[PATCH 67/90] staging: comedi: dt3000: remove 'phys_addr' from the private data

[PATCH 67/90] staging: comedi: dt3000: remove 'phys_addr' from the private data

[H Hartley Sweeten]

The 'phys_addr' variable in the private data is simply used as
a flag for the detach function to know that the pci device has
been enabled. Use the 'dev->iobase' variable instead as is more
typical for other comedi pci drivers.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/staging/comedi/drivers/dt3000.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

diff --git a/drivers/staging/comedi/drivers/dt3000.c b/drivers/staging/comedi/drivers/dt3000.c
index 92558e7..3937e87 100644
--- a/drivers/staging/comedi/drivers/dt3000.c
+++ b/drivers/staging/comedi/drivers/dt3000.c
@@ -250,7 +250,6 @@ static const struct dt3k_boardtype dt3k_boardtypes[] = {
 struct dt3k_private {
 
 	struct pci_dev *pci_dev;
-	resource_size_t phys_addr;
 	void __iomem *io_addr;
 	unsigned int lock;
 	unsigned int ao_readback[2];
@@ -824,8 +823,8 @@ static int dt3000_attach(struct comedi_device *dev, struct comedi_devconfig *it)
 	if (ret < 0)
 		return ret;
 
-	devpriv->phys_addr = pci_resource_start(pcidev, 0);
-	devpriv->io_addr = ioremap(devpriv->phys_addr, DT3000_SIZE);
+	dev->iobase = pci_resource_start(pcidev, 0);
+	devpriv->io_addr = ioremap(dev->iobase, DT3000_SIZE);
 	if (!devpriv->io_addr)
 		return -ENOMEM;
 
@@ -905,7 +904,7 @@ static void dt3000_detach(struct comedi_device *dev)
 		free_irq(dev->irq, dev);
 	if (devpriv) {
 		if (devpriv->pci_dev) {
-			if (devpriv->phys_addr)
+			if (dev->iobase)
 				comedi_pci_disable(devpriv->pci_dev);
 			pci_dev_put(devpriv->pci_dev);
 		}
-- 
1.7.11

Re: [PATCH 67/90] staging: comedi: dt3000: remove 'phys_addr' from the private data

[Ian Abbott]

On 2012-07-19 02:58, H Hartley Sweeten wrote:
> The 'phys_addr' variable in the private data is simply used as
> a flag for the detach function to know that the pci device has
> been enabled. Use the 'dev->iobase' variable instead as is more
> typical for other comedi pci drivers.

I think dev->iobase is really only meant to hold I/O port addresses, 
although it is wide enough to hold a 32-bit PCI memory address.

> Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
> Cc: Ian Abbott <abbotti@mev.co.uk>
> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> ---
>   drivers/staging/comedi/drivers/dt3000.c | 7 +++----
>   1 file changed, 3 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/staging/comedi/drivers/dt3000.c b/drivers/staging/comedi/drivers/dt3000.c
> index 92558e7..3937e87 100644
> --- a/drivers/staging/comedi/drivers/dt3000.c
> +++ b/drivers/staging/comedi/drivers/dt3000.c
> @@ -250,7 +250,6 @@ static const struct dt3k_boardtype dt3k_boardtypes[] = {
>   struct dt3k_private {
>
>   	struct pci_dev *pci_dev;
> -	resource_size_t phys_addr;
>   	void __iomem *io_addr;
>   	unsigned int lock;
>   	unsigned int ao_readback[2];
> @@ -824,8 +823,8 @@ static int dt3000_attach(struct comedi_device *dev, struct comedi_devconfig *it)
>   	if (ret < 0)
>   		return ret;
>
> -	devpriv->phys_addr = pci_resource_start(pcidev, 0);
> -	devpriv->io_addr = ioremap(devpriv->phys_addr, DT3000_SIZE);
> +	dev->iobase = pci_resource_start(pcidev, 0);
> +	devpriv->io_addr = ioremap(dev->iobase, DT3000_SIZE);

dev->iobase is an unsigned long, which may be narrower than a 
resource_size_t.  You should really pass the full-width resource_size_t 
value to ioremap().

You could even set dev->iobase to some dummy non-zero value as a flag 
for the detach() routine to call comedi_pci_disable() as dev->iobase is 
not used for anything else.

>   	if (!devpriv->io_addr)
>   		return -ENOMEM;
>
> @@ -905,7 +904,7 @@ static void dt3000_detach(struct comedi_device *dev)
>   		free_irq(dev->irq, dev);
>   	if (devpriv) {
>   		if (devpriv->pci_dev) {
> -			if (devpriv->phys_addr)
> +			if (dev->iobase)
>   				comedi_pci_disable(devpriv->pci_dev);
>   			pci_dev_put(devpriv->pci_dev);
>   		}
>


-- 
-=( Ian Abbott @ MEV Ltd.    E-mail: <abbotti@mev.co.uk>        )=-
-=( Tel: +44 (0)161 477 1898   FAX: +44 (0)161 718 3587         )=-