Re: [PATCH 3/4] Enable ecc-mode selection in the driver

Re: [PATCH 3/4] Enable ecc-mode selection in the driver

[Jason Cooper]

Stefan,

This is a good-looking patch series, nice and small!  A few comments:

On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
> In order to be able to use the ecc-mode, add the bch module to the default
> settings for the kirwood boards and enable the activation in orin-nand.c

s/orin-nand/orion-nand/

> 
> Signed-off-by: Stefan Peter <s.peter@mpl.ch>
> ---
> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
> index 93f3794..4a9d3f7 100644
> --- a/arch/arm/configs/kirkwood_defconfig
> +++ b/arch/arm/configs/kirkwood_defconfig
> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
>  CONFIG_MTD_PHYSMAP=y
>  CONFIG_MTD_M25P80=y
>  CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_ECC_BCH=y
>  CONFIG_MTD_NAND_ORION=y
>  CONFIG_BLK_DEV_LOOP=y
>  # CONFIG_SCSI_PROC_FS is not set

Please make the defconfig change a separate patch.

As a general note (this series shouldn't be a problem), please sort the
series so that you add the driver feature first, then enable it in
defconfig, then use it in DT.  This way, a future bisection won't run
into any nasty surprises, other than what they're looking for. ;-)

thx,

Jason.

Re: [PATCH 3/4] Enable ecc-mode selection in the driver

[Jason Cooper]

Stefan,

This is a good-looking patch series, nice and small!  A few comments:

On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
> In order to be able to use the ecc-mode, add the bch module to the default
> settings for the kirwood boards and enable the activation in orin-nand.c

s/orin-nand/orion-nand/

> 
> Signed-off-by: Stefan Peter <s.peter@mpl.ch>
> ---
> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
> index 93f3794..4a9d3f7 100644
> --- a/arch/arm/configs/kirkwood_defconfig
> +++ b/arch/arm/configs/kirkwood_defconfig
> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
>  CONFIG_MTD_PHYSMAP=y
>  CONFIG_MTD_M25P80=y
>  CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_ECC_BCH=y
>  CONFIG_MTD_NAND_ORION=y
>  CONFIG_BLK_DEV_LOOP=y
>  # CONFIG_SCSI_PROC_FS is not set

Please make the defconfig change a separate patch.

As a general note (this series shouldn't be a problem), please sort the
series so that you add the driver feature first, then enable it in
defconfig, then use it in DT.  This way, a future bisection won't run
into any nasty surprises, other than what they're looking for. ;-)

thx,

Jason.

Re: [PATCH 3/4] Enable ecc-mode selection in the driver

[Jason Cooper]

Stefan,

This is a good-looking patch series, nice and small!  A few comments:

On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
> In order to be able to use the ecc-mode, add the bch module to the default
> settings for the kirwood boards and enable the activation in orin-nand.c

s/orin-nand/orion-nand/

> 
> Signed-off-by: Stefan Peter <s.peter-R0yVo0h44Ow@public.gmane.org>
> ---
> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
> index 93f3794..4a9d3f7 100644
> --- a/arch/arm/configs/kirkwood_defconfig
> +++ b/arch/arm/configs/kirkwood_defconfig
> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
>  CONFIG_MTD_PHYSMAP=y
>  CONFIG_MTD_M25P80=y
>  CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_ECC_BCH=y
>  CONFIG_MTD_NAND_ORION=y
>  CONFIG_BLK_DEV_LOOP=y
>  # CONFIG_SCSI_PROC_FS is not set

Please make the defconfig change a separate patch.

As a general note (this series shouldn't be a problem), please sort the
series so that you add the driver feature first, then enable it in
defconfig, then use it in DT.  This way, a future bisection won't run
into any nasty surprises, other than what they're looking for. ;-)

thx,

Jason.

[PATCH 3/4] Enable ecc-mode selection in the driver

[Jason Cooper]

Stefan,

This is a good-looking patch series, nice and small!  A few comments:

On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
> In order to be able to use the ecc-mode, add the bch module to the default
> settings for the kirwood boards and enable the activation in orin-nand.c

s/orin-nand/orion-nand/

> 
> Signed-off-by: Stefan Peter <s.peter@mpl.ch>
> ---
> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
> index 93f3794..4a9d3f7 100644
> --- a/arch/arm/configs/kirkwood_defconfig
> +++ b/arch/arm/configs/kirkwood_defconfig
> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
>  CONFIG_MTD_PHYSMAP=y
>  CONFIG_MTD_M25P80=y
>  CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_ECC_BCH=y
>  CONFIG_MTD_NAND_ORION=y
>  CONFIG_BLK_DEV_LOOP=y
>  # CONFIG_SCSI_PROC_FS is not set

Please make the defconfig change a separate patch.

As a general note (this series shouldn't be a problem), please sort the
series so that you add the driver feature first, then enable it in
defconfig, then use it in DT.  This way, a future bisection won't run
into any nasty surprises, other than what they're looking for. ;-)

thx,

Jason.

Re: [PATCH 3/4] Enable ecc-mode selection in the driver

[Stefan Peter]

Hi Jason

on 15.01.2013 13:33, Jason Cooper wrote:
> Stefan,
> 
> This is a good-looking patch series, nice and small!  A few comments:
> 
> On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
>> In order to be able to use the ecc-mode, add the bch module to the default
>> settings for the kirwood boards and enable the activation in orin-nand.c
> 
> s/orin-nand/orion-nand/

Will fix.

> 
>>
>> Signed-off-by: Stefan Peter <s.peter@mpl.ch>
>> ---
>> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
>> index 93f3794..4a9d3f7 100644
>> --- a/arch/arm/configs/kirkwood_defconfig
>> +++ b/arch/arm/configs/kirkwood_defconfig
>> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
>>  CONFIG_MTD_PHYSMAP=y
>>  CONFIG_MTD_M25P80=y
>>  CONFIG_MTD_NAND=y
>> +CONFIG_MTD_NAND_ECC_BCH=y
>>  CONFIG_MTD_NAND_ORION=y
>>  CONFIG_BLK_DEV_LOOP=y
>>  # CONFIG_SCSI_PROC_FS is not set
> 
> Please make the defconfig change a separate patch.

Will do.

> 
> As a general note (this series shouldn't be a problem), please sort the
> series so that you add the driver feature first, then enable it in
> defconfig, then use it in DT.  This way, a future bisection won't run
> into any nasty surprises, other than what they're looking for. ;-)

Will do.

Thank you very much for your review.

Stefan Peter
-- 
MPL AG, Switzerland                     http://www.mpl.ch
Tel. +41 (0)56 483 34 34          Fax: +41(0)56 493 30 20

Re: [PATCH 3/4] Enable ecc-mode selection in the driver

[Stefan Peter]

Hi Jason

on 15.01.2013 13:33, Jason Cooper wrote:
> Stefan,
> 
> This is a good-looking patch series, nice and small!  A few comments:
> 
> On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
>> In order to be able to use the ecc-mode, add the bch module to the default
>> settings for the kirwood boards and enable the activation in orin-nand.c
> 
> s/orin-nand/orion-nand/

Will fix.

> 
>>
>> Signed-off-by: Stefan Peter <s.peter@mpl.ch>
>> ---
>> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
>> index 93f3794..4a9d3f7 100644
>> --- a/arch/arm/configs/kirkwood_defconfig
>> +++ b/arch/arm/configs/kirkwood_defconfig
>> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
>>  CONFIG_MTD_PHYSMAP=y
>>  CONFIG_MTD_M25P80=y
>>  CONFIG_MTD_NAND=y
>> +CONFIG_MTD_NAND_ECC_BCH=y
>>  CONFIG_MTD_NAND_ORION=y
>>  CONFIG_BLK_DEV_LOOP=y
>>  # CONFIG_SCSI_PROC_FS is not set
> 
> Please make the defconfig change a separate patch.

Will do.

> 
> As a general note (this series shouldn't be a problem), please sort the
> series so that you add the driver feature first, then enable it in
> defconfig, then use it in DT.  This way, a future bisection won't run
> into any nasty surprises, other than what they're looking for. ;-)

Will do.

Thank you very much for your review.

Stefan Peter
-- 
MPL AG, Switzerland                     http://www.mpl.ch
Tel. +41 (0)56 483 34 34          Fax: +41(0)56 493 30 20

Re: [PATCH 3/4] Enable ecc-mode selection in the driver

[Stefan Peter]

Hi Jason

on 15.01.2013 13:33, Jason Cooper wrote:
> Stefan,
> 
> This is a good-looking patch series, nice and small!  A few comments:
> 
> On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
>> In order to be able to use the ecc-mode, add the bch module to the default
>> settings for the kirwood boards and enable the activation in orin-nand.c
> 
> s/orin-nand/orion-nand/

Will fix.

> 
>>
>> Signed-off-by: Stefan Peter <s.peter-R0yVo0h44Ow@public.gmane.org>
>> ---
>> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
>> index 93f3794..4a9d3f7 100644
>> --- a/arch/arm/configs/kirkwood_defconfig
>> +++ b/arch/arm/configs/kirkwood_defconfig
>> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
>>  CONFIG_MTD_PHYSMAP=y
>>  CONFIG_MTD_M25P80=y
>>  CONFIG_MTD_NAND=y
>> +CONFIG_MTD_NAND_ECC_BCH=y
>>  CONFIG_MTD_NAND_ORION=y
>>  CONFIG_BLK_DEV_LOOP=y
>>  # CONFIG_SCSI_PROC_FS is not set
> 
> Please make the defconfig change a separate patch.

Will do.

> 
> As a general note (this series shouldn't be a problem), please sort the
> series so that you add the driver feature first, then enable it in
> defconfig, then use it in DT.  This way, a future bisection won't run
> into any nasty surprises, other than what they're looking for. ;-)

Will do.

Thank you very much for your review.

Stefan Peter
-- 
MPL AG, Switzerland                     http://www.mpl.ch
Tel. +41 (0)56 483 34 34          Fax: +41(0)56 493 30 20

[PATCH 3/4] Enable ecc-mode selection in the driver

[Stefan Peter]

Hi Jason

on 15.01.2013 13:33, Jason Cooper wrote:
> Stefan,
> 
> This is a good-looking patch series, nice and small!  A few comments:
> 
> On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
>> In order to be able to use the ecc-mode, add the bch module to the default
>> settings for the kirwood boards and enable the activation in orin-nand.c
> 
> s/orin-nand/orion-nand/

Will fix.

> 
>>
>> Signed-off-by: Stefan Peter <s.peter@mpl.ch>
>> ---
>> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
>> index 93f3794..4a9d3f7 100644
>> --- a/arch/arm/configs/kirkwood_defconfig
>> +++ b/arch/arm/configs/kirkwood_defconfig
>> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
>>  CONFIG_MTD_PHYSMAP=y
>>  CONFIG_MTD_M25P80=y
>>  CONFIG_MTD_NAND=y
>> +CONFIG_MTD_NAND_ECC_BCH=y
>>  CONFIG_MTD_NAND_ORION=y
>>  CONFIG_BLK_DEV_LOOP=y
>>  # CONFIG_SCSI_PROC_FS is not set
> 
> Please make the defconfig change a separate patch.

Will do.

> 
> As a general note (this series shouldn't be a problem), please sort the
> series so that you add the driver feature first, then enable it in
> defconfig, then use it in DT.  This way, a future bisection won't run
> into any nasty surprises, other than what they're looking for. ;-)

Will do.

Thank you very much for your review.

Stefan Peter
-- 
MPL AG, Switzerland                     http://www.mpl.ch
Tel. +41 (0)56 483 34 34          Fax: +41(0)56 493 30 20

Re: [PATCH 3/4] Enable ecc-mode selection in the driver

[Andrew Lunn]

On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
> In order to be able to use the ecc-mode, add the bch module to the default
> settings for the kirwood boards and enable the activation in orin-nand.c
> 
> Signed-off-by: Stefan Peter <s.peter@mpl.ch>
> ---
> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
> index 93f3794..4a9d3f7 100644
> --- a/arch/arm/configs/kirkwood_defconfig
> +++ b/arch/arm/configs/kirkwood_defconfig
> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
>  CONFIG_MTD_PHYSMAP=y
>  CONFIG_MTD_M25P80=y
>  CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_ECC_BCH=y
>  CONFIG_MTD_NAND_ORION=y
>  CONFIG_BLK_DEV_LOOP=y
>  # CONFIG_SCSI_PROC_FS is not set
> diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c
> index cd72b92..1a35257 100644
> --- a/drivers/mtd/nand/orion_nand.c
> +++ b/drivers/mtd/nand/orion_nand.c
> @@ -14,6 +14,7 @@
>  #include <linux/module.h>
>  #include <linux/platform_device.h>
>  #include <linux/of.h>
> +#include <linux/of_mtd.h>
>  #include <linux/mtd/mtd.h>
>  #include <linux/mtd/nand.h>
>  #include <linux/mtd/partitions.h>
> @@ -130,6 +131,7 @@ static int __init orion_nand_probe(struct platform_device *pdev)
>  		if (!of_property_read_u32(pdev->dev.of_node,
>  						"chip-delay", &val))
>  			board->chip_delay = (u8)val;
> +		board->ecc_mode = of_get_nand_ecc_mode(pdev->dev.of_node);

>  	} else
>  		board = pdev->dev.platform_data;
>  
> @@ -140,7 +142,8 @@ static int __init orion_nand_probe(struct platform_device *pdev)
>  	nc->IO_ADDR_R = nc->IO_ADDR_W = io_base;
>  	nc->cmd_ctrl = orion_nand_cmd_ctrl;
>  	nc->read_buf = orion_nand_read_buf;
> -	nc->ecc.mode = NAND_ECC_SOFT;
> +	nc->ecc.mode = board->ecc_mode == NAND_ECC_SOFT_BCH ?
> +		NAND_ECC_SOFT_BCH : NAND_ECC_SOFT;

Hi Stefan

What about a user that wants one of the other valid values?
NAND_ECC_OOB_FIRST, NAND_ECC_HW_SYNDROME, etc.

Would:

	if (IS_ERR(board->ecc_mode)) {
		nc->ecc.mode = NAND_ECC_SOFT;
		dev_info(&pdev->dev, "Defaulting to NAND_ECC_SOFT");
	} else
		nc->ecc.mode = board->ecc_mode

be better?

   Andrew

Re: [PATCH 3/4] Enable ecc-mode selection in the driver

[Andrew Lunn]

On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
> In order to be able to use the ecc-mode, add the bch module to the default
> settings for the kirwood boards and enable the activation in orin-nand.c
> 
> Signed-off-by: Stefan Peter <s.peter@mpl.ch>
> ---
> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
> index 93f3794..4a9d3f7 100644
> --- a/arch/arm/configs/kirkwood_defconfig
> +++ b/arch/arm/configs/kirkwood_defconfig
> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
>  CONFIG_MTD_PHYSMAP=y
>  CONFIG_MTD_M25P80=y
>  CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_ECC_BCH=y
>  CONFIG_MTD_NAND_ORION=y
>  CONFIG_BLK_DEV_LOOP=y
>  # CONFIG_SCSI_PROC_FS is not set
> diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c
> index cd72b92..1a35257 100644
> --- a/drivers/mtd/nand/orion_nand.c
> +++ b/drivers/mtd/nand/orion_nand.c
> @@ -14,6 +14,7 @@
>  #include <linux/module.h>
>  #include <linux/platform_device.h>
>  #include <linux/of.h>
> +#include <linux/of_mtd.h>
>  #include <linux/mtd/mtd.h>
>  #include <linux/mtd/nand.h>
>  #include <linux/mtd/partitions.h>
> @@ -130,6 +131,7 @@ static int __init orion_nand_probe(struct platform_device *pdev)
>  		if (!of_property_read_u32(pdev->dev.of_node,
>  						"chip-delay", &val))
>  			board->chip_delay = (u8)val;
> +		board->ecc_mode = of_get_nand_ecc_mode(pdev->dev.of_node);

>  	} else
>  		board = pdev->dev.platform_data;
>  
> @@ -140,7 +142,8 @@ static int __init orion_nand_probe(struct platform_device *pdev)
>  	nc->IO_ADDR_R = nc->IO_ADDR_W = io_base;
>  	nc->cmd_ctrl = orion_nand_cmd_ctrl;
>  	nc->read_buf = orion_nand_read_buf;
> -	nc->ecc.mode = NAND_ECC_SOFT;
> +	nc->ecc.mode = board->ecc_mode == NAND_ECC_SOFT_BCH ?
> +		NAND_ECC_SOFT_BCH : NAND_ECC_SOFT;

Hi Stefan

What about a user that wants one of the other valid values?
NAND_ECC_OOB_FIRST, NAND_ECC_HW_SYNDROME, etc.

Would:

	if (IS_ERR(board->ecc_mode)) {
		nc->ecc.mode = NAND_ECC_SOFT;
		dev_info(&pdev->dev, "Defaulting to NAND_ECC_SOFT");
	} else
		nc->ecc.mode = board->ecc_mode

be better?

   Andrew

Re: [PATCH 3/4] Enable ecc-mode selection in the driver

[Andrew Lunn]

On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
> In order to be able to use the ecc-mode, add the bch module to the default
> settings for the kirwood boards and enable the activation in orin-nand.c
> 
> Signed-off-by: Stefan Peter <s.peter-R0yVo0h44Ow@public.gmane.org>
> ---
> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
> index 93f3794..4a9d3f7 100644
> --- a/arch/arm/configs/kirkwood_defconfig
> +++ b/arch/arm/configs/kirkwood_defconfig
> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
>  CONFIG_MTD_PHYSMAP=y
>  CONFIG_MTD_M25P80=y
>  CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_ECC_BCH=y
>  CONFIG_MTD_NAND_ORION=y
>  CONFIG_BLK_DEV_LOOP=y
>  # CONFIG_SCSI_PROC_FS is not set
> diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c
> index cd72b92..1a35257 100644
> --- a/drivers/mtd/nand/orion_nand.c
> +++ b/drivers/mtd/nand/orion_nand.c
> @@ -14,6 +14,7 @@
>  #include <linux/module.h>
>  #include <linux/platform_device.h>
>  #include <linux/of.h>
> +#include <linux/of_mtd.h>
>  #include <linux/mtd/mtd.h>
>  #include <linux/mtd/nand.h>
>  #include <linux/mtd/partitions.h>
> @@ -130,6 +131,7 @@ static int __init orion_nand_probe(struct platform_device *pdev)
>  		if (!of_property_read_u32(pdev->dev.of_node,
>  						"chip-delay", &val))
>  			board->chip_delay = (u8)val;
> +		board->ecc_mode = of_get_nand_ecc_mode(pdev->dev.of_node);

>  	} else
>  		board = pdev->dev.platform_data;
>  
> @@ -140,7 +142,8 @@ static int __init orion_nand_probe(struct platform_device *pdev)
>  	nc->IO_ADDR_R = nc->IO_ADDR_W = io_base;
>  	nc->cmd_ctrl = orion_nand_cmd_ctrl;
>  	nc->read_buf = orion_nand_read_buf;
> -	nc->ecc.mode = NAND_ECC_SOFT;
> +	nc->ecc.mode = board->ecc_mode == NAND_ECC_SOFT_BCH ?
> +		NAND_ECC_SOFT_BCH : NAND_ECC_SOFT;

Hi Stefan

What about a user that wants one of the other valid values?
NAND_ECC_OOB_FIRST, NAND_ECC_HW_SYNDROME, etc.

Would:

	if (IS_ERR(board->ecc_mode)) {
		nc->ecc.mode = NAND_ECC_SOFT;
		dev_info(&pdev->dev, "Defaulting to NAND_ECC_SOFT");
	} else
		nc->ecc.mode = board->ecc_mode

be better?

   Andrew

[PATCH 3/4] Enable ecc-mode selection in the driver

[Andrew Lunn]

On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
> In order to be able to use the ecc-mode, add the bch module to the default
> settings for the kirwood boards and enable the activation in orin-nand.c
> 
> Signed-off-by: Stefan Peter <s.peter@mpl.ch>
> ---
> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
> index 93f3794..4a9d3f7 100644
> --- a/arch/arm/configs/kirkwood_defconfig
> +++ b/arch/arm/configs/kirkwood_defconfig
> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
>  CONFIG_MTD_PHYSMAP=y
>  CONFIG_MTD_M25P80=y
>  CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_ECC_BCH=y
>  CONFIG_MTD_NAND_ORION=y
>  CONFIG_BLK_DEV_LOOP=y
>  # CONFIG_SCSI_PROC_FS is not set
> diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c
> index cd72b92..1a35257 100644
> --- a/drivers/mtd/nand/orion_nand.c
> +++ b/drivers/mtd/nand/orion_nand.c
> @@ -14,6 +14,7 @@
>  #include <linux/module.h>
>  #include <linux/platform_device.h>
>  #include <linux/of.h>
> +#include <linux/of_mtd.h>
>  #include <linux/mtd/mtd.h>
>  #include <linux/mtd/nand.h>
>  #include <linux/mtd/partitions.h>
> @@ -130,6 +131,7 @@ static int __init orion_nand_probe(struct platform_device *pdev)
>  		if (!of_property_read_u32(pdev->dev.of_node,
>  						"chip-delay", &val))
>  			board->chip_delay = (u8)val;
> +		board->ecc_mode = of_get_nand_ecc_mode(pdev->dev.of_node);

>  	} else
>  		board = pdev->dev.platform_data;
>  
> @@ -140,7 +142,8 @@ static int __init orion_nand_probe(struct platform_device *pdev)
>  	nc->IO_ADDR_R = nc->IO_ADDR_W = io_base;
>  	nc->cmd_ctrl = orion_nand_cmd_ctrl;
>  	nc->read_buf = orion_nand_read_buf;
> -	nc->ecc.mode = NAND_ECC_SOFT;
> +	nc->ecc.mode = board->ecc_mode == NAND_ECC_SOFT_BCH ?
> +		NAND_ECC_SOFT_BCH : NAND_ECC_SOFT;

Hi Stefan

What about a user that wants one of the other valid values?
NAND_ECC_OOB_FIRST, NAND_ECC_HW_SYNDROME, etc.

Would:

	if (IS_ERR(board->ecc_mode)) {
		nc->ecc.mode = NAND_ECC_SOFT;
		dev_info(&pdev->dev, "Defaulting to NAND_ECC_SOFT");
	} else
		nc->ecc.mode = board->ecc_mode

be better?

   Andrew

Re: [PATCH 3/4] Enable ecc-mode selection in the driver

[Stefan Peter]

Hi Andrew

on 15.01.2013 13:51, Andrew Lunn wrote:
> On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
>> In order to be able to use the ecc-mode, add the bch module to the default
>> settings for the kirwood boards and enable the activation in orin-nand.c
>>
>> Signed-off-by: Stefan Peter <s.peter@mpl.ch>
>> ---
>> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
>> index 93f3794..4a9d3f7 100644
>> --- a/arch/arm/configs/kirkwood_defconfig
>> +++ b/arch/arm/configs/kirkwood_defconfig
>> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
>>  CONFIG_MTD_PHYSMAP=y
>>  CONFIG_MTD_M25P80=y
>>  CONFIG_MTD_NAND=y
>> +CONFIG_MTD_NAND_ECC_BCH=y
>>  CONFIG_MTD_NAND_ORION=y
>>  CONFIG_BLK_DEV_LOOP=y
>>  # CONFIG_SCSI_PROC_FS is not set
>> diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c
>> index cd72b92..1a35257 100644
>> --- a/drivers/mtd/nand/orion_nand.c
>> +++ b/drivers/mtd/nand/orion_nand.c
>> @@ -14,6 +14,7 @@
>>  #include <linux/module.h>
>>  #include <linux/platform_device.h>
>>  #include <linux/of.h>
>> +#include <linux/of_mtd.h>
>>  #include <linux/mtd/mtd.h>
>>  #include <linux/mtd/nand.h>
>>  #include <linux/mtd/partitions.h>
>> @@ -130,6 +131,7 @@ static int __init orion_nand_probe(struct platform_device *pdev)
>>  		if (!of_property_read_u32(pdev->dev.of_node,
>>  						"chip-delay", &val))
>>  			board->chip_delay = (u8)val;
>> +		board->ecc_mode = of_get_nand_ecc_mode(pdev->dev.of_node);
> 
>>  	} else
>>  		board = pdev->dev.platform_data;
>>  
>> @@ -140,7 +142,8 @@ static int __init orion_nand_probe(struct platform_device *pdev)
>>  	nc->IO_ADDR_R = nc->IO_ADDR_W = io_base;
>>  	nc->cmd_ctrl = orion_nand_cmd_ctrl;
>>  	nc->read_buf = orion_nand_read_buf;
>> -	nc->ecc.mode = NAND_ECC_SOFT;
>> +	nc->ecc.mode = board->ecc_mode == NAND_ECC_SOFT_BCH ?
>> +		NAND_ECC_SOFT_BCH : NAND_ECC_SOFT;
> 
> Hi Stefan
> 
> What about a user that wants one of the other valid values?
> NAND_ECC_OOB_FIRST, NAND_ECC_HW_SYNDROME, etc.

As far as I understand, NAND_ECC_NONE, NAND_ECC_SOFT and
NAND_ECC_SOFT_BCH are the only ECC modes that do not require
corresponding hardware support which is missing in the marvell
88F6180/88F619x/88F628x. From my point of view, NAND_ECC_NONE does not
make sense, too, because MLC NAND Flash requires ECC to be usable.

> 
> Would:
> 
> 	if (IS_ERR(board->ecc_mode)) {
> 		nc->ecc.mode = NAND_ECC_SOFT;
> 		dev_info(&pdev->dev, "Defaulting to NAND_ECC_SOFT");
> 	} else
> 		nc->ecc.mode = board->ecc_mode
> 
> be better?

I feel safer by limiting the modes to what I could test.

Regards

Stefan Peter


-- 
MPL AG, Switzerland                     http://www.mpl.ch
Tel. +41 (0)56 483 34 34          Fax: +41(0)56 493 30 20

Re: [PATCH 3/4] Enable ecc-mode selection in the driver

[Stefan Peter]

Hi Andrew

on 15.01.2013 13:51, Andrew Lunn wrote:
> On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
>> In order to be able to use the ecc-mode, add the bch module to the default
>> settings for the kirwood boards and enable the activation in orin-nand.c
>>
>> Signed-off-by: Stefan Peter <s.peter@mpl.ch>
>> ---
>> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
>> index 93f3794..4a9d3f7 100644
>> --- a/arch/arm/configs/kirkwood_defconfig
>> +++ b/arch/arm/configs/kirkwood_defconfig
>> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
>>  CONFIG_MTD_PHYSMAP=y
>>  CONFIG_MTD_M25P80=y
>>  CONFIG_MTD_NAND=y
>> +CONFIG_MTD_NAND_ECC_BCH=y
>>  CONFIG_MTD_NAND_ORION=y
>>  CONFIG_BLK_DEV_LOOP=y
>>  # CONFIG_SCSI_PROC_FS is not set
>> diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c
>> index cd72b92..1a35257 100644
>> --- a/drivers/mtd/nand/orion_nand.c
>> +++ b/drivers/mtd/nand/orion_nand.c
>> @@ -14,6 +14,7 @@
>>  #include <linux/module.h>
>>  #include <linux/platform_device.h>
>>  #include <linux/of.h>
>> +#include <linux/of_mtd.h>
>>  #include <linux/mtd/mtd.h>
>>  #include <linux/mtd/nand.h>
>>  #include <linux/mtd/partitions.h>
>> @@ -130,6 +131,7 @@ static int __init orion_nand_probe(struct platform_device *pdev)
>>  		if (!of_property_read_u32(pdev->dev.of_node,
>>  						"chip-delay", &val))
>>  			board->chip_delay = (u8)val;
>> +		board->ecc_mode = of_get_nand_ecc_mode(pdev->dev.of_node);
> 
>>  	} else
>>  		board = pdev->dev.platform_data;
>>  
>> @@ -140,7 +142,8 @@ static int __init orion_nand_probe(struct platform_device *pdev)
>>  	nc->IO_ADDR_R = nc->IO_ADDR_W = io_base;
>>  	nc->cmd_ctrl = orion_nand_cmd_ctrl;
>>  	nc->read_buf = orion_nand_read_buf;
>> -	nc->ecc.mode = NAND_ECC_SOFT;
>> +	nc->ecc.mode = board->ecc_mode == NAND_ECC_SOFT_BCH ?
>> +		NAND_ECC_SOFT_BCH : NAND_ECC_SOFT;
> 
> Hi Stefan
> 
> What about a user that wants one of the other valid values?
> NAND_ECC_OOB_FIRST, NAND_ECC_HW_SYNDROME, etc.

As far as I understand, NAND_ECC_NONE, NAND_ECC_SOFT and
NAND_ECC_SOFT_BCH are the only ECC modes that do not require
corresponding hardware support which is missing in the marvell
88F6180/88F619x/88F628x. From my point of view, NAND_ECC_NONE does not
make sense, too, because MLC NAND Flash requires ECC to be usable.

> 
> Would:
> 
> 	if (IS_ERR(board->ecc_mode)) {
> 		nc->ecc.mode = NAND_ECC_SOFT;
> 		dev_info(&pdev->dev, "Defaulting to NAND_ECC_SOFT");
> 	} else
> 		nc->ecc.mode = board->ecc_mode
> 
> be better?

I feel safer by limiting the modes to what I could test.

Regards

Stefan Peter


-- 
MPL AG, Switzerland                     http://www.mpl.ch
Tel. +41 (0)56 483 34 34          Fax: +41(0)56 493 30 20

[PATCH 3/4] Enable ecc-mode selection in the driver

[Stefan Peter]

Hi Andrew

on 15.01.2013 13:51, Andrew Lunn wrote:
> On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
>> In order to be able to use the ecc-mode, add the bch module to the default
>> settings for the kirwood boards and enable the activation in orin-nand.c
>>
>> Signed-off-by: Stefan Peter <s.peter@mpl.ch>
>> ---
>> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
>> index 93f3794..4a9d3f7 100644
>> --- a/arch/arm/configs/kirkwood_defconfig
>> +++ b/arch/arm/configs/kirkwood_defconfig
>> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
>>  CONFIG_MTD_PHYSMAP=y
>>  CONFIG_MTD_M25P80=y
>>  CONFIG_MTD_NAND=y
>> +CONFIG_MTD_NAND_ECC_BCH=y
>>  CONFIG_MTD_NAND_ORION=y
>>  CONFIG_BLK_DEV_LOOP=y
>>  # CONFIG_SCSI_PROC_FS is not set
>> diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c
>> index cd72b92..1a35257 100644
>> --- a/drivers/mtd/nand/orion_nand.c
>> +++ b/drivers/mtd/nand/orion_nand.c
>> @@ -14,6 +14,7 @@
>>  #include <linux/module.h>
>>  #include <linux/platform_device.h>
>>  #include <linux/of.h>
>> +#include <linux/of_mtd.h>
>>  #include <linux/mtd/mtd.h>
>>  #include <linux/mtd/nand.h>
>>  #include <linux/mtd/partitions.h>
>> @@ -130,6 +131,7 @@ static int __init orion_nand_probe(struct platform_device *pdev)
>>  		if (!of_property_read_u32(pdev->dev.of_node,
>>  						"chip-delay", &val))
>>  			board->chip_delay = (u8)val;
>> +		board->ecc_mode = of_get_nand_ecc_mode(pdev->dev.of_node);
> 
>>  	} else
>>  		board = pdev->dev.platform_data;
>>  
>> @@ -140,7 +142,8 @@ static int __init orion_nand_probe(struct platform_device *pdev)
>>  	nc->IO_ADDR_R = nc->IO_ADDR_W = io_base;
>>  	nc->cmd_ctrl = orion_nand_cmd_ctrl;
>>  	nc->read_buf = orion_nand_read_buf;
>> -	nc->ecc.mode = NAND_ECC_SOFT;
>> +	nc->ecc.mode = board->ecc_mode == NAND_ECC_SOFT_BCH ?
>> +		NAND_ECC_SOFT_BCH : NAND_ECC_SOFT;
> 
> Hi Stefan
> 
> What about a user that wants one of the other valid values?
> NAND_ECC_OOB_FIRST, NAND_ECC_HW_SYNDROME, etc.

As far as I understand, NAND_ECC_NONE, NAND_ECC_SOFT and
NAND_ECC_SOFT_BCH are the only ECC modes that do not require
corresponding hardware support which is missing in the marvell
88F6180/88F619x/88F628x. From my point of view, NAND_ECC_NONE does not
make sense, too, because MLC NAND Flash requires ECC to be usable.

> 
> Would:
> 
> 	if (IS_ERR(board->ecc_mode)) {
> 		nc->ecc.mode = NAND_ECC_SOFT;
> 		dev_info(&pdev->dev, "Defaulting to NAND_ECC_SOFT");
> 	} else
> 		nc->ecc.mode = board->ecc_mode
> 
> be better?

I feel safer by limiting the modes to what I could test.

Regards

Stefan Peter


-- 
MPL AG, Switzerland                     http://www.mpl.ch
Tel. +41 (0)56 483 34 34          Fax: +41(0)56 493 30 20

Re: [PATCH 3/4] Enable ecc-mode selection in the driver

[Andrew Lunn]

On Wed, Jan 16, 2013 at 12:43:57PM +0100, Stefan Peter wrote:
> Hi Andrew
> 
> on 15.01.2013 13:51, Andrew Lunn wrote:
> > On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
> >> In order to be able to use the ecc-mode, add the bch module to the default
> >> settings for the kirwood boards and enable the activation in orin-nand.c
> >>
> >> Signed-off-by: Stefan Peter <s.peter@mpl.ch>
> >> ---
> >> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
> >> index 93f3794..4a9d3f7 100644
> >> --- a/arch/arm/configs/kirkwood_defconfig
> >> +++ b/arch/arm/configs/kirkwood_defconfig
> >> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
> >>  CONFIG_MTD_PHYSMAP=y
> >>  CONFIG_MTD_M25P80=y
> >>  CONFIG_MTD_NAND=y
> >> +CONFIG_MTD_NAND_ECC_BCH=y
> >>  CONFIG_MTD_NAND_ORION=y
> >>  CONFIG_BLK_DEV_LOOP=y
> >>  # CONFIG_SCSI_PROC_FS is not set
> >> diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c
> >> index cd72b92..1a35257 100644
> >> --- a/drivers/mtd/nand/orion_nand.c
> >> +++ b/drivers/mtd/nand/orion_nand.c
> >> @@ -14,6 +14,7 @@
> >>  #include <linux/module.h>
> >>  #include <linux/platform_device.h>
> >>  #include <linux/of.h>
> >> +#include <linux/of_mtd.h>
> >>  #include <linux/mtd/mtd.h>
> >>  #include <linux/mtd/nand.h>
> >>  #include <linux/mtd/partitions.h>
> >> @@ -130,6 +131,7 @@ static int __init orion_nand_probe(struct platform_device *pdev)
> >>  		if (!of_property_read_u32(pdev->dev.of_node,
> >>  						"chip-delay", &val))
> >>  			board->chip_delay = (u8)val;
> >> +		board->ecc_mode = of_get_nand_ecc_mode(pdev->dev.of_node);
> > 
> >>  	} else
> >>  		board = pdev->dev.platform_data;
> >>  
> >> @@ -140,7 +142,8 @@ static int __init orion_nand_probe(struct platform_device *pdev)
> >>  	nc->IO_ADDR_R = nc->IO_ADDR_W = io_base;
> >>  	nc->cmd_ctrl = orion_nand_cmd_ctrl;
> >>  	nc->read_buf = orion_nand_read_buf;
> >> -	nc->ecc.mode = NAND_ECC_SOFT;
> >> +	nc->ecc.mode = board->ecc_mode == NAND_ECC_SOFT_BCH ?
> >> +		NAND_ECC_SOFT_BCH : NAND_ECC_SOFT;
> > 
> > Hi Stefan
> > 
> > What about a user that wants one of the other valid values?
> > NAND_ECC_OOB_FIRST, NAND_ECC_HW_SYNDROME, etc.
> 
> As far as I understand, NAND_ECC_NONE, NAND_ECC_SOFT and
> NAND_ECC_SOFT_BCH are the only ECC modes that do not require
> corresponding hardware support which is missing in the marvell
> 88F6180/88F619x/88F628x. From my point of view, NAND_ECC_NONE does not
> make sense, too, because MLC NAND Flash requires ECC to be usable.
> 
> > 
> > Would:
> > 
> > 	if (IS_ERR(board->ecc_mode)) {
> > 		nc->ecc.mode = NAND_ECC_SOFT;
> > 		dev_info(&pdev->dev, "Defaulting to NAND_ECC_SOFT");
> > 	} else
> > 		nc->ecc.mode = board->ecc_mode
> > 
> > be better?
> 
> I feel safer by limiting the modes to what I could test.

Hi Stefan

O.K, but i still think a warning message would be useful when
board->ecc_mode is an error code.

		Andrew

Re: [PATCH 3/4] Enable ecc-mode selection in the driver

[Andrew Lunn]

On Wed, Jan 16, 2013 at 12:43:57PM +0100, Stefan Peter wrote:
> Hi Andrew
> 
> on 15.01.2013 13:51, Andrew Lunn wrote:
> > On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
> >> In order to be able to use the ecc-mode, add the bch module to the default
> >> settings for the kirwood boards and enable the activation in orin-nand.c
> >>
> >> Signed-off-by: Stefan Peter <s.peter@mpl.ch>
> >> ---
> >> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
> >> index 93f3794..4a9d3f7 100644
> >> --- a/arch/arm/configs/kirkwood_defconfig
> >> +++ b/arch/arm/configs/kirkwood_defconfig
> >> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
> >>  CONFIG_MTD_PHYSMAP=y
> >>  CONFIG_MTD_M25P80=y
> >>  CONFIG_MTD_NAND=y
> >> +CONFIG_MTD_NAND_ECC_BCH=y
> >>  CONFIG_MTD_NAND_ORION=y
> >>  CONFIG_BLK_DEV_LOOP=y
> >>  # CONFIG_SCSI_PROC_FS is not set
> >> diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c
> >> index cd72b92..1a35257 100644
> >> --- a/drivers/mtd/nand/orion_nand.c
> >> +++ b/drivers/mtd/nand/orion_nand.c
> >> @@ -14,6 +14,7 @@
> >>  #include <linux/module.h>
> >>  #include <linux/platform_device.h>
> >>  #include <linux/of.h>
> >> +#include <linux/of_mtd.h>
> >>  #include <linux/mtd/mtd.h>
> >>  #include <linux/mtd/nand.h>
> >>  #include <linux/mtd/partitions.h>
> >> @@ -130,6 +131,7 @@ static int __init orion_nand_probe(struct platform_device *pdev)
> >>  		if (!of_property_read_u32(pdev->dev.of_node,
> >>  						"chip-delay", &val))
> >>  			board->chip_delay = (u8)val;
> >> +		board->ecc_mode = of_get_nand_ecc_mode(pdev->dev.of_node);
> > 
> >>  	} else
> >>  		board = pdev->dev.platform_data;
> >>  
> >> @@ -140,7 +142,8 @@ static int __init orion_nand_probe(struct platform_device *pdev)
> >>  	nc->IO_ADDR_R = nc->IO_ADDR_W = io_base;
> >>  	nc->cmd_ctrl = orion_nand_cmd_ctrl;
> >>  	nc->read_buf = orion_nand_read_buf;
> >> -	nc->ecc.mode = NAND_ECC_SOFT;
> >> +	nc->ecc.mode = board->ecc_mode == NAND_ECC_SOFT_BCH ?
> >> +		NAND_ECC_SOFT_BCH : NAND_ECC_SOFT;
> > 
> > Hi Stefan
> > 
> > What about a user that wants one of the other valid values?
> > NAND_ECC_OOB_FIRST, NAND_ECC_HW_SYNDROME, etc.
> 
> As far as I understand, NAND_ECC_NONE, NAND_ECC_SOFT and
> NAND_ECC_SOFT_BCH are the only ECC modes that do not require
> corresponding hardware support which is missing in the marvell
> 88F6180/88F619x/88F628x. From my point of view, NAND_ECC_NONE does not
> make sense, too, because MLC NAND Flash requires ECC to be usable.
> 
> > 
> > Would:
> > 
> > 	if (IS_ERR(board->ecc_mode)) {
> > 		nc->ecc.mode = NAND_ECC_SOFT;
> > 		dev_info(&pdev->dev, "Defaulting to NAND_ECC_SOFT");
> > 	} else
> > 		nc->ecc.mode = board->ecc_mode
> > 
> > be better?
> 
> I feel safer by limiting the modes to what I could test.

Hi Stefan

O.K, but i still think a warning message would be useful when
board->ecc_mode is an error code.

		Andrew

[PATCH 3/4] Enable ecc-mode selection in the driver

[Andrew Lunn]

On Wed, Jan 16, 2013 at 12:43:57PM +0100, Stefan Peter wrote:
> Hi Andrew
> 
> on 15.01.2013 13:51, Andrew Lunn wrote:
> > On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
> >> In order to be able to use the ecc-mode, add the bch module to the default
> >> settings for the kirwood boards and enable the activation in orin-nand.c
> >>
> >> Signed-off-by: Stefan Peter <s.peter@mpl.ch>
> >> ---
> >> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
> >> index 93f3794..4a9d3f7 100644
> >> --- a/arch/arm/configs/kirkwood_defconfig
> >> +++ b/arch/arm/configs/kirkwood_defconfig
> >> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
> >>  CONFIG_MTD_PHYSMAP=y
> >>  CONFIG_MTD_M25P80=y
> >>  CONFIG_MTD_NAND=y
> >> +CONFIG_MTD_NAND_ECC_BCH=y
> >>  CONFIG_MTD_NAND_ORION=y
> >>  CONFIG_BLK_DEV_LOOP=y
> >>  # CONFIG_SCSI_PROC_FS is not set
> >> diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c
> >> index cd72b92..1a35257 100644
> >> --- a/drivers/mtd/nand/orion_nand.c
> >> +++ b/drivers/mtd/nand/orion_nand.c
> >> @@ -14,6 +14,7 @@
> >>  #include <linux/module.h>
> >>  #include <linux/platform_device.h>
> >>  #include <linux/of.h>
> >> +#include <linux/of_mtd.h>
> >>  #include <linux/mtd/mtd.h>
> >>  #include <linux/mtd/nand.h>
> >>  #include <linux/mtd/partitions.h>
> >> @@ -130,6 +131,7 @@ static int __init orion_nand_probe(struct platform_device *pdev)
> >>  		if (!of_property_read_u32(pdev->dev.of_node,
> >>  						"chip-delay", &val))
> >>  			board->chip_delay = (u8)val;
> >> +		board->ecc_mode = of_get_nand_ecc_mode(pdev->dev.of_node);
> > 
> >>  	} else
> >>  		board = pdev->dev.platform_data;
> >>  
> >> @@ -140,7 +142,8 @@ static int __init orion_nand_probe(struct platform_device *pdev)
> >>  	nc->IO_ADDR_R = nc->IO_ADDR_W = io_base;
> >>  	nc->cmd_ctrl = orion_nand_cmd_ctrl;
> >>  	nc->read_buf = orion_nand_read_buf;
> >> -	nc->ecc.mode = NAND_ECC_SOFT;
> >> +	nc->ecc.mode = board->ecc_mode == NAND_ECC_SOFT_BCH ?
> >> +		NAND_ECC_SOFT_BCH : NAND_ECC_SOFT;
> > 
> > Hi Stefan
> > 
> > What about a user that wants one of the other valid values?
> > NAND_ECC_OOB_FIRST, NAND_ECC_HW_SYNDROME, etc.
> 
> As far as I understand, NAND_ECC_NONE, NAND_ECC_SOFT and
> NAND_ECC_SOFT_BCH are the only ECC modes that do not require
> corresponding hardware support which is missing in the marvell
> 88F6180/88F619x/88F628x. From my point of view, NAND_ECC_NONE does not
> make sense, too, because MLC NAND Flash requires ECC to be usable.
> 
> > 
> > Would:
> > 
> > 	if (IS_ERR(board->ecc_mode)) {
> > 		nc->ecc.mode = NAND_ECC_SOFT;
> > 		dev_info(&pdev->dev, "Defaulting to NAND_ECC_SOFT");
> > 	} else
> > 		nc->ecc.mode = board->ecc_mode
> > 
> > be better?
> 
> I feel safer by limiting the modes to what I could test.

Hi Stefan

O.K, but i still think a warning message would be useful when
board->ecc_mode is an error code.

		Andrew

Re: [PATCH 3/4] Enable ecc-mode selection in the driver

[Artem Bityutskiy]

[-- Attachment #1: Type: text/plain, Size: 194 bytes --]

On Wed, 2013-01-16 at 12:43 +0100, Stefan Peter wrote:
> Hi Andrew

For some reasons I do not see your patches in the mailing lists which
are in CC.

-- 
Best Regards,
Artem Bityutskiy

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH 3/4] Enable ecc-mode selection in the driver

[Artem Bityutskiy]

[-- Attachment #1: Type: text/plain, Size: 194 bytes --]

On Wed, 2013-01-16 at 12:43 +0100, Stefan Peter wrote:
> Hi Andrew

For some reasons I do not see your patches in the mailing lists which
are in CC.

-- 
Best Regards,
Artem Bityutskiy

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

[PATCH 3/4] Enable ecc-mode selection in the driver

[Artem Bityutskiy]

On Wed, 2013-01-16 at 12:43 +0100, Stefan Peter wrote:
> Hi Andrew

For some reasons I do not see your patches in the mailing lists which
are in CC.

-- 
Best Regards,
Artem Bityutskiy
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20130118/ca0be53c/attachment.sig>