575836] msm_i2c msm_i2c.0: error, status 43c8
[    6.576019] msm_i2c msm_i2c.0: Error during data xfer (-5)
[    6.657501] trout_gpio_irq_handler: got masked interrupt: 0:80
[    6.685913] trout_gpio_irq_handler: got masked interrupt: 0:80
[    6.686157] synaptics_ts_probe: Product Major Version 1
[    6.687042] trout_gpio_irq_handler: got masked interrupt: 0:80
[    6.687255] synaptics_ts_probe: Product Minor Version c
[    6.688110] trout_gpio_irq_handler: got masked interrupt: 0:80
[    6.688385] synaptics_ts_probe: product property 2
[    6.689208] trout_gpio_irq_handler: got masked interrupt: 0:80
[    6.689422] synaptics_ts_probe: device control 81
[    6.690277] trout_gpio_irq_handler: got masked interrupt: 0:80
[    6.690490] synaptics_ts_probe: interrupt enable 3
[    6.692565] synaptics_ts_probe: 0xe0: 1 1 1 2 1 c 0 0
[    6.693847] synaptics_ts_probe: Sensor properties 601
[    6.697784] synaptics_ts_probe: max_x 3480, max_y 5368
[    6.697967] synaptics_ts_probe: inactive_x -80 -80, inactive_y -32 -32
[    6.698181] synaptics_ts_probe: snap_x 240-248 240-248, snap_y 80-88 80-88
[    6.699523] input: synaptics-rmi-touchscreen as /devices/virtual/input/input1
[    6.702148] synaptics_ts_probe: Start touchscreen synaptics-rmi-touchscreen in interrupt mode
[    6.703979] GPIO Input Driver: Start gpio inputs for trout-nav in interrupt mode
[    6.705780] input: trout-nav as /devices/virtual/input/input2
[    6.708801] GPIO Matrix Keypad Driver: Start keypad matrix for trout-keypad-v3 in interrupt mode
[    6.709655] GPIO Input Driver: Start gpio inputs for trout-keypad-v3 in interrupt mode
[    6.710266] GPIO Input Driver: Start gpio inputs for trout-keypad-v3 in interrupt mode
[    6.712066] input: trout-keypad-v3 as /devices/virtual/input/input3
[    6.715820] using input dev h2w headset for key reset
[    6.716156] using input dev trout-nav for key reset
[    6.716339] using input dev trout-keypad-v3 for key reset
[    6.718353] rs30000048:0da5b528 rs30000048:0da5b528: rtc core: registered msm_rtc as rtc0
[    6.718933] AKM8976A compass driver: init
[    6.719787] msm72k_udc: ulpi: write 0x40 to 0x31
[    6.720031] msm72k_udc: ulpi: write 0x1d to 0x0d
[    6.720153] msm72k_udc: ulpi: write 0x1d to 0x10
[    6.720336] msm72k_udc: ept #0 out max:64 head:ffa0c000 bit:0
[    6.720489] msm72k_udc: ept #1 out max:512 head:ffa0c080 bit:1
[    6.720672] msm72k_udc: ept #2 out max:512 head:ffa0c100 bit:2
[    6.720855] msm72k_udc: ept #3 out max:512 head:ffa0c180 bit:3
[    6.721038] msm72k_udc: ept #4 out max:512 head:ffa0c200 bit:4
[    6.721191] msm72k_udc: ept #5 out max:512 head:ffa0c280 bit:5
[    6.721374] msm72k_udc: ept #6 out max:512 head:ffa0c300 bit:6
[    6.721557] msm72k_udc: ept #7 out max:512 head:ffa0c380 bit:7
[    6.721740] msm72k_udc: ept #8 out max:512 head:ffa0c400 bit:8
[    6.721893] msm72k_udc: ept #9 out max:512 head:ffa0c480 bit:9
[    6.722076] msm72k_udc: ept #10 out max:512 head:ffa0c500 bit:10
[    6.722259] msm72k_udc: ept #11 out max:512 head:ffa0c580 bit:11
[    6.722442] msm72k_udc: ept #12 out max:512 head:ffa0c600 bit:12
[    6.722625] msm72k_udc: ept #13 out max:512 head:ffa0c680 bit:13
[    6.722778] msm72k_udc: ept #14 out max:512 head:ffa0c700 bit:14
[    6.722961] msm72k_udc: ept #15 out max:512 head:ffa0c780 bit:15
[    6.723144] msm72k_udc: ept #0 in max:64 head:ffa0c040 bit:16
[    6.723327] msm72k_udc: ept #1 in max:512 head:ffa0c0c0 bit:17
[    6.723480] msm72k_udc: ept #2 in max:512 head:ffa0c140 bit:18
[    6.723663] msm72k_udc: ept #3 in max:512 head:ffa0c1c0 bit:19
[    6.723846] msm72k_udc: ept #4 in max:512 head:ffa0c240 bit:20
[    6.724029] msm72k_udc: ept #5 in max:512 head:ffa0c2c0 bit:21
[    6.724182] msm72k_udc: ept #6 in max:512 head:ffa0c340 bit:22
[    6.724365] msm72k_udc: ept #7 in max:512 head:ffa0c3c0 bit:23
[    6.724548] msm72k_udc: ept #8 in max:512 head:ffa0c440 bit:24
[    6.724700] msm72k_udc: ept #9 in max:512 head:ffa0c4c0 bit:25
[    6.724884] msm72k_udc: ept #10 in max:512 head:ffa0c540 bit:26
[    6.725311] msm72k_udc: ept #11 in max:512 head:ffa0c5c0 bit:27
[    6.725524] msm72k_udc: ept #12 in max:512 head:ffa0c640 bit:28
[    6.725708] msm72k_udc: ept #13 in max:512 head:ffa0c6c0 bit:29
[    6.725860] msm72k_udc: ept #14 in max:512 head:ffa0c740 bit:30
[    6.726043] msm72k_udc: ept #15 in max:512 head:ffa0c7c0 bit:31
[    6.726257] usb: notify offline
[    6.726348] msm_hsusb: enable pullup
[    6.726470] msm72k_udc: ONLINE -> OFFLINE
[    6.726593] msm_hsusb: disable pullup
[    6.726745] usb: notify offline
[    6.747100] input: compass as /devices/virtual/input/input4
[    6.749572] msm_hsusb_phy_reset: success
[    6.749786] smem_find(41, 40): wrong size 16424
[    6.749847] smd_alloc_channel() cid=27 size=08192 'SMD_GPSNMEA'
[    6.753692] Registered led device: blue
[    6.753906] Registered led device: green
[    6.754089] Registered led device: red
[    6.755767] device-mapper: uevent: version 1.0.3
[    6.757324] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    6.757934] Bluetooth: HCI UART driver ver 2.2
[    6.758026] Bluetooth: HCI H4 protocol initialized
[    6.758056] Bluetooth: HCI BCSP protocol initialized
[    6.758117] Bluetooth: HCILL protocol initialized
[    6.758728] sdhci: Secure Digital Host Controller Interface driver
[    6.758819] sdhci: Copyright(c) Pierre Ossman
[    6.760162] mmc0: Qualcomm MSM SDCC at 0x00000000a0400000 irq 24,0 dma 8
[    6.760284] mmc0: 4 bit data mode enabled
[    6.760314] mmc0: MMC clock 144000 -> 50000000 Hz, PCLK 64000000 Hz
[    6.760375] mmc0: Slot eject status = 1
[    6.760406] mmc0: Power save feature enable = 1
[    6.760437] mmc0: DM non-cached buffer at ffa0e000, dma_addr 0x169b9000
[    6.760498] mmc0: DM cmd busaddr 0x169b9000, cmdptr busaddr 0x169b9300
[    6.761535] trout_sdslot_switchvdd: Disabling SD slot power
[    6.761932] mmc1: Qualcomm MSM SDCC at 0x00000000a0500000 irq 26,194 dma 8
[    6.761993] mmc1: 4 bit data mode enabled
[    6.762023] mmc1: MMC clock 144000 -> 50000000 Hz, PCLK 64000000 Hz
[    6.762054] mmc1: Slot eject status = 0
[    6.762084] mmc1: Power save feature enable = 1
[    6.762145] mmc1: DM non-cached buffer at ffa0f000, dma_addr 0x169bb000
[    6.762176] mmc1: DM cmd busaddr 0x169bb000, cmdptr busaddr 0x169bb300
[    6.762786] Registered led device: spotlight
[    6.763061] Registered led device: keyboard-backlight
[    6.763275] Registered led device: button-backlight
[    6.764495] wacom driver registered
[    6.765625] Advanced Linux Sound Architecture Driver Version 1.0.21.
[    6.767089] No device for DAI CODEC_DAI
[    6.767181] No device for DAI CPU_DAI
[    6.767242] msm_soc: create pcms
[    6.767700] asoc: CODEC_DAI <-> CPU_DAI mapping ok
[    6.767761] msm_soc:ALSA MSM Mixer Setting
[    6.771148] ALSA device list:
[    6.771270]   #0: msm-audio (MSM-CARD)
[    6.772003] TCP cubic registered
[    6.773803] NET: Registered protocol family 10
[    6.775238] lo: Disabled Privacy Extensions
[    6.777038] Mobile IPv6
[    6.777130] IPv6 over IPv4 tunneling driver
[    6.778167] sit0: Disabled Privacy Extensions
[    6.779418] ip6tnl0: Disabled Privacy Extensions
[    6.779785] NET: Registered protocol family 17
[    6.779937] NET: Registered protocol family 15
[    6.780029] Bluetooth: L2CAP ver 2.14
[    6.780090] Bluetooth: L2CAP socket layer initialized
[    6.780151] Bluetooth: SCO (Voice Link) ver 0.6
[    6.780181] Bluetooth: SCO socket layer initialized
[    6.780670] Bluetooth: RFCOMM TTY layer initialized
[    6.780761] Bluetooth: RFCOMM socket layer initialized
[    6.780822] Bluetooth: RFCOMM ver 1.11
[    6.780853] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    6.780883] Bluetooth: BNEP filters: protocol multicast
[    6.780944] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    6.781616] clock_late_init() disabled 18 unused clocks
[    6.784393] rs30000048:0da5b528 rs30000048:0da5b528: setting system clock to 2011-12-02 19:16:07 UTC (1322853367)
[    6.784637] Waiting 8sec before mounting root device...
[    6.815216] smem_find(14, 40): wrong size 16424
[    6.815368] smd_alloc_channel() cid=00 size=08192 'SMD_DS'
[    6.816162] smem_find(21, 40): wrong size 16424
[    6.816314] smd_alloc_channel() cid=07 size=08192 'SMD_DATA1'
[    6.816864] smem_find(22, 40): wrong size 16424
[    6.816986] smd_alloc_channel() cid=08 size=08192 'SMD_DATA2'
[    6.817535] smem_find(23, 40): wrong size 16424
[    6.817657] smd_alloc_channel() cid=09 size=08192 'SMD_DATA3'
[    6.818115] smem_find(24, 40): wrong size 16424
[    6.818206] smd_alloc_channel() cid=10 size=08192 'SMD_DATA4'
[    6.822174] trout_sdslot_switchvdd: Setting level to 2950
[    6.865722] msmfb_start_dma 20.507 ms after vsync request
[    6.886077] trout_sdslot_switchvdd: Setting level to 2750
[    7.264617] mmc1: host does not support reading read-only switch. assuming write-enable.
[    7.264953] mmc1: new high speed SDHC card at address b368
[    7.266693] mmcblk0: mmc1:b368 USD   3.75 GiB 
[    7.267883]  mmcblk0: p1
[   14.794342] EXT3-fs: mounted filesystem with writeback data mode.
[   14.794738] VFS: Mounted root (ext3 filesystem) readonly on device 179:1.
[   14.795715] kjournald starting.  Commit interval 5 seconds
[   14.798522] devtmpfs: mounted
[   14.798919] Freeing init memory: 116K
[   15.465820] EXT3 FS on mmcblk0p1, internal journal
[   20.885742] msm72k_udc: OFFLINE -> ONLINE
[   20.886016] hsusb: reset controller
[   20.949157] msm_hsusb_phy_reset: success
[   21.095245] msm72k_udc: ulpi: write 0x40 to 0x31
[   21.095336] msm72k_udc: ulpi: write 0x1d to 0x0d
[   21.095397] msm72k_udc: ulpi: write 0x1d to 0x10
[   21.095428] msm72k_udc: ept #0 out max:64 head:ffa0c000 bit:0
[   21.095489] msm72k_udc: ept #1 out max:512 head:ffa0c080 bit:1
[   21.095550] msm72k_udc: ept #2 out max:512 head:ffa0c100 bit:2
[   21.095581] msm72k_udc: ept #3 out max:512 head:ffa0c180 bit:3
[   21.095642] msm72k_udc: ept #4 out max:512 head:ffa0c200 bit:4
[   21.095672] msm72k_udc: ept #5 out max:512 head:ffa0c280 bit:5
[   21.095733] msm72k_udc: ept #6 out max:512 head:ffa0c300 bit:6
[   21.095764] msm72k_udc: ept #7 out max:512 head:ffa0c380 bit:7
[   21.095794] msm72k_udc: ept #8 out max:512 head:ffa0c400 bit:8
[   21.095855] msm72k_udc: ept #9 out max:512 head:ffa0c480 bit:9
[   21.095886] msm72k_udc: ept #10 out max:512 head:ffa0c500 bit:10
[   21.095916] msm72k_udc: ept #11 out max:512 head:ffa0c580 bit:11
[   21.095977] msm72k_udc: ept #12 out max:512 head:ffa0c600 bit:12
[   21.096008] msm72k_udc: ept #13 out max:512 head:ffa0c680 bit:13
[   21.096069] msm72k_udc: ept #14 out max:512 head:ffa0c700 bit:14
[   21.096099] msm72k_udc: ept #15 out max:512 head:ffa0c780 bit:15
[   21.096130] msm72k_udc: ept #0 in max:64 head:ffa0c040 bit:16
[   21.096191] msm72k_udc: ept #1 in max:512 head:ffa0c0c0 bit:17
[   21.096221] msm72k_udc: ept #2 in max:512 head:ffa0c140 bit:18
[   21.096282] msm72k_udc: ept #3 in max:512 head:ffa0c1c0 bit:19
[   21.096313] msm72k_udc: ept #4 in max:512 head:ffa0c240 bit:20
[   21.096343] msm72k_udc: ept #5 in max:512 head:ffa0c2c0 bit:21
[   21.096405] msm72k_udc: ept #6 in max:512 head:ffa0c340 bit:22
[   21.096435] msm72k_udc: ept #7 in max:512 head:ffa0c3c0 bit:23
[   21.096466] msm72k_udc: ept #8 in max:512 head:ffa0c440 bit:24
[   21.096527] msm72k_udc: ept #9 in max:512 head:ffa0c4c0 bit:25
[   21.096557] msm72k_udc: ept #10 in max:512 head:ffa0c540 bit:26
[   21.096618] msm72k_udc: ept #11 in max:512 head:ffa0c5c0 bit:27
[   21.096649] msm72k_udc: ept #12 in max:512 head:ffa0c640 bit:28
[   21.096679] msm72k_udc: ept #13 in max:512 head:ffa0c6c0 bit:29
[   21.096740] msm72k_udc: ept #14 in max:512 head:ffa0c740 bit:30
[   21.096771] msm72k_udc: ept #15 in max:512 head:ffa0c7c0 bit:31
[   21.096832] usb: notify offline
[   21.096862] msm_hsusb: enable pullup
[   21.099945] msm72k_udc: msm72k_udc: suspend
[   21.201904] msm72k_udc: msm72k_udc: reset
[   21.204223] msm72k_udc: msm72k_udc: portchange USB_SPEED_HIGH
[   21.306976] msm72k_udc: msm72k_udc: reset
[   21.309295] msm72k_udc: msm72k_udc: portchange USB_SPEED_HIGH
[   21.437622] g_ether gadget: high speed config #1: CDC Ethernet (ECM)
[   21.437744] msm72k_udc: ept #2 in max:64 head:ffa0c140 bit:18
[   21.440521] msm72k_udc: ept #1 in max:512 head:ffa0c0c0 bit:17
[   21.440643] msm72k_udc: ept #1 out max:512 head:ffa0c080 bit:1
[   25.525268] cfg80211: Calling CRDA to update world regulatory domain
[   36.945068] usb0: no IPv6 routers present


USER       PID %CPU %MEM    VSZ   RSS TTY      STAT START   TIME COMMAND
root         1  0.3  0.5   1408   568 ?        Ss   19:16   0:00 init [5]  
root         2  0.0  0.0      0     0 ?        S    19:16   0:00 [kthreadd]
root         3  0.0  0.0      0     0 ?        S    19:16   0:00 [ksoftirqd/0]
root         4  0.0  0.0      0     0 ?        S    19:16   0:00 [events/0]
root         5  0.0  0.0      0     0 ?        S    19:16   0:00 [khelper]
root         6  0.0  0.0      0     0 ?        S    19:16   0:00 [async/mgr]
root         7  0.0  0.0      0     0 ?        S    19:16   0:00 [suspend]
root         8  0.0  0.0      0     0 ?        S    19:16   0:00 [sync_supers]
root         9  0.0  0.0      0     0 ?        S    19:16   0:00 [bdi-default]
root        10  0.0  0.0      0     0 ?        S    19:16   0:00 [kblockd/0]
root        11  0.0  0.0      0     0 ?        S    19:16   0:00 [kseriod]
root        12  0.0  0.0      0     0 ?        S    19:16   0:00 [kmmcd]
root        13  0.0  0.0      0     0 ?        S    19:16   0:00 [bluetooth]
root        14  0.0  0.0      0     0 ?        S    19:16   0:00 [kondemand/0]
root        15  0.0  0.0      0     0 ?        S    19:16   0:00 [qmi]
root        16  0.0  0.0      0     0 ?        D    19:16   0:00 [rpcrouter]
root        17  0.0  0.0      0     0 ?        S    19:16   0:00 [detection/0]
root        18  0.0  0.0      0     0 ?        S    19:16   0:00 [krpcserversd]
root        19  0.0  0.0      0     0 ?        S    19:16   0:00 [kswapd0]
root        20  0.0  0.0      0     0 ?        S    19:16   0:00 [aio/0]
root        21  0.0  0.0      0     0 ?        S    19:16   0:00 [crypto/0]
root        30  0.0  0.0      0     0 ?        S    19:16   0:00 [kadspd]
root        32  0.0  0.0      0     0 ?        S    19:16   0:00 [panel_on/0]
root        33  0.0  0.0      0     0 ?        D    19:16   0:00 [msmfb_refreshd]
root        34  0.0  0.0      0     0 ?        S    19:16   0:00 [msm_serial_hs]
root        35  0.0  0.0      0     0 ?        S    19:16   0:00 [mtdblockd]
root        36  0.0  0.0      0     0 ?        S    19:16   0:00 [rmnet/0]
root        37  0.0  0.0      0     0 ?        S    19:16   0:00 [synaptics_wq]
root        38  0.0  0.0      0     0 ?        S    19:16   0:00 [kstriped]
root        39  0.0  0.0      0     0 ?        S    19:16   0:00 [kconservative/0]
root        40  0.0  0.0      0     0 ?        S<   19:16   0:00 [krfcommd]
root        41  2.5  0.0      0     0 ?        S    19:16   0:02 [mmcqd]
root        42  0.2  0.0      0     0 ?        S    19:16   0:00 [kjournald]
root        80  0.0  0.0      0     0 ?        S    19:16   0:00 [flush-179:0]
root        81  0.5  0.6   1812   676 ?        S<s  19:16   0:00 /sbin/udevd -d
root       156  0.0  0.6   1808   672 ?        S<   19:16   0:00 /sbin/udevd -d
root       159  0.0  0.5   1808   620 ?        S<   19:16   0:00 /sbin/udevd -d
44         593  0.3  0.8   2296   888 ?        Ss   19:16   0:00 /usr/bin/dbus-daemon --system
root       603  0.0  0.7   3664   836 ?        Ss   19:17   0:00 /usr/sbin/sshd
nobody     607  0.0  0.5   2104   640 ?        S    19:17   0:00 /usr/bin/dnsmasq -7 /etc/dnsmasq.d
root       610  0.1  0.6   2712   692 ?        Ss   19:17   0:00 /sbin/syslogd -n -C64 -m 20
root       612  0.1  0.5   2648   596 ?        Ss   19:17   0:00 /sbin/klogd -n
root       615 39.4 11.7  25812 12624 ?        Ss   19:17   0:21 python /usr/bin/frameworkd
root       618  0.1  1.4   3808  1540 ?        Ss   19:17   0:00 /usr/sbin/fso-gpsd -S localhost gpsd -P /var/run/fso-gpsd.pid
root       628  0.0  0.4   1660   528 tty1     Ss+  19:17   0:00 /sbin/getty 38400 tty1
root       631  2.5  2.9  15488  3204 ?        Sl   19:17   0:00 /usr/sbin/fsousaged
root       633  3.3  1.6   3748  1800 ?        Ss   19:17   0:00 sshd: root@pts/0 
root       635  1.4  0.7   2824   824 pts/0    Ss   19:17   0:00 -sh
root       637  0.0  0.8   2064   888 pts/0    R+   19:18   0:00 ps aux

Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.0.0     0.0.0.0         255.255.255.0   U     0      0        0 usb0
0.0.0.0         192.168.0.200   0.0.0.0         UG    8      0        0 usb0


2011.12.02 19:17:11.199 root                 INFO     Installprefix is /usr
2011.12.02 19:17:11.215 root                 INFO     Etc directory is /etc/freesmartphone
2011.12.02 19:17:14.006 frameworkd.subsystem INFO     subsystem frameworkd took 0.88 seconds to startup
2011.12.02 19:17:14.058 frameworkd.controller INFO     skipping subsystem ogsmd as requested via config file.
2011.12.02 19:17:14.066 frameworkd.controller INFO     skipping subsystem onetworkd as requested via config file.
2011.12.02 19:17:14.075 frameworkd.controller INFO     launching internal subsystem testing
2011.12.02 19:17:14.105 frameworkd.subsystem INFO     Scanned subsystem via method 'auto', result is ['__init__.py', 'testing.py', 'testing.pyo', '__init__.pyo']
2011.12.02 19:17:14.544 testing              INFO     Resource 0.0.0 at /org/freesmartphone/Testing initialized.
2011.12.02 19:17:14.552 frameworkd.subsystem INFO     subsystem testing took 0.47 seconds to startup
2011.12.02 19:17:14.560 frameworkd.controller INFO     skipping subsystem ophoned as requested via config file.
2011.12.02 19:17:14.568 frameworkd.controller INFO     skipping subsystem odeviced as requested via config file.
2011.12.02 19:17:14.578 frameworkd.controller INFO     launching internal subsystem opreferencesd
2011.12.02 19:17:14.608 frameworkd.subsystem INFO     Scanned subsystem via method 'auto', result is ['__init__.py', 'helpers.py', 'configuration.py', 'service.py', 'configuration.pyo', 'schema.pyo', 'opreferences.pyo', 'opreferences.py', 'service.pyo', 'helpers.pyo', '__init__.pyo', 'schema.py']
2011.12.02 19:17:21.363 opreferencesd        INFO     PreferencesManager 0.2.0 initialized. Serving org.freesmartphone.Preferences at /org/freesmartphone/Preferences
2011.12.02 19:17:21.369 opreferencesd        INFO      ::: using schema path : /etc/freesmartphone/opreferences/schema
2011.12.02 19:17:21.374 opreferencesd        INFO      ::: using conf path : /etc/freesmartphone/opreferences/conf
2011.12.02 19:17:21.387 opreferencesd        INFO      ::: services : ['phone', 'rules', 'profiles']
2011.12.02 19:17:21.399 frameworkd.subsystem INFO     subsystem opreferencesd took 6.81 seconds to startup
2011.12.02 19:17:21.408 frameworkd.controller INFO     launching internal subsystem oeventsd
2011.12.02 19:17:21.439 frameworkd.subsystem INFO     Scanned subsystem via method 'auto', result is ['fso_actions.py', '__init__.py', 'parser.pyo', 'leds_actions.pyo', 'filter.pyo', 'rule.pyo', 'action.py', 'fso_triggers.py', 'fso_triggers.pyo', 'oevents.py', 'trigger.py', 'leds_actions.py', 'action.pyo', 'filter.py', 'fso_actions.pyo', 'oevents.pyo', 'rule.py', 'parser.py', 'trigger.pyo', '__init__.pyo']
2011.12.02 19:17:25.335 oeventsd             INFO     EventsManager 0.3.1 initialized. Serving org.freesmartphone.Events at /org/freesmartphone/Events
2011.12.02 19:17:25.584 oeventsd             INFO     Created new rule : on IncomingMessage if And() then MessageToneAction()
2011.12.02 19:17:25.651 oeventsd             INFO     Created new rule : While CallListContains(INCOMING) if ~(CallListContains(ACTIVE)) then [RingToneAction(), CommandAction(xset -display localhost:0 s reset, {}), SetLed(green, blink), OccupyResource(Display)]
2011.12.02 19:17:25.693 oeventsd             INFO     Created new rule : While CallStatus if Or(status == OUTGOING,status == ACTIVE) then [OccupyResource(CPU)]
2011.12.02 19:17:25.772 oeventsd             INFO     Created new rule : While CallStatus if And(Or(Or(status == OUTGOING,status == ACTIVE),And(status == INCOMING,CallListContains(ACTIVE))),BTHeadsetIsConnected()) then [SetScenario(gsmbluetooth), BTHeadsetPlaying()]
2011.12.02 19:17:25.805 oeventsd             INFO     Created new rule : While PowerStatus if status == charging then SetLed(blue, light)
2011.12.02 19:17:25.833 oeventsd             INFO     Created new rule : While PowerStatus if ~(status == discharging) then OccupyResource(CPU)
2011.12.02 19:17:25.861 oeventsd             INFO     Created new rule : While PowerStatus if status == critical then SetLed(red, blink)
2011.12.02 19:17:25.888 oeventsd             INFO     Created new rule : While PowerStatus if status == full then SetLed(green, light)
2011.12.02 19:17:25.911 oeventsd             INFO     Created new rule : on PowerStatus if status == empty then CommandAction(poweroff, {})
2011.12.02 19:17:25.943 oeventsd             INFO     Created new rule : on InputTrigger if And(switch == HEADSET,event == pressed) then CommandAction(amixer -d sset "Amp Spk" mute, {})
2011.12.02 19:17:25.977 oeventsd             INFO     Created new rule : on InputTrigger if And(switch == HEADSET,event == released) then CommandAction(amixer -d sset "Amp Spk" unmute, {})
2011.12.02 19:17:26.029 oeventsd             INFO     Created new rule : While IdleState if status == busy then [SetLed(lcd_backlight, light), SetLed(button_backlight, light), SetLed(keyboard_backlight, light)]
2011.12.02 19:17:26.058 oeventsd             INFO     Created new rule : on IdleState if status == idle_dim then [CommandAction(xset -display localhost:0 s blank, {}), CommandAction(xset -display localhost:0 s activate, {})]
2011.12.02 19:17:26.078 oeventsd             INFO     Created new rule : on IdleState if status == suspend then Suspend(())
2011.12.02 19:17:26.138 oeventsd             INFO     Created new rule : on InputTrigger if And(switch == LID,event == pressed) then [SetLed(keyboard_backlight, light), SetLed(button_backlight, light), SetLed(lcd_backlight, light), Debug("Lid Opened")]
2011.12.02 19:17:26.167 frameworkd.subsystem INFO     subsystem oeventsd took 4.75 seconds to startup
2011.12.02 19:17:26.175 frameworkd.controller INFO     skipping subsystem ousaged as requested via config file.
2011.12.02 19:17:26.184 frameworkd.controller INFO     launching internal subsystem opimd
2011.12.02 19:17:26.215 frameworkd.subsystem INFO     Scanned subsystem via method 'auto', result is ['opimd.pyo', 'pimd_notes.pyo', '__init__.py', 'db_upgrade.pyo', 'query_manager.py', 'query_manager.pyo', 'helpers.py', 'domain_manager.py', 'pimd_messages.py', 'pimd_dates.py', 'pimd_dates.pyo', 'pimd_calls.py', 'type_manager.py', 'domain_manager.pyo', 'pimd_tasks.pyo', 'type_manager.pyo', 'pimd_messages.pyo', 'pimd_tasks.py', 'pimd_generic.py', 'pimd_contacts.pyo', 'pimd_calls.pyo', 'db_handler.py', 'helpers.pyo', 'pimd_notes.py', 'db', 'db_upgrade.py', 'opimd.py', 'pimd_generic.pyo', 'db_handler.pyo', 'pimd_contacts.py', '__init__.pyo']
2011.12.02 19:17:30.338 opimd                INFO     Registered domain Contacts
2011.12.02 19:17:32.182 opimd                INFO     Registered domain Calls
2011.12.02 19:17:33.302 opimd                INFO     Registered domain Dates
2011.12.02 19:17:34.484 opimd                INFO     Registered domain Notes
2011.12.02 19:17:35.580 opimd                INFO     Registered domain Tasks
2011.12.02 19:17:37.396 opimd                INFO     FSO-Messages-Handler: Installed signal handlers
2011.12.02 19:17:37.411 opimd                INFO     Registered domain Messages
2011.12.02 19:17:37.465 frameworkd.subsystem INFO     subsystem opimd took 11.27 seconds to startup
2011.12.02 19:17:37.475 frameworkd.controller INFO     launching internal subsystem ogpsd
2011.12.02 19:17:37.506 frameworkd.subsystem INFO     Scanned subsystem via method 'auto', result is ['__init__.py', 'eten.pyo', 'msm.py', 'gpschannel.pyo', 'helpers.py', 'gpsdevice.py', 'om.py', 'eten.py', 'ubx.py', 'om.pyo', 'msm.pyo', 'nmea.py', 'nmea.pyo', 'ubx.pyo', 'helpers.pyo', 'factory.py', 'gpschannel.py', 'factory.pyo', '__init__.pyo', 'gpsdevice.pyo']
2011.12.02 19:17:39.001 ogpsd.gpsdevice      INFO     MSMDevice initialized. Serving org.freedesktop.Gypsy at /org/freedesktop/Gypsy
2011.12.02 19:17:39.014 frameworkd.subsystem INFO     subsystem ogpsd took 1.53 seconds to startup
2011.12.02 19:17:39.023 frameworkd.controller INFO     skipping subsystem otimed as requested via config file.
2011.12.02 19:17:39.052 dbus.proxies         ERROR    Introspect error on org.freesmartphone.ogsmd:/org/freesmartphone/GSM/Device: dbus.exceptions.DBusException: org.freedesktop.DBus.Error.ServiceUnknown: The name org.freesmartphone.ogsmd was not provided by any .service files
2011.12.02 19:17:39.075 frameworkd.controller INFO     ================== mainloop   entered ===================
2011.12.02 19:17:39.081 frameworkd.controller INFO     startup time was 26.02 seconds
2011.12.02 19:17:39.842 oeventsd             INFO     Updating the rules
2011.12.02 19:17:39.848 opreferencesd        INFO     GetService rules
2011.12.02 19:17:40.045 oeventsd.rule        INFO     enable rule : on IncomingMessage if And() then MessageToneAction()
2011.12.02 19:17:40.059 oeventsd.rule        INFO     enable rule : While CallListContains(INCOMING) if ~(CallListContains(ACTIVE)) then [RingToneAction(), CommandAction(xset -display localhost:0 s reset, {}), SetLed(green, blink), OccupyResource(Display)]
2011.12.02 19:17:40.066 oeventsd.rule        INFO     enable rule : CallListContains(INCOMING)
2011.12.02 19:17:40.079 oeventsd.rule        INFO     enable rule : CallListContains(ACTIVE)
2011.12.02 19:17:40.091 oeventsd.rule        INFO     enable rule : While CallStatus if Or(status == OUTGOING,status == ACTIVE) then [OccupyResource(CPU)]
2011.12.02 19:17:40.106 oeventsd.rule        INFO     enable rule : While CallStatus if And(Or(Or(status == OUTGOING,status == ACTIVE),And(status == INCOMING,CallListContains(ACTIVE))),BTHeadsetIsConnected()) then [SetScenario(gsmbluetooth), BTHeadsetPlaying()]
2011.12.02 19:17:40.123 oeventsd.rule        INFO     enable rule : CallListContains(ACTIVE)
2011.12.02 19:17:40.135 oeventsd.rule        INFO     enable rule : BTHeadsetIsConnected()
2011.12.02 19:17:40.148 oeventsd.rule        INFO     enable rule : While PowerStatus if status == charging then SetLed(blue, light)
2011.12.02 19:17:40.161 oeventsd.rule        INFO     enable rule : While PowerStatus if ~(status == discharging) then OccupyResource(CPU)
2011.12.02 19:17:40.174 oeventsd.rule        INFO     enable rule : While PowerStatus if status == critical then SetLed(red, blink)
2011.12.02 19:17:40.188 oeventsd.rule        INFO     enable rule : While PowerStatus if status == full then SetLed(green, light)
2011.12.02 19:17:40.201 oeventsd.rule        INFO     enable rule : on PowerStatus if status == empty then CommandAction(poweroff, {})
2011.12.02 19:17:40.214 oeventsd.rule        INFO     enable rule : on InputTrigger if And(switch == HEADSET,event == pressed) then CommandAction(amixer -d sset "Amp Spk" mute, {})
2011.12.02 19:17:40.228 oeventsd.rule        INFO     enable rule : on InputTrigger if And(switch == HEADSET,event == released) then CommandAction(amixer -d sset "Amp Spk" unmute, {})
2011.12.02 19:17:40.243 oeventsd.rule        INFO     enable rule : While IdleState if status == busy then [SetLed(lcd_backlight, light), SetLed(button_backlight, light), SetLed(keyboard_backlight, light)]
2011.12.02 19:17:40.257 oeventsd.rule        INFO     enable rule : on IdleState if status == idle_dim then [CommandAction(xset -display localhost:0 s blank, {}), CommandAction(xset -display localhost:0 s activate, {})]
2011.12.02 19:17:40.270 oeventsd.rule        INFO     enable rule : on IdleState if status == suspend then Suspend(())
2011.12.02 19:17:40.283 oeventsd.rule        INFO     enable rule : on InputTrigger if And(switch == LID,event == pressed) then [SetLed(keyboard_backlight, light), SetLed(button_backlight, light), SetLed(lcd_backlight, light), Debug("Lid Opened")]
2011.12.02 19:17:40.441 opreferencesd        INFO     GetService phone
2011.12.02 19:17:41.614 opreferencesd        INFO     GetService phone
2011.12.02 19:17:42.428 opreferencesd        INFO     Service phone : can't find key message-length, using default
2011.12.02 19:17:42.441 opreferencesd        INFO     Service phone : can't find key ring-length, using default
2011.12.02 19:17:42.512 frameworkd.resource  INFO     setting resource status for TEST from unknown to disabling
2011.12.02 19:17:42.518 testing              INFO     disabling
2011.12.02 19:17:47.541 frameworkd.resource  INFO     setting resource status for TEST from disabling to disabled
2011.12.02 19:17:47.565 frameworkd.resource  INFO     setting resource status for GPS from unknown to disabling
2011.12.02 19:17:47.580 ogpsd.gpsdevice      INFO     disabling
2011.12.02 19:17:47.587 frameworkd.resource  INFO     setting resource status for GPS from disabling to disabled

2011-12-02T19:17:39.405975Z [INFO]  fsousaged : Binary launched successful (FsoFrameworkFileLogger created as theLogger)
2011-12-02T19:17:39.725036Z [INFO]  LowLevelKernel26 <>: Registering kernel26 low level suspend/resume handling
2011-12-02T19:17:39.726226Z [INFO]  UsageController <0 R>: Ready. Using lowlevel plugin kernel26 to handle suspend/resume
2011-12-02T19:17:39.727050Z [INFO]  fsousaged : loaded 3 plugins
2011-12-02T19:17:39.727294Z [INFO]  fsousaged : fsousaged => mainloop
2011-12-02T19:17:42.314209Z [ERROR] fsousaged : Can't sync dependencies of resource 'TEST': GDBus.Error:org.freedesktop.DBus.Error.UnknownMethod: Traceback (most recent call last):
  File "/usr/lib/python2.6/site-packages/dbus/service.py", line 649, in _message_cb
    (candidate_method, parent_method) = _method_lookup(self, method_name, interface_name)
  File "/usr/lib/python2.6/site-packages/dbus/service.py", line 244, in _method_lookup
    raise UnknownMethodException('%s is not a valid method of interface %s' % (method_name, dbus_interface))
UnknownMethodException: org.freedesktop.DBus.Error.UnknownMethod: Unknown method: GetDependencies is not a valid method of interface org.freesmartphone.Resource

2011-12-02T19:17:42.351532Z [ERROR] fsousaged : Can't sync dependencies of resource 'GPS': GDBus.Error:org.freedesktop.DBus.Error.UnknownMethod: Traceback (most recent call last):
  File "/usr/lib/python2.6/site-packages/dbus/service.py", line 649, in _message_cb
    (candidate_method, parent_method) = _method_lookup(self, method_name, interface_name)
  File "/usr/lib/python2.6/site-packages/dbus/service.py", line 244, in _method_lookup
    raise UnknownMethodException('%s is not a valid method of interface %s' % (method_name, dbus_interface))
UnknownMethodException: org.freedesktop.DBus.Error.UnknownMethod: Unknown method: GetDependencies is not a valid method of interface org.freesmartphone.Resource

Re: fso-console-image problems

[Denis 'GNUtoo' Carikli]

>When I boot up the console-image things are almost exactly the same - 
If you don't need Xorg,Try recompiling the kernel with the framebuffer console 
built in.

Denis.

Re: fso-console-image problems

[Mr Dash Four]

> If you don't need Xorg,Try recompiling the kernel with the framebuffer console 
> built in.
>   
I use bitbake to compile/build everything - how do I get that done there 
(I presume there must be some sort of .config file somewhere)?

Re: fso-console-image problems

[Mr Dash Four]

 
> I use bitbake to compile/build everything - how do I get that done 
> there (I presume there must be some sort of .config file somewhere)?
Right, after a bit of digging, I found this in my 
recipes/linux/linux-leviathan/defconfig (I think that's the kernel used 
to build my htcdream image, if not, then I'm wrong!):

# CONFIG_DISPLAY_SUPPORT is not set
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE is not set

Apart from setting "CONFIG_FRAMEBUFFER_CONSOLE=y" (and possibly setting 
"# CONFIG_DUMMY_CONSOLE is not set") should I activate anything else 
from the above? Is that all what's needed?

Re: fso-console-image problems

[Denis 'GNUtoo' Carikli]

>Apart from setting "CONFIG_FRAMEBUFFER_CONSOLE=y" (and possibly setting 
>"# CONFIG_DUMMY_CONSOLE is not set") should I activate anything else 
>from the above? Is that all what's needed?
Instead of trying to edit the file manually, try "make xconfig" in the 
directory where the kernel is extracted(something like work/htcdream*/linux-
leviathan*/git/ ) and do it manually trough the GUI, then save back the 
resulting defconfig, increase PR in the recipe and rebuild your console-image.

Denis.

Re: fso-console-image problems

[Mr Dash Four]

> Instead of trying to edit the file manually, try "make xconfig" in the 
> directory where the kernel is extracted(something like work/htcdream*/linux-
> leviathan*/git/ ) and do it manually trough the GUI, then save back the 
> resulting defconfig, increase PR in the recipe and rebuild your console-image.
>   
That as a very good advice, thank you! The versioning "magic" is 
something I didn't know about (I always used to delete all related files 
in the tmp/stamp directory in the futile hope that the process/steps 
will be repeated at the next run).

OK, since I use rm_work, the git directory is no longer there, but I've 
had the git tar archive, so unpacked it, copied defconfig, renamed it to 
.config and ran "make ARCH=arm menuconfig" (I prefer ncurses myself), 
then switched the appropriate option on and saved the new file. I wasn't 
sure whether I should also switch the FRAMEBUFFER_CONSOLE_DETECT_PRIMARY 
option as I was not sure of its meaning and whether I actually need 
this, so left it as the default (empty/No). When I ran diff to see what 
has been changed the following has been altered:

--- defconfig    2011-11-19 16:35:46.000000000 +0000
+++ .config    2011-12-03 15:42:13.123656047 +0000
@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
 # Linux kernel version: 2.6.32.9
-# Fri Aug 27 19:32:05 2010
+# Sat Dec  3 15:42:13 2011
 #
 CONFIG_ARM=y
 CONFIG_SYS_SUPPORTS_APM_EMULATION=y
@@ -1199,7 +1199,12 @@
 #
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_DUMMY_CONSOLE=y
-# CONFIG_FRAMEBUFFER_CONSOLE is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
+CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
 # CONFIG_LOGO is not set
 CONFIG_SOUND=y
 CONFIG_SOUND_OSS_CORE=y
@@ -1233,11 +1238,9 @@
 CONFIG_SND_SOC=y
 
 #
-# MSM SoC Audio support
+# SoC Audio support Qualcomm
 #
 CONFIG_SND_MSM_SOC=y
-CONFIG_SND_MSM_DAI_SOC=y
-CONFIG_SND_MSM_SOC_MSM7K=y
 CONFIG_SND_SOC_I2C_AND_SPI=y
 # CONFIG_SND_SOC_ALL_CODECS is not set
 # CONFIG_SOUND_PRIME is not set


Interesting! In addition to a few extra options, the two SND_MSM_* 
options shown above are now gone - don't know why.

Anyway, I copied this back to the appropriate directory and bumped the 
version number, then ran bitbake again. No problems and I've had my new 
image, kernel modules (recompiled) and a few other things. Installed it 
and fastbooted my phone. The screen appeared this time - rotated as well 
- and I've had my login prompt. Brilliant!

Duly logged in, but there were a few further problems:

1. The keyboard I now have is completely unusable as the "alt" register 
(the blue row of keys) is completely unusable/inaccessible with the 
exception of the top row (where the numbers are). That means I cannot 
type/use vital keys like the pipe symbol ('|'), dash ('-') etc. There is 
also no "repeat" - i.e. when I press a key and keep pressing it, it 
doesn't continue typing the same key. is there any way I could fix this?

2. My ssh login is also problematic - when I try to log in from the PC 
host (via usb) this time I get the following error on that (PC) end: 
"PTY allocation request failed on channel 0". Don't know why that is, 
any ideas?

I cannot properly scroll/see what is happening on the phone system and 
neither can I see any of the log files as the keyboard is all screwed 
up, so I can't post any of these file in order to further help resolve 
the above issues.

Re: fso-console-image problems

[Martin Jansa]

[-- Attachment #1: Type: text/plain, Size: 4636 bytes --]

On Sat, Dec 03, 2011 at 04:37:34PM +0000, Mr Dash Four wrote:
> 
> > Instead of trying to edit the file manually, try "make xconfig" in the 
> > directory where the kernel is extracted(something like work/htcdream*/linux-
> > leviathan*/git/ ) and do it manually trough the GUI, then save back the 
> > resulting defconfig, increase PR in the recipe and rebuild your console-image.
> >   
> That as a very good advice, thank you! The versioning "magic" is 
> something I didn't know about (I always used to delete all related files 
> in the tmp/stamp directory in the futile hope that the process/steps 
> will be repeated at the next run).
> 
> OK, since I use rm_work, the git directory is no longer there, but I've 
> had the git tar archive, so unpacked it, copied defconfig, renamed it to 
> .config and ran "make ARCH=arm menuconfig" (I prefer ncurses myself), 

then you will like:
bitbake -c menuconfig virtual/kernel 

and to save defconfig you can use -c savedefconfig (not 100% sure it's
available in linux-leviathan in OE-classic).

> then switched the appropriate option on and saved the new file. I wasn't 
> sure whether I should also switch the FRAMEBUFFER_CONSOLE_DETECT_PRIMARY 
> option as I was not sure of its meaning and whether I actually need 
> this, so left it as the default (empty/No). When I ran diff to see what 
> has been changed the following has been altered:
> 
> --- defconfig    2011-11-19 16:35:46.000000000 +0000
> +++ .config    2011-12-03 15:42:13.123656047 +0000
> @@ -1,7 +1,7 @@
>  #
>  # Automatically generated make config: don't edit
>  # Linux kernel version: 2.6.32.9
> -# Fri Aug 27 19:32:05 2010
> +# Sat Dec  3 15:42:13 2011
>  #
>  CONFIG_ARM=y
>  CONFIG_SYS_SUPPORTS_APM_EMULATION=y
> @@ -1199,7 +1199,12 @@
>  #
>  # CONFIG_VGA_CONSOLE is not set
>  CONFIG_DUMMY_CONSOLE=y
> -# CONFIG_FRAMEBUFFER_CONSOLE is not set
> +CONFIG_FRAMEBUFFER_CONSOLE=y
> +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
> +CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
> +# CONFIG_FONTS is not set
> +CONFIG_FONT_8x8=y
> +CONFIG_FONT_8x16=y
>  # CONFIG_LOGO is not set
>  CONFIG_SOUND=y
>  CONFIG_SOUND_OSS_CORE=y
> @@ -1233,11 +1238,9 @@
>  CONFIG_SND_SOC=y
>  
>  #
> -# MSM SoC Audio support
> +# SoC Audio support Qualcomm
>  #
>  CONFIG_SND_MSM_SOC=y
> -CONFIG_SND_MSM_DAI_SOC=y
> -CONFIG_SND_MSM_SOC_MSM7K=y
>  CONFIG_SND_SOC_I2C_AND_SPI=y
>  # CONFIG_SND_SOC_ALL_CODECS is not set
>  # CONFIG_SOUND_PRIME is not set
> 
> 
> Interesting! In addition to a few extra options, the two SND_MSM_* 
> options shown above are now gone - don't know why.
> 
> Anyway, I copied this back to the appropriate directory and bumped the 
> version number, then ran bitbake again. No problems and I've had my new 
> image, kernel modules (recompiled) and a few other things. Installed it 
> and fastbooted my phone. The screen appeared this time - rotated as well 
> - and I've had my login prompt. Brilliant!
> 
> Duly logged in, but there were a few further problems:
> 
> 1. The keyboard I now have is completely unusable as the "alt" register 
> (the blue row of keys) is completely unusable/inaccessible with the 
> exception of the top row (where the numbers are). That means I cannot 
> type/use vital keys like the pipe symbol ('|'), dash ('-') etc. There is 
> also no "repeat" - i.e. when I press a key and keep pressing it, it 
> doesn't continue typing the same key. is there any way I could fix this?

You need to add right keymap to keymaps recipe and check that it's in
/etc/keymap-2.6.map and then /etc/init.d/keymap.sh should load it for
you during boot.

> 2. My ssh login is also problematic - when I try to log in from the PC 
> host (via usb) this time I get the following error on that (PC) end: 
> "PTY allocation request failed on channel 0". Don't know why that is, 
> any ideas?

This usually means that /dev/pts wasn't mounted during boot, I don't
remember if htcdream was doing something weird but for palmpre GarthPS
needed this:
http://git.openembedded.org/openembedded/commit/?id=fcb43100609fcb955cfac6ad6b92d3b5ddf08c20
and I'm not sure if somebody tested htcdream since then.. so check order
of mountdevsubfs.sh and udev init if htcdream is using udev (not
devtmpfs)

> I cannot properly scroll/see what is happening on the phone system and 
> neither can I see any of the log files as the keyboard is all screwed 
> up, so I can't post any of these file in order to further help resolve 
> the above issues.

-- 
Martin 'JaMa' Jansa     jabber: Martin.Jansa@gmail.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 205 bytes --]

Re: fso-console-image problems

[Mr Dash Four]

> then you will like:
> bitbake -c menuconfig virtual/kernel 
>   
Indeed!

> and to save defconfig you can use -c savedefconfig (not 100% sure it's
> available in linux-leviathan in OE-classic).
>   
Nope, this doesn't seem available - it tells me "Nothing to do" and to 
run "bitbake world" if I want something done (I like that attitude :-) 
), so I had to copy the new file myself.

> You need to add right keymap to keymaps recipe and check that it's in
> /etc/keymap-2.6.map and then /etc/init.d/keymap.sh should load it for
> you during boot.
>   
Hmm, in my rootfs I do have /etc/init.d/keymap and I just looked at that 
script - it looks for either /etc/keymap-*something* or 
/etc/keymap-extension-*something*. I have neither!

In the recipe directory (keymaps/files) there is a directory called 
"htcuniversal" which has a single file called keymap-2.6.map:

#altgr keycode 18 = euro
altgr keycode 15 = tilde
altgr keycode 24 = slash
altgr keycode 25 = backslash
altgr keycode 32 = pound
altgr keycode 37 = quotedbl
altgr keycode 38 = apostrophe
altgr keycode 50 = question
altgr keycode 51 = semicolon
altgr keycode 52 = colon

Now, I have four questions:
1) how do I "activate" this keymap (provided it is the one I want);
2) it seems that in this file I could redefine *any* key I want. If so, 
is there any man/doc page I can look at to educate myself, because I am 
almost 100% certain that I would need to redefine some of the keys in 
the "standard" setting.
3) How do I find the "keycode" numbers - is there a tool I could execute 
(probably on my phone) to find a certain keycode when I press it so that 
I could redefine it later (presumably in a similar file as the 
keymap-2.6.map I listed above)?
4) When I do all the changes, do I just do the versioning "magic" (bump 
up the keymaps PR) in order to trigger a re-make of the stuff I changed 
(great trick that!)?

> This usually means that /dev/pts wasn't mounted during boot, I don't
> remember if htcdream was doing something weird but for palmpre GarthPS
> needed this:
> http://git.openembedded.org/openembedded/commit/?id=fcb43100609fcb955cfac6ad6b92d3b5ddf08c20
> and I'm not sure if somebody tested htcdream since then.. so check order
> of mountdevsubfs.sh and udev init if htcdream is using udev (not
> devtmpfs)
>   
Hmm, I don't know what OE commit I have, but just checked my /etc/rcS.d 
on the phone's rootfs - it seems that I have the (buggy) 
"S04mountdevsubfs.sh" instead of "S05mountdevsubfs.sh". How do I 
alter/change this (presumably by altering some of the recipes)?

Re: fso-console-image problems

[Martin Jansa]

[-- Attachment #1: Type: text/plain, Size: 3762 bytes --]

On Sat, Dec 03, 2011 at 05:47:01PM +0000, Mr Dash Four wrote:
> 
> > then you will like:
> > bitbake -c menuconfig virtual/kernel 
> >   
> Indeed!
> 
> > and to save defconfig you can use -c savedefconfig (not 100% sure it's
> > available in linux-leviathan in OE-classic).
> >   
> Nope, this doesn't seem available - it tells me "Nothing to do" and to 
> run "bitbake world" if I want something done (I like that attitude :-) 
> ), so I had to copy the new file myself.

You haven't specify target I guess..
bitbake -c savedefconfig virtual/kernel
 
> > You need to add right keymap to keymaps recipe and check that it's in
> > /etc/keymap-2.6.map and then /etc/init.d/keymap.sh should load it for
> > you during boot.
> >   
> Hmm, in my rootfs I do have /etc/init.d/keymap and I just looked at that 
> script - it looks for either /etc/keymap-*something* or 
> /etc/keymap-extension-*something*. I have neither!
> 
> In the recipe directory (keymaps/files) there is a directory called 
> "htcuniversal" which has a single file called keymap-2.6.map:
> #altgr keycode 18 = euro
> altgr keycode 15 = tilde
> altgr keycode 24 = slash
> altgr keycode 25 = backslash
> altgr keycode 32 = pound
> altgr keycode 37 = quotedbl
> altgr keycode 38 = apostrophe
> altgr keycode 50 = question
> altgr keycode 51 = semicolon
> altgr keycode 52 = colon
> 
> Now, I have four questions:
> 1) how do I "activate" this keymap (provided it is the one I want);

copy htcuniversal file to match MACHINE (so htcdream) and rebuild
keymaps recipe, don't know if htcuniversal is using same layout..

> 2) it seems that in this file I could redefine *any* key I want. If so, 
> is there any man/doc page I can look at to educate myself, because I am 
> almost 100% certain that I would need to redefine some of the keys in 
> the "standard" setting.

Yes there definetely are some man and doc pages as this is not really
OE or embedded specific and also there is google you know.. :).

> 3) How do I find the "keycode" numbers - is there a tool I could execute 
> (probably on my phone) to find a certain keycode when I press it so that 
> I could redefine it later (presumably in a similar file as the 
> keymap-2.6.map I listed above)?

dtto

> 4) When I do all the changes, do I just do the versioning "magic" (bump 
> up the keymaps PR) in order to trigger a re-make of the stuff I changed 
> (great trick that!)?

yes 
1) add file
2) bump PR,
3) rebuild
4) test it on device,
5) update it on device if it's not 100% correct and then sync keymap-2.6.map 
with htcdream in OE
6) send patch to OE ML

> > This usually means that /dev/pts wasn't mounted during boot, I don't
> > remember if htcdream was doing something weird but for palmpre GarthPS
> > needed this:
> > http://git.openembedded.org/openembedded/commit/?id=fcb43100609fcb955cfac6ad6b92d3b5ddf08c20
> > and I'm not sure if somebody tested htcdream since then.. so check order
> > of mountdevsubfs.sh and udev init if htcdream is using udev (not
> > devtmpfs)
> >   
> Hmm, I don't know what OE commit I have, but just checked my /etc/rcS.d 

And I cannot run commands (git log even) in your checkout so I don't know it too :).

> on the phone's rootfs - it seems that I have the (buggy) 
> "S04mountdevsubfs.sh" instead of "S05mountdevsubfs.sh". How do I 
> alter/change this (presumably by altering some of the recipes)?

Yes this is in initscripts-shr which are used only when you're building
SHR and shr-images, if you're still playing with fso- or default
console- iamges then IIRC normal initscript recipe is used and you have
to apply similar fix there..

-- 
Martin 'JaMa' Jansa     jabber: Martin.Jansa@gmail.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 205 bytes --]

Re: fso-console-image problems

[Mr Dash Four]

> You haven't specify target I guess..
> bitbake -c savedefconfig virtual/kernel
>   
Noted, thanks as always! I did try this but this time I am getting a 
make error from linux-leviathan_git recipe - "make savedefconfig" -> No 
rules to make target savedefconfig, so it is obviously not defined. 
Nevermind, I copied the file myself.

>> 1) how do I "activate" this keymap (provided it is the one I want);
>>     
>
> copy htcuniversal file to match MACHINE (so htcdream) and rebuild
> keymaps recipe, don't know if htcuniversal is using same layout..
>   
Noted, though what I did in the meantime is I logged in via ssh (see 
below :-) ), called nano, cut-and-paste job from my PC's htcuniversal 
keymap file, saved this as /etc/keymap-2.6.map (on the phone) and then 
executed /etc/init.d/keymap - the layout has changed somewhat but it is 
not what I need, so I am going to see if I could make the corrections I 
need so that this file matches the htcdream layout exactly.

There are quite a few "non-standard" keys (like "home", "back", two 
different "alt" keys, one "search" key etc) which I am hoping to capture 
with this layout config - will search google for the tool to use to see 
what scan codes they transmit (provided this is how the "keycode" works, 
that is).

What baffles me though is that I've had a very good layout on my 
shr-image (full GUI), but I can't see any keyboard map layouts there 
either - maybe the gui terminal I've been using there defines its own 
layouts in some different way?

>> 4) When I do all the changes, do I just do the versioning "magic" (bump 
>> up the keymaps PR) in order to trigger a re-make of the stuff I changed 
>> (great trick that!)?
>>     
>
> yes 
> 1) add file
> 2) bump PR,
> 3) rebuild
> 4) test it on device,
> 5) update it on device if it's not 100% correct and then sync keymap-2.6.map 
> with htcdream in OE
> 6) send patch to OE ML
>   
Noted, will do!

>> Hmm, I don't know what OE commit I have, but just checked my /etc/rcS.d 
>>     
>
> And I cannot run commands (git log even) in your checkout so I don't know it too :).
>   
It turns out that correcting this error (which is what I did do) fixes 
this as I am now able to use ssh and log in remotely. One other annoying 
thing - I don't seem to have "/var/log/messages" anywhere on this phone 
- everything is shown on the screen - is this something I could alter as 
well?

> Yes this is in initscripts-shr which are used only when you're building
> SHR and shr-images, if you're still playing with fso- or default
> console- iamges then IIRC normal initscript recipe is used and you have
> to apply similar fix there..
>   
I just did a grep on the entire recipes directory and apart from the 
shr-initscript recipe nothing else is there, so I altered that recipe 
(and bumped the version number to trigger a rebuild).

Re: fso-console-image problems

[Mr Dash Four]

> Noted, though what I did in the meantime is I logged in via ssh (see 
> below :-) ), called nano, cut-and-paste job from my PC's htcuniversal 
> keymap file, saved this as /etc/keymap-2.6.map (on the phone) and then 
> executed /etc/init.d/keymap - the layout has changed somewhat but it 
> is not what I need, so I am going to see if I could make the 
> corrections I need so that this file matches the htcdream layout exactly.
>
> There are quite a few "non-standard" keys (like "home", "back", two 
> different "alt" keys, one "search" key etc) which I am hoping to 
> capture with this layout config - will search google for the tool to 
> use to see what scan codes they transmit (provided this is how the 
> "keycode" works, that is).
Not having much luck with this at the moment! I dumped the entire 
key-mapping configuration to a separate file using dumpkeys and tried, 
as a test, to reconfigure a non-standard key (called 'menu') to emit the 
letter 'z' when pressed - at least that was the idea.

When I ran "showkeys -s" (to see what was the scan code of that key) I 
noted it as "0xe0 0x5e", so I then did the following: "setkeycodes e05e 
44" (44 in the already-dumped keymap is defined as "keycode 44 = +z +Z 
+z Control_z Control_z Meta_z Meta_Control_z"). After doing that, I 
pressed the "menu" key a couple of times, but nothing happened.

I then tried to remap another "non-standard" key - my "Back" key on the 
actual phone, but again nothing happens (when I press it, it emits '?' 
*regardless* of whether this key is re-defined by me or not). Lastly, I 
tried to do this trick on a "known" key - '1' (scancode 2): no problem, 
it emits the letter 'z' as it should.

I don't know if I am doing this wrong and why it doesn't work with 
"non-standard" keys, maybe the kernel keyboard driver is somehow 
"stopping" these - I have no idea at this point!