* [PATCH] OMAP3: RX-51: complete tsc2005 controller support @ 2011-12-14 13:01 Vladimir Zapolskiy 2011-12-14 13:02 ` [PATCH v2] " Vladimir Zapolskiy 2011-12-14 15:45 ` [PATCH] " Aaro Koskinen 0 siblings, 2 replies; 6+ messages in thread From: Vladimir Zapolskiy @ 2011-12-14 13:01 UTC (permalink / raw) To: linux-omap, linux-input; +Cc: Dmitry Torokhov, Aaro Koskinen, Tony Lindgren This change adds initialization of TSC2005 touchscreen controller found on Nokia RX-51 board. The change is taken from MeeGo kernel adaptation for Nokia N900, it repeats the work of Aaro Koskinen and Mika Laitio, the original discussion is at http://www.mail-archive.com/linux-omap@vger.kernel.org/msg26749.html Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@nokia.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Aaro Koskinen <aaro.koskinen@nokia.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> --- arch/arm/mach-omap2/board-rx51-peripherals.c | 45 ++++++++++++++++++++++++- 1 files changed, 43 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c index ba1aa07..f30484e 100644 --- a/arch/arm/mach-omap2/board-rx51-peripherals.c +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c @@ -15,6 +15,7 @@ #include <linux/input/matrix_keypad.h> #include <linux/spi/spi.h> #include <linux/wl12xx.h> +#include <linux/spi/tsc2005.h> #include <linux/i2c.h> #include <linux/i2c/twl.h> #include <linux/clk.h> @@ -56,6 +57,9 @@ #define RX51_FMTX_IRQ 53 #define RX51_LP5523_CHIP_EN_GPIO 41 +#define RX51_TSC2005_RESET_GPIO 104 +#define RX51_TSC2005_IRQ_GPIO 100 + #define RX51_USB_TRANSCEIVER_RST_GPIO 67 /* list all spi devices here */ @@ -146,6 +150,17 @@ static struct omap2_mcspi_device_config tsc2005_mcspi_config = { .single_channel = 1, }; +static struct tsc2005_platform_data tsc2005_pdata = { + .ts_pressure_max = 2048, + .ts_pressure_fudge = 2, + .ts_x_max = 4096, + .ts_x_fudge = 4, + .ts_y_max = 4096, + .ts_y_fudge = 4, + .ts_x_plate_ohm = 320, + .esd_timeout_ms = 8000, +}; + static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = { [RX51_SPI_WL1251] = { .modalias = "wl1251", @@ -167,10 +182,10 @@ static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = { .modalias = "tsc2005", .bus_num = 1, .chip_select = 0, - /* .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO),*/ + .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO), .max_speed_hz = 6000000, .controller_data = &tsc2005_mcspi_config, - /* .platform_data = &tsc2005_config,*/ + .platform_data = &tsc2005_pdata, }, }; @@ -1086,6 +1101,31 @@ error: */ } +static void rx51_tsc2005_set_reset(bool enable) +{ + gpio_set_value(RX51_TSC2005_RESET_GPIO, enable); +} + +static void __init rx51_init_tsc2005(void) +{ + int r; + + r = gpio_request(RX51_TSC2005_IRQ_GPIO, "tsc2005 IRQ"); + if (r >= 0) + gpio_direction_input(RX51_TSC2005_IRQ_GPIO); + else + printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 IRQ"); + + r = gpio_request(RX51_TSC2005_RESET_GPIO, "tsc2005 reset"); + if (r >= 0) { + gpio_direction_output(RX51_TSC2005_RESET_GPIO, 1); + tsc2005_pdata.set_reset = rx51_tsc2005_set_reset; + } else { + printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 reset"); + tsc2005_pdata.esd_timeout_ms = 0; + } +} + void __init rx51_peripherals_init(void) { rx51_i2c_init(); @@ -1094,6 +1134,7 @@ void __init rx51_peripherals_init(void) board_smc91x_init(); rx51_add_gpio_keys(); rx51_init_wl1251(); + rx51_init_tsc2005(); rx51_init_si4713(); spi_register_board_info(rx51_peripherals_spi_board_info, ARRAY_SIZE(rx51_peripherals_spi_board_info)); -- 1.7.2.3 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v2] OMAP3: RX-51: complete tsc2005 controller support 2011-12-14 13:01 [PATCH] OMAP3: RX-51: complete tsc2005 controller support Vladimir Zapolskiy @ 2011-12-14 13:02 ` Vladimir Zapolskiy 2011-12-14 14:32 ` Igor Grinberg 2011-12-14 15:45 ` [PATCH] " Aaro Koskinen 1 sibling, 1 reply; 6+ messages in thread From: Vladimir Zapolskiy @ 2011-12-14 13:02 UTC (permalink / raw) To: linux-omap, linux-input; +Cc: Dmitry Torokhov, Aaro Koskinen, Tony Lindgren This change adds initialization of TSC2005 touchscreen controller found on Nokia RX-51 board. The change is taken from MeeGo kernel adaptation for Nokia N900, it repeats the work of Aaro Koskinen and Mika Laitio, the original discussion is at http://www.mail-archive.com/linux-omap@vger.kernel.org/msg26749.html Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@nokia.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Aaro Koskinen <aaro.koskinen@nokia.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> --- Changes from v1 to v2: * whitespace fix arch/arm/mach-omap2/board-rx51-peripherals.c | 45 ++++++++++++++++++++++++- 1 files changed, 43 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c index ba1aa07..f30484e 100644 --- a/arch/arm/mach-omap2/board-rx51-peripherals.c +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c @@ -15,6 +15,7 @@ #include <linux/input/matrix_keypad.h> #include <linux/spi/spi.h> #include <linux/wl12xx.h> +#include <linux/spi/tsc2005.h> #include <linux/i2c.h> #include <linux/i2c/twl.h> #include <linux/clk.h> @@ -56,6 +57,9 @@ #define RX51_FMTX_IRQ 53 #define RX51_LP5523_CHIP_EN_GPIO 41 +#define RX51_TSC2005_RESET_GPIO 104 +#define RX51_TSC2005_IRQ_GPIO 100 + #define RX51_USB_TRANSCEIVER_RST_GPIO 67 /* list all spi devices here */ @@ -146,6 +150,17 @@ static struct omap2_mcspi_device_config tsc2005_mcspi_config = { .single_channel = 1, }; +static struct tsc2005_platform_data tsc2005_pdata = { + .ts_pressure_max = 2048, + .ts_pressure_fudge = 2, + .ts_x_max = 4096, + .ts_x_fudge = 4, + .ts_y_max = 4096, + .ts_y_fudge = 4, + .ts_x_plate_ohm = 320, + .esd_timeout_ms = 8000, +}; + static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = { [RX51_SPI_WL1251] = { .modalias = "wl1251", @@ -167,10 +182,10 @@ static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = { .modalias = "tsc2005", .bus_num = 1, .chip_select = 0, - /* .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO),*/ + .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO), .max_speed_hz = 6000000, .controller_data = &tsc2005_mcspi_config, - /* .platform_data = &tsc2005_config,*/ + .platform_data = &tsc2005_pdata, }, }; @@ -1086,6 +1101,31 @@ error: */ } +static void rx51_tsc2005_set_reset(bool enable) +{ + gpio_set_value(RX51_TSC2005_RESET_GPIO, enable); +} + +static void __init rx51_init_tsc2005(void) +{ + int r; + + r = gpio_request(RX51_TSC2005_IRQ_GPIO, "tsc2005 IRQ"); + if (r >= 0) + gpio_direction_input(RX51_TSC2005_IRQ_GPIO); + else + printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 IRQ"); + + r = gpio_request(RX51_TSC2005_RESET_GPIO, "tsc2005 reset"); + if (r >= 0) { + gpio_direction_output(RX51_TSC2005_RESET_GPIO, 1); + tsc2005_pdata.set_reset = rx51_tsc2005_set_reset; + } else { + printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 reset"); + tsc2005_pdata.esd_timeout_ms = 0; + } +} + void __init rx51_peripherals_init(void) { rx51_i2c_init(); @@ -1094,6 +1134,7 @@ void __init rx51_peripherals_init(void) board_smc91x_init(); rx51_add_gpio_keys(); rx51_init_wl1251(); + rx51_init_tsc2005(); rx51_init_si4713(); spi_register_board_info(rx51_peripherals_spi_board_info, ARRAY_SIZE(rx51_peripherals_spi_board_info)); -- 1.7.2.3 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v2] OMAP3: RX-51: complete tsc2005 controller support 2011-12-14 13:02 ` [PATCH v2] " Vladimir Zapolskiy @ 2011-12-14 14:32 ` Igor Grinberg 2011-12-14 15:39 ` Vladimir Zapolskiy 0 siblings, 1 reply; 6+ messages in thread From: Igor Grinberg @ 2011-12-14 14:32 UTC (permalink / raw) To: Vladimir Zapolskiy Cc: linux-omap, linux-input, Dmitry Torokhov, Aaro Koskinen, Tony Lindgren Hi Vladimir, On 12/14/11 15:02, Vladimir Zapolskiy wrote: > This change adds initialization of TSC2005 touchscreen controller found on Nokia > RX-51 board. > > The change is taken from MeeGo kernel adaptation for Nokia N900, it repeats the > work of Aaro Koskinen and Mika Laitio, the original discussion is at > http://www.mail-archive.com/linux-omap@vger.kernel.org/msg26749.html > > Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@nokia.com> > Cc: Tony Lindgren <tony@atomide.com> > Cc: Aaro Koskinen <aaro.koskinen@nokia.com> > Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> > --- > Changes from v1 to v2: > * whitespace fix > > arch/arm/mach-omap2/board-rx51-peripherals.c | 45 ++++++++++++++++++++++++- > 1 files changed, 43 insertions(+), 2 deletions(-) > > diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c > index ba1aa07..f30484e 100644 > --- a/arch/arm/mach-omap2/board-rx51-peripherals.c > +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c > @@ -15,6 +15,7 @@ > #include <linux/input/matrix_keypad.h> > #include <linux/spi/spi.h> > #include <linux/wl12xx.h> > +#include <linux/spi/tsc2005.h> > #include <linux/i2c.h> > #include <linux/i2c/twl.h> > #include <linux/clk.h> > @@ -56,6 +57,9 @@ > #define RX51_FMTX_IRQ 53 > #define RX51_LP5523_CHIP_EN_GPIO 41 > > +#define RX51_TSC2005_RESET_GPIO 104 > +#define RX51_TSC2005_IRQ_GPIO 100 > + > #define RX51_USB_TRANSCEIVER_RST_GPIO 67 > > /* list all spi devices here */ > @@ -146,6 +150,17 @@ static struct omap2_mcspi_device_config tsc2005_mcspi_config = { > .single_channel = 1, > }; > > +static struct tsc2005_platform_data tsc2005_pdata = { > + .ts_pressure_max = 2048, > + .ts_pressure_fudge = 2, > + .ts_x_max = 4096, > + .ts_x_fudge = 4, > + .ts_y_max = 4096, > + .ts_y_fudge = 4, > + .ts_x_plate_ohm = 320, > + .esd_timeout_ms = 8000, > +}; > + > static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = { > [RX51_SPI_WL1251] = { > .modalias = "wl1251", > @@ -167,10 +182,10 @@ static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = { > .modalias = "tsc2005", > .bus_num = 1, > .chip_select = 0, > - /* .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO),*/ > + .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO), > .max_speed_hz = 6000000, > .controller_data = &tsc2005_mcspi_config, > - /* .platform_data = &tsc2005_config,*/ > + .platform_data = &tsc2005_pdata, > }, > }; > > @@ -1086,6 +1101,31 @@ error: > */ > } > > +static void rx51_tsc2005_set_reset(bool enable) > +{ > + gpio_set_value(RX51_TSC2005_RESET_GPIO, enable); > +} > + > +static void __init rx51_init_tsc2005(void) > +{ > + int r; > + > + r = gpio_request(RX51_TSC2005_IRQ_GPIO, "tsc2005 IRQ"); > + if (r >= 0) > + gpio_direction_input(RX51_TSC2005_IRQ_GPIO); > + else > + printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 IRQ"); > + > + r = gpio_request(RX51_TSC2005_RESET_GPIO, "tsc2005 reset"); > + if (r >= 0) { > + gpio_direction_output(RX51_TSC2005_RESET_GPIO, 1); > + tsc2005_pdata.set_reset = rx51_tsc2005_set_reset; > + } else { > + printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 reset"); > + tsc2005_pdata.esd_timeout_ms = 0; > + } I would suggest using gpio_request_array() here, or if those pins are independent from each other, for some reason, then gpio_request_one() would do. Also, don't you need to setup the mux for these GPIOs? Or is it done in some other place (like bootloader)? > +} > + > void __init rx51_peripherals_init(void) > { > rx51_i2c_init(); > @@ -1094,6 +1134,7 @@ void __init rx51_peripherals_init(void) > board_smc91x_init(); > rx51_add_gpio_keys(); > rx51_init_wl1251(); > + rx51_init_tsc2005(); > rx51_init_si4713(); > spi_register_board_info(rx51_peripherals_spi_board_info, > ARRAY_SIZE(rx51_peripherals_spi_board_info)); -- Regards, Igor. ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v2] OMAP3: RX-51: complete tsc2005 controller support 2011-12-14 14:32 ` Igor Grinberg @ 2011-12-14 15:39 ` Vladimir Zapolskiy 0 siblings, 0 replies; 6+ messages in thread From: Vladimir Zapolskiy @ 2011-12-14 15:39 UTC (permalink / raw) To: ext Igor Grinberg Cc: linux-omap, linux-input, Dmitry Torokhov, Aaro Koskinen, Tony Lindgren Hi Igor, thanks for review. On 12/14/2011 04:32 PM, ext Igor Grinberg wrote: > Hi Vladimir, > > On 12/14/11 15:02, Vladimir Zapolskiy wrote: >> This change adds initialization of TSC2005 touchscreen controller found on Nokia >> RX-51 board. >> >> The change is taken from MeeGo kernel adaptation for Nokia N900, it repeats the >> work of Aaro Koskinen and Mika Laitio, the original discussion is at >> http://www.mail-archive.com/linux-omap@vger.kernel.org/msg26749.html >> >> Signed-off-by: Vladimir Zapolskiy<vladimir.zapolskiy@nokia.com> >> Cc: Tony Lindgren<tony@atomide.com> >> Cc: Aaro Koskinen<aaro.koskinen@nokia.com> >> Cc: Dmitry Torokhov<dmitry.torokhov@gmail.com> >> --- >> Changes from v1 to v2: >> * whitespace fix >> >> arch/arm/mach-omap2/board-rx51-peripherals.c | 45 ++++++++++++++++++++++++- >> 1 files changed, 43 insertions(+), 2 deletions(-) >> >> diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c >> index ba1aa07..f30484e 100644 >> --- a/arch/arm/mach-omap2/board-rx51-peripherals.c >> +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c >> @@ -15,6 +15,7 @@ >> #include<linux/input/matrix_keypad.h> >> #include<linux/spi/spi.h> >> #include<linux/wl12xx.h> >> +#include<linux/spi/tsc2005.h> >> #include<linux/i2c.h> >> #include<linux/i2c/twl.h> >> #include<linux/clk.h> >> @@ -56,6 +57,9 @@ >> #define RX51_FMTX_IRQ 53 >> #define RX51_LP5523_CHIP_EN_GPIO 41 >> >> +#define RX51_TSC2005_RESET_GPIO 104 >> +#define RX51_TSC2005_IRQ_GPIO 100 >> + >> #define RX51_USB_TRANSCEIVER_RST_GPIO 67 >> >> /* list all spi devices here */ >> @@ -146,6 +150,17 @@ static struct omap2_mcspi_device_config tsc2005_mcspi_config = { >> .single_channel = 1, >> }; >> >> +static struct tsc2005_platform_data tsc2005_pdata = { >> + .ts_pressure_max = 2048, >> + .ts_pressure_fudge = 2, >> + .ts_x_max = 4096, >> + .ts_x_fudge = 4, >> + .ts_y_max = 4096, >> + .ts_y_fudge = 4, >> + .ts_x_plate_ohm = 320, >> + .esd_timeout_ms = 8000, >> +}; >> + >> static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = { >> [RX51_SPI_WL1251] = { >> .modalias = "wl1251", >> @@ -167,10 +182,10 @@ static struct spi_board_info rx51_peripherals_spi_board_info[] __initdata = { >> .modalias = "tsc2005", >> .bus_num = 1, >> .chip_select = 0, >> - /* .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO),*/ >> + .irq = OMAP_GPIO_IRQ(RX51_TSC2005_IRQ_GPIO), >> .max_speed_hz = 6000000, >> .controller_data =&tsc2005_mcspi_config, >> - /* .platform_data =&tsc2005_config,*/ >> + .platform_data =&tsc2005_pdata, >> }, >> }; >> >> @@ -1086,6 +1101,31 @@ error: >> */ >> } >> >> +static void rx51_tsc2005_set_reset(bool enable) >> +{ >> + gpio_set_value(RX51_TSC2005_RESET_GPIO, enable); >> +} >> + >> +static void __init rx51_init_tsc2005(void) >> +{ >> + int r; >> + >> + r = gpio_request(RX51_TSC2005_IRQ_GPIO, "tsc2005 IRQ"); >> + if (r>= 0) >> + gpio_direction_input(RX51_TSC2005_IRQ_GPIO); >> + else >> + printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 IRQ"); >> + >> + r = gpio_request(RX51_TSC2005_RESET_GPIO, "tsc2005 reset"); >> + if (r>= 0) { >> + gpio_direction_output(RX51_TSC2005_RESET_GPIO, 1); >> + tsc2005_pdata.set_reset = rx51_tsc2005_set_reset; >> + } else { >> + printk(KERN_ERR "unable to get %s GPIO\n", "tsc2005 reset"); >> + tsc2005_pdata.esd_timeout_ms = 0; >> + } > > I would suggest using gpio_request_array() here, > or if those pins are independent from each other, for some reason, > then gpio_request_one() would do. These pins are actually independent, but I agree that it would be simpler and therefore better to use gpio_request_array() here. > Also, don't you need to setup the mux for these GPIOs? > Or is it done in some other place (like bootloader)? I presume it's done in the original bootloader, however it won't harm to add explicit pin mux definitions. >> +} >> + >> void __init rx51_peripherals_init(void) >> { >> rx51_i2c_init(); >> @@ -1094,6 +1134,7 @@ void __init rx51_peripherals_init(void) >> board_smc91x_init(); >> rx51_add_gpio_keys(); >> rx51_init_wl1251(); >> + rx51_init_tsc2005(); >> rx51_init_si4713(); >> spi_register_board_info(rx51_peripherals_spi_board_info, >> ARRAY_SIZE(rx51_peripherals_spi_board_info)); > -- With best wishes, Vladimir ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] OMAP3: RX-51: complete tsc2005 controller support 2011-12-14 13:01 [PATCH] OMAP3: RX-51: complete tsc2005 controller support Vladimir Zapolskiy 2011-12-14 13:02 ` [PATCH v2] " Vladimir Zapolskiy @ 2011-12-14 15:45 ` Aaro Koskinen 2011-12-14 15:59 ` Vladimir Zapolskiy 1 sibling, 1 reply; 6+ messages in thread From: Aaro Koskinen @ 2011-12-14 15:45 UTC (permalink / raw) To: Vladimir Zapolskiy Cc: linux-omap, linux-input, Dmitry Torokhov, Aaro Koskinen, Tony Lindgren Hi, On Wed, 14 Dec 2011, Vladimir Zapolskiy wrote: > This change adds initialization of TSC2005 touchscreen controller > found on Nokia RX-51 board. > > The change is taken from MeeGo kernel adaptation for Nokia N900, > it repeats the work of Aaro Koskinen and Mika Laitio, the original > discussion is at > http://www.mail-archive.com/linux-omap@vger.kernel.org/msg26749.html I think Tony applied this already: http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap.git;a=commit;h=3dad5356aa47097cf67027cf0a07298b4f5baef6 And that patch was from Maemo, not MeeGo kernel... A. ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] OMAP3: RX-51: complete tsc2005 controller support 2011-12-14 15:45 ` [PATCH] " Aaro Koskinen @ 2011-12-14 15:59 ` Vladimir Zapolskiy 0 siblings, 0 replies; 6+ messages in thread From: Vladimir Zapolskiy @ 2011-12-14 15:59 UTC (permalink / raw) To: Aaro Koskinen; +Cc: linux-omap, linux-input, Dmitry Torokhov, Tony Lindgren Hi, On 12/14/2011 05:45 PM, Aaro Koskinen wrote: > Hi, > > On Wed, 14 Dec 2011, Vladimir Zapolskiy wrote: >> This change adds initialization of TSC2005 touchscreen controller >> found on Nokia RX-51 board. >> >> The change is taken from MeeGo kernel adaptation for Nokia N900, >> it repeats the work of Aaro Koskinen and Mika Laitio, the original >> discussion is at >> http://www.mail-archive.com/linux-omap@vger.kernel.org/msg26749.html > > I think Tony applied this already: > > http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap.git;a=commit;h=3dad5356aa47097cf67027cf0a07298b4f5baef6 > great, I haven't noticed that initially. In that case please ignore the duplicate. > > And that patch was from Maemo, not MeeGo kernel... > > A. -- With best wishes, Vladimir ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2011-12-14 15:59 UTC | newest] Thread overview: 6+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2011-12-14 13:01 [PATCH] OMAP3: RX-51: complete tsc2005 controller support Vladimir Zapolskiy 2011-12-14 13:02 ` [PATCH v2] " Vladimir Zapolskiy 2011-12-14 14:32 ` Igor Grinberg 2011-12-14 15:39 ` Vladimir Zapolskiy 2011-12-14 15:45 ` [PATCH] " Aaro Koskinen 2011-12-14 15:59 ` Vladimir Zapolskiy
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.