[PATCH 0/3] ARM: dts: mxs: dcp cleanup patches

[PATCH 0/3] ARM: dts: mxs: dcp cleanup patches

[Lothar Waßmann]

This patch series does the following:

- let the driver be "disabled" by default in imx28.dtsi
- coding style cleanups in drivers/crypto/dcp.c
- use the "official" 'fsl,' prefix in the 'compatible' property

The last patch adds a new entry to the of_match_table of the driver,
so that current DT blobs will still work. When out of tree users
(mentioned in the commit log of 519d8b1a "Added support for
Freescale's DCP co-processor") have updated their DTBs the old entry
'fsl-dsp' can be removed from the driver.

This patch series requires at least
"[PATCH 2/8] ARM: dts: mxs: add labels to most nodes for easier reference"
from the patch series:
<1375966287-6784-1-git-send-email-LW@KARO-electronics.de> to be
applied.

 arch/arm/boot/dts/imx28.dtsi      |    2 +-
 b/arch/arm/boot/dts/imx28-evk.dts |    4 ++++
 b/arch/arm/boot/dts/imx28.dtsi    |    3 ++-
 b/drivers/crypto/dcp.c            |   11 +++++------
 drivers/crypto/dcp.c              |    2 ++
 5 files changed, 14 insertions(+), 8 deletions(-)

[PATCH 0/3] ARM: dts: mxs: dcp cleanup patches

[Lothar Waßmann]

This patch series does the following:

- let the driver be "disabled" by default in imx28.dtsi
- coding style cleanups in drivers/crypto/dcp.c
- use the "official" 'fsl,' prefix in the 'compatible' property

The last patch adds a new entry to the of_match_table of the driver,
so that current DT blobs will still work. When out of tree users
(mentioned in the commit log of 519d8b1a "Added support for
Freescale's DCP co-processor") have updated their DTBs the old entry
'fsl-dsp' can be removed from the driver.

This patch series requires at least
"[PATCH 2/8] ARM: dts: mxs: add labels to most nodes for easier reference"
from the patch series:
<1375966287-6784-1-git-send-email-LW@KARO-electronics.de> to be
applied.

 arch/arm/boot/dts/imx28.dtsi      |    2 +-
 b/arch/arm/boot/dts/imx28-evk.dts |    4 ++++
 b/arch/arm/boot/dts/imx28.dtsi    |    3 ++-
 b/drivers/crypto/dcp.c            |   11 +++++------
 drivers/crypto/dcp.c              |    2 ++
 5 files changed, 14 insertions(+), 8 deletions(-)

[PATCH 1/3] ARM: dts: mxs: set dcp to "disabled" by default

[Lothar Waßmann]

Reintroduce 'status = "disabled"' for the dcp node that was dropped by
commit 519d8b1a "Added support for Freescale's DCP co-processor".

Explicitly enable it in imx28-evk which is referenced in the commit
message of that commit.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
 arch/arm/boot/dts/imx28-evk.dts |    4 ++++
 arch/arm/boot/dts/imx28.dtsi    |    3 ++-
 2 files changed, 6 insertions(+), 1 deletions(-)

diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
index dff2279..ac790bb 100644
--- a/arch/arm/boot/dts/imx28-evk.dts
+++ b/arch/arm/boot/dts/imx28-evk.dts
@@ -361,3 +361,7 @@
 		default-brightness-level = <6>;
 	};
 };
+
+&dcp {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index e459d63..ea99d09 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -794,9 +794,10 @@
 			};
 
 			dcp: dcp@80028000 {
+				compatible = "fsl-dcp";
 				reg = <0x80028000 0x2000>;
 				interrupts = <52 53 54>;
-				compatible = "fsl-dcp";
+				status = "disabled";
 			};
 
 			pxp: pxp@8002a000 {
-- 
1.7.2.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/3] ARM: dts: mxs: set dcp to "disabled" by default

[Lothar Waßmann]

Reintroduce 'status = "disabled"' for the dcp node that was dropped by
commit 519d8b1a "Added support for Freescale's DCP co-processor".

Explicitly enable it in imx28-evk which is referenced in the commit
message of that commit.

Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
 arch/arm/boot/dts/imx28-evk.dts |    4 ++++
 arch/arm/boot/dts/imx28.dtsi    |    3 ++-
 2 files changed, 6 insertions(+), 1 deletions(-)

diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
index dff2279..ac790bb 100644
--- a/arch/arm/boot/dts/imx28-evk.dts
+++ b/arch/arm/boot/dts/imx28-evk.dts
@@ -361,3 +361,7 @@
 		default-brightness-level = <6>;
 	};
 };
+
+&dcp {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index e459d63..ea99d09 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -794,9 +794,10 @@
 			};
 
 			dcp: dcp at 80028000 {
+				compatible = "fsl-dcp";
 				reg = <0x80028000 0x2000>;
 				interrupts = <52 53 54>;
-				compatible = "fsl-dcp";
+				status = "disabled";
 			};
 
 			pxp: pxp at 8002a000 {
-- 
1.7.2.5

Re: [PATCH 1/3] ARM: dts: mxs: set dcp to "disabled" by default

[Shawn Guo]

On Thu, Aug 08, 2013 at 03:30:27PM +0200, Lothar Waßmann wrote:
> Reintroduce 'status = "disabled"' for the dcp node that was dropped by
> commit 519d8b1a "Added support for Freescale's DCP co-processor".

For IP blocks that do not have pins to be routed on boards, it should be
fine to have it enabled in <soc>.dtsi.

Shawn

> 
> Explicitly enable it in imx28-evk which is referenced in the commit
> message of that commit.
> 
> Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
> ---
>  arch/arm/boot/dts/imx28-evk.dts |    4 ++++
>  arch/arm/boot/dts/imx28.dtsi    |    3 ++-
>  2 files changed, 6 insertions(+), 1 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
> index dff2279..ac790bb 100644
> --- a/arch/arm/boot/dts/imx28-evk.dts
> +++ b/arch/arm/boot/dts/imx28-evk.dts
> @@ -361,3 +361,7 @@
>  		default-brightness-level = <6>;
>  	};
>  };
> +
> +&dcp {
> +	status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
> index e459d63..ea99d09 100644
> --- a/arch/arm/boot/dts/imx28.dtsi
> +++ b/arch/arm/boot/dts/imx28.dtsi
> @@ -794,9 +794,10 @@
>  			};
>  
>  			dcp: dcp@80028000 {
> +				compatible = "fsl-dcp";
>  				reg = <0x80028000 0x2000>;
>  				interrupts = <52 53 54>;
> -				compatible = "fsl-dcp";
> +				status = "disabled";
>  			};
>  
>  			pxp: pxp@8002a000 {
> -- 
> 1.7.2.5
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/3] ARM: dts: mxs: set dcp to "disabled" by default

[Shawn Guo]

On Thu, Aug 08, 2013 at 03:30:27PM +0200, Lothar Wa?mann wrote:
> Reintroduce 'status = "disabled"' for the dcp node that was dropped by
> commit 519d8b1a "Added support for Freescale's DCP co-processor".

For IP blocks that do not have pins to be routed on boards, it should be
fine to have it enabled in <soc>.dtsi.

Shawn

> 
> Explicitly enable it in imx28-evk which is referenced in the commit
> message of that commit.
> 
> Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
> ---
>  arch/arm/boot/dts/imx28-evk.dts |    4 ++++
>  arch/arm/boot/dts/imx28.dtsi    |    3 ++-
>  2 files changed, 6 insertions(+), 1 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
> index dff2279..ac790bb 100644
> --- a/arch/arm/boot/dts/imx28-evk.dts
> +++ b/arch/arm/boot/dts/imx28-evk.dts
> @@ -361,3 +361,7 @@
>  		default-brightness-level = <6>;
>  	};
>  };
> +
> +&dcp {
> +	status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
> index e459d63..ea99d09 100644
> --- a/arch/arm/boot/dts/imx28.dtsi
> +++ b/arch/arm/boot/dts/imx28.dtsi
> @@ -794,9 +794,10 @@
>  			};
>  
>  			dcp: dcp at 80028000 {
> +				compatible = "fsl-dcp";
>  				reg = <0x80028000 0x2000>;
>  				interrupts = <52 53 54>;
> -				compatible = "fsl-dcp";
> +				status = "disabled";
>  			};
>  
>  			pxp: pxp at 8002a000 {
> -- 
> 1.7.2.5
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/3] ARM: dts: mxs: set dcp to "disabled" by default

[Lothar Waßmann]

Hi,

Shawn Guo writes:
> On Thu, Aug 08, 2013 at 03:30:27PM +0200, Lothar Waßmann wrote:
> > Reintroduce 'status = "disabled"' for the dcp node that was dropped by
> > commit 519d8b1a "Added support for Freescale's DCP co-processor".
> 
> For IP blocks that do not have pins to be routed on boards, it should be
> fine to have it enabled in <soc>.dtsi.
> 
That means that when a new driver is added, it will start wasting
resources on all board using that SoC unless the board maintainers
explicitly disable that driver in DTB.

I would prefer things to be the other way:
New drivers (no matter whether for chip-internal or external hardware)
should require to be explicitly enabled for those platforms on which
they are being used.


Lothar Waßmann
-- 
___________________________________________________________

Ka-Ro electronics GmbH | Pascalstraße 22 | D - 52076 Aachen
Phone: +49 2408 1402-0 | Fax: +49 2408 1402-10
Geschäftsführer: Matthias Kaussen
Handelsregistereintrag: Amtsgericht Aachen, HRB 4996

www.karo-electronics.de | info@karo-electronics.de
___________________________________________________________

[PATCH 1/3] ARM: dts: mxs: set dcp to "disabled" by default

[Lothar Waßmann]

Hi,

Shawn Guo writes:
> On Thu, Aug 08, 2013 at 03:30:27PM +0200, Lothar Wa?mann wrote:
> > Reintroduce 'status = "disabled"' for the dcp node that was dropped by
> > commit 519d8b1a "Added support for Freescale's DCP co-processor".
> 
> For IP blocks that do not have pins to be routed on boards, it should be
> fine to have it enabled in <soc>.dtsi.
> 
That means that when a new driver is added, it will start wasting
resources on all board using that SoC unless the board maintainers
explicitly disable that driver in DTB.

I would prefer things to be the other way:
New drivers (no matter whether for chip-internal or external hardware)
should require to be explicitly enabled for those platforms on which
they are being used.


Lothar Wa?mann
-- 
___________________________________________________________

Ka-Ro electronics GmbH | Pascalstra?e 22 | D - 52076 Aachen
Phone: +49 2408 1402-0 | Fax: +49 2408 1402-10
Gesch?ftsf?hrer: Matthias Kaussen
Handelsregistereintrag: Amtsgericht Aachen, HRB 4996

www.karo-electronics.de | info at karo-electronics.de
___________________________________________________________

Re: [PATCH 1/3] ARM: dts: mxs: set dcp to "disabled" by default

[Kumar Gala]

On Aug 12, 2013, at 7:05 AM, Lothar Waßmann wrote:

> Hi,
> 
> Shawn Guo writes:
>> On Thu, Aug 08, 2013 at 03:30:27PM +0200, Lothar Waßmann wrote:
>>> Reintroduce 'status = "disabled"' for the dcp node that was dropped by
>>> commit 519d8b1a "Added support for Freescale's DCP co-processor".
>> 
>> For IP blocks that do not have pins to be routed on boards, it should be
>> fine to have it enabled in <soc>.dtsi.
>> 
> That means that when a new driver is added, it will start wasting
> resources on all board using that SoC unless the board maintainers
> explicitly disable that driver in DTB.
> 
> I would prefer things to be the other way:
> New drivers (no matter whether for chip-internal or external hardware)
> should require to be explicitly enabled for those platforms on which
> they are being used.

But that enablement should be in the kernel and not the device tree.  The device tree is describing the HW, if the DCP exists and is usable w/o an external IO than by default it should be enabled in the SoC .dts

- k

--
Employee of Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation

[PATCH 1/3] ARM: dts: mxs: set dcp to "disabled" by default

[Kumar Gala]

On Aug 12, 2013, at 7:05 AM, Lothar Wa?mann wrote:

> Hi,
> 
> Shawn Guo writes:
>> On Thu, Aug 08, 2013 at 03:30:27PM +0200, Lothar Wa?mann wrote:
>>> Reintroduce 'status = "disabled"' for the dcp node that was dropped by
>>> commit 519d8b1a "Added support for Freescale's DCP co-processor".
>> 
>> For IP blocks that do not have pins to be routed on boards, it should be
>> fine to have it enabled in <soc>.dtsi.
>> 
> That means that when a new driver is added, it will start wasting
> resources on all board using that SoC unless the board maintainers
> explicitly disable that driver in DTB.
> 
> I would prefer things to be the other way:
> New drivers (no matter whether for chip-internal or external hardware)
> should require to be explicitly enabled for those platforms on which
> they are being used.

But that enablement should be in the kernel and not the device tree.  The device tree is describing the HW, if the DCP exists and is usable w/o an external IO than by default it should be enabled in the SoC .dts

- k

--
Employee of Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation

[PATCH 2/3] crypto: dcp - cleanup: commas at end of struct initializers where appropriate

[Lothar Waßmann]

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
 drivers/crypto/dcp.c |   11 +++++------
 1 files changed, 5 insertions(+), 6 deletions(-)

diff --git a/drivers/crypto/dcp.c b/drivers/crypto/dcp.c
index a8a7dd4..6a2495e 100644
--- a/drivers/crypto/dcp.c
+++ b/drivers/crypto/dcp.c
@@ -651,8 +651,7 @@ static struct crypto_alg algs[] = {
 			.encrypt = dcp_aes_cbc_encrypt,
 			.decrypt = dcp_aes_cbc_decrypt,
 			.ivsize = AES_KEYSIZE_128,
-		}
-
+		},
 	},
 };
 
@@ -890,8 +889,8 @@ static int dcp_remove(struct platform_device *pdev)
 }
 
 static struct of_device_id fs_dcp_of_match[] = {
-	{	.compatible = "fsl-dcp"},
-	{},
+	{ .compatible = "fsl-dcp", },
+	{}
 };
 
 static struct platform_driver fs_dcp_driver = {
@@ -900,8 +899,8 @@ static struct platform_driver fs_dcp_driver = {
 	.driver = {
 		.name = "fsl-dcp",
 		.owner = THIS_MODULE,
-		.of_match_table = fs_dcp_of_match
-	}
+		.of_match_table = fs_dcp_of_match,
+	},
 };
 
 module_platform_driver(fs_dcp_driver);
-- 
1.7.2.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/3] crypto: dcp - cleanup: commas at end of struct initializers where appropriate

[Lothar Waßmann]

Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
 drivers/crypto/dcp.c |   11 +++++------
 1 files changed, 5 insertions(+), 6 deletions(-)

diff --git a/drivers/crypto/dcp.c b/drivers/crypto/dcp.c
index a8a7dd4..6a2495e 100644
--- a/drivers/crypto/dcp.c
+++ b/drivers/crypto/dcp.c
@@ -651,8 +651,7 @@ static struct crypto_alg algs[] = {
 			.encrypt = dcp_aes_cbc_encrypt,
 			.decrypt = dcp_aes_cbc_decrypt,
 			.ivsize = AES_KEYSIZE_128,
-		}
-
+		},
 	},
 };
 
@@ -890,8 +889,8 @@ static int dcp_remove(struct platform_device *pdev)
 }
 
 static struct of_device_id fs_dcp_of_match[] = {
-	{	.compatible = "fsl-dcp"},
-	{},
+	{ .compatible = "fsl-dcp", },
+	{}
 };
 
 static struct platform_driver fs_dcp_driver = {
@@ -900,8 +899,8 @@ static struct platform_driver fs_dcp_driver = {
 	.driver = {
 		.name = "fsl-dcp",
 		.owner = THIS_MODULE,
-		.of_match_table = fs_dcp_of_match
-	}
+		.of_match_table = fs_dcp_of_match,
+	},
 };
 
 module_platform_driver(fs_dcp_driver);
-- 
1.7.2.5

[PATCH 3/3] crypto: dcp: rename 'compatible' property to 'fsl,dcp'

[Lothar Waßmann]

Leave the old 'fsl-dcp' value in place with an appropriate comment
until external users have updated their DTBs.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
 arch/arm/boot/dts/imx28.dtsi |    2 +-
 drivers/crypto/dcp.c         |    2 ++
 2 files changed, 3 insertions(+), 1 deletions(-)

diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index ea99d09..0584935 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -794,7 +794,7 @@
 			};
 
 			dcp: dcp@80028000 {
-				compatible = "fsl-dcp";
+				compatible = "fsl,dcp";
 				reg = <0x80028000 0x2000>;
 				interrupts = <52 53 54>;
 				status = "disabled";
diff --git a/drivers/crypto/dcp.c b/drivers/crypto/dcp.c
index 6a2495e..72196c0 100644
--- a/drivers/crypto/dcp.c
+++ b/drivers/crypto/dcp.c
@@ -889,6 +889,8 @@ static int dcp_remove(struct platform_device *pdev)
 }
 
 static struct of_device_id fs_dcp_of_match[] = {
+	{ .compatible = "fsl,dcp", },
+	/* To be removed when the DT blobs referencing this have been updated */
 	{ .compatible = "fsl-dcp", },
 	{}
 };
-- 
1.7.2.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 3/3] crypto: dcp: rename 'compatible' property to 'fsl,dcp'

[Lothar Waßmann]

Leave the old 'fsl-dcp' value in place with an appropriate comment
until external users have updated their DTBs.

Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
 arch/arm/boot/dts/imx28.dtsi |    2 +-
 drivers/crypto/dcp.c         |    2 ++
 2 files changed, 3 insertions(+), 1 deletions(-)

diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index ea99d09..0584935 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -794,7 +794,7 @@
 			};
 
 			dcp: dcp at 80028000 {
-				compatible = "fsl-dcp";
+				compatible = "fsl,dcp";
 				reg = <0x80028000 0x2000>;
 				interrupts = <52 53 54>;
 				status = "disabled";
diff --git a/drivers/crypto/dcp.c b/drivers/crypto/dcp.c
index 6a2495e..72196c0 100644
--- a/drivers/crypto/dcp.c
+++ b/drivers/crypto/dcp.c
@@ -889,6 +889,8 @@ static int dcp_remove(struct platform_device *pdev)
 }
 
 static struct of_device_id fs_dcp_of_match[] = {
+	{ .compatible = "fsl,dcp", },
+	/* To be removed when the DT blobs referencing this have been updated */
 	{ .compatible = "fsl-dcp", },
 	{}
 };
-- 
1.7.2.5

Re: [PATCH 3/3] crypto: dcp: rename 'compatible' property to 'fsl,dcp'

[Sergei Shtylyov]

Hello.

On 08/08/2013 05:30 PM, Lothar Waßmann wrote:

> Leave the old 'fsl-dcp' value in place with an appropriate comment
> until external users have updated their DTBs.

> Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
> ---
>   arch/arm/boot/dts/imx28.dtsi |    2 +-
>   drivers/crypto/dcp.c         |    2 ++
>   2 files changed, 3 insertions(+), 1 deletions(-)

> diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
> index ea99d09..0584935 100644
> --- a/arch/arm/boot/dts/imx28.dtsi
> +++ b/arch/arm/boot/dts/imx28.dtsi
> @@ -794,7 +794,7 @@
>   			};
>
>   			dcp: dcp@80028000 {

     By the way, I see that this is a crypto device, so it should be named 
"crypto" according to ePAPR spec. [1]

> -				compatible = "fsl-dcp";
> +				compatible = "fsl,dcp";
>   				reg = <0x80028000 0x2000>;
>   				interrupts = <52 53 54>;
>   				status = "disabled";

[1] http://www.power.org/resources/downloads/Power_ePAPR_APPROVED_v1.0.pdf

WBR, Sergei

[PATCH 3/3] crypto: dcp: rename 'compatible' property to 'fsl, dcp'

[Sergei Shtylyov]

Hello.

On 08/08/2013 05:30 PM, Lothar Wa?mann wrote:

> Leave the old 'fsl-dcp' value in place with an appropriate comment
> until external users have updated their DTBs.

> Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
> ---
>   arch/arm/boot/dts/imx28.dtsi |    2 +-
>   drivers/crypto/dcp.c         |    2 ++
>   2 files changed, 3 insertions(+), 1 deletions(-)

> diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
> index ea99d09..0584935 100644
> --- a/arch/arm/boot/dts/imx28.dtsi
> +++ b/arch/arm/boot/dts/imx28.dtsi
> @@ -794,7 +794,7 @@
>   			};
>
>   			dcp: dcp at 80028000 {

     By the way, I see that this is a crypto device, so it should be named 
"crypto" according to ePAPR spec. [1]

> -				compatible = "fsl-dcp";
> +				compatible = "fsl,dcp";
>   				reg = <0x80028000 0x2000>;
>   				interrupts = <52 53 54>;
>   				status = "disabled";

[1] http://www.power.org/resources/downloads/Power_ePAPR_APPROVED_v1.0.pdf

WBR, Sergei

Re: [PATCH 0/3] ARM: dts: mxs: dcp cleanup patches

[Kumar Gala]

On Aug 8, 2013, at 8:30 AM, Lothar Waßmann wrote:

> This patch series does the following:
> 
> - let the driver be "disabled" by default in imx28.dtsi
> - coding style cleanups in drivers/crypto/dcp.c
> - use the "official" 'fsl,' prefix in the 'compatible' property
> 
> The last patch adds a new entry to the of_match_table of the driver,
> so that current DT blobs will still work. When out of tree users
> (mentioned in the commit log of 519d8b1a "Added support for
> Freescale's DCP co-processor") have updated their DTBs the old entry
> 'fsl-dsp' can be removed from the driver.
> 
> This patch series requires at least
> "[PATCH 2/8] ARM: dts: mxs: add labels to most nodes for easier reference"
> from the patch series:
> <1375966287-6784-1-git-send-email-LW@KARO-electronics.de> to be
> applied.
> 
> arch/arm/boot/dts/imx28.dtsi      |    2 +-
> b/arch/arm/boot/dts/imx28-evk.dts |    4 ++++
> b/arch/arm/boot/dts/imx28.dtsi    |    3 ++-
> b/drivers/crypto/dcp.c            |   11 +++++------
> drivers/crypto/dcp.c              |    2 ++
> 5 files changed, 14 insertions(+), 8 deletions(-)
> 
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

Is there an actual binding spec for fsl,dcp?  If not, there really should be.

- k

--
Employee of Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation

[PATCH 0/3] ARM: dts: mxs: dcp cleanup patches

[Kumar Gala]

On Aug 8, 2013, at 8:30 AM, Lothar Wa?mann wrote:

> This patch series does the following:
> 
> - let the driver be "disabled" by default in imx28.dtsi
> - coding style cleanups in drivers/crypto/dcp.c
> - use the "official" 'fsl,' prefix in the 'compatible' property
> 
> The last patch adds a new entry to the of_match_table of the driver,
> so that current DT blobs will still work. When out of tree users
> (mentioned in the commit log of 519d8b1a "Added support for
> Freescale's DCP co-processor") have updated their DTBs the old entry
> 'fsl-dsp' can be removed from the driver.
> 
> This patch series requires at least
> "[PATCH 2/8] ARM: dts: mxs: add labels to most nodes for easier reference"
> from the patch series:
> <1375966287-6784-1-git-send-email-LW@KARO-electronics.de> to be
> applied.
> 
> arch/arm/boot/dts/imx28.dtsi      |    2 +-
> b/arch/arm/boot/dts/imx28-evk.dts |    4 ++++
> b/arch/arm/boot/dts/imx28.dtsi    |    3 ++-
> b/drivers/crypto/dcp.c            |   11 +++++------
> drivers/crypto/dcp.c              |    2 ++
> 5 files changed, 14 insertions(+), 8 deletions(-)
> 
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

Is there an actual binding spec for fsl,dcp?  If not, there really should be.

- k

--
Employee of Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation