From: "Arend van Spriel" <arend@broadcom.com>
To: Balaji T K <balajitk@ti.com>
Cc: Roger Quadros <rogerq@ti.com>, Tony Lindgren <tony@atomide.com>,
linux-omap@vger.kernel.org,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
luca@coelho.fi
Subject: Re: using mmc2 on panda [was: Regression 3.11-rc1: omap4panda: no usb and consequently no ethernet]
Date: Wed, 2 Oct 2013 11:03:47 +0200 [thread overview]
Message-ID: <524BE173.1050407@broadcom.com> (raw)
In-Reply-To: <524ACBC6.5060208@ti.com>
On 10/01/2013 03:19 PM, Balaji T K wrote:
>>>>>> Hi Roger,
>>>>>>
>>>>>> It has been a while, but I would like to pickup this thread. We
>>>>>> have a couple of pandaboards used as test setup. These have an
>>>>>> SDIO adapter hooked up to expansion connector A using MMC2. I have
>>>>>> attached the patch file (just ignore platform_data stuff). Now on
>>>>>> one board it works, but not for the other. I suspect a board issue
>>>>>> so listing the two types that we use:
>>>>>>
>>>>>> PandaBoard rev A2 (dmesg: OMAP4430 ES2.1): works
>>>>>> PandaBoardES rev B1 (dmesg: OMAP4460 ES1.1): nope
>>>>>>
>>>>>> Any hints for me.
>>>>>
>>>>> Does your PandaboardES have the WLAN chip (U4) mounted? If yes, how
>>>>> do you isolate
>>>>> it from your external SDIO adapter?
>>>
>>> On my 4460 board in front of me U4 is not populated, but U3 is (the
>>> TiWi thing).
>>>
>>>>
>>>> OK, just realized that the expansion connector uses different pads
>>>> for MMC2. However, you still
>>>> need to make sure that the other pins (connected to on board WLAN
>>>> chip) are not muxed as MMC2.
>>>
>>> I think Luciano added DT patches for on-board WLAN and it uses MMC5
>>> if I am not mistaken(?). Attached are the dmesg logs of the two boards.
>>
>> Right. WLAN is supposed to use MMC5. But if you don't have Luca's
>> patches, can you please ensure that those pins are muxed either as
>> safe mode
>> or as MMC5? Default seems to be safe mode, but you should cross check.
>>
>> Also in your patches you have set mmc2-clk to PIN_INPUT_PULLUP
>> Shouldn't it be PIN_OUTPUT?
>>
>> Still I have no clue why it works on 4430 and not on 4460. Are you
>> using the same bootloader image on both boards?
>>
> if you are using vaux1, can you check the voltage levels,
>
> From dmesg you attached,
> vaux1 is set to 1.8V on omap4430 and to 2.8V on OMAP4460
>
> 4430
> [ 2.425750] VAUX1_6030: 1000 <--> 3000 mV at 1800 mV
>
> 4460
> [ 2.244262] VAUX1_6030: 1000 <--> 3000 mV at 2800 mV
Nice catch. Not sure whether this is an issue, but worth looking into.
> Can you also check with MMC_DEBUG enabled for any clues.
building....
>> cheers,
>> -roger
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
next prev parent reply other threads:[~2013-10-02 9:03 UTC|newest]
Thread overview: 44+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-07-18 8:41 Regression 3.11-rc1: omap4panda: no usb and consequently no ethernet Arend van Spriel
2013-07-18 8:59 ` Tony Lindgren
2013-07-18 10:18 ` Arend van Spriel
2013-07-19 10:36 ` Arend van Spriel
2013-07-19 10:49 ` Roger Quadros
2013-07-19 10:49 ` Roger Quadros
2013-07-19 10:57 ` Arend van Spriel
2013-10-01 8:05 ` using mmc2 on panda [was: Regression 3.11-rc1: omap4panda: no usb and consequently no ethernet] Arend van Spriel
2013-10-01 9:49 ` Roger Quadros
2013-10-01 9:49 ` Roger Quadros
2013-10-01 9:53 ` Roger Quadros
2013-10-01 9:53 ` Roger Quadros
2013-10-01 10:53 ` Arend van Spriel
2013-10-01 11:29 ` Luca Coelho
2013-10-02 10:20 ` Arend van Spriel
2013-10-02 10:48 ` Luca Coelho
2013-10-01 12:17 ` Roger Quadros
2013-10-01 12:17 ` Roger Quadros
2013-10-01 13:19 ` Balaji T K
2013-10-01 13:19 ` Balaji T K
2013-10-02 9:03 ` Arend van Spriel [this message]
2013-07-19 10:53 ` Regression 3.11-rc1: omap4panda: no usb and consequently no ethernet Tony Lindgren
2013-07-20 7:38 ` Luciano Coelho
2013-07-20 7:38 ` Luciano Coelho
2013-07-18 11:18 ` Roger Quadros
2013-07-18 11:18 ` Roger Quadros
2013-07-18 11:24 ` Arend van Spriel
2013-07-18 11:30 ` Roger Quadros
2013-07-18 11:30 ` Roger Quadros
2013-07-18 12:38 ` Arend van Spriel
2013-07-18 12:42 ` Roger Quadros
2013-07-18 12:42 ` Roger Quadros
2013-07-25 13:06 ` Arend van Spriel
2013-07-26 2:49 ` Joel Fernandes
2013-07-26 2:49 ` Joel Fernandes
2013-07-26 3:00 ` Joel Fernandes
2013-07-26 3:00 ` Joel Fernandes
2013-07-26 7:25 ` Arend van Spriel
2013-07-26 10:13 ` Arend van Spriel
2013-07-26 10:15 ` Arend van Spriel
2013-07-26 10:23 ` Arend van Spriel
2013-07-26 10:37 ` Roger Quadros
2013-07-26 10:37 ` Roger Quadros
2013-07-26 10:40 ` Arend van Spriel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=524BE173.1050407@broadcom.com \
--to=arend@broadcom.com \
--cc=balajitk@ti.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=luca@coelho.fi \
--cc=rogerq@ti.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.