* [U-Boot] [PATCH v3 0/2] Add Arndale board support
@ 2013-07-02 4:41 Inderpal Singh
2013-07-02 4:41 ` [U-Boot] [PATCH v3 1/2] exynos5250: Add arndale " Inderpal Singh
` (2 more replies)
0 siblings, 3 replies; 5+ messages in thread
From: Inderpal Singh @ 2013-07-02 4:41 UTC (permalink / raw)
To: u-boot
The Arndale board is based on samsung's exynos5250 SOC.
For spl generation, it depends on the patch at [5].
First patch provides the basic arndale board support. The second patch
adds the MMC support.
Changes in v2:
- split from earlier patchset at [3] as per Minkyu
- Removed checkpatch errors pointed out by Wolfgang
- rebased to latest u-boot-samsung master branch
- created mmc_boot.c to remove dependency on consolidation
patch at [4]
- split the mmc support to new patch as it depends on [2]
[1] http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/162883
[2] http://comments.gmane.org/gmane.comp.boot-loaders.u-boot/159887
[3] http://comments.gmane.org/gmane.comp.boot-loaders.u-boot/157101
[4] http://comments.gmane.org/gmane.comp.boot-loaders.u-boot/156272
Changes in v3:
- Used dt based serial
- rebased to latest u-boot-samsung master branch
[5] http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/164824
Inderpal Singh (2):
exynos5250: Add arndale board support
exynos5250: arndale: Add mmc support
MAINTAINERS | 4 +
board/samsung/arndale/Makefile | 58 +++
board/samsung/arndale/arndale.c | 117 ++++++
board/samsung/arndale/arndale_spl.c | 66 +++
board/samsung/arndale/clock_init.c | 655 ++++++++++++++++++++++++++++++
board/samsung/arndale/clock_init.h | 149 +++++++
board/samsung/arndale/dmc_common.c | 199 +++++++++
board/samsung/arndale/dmc_init_ddr3.c | 228 +++++++++++
board/samsung/arndale/lowlevel_init.S | 92 +++++
board/samsung/arndale/mmc_boot.c | 58 +++
board/samsung/arndale/setup.h | 569 ++++++++++++++++++++++++++
board/samsung/dts/exynos5250-arndale.dts | 41 ++
boards.cfg | 1 +
include/configs/arndale.h | 36 ++
14 files changed, 2273 insertions(+)
create mode 100644 board/samsung/arndale/Makefile
create mode 100644 board/samsung/arndale/arndale.c
create mode 100644 board/samsung/arndale/arndale_spl.c
create mode 100644 board/samsung/arndale/clock_init.c
create mode 100644 board/samsung/arndale/clock_init.h
create mode 100644 board/samsung/arndale/dmc_common.c
create mode 100644 board/samsung/arndale/dmc_init_ddr3.c
create mode 100644 board/samsung/arndale/lowlevel_init.S
create mode 100644 board/samsung/arndale/mmc_boot.c
create mode 100644 board/samsung/arndale/setup.h
create mode 100644 board/samsung/dts/exynos5250-arndale.dts
create mode 100644 include/configs/arndale.h
--
1.7.9.5
^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot] [PATCH v3 1/2] exynos5250: Add arndale board support
2013-07-02 4:41 [U-Boot] [PATCH v3 0/2] Add Arndale board support Inderpal Singh
@ 2013-07-02 4:41 ` Inderpal Singh
2013-07-02 6:36 ` Minkyu Kang
2013-07-02 4:41 ` [U-Boot] [PATCH v3 2/2] exynos5250: arndale: Add mmc support Inderpal Singh
2013-07-02 5:55 ` [U-Boot] [PATCH v3 0/2] Add Arndale board support Chander Kashyap
2 siblings, 1 reply; 5+ messages in thread
From: Inderpal Singh @ 2013-07-02 4:41 UTC (permalink / raw)
To: u-boot
Arndale board is based on samsung's exynos5250 soc.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
---
MAINTAINERS | 4 +
board/samsung/arndale/Makefile | 58 +++
board/samsung/arndale/arndale.c | 103 +++++
board/samsung/arndale/arndale_spl.c | 66 +++
board/samsung/arndale/clock_init.c | 655 ++++++++++++++++++++++++++++++
board/samsung/arndale/clock_init.h | 149 +++++++
board/samsung/arndale/dmc_common.c | 199 +++++++++
board/samsung/arndale/dmc_init_ddr3.c | 228 +++++++++++
board/samsung/arndale/lowlevel_init.S | 92 +++++
board/samsung/arndale/mmc_boot.c | 58 +++
board/samsung/arndale/setup.h | 569 ++++++++++++++++++++++++++
board/samsung/dts/exynos5250-arndale.dts | 23 ++
boards.cfg | 1 +
include/configs/arndale.h | 36 ++
14 files changed, 2241 insertions(+)
create mode 100644 board/samsung/arndale/Makefile
create mode 100644 board/samsung/arndale/arndale.c
create mode 100644 board/samsung/arndale/arndale_spl.c
create mode 100644 board/samsung/arndale/clock_init.c
create mode 100644 board/samsung/arndale/clock_init.h
create mode 100644 board/samsung/arndale/dmc_common.c
create mode 100644 board/samsung/arndale/dmc_init_ddr3.c
create mode 100644 board/samsung/arndale/lowlevel_init.S
create mode 100644 board/samsung/arndale/mmc_boot.c
create mode 100644 board/samsung/arndale/setup.h
create mode 100644 board/samsung/dts/exynos5250-arndale.dts
create mode 100644 include/configs/arndale.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 7820375..e1b6808 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -743,6 +743,10 @@ Chander Kashyap <k.chander@samsung.com>
SMDKV310 ARM ARMV7 (EXYNOS4210 SoC)
SMDK5250 ARM ARMV7 (EXYNOS5250 SoC)
+Inderpal Singh <inderpal.singh@linaro.org>
+
+ Arndale ARM ARMV7 (EXYNOS5250 SoC)
+
Lukasz Majewski <l.majewski@samsung.com>
trats ARM ARMV7 (EXYNOS4210 SoC)
diff --git a/board/samsung/arndale/Makefile b/board/samsung/arndale/Makefile
new file mode 100644
index 0000000..6a15d34
--- /dev/null
+++ b/board/samsung/arndale/Makefile
@@ -0,0 +1,58 @@
+#
+# Copyright (C) 2013 Samsung Electronics
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+SOBJS := lowlevel_init.o
+
+COBJS := clock_init.o
+COBJS += dmc_common.o dmc_init_ddr3.o
+COBJS += arndale_spl.o
+
+ifndef CONFIG_SPL_BUILD
+COBJS += arndale.o
+endif
+
+ifdef CONFIG_SPL_BUILD
+COBJS += mmc_boot.o
+endif
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS))
+
+ALL := $(obj).depend $(LIB)
+
+all: $(ALL)
+
+$(LIB): $(OBJS)
+ $(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/samsung/arndale/arndale.c b/board/samsung/arndale/arndale.c
new file mode 100644
index 0000000..627583b
--- /dev/null
+++ b/board/samsung/arndale/arndale.c
@@ -0,0 +1,103 @@
+/*
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/power.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
+ return 0;
+}
+
+int dram_init(void)
+{
+ int i;
+ u32 addr;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
+ gd->ram_size += get_ram_size((long *)addr, SDRAM_BANK_SIZE);
+ }
+ return 0;
+}
+
+int power_init_board(void)
+{
+ set_ps_hold_ctrl();
+ return 0;
+}
+
+void dram_init_banksize(void)
+{
+ int i;
+ u32 addr, size;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
+ size = get_ram_size((long *)addr, SDRAM_BANK_SIZE);
+
+ gd->bd->bi_dram[i].start = addr;
+ gd->bd->bi_dram[i].size = size;
+ }
+}
+
+static int board_uart_init(void)
+{
+ int err, uart_id, ret = 0;
+
+ for (uart_id = PERIPH_ID_UART0; uart_id <= PERIPH_ID_UART3; uart_id++) {
+ err = exynos_pinmux_config(uart_id, PINMUX_FLAG_NONE);
+ if (err) {
+ debug("UART%d not configured\n",
+ (uart_id - PERIPH_ID_UART0));
+ ret |= err;
+ }
+ }
+ return ret;
+}
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+int board_early_init_f(void)
+{
+ int err;
+ err = board_uart_init();
+ if (err) {
+ debug("UART init failed\n");
+ return err;
+ }
+ return err;
+}
+#endif
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard(void)
+{
+ printf("\nBoard: Arndale\n");
+
+ return 0;
+}
+#endif
+
diff --git a/board/samsung/arndale/arndale_spl.c b/board/samsung/arndale/arndale_spl.c
new file mode 100644
index 0000000..8135708
--- /dev/null
+++ b/board/samsung/arndale/arndale_spl.c
@@ -0,0 +1,66 @@
+/*
+ * Copyright (c) 2012 The Chromium OS Authors.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/spl.h>
+
+#define SIGNATURE 0xdeadbeef
+
+/* Parameters of early board initialization in SPL */
+static struct spl_machine_param machine_param
+ __attribute__((section(".machine_param"))) = {
+ .signature = SIGNATURE,
+ .version = 1,
+ .params = "vmubfasirM",
+ .size = sizeof(machine_param),
+
+ .mem_iv_size = 0x1f,
+ .mem_type = DDR_MODE_DDR3,
+
+ /*
+ * Set uboot_size to 0x100000 bytes.
+ *
+ * This is an overly conservative value chosen to accommodate all
+ * possible U-Boot image. You are advised to set this value to a
+ * smaller realistic size via scripts that modifies the .machine_param
+ * section of output U-Boot image.
+ */
+ .uboot_size = 0x100000,
+
+ .boot_source = BOOT_MODE_OM,
+ .frequency_mhz = 800,
+ .arm_freq_mhz = 1000,
+ .serial_base = 0x12c30000,
+ .i2c_base = 0x12c60000,
+ .mem_manuf = MEM_MANUF_SAMSUNG,
+};
+
+struct spl_machine_param *spl_get_machine_params(void)
+{
+ if (machine_param.signature != SIGNATURE) {
+ /* Will hang if SIGNATURE dont match */
+ while (1)
+ ;
+ }
+
+ return &machine_param;
+}
diff --git a/board/samsung/arndale/clock_init.c b/board/samsung/arndale/clock_init.c
new file mode 100644
index 0000000..a9b0bbd
--- /dev/null
+++ b/board/samsung/arndale/clock_init.c
@@ -0,0 +1,655 @@
+/*
+ * Clock setup for Arndale board based on EXYNOS5
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/spl.h>
+
+#include "clock_init.h"
+#include "setup.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct arm_clk_ratios arm_clk_ratios[] = {
+ {
+ .arm_freq_mhz = 600,
+
+ .apll_mdiv = 0xc8,
+ .apll_pdiv = 0x4,
+ .apll_sdiv = 0x1,
+
+ .arm2_ratio = 0x0,
+ .apll_ratio = 0x1,
+ .pclk_dbg_ratio = 0x1,
+ .atb_ratio = 0x2,
+ .periph_ratio = 0x7,
+ .acp_ratio = 0x7,
+ .cpud_ratio = 0x1,
+ .arm_ratio = 0x0,
+ }, {
+ .arm_freq_mhz = 800,
+
+ .apll_mdiv = 0x64,
+ .apll_pdiv = 0x3,
+ .apll_sdiv = 0x0,
+
+ .arm2_ratio = 0x0,
+ .apll_ratio = 0x1,
+ .pclk_dbg_ratio = 0x1,
+ .atb_ratio = 0x3,
+ .periph_ratio = 0x7,
+ .acp_ratio = 0x7,
+ .cpud_ratio = 0x2,
+ .arm_ratio = 0x0,
+ }, {
+ .arm_freq_mhz = 1000,
+
+ .apll_mdiv = 0x7d,
+ .apll_pdiv = 0x3,
+ .apll_sdiv = 0x0,
+
+ .arm2_ratio = 0x0,
+ .apll_ratio = 0x1,
+ .pclk_dbg_ratio = 0x1,
+ .atb_ratio = 0x4,
+ .periph_ratio = 0x7,
+ .acp_ratio = 0x7,
+ .cpud_ratio = 0x2,
+ .arm_ratio = 0x0,
+ }, {
+ .arm_freq_mhz = 1200,
+
+ .apll_mdiv = 0x96,
+ .apll_pdiv = 0x3,
+ .apll_sdiv = 0x0,
+
+ .arm2_ratio = 0x0,
+ .apll_ratio = 0x3,
+ .pclk_dbg_ratio = 0x1,
+ .atb_ratio = 0x5,
+ .periph_ratio = 0x7,
+ .acp_ratio = 0x7,
+ .cpud_ratio = 0x3,
+ .arm_ratio = 0x0,
+ }, {
+ .arm_freq_mhz = 1400,
+
+ .apll_mdiv = 0xaf,
+ .apll_pdiv = 0x3,
+ .apll_sdiv = 0x0,
+
+ .arm2_ratio = 0x0,
+ .apll_ratio = 0x3,
+ .pclk_dbg_ratio = 0x1,
+ .atb_ratio = 0x6,
+ .periph_ratio = 0x7,
+ .acp_ratio = 0x7,
+ .cpud_ratio = 0x3,
+ .arm_ratio = 0x0,
+ }, {
+ .arm_freq_mhz = 1700,
+
+ .apll_mdiv = 0x1a9,
+ .apll_pdiv = 0x6,
+ .apll_sdiv = 0x0,
+
+ .arm2_ratio = 0x0,
+ .apll_ratio = 0x3,
+ .pclk_dbg_ratio = 0x1,
+ .atb_ratio = 0x6,
+ .periph_ratio = 0x7,
+ .acp_ratio = 0x7,
+ .cpud_ratio = 0x3,
+ .arm_ratio = 0x0,
+ }
+};
+struct mem_timings mem_timings[] = {
+ {
+ .mem_manuf = MEM_MANUF_ELPIDA,
+ .mem_type = DDR_MODE_DDR3,
+ .frequency_mhz = 800,
+ .mpll_mdiv = 0xc8,
+ .mpll_pdiv = 0x3,
+ .mpll_sdiv = 0x0,
+ .cpll_mdiv = 0xde,
+ .cpll_pdiv = 0x4,
+ .cpll_sdiv = 0x2,
+ .gpll_mdiv = 0x215,
+ .gpll_pdiv = 0xc,
+ .gpll_sdiv = 0x1,
+ .epll_mdiv = 0x60,
+ .epll_pdiv = 0x3,
+ .epll_sdiv = 0x3,
+ .vpll_mdiv = 0x96,
+ .vpll_pdiv = 0x3,
+ .vpll_sdiv = 0x2,
+
+ .bpll_mdiv = 0x64,
+ .bpll_pdiv = 0x3,
+ .bpll_sdiv = 0x0,
+ .pclk_cdrex_ratio = 0x5,
+ .direct_cmd_msr = {
+ 0x00020018, 0x00030000, 0x00010042, 0x00000d70
+ },
+ .timing_ref = 0x000000bb,
+ .timing_row = 0x8c36650e,
+ .timing_data = 0x3630580b,
+ .timing_power = 0x41000a44,
+ .phy0_dqs = 0x08080808,
+ .phy1_dqs = 0x08080808,
+ .phy0_dq = 0x08080808,
+ .phy1_dq = 0x08080808,
+ .phy0_tFS = 0x4,
+ .phy1_tFS = 0x4,
+ .phy0_pulld_dqs = 0xf,
+ .phy1_pulld_dqs = 0xf,
+
+ .lpddr3_ctrl_phy_reset = 0x1,
+ .ctrl_start_point = 0x10,
+ .ctrl_inc = 0x10,
+ .ctrl_start = 0x1,
+ .ctrl_dll_on = 0x1,
+ .ctrl_ref = 0x8,
+
+ .ctrl_force = 0x1a,
+ .ctrl_rdlat = 0x0b,
+ .ctrl_bstlen = 0x08,
+
+ .fp_resync = 0x8,
+ .iv_size = 0x7,
+ .dfi_init_start = 1,
+ .aref_en = 1,
+
+ .rd_fetch = 0x3,
+
+ .zq_mode_dds = 0x7,
+ .zq_mode_term = 0x1,
+ .zq_mode_noterm = 0,
+
+ /*
+ * Dynamic Clock: Always Running
+ * Memory Burst length: 8
+ * Number of chips: 1
+ * Memory Bus width: 32 bit
+ * Memory Type: DDR3
+ * Additional Latancy for PLL: 0 Cycle
+ */
+ .memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
+ DMC_MEMCONTROL_DPWRDN_DISABLE |
+ DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
+ DMC_MEMCONTROL_TP_DISABLE |
+ DMC_MEMCONTROL_DSREF_ENABLE |
+ DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
+ DMC_MEMCONTROL_MEM_TYPE_DDR3 |
+ DMC_MEMCONTROL_MEM_WIDTH_32BIT |
+ DMC_MEMCONTROL_NUM_CHIP_1 |
+ DMC_MEMCONTROL_BL_8 |
+ DMC_MEMCONTROL_PZQ_DISABLE |
+ DMC_MEMCONTROL_MRR_BYTE_7_0,
+ .memconfig = DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED |
+ DMC_MEMCONFIGx_CHIP_COL_10 |
+ DMC_MEMCONFIGx_CHIP_ROW_15 |
+ DMC_MEMCONFIGx_CHIP_BANK_8,
+ .membaseconfig0 = DMC_MEMBASECONFIG_VAL(0x40),
+ .membaseconfig1 = DMC_MEMBASECONFIG_VAL(0x80),
+ .prechconfig_tp_cnt = 0xff,
+ .dpwrdn_cyc = 0xff,
+ .dsref_cyc = 0xffff,
+ .concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
+ DMC_CONCONTROL_TIMEOUT_LEVEL0 |
+ DMC_CONCONTROL_RD_FETCH_DISABLE |
+ DMC_CONCONTROL_EMPTY_DISABLE |
+ DMC_CONCONTROL_AREF_EN_DISABLE |
+ DMC_CONCONTROL_IO_PD_CON_DISABLE,
+ .dmc_channels = 2,
+ .chips_per_channel = 2,
+ .chips_to_configure = 1,
+ .send_zq_init = 1,
+ .impedance = IMP_OUTPUT_DRV_30_OHM,
+ .gate_leveling_enable = 0,
+ }, {
+ .mem_manuf = MEM_MANUF_SAMSUNG,
+ .mem_type = DDR_MODE_DDR3,
+ .frequency_mhz = 800,
+ .mpll_mdiv = 0xc8,
+ .mpll_pdiv = 0x3,
+ .mpll_sdiv = 0x0,
+ .cpll_mdiv = 0xde,
+ .cpll_pdiv = 0x4,
+ .cpll_sdiv = 0x2,
+ .gpll_mdiv = 0x215,
+ .gpll_pdiv = 0xc,
+ .gpll_sdiv = 0x1,
+ .epll_mdiv = 0x60,
+ .epll_pdiv = 0x3,
+ .epll_sdiv = 0x3,
+ .vpll_mdiv = 0x96,
+ .vpll_pdiv = 0x3,
+ .vpll_sdiv = 0x2,
+
+ .bpll_mdiv = 0x64,
+ .bpll_pdiv = 0x3,
+ .bpll_sdiv = 0x0,
+ .pclk_cdrex_ratio = 0x5,
+ .direct_cmd_msr = {
+ 0x00020018, 0x00030000, 0x00010000, 0x00000d70
+ },
+ .timing_ref = 0x000000bb,
+ .timing_row = 0x8c36650e,
+ .timing_data = 0x3630580b,
+ .timing_power = 0x41000a44,
+ .phy0_dqs = 0x08080808,
+ .phy1_dqs = 0x08080808,
+ .phy0_dq = 0x08080808,
+ .phy1_dq = 0x08080808,
+ .phy0_tFS = 0x8,
+ .phy1_tFS = 0x8,
+ .phy0_pulld_dqs = 0xf,
+ .phy1_pulld_dqs = 0xf,
+
+ .lpddr3_ctrl_phy_reset = 0x1,
+ .ctrl_start_point = 0x10,
+ .ctrl_inc = 0x10,
+ .ctrl_start = 0x1,
+ .ctrl_dll_on = 0x1,
+ .ctrl_ref = 0x8,
+
+ .ctrl_force = 0x1a,
+ .ctrl_rdlat = 0x0b,
+ .ctrl_bstlen = 0x08,
+
+ .fp_resync = 0x8,
+ .iv_size = 0x7,
+ .dfi_init_start = 1,
+ .aref_en = 1,
+
+ .rd_fetch = 0x3,
+
+ .zq_mode_dds = 0x5,
+ .zq_mode_term = 0x1,
+ .zq_mode_noterm = 1,
+
+ /*
+ * Dynamic Clock: Always Running
+ * Memory Burst length: 8
+ * Number of chips: 1
+ * Memory Bus width: 32 bit
+ * Memory Type: DDR3
+ * Additional Latancy for PLL: 0 Cycle
+ */
+ .memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
+ DMC_MEMCONTROL_DPWRDN_DISABLE |
+ DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
+ DMC_MEMCONTROL_TP_DISABLE |
+ DMC_MEMCONTROL_DSREF_ENABLE |
+ DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
+ DMC_MEMCONTROL_MEM_TYPE_DDR3 |
+ DMC_MEMCONTROL_MEM_WIDTH_32BIT |
+ DMC_MEMCONTROL_NUM_CHIP_1 |
+ DMC_MEMCONTROL_BL_8 |
+ DMC_MEMCONTROL_PZQ_DISABLE |
+ DMC_MEMCONTROL_MRR_BYTE_7_0,
+ .memconfig = DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED |
+ DMC_MEMCONFIGx_CHIP_COL_10 |
+ DMC_MEMCONFIGx_CHIP_ROW_15 |
+ DMC_MEMCONFIGx_CHIP_BANK_8,
+ .membaseconfig0 = DMC_MEMBASECONFIG_VAL(0x40),
+ .membaseconfig1 = DMC_MEMBASECONFIG_VAL(0x80),
+ .prechconfig_tp_cnt = 0xff,
+ .dpwrdn_cyc = 0xff,
+ .dsref_cyc = 0xffff,
+ .concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
+ DMC_CONCONTROL_TIMEOUT_LEVEL0 |
+ DMC_CONCONTROL_RD_FETCH_DISABLE |
+ DMC_CONCONTROL_EMPTY_DISABLE |
+ DMC_CONCONTROL_AREF_EN_DISABLE |
+ DMC_CONCONTROL_IO_PD_CON_DISABLE,
+ .dmc_channels = 2,
+ .chips_per_channel = 2,
+ .chips_to_configure = 1,
+ .send_zq_init = 1,
+ .impedance = IMP_OUTPUT_DRV_40_OHM,
+ .gate_leveling_enable = 1,
+ }
+};
+
+/**
+ * Get the required memory type and speed (SPL version).
+ *
+ * In SPL we have no device tree, so we use the machine parameters
+ *
+ * @param mem_type Returns memory type
+ * @param frequency_mhz Returns memory speed in MHz
+ * @param arm_freq Returns ARM clock speed in MHz
+ * @param mem_manuf Return Memory Manufacturer name
+ * @return 0 if all ok
+ */
+static int clock_get_mem_selection(enum ddr_mode *mem_type,
+ unsigned *frequency_mhz, unsigned *arm_freq,
+ enum mem_manuf *mem_manuf)
+{
+ struct spl_machine_param *params;
+
+ params = spl_get_machine_params();
+ *mem_type = params->mem_type;
+ *frequency_mhz = params->frequency_mhz;
+ *arm_freq = params->arm_freq_mhz;
+ *mem_manuf = params->mem_manuf;
+
+ return 0;
+}
+
+/* Get the ratios for setting ARM clock */
+struct arm_clk_ratios *get_arm_ratios(void)
+{
+ struct arm_clk_ratios *arm_ratio;
+ enum ddr_mode mem_type;
+ enum mem_manuf mem_manuf;
+ unsigned frequency_mhz, arm_freq;
+ int i;
+
+ if (clock_get_mem_selection(&mem_type, &frequency_mhz,
+ &arm_freq, &mem_manuf))
+ ;
+ for (i = 0, arm_ratio = arm_clk_ratios; i < ARRAY_SIZE(arm_clk_ratios);
+ i++, arm_ratio++) {
+ if (arm_ratio->arm_freq_mhz == arm_freq)
+ return arm_ratio;
+ }
+
+ /* will hang if failed to find clock ratio */
+ while (1)
+ ;
+
+ return NULL;
+}
+
+struct mem_timings *clock_get_mem_timings(void)
+{
+ struct mem_timings *mem;
+ enum ddr_mode mem_type;
+ enum mem_manuf mem_manuf;
+ unsigned frequency_mhz, arm_freq;
+ int i;
+
+ if (!clock_get_mem_selection(&mem_type, &frequency_mhz,
+ &arm_freq, &mem_manuf)) {
+ for (i = 0, mem = mem_timings; i < ARRAY_SIZE(mem_timings);
+ i++, mem++) {
+ if (mem->mem_type == mem_type &&
+ mem->frequency_mhz == frequency_mhz &&
+ mem->mem_manuf == mem_manuf)
+ return mem;
+ }
+ }
+
+ /* will hang if failed to find memory timings */
+ while (1)
+ ;
+
+ return NULL;
+}
+
+void system_clock_init()
+{
+ struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
+ struct mem_timings *mem;
+ struct arm_clk_ratios *arm_clk_ratio;
+ u32 val, tmp;
+
+ mem = clock_get_mem_timings();
+ arm_clk_ratio = get_arm_ratios();
+
+ clrbits_le32(&clk->src_cpu, MUX_APLL_SEL_MASK);
+ do {
+ val = readl(&clk->mux_stat_cpu);
+ } while ((val | MUX_APLL_SEL_MASK) != val);
+
+ clrbits_le32(&clk->src_core1, MUX_MPLL_SEL_MASK);
+ do {
+ val = readl(&clk->mux_stat_core1);
+ } while ((val | MUX_MPLL_SEL_MASK) != val);
+
+ clrbits_le32(&clk->src_core1, MUX_CPLL_SEL_MASK);
+ clrbits_le32(&clk->src_core1, MUX_EPLL_SEL_MASK);
+ clrbits_le32(&clk->src_core1, MUX_VPLL_SEL_MASK);
+ clrbits_le32(&clk->src_core1, MUX_GPLL_SEL_MASK);
+ tmp = MUX_CPLL_SEL_MASK | MUX_EPLL_SEL_MASK | MUX_VPLL_SEL_MASK
+ | MUX_GPLL_SEL_MASK;
+ do {
+ val = readl(&clk->mux_stat_top2);
+ } while ((val | tmp) != val);
+
+ clrbits_le32(&clk->src_cdrex, MUX_BPLL_SEL_MASK);
+ do {
+ val = readl(&clk->mux_stat_cdrex);
+ } while ((val | MUX_BPLL_SEL_MASK) != val);
+
+ /* PLL locktime */
+ writel(APLL_LOCK_VAL, &clk->apll_lock);
+
+ writel(MPLL_LOCK_VAL, &clk->mpll_lock);
+
+ writel(BPLL_LOCK_VAL, &clk->bpll_lock);
+
+ writel(CPLL_LOCK_VAL, &clk->cpll_lock);
+
+ writel(GPLL_LOCK_VAL, &clk->gpll_lock);
+
+ writel(EPLL_LOCK_VAL, &clk->epll_lock);
+
+ writel(VPLL_LOCK_VAL, &clk->vpll_lock);
+
+ writel(CLK_REG_DISABLE, &clk->pll_div2_sel);
+
+ writel(MUX_HPM_SEL_MASK, &clk->src_cpu);
+ do {
+ val = readl(&clk->mux_stat_cpu);
+ } while ((val | HPM_SEL_SCLK_MPLL) != val);
+
+ val = arm_clk_ratio->arm2_ratio << 28
+ | arm_clk_ratio->apll_ratio << 24
+ | arm_clk_ratio->pclk_dbg_ratio << 20
+ | arm_clk_ratio->atb_ratio << 16
+ | arm_clk_ratio->periph_ratio << 12
+ | arm_clk_ratio->acp_ratio << 8
+ | arm_clk_ratio->cpud_ratio << 4
+ | arm_clk_ratio->arm_ratio;
+ writel(val, &clk->div_cpu0);
+ do {
+ val = readl(&clk->div_stat_cpu0);
+ } while (0 != val);
+
+ writel(CLK_DIV_CPU1_VAL, &clk->div_cpu1);
+ do {
+ val = readl(&clk->div_stat_cpu1);
+ } while (0 != val);
+
+ /* Set APLL */
+ writel(APLL_CON1_VAL, &clk->apll_con1);
+ val = set_pll(arm_clk_ratio->apll_mdiv, arm_clk_ratio->apll_pdiv,
+ arm_clk_ratio->apll_sdiv);
+ writel(val, &clk->apll_con0);
+ while (readl(&clk->apll_con0) & APLL_CON0_LOCKED)
+ ;
+
+ /* Set MPLL */
+ writel(MPLL_CON1_VAL, &clk->mpll_con1);
+ val = set_pll(mem->mpll_mdiv, mem->mpll_pdiv, mem->mpll_sdiv);
+ writel(val, &clk->mpll_con0);
+ while (readl(&clk->mpll_con0) & MPLL_CON0_LOCKED)
+ ;
+
+ /* Set BPLL */
+ writel(BPLL_CON1_VAL, &clk->bpll_con1);
+ val = set_pll(mem->bpll_mdiv, mem->bpll_pdiv, mem->bpll_sdiv);
+ writel(val, &clk->bpll_con0);
+ while (readl(&clk->bpll_con0) & BPLL_CON0_LOCKED)
+ ;
+
+ /* Set CPLL */
+ writel(CPLL_CON1_VAL, &clk->cpll_con1);
+ val = set_pll(mem->cpll_mdiv, mem->cpll_pdiv, mem->cpll_sdiv);
+ writel(val, &clk->cpll_con0);
+ while (readl(&clk->cpll_con0) & CPLL_CON0_LOCKED)
+ ;
+
+ /* Set GPLL */
+ writel(GPLL_CON1_VAL, &clk->gpll_con1);
+ val = set_pll(mem->gpll_mdiv, mem->gpll_pdiv, mem->gpll_sdiv);
+ writel(val, &clk->gpll_con0);
+ while (readl(&clk->gpll_con0) & GPLL_CON0_LOCKED)
+ ;
+
+ /* Set EPLL */
+ writel(EPLL_CON2_VAL, &clk->epll_con2);
+ writel(EPLL_CON1_VAL, &clk->epll_con1);
+ val = set_pll(mem->epll_mdiv, mem->epll_pdiv, mem->epll_sdiv);
+ writel(val, &clk->epll_con0);
+ while (readl(&clk->epll_con0) & EPLL_CON0_LOCKED)
+ ;
+
+ /* Set VPLL */
+ writel(VPLL_CON2_VAL, &clk->vpll_con2);
+ writel(VPLL_CON1_VAL, &clk->vpll_con1);
+ val = set_pll(mem->vpll_mdiv, mem->vpll_pdiv, mem->vpll_sdiv);
+ writel(val, &clk->vpll_con0);
+ while (readl(&clk->vpll_con0) & VPLL_CON0_LOCKED)
+ ;
+
+ writel(CLK_SRC_CORE0_VAL, &clk->src_core0);
+ writel(CLK_DIV_CORE0_VAL, &clk->div_core0);
+ while (readl(&clk->div_stat_core0) != 0)
+ ;
+
+ writel(CLK_DIV_CORE1_VAL, &clk->div_core1);
+ while (readl(&clk->div_stat_core1) != 0)
+ ;
+
+ writel(CLK_DIV_SYSRGT_VAL, &clk->div_sysrgt);
+ while (readl(&clk->div_stat_sysrgt) != 0)
+ ;
+
+ writel(CLK_DIV_ACP_VAL, &clk->div_acp);
+ while (readl(&clk->div_stat_acp) != 0)
+ ;
+
+ writel(CLK_DIV_SYSLFT_VAL, &clk->div_syslft);
+ while (readl(&clk->div_stat_syslft) != 0)
+ ;
+
+ writel(CLK_SRC_TOP0_VAL, &clk->src_top0);
+ writel(CLK_SRC_TOP1_VAL, &clk->src_top1);
+ writel(TOP2_VAL, &clk->src_top2);
+ writel(CLK_SRC_TOP3_VAL, &clk->src_top3);
+
+ writel(CLK_DIV_TOP0_VAL, &clk->div_top0);
+ while (readl(&clk->div_stat_top0))
+ ;
+
+ writel(CLK_DIV_TOP1_VAL, &clk->div_top1);
+ while (readl(&clk->div_stat_top1))
+ ;
+
+ writel(CLK_SRC_LEX_VAL, &clk->src_lex);
+ while (1) {
+ val = readl(&clk->mux_stat_lex);
+ if (val == (val | 1))
+ break;
+ }
+
+ writel(CLK_DIV_LEX_VAL, &clk->div_lex);
+ while (readl(&clk->div_stat_lex))
+ ;
+
+ writel(CLK_DIV_R0X_VAL, &clk->div_r0x);
+ while (readl(&clk->div_stat_r0x))
+ ;
+
+ writel(CLK_DIV_R0X_VAL, &clk->div_r0x);
+ while (readl(&clk->div_stat_r0x))
+ ;
+
+ writel(CLK_DIV_R1X_VAL, &clk->div_r1x);
+ while (readl(&clk->div_stat_r1x))
+ ;
+
+ writel(CLK_REG_DISABLE, &clk->src_cdrex);
+
+ writel(CLK_DIV_CDREX_VAL, &clk->div_cdrex);
+ while (readl(&clk->div_stat_cdrex))
+ ;
+
+ val = readl(&clk->src_cpu);
+ val |= CLK_SRC_CPU_VAL;
+ writel(val, &clk->src_cpu);
+
+ val = readl(&clk->src_top2);
+ val |= CLK_SRC_TOP2_VAL;
+ writel(val, &clk->src_top2);
+
+ val = readl(&clk->src_core1);
+ val |= CLK_SRC_CORE1_VAL;
+ writel(val, &clk->src_core1);
+
+ writel(CLK_SRC_FSYS0_VAL, &clk->src_fsys);
+ writel(CLK_DIV_FSYS0_VAL, &clk->div_fsys0);
+ while (readl(&clk->div_stat_fsys0))
+ ;
+
+ writel(CLK_REG_DISABLE, &clk->clkout_cmu_cpu);
+ writel(CLK_REG_DISABLE, &clk->clkout_cmu_core);
+ writel(CLK_REG_DISABLE, &clk->clkout_cmu_acp);
+ writel(CLK_REG_DISABLE, &clk->clkout_cmu_top);
+ writel(CLK_REG_DISABLE, &clk->clkout_cmu_lex);
+ writel(CLK_REG_DISABLE, &clk->clkout_cmu_r0x);
+ writel(CLK_REG_DISABLE, &clk->clkout_cmu_r1x);
+ writel(CLK_REG_DISABLE, &clk->clkout_cmu_cdrex);
+
+ writel(CLK_SRC_PERIC0_VAL, &clk->src_peric0);
+ writel(CLK_DIV_PERIC0_VAL, &clk->div_peric0);
+
+ writel(CLK_SRC_PERIC1_VAL, &clk->src_peric1);
+ writel(CLK_DIV_PERIC1_VAL, &clk->div_peric1);
+ writel(CLK_DIV_PERIC2_VAL, &clk->div_peric2);
+ writel(CLK_DIV_PERIC3_VAL, &clk->div_peric3);
+
+ writel(SCLK_SRC_ISP_VAL, &clk->sclk_src_isp);
+ writel(SCLK_DIV_ISP_VAL, &clk->sclk_div_isp);
+ writel(CLK_DIV_ISP0_VAL, &clk->div_isp0);
+ writel(CLK_DIV_ISP1_VAL, &clk->div_isp1);
+ writel(CLK_DIV_ISP2_VAL, &clk->div_isp2);
+
+ /* FIMD1 SRC CLK SELECTION */
+ writel(CLK_SRC_DISP1_0_VAL, &clk->src_disp1_0);
+
+ val = MMC2_PRE_RATIO_VAL << MMC2_PRE_RATIO_OFFSET
+ | MMC2_RATIO_VAL << MMC2_RATIO_OFFSET
+ | MMC3_PRE_RATIO_VAL << MMC3_PRE_RATIO_OFFSET
+ | MMC3_RATIO_VAL << MMC3_RATIO_OFFSET;
+ writel(val, &clk->div_fsys2);
+}
diff --git a/board/samsung/arndale/clock_init.h b/board/samsung/arndale/clock_init.h
new file mode 100644
index 0000000..5d01a6c
--- /dev/null
+++ b/board/samsung/arndale/clock_init.h
@@ -0,0 +1,149 @@
+/*
+ * Clock initialization routines
+ *
+ * Copyright (c) 2011 The Chromium OS Authors.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __ARNDALE_CLOCK_INIT_H
+#define __ARNDALE_CLOCK_INIT_H
+
+enum {
+ MEM_TIMINGS_MSR_COUNT = 4,
+};
+
+/* These are the ratio's for configuring ARM clock */
+struct arm_clk_ratios {
+ unsigned arm_freq_mhz; /* Frequency of ARM core in MHz */
+
+ unsigned apll_mdiv;
+ unsigned apll_pdiv;
+ unsigned apll_sdiv;
+
+ unsigned arm2_ratio;
+ unsigned apll_ratio;
+ unsigned pclk_dbg_ratio;
+ unsigned atb_ratio;
+ unsigned periph_ratio;
+ unsigned acp_ratio;
+ unsigned cpud_ratio;
+ unsigned arm_ratio;
+};
+
+/* These are the memory timings for a particular memory type and speed */
+struct mem_timings {
+ enum mem_manuf mem_manuf; /* Memory manufacturer */
+ enum ddr_mode mem_type; /* Memory type */
+ unsigned frequency_mhz; /* Frequency of memory in MHz */
+
+ /* Here follow the timing parameters for the selected memory */
+ unsigned apll_mdiv;
+ unsigned apll_pdiv;
+ unsigned apll_sdiv;
+ unsigned mpll_mdiv;
+ unsigned mpll_pdiv;
+ unsigned mpll_sdiv;
+ unsigned cpll_mdiv;
+ unsigned cpll_pdiv;
+ unsigned cpll_sdiv;
+ unsigned gpll_mdiv;
+ unsigned gpll_pdiv;
+ unsigned gpll_sdiv;
+ unsigned epll_mdiv;
+ unsigned epll_pdiv;
+ unsigned epll_sdiv;
+ unsigned vpll_mdiv;
+ unsigned vpll_pdiv;
+ unsigned vpll_sdiv;
+ unsigned bpll_mdiv;
+ unsigned bpll_pdiv;
+ unsigned bpll_sdiv;
+ unsigned pclk_cdrex_ratio;
+ unsigned direct_cmd_msr[MEM_TIMINGS_MSR_COUNT];
+
+ unsigned timing_ref;
+ unsigned timing_row;
+ unsigned timing_data;
+ unsigned timing_power;
+
+ /* DQS, DQ, DEBUG offsets */
+ unsigned phy0_dqs;
+ unsigned phy1_dqs;
+ unsigned phy0_dq;
+ unsigned phy1_dq;
+ unsigned phy0_tFS;
+ unsigned phy1_tFS;
+ unsigned phy0_pulld_dqs;
+ unsigned phy1_pulld_dqs;
+
+ unsigned lpddr3_ctrl_phy_reset;
+ unsigned ctrl_start_point;
+ unsigned ctrl_inc;
+ unsigned ctrl_start;
+ unsigned ctrl_dll_on;
+ unsigned ctrl_ref;
+
+ unsigned ctrl_force;
+ unsigned ctrl_rdlat;
+ unsigned ctrl_bstlen;
+
+ unsigned fp_resync;
+ unsigned iv_size;
+ unsigned dfi_init_start;
+ unsigned aref_en;
+
+ unsigned rd_fetch;
+
+ unsigned zq_mode_dds;
+ unsigned zq_mode_term;
+ unsigned zq_mode_noterm; /* 1 to allow termination disable */
+
+ unsigned memcontrol;
+ unsigned memconfig;
+
+ unsigned membaseconfig0;
+ unsigned membaseconfig1;
+ unsigned prechconfig_tp_cnt;
+ unsigned dpwrdn_cyc;
+ unsigned dsref_cyc;
+ unsigned concontrol;
+ /* Channel and Chip Selection */
+ uint8_t dmc_channels; /* number of memory channels */
+ uint8_t chips_per_channel; /* number of chips per channel */
+ uint8_t chips_to_configure; /* number of chips to configure */
+ uint8_t send_zq_init; /* 1 to send this command */
+ unsigned impedance; /* drive strength impedeance */
+ uint8_t gate_leveling_enable; /* check gate leveling is enabled */
+};
+
+/**
+ * Get the correct memory timings for our selected memory type and speed.
+ *
+ * This function can be called from SPL or the main U-Boot.
+ *
+ * @return pointer to the memory timings that we should use
+ */
+struct mem_timings *clock_get_mem_timings(void);
+
+/*
+ * Initialize clock for the device
+ */
+void system_clock_init(void);
+#endif
diff --git a/board/samsung/arndale/dmc_common.c b/board/samsung/arndale/dmc_common.c
new file mode 100644
index 0000000..5a51def
--- /dev/null
+++ b/board/samsung/arndale/dmc_common.c
@@ -0,0 +1,199 @@
+/*
+ * Mem setup common file for different types of DDR present on Arndale boards.
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/spl.h>
+
+#include "clock_init.h"
+#include "setup.h"
+
+#define ZQ_INIT_TIMEOUT 10000
+
+int dmc_config_zq(struct mem_timings *mem,
+ struct exynos5_phy_control *phy0_ctrl,
+ struct exynos5_phy_control *phy1_ctrl)
+{
+ unsigned long val = 0;
+ int i;
+
+ /*
+ * ZQ Calibration:
+ * Select Driver Strength,
+ * long calibration for manual calibration
+ */
+ val = PHY_CON16_RESET_VAL;
+ val |= mem->zq_mode_dds << PHY_CON16_ZQ_MODE_DDS_SHIFT;
+ val |= mem->zq_mode_term << PHY_CON16_ZQ_MODE_TERM_SHIFT;
+ val |= ZQ_CLK_DIV_EN;
+ writel(val, &phy0_ctrl->phy_con16);
+ writel(val, &phy1_ctrl->phy_con16);
+
+ /* Disable termination */
+ if (mem->zq_mode_noterm)
+ val |= PHY_CON16_ZQ_MODE_NOTERM_MASK;
+ writel(val, &phy0_ctrl->phy_con16);
+ writel(val, &phy1_ctrl->phy_con16);
+
+ /* ZQ_MANUAL_START: Enable */
+ val |= ZQ_MANUAL_STR;
+ writel(val, &phy0_ctrl->phy_con16);
+ writel(val, &phy1_ctrl->phy_con16);
+
+ /* ZQ_MANUAL_START: Disable */
+ val &= ~ZQ_MANUAL_STR;
+
+ /*
+ * Since we are manaully calibrating the ZQ values,
+ * we are looping for the ZQ_init to complete.
+ */
+ i = ZQ_INIT_TIMEOUT;
+ while ((readl(&phy0_ctrl->phy_con17) & ZQ_DONE) != ZQ_DONE && i > 0) {
+ sdelay(100);
+ i--;
+ }
+ if (!i)
+ return -1;
+ writel(val, &phy0_ctrl->phy_con16);
+
+ i = ZQ_INIT_TIMEOUT;
+ while ((readl(&phy1_ctrl->phy_con17) & ZQ_DONE) != ZQ_DONE && i > 0) {
+ sdelay(100);
+ i--;
+ }
+ if (!i)
+ return -1;
+ writel(val, &phy1_ctrl->phy_con16);
+
+ return 0;
+}
+
+void update_reset_dll(struct exynos5_dmc *dmc, enum ddr_mode mode)
+{
+ unsigned long val;
+
+ if (mode == DDR_MODE_DDR3) {
+ val = MEM_TERM_EN | PHY_TERM_EN | DMC_CTRL_SHGATE;
+ writel(val, &dmc->phycontrol0);
+ }
+
+ /* Update DLL Information: Force DLL Resyncronization */
+ val = readl(&dmc->phycontrol0);
+ val |= FP_RSYNC;
+ writel(val, &dmc->phycontrol0);
+
+ /* Reset Force DLL Resyncronization */
+ val = readl(&dmc->phycontrol0);
+ val &= ~FP_RSYNC;
+ writel(val, &dmc->phycontrol0);
+}
+
+void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc)
+{
+ int channel, chip;
+
+ for (channel = 0; channel < mem->dmc_channels; channel++) {
+ unsigned long mask;
+
+ mask = channel << DIRECT_CMD_CHANNEL_SHIFT;
+ for (chip = 0; chip < mem->chips_to_configure; chip++) {
+ int i;
+
+ mask |= chip << DIRECT_CMD_CHIP_SHIFT;
+
+ /* Sending NOP command */
+ writel(DIRECT_CMD_NOP | mask, &dmc->directcmd);
+
+ /*
+ * TODO(alim.akhtar at samsung.com): Do we need these
+ * delays? This one and the next were not there for
+ * DDR3.
+ */
+ sdelay(0x10000);
+
+ /* Sending EMRS/MRS commands */
+ for (i = 0; i < MEM_TIMINGS_MSR_COUNT; i++) {
+ writel(mem->direct_cmd_msr[i] | mask,
+ &dmc->directcmd);
+ sdelay(0x10000);
+ }
+
+ if (mem->send_zq_init) {
+ /* Sending ZQINIT command */
+ writel(DIRECT_CMD_ZQINIT | mask,
+ &dmc->directcmd);
+
+ sdelay(10000);
+ }
+ }
+ }
+}
+
+void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc)
+{
+ int channel, chip;
+
+ for (channel = 0; channel < mem->dmc_channels; channel++) {
+ unsigned long mask;
+
+ mask = channel << DIRECT_CMD_CHANNEL_SHIFT;
+ for (chip = 0; chip < mem->chips_per_channel; chip++) {
+ mask |= chip << DIRECT_CMD_CHIP_SHIFT;
+
+ /* PALL (all banks precharge) CMD */
+ writel(DIRECT_CMD_PALL | mask, &dmc->directcmd);
+ sdelay(0x10000);
+ }
+ }
+}
+
+void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc)
+{
+ writel(mem->memconfig, &dmc->memconfig0);
+ writel(mem->memconfig, &dmc->memconfig1);
+ writel(DMC_MEMBASECONFIG0_VAL, &dmc->membaseconfig0);
+ writel(DMC_MEMBASECONFIG1_VAL, &dmc->membaseconfig1);
+}
+
+void mem_ctrl_init()
+{
+ struct spl_machine_param *param = spl_get_machine_params();
+ struct mem_timings *mem;
+ int ret;
+
+ mem = clock_get_mem_timings();
+
+ /* If there are any other memory variant, add their init call below */
+ if (param->mem_type == DDR_MODE_DDR3) {
+ ret = ddr3_mem_ctrl_init(mem, param->mem_iv_size);
+ if (ret) {
+ /* will hang if failed to init memory control */
+ while (1)
+ ;
+ }
+ } else {
+ /* will hang if unknow memory type */
+ while (1)
+ ;
+ }
+}
diff --git a/board/samsung/arndale/dmc_init_ddr3.c b/board/samsung/arndale/dmc_init_ddr3.c
new file mode 100644
index 0000000..ce91451
--- /dev/null
+++ b/board/samsung/arndale/dmc_init_ddr3.c
@@ -0,0 +1,228 @@
+/*
+ * DDR3 mem setup file for Arndale board based on EXYNOS5
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/dmc.h>
+#include "setup.h"
+#include "clock_init.h"
+
+#define RDLVL_COMPLETE_TIMEOUT 10000
+
+static void reset_phy_ctrl(void)
+{
+ struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
+
+ writel(DDR3PHY_CTRL_PHY_RESET_OFF, &clk->lpddr3phy_ctrl);
+ writel(DDR3PHY_CTRL_PHY_RESET, &clk->lpddr3phy_ctrl);
+}
+
+int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size)
+{
+ unsigned int val;
+ struct exynos5_phy_control *phy0_ctrl, *phy1_ctrl;
+ struct exynos5_dmc *dmc;
+ int i;
+
+ phy0_ctrl = (struct exynos5_phy_control *)EXYNOS5_DMC_PHY0_BASE;
+ phy1_ctrl = (struct exynos5_phy_control *)EXYNOS5_DMC_PHY1_BASE;
+ dmc = (struct exynos5_dmc *)EXYNOS5_DMC_CTRL_BASE;
+
+ reset_phy_ctrl();
+
+ /* Set Impedance Output Driver */
+ val = (mem->impedance << CA_CK_DRVR_DS_OFFSET) |
+ (mem->impedance << CA_CKE_DRVR_DS_OFFSET) |
+ (mem->impedance << CA_CS_DRVR_DS_OFFSET) |
+ (mem->impedance << CA_ADR_DRVR_DS_OFFSET);
+ writel(val, &phy0_ctrl->phy_con39);
+ writel(val, &phy1_ctrl->phy_con39);
+
+ /* Set Read Latency and Burst Length for PHY0 and PHY1 */
+ val = (mem->ctrl_bstlen << PHY_CON42_CTRL_BSTLEN_SHIFT) |
+ (mem->ctrl_rdlat << PHY_CON42_CTRL_RDLAT_SHIFT);
+ writel(val, &phy0_ctrl->phy_con42);
+ writel(val, &phy1_ctrl->phy_con42);
+
+ /* ZQ Calibration */
+ if (dmc_config_zq(mem, phy0_ctrl, phy1_ctrl))
+ return SETUP_ERR_ZQ_CALIBRATION_FAILURE;
+
+ /* DQ Signal */
+ writel(mem->phy0_pulld_dqs, &phy0_ctrl->phy_con14);
+ writel(mem->phy1_pulld_dqs, &phy1_ctrl->phy_con14);
+
+ writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)
+ | (mem->dfi_init_start << CONCONTROL_DFI_INIT_START_SHIFT),
+ &dmc->concontrol);
+
+ update_reset_dll(dmc, DDR_MODE_DDR3);
+
+ /* DQS Signal */
+ writel(mem->phy0_dqs, &phy0_ctrl->phy_con4);
+ writel(mem->phy1_dqs, &phy1_ctrl->phy_con4);
+
+ writel(mem->phy0_dq, &phy0_ctrl->phy_con6);
+ writel(mem->phy1_dq, &phy1_ctrl->phy_con6);
+
+ writel(mem->phy0_tFS, &phy0_ctrl->phy_con10);
+ writel(mem->phy1_tFS, &phy1_ctrl->phy_con10);
+
+ val = (mem->ctrl_start_point << PHY_CON12_CTRL_START_POINT_SHIFT) |
+ (mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
+ (mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
+ (mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
+ writel(val, &phy0_ctrl->phy_con12);
+ writel(val, &phy1_ctrl->phy_con12);
+
+ /* Start DLL locking */
+ writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
+ &phy0_ctrl->phy_con12);
+ writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
+ &phy1_ctrl->phy_con12);
+
+ update_reset_dll(dmc, DDR_MODE_DDR3);
+
+ writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT),
+ &dmc->concontrol);
+
+ /* Memory Channel Inteleaving Size */
+ writel(mem->iv_size, &dmc->ivcontrol);
+
+ writel(mem->memconfig, &dmc->memconfig0);
+ writel(mem->memconfig, &dmc->memconfig1);
+ writel(mem->membaseconfig0, &dmc->membaseconfig0);
+ writel(mem->membaseconfig1, &dmc->membaseconfig1);
+
+ /* Precharge Configuration */
+ writel(mem->prechconfig_tp_cnt << PRECHCONFIG_TP_CNT_SHIFT,
+ &dmc->prechconfig);
+
+ /* Power Down mode Configuration */
+ writel(mem->dpwrdn_cyc << PWRDNCONFIG_DPWRDN_CYC_SHIFT |
+ mem->dsref_cyc << PWRDNCONFIG_DSREF_CYC_SHIFT,
+ &dmc->pwrdnconfig);
+
+ /* TimingRow, TimingData, TimingPower and Timingaref
+ * values as per Memory AC parameters
+ */
+ writel(mem->timing_ref, &dmc->timingref);
+ writel(mem->timing_row, &dmc->timingrow);
+ writel(mem->timing_data, &dmc->timingdata);
+ writel(mem->timing_power, &dmc->timingpower);
+
+ /* Send PALL command */
+ dmc_config_prech(mem, dmc);
+
+ /* Send NOP, MRS and ZQINIT commands */
+ dmc_config_mrs(mem, dmc);
+
+ if (mem->gate_leveling_enable) {
+ val = PHY_CON0_RESET_VAL;
+ val |= P0_CMD_EN;
+ writel(val, &phy0_ctrl->phy_con0);
+ writel(val, &phy1_ctrl->phy_con0);
+
+ val = PHY_CON2_RESET_VAL;
+ val |= INIT_DESKEW_EN;
+ writel(val, &phy0_ctrl->phy_con2);
+ writel(val, &phy1_ctrl->phy_con2);
+
+ val = PHY_CON0_RESET_VAL;
+ val |= P0_CMD_EN;
+ val |= BYTE_RDLVL_EN;
+ writel(val, &phy0_ctrl->phy_con0);
+ writel(val, &phy1_ctrl->phy_con0);
+
+ val = (mem->ctrl_start_point <<
+ PHY_CON12_CTRL_START_POINT_SHIFT) |
+ (mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
+ (mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
+ (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
+ (mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
+ writel(val, &phy0_ctrl->phy_con12);
+ writel(val, &phy1_ctrl->phy_con12);
+
+ val = PHY_CON2_RESET_VAL;
+ val |= INIT_DESKEW_EN;
+ val |= RDLVL_GATE_EN;
+ writel(val, &phy0_ctrl->phy_con2);
+ writel(val, &phy1_ctrl->phy_con2);
+
+ val = PHY_CON0_RESET_VAL;
+ val |= P0_CMD_EN;
+ val |= BYTE_RDLVL_EN;
+ val |= CTRL_SHGATE;
+ writel(val, &phy0_ctrl->phy_con0);
+ writel(val, &phy1_ctrl->phy_con0);
+
+ val = PHY_CON1_RESET_VAL;
+ val &= ~(CTRL_GATEDURADJ_MASK);
+ writel(val, &phy0_ctrl->phy_con1);
+ writel(val, &phy1_ctrl->phy_con1);
+
+ writel(CTRL_RDLVL_GATE_ENABLE, &dmc->rdlvl_config);
+ i = RDLVL_COMPLETE_TIMEOUT;
+ while ((readl(&dmc->phystatus) &
+ (RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1)) !=
+ (RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1) && i > 0) {
+ /*
+ * TODO(waihong): Comment on how long this take to
+ * timeout
+ */
+ sdelay(100);
+ i--;
+ }
+ if (!i)
+ return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
+ writel(CTRL_RDLVL_GATE_DISABLE, &dmc->rdlvl_config);
+
+ writel(0, &phy0_ctrl->phy_con14);
+ writel(0, &phy1_ctrl->phy_con14);
+
+ val = (mem->ctrl_start_point <<
+ PHY_CON12_CTRL_START_POINT_SHIFT) |
+ (mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
+ (mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
+ (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
+ (mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
+ (mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
+ writel(val, &phy0_ctrl->phy_con12);
+ writel(val, &phy1_ctrl->phy_con12);
+
+ update_reset_dll(dmc, DDR_MODE_DDR3);
+ }
+
+ /* Send PALL command */
+ dmc_config_prech(mem, dmc);
+
+ writel(mem->memcontrol, &dmc->memcontrol);
+
+ /* Set DMC Concontrol and enable auto-refresh counter */
+ writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)
+ | (mem->aref_en << CONCONTROL_AREF_EN_SHIFT), &dmc->concontrol);
+ return 0;
+}
diff --git a/board/samsung/arndale/lowlevel_init.S b/board/samsung/arndale/lowlevel_init.S
new file mode 100644
index 0000000..4fa73a7
--- /dev/null
+++ b/board/samsung/arndale/lowlevel_init.S
@@ -0,0 +1,92 @@
+/*
+ * Lowlevel setup for Arndale board based on Exynos5
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/cpu.h>
+
+_TEXT_BASE:
+ .word CONFIG_SYS_TEXT_BASE
+
+ .globl lowlevel_init
+lowlevel_init:
+
+ /* use iRAM stack in bl2 */
+ ldr sp, =CONFIG_IRAM_STACK
+ stmdb r13!, {ip,lr}
+
+ /* check reset status */
+ ldr r0, =(EXYNOS5_POWER_BASE + INFORM1_OFFSET)
+ ldr r1, [r0]
+
+ /* AFTR wakeup reset */
+ ldr r2, =S5P_CHECK_DIDLE
+ cmp r1, r2
+ beq exit_wakeup
+
+ /* Sleep wakeup reset */
+ ldr r2, =S5P_CHECK_SLEEP
+ cmp r1, r2
+ beq wakeup_reset
+
+ /*
+ * If U-boot is already running in RAM, no need to relocate U-Boot.
+ * Memory controller must be configured before relocating U-Boot
+ * in ram.
+ */
+ ldr r0, =0x0ffffff /* r0 <- Mask Bits*/
+ bic r1, pc, r0 /* pc <- current addr of code */
+ /* r1 <- unmasked bits of pc */
+ ldr r2, _TEXT_BASE /* r2 <- original base addr in ram */
+ bic r2, r2, r0 /* r2 <- unmasked bits of r2*/
+ cmp r1, r2 /* compare r1, r2 */
+ beq 1f /* r0 == r1 then skip sdram init */
+
+ /* init system clock */
+ bl system_clock_init
+
+ /* Memory initialize */
+ bl mem_ctrl_init
+1:
+ bl arch_cpu_init
+ bl tzpc_init
+ ldmia r13!, {ip,pc}
+
+wakeup_reset:
+ bl system_clock_init
+ bl mem_ctrl_init
+ bl arch_cpu_init
+ bl tzpc_init
+
+exit_wakeup:
+ /* Load return address and jump to kernel */
+ ldr r0, =(EXYNOS5_POWER_BASE + INFORM0_OFFSET)
+
+ /* r1 = physical address of exynos5_cpu_resume function*/
+ ldr r1, [r0]
+
+ /* Jump to kernel */
+ mov pc, r1
+ nop
+ nop
diff --git a/board/samsung/arndale/mmc_boot.c b/board/samsung/arndale/mmc_boot.c
new file mode 100644
index 0000000..72219a0
--- /dev/null
+++ b/board/samsung/arndale/mmc_boot.c
@@ -0,0 +1,58 @@
+/*
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include<common.h>
+#include<config.h>
+
+/*
+* Copy U-boot from mmc to RAM:
+* COPY_BL2_FNPTR_ADDR: Address in iRAM, which Contains
+* Pointer to API (Data transfer from mmc to ram)
+*/
+void copy_uboot_to_ram(void)
+{
+ u32 (*copy_bl2)(u32, u32, u32) = (void *) *(u32 *)COPY_BL2_FNPTR_ADDR;
+
+ copy_bl2(BL2_START_OFFSET, BL2_SIZE_BLOC_COUNT, CONFIG_SYS_TEXT_BASE);
+}
+
+void board_init_f(unsigned long bootflag)
+{
+ __attribute__((noreturn)) void (*uboot)(void);
+ copy_uboot_to_ram();
+
+ /* Jump to U-Boot image */
+ uboot = (void *)CONFIG_SYS_TEXT_BASE;
+ (*uboot)();
+ /* Never returns Here */
+}
+
+/* Place Holders */
+void board_init_r(gd_t *id, ulong dest_addr)
+{
+ /* Function attribute is no-return */
+ /* This Function never executes */
+ while (1)
+ ;
+}
+
+void save_boot_params(u32 r0, u32 r1, u32 r2, u32 r3) {}
diff --git a/board/samsung/arndale/setup.h b/board/samsung/arndale/setup.h
new file mode 100644
index 0000000..622b148
--- /dev/null
+++ b/board/samsung/arndale/setup.h
@@ -0,0 +1,569 @@
+/*
+ * Machine Specific Values for Arndale board based on EXYNOS5
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _ARNDALE_SETUP_H
+#define _ARNDALE_SETUP_H
+
+#include <config.h>
+#include <asm/arch/dmc.h>
+
+/* APLL_CON1 */
+#define APLL_CON1_VAL (0x00203800)
+
+/* MPLL_CON1 */
+#define MPLL_CON1_VAL (0x00203800)
+
+/* CPLL_CON1 */
+#define CPLL_CON1_VAL (0x00203800)
+
+/* GPLL_CON1 */
+#define GPLL_CON1_VAL (0x00203800)
+
+/* EPLL_CON1, CON2 */
+#define EPLL_CON1_VAL 0x00000000
+#define EPLL_CON2_VAL 0x00000080
+
+/* VPLL_CON1, CON2 */
+#define VPLL_CON1_VAL 0x00000000
+#define VPLL_CON2_VAL 0x00000080
+
+/* BPLL_CON1 */
+#define BPLL_CON1_VAL 0x00203800
+
+/* Set PLL */
+#define set_pll(mdiv, pdiv, sdiv) (1<<31 | mdiv<<16 | pdiv<<8 | sdiv)
+
+/* CLK_SRC_CPU */
+/* 0 = MOUTAPLL, 1 = SCLKMPLL */
+#define MUX_HPM_SEL 0
+#define MUX_CPU_SEL 0
+#define MUX_APLL_SEL 1
+
+#define CLK_SRC_CPU_VAL ((MUX_HPM_SEL << 20) \
+ | (MUX_CPU_SEL << 16) \
+ | (MUX_APLL_SEL))
+
+/* MEMCONTROL register bit fields */
+#define DMC_MEMCONTROL_CLK_STOP_DISABLE (0 << 0)
+#define DMC_MEMCONTROL_DPWRDN_DISABLE (0 << 1)
+#define DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE (0 << 2)
+#define DMC_MEMCONTROL_TP_DISABLE (0 << 4)
+#define DMC_MEMCONTROL_DSREF_DISABLE (0 << 5)
+#define DMC_MEMCONTROL_DSREF_ENABLE (1 << 5)
+#define DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(x) (x << 6)
+
+#define DMC_MEMCONTROL_MEM_TYPE_LPDDR3 (7 << 8)
+#define DMC_MEMCONTROL_MEM_TYPE_DDR3 (6 << 8)
+#define DMC_MEMCONTROL_MEM_TYPE_LPDDR2 (5 << 8)
+
+#define DMC_MEMCONTROL_MEM_WIDTH_32BIT (2 << 12)
+
+#define DMC_MEMCONTROL_NUM_CHIP_1 (0 << 16)
+#define DMC_MEMCONTROL_NUM_CHIP_2 (1 << 16)
+
+#define DMC_MEMCONTROL_BL_8 (3 << 20)
+#define DMC_MEMCONTROL_BL_4 (2 << 20)
+
+#define DMC_MEMCONTROL_PZQ_DISABLE (0 << 24)
+
+#define DMC_MEMCONTROL_MRR_BYTE_7_0 (0 << 25)
+#define DMC_MEMCONTROL_MRR_BYTE_15_8 (1 << 25)
+#define DMC_MEMCONTROL_MRR_BYTE_23_16 (2 << 25)
+#define DMC_MEMCONTROL_MRR_BYTE_31_24 (3 << 25)
+
+/* MEMCONFIG0 register bit fields */
+#define DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED (1 << 12)
+#define DMC_MEMCONFIGx_CHIP_COL_10 (3 << 8)
+#define DMC_MEMCONFIGx_CHIP_ROW_14 (2 << 4)
+#define DMC_MEMCONFIGx_CHIP_ROW_15 (3 << 4)
+#define DMC_MEMCONFIGx_CHIP_BANK_8 (3 << 0)
+
+#define DMC_MEMBASECONFIGx_CHIP_BASE(x) (x << 16)
+#define DMC_MEMBASECONFIGx_CHIP_MASK(x) (x << 0)
+#define DMC_MEMBASECONFIG_VAL(x) ( \
+ DMC_MEMBASECONFIGx_CHIP_BASE(x) | \
+ DMC_MEMBASECONFIGx_CHIP_MASK(0x780) \
+)
+
+#define DMC_MEMBASECONFIG0_VAL DMC_MEMBASECONFIG_VAL(0x40)
+#define DMC_MEMBASECONFIG1_VAL DMC_MEMBASECONFIG_VAL(0x80)
+
+#define DMC_PRECHCONFIG_VAL 0xFF000000
+#define DMC_PWRDNCONFIG_VAL 0xFFFF00FF
+
+#define DMC_CONCONTROL_RESET_VAL 0x0FFF0000
+#define DFI_INIT_START (1 << 28)
+#define EMPTY (1 << 8)
+#define AREF_EN (1 << 5)
+
+#define DFI_INIT_COMPLETE_CHO (1 << 2)
+#define DFI_INIT_COMPLETE_CH1 (1 << 3)
+
+#define RDLVL_COMPLETE_CHO (1 << 14)
+#define RDLVL_COMPLETE_CH1 (1 << 15)
+
+#define CLK_STOP_EN (1 << 0)
+#define DPWRDN_EN (1 << 1)
+#define DSREF_EN (1 << 5)
+
+/* COJCONTROL register bit fields */
+#define DMC_CONCONTROL_IO_PD_CON_DISABLE (0 << 3)
+#define DMC_CONCONTROL_AREF_EN_DISABLE (0 << 5)
+#define DMC_CONCONTROL_EMPTY_DISABLE (0 << 8)
+#define DMC_CONCONTROL_EMPTY_ENABLE (1 << 8)
+#define DMC_CONCONTROL_RD_FETCH_DISABLE (0x0 << 12)
+#define DMC_CONCONTROL_TIMEOUT_LEVEL0 (0xFFF << 16)
+#define DMC_CONCONTROL_DFI_INIT_START_DISABLE (0 << 28)
+
+/* CLK_DIV_CPU0_VAL */
+#define CLK_DIV_CPU0_VAL ((ARM2_RATIO << 28) \
+ | (APLL_RATIO << 24) \
+ | (PCLK_DBG_RATIO << 20) \
+ | (ATB_RATIO << 16) \
+ | (PERIPH_RATIO << 12) \
+ | (ACP_RATIO << 8) \
+ | (CPUD_RATIO << 4) \
+ | (ARM_RATIO))
+
+
+/* CLK_FSYS */
+#define CLK_SRC_FSYS0_VAL 0x66666
+#define CLK_DIV_FSYS0_VAL 0x0BB00000
+
+/* CLK_DIV_CPU1 */
+#define HPM_RATIO 0x2
+#define COPY_RATIO 0x0
+
+/* CLK_DIV_CPU1 = 0x00000003 */
+#define CLK_DIV_CPU1_VAL ((HPM_RATIO << 4) \
+ | (COPY_RATIO))
+
+/* CLK_SRC_CORE0 */
+#define CLK_SRC_CORE0_VAL 0x00000000
+
+/* CLK_SRC_CORE1 */
+#define CLK_SRC_CORE1_VAL 0x100
+
+/* CLK_DIV_CORE0 */
+#define CLK_DIV_CORE0_VAL 0x00120000
+
+/* CLK_DIV_CORE1 */
+#define CLK_DIV_CORE1_VAL 0x07070700
+
+/* CLK_DIV_SYSRGT */
+#define CLK_DIV_SYSRGT_VAL 0x00000111
+
+/* CLK_DIV_ACP */
+#define CLK_DIV_ACP_VAL 0x12
+
+/* CLK_DIV_SYSLFT */
+#define CLK_DIV_SYSLFT_VAL 0x00000311
+
+/* CLK_SRC_CDREX */
+#define CLK_SRC_CDREX_VAL 0x1
+
+/* CLK_DIV_CDREX */
+#define MCLK_CDREX2_RATIO 0x0
+#define ACLK_EFCON_RATIO 0x1
+#define MCLK_DPHY_RATIO 0x1
+#define MCLK_CDREX_RATIO 0x1
+#define ACLK_C2C_200_RATIO 0x1
+#define C2C_CLK_400_RATIO 0x1
+#define PCLK_CDREX_RATIO 0x1
+#define ACLK_CDREX_RATIO 0x1
+
+#define CLK_DIV_CDREX_VAL ((MCLK_DPHY_RATIO << 24) \
+ | (C2C_CLK_400_RATIO << 6) \
+ | (PCLK_CDREX_RATIO << 4) \
+ | (ACLK_CDREX_RATIO))
+
+/* CLK_SRC_TOP0 */
+#define MUX_ACLK_300_GSCL_SEL 0x0
+#define MUX_ACLK_300_GSCL_MID_SEL 0x0
+#define MUX_ACLK_400_G3D_MID_SEL 0x0
+#define MUX_ACLK_333_SEL 0x0
+#define MUX_ACLK_300_DISP1_SEL 0x0
+#define MUX_ACLK_300_DISP1_MID_SEL 0x0
+#define MUX_ACLK_200_SEL 0x0
+#define MUX_ACLK_166_SEL 0x0
+#define CLK_SRC_TOP0_VAL ((MUX_ACLK_300_GSCL_SEL << 25) \
+ | (MUX_ACLK_300_GSCL_MID_SEL << 24) \
+ | (MUX_ACLK_400_G3D_MID_SEL << 20) \
+ | (MUX_ACLK_333_SEL << 16) \
+ | (MUX_ACLK_300_DISP1_SEL << 15) \
+ | (MUX_ACLK_300_DISP1_MID_SEL << 14) \
+ | (MUX_ACLK_200_SEL << 12) \
+ | (MUX_ACLK_166_SEL << 8))
+
+/* CLK_SRC_TOP1 */
+#define MUX_ACLK_400_G3D_SEL 0x1
+#define MUX_ACLK_400_ISP_SEL 0x0
+#define MUX_ACLK_400_IOP_SEL 0x0
+#define MUX_ACLK_MIPI_HSI_TXBASE_SEL 0x0
+#define MUX_ACLK_300_GSCL_MID1_SEL 0x0
+#define MUX_ACLK_300_DISP1_MID1_SEL 0x0
+#define CLK_SRC_TOP1_VAL ((MUX_ACLK_400_G3D_SEL << 28) \
+ |(MUX_ACLK_400_ISP_SEL << 24) \
+ |(MUX_ACLK_400_IOP_SEL << 20) \
+ |(MUX_ACLK_MIPI_HSI_TXBASE_SEL << 16) \
+ |(MUX_ACLK_300_GSCL_MID1_SEL << 12) \
+ |(MUX_ACLK_300_DISP1_MID1_SEL << 8))
+
+/* CLK_SRC_TOP2 */
+#define MUX_GPLL_SEL 0x1
+#define MUX_BPLL_USER_SEL 0x0
+#define MUX_MPLL_USER_SEL 0x0
+#define MUX_VPLL_SEL 0x1
+#define MUX_EPLL_SEL 0x1
+#define MUX_CPLL_SEL 0x1
+#define VPLLSRC_SEL 0x0
+#define CLK_SRC_TOP2_VAL ((MUX_GPLL_SEL << 28) \
+ | (MUX_BPLL_USER_SEL << 24) \
+ | (MUX_MPLL_USER_SEL << 20) \
+ | (MUX_VPLL_SEL << 16) \
+ | (MUX_EPLL_SEL << 12) \
+ | (MUX_CPLL_SEL << 8) \
+ | (VPLLSRC_SEL))
+/* CLK_SRC_TOP3 */
+#define MUX_ACLK_333_SUB_SEL 0x1
+#define MUX_ACLK_400_SUB_SEL 0x1
+#define MUX_ACLK_266_ISP_SUB_SEL 0x1
+#define MUX_ACLK_266_GPS_SUB_SEL 0x0
+#define MUX_ACLK_300_GSCL_SUB_SEL 0x1
+#define MUX_ACLK_266_GSCL_SUB_SEL 0x1
+#define MUX_ACLK_300_DISP1_SUB_SEL 0x1
+#define MUX_ACLK_200_DISP1_SUB_SEL 0x1
+#define CLK_SRC_TOP3_VAL ((MUX_ACLK_333_SUB_SEL << 24) \
+ | (MUX_ACLK_400_SUB_SEL << 20) \
+ | (MUX_ACLK_266_ISP_SUB_SEL << 16) \
+ | (MUX_ACLK_266_GPS_SUB_SEL << 12) \
+ | (MUX_ACLK_300_GSCL_SUB_SEL << 10) \
+ | (MUX_ACLK_266_GSCL_SUB_SEL << 8) \
+ | (MUX_ACLK_300_DISP1_SUB_SEL << 6) \
+ | (MUX_ACLK_200_DISP1_SUB_SEL << 4))
+
+/* CLK_DIV_TOP0 */
+#define ACLK_300_DISP1_RATIO 0x2
+#define ACLK_400_G3D_RATIO 0x0
+#define ACLK_333_RATIO 0x0
+#define ACLK_266_RATIO 0x2
+#define ACLK_200_RATIO 0x3
+#define ACLK_166_RATIO 0x1
+#define ACLK_133_RATIO 0x1
+#define ACLK_66_RATIO 0x5
+
+#define CLK_DIV_TOP0_VAL ((ACLK_300_DISP1_RATIO << 28) \
+ | (ACLK_400_G3D_RATIO << 24) \
+ | (ACLK_333_RATIO << 20) \
+ | (ACLK_266_RATIO << 16) \
+ | (ACLK_200_RATIO << 12) \
+ | (ACLK_166_RATIO << 8) \
+ | (ACLK_133_RATIO << 4) \
+ | (ACLK_66_RATIO))
+
+/* CLK_DIV_TOP1 */
+#define ACLK_MIPI_HSI_TX_BASE_RATIO 0x3
+#define ACLK_66_PRE_RATIO 0x1
+#define ACLK_400_ISP_RATIO 0x1
+#define ACLK_400_IOP_RATIO 0x1
+#define ACLK_300_GSCL_RATIO 0x2
+
+#define CLK_DIV_TOP1_VAL ((ACLK_MIPI_HSI_TX_BASE_RATIO << 28) \
+ | (ACLK_66_PRE_RATIO << 24) \
+ | (ACLK_400_ISP_RATIO << 20) \
+ | (ACLK_400_IOP_RATIO << 16) \
+ | (ACLK_300_GSCL_RATIO << 12))
+
+/* APLL_LOCK */
+#define APLL_LOCK_VAL (0x546)
+/* MPLL_LOCK */
+#define MPLL_LOCK_VAL (0x546)
+/* CPLL_LOCK */
+#define CPLL_LOCK_VAL (0x546)
+/* GPLL_LOCK */
+#define GPLL_LOCK_VAL (0x546)
+/* EPLL_LOCK */
+#define EPLL_LOCK_VAL (0x3A98)
+/* VPLL_LOCK */
+#define VPLL_LOCK_VAL (0x3A98)
+/* BPLL_LOCK */
+#define BPLL_LOCK_VAL (0x546)
+
+#define MUX_APLL_SEL_MASK (1 << 0)
+#define MUX_MPLL_SEL_MASK (1 << 8)
+#define MPLL_SEL_MOUT_MPLLFOUT (2 << 8)
+#define MUX_CPLL_SEL_MASK (1 << 8)
+#define MUX_EPLL_SEL_MASK (1 << 12)
+#define MUX_VPLL_SEL_MASK (1 << 16)
+#define MUX_GPLL_SEL_MASK (1 << 28)
+#define MUX_BPLL_SEL_MASK (1 << 0)
+#define MUX_HPM_SEL_MASK (1 << 20)
+#define HPM_SEL_SCLK_MPLL (1 << 21)
+#define APLL_CON0_LOCKED (1 << 29)
+#define MPLL_CON0_LOCKED (1 << 29)
+#define BPLL_CON0_LOCKED (1 << 29)
+#define CPLL_CON0_LOCKED (1 << 29)
+#define EPLL_CON0_LOCKED (1 << 29)
+#define GPLL_CON0_LOCKED (1 << 29)
+#define VPLL_CON0_LOCKED (1 << 29)
+#define CLK_REG_DISABLE 0x0
+#define TOP2_VAL 0x0110000
+
+/* CLK_SRC_PERIC0 */
+#define PWM_SEL 0
+#define UART3_SEL 6
+#define UART2_SEL 6
+#define UART1_SEL 6
+#define UART0_SEL 6
+/* SRC_CLOCK = SCLK_MPLL */
+#define CLK_SRC_PERIC0_VAL ((PWM_SEL << 24) \
+ | (UART3_SEL << 12) \
+ | (UART2_SEL << 8) \
+ | (UART1_SEL << 4) \
+ | (UART0_SEL))
+
+/* CLK_SRC_PERIC1 */
+/* SRC_CLOCK = SCLK_MPLL */
+#define SPI0_SEL 6
+#define SPI1_SEL 6
+#define SPI2_SEL 6
+#define CLK_SRC_PERIC1_VAL ((SPI2_SEL << 24) \
+ | (SPI1_SEL << 20) \
+ | (SPI0_SEL << 16))
+
+/* SCLK_SRC_ISP - set SPI0/1 to 6 = SCLK_MPLL_USER */
+#define SPI0_ISP_SEL 6
+#define SPI1_ISP_SEL 6
+#define SCLK_SRC_ISP_VAL ((SPI1_ISP_SEL << 4) \
+ | (SPI0_ISP_SEL << 0))
+
+/* SCLK_DIV_ISP - set SPI0/1 to 0xf = divide by 16 */
+#define SPI0_ISP_RATIO 0xf
+#define SPI1_ISP_RATIO 0xf
+#define SCLK_DIV_ISP_VAL ((SPI1_ISP_RATIO << 12) \
+ | (SPI0_ISP_RATIO << 0))
+
+/* CLK_DIV_PERIL0 */
+#define UART5_RATIO 7
+#define UART4_RATIO 7
+#define UART3_RATIO 7
+#define UART2_RATIO 7
+#define UART1_RATIO 7
+#define UART0_RATIO 7
+
+#define CLK_DIV_PERIC0_VAL ((UART3_RATIO << 12) \
+ | (UART2_RATIO << 8) \
+ | (UART1_RATIO << 4) \
+ | (UART0_RATIO))
+/* CLK_DIV_PERIC1 */
+#define SPI1_RATIO 0x7
+#define SPI0_RATIO 0xf
+#define SPI1_SUB_RATIO 0x0
+#define SPI0_SUB_RATIO 0x0
+#define CLK_DIV_PERIC1_VAL ((SPI1_SUB_RATIO << 24) \
+ | ((SPI1_RATIO << 16) \
+ | (SPI0_SUB_RATIO << 8) \
+ | (SPI0_RATIO << 0)))
+
+/* CLK_DIV_PERIC2 */
+#define SPI2_RATIO 0xf
+#define SPI2_SUB_RATIO 0x0
+#define CLK_DIV_PERIC2_VAL ((SPI2_SUB_RATIO << 8) \
+ | (SPI2_RATIO << 0))
+
+/* CLK_DIV_PERIC3 */
+#define PWM_RATIO 8
+#define CLK_DIV_PERIC3_VAL (PWM_RATIO << 0)
+
+/* CLK_DIV_FSYS2 */
+#define MMC2_RATIO_MASK 0xf
+#define MMC2_RATIO_VAL 0x3
+#define MMC2_RATIO_OFFSET 0
+
+#define MMC2_PRE_RATIO_MASK 0xff
+#define MMC2_PRE_RATIO_VAL 0x9
+#define MMC2_PRE_RATIO_OFFSET 8
+
+#define MMC3_RATIO_MASK 0xf
+#define MMC3_RATIO_VAL 0x1
+#define MMC3_RATIO_OFFSET 16
+
+#define MMC3_PRE_RATIO_MASK 0xff
+#define MMC3_PRE_RATIO_VAL 0x0
+#define MMC3_PRE_RATIO_OFFSET 24
+
+/* CLK_SRC_LEX */
+#define CLK_SRC_LEX_VAL 0x0
+
+/* CLK_DIV_LEX */
+#define CLK_DIV_LEX_VAL 0x10
+
+/* CLK_DIV_R0X */
+#define CLK_DIV_R0X_VAL 0x10
+
+/* CLK_DIV_L0X */
+#define CLK_DIV_R1X_VAL 0x10
+
+/* CLK_DIV_ISP0 */
+#define CLK_DIV_ISP0_VAL 0x31
+
+/* CLK_DIV_ISP1 */
+#define CLK_DIV_ISP1_VAL 0x0
+
+/* CLK_DIV_ISP2 */
+#define CLK_DIV_ISP2_VAL 0x1
+
+/* CLK_SRC_DISP1_0 */
+#define CLK_SRC_DISP1_0_VAL 0x6
+
+/*
+ * DIV_DISP1_0
+ * For DP, divisor should be 2
+ */
+#define CLK_DIV_DISP1_0_FIMD1 (2 << 0)
+
+/* CLK_GATE_IP_DISP1 */
+#define CLK_GATE_DP1_ALLOW (1 << 4)
+
+#define DDR3PHY_CTRL_PHY_RESET (1 << 0)
+#define DDR3PHY_CTRL_PHY_RESET_OFF (0 << 0)
+
+#define PHY_CON0_RESET_VAL 0x17020a40
+#define P0_CMD_EN (1 << 14)
+#define BYTE_RDLVL_EN (1 << 13)
+#define CTRL_SHGATE (1 << 8)
+
+#define PHY_CON1_RESET_VAL 0x09210100
+#define CTRL_GATEDURADJ_MASK (0xf << 20)
+
+#define PHY_CON2_RESET_VAL 0x00010004
+#define INIT_DESKEW_EN (1 << 6)
+#define RDLVL_GATE_EN (1 << 24)
+
+/*ZQ Configurations */
+#define PHY_CON16_RESET_VAL 0x08000304
+
+#define ZQ_CLK_DIV_EN (1 << 18)
+#define ZQ_MANUAL_STR (1 << 1)
+#define ZQ_DONE (1 << 0)
+
+#define CTRL_RDLVL_GATE_ENABLE 1
+#define CTRL_RDLVL_GATE_DISABLE 1
+
+/* Direct Command */
+#define DIRECT_CMD_NOP 0x07000000
+#define DIRECT_CMD_PALL 0x01000000
+#define DIRECT_CMD_ZQINIT 0x0a000000
+#define DIRECT_CMD_CHANNEL_SHIFT 28
+#define DIRECT_CMD_CHIP_SHIFT 20
+
+/* DMC PHY Control0 register */
+#define PHY_CONTROL0_RESET_VAL 0x0
+#define MEM_TERM_EN (1 << 31) /* Termination enable for memory */
+#define PHY_TERM_EN (1 << 30) /* Termination enable for PHY */
+#define DMC_CTRL_SHGATE (1 << 29) /* Duration of DQS gating signal */
+#define FP_RSYNC (1 << 3) /* Force DLL resyncronization */
+
+/* Driver strength for CK, CKE, CS & CA */
+#define IMP_OUTPUT_DRV_40_OHM 0x5
+#define IMP_OUTPUT_DRV_30_OHM 0x7
+#define CA_CK_DRVR_DS_OFFSET 9
+#define CA_CKE_DRVR_DS_OFFSET 6
+#define CA_CS_DRVR_DS_OFFSET 3
+#define CA_ADR_DRVR_DS_OFFSET 0
+
+#define PHY_CON42_CTRL_BSTLEN_SHIFT 8
+#define PHY_CON42_CTRL_RDLAT_SHIFT 0
+
+struct mem_timings;
+
+/* Errors that we can encourter in low-level setup */
+enum {
+ SETUP_ERR_OK,
+ SETUP_ERR_RDLV_COMPLETE_TIMEOUT = -1,
+ SETUP_ERR_ZQ_CALIBRATION_FAILURE = -2,
+};
+
+/*
+ * Memory variant specific initialization code
+ *
+ * @param mem Memory timings for this memory type.
+ * @param mem_iv_size Memory interleaving size is a configurable parameter
+ * which the DMC uses to decide how to split a memory
+ * chunk into smaller chunks to support concurrent
+ * accesses; may vary across boards.
+ * @return 0 if ok, SETUP_ERR_... if there is a problem
+ */
+int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size);
+
+/*
+ * Configure ZQ I/O interface
+ *
+ * @param mem Memory timings for this memory type.
+ * @param phy0_ctrl Pointer to struct containing PHY0 control reg
+ * @param phy1_ctrl Pointer to struct containing PHY1 control reg
+ * @return 0 if ok, -1 on error
+ */
+int dmc_config_zq(struct mem_timings *mem,
+ struct exynos5_phy_control *phy0_ctrl,
+ struct exynos5_phy_control *phy1_ctrl);
+
+/*
+ * Send NOP and MRS/EMRS Direct commands
+ *
+ * @param mem Memory timings for this memory type.
+ * @param dmc Pointer to struct of DMC registers
+ */
+void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc);
+
+/*
+ * Send PALL Direct commands
+ *
+ * @param mem Memory timings for this memory type.
+ * @param dmc Pointer to struct of DMC registers
+ */
+void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc);
+
+/*
+ * Configure the memconfig and membaseconfig registers
+ *
+ * @param mem Memory timings for this memory type.
+ * @param exynos5_dmc Pointer to struct of DMC registers
+ */
+void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc);
+
+/*
+ * Reset the DLL. This function is common between DDR3 and LPDDR2.
+ * However, the reset value is different. So we are passing a flag
+ * ddr_mode to distinguish between LPDDR2 and DDR3.
+ *
+ * @param exynos5_dmc Pointer to struct of DMC registers
+ * @param ddr_mode Type of DDR memory
+ */
+void update_reset_dll(struct exynos5_dmc *, enum ddr_mode);
+
+void sdelay(unsigned long);
+void mem_ctrl_init(void);
+void system_clock_init(void);
+#endif
diff --git a/board/samsung/dts/exynos5250-arndale.dts b/board/samsung/dts/exynos5250-arndale.dts
new file mode 100644
index 0000000..3081ab4
--- /dev/null
+++ b/board/samsung/dts/exynos5250-arndale.dts
@@ -0,0 +1,23 @@
+/*
+ * SAMSUNG Arndale board device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+/include/ ARCH_CPU_DTS
+
+/ {
+ model = "SAMSUNG Arndale board based on EXYNOS5250";
+ compatible = "samsung,arndale", "samsung,exynos5250";
+
+ aliases {
+ serial0 = "/serial at 12C20000";
+ console = "/serial@12C20000";
+ };
+};
diff --git a/boards.cfg b/boards.cfg
index 1e598cb..38c1ac7 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -319,6 +319,7 @@ origen arm armv7 origen samsung exynos
s5pc210_universal arm armv7 universal_c210 samsung exynos
snow arm armv7 smdk5250 samsung exynos
smdk5250 arm armv7 smdk5250 samsung exynos
+arndale arm armv7 arndale samsung exynos
smdkv310 arm armv7 smdkv310 samsung exynos
trats arm armv7 trats samsung exynos
harmony arm armv7:arm720t harmony nvidia tegra20
diff --git a/include/configs/arndale.h b/include/configs/arndale.h
new file mode 100644
index 0000000..63d636e
--- /dev/null
+++ b/include/configs/arndale.h
@@ -0,0 +1,36 @@
+/*
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * Configuration settings for the SAMSUNG Arndale board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_ARNDALE_H
+#define __CONFIG_ARNDALE_H
+
+#include <configs/exynos5250-dt.h>
+
+#undef CONFIG_DEFAULT_DEVICE_TREE
+#define CONFIG_DEFAULT_DEVICE_TREE exynos5250-arndale
+
+#undef CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_IS_IN_MMC
+
+#endif /* __CONFIG_ARNDALE_H */
--
1.7.9.5
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [U-Boot] [PATCH v3 2/2] exynos5250: arndale: Add mmc support
2013-07-02 4:41 [U-Boot] [PATCH v3 0/2] Add Arndale board support Inderpal Singh
2013-07-02 4:41 ` [U-Boot] [PATCH v3 1/2] exynos5250: Add arndale " Inderpal Singh
@ 2013-07-02 4:41 ` Inderpal Singh
2013-07-02 5:55 ` [U-Boot] [PATCH v3 0/2] Add Arndale board support Chander Kashyap
2 siblings, 0 replies; 5+ messages in thread
From: Inderpal Singh @ 2013-07-02 4:41 UTC (permalink / raw)
To: u-boot
This patch adds mmc support to the arndale board.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
---
board/samsung/arndale/arndale.c | 14 ++++++++++++++
board/samsung/dts/exynos5250-arndale.dts | 18 ++++++++++++++++++
2 files changed, 32 insertions(+)
diff --git a/board/samsung/arndale/arndale.c b/board/samsung/arndale/arndale.c
index 627583b..7f8a568 100644
--- a/board/samsung/arndale/arndale.c
+++ b/board/samsung/arndale/arndale.c
@@ -22,6 +22,7 @@
#include <common.h>
#include <asm/arch/pinmux.h>
+#include <asm/arch/dwmmc.h>
#include <asm/arch/power.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -64,6 +65,19 @@ void dram_init_banksize(void)
}
}
+#ifdef CONFIG_GENERIC_MMC
+int board_mmc_init(bd_t *bis)
+{
+ int ret;
+ /* dwmmc initializattion for available channels */
+ ret = exynos_dwmmc_init(gd->fdt_blob);
+ if (ret)
+ debug("dwmmc init failed\n");
+
+ return ret;
+}
+#endif
+
static int board_uart_init(void)
{
int err, uart_id, ret = 0;
diff --git a/board/samsung/dts/exynos5250-arndale.dts b/board/samsung/dts/exynos5250-arndale.dts
index 3081ab4..948275a 100644
--- a/board/samsung/dts/exynos5250-arndale.dts
+++ b/board/samsung/dts/exynos5250-arndale.dts
@@ -20,4 +20,22 @@
serial0 = "/serial at 12C20000";
console = "/serial at 12C20000";
};
+
+ mmc at 12200000 {
+ samsung,bus-width = <8>;
+ samsung,timing = <1 3 3>;
+ };
+
+ mmc at 12210000 {
+ status = "disabled";
+ };
+
+ mmc at 12220000 {
+ samsung,bus-width = <4>;
+ samsung,timing = <1 2 3>;
+ };
+
+ mmc at 12230000 {
+ status = "disabled";
+ };
};
--
1.7.9.5
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [U-Boot] [PATCH v3 0/2] Add Arndale board support
2013-07-02 4:41 [U-Boot] [PATCH v3 0/2] Add Arndale board support Inderpal Singh
2013-07-02 4:41 ` [U-Boot] [PATCH v3 1/2] exynos5250: Add arndale " Inderpal Singh
2013-07-02 4:41 ` [U-Boot] [PATCH v3 2/2] exynos5250: arndale: Add mmc support Inderpal Singh
@ 2013-07-02 5:55 ` Chander Kashyap
2 siblings, 0 replies; 5+ messages in thread
From: Chander Kashyap @ 2013-07-02 5:55 UTC (permalink / raw)
To: u-boot
Dear Inder,
On 2 July 2013 10:11, Inderpal Singh <inderpal.singh@linaro.org> wrote:
> The Arndale board is based on samsung's exynos5250 SOC.
> For spl generation, it depends on the patch at [5].
>
> First patch provides the basic arndale board support. The second patch
> adds the MMC support.
>
> Changes in v2:
> - split from earlier patchset at [3] as per Minkyu
> - Removed checkpatch errors pointed out by Wolfgang
> - rebased to latest u-boot-samsung master branch
> - created mmc_boot.c to remove dependency on consolidation
> patch at [4]
> - split the mmc support to new patch as it depends on [2]
>
> [1] http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/162883
> [2] http://comments.gmane.org/gmane.comp.boot-loaders.u-boot/159887
> [3] http://comments.gmane.org/gmane.comp.boot-loaders.u-boot/157101
> [4] http://comments.gmane.org/gmane.comp.boot-loaders.u-boot/156272
>
> Changes in v3:
> - Used dt based serial
> - rebased to latest u-boot-samsung master branch
>
> [5] http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/164824
>
> Inderpal Singh (2):
> exynos5250: Add arndale board support
> exynos5250: arndale: Add mmc support
>
> MAINTAINERS | 4 +
> board/samsung/arndale/Makefile | 58 +++
> board/samsung/arndale/arndale.c | 117 ++++++
> board/samsung/arndale/arndale_spl.c | 66 +++
> board/samsung/arndale/clock_init.c | 655 ++++++++++++++++++++++++++++++
> board/samsung/arndale/clock_init.h | 149 +++++++
> board/samsung/arndale/dmc_common.c | 199 +++++++++
> board/samsung/arndale/dmc_init_ddr3.c | 228 +++++++++++
> board/samsung/arndale/lowlevel_init.S | 92 +++++
> board/samsung/arndale/mmc_boot.c | 58 +++
> board/samsung/arndale/setup.h | 569 ++++++++++++++++++++++++++
> board/samsung/dts/exynos5250-arndale.dts | 41 ++
> boards.cfg | 1 +
> include/configs/arndale.h | 36 ++
> 14 files changed, 2273 insertions(+)
> create mode 100644 board/samsung/arndale/Makefile
> create mode 100644 board/samsung/arndale/arndale.c
> create mode 100644 board/samsung/arndale/arndale_spl.c
> create mode 100644 board/samsung/arndale/clock_init.c
> create mode 100644 board/samsung/arndale/clock_init.h
> create mode 100644 board/samsung/arndale/dmc_common.c
> create mode 100644 board/samsung/arndale/dmc_init_ddr3.c
> create mode 100644 board/samsung/arndale/lowlevel_init.S
> create mode 100644 board/samsung/arndale/mmc_boot.c
> create mode 100644 board/samsung/arndale/setup.h
> create mode 100644 board/samsung/dts/exynos5250-arndale.dts
> create mode 100644 include/configs/arndale.h
>
> --
> 1.7.9.5
>
Looks good.
Acked-by: Chander Kashyap <chander.kashyap@gmail.com>
--
with warm regards,
Chander Kashyap
^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot] [PATCH v3 1/2] exynos5250: Add arndale board support
2013-07-02 4:41 ` [U-Boot] [PATCH v3 1/2] exynos5250: Add arndale " Inderpal Singh
@ 2013-07-02 6:36 ` Minkyu Kang
0 siblings, 0 replies; 5+ messages in thread
From: Minkyu Kang @ 2013-07-02 6:36 UTC (permalink / raw)
To: u-boot
Dear Inderpal Singh,
On 02/07/13 13:41, Inderpal Singh wrote:
> Arndale board is based on samsung's exynos5250 soc.
>
> Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
> ---
> MAINTAINERS | 4 +
> board/samsung/arndale/Makefile | 58 +++
> board/samsung/arndale/arndale.c | 103 +++++
> board/samsung/arndale/arndale_spl.c | 66 +++
> board/samsung/arndale/clock_init.c | 655 ++++++++++++++++++++++++++++++
> board/samsung/arndale/clock_init.h | 149 +++++++
> board/samsung/arndale/dmc_common.c | 199 +++++++++
> board/samsung/arndale/dmc_init_ddr3.c | 228 +++++++++++
> board/samsung/arndale/lowlevel_init.S | 92 +++++
> board/samsung/arndale/mmc_boot.c | 58 +++
> board/samsung/arndale/setup.h | 569 ++++++++++++++++++++++++++
> board/samsung/dts/exynos5250-arndale.dts | 23 ++
> boards.cfg | 1 +
> include/configs/arndale.h | 36 ++
> 14 files changed, 2241 insertions(+)
> create mode 100644 board/samsung/arndale/Makefile
> create mode 100644 board/samsung/arndale/arndale.c
> create mode 100644 board/samsung/arndale/arndale_spl.c
> create mode 100644 board/samsung/arndale/clock_init.c
> create mode 100644 board/samsung/arndale/clock_init.h
> create mode 100644 board/samsung/arndale/dmc_common.c
> create mode 100644 board/samsung/arndale/dmc_init_ddr3.c
> create mode 100644 board/samsung/arndale/lowlevel_init.S
> create mode 100644 board/samsung/arndale/mmc_boot.c
> create mode 100644 board/samsung/arndale/setup.h
> create mode 100644 board/samsung/dts/exynos5250-arndale.dts
> create mode 100644 include/configs/arndale.h
>
This patch seems to conflict with Rajeshwari's patch.
http://patchwork.ozlabs.org/patch/256058/
So, this patch will be pending until merge.
Thanks,
Minkyu Kang.
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2013-07-02 6:36 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2013-07-02 4:41 [U-Boot] [PATCH v3 0/2] Add Arndale board support Inderpal Singh
2013-07-02 4:41 ` [U-Boot] [PATCH v3 1/2] exynos5250: Add arndale " Inderpal Singh
2013-07-02 6:36 ` Minkyu Kang
2013-07-02 4:41 ` [U-Boot] [PATCH v3 2/2] exynos5250: arndale: Add mmc support Inderpal Singh
2013-07-02 5:55 ` [U-Boot] [PATCH v3 0/2] Add Arndale board support Chander Kashyap
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.