usb, davinci: usb 2.0 problem on an am1808 based board

[hs@denx.de (Heiko Schocher)]

Hello Manjunathappa,

On 22.05.2012 09:22, Heiko Schocher wrote:
> Hello Manjunathappa,
>
> Manjunathappa, Prakash wrote:
>> Hi Heiko,
>>
>> On Mon, May 21, 2012 at 11:40:33, Heiko Schocher wrote:
>>> Hello Manjunathappa,
>>>
>>> Manjunathappa, Prakash wrote:
>>>> Hi Heiko,
>>>>
>>>> I do not know how putting delay helped MSC device detection.
>>>> Can you please check if MUSB is coming up in "b_idle" state(by
>>>> $cat /sys/devices/platform/musb-da8xx/musb-hdrc/mode)?
>>>> State should move to b_peripheral on connecting gadget cable.
>>> We have connected the USB0_ID pin to ground ->  host only mode, so
>>> I could not try this.
>>>
>>
>> Ok, So it is coming up in which state, "$cat /sys/devices/platform/musb-da8xx/musb-hdrc/mode"?
>
> without the delay in da8xx_musb_interrupt() and the
> +       musb->a_wait_bcon = OTG_TIME_A_WAIT_BCON;
>   change:
>
> booting Linux with USB stick attached shows:
> root at armv5te:~# cat /sys/devices/platform/musb-da8xx/musb-hdrc/mode
> a_host
> root at armv5te:~#
>
> booting Linux without USB stick attached:
>
> root at armv5te:~# cat /sys/devices/platform/musb-da8xx/musb-hdrc/mode
> a_wait_vrise
> root at armv5te:~#
>
> and connecting an usb stick:
>
> root at armv5te:~# cat /sys/devices/platform/musb-da8xx/musb-hdrc/mode
> a_host
> root at armv5te:~#
>
>>>> If you connect MSC device via mini-A connector, state should change to "a_host".
>>>> OTG timer is responsible for above state changes, can you please check if below
>>>> changes are present?
>>>> diff --git a/drivers/usb/musb/da8xx.c b/drivers/usb/musb/da8xx.c index 4da7492..a1a692e 100644
>>>> --- a/drivers/usb/musb/da8xx.c
>>>> +++ b/drivers/usb/musb/da8xx.c
>>>> @@ -76,6 +76,7 @@
>>>>   #define DA8XX_INTR_TX_SHIFT    0
>>>>   #define DA8XX_INTR_TX_MASK     (DA8XX_USB_TX_EP_MASK<<  DA8XX_INTR_TX_SHIFT)
>>>>
>>>> +#define A_WAIT_BCON_TIMEOUT     1100            /* in ms */
>>>>   #define DA8XX_MENTOR_CORE_OFFSET 0x400
>>>>
>>>>   #define CFGCHIP2       IO_ADDRESS(DA8XX_SYSCFG0_BASE + DA8XX_CFGCHIP2_REG)
>>>> @@ -443,6 +444,7 @@ static int da8xx_musb_init(struct musb *musb)
>>>>                   rev, __raw_readl(CFGCHIP2),
>>>>                   musb_readb(reg_base, DA8XX_USB_CTRL_REG));
>>>>
>>>> +       musb->a_wait_bcon = A_WAIT_BCON_TIMEOUT;
>>>>          musb->isr = da8xx_musb_interrupt;
>>>>          return 0;
>>>>   fail:
>>> No, this change is not in current mainline ...
>>>
>>> Added this patch, and I get:
>>>
>>> $ make -s uImage
>>> drivers/usb/musb/da8xx.c: In function 'da8xx_musb_init':
>>> drivers/usb/musb/da8xx.c:448:22: error: 'A_WAIT_BCON_TIMEOUT' undeclared (first use in this function)
>>> drivers/usb/musb/da8xx.c:448:22: note: each undeclared identifier is reported only once for each function it appears in
>>> make[3]: *** [drivers/usb/musb/da8xx.o] Error 1
>>> make[2]: *** [drivers/usb/musb] Error 2
>>> make[1]: *** [drivers/usb] Error 2
>>> make: *** [drivers] Error 2
>>> $
>>>
>>> Do you mean
>>>
>>> musb->a_wait_bcon = OTG_TIME_A_WAIT_BCON;
>>>
>>> ? This is setup in musb_core.c::allocate_instance() as Sergei Shtylyov
>>> already commented ... nevertheless tried with this define your patch,
>>> and my USB stick gets detected too...
>>>
>>
>> Does that mean issue got fixed or Do you still have delay in da8xx_musb_interrupt handler?
>
> Without the delay in the da8xx_musb_interrupt() ...

ping!

How do we proceed here?

bye,
Heiko
-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany