* [PATCH v3 0/2] Input: twl6040-vibra cleanups (devm_* conversion, system wq) @ 2013-01-14 15:34 ` Peter Ujfalusi 0 siblings, 0 replies; 9+ messages in thread From: Peter Ujfalusi @ 2013-01-14 15:34 UTC (permalink / raw) To: Dmitry Torokhov; +Cc: linux-input, linux-kernel Hi Dmitry, Changes since v2: - twl4030-vibra patches are left out (they have been applied) - Do not use devm_input_allocate_device() in twl6040-vibra Changes since v1: - Use devm_input_allocate_device() - swtich drivers to use system workqueue Cover letter from v1 (resend set): This series seams to got lost: https://lkml.org/lkml/2012/6/15/128 Can you take it for 3.9? Convert the twl4030, twl6040 vibra drivers to use devm_ at probe time to clean up the code a bit. The twl6040-vibra driver needed bigger change since the ordering of the initialization was not correct. Regards, Peter --- Peter Ujfalusi (2): Input: twl6040-vibra: Code cleanup in probe with devm_* conversion input: twl6040-vibra: Use system workqueue drivers/input/misc/twl6040-vibra.c | 100 +++++++++++++++---------------------- 1 file changed, 41 insertions(+), 59 deletions(-) -- 1.8.1 ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH v3 0/2] Input: twl6040-vibra cleanups (devm_* conversion, system wq) @ 2013-01-14 15:34 ` Peter Ujfalusi 0 siblings, 0 replies; 9+ messages in thread From: Peter Ujfalusi @ 2013-01-14 15:34 UTC (permalink / raw) To: Dmitry Torokhov; +Cc: linux-input, linux-kernel Hi Dmitry, Changes since v2: - twl4030-vibra patches are left out (they have been applied) - Do not use devm_input_allocate_device() in twl6040-vibra Changes since v1: - Use devm_input_allocate_device() - swtich drivers to use system workqueue Cover letter from v1 (resend set): This series seams to got lost: https://lkml.org/lkml/2012/6/15/128 Can you take it for 3.9? Convert the twl4030, twl6040 vibra drivers to use devm_ at probe time to clean up the code a bit. The twl6040-vibra driver needed bigger change since the ordering of the initialization was not correct. Regards, Peter --- Peter Ujfalusi (2): Input: twl6040-vibra: Code cleanup in probe with devm_* conversion input: twl6040-vibra: Use system workqueue drivers/input/misc/twl6040-vibra.c | 100 +++++++++++++++---------------------- 1 file changed, 41 insertions(+), 59 deletions(-) -- 1.8.1 ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH v3 1/2] Input: twl6040-vibra: Code cleanup in probe with devm_* conversion 2013-01-14 15:34 ` Peter Ujfalusi @ 2013-01-14 15:34 ` Peter Ujfalusi -1 siblings, 0 replies; 9+ messages in thread From: Peter Ujfalusi @ 2013-01-14 15:34 UTC (permalink / raw) To: Dmitry Torokhov; +Cc: linux-input, linux-kernel Convert the probe to use devm_*. At the same time reorder the calls so we will register the input device as the last step when the driver is loaded. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> --- drivers/input/misc/twl6040-vibra.c | 99 +++++++++++++++++--------------------- 1 file changed, 45 insertions(+), 54 deletions(-) diff --git a/drivers/input/misc/twl6040-vibra.c b/drivers/input/misc/twl6040-vibra.c index 71a28ee..d1e31b8 100644 --- a/drivers/input/misc/twl6040-vibra.c +++ b/drivers/input/misc/twl6040-vibra.c @@ -275,7 +275,7 @@ static int twl6040_vibra_probe(struct platform_device *pdev) return -EINVAL; } - info = kzalloc(sizeof(*info), GFP_KERNEL); + info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL); if (!info) { dev_err(&pdev->dev, "couldn't allocate memory\n"); return -ENOMEM; @@ -309,53 +309,23 @@ static int twl6040_vibra_probe(struct platform_device *pdev) if ((!info->vibldrv_res && !info->viblmotor_res) || (!info->vibrdrv_res && !info->vibrmotor_res)) { dev_err(info->dev, "invalid vibra driver/motor resistance\n"); - ret = -EINVAL; - goto err_kzalloc; + return -EINVAL; } info->irq = platform_get_irq(pdev, 0); if (info->irq < 0) { dev_err(info->dev, "invalid irq\n"); - ret = -EINVAL; - goto err_kzalloc; + return -EINVAL; } mutex_init(&info->mutex); - info->input_dev = input_allocate_device(); - if (info->input_dev == NULL) { - dev_err(info->dev, "couldn't allocate input device\n"); - ret = -ENOMEM; - goto err_kzalloc; - } - - input_set_drvdata(info->input_dev, info); - - info->input_dev->name = "twl6040:vibrator"; - info->input_dev->id.version = 1; - info->input_dev->dev.parent = pdev->dev.parent; - info->input_dev->close = twl6040_vibra_close; - __set_bit(FF_RUMBLE, info->input_dev->ffbit); - - ret = input_ff_create_memless(info->input_dev, NULL, vibra_play); - if (ret < 0) { - dev_err(info->dev, "couldn't register vibrator to FF\n"); - goto err_ialloc; - } - - ret = input_register_device(info->input_dev); - if (ret < 0) { - dev_err(info->dev, "couldn't register input device\n"); - goto err_iff; - } - - platform_set_drvdata(pdev, info); - - ret = request_threaded_irq(info->irq, NULL, twl6040_vib_irq_handler, 0, - "twl6040_irq_vib", info); + ret = devm_request_threaded_irq(&pdev->dev, info->irq, NULL, + twl6040_vib_irq_handler, 0, + "twl6040_irq_vib", info); if (ret) { dev_err(info->dev, "VIB IRQ request failed: %d\n", ret); - goto err_irq; + return ret; } info->supplies[0].supply = "vddvibl"; @@ -368,7 +338,7 @@ static int twl6040_vibra_probe(struct platform_device *pdev) ARRAY_SIZE(info->supplies), info->supplies); if (ret) { dev_err(info->dev, "couldn't get regulators %d\n", ret); - goto err_regulator; + return ret; } if (vddvibl_uV) { @@ -377,7 +347,7 @@ static int twl6040_vibra_probe(struct platform_device *pdev) if (ret) { dev_err(info->dev, "failed to set VDDVIBL volt %d\n", ret); - goto err_voltage; + goto err_regulator; } } @@ -387,7 +357,7 @@ static int twl6040_vibra_probe(struct platform_device *pdev) if (ret) { dev_err(info->dev, "failed to set VDDVIBR volt %d\n", ret); - goto err_voltage; + goto err_regulator; } } @@ -395,26 +365,49 @@ static int twl6040_vibra_probe(struct platform_device *pdev) if (info->workqueue == NULL) { dev_err(info->dev, "couldn't create workqueue\n"); ret = -ENOMEM; - goto err_voltage; + goto err_regulator; } INIT_WORK(&info->play_work, vibra_play_work); + info->input_dev = input_allocate_device(); + if (info->input_dev == NULL) { + dev_err(info->dev, "couldn't allocate input device\n"); + ret = -ENOMEM; + goto err_wq; + } + + input_set_drvdata(info->input_dev, info); + + info->input_dev->name = "twl6040:vibrator"; + info->input_dev->id.version = 1; + info->input_dev->dev.parent = pdev->dev.parent; + info->input_dev->close = twl6040_vibra_close; + __set_bit(FF_RUMBLE, info->input_dev->ffbit); + + ret = input_ff_create_memless(info->input_dev, NULL, vibra_play); + if (ret < 0) { + dev_err(info->dev, "couldn't register vibrator to FF\n"); + goto err_ialloc; + } + + ret = input_register_device(info->input_dev); + if (ret < 0) { + dev_err(info->dev, "couldn't register input device\n"); + goto err_iff; + } + + platform_set_drvdata(pdev, info); + return 0; -err_voltage: - regulator_bulk_free(ARRAY_SIZE(info->supplies), info->supplies); -err_regulator: - free_irq(info->irq, info); -err_irq: - input_unregister_device(info->input_dev); - info->input_dev = NULL; err_iff: - if (info->input_dev) - input_ff_destroy(info->input_dev); + input_ff_destroy(info->input_dev); err_ialloc: input_free_device(info->input_dev); -err_kzalloc: - kfree(info); +err_wq: + destroy_workqueue(info->workqueue); +err_regulator: + regulator_bulk_free(ARRAY_SIZE(info->supplies), info->supplies); return ret; } @@ -423,10 +416,8 @@ static int twl6040_vibra_remove(struct platform_device *pdev) struct vibra_info *info = platform_get_drvdata(pdev); input_unregister_device(info->input_dev); - free_irq(info->irq, info); regulator_bulk_free(ARRAY_SIZE(info->supplies), info->supplies); destroy_workqueue(info->workqueue); - kfree(info); return 0; } -- 1.8.1 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v3 1/2] Input: twl6040-vibra: Code cleanup in probe with devm_* conversion @ 2013-01-14 15:34 ` Peter Ujfalusi 0 siblings, 0 replies; 9+ messages in thread From: Peter Ujfalusi @ 2013-01-14 15:34 UTC (permalink / raw) To: Dmitry Torokhov; +Cc: linux-input, linux-kernel Convert the probe to use devm_*. At the same time reorder the calls so we will register the input device as the last step when the driver is loaded. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> --- drivers/input/misc/twl6040-vibra.c | 99 +++++++++++++++++--------------------- 1 file changed, 45 insertions(+), 54 deletions(-) diff --git a/drivers/input/misc/twl6040-vibra.c b/drivers/input/misc/twl6040-vibra.c index 71a28ee..d1e31b8 100644 --- a/drivers/input/misc/twl6040-vibra.c +++ b/drivers/input/misc/twl6040-vibra.c @@ -275,7 +275,7 @@ static int twl6040_vibra_probe(struct platform_device *pdev) return -EINVAL; } - info = kzalloc(sizeof(*info), GFP_KERNEL); + info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL); if (!info) { dev_err(&pdev->dev, "couldn't allocate memory\n"); return -ENOMEM; @@ -309,53 +309,23 @@ static int twl6040_vibra_probe(struct platform_device *pdev) if ((!info->vibldrv_res && !info->viblmotor_res) || (!info->vibrdrv_res && !info->vibrmotor_res)) { dev_err(info->dev, "invalid vibra driver/motor resistance\n"); - ret = -EINVAL; - goto err_kzalloc; + return -EINVAL; } info->irq = platform_get_irq(pdev, 0); if (info->irq < 0) { dev_err(info->dev, "invalid irq\n"); - ret = -EINVAL; - goto err_kzalloc; + return -EINVAL; } mutex_init(&info->mutex); - info->input_dev = input_allocate_device(); - if (info->input_dev == NULL) { - dev_err(info->dev, "couldn't allocate input device\n"); - ret = -ENOMEM; - goto err_kzalloc; - } - - input_set_drvdata(info->input_dev, info); - - info->input_dev->name = "twl6040:vibrator"; - info->input_dev->id.version = 1; - info->input_dev->dev.parent = pdev->dev.parent; - info->input_dev->close = twl6040_vibra_close; - __set_bit(FF_RUMBLE, info->input_dev->ffbit); - - ret = input_ff_create_memless(info->input_dev, NULL, vibra_play); - if (ret < 0) { - dev_err(info->dev, "couldn't register vibrator to FF\n"); - goto err_ialloc; - } - - ret = input_register_device(info->input_dev); - if (ret < 0) { - dev_err(info->dev, "couldn't register input device\n"); - goto err_iff; - } - - platform_set_drvdata(pdev, info); - - ret = request_threaded_irq(info->irq, NULL, twl6040_vib_irq_handler, 0, - "twl6040_irq_vib", info); + ret = devm_request_threaded_irq(&pdev->dev, info->irq, NULL, + twl6040_vib_irq_handler, 0, + "twl6040_irq_vib", info); if (ret) { dev_err(info->dev, "VIB IRQ request failed: %d\n", ret); - goto err_irq; + return ret; } info->supplies[0].supply = "vddvibl"; @@ -368,7 +338,7 @@ static int twl6040_vibra_probe(struct platform_device *pdev) ARRAY_SIZE(info->supplies), info->supplies); if (ret) { dev_err(info->dev, "couldn't get regulators %d\n", ret); - goto err_regulator; + return ret; } if (vddvibl_uV) { @@ -377,7 +347,7 @@ static int twl6040_vibra_probe(struct platform_device *pdev) if (ret) { dev_err(info->dev, "failed to set VDDVIBL volt %d\n", ret); - goto err_voltage; + goto err_regulator; } } @@ -387,7 +357,7 @@ static int twl6040_vibra_probe(struct platform_device *pdev) if (ret) { dev_err(info->dev, "failed to set VDDVIBR volt %d\n", ret); - goto err_voltage; + goto err_regulator; } } @@ -395,26 +365,49 @@ static int twl6040_vibra_probe(struct platform_device *pdev) if (info->workqueue == NULL) { dev_err(info->dev, "couldn't create workqueue\n"); ret = -ENOMEM; - goto err_voltage; + goto err_regulator; } INIT_WORK(&info->play_work, vibra_play_work); + info->input_dev = input_allocate_device(); + if (info->input_dev == NULL) { + dev_err(info->dev, "couldn't allocate input device\n"); + ret = -ENOMEM; + goto err_wq; + } + + input_set_drvdata(info->input_dev, info); + + info->input_dev->name = "twl6040:vibrator"; + info->input_dev->id.version = 1; + info->input_dev->dev.parent = pdev->dev.parent; + info->input_dev->close = twl6040_vibra_close; + __set_bit(FF_RUMBLE, info->input_dev->ffbit); + + ret = input_ff_create_memless(info->input_dev, NULL, vibra_play); + if (ret < 0) { + dev_err(info->dev, "couldn't register vibrator to FF\n"); + goto err_ialloc; + } + + ret = input_register_device(info->input_dev); + if (ret < 0) { + dev_err(info->dev, "couldn't register input device\n"); + goto err_iff; + } + + platform_set_drvdata(pdev, info); + return 0; -err_voltage: - regulator_bulk_free(ARRAY_SIZE(info->supplies), info->supplies); -err_regulator: - free_irq(info->irq, info); -err_irq: - input_unregister_device(info->input_dev); - info->input_dev = NULL; err_iff: - if (info->input_dev) - input_ff_destroy(info->input_dev); + input_ff_destroy(info->input_dev); err_ialloc: input_free_device(info->input_dev); -err_kzalloc: - kfree(info); +err_wq: + destroy_workqueue(info->workqueue); +err_regulator: + regulator_bulk_free(ARRAY_SIZE(info->supplies), info->supplies); return ret; } @@ -423,10 +416,8 @@ static int twl6040_vibra_remove(struct platform_device *pdev) struct vibra_info *info = platform_get_drvdata(pdev); input_unregister_device(info->input_dev); - free_irq(info->irq, info); regulator_bulk_free(ARRAY_SIZE(info->supplies), info->supplies); destroy_workqueue(info->workqueue); - kfree(info); return 0; } -- 1.8.1 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v3 2/2] input: twl6040-vibra: Use system workqueue 2013-01-14 15:34 ` Peter Ujfalusi @ 2013-01-14 15:34 ` Peter Ujfalusi -1 siblings, 0 replies; 9+ messages in thread From: Peter Ujfalusi @ 2013-01-14 15:34 UTC (permalink / raw) To: Dmitry Torokhov; +Cc: linux-input, linux-kernel It is time to switch to system wq instead creating a queue for the driver. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> --- drivers/input/misc/twl6040-vibra.c | 11 +---------- 1 file changed, 1 insertion(+), 10 deletions(-) diff --git a/drivers/input/misc/twl6040-vibra.c b/drivers/input/misc/twl6040-vibra.c index d1e31b8..0c2dfc8 100644 --- a/drivers/input/misc/twl6040-vibra.c +++ b/drivers/input/misc/twl6040-vibra.c @@ -361,19 +361,13 @@ static int twl6040_vibra_probe(struct platform_device *pdev) } } - info->workqueue = alloc_workqueue("twl6040-vibra", 0, 0); - if (info->workqueue == NULL) { - dev_err(info->dev, "couldn't create workqueue\n"); - ret = -ENOMEM; - goto err_regulator; - } INIT_WORK(&info->play_work, vibra_play_work); info->input_dev = input_allocate_device(); if (info->input_dev == NULL) { dev_err(info->dev, "couldn't allocate input device\n"); ret = -ENOMEM; - goto err_wq; + goto err_regulator; } input_set_drvdata(info->input_dev, info); @@ -404,8 +398,6 @@ err_iff: input_ff_destroy(info->input_dev); err_ialloc: input_free_device(info->input_dev); -err_wq: - destroy_workqueue(info->workqueue); err_regulator: regulator_bulk_free(ARRAY_SIZE(info->supplies), info->supplies); return ret; @@ -417,7 +409,6 @@ static int twl6040_vibra_remove(struct platform_device *pdev) input_unregister_device(info->input_dev); regulator_bulk_free(ARRAY_SIZE(info->supplies), info->supplies); - destroy_workqueue(info->workqueue); return 0; } -- 1.8.1 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v3 2/2] input: twl6040-vibra: Use system workqueue @ 2013-01-14 15:34 ` Peter Ujfalusi 0 siblings, 0 replies; 9+ messages in thread From: Peter Ujfalusi @ 2013-01-14 15:34 UTC (permalink / raw) To: Dmitry Torokhov; +Cc: linux-input, linux-kernel It is time to switch to system wq instead creating a queue for the driver. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> --- drivers/input/misc/twl6040-vibra.c | 11 +---------- 1 file changed, 1 insertion(+), 10 deletions(-) diff --git a/drivers/input/misc/twl6040-vibra.c b/drivers/input/misc/twl6040-vibra.c index d1e31b8..0c2dfc8 100644 --- a/drivers/input/misc/twl6040-vibra.c +++ b/drivers/input/misc/twl6040-vibra.c @@ -361,19 +361,13 @@ static int twl6040_vibra_probe(struct platform_device *pdev) } } - info->workqueue = alloc_workqueue("twl6040-vibra", 0, 0); - if (info->workqueue == NULL) { - dev_err(info->dev, "couldn't create workqueue\n"); - ret = -ENOMEM; - goto err_regulator; - } INIT_WORK(&info->play_work, vibra_play_work); info->input_dev = input_allocate_device(); if (info->input_dev == NULL) { dev_err(info->dev, "couldn't allocate input device\n"); ret = -ENOMEM; - goto err_wq; + goto err_regulator; } input_set_drvdata(info->input_dev, info); @@ -404,8 +398,6 @@ err_iff: input_ff_destroy(info->input_dev); err_ialloc: input_free_device(info->input_dev); -err_wq: - destroy_workqueue(info->workqueue); err_regulator: regulator_bulk_free(ARRAY_SIZE(info->supplies), info->supplies); return ret; @@ -417,7 +409,6 @@ static int twl6040_vibra_remove(struct platform_device *pdev) input_unregister_device(info->input_dev); regulator_bulk_free(ARRAY_SIZE(info->supplies), info->supplies); - destroy_workqueue(info->workqueue); return 0; } -- 1.8.1 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: [PATCH v3 0/2] Input: twl6040-vibra cleanups (devm_* conversion, system wq) 2013-01-14 15:34 ` Peter Ujfalusi @ 2013-01-24 11:44 ` Peter Ujfalusi -1 siblings, 0 replies; 9+ messages in thread From: Peter Ujfalusi @ 2013-01-24 11:44 UTC (permalink / raw) To: Dmitry Torokhov; +Cc: linux-input, linux-kernel Hi Dmitry, On 01/14/2013 04:34 PM, Peter Ujfalusi wrote: > Hi Dmitry, > > Changes since v2: > - twl4030-vibra patches are left out (they have been applied) > - Do not use devm_input_allocate_device() in twl6040-vibra Do you want me to resend this two patch for 3.9? Regards, Péter > > Changes since v1: > - Use devm_input_allocate_device() > - swtich drivers to use system workqueue > > Cover letter from v1 (resend set): > > This series seams to got lost: > https://lkml.org/lkml/2012/6/15/128 > > Can you take it for 3.9? > > Convert the twl4030, twl6040 vibra drivers to use devm_ at probe time to clean > up the code a bit. > The twl6040-vibra driver needed bigger change since the ordering of the > initialization was not correct. > > Regards, > Peter > --- > Peter Ujfalusi (2): > Input: twl6040-vibra: Code cleanup in probe with devm_* conversion > input: twl6040-vibra: Use system workqueue > > drivers/input/misc/twl6040-vibra.c | 100 +++++++++++++++---------------------- > 1 file changed, 41 insertions(+), 59 deletions(-) > -- To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH v3 0/2] Input: twl6040-vibra cleanups (devm_* conversion, system wq) @ 2013-01-24 11:44 ` Peter Ujfalusi 0 siblings, 0 replies; 9+ messages in thread From: Peter Ujfalusi @ 2013-01-24 11:44 UTC (permalink / raw) To: Dmitry Torokhov; +Cc: linux-input, linux-kernel Hi Dmitry, On 01/14/2013 04:34 PM, Peter Ujfalusi wrote: > Hi Dmitry, > > Changes since v2: > - twl4030-vibra patches are left out (they have been applied) > - Do not use devm_input_allocate_device() in twl6040-vibra Do you want me to resend this two patch for 3.9? Regards, Péter > > Changes since v1: > - Use devm_input_allocate_device() > - swtich drivers to use system workqueue > > Cover letter from v1 (resend set): > > This series seams to got lost: > https://lkml.org/lkml/2012/6/15/128 > > Can you take it for 3.9? > > Convert the twl4030, twl6040 vibra drivers to use devm_ at probe time to clean > up the code a bit. > The twl6040-vibra driver needed bigger change since the ordering of the > initialization was not correct. > > Regards, > Peter > --- > Peter Ujfalusi (2): > Input: twl6040-vibra: Code cleanup in probe with devm_* conversion > input: twl6040-vibra: Use system workqueue > > drivers/input/misc/twl6040-vibra.c | 100 +++++++++++++++---------------------- > 1 file changed, 41 insertions(+), 59 deletions(-) > ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH v3 0/2] Input: twl6040-vibra cleanups (devm_* conversion, system wq) 2013-01-24 11:44 ` Peter Ujfalusi (?) @ 2013-01-25 8:20 ` Dmitry Torokhov -1 siblings, 0 replies; 9+ messages in thread From: Dmitry Torokhov @ 2013-01-25 8:20 UTC (permalink / raw) To: Peter Ujfalusi; +Cc: linux-input, linux-kernel Hi Peter, On Thu, Jan 24, 2013 at 12:44:29PM +0100, Peter Ujfalusi wrote: > Hi Dmitry, > > On 01/14/2013 04:34 PM, Peter Ujfalusi wrote: > > Hi Dmitry, > > > > Changes since v2: > > - twl4030-vibra patches are left out (they have been applied) > > - Do not use devm_input_allocate_device() in twl6040-vibra > > Do you want me to resend this two patch for 3.9? No, I queued them for 3.9. Thanks. -- Dmitry ^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2013-01-25 8:20 UTC | newest] Thread overview: 9+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2013-01-14 15:34 [PATCH v3 0/2] Input: twl6040-vibra cleanups (devm_* conversion, system wq) Peter Ujfalusi 2013-01-14 15:34 ` Peter Ujfalusi 2013-01-14 15:34 ` [PATCH v3 1/2] Input: twl6040-vibra: Code cleanup in probe with devm_* conversion Peter Ujfalusi 2013-01-14 15:34 ` Peter Ujfalusi 2013-01-14 15:34 ` [PATCH v3 2/2] input: twl6040-vibra: Use system workqueue Peter Ujfalusi 2013-01-14 15:34 ` Peter Ujfalusi 2013-01-24 11:44 ` [PATCH v3 0/2] Input: twl6040-vibra cleanups (devm_* conversion, system wq) Peter Ujfalusi 2013-01-24 11:44 ` Peter Ujfalusi 2013-01-25 8:20 ` Dmitry Torokhov
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.