* Fwd: Intel Wifilink 5100 AGN - Does it support Access Point Infrastructure Mode ? [not found] ` <CABFmVg5AaTG-F_myEA=WGdYpnwN9X=QfLcjKvwJ1-SUX0quaOg@mail.gmail.com> @ 2013-03-02 9:51 ` Abdelmuhaimen Seaudi 2013-03-02 10:22 ` Pat Erley 2013-03-02 10:27 ` Pat Erley 0 siblings, 2 replies; 6+ messages in thread From: Abdelmuhaimen Seaudi @ 2013-03-02 9:51 UTC (permalink / raw) To: linux-wireless Hello iwlwifi support, I want to run my Wifi Intel WifiLink 5100 AGN in Access Point Infrstructure Mode, so that I can connect via WiFi with other devices to my workstation. This is under Ubuntu Linux 12.10. I have tried setting the wlan0 to run in master mode, but it gives me error, as shown below. Is it possible to run this WiFi radio in AP Infrstrucutre mode ? How ? Thanks, aseaudi@Home:~$ iwconfig wlan0 IEEE 802.11abgn ESSID:"3Com" Mode:Managed Frequency:2.462 GHz Access Point: 00:22:57:1F:C4:2B Bit Rate=48 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=51/70 Signal level=-59 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:468 Missed beacon:0 lo no wireless extensions. eth0 no wireless extensions. aseaudi@Home:~$ sudo iwconfig wlan0 mode master Error for wireless request "Set Mode" (8B06) : SET failed on device wlan0 ; Invalid argument. aseaudi@Home:~$ iw list Wiphy phy0 Band 1: Capabilities: 0x872 HT20/HT40 Static SM Power Save RX Greenfield RX HT20 SGI RX HT40 SGI No RX STBC Max AMSDU length: 7935 bytes No DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 4 usec (0x05) HT RX MCS rate indexes supported: 0-15, 32 TX unequal modulation not supported HT TX Max spatial streams: 1 HT TX MCS rate indexes supported may differ Frequencies: * 2412 MHz [1] (15.0 dBm) * 2417 MHz [2] (15.0 dBm) * 2422 MHz [3] (15.0 dBm) * 2427 MHz [4] (15.0 dBm) * 2432 MHz [5] (15.0 dBm) * 2437 MHz [6] (15.0 dBm) * 2442 MHz [7] (15.0 dBm) * 2447 MHz [8] (15.0 dBm) * 2452 MHz [9] (15.0 dBm) * 2457 MHz [10] (15.0 dBm) * 2462 MHz [11] (15.0 dBm) * 2467 MHz [12] (15.0 dBm) (passive scanning, no IBSS) * 2472 MHz [13] (15.0 dBm) (passive scanning, no IBSS) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Band 2: Capabilities: 0x872 HT20/HT40 Static SM Power Save RX Greenfield RX HT20 SGI RX HT40 SGI No RX STBC Max AMSDU length: 7935 bytes No DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 4 usec (0x05) HT RX MCS rate indexes supported: 0-15, 32 TX unequal modulation not supported HT TX Max spatial streams: 1 HT TX MCS rate indexes supported may differ Frequencies: * 5180 MHz [36] (13.0 dBm) (passive scanning, no IBSS) * 5200 MHz [40] (15.0 dBm) (passive scanning, no IBSS) * 5220 MHz [44] (15.0 dBm) (passive scanning, no IBSS) * 5240 MHz [48] (15.0 dBm) (passive scanning, no IBSS) * 5260 MHz [52] (15.0 dBm) (passive scanning, no IBSS, radar detection) * 5280 MHz [56] (15.0 dBm) (passive scanning, no IBSS, radar detection) * 5300 MHz [60] (15.0 dBm) (passive scanning, no IBSS, radar detection) * 5320 MHz [64] (13.0 dBm) (passive scanning, no IBSS, radar detection) * 5500 MHz [100] (15.0 dBm) (passive scanning, no IBSS, radar detection) * 5520 MHz [104] (15.0 dBm) (passive scanning, no IBSS, radar detection) * 5540 MHz [108] (15.0 dBm) (passive scanning, no IBSS, radar detection) * 5560 MHz [112] (15.0 dBm) (passive scanning, no IBSS, radar detection) * 5580 MHz [116] (15.0 dBm) (passive scanning, no IBSS, radar detection) * 5600 MHz [120] (15.0 dBm) (passive scanning, no IBSS, radar detection) * 5620 MHz [124] (15.0 dBm) (passive scanning, no IBSS, radar detection) * 5640 MHz [128] (15.0 dBm) (passive scanning, no IBSS, radar detection) * 5660 MHz [132] (15.0 dBm) (passive scanning, no IBSS, radar detection) * 5680 MHz [136] (15.0 dBm) (passive scanning, no IBSS, radar detection) * 5700 MHz [140] (15.0 dBm) (passive scanning, no IBSS, radar detection) * 5745 MHz [149] (15.0 dBm) (passive scanning, no IBSS) * 5765 MHz [153] (15.0 dBm) (passive scanning, no IBSS) * 5785 MHz [157] (15.0 dBm) (passive scanning, no IBSS) * 5805 MHz [161] (15.0 dBm) (passive scanning, no IBSS) * 5825 MHz [165] (15.0 dBm) (passive scanning, no IBSS) Bitrates (non-HT): * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 20 max scan IEs length: 195 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS * managed * monitor software interface modes (can always be added): * monitor interface combinations are not supported Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * Unknown command (84) * Unknown command (87) * Unknown command (85) * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 Supported RX frame types: * IBSS: 0xd0 * managed: 0x40 0xd0 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * mesh point: 0xb0 0xc0 0xd0 * P2P-client: 0x40 0xd0 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 Device supports RSN-IBSS. HT Capability overrides: * MCS: ff ff ff ff ff ff ff ff ff ff * maximum A-MSDU length * supported channel width * short GI for 40 MHz * max A-MPDU length exponent * min MPDU start spacing Device supports TX status socket option. Device supports HT-IBSS. aseaudi@Home:~$ -- Thanks and best regards Abdel-Muhaimen Seaudi CCIE # 25265 aseaudi@gmail.com Tel.: +2010-0538-7426 -- Thanks and best regards Abdel-Muhaimen Seaudi CCIE # 25265 aseaudi@gmail.com Tel.: +2010-0538-7426 -- Thanks and best regards Abdel-Muhaimen Seaudi CCIE # 25265 aseaudi@gmail.com Tel.: +2010-0538-7426 ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Fwd: Intel Wifilink 5100 AGN - Does it support Access Point Infrastructure Mode ? 2013-03-02 9:51 ` Fwd: Intel Wifilink 5100 AGN - Does it support Access Point Infrastructure Mode ? Abdelmuhaimen Seaudi @ 2013-03-02 10:22 ` Pat Erley 2013-03-02 12:52 ` Abdelmuhaimen Seaudi 2013-03-02 10:27 ` Pat Erley 1 sibling, 1 reply; 6+ messages in thread From: Pat Erley @ 2013-03-02 10:22 UTC (permalink / raw) To: Abdelmuhaimen Seaudi; +Cc: linux-wireless On 03/02/2013 04:51 AM, Abdelmuhaimen Seaudi wrote: > Hello iwlwifi support, > I want to run my Wifi Intel WifiLink 5100 AGN in Access Point > Infrstructure Mode, so that I can connect via WiFi with other devices > to my workstation. > This is under Ubuntu Linux 12.10. > I have tried setting the wlan0 to run in master mode, but it gives me > error, as shown below. > Is it possible to run this WiFi radio in AP Infrstrucutre mode ? How ? > Thanks, > > aseaudi@Home:~$ iwconfig > wlan0 IEEE 802.11abgn ESSID:"3Com" > Mode:Managed Frequency:2.462 GHz Access Point: 00:22:57:1F:C4:2B > Bit Rate=48 Mb/s Tx-Power=15 dBm > Retry long limit:7 RTS thr:off Fragment thr:off > Power Management:off > Link Quality=51/70 Signal level=-59 dBm > Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 > Tx excessive retries:0 Invalid misc:468 Missed beacon:0 > lo no wireless extensions. > eth0 no wireless extensions. > > aseaudi@Home:~$ sudo iwconfig wlan0 mode master > Error for wireless request "Set Mode" (8B06) : > SET failed on device wlan0 ; Invalid argument. http://linuxwireless.org/en/users/Documentation/hostapd Master mode requires userspace to handle setup and control. That page should cover most/all of what you need. Pat Erley ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Fwd: Intel Wifilink 5100 AGN - Does it support Access Point Infrastructure Mode ? 2013-03-02 10:22 ` Pat Erley @ 2013-03-02 12:52 ` Abdelmuhaimen Seaudi 0 siblings, 0 replies; 6+ messages in thread From: Abdelmuhaimen Seaudi @ 2013-03-02 12:52 UTC (permalink / raw) To: Pat Erley; +Cc: linux-wireless Hello Pat, I have tried this, and I get the following error. Is there another way to enable AP master mode for the Intel WifiLink 5100 AGN ? Is there a driver or firmware that I can use to enable AP mode ? Thanks, aseaudi@Home:~$ sudo hostapd hostapd.conf Configuration file: hostapd.conf Failed to update rate sets in kernel module Could not connect to kernel driver. Using interface wlan0 with hwaddr 00:24:d6:5b:71:d2 and ssid 'test' Failed to set beacon parameters wlan0: STA 00:22:57:1f:c4:2b IEEE 802.11: disassociated ^CCould not connect to kernel driver. aseaudi@Home:~$ cat hostapd.conf #change wlan0 to your wireless device interface=wlan0 driver=nl80211 ssid=test channel=1 On 3/2/13, Pat Erley <pat-lkml@erley.org> wrote: > On 03/02/2013 04:51 AM, Abdelmuhaimen Seaudi wrote: >> Hello iwlwifi support, >> I want to run my Wifi Intel WifiLink 5100 AGN in Access Point >> Infrstructure Mode, so that I can connect via WiFi with other devices >> to my workstation. >> This is under Ubuntu Linux 12.10. >> I have tried setting the wlan0 to run in master mode, but it gives me >> error, as shown below. >> Is it possible to run this WiFi radio in AP Infrstrucutre mode ? How ? >> Thanks, >> >> aseaudi@Home:~$ iwconfig >> wlan0 IEEE 802.11abgn ESSID:"3Com" >> Mode:Managed Frequency:2.462 GHz Access Point: >> 00:22:57:1F:C4:2B >> Bit Rate=48 Mb/s Tx-Power=15 dBm >> Retry long limit:7 RTS thr:off Fragment thr:off >> Power Management:off >> Link Quality=51/70 Signal level=-59 dBm >> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 >> Tx excessive retries:0 Invalid misc:468 Missed beacon:0 >> lo no wireless extensions. >> eth0 no wireless extensions. >> >> aseaudi@Home:~$ sudo iwconfig wlan0 mode master >> Error for wireless request "Set Mode" (8B06) : >> SET failed on device wlan0 ; Invalid argument. > > http://linuxwireless.org/en/users/Documentation/hostapd > > Master mode requires userspace to handle setup and control. That page > should cover most/all of what you need. > > Pat Erley > > -- Thanks and best regards Abdel-Muhaimen Seaudi CCIE # 25265 aseaudi@gmail.com Tel.: +2010-0538-7426 ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Fwd: Intel Wifilink 5100 AGN - Does it support Access Point Infrastructure Mode ? 2013-03-02 9:51 ` Fwd: Intel Wifilink 5100 AGN - Does it support Access Point Infrastructure Mode ? Abdelmuhaimen Seaudi 2013-03-02 10:22 ` Pat Erley @ 2013-03-02 10:27 ` Pat Erley 2013-03-02 12:47 ` Abdelmuhaimen Seaudi 1 sibling, 1 reply; 6+ messages in thread From: Pat Erley @ 2013-03-02 10:27 UTC (permalink / raw) To: Abdelmuhaimen Seaudi; +Cc: linux-wireless On 03/02/2013 04:51 AM, Abdelmuhaimen Seaudi wrote: > Hello iwlwifi support, > I want to run my Wifi Intel WifiLink 5100 AGN in Access Point > Infrstructure Mode, so that I can connect via WiFi with other devices > to my workstation. > This is under Ubuntu Linux 12.10. > I have tried setting the wlan0 to run in master mode, but it gives me > error, as shown below. > Is it possible to run this WiFi radio in AP Infrstrucutre mode ? How ? > Thanks, > <SNIP> > Supported interface modes: > * IBSS > * managed > * monitor > software interface modes (can always be added): > * monitor It also looks like this chipset doesn't support master mode. Pat Erley ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Fwd: Intel Wifilink 5100 AGN - Does it support Access Point Infrastructure Mode ? 2013-03-02 10:27 ` Pat Erley @ 2013-03-02 12:47 ` Abdelmuhaimen Seaudi 2013-03-03 16:08 ` Dan Williams 0 siblings, 1 reply; 6+ messages in thread From: Abdelmuhaimen Seaudi @ 2013-03-02 12:47 UTC (permalink / raw) To: Pat Erley; +Cc: linux-wireless Hello Pat, So this means no way the Intel WiFiLink 5100 AGN will run in AP master mode, correct ? Note that it can run in Windows using program like Virtual Router, and I confirmed I was able to connect to my workstation wifi. Note also that it is not using Adhoc mode, it was using AP Infrastructure mode. Thanks for your confirmation. On 3/2/13, Pat Erley <pat-lkml@erley.org> wrote: > On 03/02/2013 04:51 AM, Abdelmuhaimen Seaudi wrote: >> Hello iwlwifi support, >> I want to run my Wifi Intel WifiLink 5100 AGN in Access Point >> Infrstructure Mode, so that I can connect via WiFi with other devices >> to my workstation. >> This is under Ubuntu Linux 12.10. >> I have tried setting the wlan0 to run in master mode, but it gives me >> error, as shown below. >> Is it possible to run this WiFi radio in AP Infrstrucutre mode ? How ? >> Thanks, >> > > <SNIP> > >> Supported interface modes: >> * IBSS >> * managed >> * monitor >> software interface modes (can always be added): >> * monitor > > It also looks like this chipset doesn't support master mode. > > Pat Erley > -- Thanks and best regards Abdel-Muhaimen Seaudi CCIE # 25265 aseaudi@gmail.com Tel.: +2010-0538-7426 ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Fwd: Intel Wifilink 5100 AGN - Does it support Access Point Infrastructure Mode ? 2013-03-02 12:47 ` Abdelmuhaimen Seaudi @ 2013-03-03 16:08 ` Dan Williams 0 siblings, 0 replies; 6+ messages in thread From: Dan Williams @ 2013-03-03 16:08 UTC (permalink / raw) To: Abdelmuhaimen Seaudi; +Cc: Pat Erley, linux-wireless On Sat, 2013-03-02 at 14:47 +0200, Abdelmuhaimen Seaudi wrote: > Hello Pat, > So this means no way the Intel WiFiLink 5100 AGN will run in AP master > mode, correct ? Correct. If the 'iw' command does not report "AP" mode, then that mode is not supported by the firmware and kernel version that you are running. AFAIK, the 51xx does not now and will not support AP mode on Linux in the future. Dan > Note that it can run in Windows using program like Virtual Router, and > I confirmed I was able to connect to my workstation wifi. Note also > that it is not using Adhoc mode, it was using AP Infrastructure mode. > Thanks for your confirmation. > > On 3/2/13, Pat Erley <pat-lkml@erley.org> wrote: > > On 03/02/2013 04:51 AM, Abdelmuhaimen Seaudi wrote: > >> Hello iwlwifi support, > >> I want to run my Wifi Intel WifiLink 5100 AGN in Access Point > >> Infrstructure Mode, so that I can connect via WiFi with other devices > >> to my workstation. > >> This is under Ubuntu Linux 12.10. > >> I have tried setting the wlan0 to run in master mode, but it gives me > >> error, as shown below. > >> Is it possible to run this WiFi radio in AP Infrstrucutre mode ? How ? > >> Thanks, > >> > > > > <SNIP> > > > >> Supported interface modes: > >> * IBSS > >> * managed > >> * monitor > >> software interface modes (can always be added): > >> * monitor > > > > It also looks like this chipset doesn't support master mode. > > > > Pat Erley > > > > ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2013-03-03 16:08 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <CABFmVg5sPub5Q4n+7PnkUn7weQLEUabONeJQZY6aFS2yFZAf2Q@mail.gmail.com>
[not found] ` <CABFmVg5AaTG-F_myEA=WGdYpnwN9X=QfLcjKvwJ1-SUX0quaOg@mail.gmail.com>
2013-03-02 9:51 ` Fwd: Intel Wifilink 5100 AGN - Does it support Access Point Infrastructure Mode ? Abdelmuhaimen Seaudi
2013-03-02 10:22 ` Pat Erley
2013-03-02 12:52 ` Abdelmuhaimen Seaudi
2013-03-02 10:27 ` Pat Erley
2013-03-02 12:47 ` Abdelmuhaimen Seaudi
2013-03-03 16:08 ` Dan Williams
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.