* Anysee E30 S2 plus
@ 2011-12-20 1:04 Jesper Krogh
2011-12-20 8:07 ` Antti Palosaari
0 siblings, 1 reply; 5+ messages in thread
From: Jesper Krogh @ 2011-12-20 1:04 UTC (permalink / raw)
To: linux-media
[-- Attachment #1: Type: text/plain, Size: 190 bytes --]
Hi
I have a brand new Anysee E30 S2 plus, but with most recent
media_build.git - it is reported as the wrong model.
I have attached a copy of my lsusb output.
Best regards
Jesper Krogh
[-- Attachment #2: E30S2plus --]
[-- Type: application/octet-stream, Size: 4905 bytes --]
Device: ID 1c73:861f AMT Anysee E30 USB 2.0 DVB-T Receiver
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x1c73 AMT
idProduct 0x861f Anysee E30 USB 2.0 DVB-T Receiver
bcdDevice 1.00
iManufacturer 1 AMT.CO.KR
iProduct 2 anysee-S2(LP)
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 83
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 4
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 1
bNumEndpoints 4
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x1400 3x 1024 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x1400 3x 1024 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0002
(Bus Powered)
Remote Wakeup Enabled
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: Anysee E30 S2 plus
2011-12-20 1:04 Anysee E30 S2 plus Jesper Krogh
@ 2011-12-20 8:07 ` Antti Palosaari
2011-12-20 12:10 ` Jesper Krogh
0 siblings, 1 reply; 5+ messages in thread
From: Antti Palosaari @ 2011-12-20 8:07 UTC (permalink / raw)
To: Jesper Krogh; +Cc: linux-media
On 12/20/2011 03:04 AM, Jesper Krogh wrote:
> Hi
>
> I have a brand new Anysee E30 S2 plus, but with most recent
> media_build.git - it is reported as the wrong model.
>
> I have attached a copy of my lsusb output.
That don't help at all. You should look from system log what it says.
Use dmesg command for that.
Antti
--
http://palosaari.fi/
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Anysee E30 S2 plus
2011-12-20 8:07 ` Antti Palosaari
@ 2011-12-20 12:10 ` Jesper Krogh
2011-12-20 15:15 ` Antti Palosaari
0 siblings, 1 reply; 5+ messages in thread
From: Jesper Krogh @ 2011-12-20 12:10 UTC (permalink / raw)
To: linux-media
Ok. I had my doubts on whether to include that or not - But here it is
/Jesper
[ 1053.784044] usb 1-6: new high speed USB device number 7 using ehci_hcd
[ 1054.556036] usb 1-6: device not accepting address 7, error -71
[ 1054.668043] usb 1-6: new high speed USB device number 8 using ehci_hcd
[ 1056.136482] usb 1-6: config 1 interface 0 altsetting 0 bulk
endpoint 0x1 has invalid maxpacket 64
[ 1056.136492] usb 1-6: config 1 interface 0 altsetting 0 bulk
endpoint 0x81 has invalid maxpacket 64
[ 1056.136501] usb 1-6: config 1 interface 0 altsetting 1 bulk
endpoint 0x1 has invalid maxpacket 64
[ 1056.136508] usb 1-6: config 1 interface 0 altsetting 1 bulk
endpoint 0x81 has invalid maxpacket 64
[ 1056.137448] dvb-usb: found a 'Anysee DVB USB2.0' in warm state.
[ 1056.137553] dvb-usb: will pass the complete MPEG2 transport stream
to the software demuxer.
[ 1056.137559] dvb-usb: will pass the complete MPEG2 transport stream
to the software demuxer.
[ 1056.137882] DVB: registering new adapter (Anysee DVB USB2.0)
[ 1056.141938] anysee: firmware version:1.3 hardware id:11
[ 1056.145212] Invalid probe, probably not a CX24116 device
[ 1056.145231] anysee: Unsupported Anysee version. Please report the
<linux-media@vger.kernel.org>.
[ 1056.145239] dvb-usb: no frontend was attached by 'Anysee DVB USB2.0'
[ 1056.145473] Registered IR keymap rc-anysee
[ 1056.145709] input: IR-receiver inside an USB DVB receiver as
/devices/pci0000:00/0000:00:1d.7/usb1/1-6/rc/rc1/input15
[ 1056.145858] rc1: IR-receiver inside an USB DVB receiver as
/devices/pci0000:00/0000:00:1d.7/usb1/1-6/rc/rc1
[ 1056.145866] dvb-usb: schedule remote query interval to 250 msecs.
[ 1056.145873] dvb-usb: Anysee DVB USB2.0 successfully initialized and
connected.
On Tue, Dec 20, 2011 at 5:07 AM, Antti Palosaari <crope@iki.fi> wrote:
> On 12/20/2011 03:04 AM, Jesper Krogh wrote:
>>
>> Hi
>>
>> I have a brand new Anysee E30 S2 plus, but with most recent
>> media_build.git - it is reported as the wrong model.
>>
>> I have attached a copy of my lsusb output.
>
>
> That don't help at all. You should look from system log what it says. Use
> dmesg command for that.
>
>
> Antti
>
>
> --
> http://palosaari.fi/
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Anysee E30 S2 plus
2011-12-20 12:10 ` Jesper Krogh
@ 2011-12-20 15:15 ` Antti Palosaari
2012-01-26 23:12 ` Antti Palosaari
0 siblings, 1 reply; 5+ messages in thread
From: Antti Palosaari @ 2011-12-20 15:15 UTC (permalink / raw)
To: Jesper Krogh; +Cc: linux-media
On 12/20/2011 02:10 PM, Jesper Krogh wrote:
> Ok. I had my doubts on whether to include that or not - But here it is
>
> /Jesper
>
> [ 1056.137882] DVB: registering new adapter (Anysee DVB USB2.0)
> [ 1056.141938] anysee: firmware version:1.3 hardware id:11
> [ 1056.145212] Invalid probe, probably not a CX24116 device
> [ 1056.145231] anysee: Unsupported Anysee version. Please report the
> <linux-media@vger.kernel.org>.
Check your power supply is connected. It do same here without power
supply since demod is powered using external power supply.
If not then it is most likely firmware issue. I have very old firmware,
maybe one of the first devel versions.
regards
Antti
--
http://palosaari.fi/
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Anysee E30 S2 plus
2011-12-20 15:15 ` Antti Palosaari
@ 2012-01-26 23:12 ` Antti Palosaari
0 siblings, 0 replies; 5+ messages in thread
From: Antti Palosaari @ 2012-01-26 23:12 UTC (permalink / raw)
To: Jesper Krogh; +Cc: linux-media
On 12/20/2011 05:15 PM, Antti Palosaari wrote:
> On 12/20/2011 02:10 PM, Jesper Krogh wrote:
>> Ok. I had my doubts on whether to include that or not - But here it is
>>
>> /Jesper
>>
>> [ 1056.137882] DVB: registering new adapter (Anysee DVB USB2.0)
>> [ 1056.141938] anysee: firmware version:1.3 hardware id:11
>> [ 1056.145212] Invalid probe, probably not a CX24116 device
>> [ 1056.145231] anysee: Unsupported Anysee version. Please report the
>> <linux-media@vger.kernel.org>.
>
> Check your power supply is connected. It do same here without power
> supply since demod is powered using external power supply.
>
> If not then it is most likely firmware issue. I have very old firmware,
> maybe one of the first devel versions.
I got today similar bug report and after debugging we found there is
different hardware. Whole NIM, that is box containing demodulator and
tuner, is different. Instead of old CX24116 there is same NIM than can
be found from the E7 serie DVB-S2 receiver.
So I have to get this new revision of that device in order to add
support for it... Sorry :/
regards
Antti
--
http://palosaari.fi/
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2012-01-26 23:12 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-12-20 1:04 Anysee E30 S2 plus Jesper Krogh
2011-12-20 8:07 ` Antti Palosaari
2011-12-20 12:10 ` Jesper Krogh
2011-12-20 15:15 ` Antti Palosaari
2012-01-26 23:12 ` Antti Palosaari
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.