[PATCH 0/4] i2c: omap: few more patches

[PATCH 0/4] i2c: omap: few more patches

[Felipe Balbi]

Just a few extra patches on top of the earlier series I sent.

With these patches, we have threaded irq support and autosuspend support for
i2c-omap driver.

All patches boot tested with pandaboard.

Felipe Balbi (4):
  i2c: omap: always return IRQ_HANDLED
  i2c: omap: switch to threaded IRQ support
  i2c: omap: remove unnecessary pm_runtime_suspended check
  i2c: omap: switch over to autosuspend API

 drivers/i2c/busses/i2c-omap.c | 53 ++++++++++++++++++++++++++++++++++---------
 1 file changed, 42 insertions(+), 11 deletions(-)

-- 
1.7.12.rc0

[PATCH 0/4] i2c: omap: few more patches

[Felipe Balbi]

Just a few extra patches on top of the earlier series I sent.

With these patches, we have threaded irq support and autosuspend support for
i2c-omap driver.

All patches boot tested with pandaboard.

Felipe Balbi (4):
  i2c: omap: always return IRQ_HANDLED
  i2c: omap: switch to threaded IRQ support
  i2c: omap: remove unnecessary pm_runtime_suspended check
  i2c: omap: switch over to autosuspend API

 drivers/i2c/busses/i2c-omap.c | 53 ++++++++++++++++++++++++++++++++++---------
 1 file changed, 42 insertions(+), 11 deletions(-)

-- 
1.7.12.rc0

[PATCH 1/4] i2c: omap: always return IRQ_HANDLED

[Felipe Balbi]

even if our clocks are disabled, we still
handled the IRQ, so we should return IRQ_HANDLED.

Signed-off-by: Felipe Balbi <balbi@ti.com>
---
 drivers/i2c/busses/i2c-omap.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 2dd2301..f5eafb7 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -862,7 +862,7 @@ omap_i2c_isr(int this_irq, void *dev_id)
 	int err = 0, count = 0;
 
 	if (pm_runtime_suspended(dev->dev))
-		return IRQ_NONE;
+		return IRQ_HANDLED;
 
 	do {
 		bits = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG);
-- 
1.7.12.rc0

[PATCH 1/4] i2c: omap: always return IRQ_HANDLED

[Felipe Balbi]

even if our clocks are disabled, we still
handled the IRQ, so we should return IRQ_HANDLED.

Signed-off-by: Felipe Balbi <balbi@ti.com>
---
 drivers/i2c/busses/i2c-omap.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 2dd2301..f5eafb7 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -862,7 +862,7 @@ omap_i2c_isr(int this_irq, void *dev_id)
 	int err = 0, count = 0;
 
 	if (pm_runtime_suspended(dev->dev))
-		return IRQ_NONE;
+		return IRQ_HANDLED;
 
 	do {
 		bits = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG);
-- 
1.7.12.rc0

[PATCH 2/4] i2c: omap: switch to threaded IRQ support

[Felipe Balbi]

for OMAP2, we can easily switch over to threaded
IRQs on the I2C driver. This will allow us to
spend less time in hardirq context.

Signed-off-by: Felipe Balbi <balbi@ti.com>
---
 drivers/i2c/busses/i2c-omap.c | 42 ++++++++++++++++++++++++++++++++++++------
 1 file changed, 36 insertions(+), 6 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index f5eafb7..a3db053 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -176,6 +176,7 @@ enum {
 #define I2C_OMAP_ERRATA_I462		(1 << 1)
 
 struct omap_i2c_dev {
+	spinlock_t		lock;		/* IRQ synchronization */
 	struct device		*dev;
 	void __iomem		*base;		/* virtual */
 	int			irq;
@@ -854,9 +855,30 @@ static int omap_i2c_transmit_data(struct omap_i2c_dev *dev, u8 num_bytes,
 }
 
 static irqreturn_t
-omap_i2c_isr(int this_irq, void *dev_id)
+omap_i2c_isr(int irq, void *dev_id)
 {
 	struct omap_i2c_dev *dev = dev_id;
+	irqreturn_t ret = IRQ_HANDLED;
+	u16 mask;
+	u16 stat;
+
+	spin_lock(&dev->lock);
+	mask = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG);
+	stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);
+
+	if (stat & mask)
+		ret = IRQ_WAKE_THREAD;
+
+	spin_unlock(&dev->lock);
+
+	return ret;
+}
+
+static irqreturn_t
+omap_i2c_isr_thread(int this_irq, void *dev_id)
+{
+	struct omap_i2c_dev *dev = dev_id;
+	unsigned long flags;
 	u16 bits;
 	u16 stat;
 	int err = 0, count = 0;
@@ -864,6 +886,7 @@ omap_i2c_isr(int this_irq, void *dev_id)
 	if (pm_runtime_suspended(dev->dev))
 		return IRQ_HANDLED;
 
+	spin_lock_irqsave(&dev->lock, flags);
 	do {
 		bits = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG);
 		stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);
@@ -877,6 +900,7 @@ omap_i2c_isr(int this_irq, void *dev_id)
 
 		if (!stat) {
 			/* my work here is done */
+			spin_unlock_irqrestore(&dev->lock, flags);
 			return IRQ_HANDLED;
 		}
 
@@ -985,6 +1009,8 @@ omap_i2c_isr(int this_irq, void *dev_id)
 
 out:
 	omap_i2c_complete_cmd(dev, err);
+	spin_unlock_irqrestore(&dev->lock, flags);
+
 	return IRQ_HANDLED;
 }
 
@@ -1028,7 +1054,6 @@ omap_i2c_probe(struct platform_device *pdev)
 	struct omap_i2c_bus_platform_data *pdata = pdev->dev.platform_data;
 	struct device_node	*node = pdev->dev.of_node;
 	const struct of_device_id *match;
-	irq_handler_t isr;
 	int irq;
 	int r;
 
@@ -1078,6 +1103,8 @@ omap_i2c_probe(struct platform_device *pdev)
 	dev->dev = &pdev->dev;
 	dev->irq = irq;
 
+	spin_lock_init(&dev->lock);
+
 	platform_set_drvdata(pdev, dev);
 	init_completion(&dev->cmd_complete);
 
@@ -1130,10 +1157,13 @@ omap_i2c_probe(struct platform_device *pdev)
 	/* reset ASAP, clearing any IRQs */
 	omap_i2c_init(dev);
 
-	isr = (dev->rev < OMAP_I2C_OMAP1_REV_2) ? omap_i2c_omap1_isr :
-								   omap_i2c_isr;
-	r = devm_request_irq(&pdev->dev, dev->irq, isr, IRQF_NO_SUSPEND,
-			     pdev->name, dev);
+	if (dev->rev < OMAP_I2C_OMAP1_REV_2)
+		r = devm_request_irq(&pdev->dev, dev->irq, omap_i2c_omap1_isr,
+				IRQF_NO_SUSPEND, pdev->name, dev);
+	else
+		r = devm_request_threaded_irq(&pdev->dev, dev->irq, omap_i2c_isr,
+				omap_i2c_isr_thread, IRQF_NO_SUSPEND | IRQF_ONESHOT,
+				pdev->name, dev);
 
 	if (r) {
 		dev_err(dev->dev, "failure requesting irq %i\n", dev->irq);
-- 
1.7.12.rc0

[PATCH 2/4] i2c: omap: switch to threaded IRQ support

[Felipe Balbi]

for OMAP2, we can easily switch over to threaded
IRQs on the I2C driver. This will allow us to
spend less time in hardirq context.

Signed-off-by: Felipe Balbi <balbi@ti.com>
---
 drivers/i2c/busses/i2c-omap.c | 42 ++++++++++++++++++++++++++++++++++++------
 1 file changed, 36 insertions(+), 6 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index f5eafb7..a3db053 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -176,6 +176,7 @@ enum {
 #define I2C_OMAP_ERRATA_I462		(1 << 1)
 
 struct omap_i2c_dev {
+	spinlock_t		lock;		/* IRQ synchronization */
 	struct device		*dev;
 	void __iomem		*base;		/* virtual */
 	int			irq;
@@ -854,9 +855,30 @@ static int omap_i2c_transmit_data(struct omap_i2c_dev *dev, u8 num_bytes,
 }
 
 static irqreturn_t
-omap_i2c_isr(int this_irq, void *dev_id)
+omap_i2c_isr(int irq, void *dev_id)
 {
 	struct omap_i2c_dev *dev = dev_id;
+	irqreturn_t ret = IRQ_HANDLED;
+	u16 mask;
+	u16 stat;
+
+	spin_lock(&dev->lock);
+	mask = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG);
+	stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);
+
+	if (stat & mask)
+		ret = IRQ_WAKE_THREAD;
+
+	spin_unlock(&dev->lock);
+
+	return ret;
+}
+
+static irqreturn_t
+omap_i2c_isr_thread(int this_irq, void *dev_id)
+{
+	struct omap_i2c_dev *dev = dev_id;
+	unsigned long flags;
 	u16 bits;
 	u16 stat;
 	int err = 0, count = 0;
@@ -864,6 +886,7 @@ omap_i2c_isr(int this_irq, void *dev_id)
 	if (pm_runtime_suspended(dev->dev))
 		return IRQ_HANDLED;
 
+	spin_lock_irqsave(&dev->lock, flags);
 	do {
 		bits = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG);
 		stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);
@@ -877,6 +900,7 @@ omap_i2c_isr(int this_irq, void *dev_id)
 
 		if (!stat) {
 			/* my work here is done */
+			spin_unlock_irqrestore(&dev->lock, flags);
 			return IRQ_HANDLED;
 		}
 
@@ -985,6 +1009,8 @@ omap_i2c_isr(int this_irq, void *dev_id)
 
 out:
 	omap_i2c_complete_cmd(dev, err);
+	spin_unlock_irqrestore(&dev->lock, flags);
+
 	return IRQ_HANDLED;
 }
 
@@ -1028,7 +1054,6 @@ omap_i2c_probe(struct platform_device *pdev)
 	struct omap_i2c_bus_platform_data *pdata = pdev->dev.platform_data;
 	struct device_node	*node = pdev->dev.of_node;
 	const struct of_device_id *match;
-	irq_handler_t isr;
 	int irq;
 	int r;
 
@@ -1078,6 +1103,8 @@ omap_i2c_probe(struct platform_device *pdev)
 	dev->dev = &pdev->dev;
 	dev->irq = irq;
 
+	spin_lock_init(&dev->lock);
+
 	platform_set_drvdata(pdev, dev);
 	init_completion(&dev->cmd_complete);
 
@@ -1130,10 +1157,13 @@ omap_i2c_probe(struct platform_device *pdev)
 	/* reset ASAP, clearing any IRQs */
 	omap_i2c_init(dev);
 
-	isr = (dev->rev < OMAP_I2C_OMAP1_REV_2) ? omap_i2c_omap1_isr :
-								   omap_i2c_isr;
-	r = devm_request_irq(&pdev->dev, dev->irq, isr, IRQF_NO_SUSPEND,
-			     pdev->name, dev);
+	if (dev->rev < OMAP_I2C_OMAP1_REV_2)
+		r = devm_request_irq(&pdev->dev, dev->irq, omap_i2c_omap1_isr,
+				IRQF_NO_SUSPEND, pdev->name, dev);
+	else
+		r = devm_request_threaded_irq(&pdev->dev, dev->irq, omap_i2c_isr,
+				omap_i2c_isr_thread, IRQF_NO_SUSPEND | IRQF_ONESHOT,
+				pdev->name, dev);
 
 	if (r) {
 		dev_err(dev->dev, "failure requesting irq %i\n", dev->irq);
-- 
1.7.12.rc0

[PATCH 3/4] i2c: omap: remove unnecessary pm_runtime_suspended check

[Felipe Balbi]

before starting any messages we call pm_runtime_get_sync()
which will make sure that by the time we program a transfer
and our IRQ handler gets called, we're not suspended
anymore.

Signed-off-by: Felipe Balbi <balbi@ti.com>
---
 drivers/i2c/busses/i2c-omap.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index a3db053..60928f2 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -883,9 +883,6 @@ omap_i2c_isr_thread(int this_irq, void *dev_id)
 	u16 stat;
 	int err = 0, count = 0;
 
-	if (pm_runtime_suspended(dev->dev))
-		return IRQ_HANDLED;
-
 	spin_lock_irqsave(&dev->lock, flags);
 	do {
 		bits = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG);
-- 
1.7.12.rc0

[PATCH 3/4] i2c: omap: remove unnecessary pm_runtime_suspended check

[Felipe Balbi]

before starting any messages we call pm_runtime_get_sync()
which will make sure that by the time we program a transfer
and our IRQ handler gets called, we're not suspended
anymore.

Signed-off-by: Felipe Balbi <balbi@ti.com>
---
 drivers/i2c/busses/i2c-omap.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index a3db053..60928f2 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -883,9 +883,6 @@ omap_i2c_isr_thread(int this_irq, void *dev_id)
 	u16 stat;
 	int err = 0, count = 0;
 
-	if (pm_runtime_suspended(dev->dev))
-		return IRQ_HANDLED;
-
 	spin_lock_irqsave(&dev->lock, flags);
 	do {
 		bits = omap_i2c_read_reg(dev, OMAP_I2C_IE_REG);
-- 
1.7.12.rc0

[PATCH 4/4] i2c: omap: switch over to autosuspend API

[Felipe Balbi]

this helps us reduce unnecessary pm transitions
in case we have another i2c message been started
soon.

Signed-off-by: Felipe Balbi <balbi@ti.com>
---
 drivers/i2c/busses/i2c-omap.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 60928f2..22efaba 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -645,7 +645,8 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
 
 	omap_i2c_wait_for_bb(dev);
 out:
-	pm_runtime_put(dev->dev);
+	pm_runtime_mark_last_busy(dev->dev);
+	pm_runtime_put_autosuspend(dev->dev);
 	return r;
 }
 
@@ -1113,6 +1114,9 @@ omap_i2c_probe(struct platform_device *pdev)
 		dev->regs = (u8 *)reg_map_ip_v1;
 
 	pm_runtime_enable(dev->dev);
+	pm_runtime_set_autosuspend_delay(dev->dev, 1000);
+	pm_runtime_use_autosuspend(dev->dev);
+
 	r = pm_runtime_get_sync(dev->dev);
 	if (IS_ERR_VALUE(r))
 		goto err_free_mem;
@@ -1189,7 +1193,7 @@ omap_i2c_probe(struct platform_device *pdev)
 
 	of_i2c_register_devices(adap);
 
-	pm_runtime_put(dev->dev);
+	pm_runtime_put_autosuspend(dev->dev);
 
 	return 0;
 
-- 
1.7.12.rc0

[PATCH 4/4] i2c: omap: switch over to autosuspend API

[Felipe Balbi]

this helps us reduce unnecessary pm transitions
in case we have another i2c message been started
soon.

Signed-off-by: Felipe Balbi <balbi@ti.com>
---
 drivers/i2c/busses/i2c-omap.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 60928f2..22efaba 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -645,7 +645,8 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
 
 	omap_i2c_wait_for_bb(dev);
 out:
-	pm_runtime_put(dev->dev);
+	pm_runtime_mark_last_busy(dev->dev);
+	pm_runtime_put_autosuspend(dev->dev);
 	return r;
 }
 
@@ -1113,6 +1114,9 @@ omap_i2c_probe(struct platform_device *pdev)
 		dev->regs = (u8 *)reg_map_ip_v1;
 
 	pm_runtime_enable(dev->dev);
+	pm_runtime_set_autosuspend_delay(dev->dev, 1000);
+	pm_runtime_use_autosuspend(dev->dev);
+
 	r = pm_runtime_get_sync(dev->dev);
 	if (IS_ERR_VALUE(r))
 		goto err_free_mem;
@@ -1189,7 +1193,7 @@ omap_i2c_probe(struct platform_device *pdev)
 
 	of_i2c_register_devices(adap);
 
-	pm_runtime_put(dev->dev);
+	pm_runtime_put_autosuspend(dev->dev);
 
 	return 0;
 
-- 
1.7.12.rc0

Re: [PATCH 4/4] i2c: omap: switch over to autosuspend API

[Shubhrajyoti]

Hi Felipe,
On Monday 06 August 2012 07:48 PM, Felipe Balbi wrote:
> this helps us reduce unnecessary pm transitions
> in case we have another i2c message been started
> soon.
>
> Signed-off-by: Felipe Balbi <balbi@ti.com>
> ---
>  drivers/i2c/busses/i2c-omap.c | 8 ++++++--
>  1 file changed, 6 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
> index 60928f2..22efaba 100644
> --- a/drivers/i2c/busses/i2c-omap.c
> +++ b/drivers/i2c/busses/i2c-omap.c
> @@ -645,7 +645,8 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
>  
>  	omap_i2c_wait_for_bb(dev);
>  out:
> -	pm_runtime_put(dev->dev);
> +	pm_runtime_mark_last_busy(dev->dev);
> +	pm_runtime_put_autosuspend(dev->dev);
>  	return r;
>  }
>  
> @@ -1113,6 +1114,9 @@ omap_i2c_probe(struct platform_device *pdev)
>  		dev->regs = (u8 *)reg_map_ip_v1;
>  
>  	pm_runtime_enable(dev->dev);
> +	pm_runtime_set_autosuspend_delay(dev->dev, 1000);
> +	pm_runtime_use_autosuspend(dev->dev);
> +
>  	r = pm_runtime_get_sync(dev->dev);
>  	if (IS_ERR_VALUE(r))
>  		goto err_free_mem;
> @@ -1189,7 +1193,7 @@ omap_i2c_probe(struct platform_device *pdev)
>  
>  	of_i2c_register_devices(adap);
>  
> -	pm_runtime_put(dev->dev);
Should we mark it last busy stamp here here?
Or it may not take effect till the first transaction.


> +	pm_runtime_put_autosuspend(dev->dev);
>  
>  	return 0;
>  

[PATCH 4/4] i2c: omap: switch over to autosuspend API

[Shubhrajyoti]

Hi Felipe,
On Monday 06 August 2012 07:48 PM, Felipe Balbi wrote:
> this helps us reduce unnecessary pm transitions
> in case we have another i2c message been started
> soon.
>
> Signed-off-by: Felipe Balbi <balbi@ti.com>
> ---
>  drivers/i2c/busses/i2c-omap.c | 8 ++++++--
>  1 file changed, 6 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
> index 60928f2..22efaba 100644
> --- a/drivers/i2c/busses/i2c-omap.c
> +++ b/drivers/i2c/busses/i2c-omap.c
> @@ -645,7 +645,8 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
>  
>  	omap_i2c_wait_for_bb(dev);
>  out:
> -	pm_runtime_put(dev->dev);
> +	pm_runtime_mark_last_busy(dev->dev);
> +	pm_runtime_put_autosuspend(dev->dev);
>  	return r;
>  }
>  
> @@ -1113,6 +1114,9 @@ omap_i2c_probe(struct platform_device *pdev)
>  		dev->regs = (u8 *)reg_map_ip_v1;
>  
>  	pm_runtime_enable(dev->dev);
> +	pm_runtime_set_autosuspend_delay(dev->dev, 1000);
> +	pm_runtime_use_autosuspend(dev->dev);
> +
>  	r = pm_runtime_get_sync(dev->dev);
>  	if (IS_ERR_VALUE(r))
>  		goto err_free_mem;
> @@ -1189,7 +1193,7 @@ omap_i2c_probe(struct platform_device *pdev)
>  
>  	of_i2c_register_devices(adap);
>  
> -	pm_runtime_put(dev->dev);
Should we mark it last busy stamp here here?
Or it may not take effect till the first transaction.


> +	pm_runtime_put_autosuspend(dev->dev);
>  
>  	return 0;
>  

Re: [PATCH 4/4] i2c: omap: switch over to autosuspend API

[Felipe Balbi]

[-- Attachment #1: Type: text/plain, Size: 1400 bytes --]

Hi,

On Mon, Aug 06, 2012 at 05:18:57PM +0300, Felipe Balbi wrote:
> this helps us reduce unnecessary pm transitions
> in case we have another i2c message been started
> soon.
> 
> Signed-off-by: Felipe Balbi <balbi@ti.com>
> ---
>  drivers/i2c/busses/i2c-omap.c | 8 ++++++--
>  1 file changed, 6 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
> index 60928f2..22efaba 100644
> --- a/drivers/i2c/busses/i2c-omap.c
> +++ b/drivers/i2c/busses/i2c-omap.c
> @@ -645,7 +645,8 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
>  
>  	omap_i2c_wait_for_bb(dev);
>  out:
> -	pm_runtime_put(dev->dev);
> +	pm_runtime_mark_last_busy(dev->dev);
> +	pm_runtime_put_autosuspend(dev->dev);
>  	return r;
>  }
>  
> @@ -1113,6 +1114,9 @@ omap_i2c_probe(struct platform_device *pdev)
>  		dev->regs = (u8 *)reg_map_ip_v1;
>  
>  	pm_runtime_enable(dev->dev);
> +	pm_runtime_set_autosuspend_delay(dev->dev, 1000);
> +	pm_runtime_use_autosuspend(dev->dev);
> +
>  	r = pm_runtime_get_sync(dev->dev);
>  	if (IS_ERR_VALUE(r))
>  		goto err_free_mem;
> @@ -1189,7 +1193,7 @@ omap_i2c_probe(struct platform_device *pdev)
>  
>  	of_i2c_register_devices(adap);
>  
> -	pm_runtime_put(dev->dev);
> +	pm_runtime_put_autosuspend(dev->dev);

Probably... nice catch. Will send v2

-- 
balbi

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

[PATCH 4/4] i2c: omap: switch over to autosuspend API

[Felipe Balbi]

Hi,

On Mon, Aug 06, 2012 at 05:18:57PM +0300, Felipe Balbi wrote:
> this helps us reduce unnecessary pm transitions
> in case we have another i2c message been started
> soon.
> 
> Signed-off-by: Felipe Balbi <balbi@ti.com>
> ---
>  drivers/i2c/busses/i2c-omap.c | 8 ++++++--
>  1 file changed, 6 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
> index 60928f2..22efaba 100644
> --- a/drivers/i2c/busses/i2c-omap.c
> +++ b/drivers/i2c/busses/i2c-omap.c
> @@ -645,7 +645,8 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
>  
>  	omap_i2c_wait_for_bb(dev);
>  out:
> -	pm_runtime_put(dev->dev);
> +	pm_runtime_mark_last_busy(dev->dev);
> +	pm_runtime_put_autosuspend(dev->dev);
>  	return r;
>  }
>  
> @@ -1113,6 +1114,9 @@ omap_i2c_probe(struct platform_device *pdev)
>  		dev->regs = (u8 *)reg_map_ip_v1;
>  
>  	pm_runtime_enable(dev->dev);
> +	pm_runtime_set_autosuspend_delay(dev->dev, 1000);
> +	pm_runtime_use_autosuspend(dev->dev);
> +
>  	r = pm_runtime_get_sync(dev->dev);
>  	if (IS_ERR_VALUE(r))
>  		goto err_free_mem;
> @@ -1189,7 +1193,7 @@ omap_i2c_probe(struct platform_device *pdev)
>  
>  	of_i2c_register_devices(adap);
>  
> -	pm_runtime_put(dev->dev);
> +	pm_runtime_put_autosuspend(dev->dev);

Probably... nice catch. Will send v2

-- 
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20120807/c737c871/attachment.sig>

[PATCH] i2c: omap: switch over to autosuspend API

[Felipe Balbi]

this helps us reduce unnecessary pm transitions
in case we have another i2c message been started
soon.

Signed-off-by: Felipe Balbi <balbi@ti.com>
---
 drivers/i2c/busses/i2c-omap.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 60928f2..c210b45 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -645,7 +645,8 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
 
 	omap_i2c_wait_for_bb(dev);
 out:
-	pm_runtime_put(dev->dev);
+	pm_runtime_mark_last_busy(dev->dev);
+	pm_runtime_put_autosuspend(dev->dev);
 	return r;
 }
 
@@ -1113,6 +1114,9 @@ omap_i2c_probe(struct platform_device *pdev)
 		dev->regs = (u8 *)reg_map_ip_v1;
 
 	pm_runtime_enable(dev->dev);
+	pm_runtime_set_autosuspend_delay(dev->dev, 1000);
+	pm_runtime_use_autosuspend(dev->dev);
+
 	r = pm_runtime_get_sync(dev->dev);
 	if (IS_ERR_VALUE(r))
 		goto err_free_mem;
@@ -1189,7 +1193,8 @@ omap_i2c_probe(struct platform_device *pdev)
 
 	of_i2c_register_devices(adap);
 
-	pm_runtime_put(dev->dev);
+	pm_runtime_mark_last_busy(dev->dev);
+	pm_runtime_put_autosuspend(dev->dev);
 
 	return 0;
 
-- 
1.7.12.rc0

[PATCH] i2c: omap: switch over to autosuspend API

[Felipe Balbi]

this helps us reduce unnecessary pm transitions
in case we have another i2c message been started
soon.

Signed-off-by: Felipe Balbi <balbi@ti.com>
---
 drivers/i2c/busses/i2c-omap.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 60928f2..c210b45 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -645,7 +645,8 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
 
 	omap_i2c_wait_for_bb(dev);
 out:
-	pm_runtime_put(dev->dev);
+	pm_runtime_mark_last_busy(dev->dev);
+	pm_runtime_put_autosuspend(dev->dev);
 	return r;
 }
 
@@ -1113,6 +1114,9 @@ omap_i2c_probe(struct platform_device *pdev)
 		dev->regs = (u8 *)reg_map_ip_v1;
 
 	pm_runtime_enable(dev->dev);
+	pm_runtime_set_autosuspend_delay(dev->dev, 1000);
+	pm_runtime_use_autosuspend(dev->dev);
+
 	r = pm_runtime_get_sync(dev->dev);
 	if (IS_ERR_VALUE(r))
 		goto err_free_mem;
@@ -1189,7 +1193,8 @@ omap_i2c_probe(struct platform_device *pdev)
 
 	of_i2c_register_devices(adap);
 
-	pm_runtime_put(dev->dev);
+	pm_runtime_mark_last_busy(dev->dev);
+	pm_runtime_put_autosuspend(dev->dev);
 
 	return 0;
 
-- 
1.7.12.rc0

RE: [PATCH] i2c: omap: switch over to autosuspend API

[Bedia, Vaibhav]

On Tue, Aug 07, 2012 at 17:41:08, Balbi, Felipe wrote:
> this helps us reduce unnecessary pm transitions
> in case we have another i2c message been started
> soon.
>

s/been started/starting ?
 
> Signed-off-by: Felipe Balbi <balbi@ti.com>
> ---
>  drivers/i2c/busses/i2c-omap.c | 9 +++++++--
>  1 file changed, 7 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
> index 60928f2..c210b45 100644
> --- a/drivers/i2c/busses/i2c-omap.c
> +++ b/drivers/i2c/busses/i2c-omap.c
> @@ -645,7 +645,8 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
>  
>  	omap_i2c_wait_for_bb(dev);
>  out:
> -	pm_runtime_put(dev->dev);
> +	pm_runtime_mark_last_busy(dev->dev);
> +	pm_runtime_put_autosuspend(dev->dev);
>  	return r;
>  }
>  
> @@ -1113,6 +1114,9 @@ omap_i2c_probe(struct platform_device *pdev)
>  		dev->regs = (u8 *)reg_map_ip_v1;
>  
>  	pm_runtime_enable(dev->dev);
> +	pm_runtime_set_autosuspend_delay(dev->dev, 1000);

I guess there will always be a debate around what's the right
delay for autosuspend ;)

You can at least replace the magic number with a macro.

> +	pm_runtime_use_autosuspend(dev->dev);
> +
>  	r = pm_runtime_get_sync(dev->dev);
>  	if (IS_ERR_VALUE(r))
>  		goto err_free_mem;
> @@ -1189,7 +1193,8 @@ omap_i2c_probe(struct platform_device *pdev)
>  
>  	of_i2c_register_devices(adap);
>  
> -	pm_runtime_put(dev->dev);
> +	pm_runtime_mark_last_busy(dev->dev);
> +	pm_runtime_put_autosuspend(dev->dev);
>  
>  	return 0;
>  
> -- 
> 1.7.12.rc0
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> 

[PATCH] i2c: omap: switch over to autosuspend API

[Bedia, Vaibhav]

On Tue, Aug 07, 2012 at 17:41:08, Balbi, Felipe wrote:
> this helps us reduce unnecessary pm transitions
> in case we have another i2c message been started
> soon.
>

s/been started/starting ?
 
> Signed-off-by: Felipe Balbi <balbi@ti.com>
> ---
>  drivers/i2c/busses/i2c-omap.c | 9 +++++++--
>  1 file changed, 7 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
> index 60928f2..c210b45 100644
> --- a/drivers/i2c/busses/i2c-omap.c
> +++ b/drivers/i2c/busses/i2c-omap.c
> @@ -645,7 +645,8 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
>  
>  	omap_i2c_wait_for_bb(dev);
>  out:
> -	pm_runtime_put(dev->dev);
> +	pm_runtime_mark_last_busy(dev->dev);
> +	pm_runtime_put_autosuspend(dev->dev);
>  	return r;
>  }
>  
> @@ -1113,6 +1114,9 @@ omap_i2c_probe(struct platform_device *pdev)
>  		dev->regs = (u8 *)reg_map_ip_v1;
>  
>  	pm_runtime_enable(dev->dev);
> +	pm_runtime_set_autosuspend_delay(dev->dev, 1000);

I guess there will always be a debate around what's the right
delay for autosuspend ;)

You can at least replace the magic number with a macro.

> +	pm_runtime_use_autosuspend(dev->dev);
> +
>  	r = pm_runtime_get_sync(dev->dev);
>  	if (IS_ERR_VALUE(r))
>  		goto err_free_mem;
> @@ -1189,7 +1193,8 @@ omap_i2c_probe(struct platform_device *pdev)
>  
>  	of_i2c_register_devices(adap);
>  
> -	pm_runtime_put(dev->dev);
> +	pm_runtime_mark_last_busy(dev->dev);
> +	pm_runtime_put_autosuspend(dev->dev);
>  
>  	return 0;
>  
> -- 
> 1.7.12.rc0
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> 

[PATCH v3] i2c: omap: switch over to autosuspend API

[Felipe Balbi]

this helps us reduce unnecessary pm transitions
in case we have another i2c message starting soon.

Signed-off-by: Felipe Balbi <balbi@ti.com>
---
 drivers/i2c/busses/i2c-omap.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 60928f2..35e8207 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -55,6 +55,9 @@
 /* timeout waiting for the controller to respond */
 #define OMAP_I2C_TIMEOUT (msecs_to_jiffies(1000))
 
+/* timeout for pm runtime autosuspend */
+#define OMAP_I2C_PM_TIMEOUT		1000	/* ms */
+
 /* For OMAP3 I2C_IV has changed to I2C_WE (wakeup enable) */
 enum {
 	OMAP_I2C_REV_REG = 0,
@@ -645,7 +648,8 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
 
 	omap_i2c_wait_for_bb(dev);
 out:
-	pm_runtime_put(dev->dev);
+	pm_runtime_mark_last_busy(dev->dev);
+	pm_runtime_put_autosuspend(dev->dev);
 	return r;
 }
 
@@ -1113,6 +1117,9 @@ omap_i2c_probe(struct platform_device *pdev)
 		dev->regs = (u8 *)reg_map_ip_v1;
 
 	pm_runtime_enable(dev->dev);
+	pm_runtime_set_autosuspend_delay(dev->dev, OMAP_I2C_PM_TIMEOUT);
+	pm_runtime_use_autosuspend(dev->dev);
+
 	r = pm_runtime_get_sync(dev->dev);
 	if (IS_ERR_VALUE(r))
 		goto err_free_mem;
@@ -1189,7 +1196,8 @@ omap_i2c_probe(struct platform_device *pdev)
 
 	of_i2c_register_devices(adap);
 
-	pm_runtime_put(dev->dev);
+	pm_runtime_mark_last_busy(dev->dev);
+	pm_runtime_put_autosuspend(dev->dev);
 
 	return 0;
 
-- 
1.7.12.rc0

[PATCH v3] i2c: omap: switch over to autosuspend API

[Felipe Balbi]

this helps us reduce unnecessary pm transitions
in case we have another i2c message starting soon.

Signed-off-by: Felipe Balbi <balbi@ti.com>
---
 drivers/i2c/busses/i2c-omap.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 60928f2..35e8207 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -55,6 +55,9 @@
 /* timeout waiting for the controller to respond */
 #define OMAP_I2C_TIMEOUT (msecs_to_jiffies(1000))
 
+/* timeout for pm runtime autosuspend */
+#define OMAP_I2C_PM_TIMEOUT		1000	/* ms */
+
 /* For OMAP3 I2C_IV has changed to I2C_WE (wakeup enable) */
 enum {
 	OMAP_I2C_REV_REG = 0,
@@ -645,7 +648,8 @@ omap_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
 
 	omap_i2c_wait_for_bb(dev);
 out:
-	pm_runtime_put(dev->dev);
+	pm_runtime_mark_last_busy(dev->dev);
+	pm_runtime_put_autosuspend(dev->dev);
 	return r;
 }
 
@@ -1113,6 +1117,9 @@ omap_i2c_probe(struct platform_device *pdev)
 		dev->regs = (u8 *)reg_map_ip_v1;
 
 	pm_runtime_enable(dev->dev);
+	pm_runtime_set_autosuspend_delay(dev->dev, OMAP_I2C_PM_TIMEOUT);
+	pm_runtime_use_autosuspend(dev->dev);
+
 	r = pm_runtime_get_sync(dev->dev);
 	if (IS_ERR_VALUE(r))
 		goto err_free_mem;
@@ -1189,7 +1196,8 @@ omap_i2c_probe(struct platform_device *pdev)
 
 	of_i2c_register_devices(adap);
 
-	pm_runtime_put(dev->dev);
+	pm_runtime_mark_last_busy(dev->dev);
+	pm_runtime_put_autosuspend(dev->dev);
 
 	return 0;
 
-- 
1.7.12.rc0

RE: [PATCH v3] i2c: omap: switch over to autosuspend API

[Bedia, Vaibhav]

On Tue, Aug 07, 2012 at 18:08:07, Balbi, Felipe wrote:
> this helps us reduce unnecessary pm transitions
> in case we have another i2c message starting soon.
> 
> Signed-off-by: Felipe Balbi <balbi@ti.com>

FWIW, Acked-by: Vaibhav Bedia <vaibhav.bedia@ti.com> 

[PATCH v3] i2c: omap: switch over to autosuspend API

[Bedia, Vaibhav]

On Tue, Aug 07, 2012 at 18:08:07, Balbi, Felipe wrote:
> this helps us reduce unnecessary pm transitions
> in case we have another i2c message starting soon.
> 
> Signed-off-by: Felipe Balbi <balbi@ti.com>

FWIW, Acked-by: Vaibhav Bedia <vaibhav.bedia@ti.com> 

Re: [PATCH 0/4] i2c: omap: few more patches

[Shubhrajyoti]

On Monday 06 August 2012 07:48 PM, Felipe Balbi wrote:
> Just a few extra patches on top of the earlier series I sent.
>
> With these patches, we have threaded irq support and autosuspend support for
> i2c-omap driver.
Thanks for the patches.
>
> All patches boot tested with pandaboard.
Tested-by: Shubhrajyoti <shubhrajyoti@ti.com>

On omap4sdp and omap3sdp
also on omap3 did some basic power testing.
> Felipe Balbi (4):
>   i2c: omap: always return IRQ_HANDLED
>   i2c: omap: switch to threaded IRQ support
>   i2c: omap: remove unnecessary pm_runtime_suspended check
>   i2c: omap: switch over to autosuspend API
>
>  drivers/i2c/busses/i2c-omap.c | 53 ++++++++++++++++++++++++++++++++++---------
>  1 file changed, 42 insertions(+), 11 deletions(-)
>

[PATCH 0/4] i2c: omap: few more patches

[Shubhrajyoti]

On Monday 06 August 2012 07:48 PM, Felipe Balbi wrote:
> Just a few extra patches on top of the earlier series I sent.
>
> With these patches, we have threaded irq support and autosuspend support for
> i2c-omap driver.
Thanks for the patches.
>
> All patches boot tested with pandaboard.
Tested-by: Shubhrajyoti <shubhrajyoti@ti.com>

On omap4sdp and omap3sdp
also on omap3 did some basic power testing.
> Felipe Balbi (4):
>   i2c: omap: always return IRQ_HANDLED
>   i2c: omap: switch to threaded IRQ support
>   i2c: omap: remove unnecessary pm_runtime_suspended check
>   i2c: omap: switch over to autosuspend API
>
>  drivers/i2c/busses/i2c-omap.c | 53 ++++++++++++++++++++++++++++++++++---------
>  1 file changed, 42 insertions(+), 11 deletions(-)
>