* [U-Boot] [PATCH 1/2] PHY: micrel: helper function for KSZ9031 [not found] <1371727592-21028-1-git-send-email-lsartre@adeneo-embedded.com> @ 2013-06-20 11:26 ` SARTRE Leo 2013-06-20 12:31 ` Otavio Salvador 2013-06-20 14:44 ` Stefano Babic 2013-06-20 11:26 ` [U-Boot] [PATCH 2/2] ARM: Congatec: Ethernet: Add support for cgtqmx6qeval SARTRE Leo 1 sibling, 2 replies; 5+ messages in thread From: SARTRE Leo @ 2013-06-20 11:26 UTC (permalink / raw) To: u-boot micrel.c: Add function ksz9031_phy_extended_write, helper to MDD register write micrel.h: Prototype and define MDD registers Signed-off-by: Leo Sartre <lsartre@adeneo-embedded.com> --- drivers/net/phy/micrel.c | 29 +++++++++++++++++++++++++++-- include/micrel.h | 7 +++++++ 2 files changed, 34 insertions(+), 2 deletions(-) diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c index 2a8b6cb..5b5c11b 100644 --- a/drivers/net/phy/micrel.c +++ b/drivers/net/phy/micrel.c @@ -85,7 +85,7 @@ static int ksz90xx_startup(struct phy_device *phydev) } #ifdef CONFIG_PHY_MICREL_KSZ9021 -/* +/** * KSZ9021 */ @@ -148,9 +148,34 @@ static struct phy_driver ksz9021_driver = { }; #endif -/* +/** * KSZ9031 */ + +/* PHY Registers */ +#define MII_KSZ9031_MMD_ACCES_CTRL 0x0d +#define MII_KSZ9031_MMD_REG_DATA 0x0e + +/* Accessors to extended registers*/ +int ksz9031_phy_extended_write(struct phy_device *phydev, + int devaddr, + int regnum, + u16 val) +{ + /*select register addr for mmd*/ + phy_write(phydev, MDIO_DEVAD_NONE, + MII_KSZ9031_MMD_ACCES_CTRL, devaddr); + /*select register for mmd*/ + phy_write(phydev, MDIO_DEVAD_NONE, + MII_KSZ9031_MMD_REG_DATA, regnum); + /*setup mode*/ + phy_write(phydev, MDIO_DEVAD_NONE, + MII_KSZ9031_MMD_ACCES_CTRL, (devaddr | 0xC000)); + /*write the value*/ + return phy_write(phydev, MDIO_DEVAD_NONE, + MII_KSZ9031_MMD_REG_DATA, val); +} + static struct phy_driver ksz9031_driver = { .name = "Micrel ksz9031", .uid = 0x221620, diff --git a/include/micrel.h b/include/micrel.h index 25e8a46..d63ff45 100644 --- a/include/micrel.h +++ b/include/micrel.h @@ -9,8 +9,15 @@ #define MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW 0x106 #define MII_KSZ9021_EXT_ANALOG_TEST 0x107 +#define MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW 0x4 +#define MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW 0x5 +#define MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW 0x6 +#define MII_KSZ9031_EXT_RGMII_CLOCK_SKEW 0x8 + struct phy_device; int ksz9021_phy_extended_write(struct phy_device *phydev, int regnum, u16 val); int ksz9021_phy_extended_read(struct phy_device *phydev, int regnum); +int ksz9031_phy_extended_write(struct phy_device *phydev, int devaddr, + int regnum, u16 val); #endif -- 1.7.10.4 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* [U-Boot] [PATCH 1/2] PHY: micrel: helper function for KSZ9031 2013-06-20 11:26 ` [U-Boot] [PATCH 1/2] PHY: micrel: helper function for KSZ9031 SARTRE Leo @ 2013-06-20 12:31 ` Otavio Salvador 2013-06-20 14:44 ` Stefano Babic 1 sibling, 0 replies; 5+ messages in thread From: Otavio Salvador @ 2013-06-20 12:31 UTC (permalink / raw) To: u-boot On Thu, Jun 20, 2013 at 8:26 AM, SARTRE Leo <lsartre@adeneo-embedded.com> wrote: > micrel.c: Add function ksz9031_phy_extended_write, helper to MDD > register write > micrel.h: Prototype and define MDD registers > > Signed-off-by: Leo Sartre <lsartre@adeneo-embedded.com> > --- > drivers/net/phy/micrel.c | 29 +++++++++++++++++++++++++++-- > include/micrel.h | 7 +++++++ > 2 files changed, 34 insertions(+), 2 deletions(-) > > diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c > index 2a8b6cb..5b5c11b 100644 > --- a/drivers/net/phy/micrel.c > +++ b/drivers/net/phy/micrel.c > @@ -85,7 +85,7 @@ static int ksz90xx_startup(struct phy_device *phydev) > } > #ifdef CONFIG_PHY_MICREL_KSZ9021 > > -/* > +/** > * KSZ9021 > */ Please drop this change; not need. > @@ -148,9 +148,34 @@ static struct phy_driver ksz9021_driver = { > }; > #endif > > -/* > +/** > * KSZ9031 > */ Please drop this change; not need. -- Otavio Salvador O.S. Systems http://www.ossystems.com.br http://projetos.ossystems.com.br Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750 ^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot] [PATCH 1/2] PHY: micrel: helper function for KSZ9031 2013-06-20 11:26 ` [U-Boot] [PATCH 1/2] PHY: micrel: helper function for KSZ9031 SARTRE Leo 2013-06-20 12:31 ` Otavio Salvador @ 2013-06-20 14:44 ` Stefano Babic 1 sibling, 0 replies; 5+ messages in thread From: Stefano Babic @ 2013-06-20 14:44 UTC (permalink / raw) To: u-boot Hi Joe, On 20/06/2013 13:26, SARTRE Leo wrote: > micrel.c: Add function ksz9031_phy_extended_write, helper to MDD > register write > micrel.h: Prototype and define MDD registers > > Signed-off-by: Leo Sartre <lsartre@adeneo-embedded.com> > --- > drivers/net/phy/micrel.c | 29 +++++++++++++++++++++++++++-- > include/micrel.h | 7 +++++++ > 2 files changed, 34 insertions(+), 2 deletions(-) > > diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c > index 2a8b6cb..5b5c11b 100644 > --- a/drivers/net/phy/micrel.c > +++ b/drivers/net/phy/micrel.c > @@ -85,7 +85,7 @@ static int ksz90xx_startup(struct phy_device *phydev) > } > #ifdef CONFIG_PHY_MICREL_KSZ9021 > > -/* > +/** > * KSZ9021 > */ > > @@ -148,9 +148,34 @@ static struct phy_driver ksz9021_driver = { > }; > #endif > > -/* > +/** > * KSZ9031 > */ > + > +/* PHY Registers */ > +#define MII_KSZ9031_MMD_ACCES_CTRL 0x0d > +#define MII_KSZ9031_MMD_REG_DATA 0x0e > + > +/* Accessors to extended registers*/ > +int ksz9031_phy_extended_write(struct phy_device *phydev, > + int devaddr, > + int regnum, > + u16 val) > +{ > + /*select register addr for mmd*/ > + phy_write(phydev, MDIO_DEVAD_NONE, > + MII_KSZ9031_MMD_ACCES_CTRL, devaddr); > + /*select register for mmd*/ > + phy_write(phydev, MDIO_DEVAD_NONE, > + MII_KSZ9031_MMD_REG_DATA, regnum); > + /*setup mode*/ > + phy_write(phydev, MDIO_DEVAD_NONE, > + MII_KSZ9031_MMD_ACCES_CTRL, (devaddr | 0xC000)); > + /*write the value*/ > + return phy_write(phydev, MDIO_DEVAD_NONE, > + MII_KSZ9031_MMD_REG_DATA, val); > +} > + > static struct phy_driver ksz9031_driver = { > .name = "Micrel ksz9031", > .uid = 0x221620, > diff --git a/include/micrel.h b/include/micrel.h > index 25e8a46..d63ff45 100644 > --- a/include/micrel.h > +++ b/include/micrel.h > @@ -9,8 +9,15 @@ > #define MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW 0x106 > #define MII_KSZ9021_EXT_ANALOG_TEST 0x107 > > +#define MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW 0x4 > +#define MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW 0x5 > +#define MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW 0x6 > +#define MII_KSZ9031_EXT_RGMII_CLOCK_SKEW 0x8 > + > struct phy_device; > int ksz9021_phy_extended_write(struct phy_device *phydev, int regnum, u16 val); > int ksz9021_phy_extended_read(struct phy_device *phydev, int regnum); > > +int ksz9031_phy_extended_write(struct phy_device *phydev, int devaddr, > + int regnum, u16 val); > #endif > This patchset belongs to two are, mainly i.MX (for Congatec) and to Network (this patch). Can you ACK/NACK this ? I will enqueue the other two patches in the meantime. To proceed, I propose I can merge then whole patchset into u-boot-imx to avoid to have inconsistent trees. Thanks, Stefano -- ===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de ===================================================================== ^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot] [PATCH 2/2] ARM: Congatec: Ethernet: Add support for cgtqmx6qeval [not found] <1371727592-21028-1-git-send-email-lsartre@adeneo-embedded.com> 2013-06-20 11:26 ` [U-Boot] [PATCH 1/2] PHY: micrel: helper function for KSZ9031 SARTRE Leo @ 2013-06-20 11:26 ` SARTRE Leo 2013-06-20 12:34 ` Otavio Salvador 1 sibling, 1 reply; 5+ messages in thread From: SARTRE Leo @ 2013-06-20 11:26 UTC (permalink / raw) To: u-boot cgtqmx6eval.c: add Micrel KSZ9031 Ethernet transceiver README : U-boot works both on SPI-NOR and SDcard Signed-off-by: Leo Sartre <lsartre@adeneo-embedded.com> --- board/congatec/cgtqmx6eval/README | 3 +- board/congatec/cgtqmx6eval/cgtqmx6eval.c | 112 ++++++++++++++++++++++++++++++ include/configs/cgtqmx6eval.h | 13 ++++ 3 files changed, 126 insertions(+), 2 deletions(-) diff --git a/board/congatec/cgtqmx6eval/README b/board/congatec/cgtqmx6eval/README index bbf0f75..5e76d2a 100644 --- a/board/congatec/cgtqmx6eval/README +++ b/board/congatec/cgtqmx6eval/README @@ -7,8 +7,7 @@ Conga-QEVAl Evaluation Carrier board with qmx6 quad module. 1. Boot source, boot from SD card --------------------------------- -This version of u-boot works only on the SD card. By default, the -Congatec board can boot only from the SPI-NOR. +By default, the Congatec board can boot only from the SPI-NOR. But, with the u-boot version provided with the board you can write boot registers to force the board to reboot and boot from the SD slot. If "bmode" command is not available from your pre-installed u-boot, these diff --git a/board/congatec/cgtqmx6eval/cgtqmx6eval.c b/board/congatec/cgtqmx6eval/cgtqmx6eval.c index f70f674..00088fb 100644 --- a/board/congatec/cgtqmx6eval/cgtqmx6eval.c +++ b/board/congatec/cgtqmx6eval/cgtqmx6eval.c @@ -30,6 +30,8 @@ #include <asm/imx-common/iomux-v3.h> #include <asm/imx-common/boot_mode.h> #include <mmc.h> +#include <micrel.h> +#include <miiphy.h> #include <fsl_esdhc.h> DECLARE_GLOBAL_DATA_PTR; @@ -40,6 +42,9 @@ DECLARE_GLOBAL_DATA_PTR; #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW |\ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) +#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) + int dram_init(void) { gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); @@ -76,6 +81,113 @@ iomux_v3_cfg_t const usdhc4_pads[] = { MX6_PAD_NANDF_D6__GPIO_2_6 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ }; +iomux_v3_cfg_t const enet_pads1[] = { + MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TXC__ENET_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD0__ENET_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD1__ENET_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD2__ENET_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD3__ENET_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_GPIO_0__CCM_CLKO | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_GPIO_3__CCM_CLKO2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL), + /* pin 35 - 1 (PHY_AD2) on reset */ + MX6_PAD_RGMII_RXC__GPIO_6_30 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* pin 32 - 1 - (MODE0) all */ + MX6_PAD_RGMII_RD0__GPIO_6_25 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* pin 31 - 1 - (MODE1) all */ + MX6_PAD_RGMII_RD1__GPIO_6_27 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* pin 28 - 1 - (MODE2) all */ + MX6_PAD_RGMII_RD2__GPIO_6_28 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* pin 27 - 1 - (MODE3) all */ + MX6_PAD_RGMII_RD3__GPIO_6_29 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */ + MX6_PAD_RGMII_RX_CTL__GPIO_6_24 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* pin 42 PHY nRST */ + MX6_PAD_EIM_D23__GPIO_3_23 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +iomux_v3_cfg_t const enet_pads2[] = { + MX6_PAD_RGMII_RXC__ENET_RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD0__ENET_RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD1__ENET_RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD2__ENET_RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD3__ENET_RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), +}; + +static void setup_iomux_enet(void) +{ + gpio_direction_output(IMX_GPIO_NR(3, 23), 0); + gpio_direction_output(IMX_GPIO_NR(6, 30), 1); + gpio_direction_output(IMX_GPIO_NR(6, 25), 1); + gpio_direction_output(IMX_GPIO_NR(6, 27), 1); + gpio_direction_output(IMX_GPIO_NR(6, 28), 1); + gpio_direction_output(IMX_GPIO_NR(6, 29), 1); + imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1)); + gpio_direction_output(IMX_GPIO_NR(6, 24), 1); + + /* Need delay 10ms according to KSZ9031 spec */ + udelay(1000 * 10); + gpio_set_value(IMX_GPIO_NR(3, 23), 1); + imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2)); +} + +int board_phy_config(struct phy_device *phydev) +{ + ksz9031_phy_extended_write(phydev, 2, + MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW, + 0x0000); + ksz9031_phy_extended_write(phydev, 2, + MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW, + 0x0000); + ksz9031_phy_extended_write(phydev, 2, + MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW, + 0xFFFF); + ksz9031_phy_extended_write(phydev, 2, + MII_KSZ9031_EXT_RGMII_CLOCK_SKEW, + 0x3FFF); + + phydev->drv->config(phydev); + + return 0; +} + +int board_eth_init(bd_t *bis) +{ + uint32_t base = IMX_FEC_BASE; + struct mii_dev *bus = NULL; + struct phy_device *phydev = NULL; + int ret; + + setup_iomux_enet(); + +#ifdef CONFIG_FEC_MXC + bus = fec_get_miibus(base, -1); + if (!bus) + return 0; + /* scan phy 6*/ + phydev = phy_find_by_mask(bus, (0xf << 6), PHY_INTERFACE_MODE_RGMII); + + if (!phydev) { + free(bus); + printf("No phy found\n"); + return 0; + } + printf("using phy@%d\n", phydev->addr); + ret = fec_probe(bis, -1, base, bus, phydev); + if (ret) { + printf("FEC MXC: %s:failed\n", __func__); + free(phydev); + free(bus); + } +#endif + return 0; +} + + static void setup_iomux_uart(void) { imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads)); diff --git a/include/configs/cgtqmx6eval.h b/include/configs/cgtqmx6eval.h index 1363858..60b7bec 100644 --- a/include/configs/cgtqmx6eval.h +++ b/include/configs/cgtqmx6eval.h @@ -66,6 +66,19 @@ #define CONFIG_CMD_FAT #define CONFIG_DOS_PARTITION +/* Ethernet Configs */ +#define CONFIG_CMD_PING +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_FEC_MXC +#define CONFIG_MII +#define IMX_FEC_BASE ENET_BASE_ADDR +#define CONFIG_FEC_XCV_TYPE RGMII +#define CONFIG_ETHPRIME "FEC" +#define CONFIG_FEC_MXC_PHYADDR 6 +#define CONFIG_PHYLIB +#define CONFIG_PHY_MICREL + /* Miscellaneous commands */ #define CONFIG_CMD_BMODE -- 1.7.10.4 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* [U-Boot] [PATCH 2/2] ARM: Congatec: Ethernet: Add support for cgtqmx6qeval 2013-06-20 11:26 ` [U-Boot] [PATCH 2/2] ARM: Congatec: Ethernet: Add support for cgtqmx6qeval SARTRE Leo @ 2013-06-20 12:34 ` Otavio Salvador 0 siblings, 0 replies; 5+ messages in thread From: Otavio Salvador @ 2013-06-20 12:34 UTC (permalink / raw) To: u-boot On Thu, Jun 20, 2013 at 8:26 AM, SARTRE Leo <lsartre@adeneo-embedded.com> wrote: > cgtqmx6eval.c: add Micrel KSZ9031 Ethernet transceiver > README : U-boot works both on SPI-NOR and SDcard > > Signed-off-by: Leo Sartre <lsartre@adeneo-embedded.com> > --- > board/congatec/cgtqmx6eval/README | 3 +- > board/congatec/cgtqmx6eval/cgtqmx6eval.c | 112 ++++++++++++++++++++++++++++++ > include/configs/cgtqmx6eval.h | 13 ++++ > 3 files changed, 126 insertions(+), 2 deletions(-) > > diff --git a/board/congatec/cgtqmx6eval/README b/board/congatec/cgtqmx6eval/README > index bbf0f75..5e76d2a 100644 > --- a/board/congatec/cgtqmx6eval/README > +++ b/board/congatec/cgtqmx6eval/README > @@ -7,8 +7,7 @@ Conga-QEVAl Evaluation Carrier board with qmx6 quad module. > 1. Boot source, boot from SD card > --------------------------------- > > -This version of u-boot works only on the SD card. By default, the > -Congatec board can boot only from the SPI-NOR. > +By default, the Congatec board can boot only from the SPI-NOR. > But, with the u-boot version provided with the board you can write boot > registers to force the board to reboot and boot from the SD slot. If > "bmode" command is not available from your pre-installed u-boot, these Please change this in another patch. This one you can add Stefano in Cc so he can apply it in his tree. > diff --git a/board/congatec/cgtqmx6eval/cgtqmx6eval.c b/board/congatec/cgtqmx6eval/cgtqmx6eval.c > index f70f674..00088fb 100644 > --- a/board/congatec/cgtqmx6eval/cgtqmx6eval.c > +++ b/board/congatec/cgtqmx6eval/cgtqmx6eval.c > @@ -30,6 +30,8 @@ > #include <asm/imx-common/iomux-v3.h> > #include <asm/imx-common/boot_mode.h> > #include <mmc.h> > +#include <micrel.h> > +#include <miiphy.h> > #include <fsl_esdhc.h> > > DECLARE_GLOBAL_DATA_PTR; > @@ -40,6 +42,9 @@ DECLARE_GLOBAL_DATA_PTR; > #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW |\ > PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) > > +#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ > + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) > + > int dram_init(void) > { > gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); > @@ -76,6 +81,113 @@ iomux_v3_cfg_t const usdhc4_pads[] = { > MX6_PAD_NANDF_D6__GPIO_2_6 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ > }; > > +iomux_v3_cfg_t const enet_pads1[] = { > + MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII_TXC__ENET_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII_TD0__ENET_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII_TD1__ENET_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII_TD2__ENET_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII_TD3__ENET_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_GPIO_0__CCM_CLKO | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_GPIO_3__CCM_CLKO2 | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL), > + /* pin 35 - 1 (PHY_AD2) on reset */ > + MX6_PAD_RGMII_RXC__GPIO_6_30 | MUX_PAD_CTRL(NO_PAD_CTRL), > + /* pin 32 - 1 - (MODE0) all */ > + MX6_PAD_RGMII_RD0__GPIO_6_25 | MUX_PAD_CTRL(NO_PAD_CTRL), > + /* pin 31 - 1 - (MODE1) all */ > + MX6_PAD_RGMII_RD1__GPIO_6_27 | MUX_PAD_CTRL(NO_PAD_CTRL), > + /* pin 28 - 1 - (MODE2) all */ > + MX6_PAD_RGMII_RD2__GPIO_6_28 | MUX_PAD_CTRL(NO_PAD_CTRL), > + /* pin 27 - 1 - (MODE3) all */ > + MX6_PAD_RGMII_RD3__GPIO_6_29 | MUX_PAD_CTRL(NO_PAD_CTRL), > + /* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */ > + MX6_PAD_RGMII_RX_CTL__GPIO_6_24 | MUX_PAD_CTRL(NO_PAD_CTRL), > + /* pin 42 PHY nRST */ > + MX6_PAD_EIM_D23__GPIO_3_23 | MUX_PAD_CTRL(NO_PAD_CTRL), > +}; > + > +iomux_v3_cfg_t const enet_pads2[] = { > + MX6_PAD_RGMII_RXC__ENET_RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII_RD0__ENET_RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII_RD1__ENET_RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII_RD2__ENET_RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII_RD3__ENET_RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), > + MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), > +}; > + > +static void setup_iomux_enet(void) > +{ > + gpio_direction_output(IMX_GPIO_NR(3, 23), 0); > + gpio_direction_output(IMX_GPIO_NR(6, 30), 1); > + gpio_direction_output(IMX_GPIO_NR(6, 25), 1); > + gpio_direction_output(IMX_GPIO_NR(6, 27), 1); > + gpio_direction_output(IMX_GPIO_NR(6, 28), 1); > + gpio_direction_output(IMX_GPIO_NR(6, 29), 1); > + imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1)); > + gpio_direction_output(IMX_GPIO_NR(6, 24), 1); > + > + /* Need delay 10ms according to KSZ9031 spec */ > + udelay(1000 * 10); > + gpio_set_value(IMX_GPIO_NR(3, 23), 1); > + imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2)); > +} > + > +int board_phy_config(struct phy_device *phydev) > +{ > + ksz9031_phy_extended_write(phydev, 2, > + MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW, > + 0x0000); > + ksz9031_phy_extended_write(phydev, 2, > + MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW, > + 0x0000); > + ksz9031_phy_extended_write(phydev, 2, > + MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW, > + 0xFFFF); > + ksz9031_phy_extended_write(phydev, 2, > + MII_KSZ9031_EXT_RGMII_CLOCK_SKEW, > + 0x3FFF); > + > + phydev->drv->config(phydev); > + > + return 0; > +} > + > +int board_eth_init(bd_t *bis) > +{ > + uint32_t base = IMX_FEC_BASE; > + struct mii_dev *bus = NULL; > + struct phy_device *phydev = NULL; > + int ret; > + > + setup_iomux_enet(); > + > +#ifdef CONFIG_FEC_MXC Shouldn't this cover the whole function? > + bus = fec_get_miibus(base, -1); > + if (!bus) > + return 0; > + /* scan phy 6*/ > + phydev = phy_find_by_mask(bus, (0xf << 6), PHY_INTERFACE_MODE_RGMII); > + > + if (!phydev) { > + free(bus); > + printf("No phy found\n"); > + return 0; > + } > + printf("using phy at %d\n", phydev->addr); > + ret = fec_probe(bis, -1, base, bus, phydev); > + if (ret) { > + printf("FEC MXC: %s:failed\n", __func__); > + free(phydev); > + free(bus); > + } > +#endif > + return 0; > +} -- Otavio Salvador O.S. Systems http://www.ossystems.com.br http://projetos.ossystems.com.br Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750 ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2013-06-20 14:44 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <1371727592-21028-1-git-send-email-lsartre@adeneo-embedded.com>
2013-06-20 11:26 ` [U-Boot] [PATCH 1/2] PHY: micrel: helper function for KSZ9031 SARTRE Leo
2013-06-20 12:31 ` Otavio Salvador
2013-06-20 14:44 ` Stefano Babic
2013-06-20 11:26 ` [U-Boot] [PATCH 2/2] ARM: Congatec: Ethernet: Add support for cgtqmx6qeval SARTRE Leo
2013-06-20 12:34 ` Otavio Salvador
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.