Re: [PATCH 1/2] arm64: dts: rockchip: Add core dts for RK3308 SOC

[Heiko Stuebner <heiko-4mtYJXux2i+zQB+pC5nmwQ@public.gmane.org>]

Hi Andy,

Am Donnerstag, 17. Oktober 2019, 05:04:49 CEST schrieb Andy Yan:

> +	psci {
> +		compatible = "arm,psci-1.0";
> +		method = "smc";
> +	};

Please also provide a ATF implementation for the rk3308 :-)
[Not a requirement for getting this merged, but it would be
really cool to have sources for the full stack]

> +
> +	ramoops_mem: ramoops_mem {
> +		reg = <0x0 0x110000 0x0 0xf0000>;
> +		reg-names = "ramoops_mem";
> +	};
> +
> +	ramoops: ramoops {
> +		compatible = "ramoops";
> +		record-size = <0x0 0x30000>;
> +		console-size = <0x0 0xc0000>;
> +		ftrace-size = <0x0 0x00000>;
> +		pmsg-size = <0x0 0x00000>;
> +		memory-region = <&ramoops_mem>;
> +	};

I think ramoops are more a per-board thing, like for the evb.
As they'll require cooperation with bootloaders to not mangle that
memory area. For this please also coordinate with Kever because
I somehow remember we have u-boot sometimes at 0x100000.


> +	grf: grf@ff000000 {
> +		compatible = "rockchip,rk3308-grf", "syscon", "simple-mfd";

Please add a patch adding the rockchip,rk3308-grf compatible to
Documentation/devicetree/bindings/soc/rockchip/grf.txt

> +		reg = <0x0 0xff000000 0x0 0x10000>;
> +
> +		reboot-mode {
> +			compatible = "syscon-reboot-mode";
> +			offset = <0x500>;
> +			mode-bootloader = <BOOT_BL_DOWNLOAD>;
> +			mode-loader = <BOOT_BL_DOWNLOAD>;
> +			mode-normal = <BOOT_NORMAL>;
> +			mode-recovery = <BOOT_RECOVERY>;
> +			mode-fastboot = <BOOT_FASTBOOT>;
> +		};
> +	};
> +
> +	detect_grf: syscon@ff00b000 {
> +		compatible = "syscon", "simple-mfd";

	compatible = "rockchip,rk3308-detect-grf", "syscon"
+ add the rk3308-detect-grf to the binding

> +		reg = <0x0 0xff00b000 0x0 0x1000>;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +	};
> +
> +	core_grf: syscon@ff00c000 {
> +		compatible = "syscon", "simple-mfd";

same as detect_grf

> +		reg = <0x0 0xff00c000 0x0 0x1000>;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +
> +	};
> +
> +	i2c0: i2c@ff040000 {
> +		compatible = "rockchip,rk3399-i2c";

	compatible = "rockchip,rk3308-i2c", "rockchip,rk3399-i2c";
Same for all i2c controllers.

> +		reg = <0x0 0xff040000 0x0 0x1000>;
> +		clocks = <&cru SCLK_I2C0>, <&cru PCLK_I2C0>;
> +		clock-names = "i2c", "pclk";
> +		interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&i2c0_xfer>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		status = "disabled";
> +	};


> +	spi0: spi@ff120000 {
> +		compatible = "rockchip,rk3308-spi", "rockchip,rk3066-spi";
> +		reg = <0x0 0xff120000 0x0 0x1000>;
> +		interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>;
> +		clock-names = "spiclk", "apb_pclk";
> +		dmas = <&dmac0 0>, <&dmac0 1>;
> +		dma-names = "tx", "rx";
> +		pinctrl-names = "default", "high_speed";

there is no high_speed pinctrl defined for the Rockchip spi driver
in mainline, so this part should go away in a first step.
Same for the other spi controllers.

> +		pinctrl-0 = <&spi0_clk &spi0_csn0 &spi0_miso &spi0_mosi>;
> +		pinctrl-1 = <&spi0_clk_hs &spi0_csn0 &spi0_miso_hs &spi0_mosi_hs>;
> +		status = "disabled";
> +	};


> +	rktimer: rktimer@ff1a0000 {
> +		compatible = "rockchip,rk3288-timer";

	compatible = "rockchip,rk3308-timer", "rockchip,rk3288-timer";

> +		reg = <0x0 0xff1a0000 0x0 0x20>;
> +		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> +		clocks = <&cru PCLK_TIMER>, <&cru SCLK_TIMER0>;
> +		clock-names = "pclk", "timer";
> +	};



> +	amba {
> +		compatible = "arm,amba-bus";

compatible = "simple-bus";

> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		dmac0: dma-controller@ff2c0000 {
> +			compatible = "arm,pl330", "arm,primecell";
> +			reg = <0x0 0xff2c0000 0x0 0x4000>;
> +			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> +			#dma-cells = <1>;
> +			clocks = <&cru ACLK_DMAC0>;
> +			clock-names = "apb_pclk";
> +			peripherals-req-type-burst;

peripherals-req-type-burst is undocumented so likely some change to the
dma driver not yet upstream?

> +		};
> +
> +		dmac1: dma-controller@ff2d0000 {
> +			compatible = "arm,pl330", "arm,primecell";
> +			reg = <0x0 0xff2d0000 0x0 0x4000>;
> +			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> +			#dma-cells = <1>;
> +			clocks = <&cru ACLK_DMAC1>;
> +			clock-names = "apb_pclk";
> +			peripherals-req-type-burst;
> +		};
> +	};
> +
> +	i2s_2ch_0: i2s@ff350000 {
> +		compatible = "rockchip,rk3308-i2s", "rockchip,rk3066-i2s";
> +		reg = <0x0 0xff350000 0x0 0x1000>;
> +		interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
> +		clocks = <&cru SCLK_I2S0_2CH>, <&cru HCLK_I2S0_2CH>;
> +		clock-names = "i2s_clk", "i2s_hclk";
> +		dmas = <&dmac1 8>, <&dmac1 9>;
> +		dma-names = "tx", "rx";
> +		resets = <&cru SRST_I2S0_2CH_M>, <&cru SRST_I2S0_2CH_H>;
> +		reset-names = "reset-m", "reset-h";

These resets don't seem to be defined in driver or binding?
Same for other i2s

> +		pinctrl-names = "default";
> +		pinctrl-0 = <&i2s_2ch_0_sclk
> +			     &i2s_2ch_0_lrck
> +			     &i2s_2ch_0_sdi
> +			     &i2s_2ch_0_sdo>;
> +		status = "disabled";
> +	};


> +
> +	mac: ethernet@ff4e0000 {
> +		compatible = "rockchip,rk3308-mac";

Was this support to the network driver already submitted?
Because I wasn't able to find it in the gmac driver.

> +		reg = <0x0 0xff4e0000 0x0 0x10000>;
> +		rockchip,grf = <&grf>;
> +		interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
> +		interrupt-names = "macirq";
> +		clocks = <&cru SCLK_MAC>, <&cru SCLK_MAC_RX_TX>,
> +			 <&cru SCLK_MAC_RX_TX>, <&cru SCLK_MAC_REF>,
> +			 <&cru SCLK_MAC>, <&cru ACLK_MAC>,
> +			 <&cru PCLK_MAC>, <&cru SCLK_MAC_RMII>;
> +		clock-names = "stmmaceth", "mac_clk_rx",
> +			      "mac_clk_tx", "clk_mac_ref",
> +			      "clk_mac_refout", "aclk_mac",
> +			      "pclk_mac", "clk_mac_speed";
> +		phy-mode = "rmii";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&rmii_pins &mac_refclk_12ma>;
> +		resets = <&cru SRST_MAC_A>;
> +		reset-names = "stmmaceth";
> +		status = "disabled";
> +	};


Heiko