From: Yijing Wang <wangyijing@huawei.com>
To: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>,
Andrew Vasquez <andrew.vasquez@qlogic.com>,
Dept-Eng Linux Driver <Linux-Driver@qlogic.com>,
"linux-scsi@vger.kernel.org" <linux-scsi@vger.kernel.org>,
PCI <linux-pci@vger.kernel.org>,
Saurav Kashyap <saurav.kashyap@qlogic.com>,
Chad Dupuis <chad.dupuis@qlogic.com>
Subject: Re: Fail to probe qla2xxx fiber channel card while doing pci hotplug
Date: Tue, 18 Sep 2012 09:26:32 +0800 [thread overview]
Message-ID: <5057CDC8.9030500@huawei.com> (raw)
In-Reply-To: <CC7CB653.20008%giridhar.malavali@qlogic.com>
On 2012/9/18 2:15, Giridhar Malavali wrote:
>
>
> On 9/17/12 5:06 AM, "Yijing Wang" <wangyijing@huawei.com> wrote:
>
>> [ 769.531289] qla2xxx [0000:08:00.0]-001d: : Found an ISP2532 irq 32
>> iobase 0xffffc90016bcc000.
>> [ 769.531748] qla2xxx 0000:08:00.0: irq 91 for MSI/MSI-X
>> [ 769.531768] qla2xxx 0000:08:00.0: irq 92 for MSI/MSI-X
>> [ 799.503673] qla2xxx [0000:08:00.0]-d008:10: No buffer available for
>> dump.
>> [ 799.503682] qla2xxx [0000:08:00.0]-101c:10: Mailbox cmd timeout
>> occurred, cmd=0xb, mb[0]=0xb, eeh_busy=0x0. Scheduling ISP abort.
>> [ 799.503689] qla2xxx [0000:08:00.0]-0098:10: Failed to load segment 0
>> of firmware.
>> [ 829.853242] qla2xxx [0000:08:00.0]-d008:10: No buffer available for
>> dump.
>> [ 829.853249] qla2xxx [0000:08:00.0]-008f:10: Failed to load segment 0
>> of firmware.
>> [ 829.853253] qla2xxx [0000:08:00.0]-00cf:10: Setup chip ****FAILED****.
>> [ 829.853258] qla2xxx [0000:08:00.0]-00d6:10: Failed to initialize
>> adapter - Adapter flags 2.
>> [ 829.853893] qla2xxx 0000:08:00.1: enabling device (0104 -> 0106)
>> [ 829.855251] qla2xxx [0000:08:00.1]-001d: : Found an ISP2532 irq 42
>> iobase 0xffffc90016b88000.
>> [ 829.855828] qla2xxx 0000:08:00.1: irq 91 for MSI/MSI-X
>> [ 829.855849] qla2xxx 0000:08:00.1: irq 92 for MSI/MSI-X
>> [ 859.827388] qla2xxx [0000:08:00.1]-d008:11: No buffer available for
>> dump.
>> [ 859.827395] qla2xxx [0000:08:00.1]-101c:11: Mailbox cmd timeout
>> occurred, cmd=0xb, mb[0]=0xb, eeh_busy=0x0. Scheduling ISP abort.
>> [ 859.827400] qla2xxx [0000:08:00.1]-0098:11: Failed to load segment 0
>> of firmware.
>> [ 890.176829] qla2xxx [0000:08:00.1]-d008:11: No buffer available for
>> dump.
>> [ 890.176837] qla2xxx [0000:08:00.1]-008f:11: Failed to load segment 0
>> of firmware.
>> [ 890.176841] qla2xxx [0000:08:00.1]-00cf:11: Setup chip ****FAILED****.
>> [ 890.176845] qla2xxx [0000:08:00.1]-00d6:11: Failed to initialize
>> adapter - Adapter flags 2.
>
> I see that the one of the initial mailbox which loads data from system
> memory to RISC RAM failing causing the probe to fail.
>
> -- Giri
>
Hi Giri,
Thanks for your comments very much!
Because I hot-add FC card in empty slot is ok, so I think maybe FC card and driver have no problem(I'm not sure).
So I want to know what hardware(or other) problem may result mailbox loads data from system memory to RISC RAM fail?
Thanks
Yijing
>
>
>
> .
>
--
Thanks!
Yijing
next prev parent reply other threads:[~2012-09-18 1:27 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-09-15 10:22 Fail to probe qla2xxx fiber channel card while doing pci hotplug Yijing Wang
2012-09-15 10:22 ` Yijing Wang
2012-09-16 3:30 ` Bjorn Helgaas
2012-09-17 12:06 ` Yijing Wang
2012-09-17 18:15 ` Giridhar Malavali
2012-09-18 1:26 ` Yijing Wang [this message]
2012-09-18 17:54 ` Bjorn Helgaas
2012-09-18 23:49 ` Giridhar Malavali
2012-09-20 1:27 ` Yijing Wang
2012-09-19 1:50 ` Yijing Wang
2012-09-19 1:50 ` Yijing Wang
2012-09-19 13:39 ` Bjorn Helgaas
2012-09-19 15:31 ` Jiang Liu
2012-09-20 1:39 ` Yijing Wang
2012-09-20 1:39 ` Yijing Wang
2012-09-20 1:47 ` Yijing Wang
2012-09-20 1:47 ` Yijing Wang
2012-09-20 12:26 ` Yijing Wang
2012-09-20 12:26 ` Yijing Wang
2012-09-20 15:46 ` Bjorn Helgaas
2012-09-20 15:58 ` Jiang Liu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5057CDC8.9030500@huawei.com \
--to=wangyijing@huawei.com \
--cc=Linux-Driver@qlogic.com \
--cc=andrew.vasquez@qlogic.com \
--cc=bhelgaas@google.com \
--cc=chad.dupuis@qlogic.com \
--cc=giridhar.malavali@qlogic.com \
--cc=linux-pci@vger.kernel.org \
--cc=linux-scsi@vger.kernel.org \
--cc=saurav.kashyap@qlogic.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.