All of lore.kernel.org
 help / color / mirror / Atom feed
* wakeonlan fails if pm-hibernate used
@ 2013-08-08 13:15 Ken Sharp
  2013-11-24  7:09 ` Ken Sharp
  0 siblings, 1 reply; 2+ messages in thread
From: Ken Sharp @ 2013-08-08 13:15 UTC (permalink / raw)
  To: linux-pm; +Cc: 1074110

wakeonlan fails if pm-hibernate used

After issuing halt -p, wakeonlan works fine. after issuing pm-hibernate, 
the machine will not wake up.

interfaces:
auto eth0
iface eth0 inet dhcp
up ethtool -s eth0 wol g
down ethtool -s eth0 wol g

Settings for eth0:
  Supported ports: [ TP MII ]
  Supported link modes: 10baseT/Half 10baseT/Full
                          100baseT/Half 100baseT/Full
  Supported pause frame use: No
  Supports auto-negotiation: Yes
  Advertised link modes: 10baseT/Half 10baseT/Full
                          100baseT/Half 100baseT/Full
  Advertised pause frame use: No
  Advertised auto-negotiation: Yes
  Link partner advertised link modes: 10baseT/Half 10baseT/Full
                                       100baseT/Half 100baseT/Full
  Link partner advertised pause frame use: Symmetric
  Link partner advertised auto-negotiation: Yes
  Speed: 100Mb/s
  Duplex: Full
  Port: MII
  PHYAD: 32
  Transceiver: internal
  Auto-negotiation: on
  Supports Wake-on: pumbg
  Wake-on: g
  Current message level: 0x00000007 (7)
           drv probe link
  Link detected: yes

01:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. 
RTL-8139/8139C/8139C+ (rev 10

Reported on Launchpad
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1074110

$ cat /proc/version
Linux version 3.11.0-999-generic (apw@gomeisa) (gcc version 4.6.3 
(Ubuntu/Linaro 4.6.3-1ubuntu5) ) #201308070514 SMP Wed Aug 7 09:24:40 
UTC 2013

$ lsb_release -rd
Description:	Ubuntu 12.04.2 LTS
Release:	12.04

$ ./ver_linux
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.

Linux oldhomeserver 3.11.0-999-generic #201308070514 SMP Wed Aug 7 
09:24:40 UTC 2013 i686 i686 i386 GNU/Linux

Gnu C                  4.6
Gnu make               3.81
binutils               2.22
util-linux             2.20.1
mount                  support
module-init-tools      3.16
e2fsprogs              1.42
pcmciautils            018
Linux C Library        2.15
Dynamic linker (ldd)   2.15
Procps                 3.2.8
Net-tools              1.60
Kbd                    1.15.2
Sh-utils               8.13
Modules Loaded         zram dm_crypt nfsd nfs_acl auth_rpcgss nfs 
fscache lockd binfmt_misc sunrpc gpio_ich lpc_ich serio_raw shpchp 
intel_rng mac_hid hwmon_vid lp parport 8139too 8139cp mii

$ cat /proc/cpuinfo
processor	: 0
vendor_id	: GenuineIntel
cpu family	: 6
model		: 8
model name	: Pentium III (Coppermine)
stepping	: 3
microcode	: 0x10
cpu MHz		: 734.956
cache size	: 256 KB
fdiv_bug	: no
f00f_bug	: no
coma_bug	: no
fpu		: yes
fpu_exception	: yes
cpuid level	: 2
wp		: yes
flags		: fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pse36 
mmx fxsr sse
bogomips	: 1469.91
clflush size	: 32
cache_alignment	: 32
address sizes	: 36 bits physical, 32 bits virtual
power management:

$ cat /proc/modules
zram 18166 1 - Live 0x00000000 (C)
dm_crypt 22524 0 - Live 0x00000000
nfsd 246709 13 - Live 0x00000000
nfs_acl 12771 1 nfsd, Live 0x00000000
auth_rpcgss 49253 1 nfsd, Live 0x00000000
nfs 162863 0 - Live 0x00000000
fscache 52016 1 nfs, Live 0x00000000
lockd 79198 2 nfsd,nfs, Live 0x00000000
binfmt_misc 17268 1 - Live 0x00000000
sunrpc 236600 23 nfsd,nfs_acl,auth_rpcgss,nfs,lockd, Live 0x00000000
gpio_ich 13278 0 - Live 0x00000000
lpc_ich 16987 0 - Live 0x00000000
serio_raw 13189 0 - Live 0x00000000
shpchp 32265 0 - Live 0x00000000
intel_rng 12700 0 - Live 0x00000000
mac_hid 13077 0 - Live 0x00000000
hwmon_vid 12723 0 - Live 0x00000000
lp 13359 0 - Live 0x00000000
parport 40930 1 lp, Live 0x00000000
8139too 32770 0 - Live 0x00000000
8139cp 27168 0 - Live 0x00000000
mii 13693 2 8139too,8139cp, Live 0x00000000

$ cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-0060 : keyboard
0064-0064 : keyboard
0070-0071 : rtc0
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : 0000:00:1f.1
   0170-0177 : ata_piix
01f0-01f7 : 0000:00:1f.1
   01f0-01f7 : ata_piix
0376-0376 : 0000:00:1f.1
   0376-0376 : ata_piix
03c0-03df : vga+
03f6-03f6 : 0000:00:1f.1
   03f6-03f6 : ata_piix
0400-0403 : ACPI PM1a_EVT_BLK
0404-0405 : ACPI PM1a_CNT_BLK
0408-040b : ACPI PM_TMR
0410-0415 : ACPI CPU throttle
0428-042b : ACPI GPE0_BLK
042c-042f : ACPI GPE1_BLK
0430-0433 : iTCO_wdt
0460-047f : iTCO_wdt
0480-04bf : gpio_ich
   0480-04bf : 0000:00:1f.0
04c0-04cf : 0000:00:1f.3
0cf8-0cff : PCI conf1
c000-cfff : PCI Bus 0000:01
   cc00-ccff : 0000:01:03.0
     cc00-ccff : 8139too
de00-de1f : 0000:00:1f.2
   de00-de1f : uhci_hcd
ff00-ff0f : 0000:00:1f.1
   ff00-ff0f : ata_piix

$ cat /proc/iomem
00000000-00000fff : reserved
00001000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000e0000-000fffff : reserved
   000f0000-000fffff : System ROM
00100000-0beeffff : System RAM
   01000000-016680a2 : Kernel code
   016680a3-019bd17f : Kernel data
   01aa1000-01b94fff : Kernel bss
0bef0000-0bef7fff : ACPI Tables
0bef8000-0befffff : ACPI Non-volatile Storage
0bf00000-0bffffff : reserved
dfc00000-dfcfffff : PCI Bus 0000:01
e0000000-e3ffffff : 0000:00:01.0
e7e00000-ebefffff : PCI Bus 0000:01
   e8000000-e80000ff : 0000:01:03.0
     e8000000-e80000ff : 8139too
ee000000-ee07ffff : 0000:00:01.0
fff80000-ffffffff : reserved

$ sudo lspci -vvv
00:00.0 Host bridge: Intel Corporation 82810E DC-133 (GMCH) Graphics 
Memory Controller Hub (rev 03)
	Subsystem: Intel Corporation 82810E DC-133 (GMCH) Graphics Memory 
Controller Hub
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Kernel driver in use: agpgart-intel

00:01.0 VGA compatible controller: Intel Corporation 82810E DC-133 (CGC) 
Chipset Graphics Controller (rev 03) (prog-if 00 [VGA controller])
	Subsystem: Giga-byte Technology Device 0200
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
	Region 1: Memory at ee000000 (32-bit, non-prefetchable) [size=512K]
	Expansion ROM at <unassigned> [disabled]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

00:1e.0 PCI bridge: Intel Corporation 82801AA PCI Bridge (rev 02) 
(prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
	I/O behind bridge: 0000c000-0000cfff
	Memory behind bridge: e7e00000-ebefffff
	Prefetchable memory behind bridge: dfc00000-dfcfffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Kernel modules: shpchp

00:1f.0 ISA bridge: Intel Corporation 82801AA ISA Bridge (LPC) (rev 02)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Kernel driver in use: lpc_ich
	Kernel modules: lpc_ich, intel-rng

00:1f.1 IDE interface: Intel Corporation 82801AA IDE Controller (rev 02) 
(prog-if 80 [Master])
	Subsystem: Intel Corporation 82801AA IDE Controller
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
	Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
	Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
	Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
	Region 4: I/O ports at ff00 [size=16]
	Kernel driver in use: ata_piix

00:1f.2 USB controller: Intel Corporation 82801AA USB Controller (rev 
02) (prog-if 00 [UHCI])
	Subsystem: Intel Corporation 82801AA USB Controller
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin D routed to IRQ 10
	Region 4: I/O ports at de00 [size=32]
	Kernel driver in use: uhci_hcd

00:1f.3 SMBus: Intel Corporation 82801AA SMBus Controller (rev 02)
	Subsystem: Intel Corporation 82801AA SMBus Controller
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin B routed to IRQ 0
	Region 4: I/O ports at 04c0 [size=16]
	Kernel modules: i2c-i801

01:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. 
RTL-8139/8139C/8139C+ (rev 10)
	Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (8000ns min, 16000ns max)
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at cc00 [size=256]
	Region 1: Memory at e8000000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA 
PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: 8139too
	Kernel modules: 8139too, 8139cp

$ cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 01 Lun: 00
   Vendor: ATA      Model: QUANTUM FIREBALL Rev: A01.
   Type:   Direct-Access                    ANSI  SCSI revision: 05
Host: scsi1 Channel: 00 Id: 00 Lun: 00
   Vendor: GoldStar Model: CD-RW CED-8080B  Rev: 1.02
   Type:   CD-ROM

$ ls /proc
1     1026  1406  1471  16    19   25   42   6    695  9 
cpuinfo      fs          kpagecount     mounts        slabinfo       tty
10    11    1461  1472  1641  2    26   44   619  7    986        crypto 
       interrupts  kpageflags     mtrr          softirqs       uptime
1005  1110  1462  1473  1642  20   27   45   64   709  991 
devices      iomem       latency_stats  net           stat           version
1006  12    1463  1477  17    21   28   467  65   731  acpi 
diskstats    ioports     loadavg        pagetypeinfo  swaps 
vmallocinfo
1008  13    1466  1499  18    22   3    468  654  793  buddyinfo  dma 
        irq         locks          partitions    sys            vmstat
1013  1373  1467  15    1844  224  324  5    657  797  bus        driver 
       kallsyms    mdstat         sched_debug   sysrq-trigger  zoneinfo
1014  14    1468  1515  1859  225  326  579  666  8    cgroups 
execdomains  kcore       meminfo        schedstat     sysvipc
1021  1401  1469  1535  1867  23   39   584  67   856  cmdline    fb 
        key-users   misc           scsi          timer_list
1023  1405  1470  1541  1868  24   41   586  694  895  consoles 
filesystems  kmsg        modules        self          timer_stats

$ sudo ethtool eth0
Settings for eth0:
	Supported ports: [ TP MII ]
	Supported link modes:   10baseT/Half 10baseT/Full
	                        100baseT/Half 100baseT/Full
	Supported pause frame use: No
	Supports auto-negotiation: Yes
	Advertised link modes:  10baseT/Half 10baseT/Full
	                        100baseT/Half 100baseT/Full
	Advertised pause frame use: No
	Advertised auto-negotiation: Yes
	Link partner advertised link modes:  10baseT/Half 10baseT/Full
	                                     100baseT/Half 100baseT/Full
	Link partner advertised pause frame use: Symmetric
	Link partner advertised auto-negotiation: Yes
	Speed: 100Mb/s
	Duplex: Full
	Port: MII
	PHYAD: 32
	Transceiver: internal
	Auto-negotiation: on
	Supports Wake-on: pumbg
	Wake-on: g
	Current message level: 0x00000007 (7)
			       drv probe link
	Link detected: yes

Taken as a guide to report this: 
https://wiki.ubuntu.com/Bugs/Upstream/kernel

Apologies if this is too much or not enough information, this is the 
first time I have attempted to report a problem with the kernel.

I looked through https://www.kernel.org/doc/Documentation/power/ but the 
processes either didn't seem relevant or I simply didn't understand. If 
you need me to run through the processes then please let me know.

Specifically 
https://www.kernel.org/doc/Documentation/power/basic-pm-debugging.txt 
suggests that the debugging would test the wake/resume cycle, which I 
don't think is relevant in this case. But I could be wrong!

Thanks for your help,

Ken

^ permalink raw reply	[flat|nested] 2+ messages in thread
end of thread, other threads:[~2013-11-24  7:09 UTC | newest]

Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2013-08-08 13:15 wakeonlan fails if pm-hibernate used Ken Sharp
2013-11-24  7:09 ` Ken Sharp

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.