[PATCH 0/4] input: Add new sun4i-lradc-keys driver

[PATCH 0/4] input: Add new sun4i-lradc-keys driver

[Hans de Goede]

Hi Dimitri,

Here is another input driver for Allwinner sunxi SoCs. As with the touchscreen
driver the dts files are posted here for completeness and will be merged
through Maxime's tree.

Please review and if everything is ok, add this to your tree for Linus.

Thanks & Regards,

Hans

[PATCH 0/4] input: Add new sun4i-lradc-keys driver

[Hans de Goede]

Hi Dimitri,

Here is another input driver for Allwinner sunxi SoCs. As with the touchscreen
driver the dts files are posted here for completeness and will be merged
through Maxime's tree.

Please review and if everything is ok, add this to your tree for Linus.

Thanks & Regards,

Hans

[PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Hans de Goede]

Allwinnner sunxi SoCs have a low resolution adc (called lradc) which is
specifically designed to have various (tablet) keys (ie home, back, search,
etc). attached to it using a resistor network. This adds a driver for this.

There are 2 channels, currently this driver only supports chan0 since there
are no boards known to use chan1. The devicetree properties are already
prefixed with chan0 as preparation for chan1 support in the future.

This has been tested on an olimex a10s-olinuxino-micro, a13-olinuxino, and
a20-olinuxino-micro.

Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
---
 .../devicetree/bindings/input/sun4i-lradc-keys.txt |  20 ++
 drivers/input/keyboard/Kconfig                     |  10 +
 drivers/input/keyboard/Makefile                    |   1 +
 drivers/input/keyboard/sun4i-lradc-keys.c          | 243 +++++++++++++++++++++
 4 files changed, 274 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt
 create mode 100644 drivers/input/keyboard/sun4i-lradc-keys.c

diff --git a/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt
new file mode 100644
index 0000000..94960da
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt
@@ -0,0 +1,20 @@
+Allwinner sun4i low res adc attached tablet keys
+------------------------------------------------
+
+Required properties:
+ - compatible: "allwinner,sun4i-lradc-keys"
+ - reg: mmio address range of the chip
+ - interrupts: interrupt to which the chip is connected
+ - allwinner,chan0-step: step in mV between keys must be 150 or 200
+ - allwinner,chan0-keycodes: array of include/uapi/linux/input.h KEY_ codes
+
+Example:
+
+	lradc: lradc@01c22800 {
+		compatible = "allwinner,sun4i-lradc-keys";
+		reg = <0x01c22800 0x100>;
+		interrupts = <31>;
+		allwinner,chan0-step = <200>;
+		/* KEY_VOLUMEUP VOLUMEDOWN MENU ENTER HOME */
+		allwinner,chan0-keycodes = <115 114 139 28 102>;
+	};
diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
index bb174c1..d95e6e4 100644
--- a/drivers/input/keyboard/Kconfig
+++ b/drivers/input/keyboard/Kconfig
@@ -544,6 +544,16 @@ config KEYBOARD_STMPE
 	  To compile this driver as a module, choose M here: the module will be
 	  called stmpe-keypad.
 
+config KEYBOARD_SUN4I_LRADC
+	tristate "Allwinner sun4i low res adc attached tablet keys support"
+	depends on ARCH_SUNXI
+	help
+	  This selects support for the Allwinner low res adc attached tablet
+	  keys found on Allwinner sunxi SoCs.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called sun4i-lradc-keys.
+
 config KEYBOARD_DAVINCI
 	tristate "TI DaVinci Key Scan"
 	depends on ARCH_DAVINCI_DM365
diff --git a/drivers/input/keyboard/Makefile b/drivers/input/keyboard/Makefile
index a699b61..f3265bd 100644
--- a/drivers/input/keyboard/Makefile
+++ b/drivers/input/keyboard/Makefile
@@ -50,6 +50,7 @@ obj-$(CONFIG_KEYBOARD_SH_KEYSC)		+= sh_keysc.o
 obj-$(CONFIG_KEYBOARD_SPEAR)		+= spear-keyboard.o
 obj-$(CONFIG_KEYBOARD_STMPE)		+= stmpe-keypad.o
 obj-$(CONFIG_KEYBOARD_STOWAWAY)		+= stowaway.o
+obj-$(CONFIG_KEYBOARD_SUN4I_LRADC)	+= sun4i-lradc-keys.o
 obj-$(CONFIG_KEYBOARD_SUNKBD)		+= sunkbd.o
 obj-$(CONFIG_KEYBOARD_TC3589X)		+= tc3589x-keypad.o
 obj-$(CONFIG_KEYBOARD_TEGRA)		+= tegra-kbc.o
diff --git a/drivers/input/keyboard/sun4i-lradc-keys.c b/drivers/input/keyboard/sun4i-lradc-keys.c
new file mode 100644
index 0000000..9ef4d10
--- /dev/null
+++ b/drivers/input/keyboard/sun4i-lradc-keys.c
@@ -0,0 +1,243 @@
+/*
+ * Allwinner sun4i low res adc attached tablet keys driver
+ *
+ * Copyright (C) 2014 Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * Allwinnner sunxi SoCs have a lradc which is specifically designed to have
+ * various (tablet) keys (ie home, back, search, etc). attached to it using
+ * a resistor network. This driver is for the keys on such boards.
+ *
+ * There are 2 channels, currently this driver only supports chan0 since there
+ * are no boards known to use chan1. The devicetree properties are already
+ * prefixed with chan0 as preparation for chan1 support in the future.
+ */
+
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#define LRADC_CTRL		0x00
+#define LRADC_INTC		0x04
+#define LRADC_INTS		0x08
+#define LRADC_DATA0		0x0c
+#define LRADC_DATA1		0x10
+
+/* LRADC_CTRL bits */
+#define FIRST_CONVERT_DLY(x)	((x) << 24) /* 8 bits */
+#define CHAN_SELECT(x)		((x) << 22) /* 2 bits */
+#define CONTINUE_TIME_SEL(x)	((x) << 16) /* 4 bits */
+#define KEY_MODE_SEL(x)		((x) << 12) /* 2 bits */
+#define LEVELA_B_CNT(x)		((x) << 8)  /* 4 bits */
+#define HOLD_EN(x)		((x) << 6)
+#define LEVELB_VOL(x)		((x) << 4)  /* 2 bits */
+#define SAMPLE_RATE(x)		((x) << 2)  /* 2 bits */
+#define ENABLE(x)		((x) << 0)
+
+/* LRADC_INTC and LRADC_INTS bits */
+#define CHAN1_KEYUP_IRQ		BIT(12)
+#define CHAN1_ALRDY_HOLD_IRQ	BIT(11)
+#define CHAN1_HOLD_IRQ		BIT(10)
+#define	CHAN1_KEYDOWN_IRQ	BIT(9)
+#define CHAN1_DATA_IRQ		BIT(8)
+#define CHAN0_KEYUP_IRQ		BIT(4)
+#define CHAN0_ALRDY_HOLD_IRQ	BIT(3)
+#define CHAN0_HOLD_IRQ		BIT(2)
+#define	CHAN0_KEYDOWN_IRQ	BIT(1)
+#define CHAN0_DATA_IRQ		BIT(0)
+
+#define MAX_KEYS		13
+
+/* Lookup table to map the adc val to a keycode index for 150 mv step size */
+static const u8 adc_val_to_key_index_step150[64] = {
+	0, 0, 0,
+	1, 1, 1, 1, 1,
+	2, 2, 2, 2, 2,
+	3, 3, 3, 3,
+	4, 4, 4, 4, 4,
+	5, 5, 5, 5, 5,
+	6, 6, 6, 6, 6,
+	7, 7, 7, 7,
+	8, 8, 8, 8, 8,
+	9, 9, 9, 9, 9,
+	10, 10, 10, 10,
+	11, 11, 11, 11,
+	12, 12, 12, 12, 12, 12, 12, 12, 12, 12
+};
+
+/* Lookup table to map the adc val to a keycode index for 200 mv step size */
+static const u8 adc_val_to_key_index_step200[64] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	1, 1, 1, 1, 1, 1, 1,
+	2, 2, 2, 2, 2, 2, 2,
+	3, 3, 3, 3, 3, 3,
+	4, 4, 4, 4, 4, 4,
+	5, 5, 5, 5, 5, 5,
+	6, 6, 6, 6, 6, 6, 6, 6, 6, 6,
+	7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7
+};
+
+struct sun4i_lradc_data {
+	struct device *dev;
+	struct input_dev *input;
+	void __iomem *base;
+	u32 chan0_step;
+	u32 chan0_keycode;
+	u32 chan0_keycodes[MAX_KEYS];
+};
+
+static irqreturn_t sun4i_lradc_irq(int irq, void *dev_id)
+{
+	struct sun4i_lradc_data *lradc = dev_id;
+	u32 ints, val;
+
+	ints  = readl(lradc->base + LRADC_INTS);
+
+	/*
+	 * lradc supports only one keypress at a time, release does not give
+	 * any info as to which key was released, so we cache the keycode.
+	 */
+	if ((ints & CHAN0_KEYDOWN_IRQ) && lradc->chan0_keycode == 0) {
+		val = readl(lradc->base + LRADC_DATA0);
+		if (lradc->chan0_step == 150)
+			val = adc_val_to_key_index_step150[val];
+		else
+			val = adc_val_to_key_index_step200[val];
+
+		lradc->chan0_keycode = lradc->chan0_keycodes[val];
+		input_report_key(lradc->input, lradc->chan0_keycode, 1);
+	}
+
+	if (ints & CHAN0_KEYUP_IRQ) {
+		input_report_key(lradc->input, lradc->chan0_keycode, 0);
+		lradc->chan0_keycode = 0;
+	}
+
+	input_sync(lradc->input);
+
+	writel(ints, lradc->base + LRADC_INTS);
+
+	return IRQ_HANDLED;
+}
+
+static int sun4i_lradc_open(struct input_dev *dev)
+{
+	struct sun4i_lradc_data *lradc = input_get_drvdata(dev);
+
+	/*
+	 * Set sample time to 16 ms / 62.5 Hz. Wait 2 * 16 ms for key to
+	 * stabilize on press, wait (1 + 1) * 16 ms for key release
+	 */
+	writel(FIRST_CONVERT_DLY(2) | LEVELA_B_CNT(1) | HOLD_EN(1) |
+		SAMPLE_RATE(2) | ENABLE(1), lradc->base + LRADC_CTRL);
+
+	writel(CHAN0_KEYUP_IRQ | CHAN0_KEYDOWN_IRQ, lradc->base + LRADC_INTC);
+
+	return 0;
+}
+
+static void sun4i_lradc_close(struct input_dev *dev)
+{
+	struct sun4i_lradc_data *lradc = input_get_drvdata(dev);
+
+	/* Disable lradc, leave other settings unchanged */
+	writel(FIRST_CONVERT_DLY(2) | LEVELA_B_CNT(1) | HOLD_EN(1) |
+		SAMPLE_RATE(2), lradc->base + LRADC_CTRL);
+	writel(0, lradc->base + LRADC_INTC);
+}
+
+static int sun4i_lradc_probe(struct platform_device *pdev)
+{
+	struct sun4i_lradc_data *lradc;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	int i, ret;
+
+	lradc = devm_kzalloc(dev, sizeof(struct sun4i_lradc_data), GFP_KERNEL);
+	if (!lradc)
+		return -ENOMEM;
+
+	ret = of_property_read_u32(np, "allwinner,chan0-step",
+				   &lradc->chan0_step);
+	if (ret || (lradc->chan0_step != 150 && lradc->chan0_step != 200)) {
+		dev_err(dev, "Invalid allwinner,chan0-step dt-property\n");
+		return -EINVAL;
+	}
+
+	for (i = 0; i < MAX_KEYS; i++)
+		of_property_read_u32_index(np, "allwinner,chan0-keycodes",
+					   i, &lradc->chan0_keycodes[i]);
+
+	lradc->dev = dev;
+	lradc->input = devm_input_allocate_device(dev);
+	if (!lradc->input)
+		return -ENOMEM;
+
+	lradc->input->name = pdev->name;
+	lradc->input->phys = "sun4i_lradc/input0";
+	lradc->input->open = sun4i_lradc_open;
+	lradc->input->close = sun4i_lradc_close;
+	lradc->input->id.bustype = BUS_HOST;
+	lradc->input->id.vendor = 0x0001;
+	lradc->input->id.product = 0x0001;
+	lradc->input->id.version = 0x0100;
+	lradc->input->evbit[0] =  BIT(EV_SYN) | BIT(EV_KEY);
+	for (i = 0; i < MAX_KEYS; i++)
+		set_bit(lradc->chan0_keycodes[i], lradc->input->keybit);
+	input_set_drvdata(lradc->input, lradc);
+
+	lradc->base = devm_ioremap_resource(dev,
+			      platform_get_resource(pdev, IORESOURCE_MEM, 0));
+	if (IS_ERR(lradc->base))
+		return PTR_ERR(lradc->base);
+
+	ret = devm_request_irq(dev, platform_get_irq(pdev, 0), sun4i_lradc_irq,
+			       0, "sun4i-lradc-keys", lradc);
+	if (ret)
+		return ret;
+
+	ret = input_register_device(lradc->input);
+	if (ret)
+		return ret;
+
+	platform_set_drvdata(pdev, lradc);
+	return 0;
+}
+
+static const struct of_device_id sun4i_lradc_of_match[] = {
+	{ .compatible = "allwinner,sun4i-lradc-keys", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, sun4i_lradc_of_match);
+
+static struct platform_driver sun4i_lradc_driver = {
+	.driver = {
+		.owner	= THIS_MODULE,
+		.name	= "sun4i-lradc-keys",
+		.of_match_table = of_match_ptr(sun4i_lradc_of_match),
+	},
+	.probe	= sun4i_lradc_probe,
+};
+
+module_platform_driver(sun4i_lradc_driver);
+
+MODULE_DESCRIPTION("Allwinner sun4i low res adc attached tablet keys driver");
+MODULE_AUTHOR("Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>");
+MODULE_LICENSE("GPL");
-- 
1.8.4.2

[PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Hans de Goede]

Allwinnner sunxi SoCs have a low resolution adc (called lradc) which is
specifically designed to have various (tablet) keys (ie home, back, search,
etc). attached to it using a resistor network. This adds a driver for this.

There are 2 channels, currently this driver only supports chan0 since there
are no boards known to use chan1. The devicetree properties are already
prefixed with chan0 as preparation for chan1 support in the future.

This has been tested on an olimex a10s-olinuxino-micro, a13-olinuxino, and
a20-olinuxino-micro.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 .../devicetree/bindings/input/sun4i-lradc-keys.txt |  20 ++
 drivers/input/keyboard/Kconfig                     |  10 +
 drivers/input/keyboard/Makefile                    |   1 +
 drivers/input/keyboard/sun4i-lradc-keys.c          | 243 +++++++++++++++++++++
 4 files changed, 274 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt
 create mode 100644 drivers/input/keyboard/sun4i-lradc-keys.c

diff --git a/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt
new file mode 100644
index 0000000..94960da
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt
@@ -0,0 +1,20 @@
+Allwinner sun4i low res adc attached tablet keys
+------------------------------------------------
+
+Required properties:
+ - compatible: "allwinner,sun4i-lradc-keys"
+ - reg: mmio address range of the chip
+ - interrupts: interrupt to which the chip is connected
+ - allwinner,chan0-step: step in mV between keys must be 150 or 200
+ - allwinner,chan0-keycodes: array of include/uapi/linux/input.h KEY_ codes
+
+Example:
+
+	lradc: lradc at 01c22800 {
+		compatible = "allwinner,sun4i-lradc-keys";
+		reg = <0x01c22800 0x100>;
+		interrupts = <31>;
+		allwinner,chan0-step = <200>;
+		/* KEY_VOLUMEUP VOLUMEDOWN MENU ENTER HOME */
+		allwinner,chan0-keycodes = <115 114 139 28 102>;
+	};
diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
index bb174c1..d95e6e4 100644
--- a/drivers/input/keyboard/Kconfig
+++ b/drivers/input/keyboard/Kconfig
@@ -544,6 +544,16 @@ config KEYBOARD_STMPE
 	  To compile this driver as a module, choose M here: the module will be
 	  called stmpe-keypad.
 
+config KEYBOARD_SUN4I_LRADC
+	tristate "Allwinner sun4i low res adc attached tablet keys support"
+	depends on ARCH_SUNXI
+	help
+	  This selects support for the Allwinner low res adc attached tablet
+	  keys found on Allwinner sunxi SoCs.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called sun4i-lradc-keys.
+
 config KEYBOARD_DAVINCI
 	tristate "TI DaVinci Key Scan"
 	depends on ARCH_DAVINCI_DM365
diff --git a/drivers/input/keyboard/Makefile b/drivers/input/keyboard/Makefile
index a699b61..f3265bd 100644
--- a/drivers/input/keyboard/Makefile
+++ b/drivers/input/keyboard/Makefile
@@ -50,6 +50,7 @@ obj-$(CONFIG_KEYBOARD_SH_KEYSC)		+= sh_keysc.o
 obj-$(CONFIG_KEYBOARD_SPEAR)		+= spear-keyboard.o
 obj-$(CONFIG_KEYBOARD_STMPE)		+= stmpe-keypad.o
 obj-$(CONFIG_KEYBOARD_STOWAWAY)		+= stowaway.o
+obj-$(CONFIG_KEYBOARD_SUN4I_LRADC)	+= sun4i-lradc-keys.o
 obj-$(CONFIG_KEYBOARD_SUNKBD)		+= sunkbd.o
 obj-$(CONFIG_KEYBOARD_TC3589X)		+= tc3589x-keypad.o
 obj-$(CONFIG_KEYBOARD_TEGRA)		+= tegra-kbc.o
diff --git a/drivers/input/keyboard/sun4i-lradc-keys.c b/drivers/input/keyboard/sun4i-lradc-keys.c
new file mode 100644
index 0000000..9ef4d10
--- /dev/null
+++ b/drivers/input/keyboard/sun4i-lradc-keys.c
@@ -0,0 +1,243 @@
+/*
+ * Allwinner sun4i low res adc attached tablet keys driver
+ *
+ * Copyright (C) 2014 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * Allwinnner sunxi SoCs have a lradc which is specifically designed to have
+ * various (tablet) keys (ie home, back, search, etc). attached to it using
+ * a resistor network. This driver is for the keys on such boards.
+ *
+ * There are 2 channels, currently this driver only supports chan0 since there
+ * are no boards known to use chan1. The devicetree properties are already
+ * prefixed with chan0 as preparation for chan1 support in the future.
+ */
+
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#define LRADC_CTRL		0x00
+#define LRADC_INTC		0x04
+#define LRADC_INTS		0x08
+#define LRADC_DATA0		0x0c
+#define LRADC_DATA1		0x10
+
+/* LRADC_CTRL bits */
+#define FIRST_CONVERT_DLY(x)	((x) << 24) /* 8 bits */
+#define CHAN_SELECT(x)		((x) << 22) /* 2 bits */
+#define CONTINUE_TIME_SEL(x)	((x) << 16) /* 4 bits */
+#define KEY_MODE_SEL(x)		((x) << 12) /* 2 bits */
+#define LEVELA_B_CNT(x)		((x) << 8)  /* 4 bits */
+#define HOLD_EN(x)		((x) << 6)
+#define LEVELB_VOL(x)		((x) << 4)  /* 2 bits */
+#define SAMPLE_RATE(x)		((x) << 2)  /* 2 bits */
+#define ENABLE(x)		((x) << 0)
+
+/* LRADC_INTC and LRADC_INTS bits */
+#define CHAN1_KEYUP_IRQ		BIT(12)
+#define CHAN1_ALRDY_HOLD_IRQ	BIT(11)
+#define CHAN1_HOLD_IRQ		BIT(10)
+#define	CHAN1_KEYDOWN_IRQ	BIT(9)
+#define CHAN1_DATA_IRQ		BIT(8)
+#define CHAN0_KEYUP_IRQ		BIT(4)
+#define CHAN0_ALRDY_HOLD_IRQ	BIT(3)
+#define CHAN0_HOLD_IRQ		BIT(2)
+#define	CHAN0_KEYDOWN_IRQ	BIT(1)
+#define CHAN0_DATA_IRQ		BIT(0)
+
+#define MAX_KEYS		13
+
+/* Lookup table to map the adc val to a keycode index for 150 mv step size */
+static const u8 adc_val_to_key_index_step150[64] = {
+	0, 0, 0,
+	1, 1, 1, 1, 1,
+	2, 2, 2, 2, 2,
+	3, 3, 3, 3,
+	4, 4, 4, 4, 4,
+	5, 5, 5, 5, 5,
+	6, 6, 6, 6, 6,
+	7, 7, 7, 7,
+	8, 8, 8, 8, 8,
+	9, 9, 9, 9, 9,
+	10, 10, 10, 10,
+	11, 11, 11, 11,
+	12, 12, 12, 12, 12, 12, 12, 12, 12, 12
+};
+
+/* Lookup table to map the adc val to a keycode index for 200 mv step size */
+static const u8 adc_val_to_key_index_step200[64] = {
+	0, 0, 0, 0, 0, 0, 0, 0,
+	1, 1, 1, 1, 1, 1, 1,
+	2, 2, 2, 2, 2, 2, 2,
+	3, 3, 3, 3, 3, 3,
+	4, 4, 4, 4, 4, 4,
+	5, 5, 5, 5, 5, 5,
+	6, 6, 6, 6, 6, 6, 6, 6, 6, 6,
+	7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7
+};
+
+struct sun4i_lradc_data {
+	struct device *dev;
+	struct input_dev *input;
+	void __iomem *base;
+	u32 chan0_step;
+	u32 chan0_keycode;
+	u32 chan0_keycodes[MAX_KEYS];
+};
+
+static irqreturn_t sun4i_lradc_irq(int irq, void *dev_id)
+{
+	struct sun4i_lradc_data *lradc = dev_id;
+	u32 ints, val;
+
+	ints  = readl(lradc->base + LRADC_INTS);
+
+	/*
+	 * lradc supports only one keypress at a time, release does not give
+	 * any info as to which key was released, so we cache the keycode.
+	 */
+	if ((ints & CHAN0_KEYDOWN_IRQ) && lradc->chan0_keycode == 0) {
+		val = readl(lradc->base + LRADC_DATA0);
+		if (lradc->chan0_step == 150)
+			val = adc_val_to_key_index_step150[val];
+		else
+			val = adc_val_to_key_index_step200[val];
+
+		lradc->chan0_keycode = lradc->chan0_keycodes[val];
+		input_report_key(lradc->input, lradc->chan0_keycode, 1);
+	}
+
+	if (ints & CHAN0_KEYUP_IRQ) {
+		input_report_key(lradc->input, lradc->chan0_keycode, 0);
+		lradc->chan0_keycode = 0;
+	}
+
+	input_sync(lradc->input);
+
+	writel(ints, lradc->base + LRADC_INTS);
+
+	return IRQ_HANDLED;
+}
+
+static int sun4i_lradc_open(struct input_dev *dev)
+{
+	struct sun4i_lradc_data *lradc = input_get_drvdata(dev);
+
+	/*
+	 * Set sample time to 16 ms / 62.5 Hz. Wait 2 * 16 ms for key to
+	 * stabilize on press, wait (1 + 1) * 16 ms for key release
+	 */
+	writel(FIRST_CONVERT_DLY(2) | LEVELA_B_CNT(1) | HOLD_EN(1) |
+		SAMPLE_RATE(2) | ENABLE(1), lradc->base + LRADC_CTRL);
+
+	writel(CHAN0_KEYUP_IRQ | CHAN0_KEYDOWN_IRQ, lradc->base + LRADC_INTC);
+
+	return 0;
+}
+
+static void sun4i_lradc_close(struct input_dev *dev)
+{
+	struct sun4i_lradc_data *lradc = input_get_drvdata(dev);
+
+	/* Disable lradc, leave other settings unchanged */
+	writel(FIRST_CONVERT_DLY(2) | LEVELA_B_CNT(1) | HOLD_EN(1) |
+		SAMPLE_RATE(2), lradc->base + LRADC_CTRL);
+	writel(0, lradc->base + LRADC_INTC);
+}
+
+static int sun4i_lradc_probe(struct platform_device *pdev)
+{
+	struct sun4i_lradc_data *lradc;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	int i, ret;
+
+	lradc = devm_kzalloc(dev, sizeof(struct sun4i_lradc_data), GFP_KERNEL);
+	if (!lradc)
+		return -ENOMEM;
+
+	ret = of_property_read_u32(np, "allwinner,chan0-step",
+				   &lradc->chan0_step);
+	if (ret || (lradc->chan0_step != 150 && lradc->chan0_step != 200)) {
+		dev_err(dev, "Invalid allwinner,chan0-step dt-property\n");
+		return -EINVAL;
+	}
+
+	for (i = 0; i < MAX_KEYS; i++)
+		of_property_read_u32_index(np, "allwinner,chan0-keycodes",
+					   i, &lradc->chan0_keycodes[i]);
+
+	lradc->dev = dev;
+	lradc->input = devm_input_allocate_device(dev);
+	if (!lradc->input)
+		return -ENOMEM;
+
+	lradc->input->name = pdev->name;
+	lradc->input->phys = "sun4i_lradc/input0";
+	lradc->input->open = sun4i_lradc_open;
+	lradc->input->close = sun4i_lradc_close;
+	lradc->input->id.bustype = BUS_HOST;
+	lradc->input->id.vendor = 0x0001;
+	lradc->input->id.product = 0x0001;
+	lradc->input->id.version = 0x0100;
+	lradc->input->evbit[0] =  BIT(EV_SYN) | BIT(EV_KEY);
+	for (i = 0; i < MAX_KEYS; i++)
+		set_bit(lradc->chan0_keycodes[i], lradc->input->keybit);
+	input_set_drvdata(lradc->input, lradc);
+
+	lradc->base = devm_ioremap_resource(dev,
+			      platform_get_resource(pdev, IORESOURCE_MEM, 0));
+	if (IS_ERR(lradc->base))
+		return PTR_ERR(lradc->base);
+
+	ret = devm_request_irq(dev, platform_get_irq(pdev, 0), sun4i_lradc_irq,
+			       0, "sun4i-lradc-keys", lradc);
+	if (ret)
+		return ret;
+
+	ret = input_register_device(lradc->input);
+	if (ret)
+		return ret;
+
+	platform_set_drvdata(pdev, lradc);
+	return 0;
+}
+
+static const struct of_device_id sun4i_lradc_of_match[] = {
+	{ .compatible = "allwinner,sun4i-lradc-keys", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, sun4i_lradc_of_match);
+
+static struct platform_driver sun4i_lradc_driver = {
+	.driver = {
+		.owner	= THIS_MODULE,
+		.name	= "sun4i-lradc-keys",
+		.of_match_table = of_match_ptr(sun4i_lradc_of_match),
+	},
+	.probe	= sun4i_lradc_probe,
+};
+
+module_platform_driver(sun4i_lradc_driver);
+
+MODULE_DESCRIPTION("Allwinner sun4i low res adc attached tablet keys driver");
+MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
+MODULE_LICENSE("GPL");
-- 
1.8.4.2

Re: [PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Dmitry Torokhov]

Hi Hans,

On Wed, Jan 01, 2014 at 08:30:07PM +0100, Hans de Goede wrote:
> +Required properties:
> + - compatible: "allwinner,sun4i-lradc-keys"
> + - reg: mmio address range of the chip
> + - interrupts: interrupt to which the chip is connected
> + - allwinner,chan0-step: step in mV between keys must be 150 or 200
> + - allwinner,chan0-keycodes: array of include/uapi/linux/input.h KEY_ codes

I think this should be "linux,chan0-keycodes".

Thanks.

-- 
Dmitry

[PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Dmitry Torokhov]

Hi Hans,

On Wed, Jan 01, 2014 at 08:30:07PM +0100, Hans de Goede wrote:
> +Required properties:
> + - compatible: "allwinner,sun4i-lradc-keys"
> + - reg: mmio address range of the chip
> + - interrupts: interrupt to which the chip is connected
> + - allwinner,chan0-step: step in mV between keys must be 150 or 200
> + - allwinner,chan0-keycodes: array of include/uapi/linux/input.h KEY_ codes

I think this should be "linux,chan0-keycodes".

Thanks.

-- 
Dmitry

Re: [PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Hans de Goede]

Hi,

On 01/01/2014 09:56 PM, Dmitry Torokhov wrote:
> Hi Hans,
>
> On Wed, Jan 01, 2014 at 08:30:07PM +0100, Hans de Goede wrote:
>> +Required properties:
>> + - compatible: "allwinner,sun4i-lradc-keys"
>> + - reg: mmio address range of the chip
>> + - interrupts: interrupt to which the chip is connected
>> + - allwinner,chan0-step: step in mV between keys must be 150 or 200
>> + - allwinner,chan0-keycodes: array of include/uapi/linux/input.h KEY_ codes
>
> I think this should be "linux,chan0-keycodes".

Right, because the codes are Linux specific, will fix in v2.

Regards,

Hans

[PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Hans de Goede]

Hi,

On 01/01/2014 09:56 PM, Dmitry Torokhov wrote:
> Hi Hans,
>
> On Wed, Jan 01, 2014 at 08:30:07PM +0100, Hans de Goede wrote:
>> +Required properties:
>> + - compatible: "allwinner,sun4i-lradc-keys"
>> + - reg: mmio address range of the chip
>> + - interrupts: interrupt to which the chip is connected
>> + - allwinner,chan0-step: step in mV between keys must be 150 or 200
>> + - allwinner,chan0-keycodes: array of include/uapi/linux/input.h KEY_ codes
>
> I think this should be "linux,chan0-keycodes".

Right, because the codes are Linux specific, will fix in v2.

Regards,

Hans

Re: [PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Heiko Stübner]

Hi Hans, Dmitry,

Am Donnerstag, 2. Januar 2014, 10:37:47 schrieb Hans de Goede:
> Hi,
> 
> On 01/01/2014 09:56 PM, Dmitry Torokhov wrote:
> > Hi Hans,
> > 
> > On Wed, Jan 01, 2014 at 08:30:07PM +0100, Hans de Goede wrote:
> >> +Required properties:
> >> + - compatible: "allwinner,sun4i-lradc-keys"
> >> + - reg: mmio address range of the chip
> >> + - interrupts: interrupt to which the chip is connected
> >> + - allwinner,chan0-step: step in mV between keys must be 150 or 200
> >> + - allwinner,chan0-keycodes: array of include/uapi/linux/input.h KEY_
> >> codes> 
> > I think this should be "linux,chan0-keycodes".
> 
> Right, because the codes are Linux specific, will fix in v2.

but the property with its "chan0-" thingy would be allwinner-specific if I'm 
not mistaken.

Also, instead of inventing yet another vendor-specific property, why not re-use 
a button binding similar to gpio-keys like:

       lradc: lradc@01c22800 {
               compatible = "allwinner,sun4i-lradc-keys";
               reg = <0x01c22800 0x100>;
               interrupts = <31>;
               allwinner,chan0-step = <200>;

		#address-cells = <1>;
		#size-cells = <0>;

		button@0 {
			reg = <0>; /* your channel index from above */
			linux,code = <115>; /* already used as dt-property */
		};

		button@1 {
			reg = <1>;
			linux,code = <114>;
		};

...

       };

But I may be on the wrong track here, so I've included the devicetree-people 
for help, which I guess should've been included from the beginning.


Heiko

[PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Heiko Stübner]

Hi Hans, Dmitry,

Am Donnerstag, 2. Januar 2014, 10:37:47 schrieb Hans de Goede:
> Hi,
> 
> On 01/01/2014 09:56 PM, Dmitry Torokhov wrote:
> > Hi Hans,
> > 
> > On Wed, Jan 01, 2014 at 08:30:07PM +0100, Hans de Goede wrote:
> >> +Required properties:
> >> + - compatible: "allwinner,sun4i-lradc-keys"
> >> + - reg: mmio address range of the chip
> >> + - interrupts: interrupt to which the chip is connected
> >> + - allwinner,chan0-step: step in mV between keys must be 150 or 200
> >> + - allwinner,chan0-keycodes: array of include/uapi/linux/input.h KEY_
> >> codes> 
> > I think this should be "linux,chan0-keycodes".
> 
> Right, because the codes are Linux specific, will fix in v2.

but the property with its "chan0-" thingy would be allwinner-specific if I'm 
not mistaken.

Also, instead of inventing yet another vendor-specific property, why not re-use 
a button binding similar to gpio-keys like:

       lradc: lradc at 01c22800 {
               compatible = "allwinner,sun4i-lradc-keys";
               reg = <0x01c22800 0x100>;
               interrupts = <31>;
               allwinner,chan0-step = <200>;

		#address-cells = <1>;
		#size-cells = <0>;

		button at 0 {
			reg = <0>; /* your channel index from above */
			linux,code = <115>; /* already used as dt-property */
		};

		button at 1 {
			reg = <1>;
			linux,code = <114>;
		};

...

       };

But I may be on the wrong track here, so I've included the devicetree-people 
for help, which I guess should've been included from the beginning.


Heiko

Re: [PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Hans de Goede]

Hi,

On 01/02/2014 12:59 PM, Heiko Stübner wrote:
> Hi Hans, Dmitry,
>
> Am Donnerstag, 2. Januar 2014, 10:37:47 schrieb Hans de Goede:
>> Hi,
>>
>> On 01/01/2014 09:56 PM, Dmitry Torokhov wrote:
>>> Hi Hans,
>>>
>>> On Wed, Jan 01, 2014 at 08:30:07PM +0100, Hans de Goede wrote:
>>>> +Required properties:
>>>> + - compatible: "allwinner,sun4i-lradc-keys"
>>>> + - reg: mmio address range of the chip
>>>> + - interrupts: interrupt to which the chip is connected
>>>> + - allwinner,chan0-step: step in mV between keys must be 150 or 200
>>>> + - allwinner,chan0-keycodes: array of include/uapi/linux/input.h KEY_
>>>> codes>
>>> I think this should be "linux,chan0-keycodes".
>>
>> Right, because the codes are Linux specific, will fix in v2.
>
> but the property with its "chan0-" thingy would be allwinner-specific if I'm
> not mistaken.

Correct, but denoting that this is linux only is more important, so as to
avoid namespace collisions.

>
> Also, instead of inventing yet another vendor-specific property, why not re-use
> a button binding similar to gpio-keys like:
>
>         lradc: lradc@01c22800 {
>                 compatible = "allwinner,sun4i-lradc-keys";
>                 reg = <0x01c22800 0x100>;
>                 interrupts = <31>;
>                 allwinner,chan0-step = <200>;
>
> 		#address-cells = <1>;
> 		#size-cells = <0>;
>
> 		button@0 {
> 			reg = <0>; /* your channel index from above */
> 			linux,code = <115>; /* already used as dt-property */
> 		};
>
> 		button@1 {
> 			reg = <1>;
> 			linux,code = <114>;
> 		};

Ugh no. Having a vendor specific property which is KISS certainly beats this,
both wrt ease of writing dts files as well as wrt the dts parsing code in the driver.

Regards,

Hans

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/groups/opt_out.

[PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Hans de Goede]

Hi,

On 01/02/2014 12:59 PM, Heiko St?bner wrote:
> Hi Hans, Dmitry,
>
> Am Donnerstag, 2. Januar 2014, 10:37:47 schrieb Hans de Goede:
>> Hi,
>>
>> On 01/01/2014 09:56 PM, Dmitry Torokhov wrote:
>>> Hi Hans,
>>>
>>> On Wed, Jan 01, 2014 at 08:30:07PM +0100, Hans de Goede wrote:
>>>> +Required properties:
>>>> + - compatible: "allwinner,sun4i-lradc-keys"
>>>> + - reg: mmio address range of the chip
>>>> + - interrupts: interrupt to which the chip is connected
>>>> + - allwinner,chan0-step: step in mV between keys must be 150 or 200
>>>> + - allwinner,chan0-keycodes: array of include/uapi/linux/input.h KEY_
>>>> codes>
>>> I think this should be "linux,chan0-keycodes".
>>
>> Right, because the codes are Linux specific, will fix in v2.
>
> but the property with its "chan0-" thingy would be allwinner-specific if I'm
> not mistaken.

Correct, but denoting that this is linux only is more important, so as to
avoid namespace collisions.

>
> Also, instead of inventing yet another vendor-specific property, why not re-use
> a button binding similar to gpio-keys like:
>
>         lradc: lradc at 01c22800 {
>                 compatible = "allwinner,sun4i-lradc-keys";
>                 reg = <0x01c22800 0x100>;
>                 interrupts = <31>;
>                 allwinner,chan0-step = <200>;
>
> 		#address-cells = <1>;
> 		#size-cells = <0>;
>
> 		button at 0 {
> 			reg = <0>; /* your channel index from above */
> 			linux,code = <115>; /* already used as dt-property */
> 		};
>
> 		button at 1 {
> 			reg = <1>;
> 			linux,code = <114>;
> 		};

Ugh no. Having a vendor specific property which is KISS certainly beats this,
both wrt ease of writing dts files as well as wrt the dts parsing code in the driver.

Regards,

Hans

Re: [PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 1996 bytes --]

On Thu, Jan 02, 2014 at 02:45:29PM +0100, Hans de Goede wrote:
> >Also, instead of inventing yet another vendor-specific property, why not re-use
> >a button binding similar to gpio-keys like:
> >
> >        lradc: lradc@01c22800 {
> >                compatible = "allwinner,sun4i-lradc-keys";
> >                reg = <0x01c22800 0x100>;
> >                interrupts = <31>;
> >                allwinner,chan0-step = <200>;
> >
> >		#address-cells = <1>;
> >		#size-cells = <0>;
> >
> >		button@0 {
> >			reg = <0>; /* your channel index from above */
> >			linux,code = <115>; /* already used as dt-property */
> >		};
> >
> >		button@1 {
> >			reg = <1>;
> >			linux,code = <114>;
> >		};
> 
> Ugh no. Having a vendor specific property which is KISS certainly
> beats this, both wrt ease of writing dts files as well as wrt the
> dts parsing code in the driver.

I'd agree with Heiko here. This is pretty much the same construct
that's already in use in other input drivers, like gpio-keys.

This is also something that can really easily be made generic, since
this is something that is rather common.

Speaking of which. I believe this should actually come in two
different drivers:
  - The ADC driver itself, using IIO
  - A generic button handler driver on top of IIO.

The fact that on most board this adc is used for buttons doesn't make
any difference, it's actually a hardware designer choice, we should
support that choice, but we should also be able to use it just as an
ADC.

Carlo Caione already started to work on an IIO driver for the LRADC:
https://github.com/carlocaione/linux/tree/sunxi-lradc
maybe you can take over his work.

I also wonder wether it would be possible in that case to use reg as
the "button" voltage, to get rid of both the chan0-step property, and
those big fat arrays in the driver.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

[PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Maxime Ripard]

On Thu, Jan 02, 2014 at 02:45:29PM +0100, Hans de Goede wrote:
> >Also, instead of inventing yet another vendor-specific property, why not re-use
> >a button binding similar to gpio-keys like:
> >
> >        lradc: lradc at 01c22800 {
> >                compatible = "allwinner,sun4i-lradc-keys";
> >                reg = <0x01c22800 0x100>;
> >                interrupts = <31>;
> >                allwinner,chan0-step = <200>;
> >
> >		#address-cells = <1>;
> >		#size-cells = <0>;
> >
> >		button at 0 {
> >			reg = <0>; /* your channel index from above */
> >			linux,code = <115>; /* already used as dt-property */
> >		};
> >
> >		button at 1 {
> >			reg = <1>;
> >			linux,code = <114>;
> >		};
> 
> Ugh no. Having a vendor specific property which is KISS certainly
> beats this, both wrt ease of writing dts files as well as wrt the
> dts parsing code in the driver.

I'd agree with Heiko here. This is pretty much the same construct
that's already in use in other input drivers, like gpio-keys.

This is also something that can really easily be made generic, since
this is something that is rather common.

Speaking of which. I believe this should actually come in two
different drivers:
  - The ADC driver itself, using IIO
  - A generic button handler driver on top of IIO.

The fact that on most board this adc is used for buttons doesn't make
any difference, it's actually a hardware designer choice, we should
support that choice, but we should also be able to use it just as an
ADC.

Carlo Caione already started to work on an IIO driver for the LRADC:
https://github.com/carlocaione/linux/tree/sunxi-lradc
maybe you can take over his work.

I also wonder wether it would be possible in that case to use reg as
the "button" voltage, to get rid of both the chan0-step property, and
those big fat arrays in the driver.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140102/abfbd9fe/attachment.sig>

Re: [PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Dmitry Torokhov]

On Thu, Jan 02, 2014 at 09:20:22PM +0100, Maxime Ripard wrote:
> On Thu, Jan 02, 2014 at 02:45:29PM +0100, Hans de Goede wrote:
> > >Also, instead of inventing yet another vendor-specific property, why not re-use
> > >a button binding similar to gpio-keys like:
> > >
> > >        lradc: lradc@01c22800 {
> > >                compatible = "allwinner,sun4i-lradc-keys";
> > >                reg = <0x01c22800 0x100>;
> > >                interrupts = <31>;
> > >                allwinner,chan0-step = <200>;
> > >
> > >		#address-cells = <1>;
> > >		#size-cells = <0>;
> > >
> > >		button@0 {
> > >			reg = <0>; /* your channel index from above */
> > >			linux,code = <115>; /* already used as dt-property */
> > >		};
> > >
> > >		button@1 {
> > >			reg = <1>;
> > >			linux,code = <114>;
> > >		};
> > 
> > Ugh no. Having a vendor specific property which is KISS certainly
> > beats this, both wrt ease of writing dts files as well as wrt the
> > dts parsing code in the driver.
> 
> I'd agree with Heiko here. This is pretty much the same construct
> that's already in use in other input drivers, like gpio-keys.
> 
> This is also something that can really easily be made generic, since
> this is something that is rather common.

Except that button definition from gpio-keys does not use 'reg' property
but rather gpio. I'd rather we did not cram non-applicable attributes
into that definition just to make it "reusable" like that.

I'd be OK with having similar (but not claiming to be the same) mappings
though.

Thanks.

-- 
Dmitry

[PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Dmitry Torokhov]

On Thu, Jan 02, 2014 at 09:20:22PM +0100, Maxime Ripard wrote:
> On Thu, Jan 02, 2014 at 02:45:29PM +0100, Hans de Goede wrote:
> > >Also, instead of inventing yet another vendor-specific property, why not re-use
> > >a button binding similar to gpio-keys like:
> > >
> > >        lradc: lradc at 01c22800 {
> > >                compatible = "allwinner,sun4i-lradc-keys";
> > >                reg = <0x01c22800 0x100>;
> > >                interrupts = <31>;
> > >                allwinner,chan0-step = <200>;
> > >
> > >		#address-cells = <1>;
> > >		#size-cells = <0>;
> > >
> > >		button at 0 {
> > >			reg = <0>; /* your channel index from above */
> > >			linux,code = <115>; /* already used as dt-property */
> > >		};
> > >
> > >		button at 1 {
> > >			reg = <1>;
> > >			linux,code = <114>;
> > >		};
> > 
> > Ugh no. Having a vendor specific property which is KISS certainly
> > beats this, both wrt ease of writing dts files as well as wrt the
> > dts parsing code in the driver.
> 
> I'd agree with Heiko here. This is pretty much the same construct
> that's already in use in other input drivers, like gpio-keys.
> 
> This is also something that can really easily be made generic, since
> this is something that is rather common.

Except that button definition from gpio-keys does not use 'reg' property
but rather gpio. I'd rather we did not cram non-applicable attributes
into that definition just to make it "reusable" like that.

I'd be OK with having similar (but not claiming to be the same) mappings
though.

Thanks.

-- 
Dmitry

Re: [PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 1897 bytes --]

On Thu, Jan 02, 2014 at 12:38:31PM -0800, Dmitry Torokhov wrote:
> On Thu, Jan 02, 2014 at 09:20:22PM +0100, Maxime Ripard wrote:
> > On Thu, Jan 02, 2014 at 02:45:29PM +0100, Hans de Goede wrote:
> > > >Also, instead of inventing yet another vendor-specific property, why not re-use
> > > >a button binding similar to gpio-keys like:
> > > >
> > > >        lradc: lradc@01c22800 {
> > > >                compatible = "allwinner,sun4i-lradc-keys";
> > > >                reg = <0x01c22800 0x100>;
> > > >                interrupts = <31>;
> > > >                allwinner,chan0-step = <200>;
> > > >
> > > >		#address-cells = <1>;
> > > >		#size-cells = <0>;
> > > >
> > > >		button@0 {
> > > >			reg = <0>; /* your channel index from above */
> > > >			linux,code = <115>; /* already used as dt-property */
> > > >		};
> > > >
> > > >		button@1 {
> > > >			reg = <1>;
> > > >			linux,code = <114>;
> > > >		};
> > > 
> > > Ugh no. Having a vendor specific property which is KISS certainly
> > > beats this, both wrt ease of writing dts files as well as wrt the
> > > dts parsing code in the driver.
> > 
> > I'd agree with Heiko here. This is pretty much the same construct
> > that's already in use in other input drivers, like gpio-keys.
> > 
> > This is also something that can really easily be made generic, since
> > this is something that is rather common.
> 
> Except that button definition from gpio-keys does not use 'reg' property
> but rather gpio. I'd rather we did not cram non-applicable attributes
> into that definition just to make it "reusable" like that.
> 
> I'd be OK with having similar (but not claiming to be the same) mappings
> though.

Yes, this is what I was meaning. Sorry if it was not clear enough.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

[PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Maxime Ripard]

On Thu, Jan 02, 2014 at 12:38:31PM -0800, Dmitry Torokhov wrote:
> On Thu, Jan 02, 2014 at 09:20:22PM +0100, Maxime Ripard wrote:
> > On Thu, Jan 02, 2014 at 02:45:29PM +0100, Hans de Goede wrote:
> > > >Also, instead of inventing yet another vendor-specific property, why not re-use
> > > >a button binding similar to gpio-keys like:
> > > >
> > > >        lradc: lradc at 01c22800 {
> > > >                compatible = "allwinner,sun4i-lradc-keys";
> > > >                reg = <0x01c22800 0x100>;
> > > >                interrupts = <31>;
> > > >                allwinner,chan0-step = <200>;
> > > >
> > > >		#address-cells = <1>;
> > > >		#size-cells = <0>;
> > > >
> > > >		button at 0 {
> > > >			reg = <0>; /* your channel index from above */
> > > >			linux,code = <115>; /* already used as dt-property */
> > > >		};
> > > >
> > > >		button at 1 {
> > > >			reg = <1>;
> > > >			linux,code = <114>;
> > > >		};
> > > 
> > > Ugh no. Having a vendor specific property which is KISS certainly
> > > beats this, both wrt ease of writing dts files as well as wrt the
> > > dts parsing code in the driver.
> > 
> > I'd agree with Heiko here. This is pretty much the same construct
> > that's already in use in other input drivers, like gpio-keys.
> > 
> > This is also something that can really easily be made generic, since
> > this is something that is rather common.
> 
> Except that button definition from gpio-keys does not use 'reg' property
> but rather gpio. I'd rather we did not cram non-applicable attributes
> into that definition just to make it "reusable" like that.
> 
> I'd be OK with having similar (but not claiming to be the same) mappings
> though.

Yes, this is what I was meaning. Sorry if it was not clear enough.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140103/b1b5c3a0/attachment.sig>

Re: [PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Hans de Goede]

Hi,

On 01/02/2014 09:20 PM, Maxime Ripard wrote:
> On Thu, Jan 02, 2014 at 02:45:29PM +0100, Hans de Goede wrote:
>>> Also, instead of inventing yet another vendor-specific property, why not re-use
>>> a button binding similar to gpio-keys like:
>>>
>>>         lradc: lradc@01c22800 {
>>>                 compatible = "allwinner,sun4i-lradc-keys";
>>>                 reg = <0x01c22800 0x100>;
>>>                 interrupts = <31>;
>>>                 allwinner,chan0-step = <200>;
>>>
>>> 		#address-cells = <1>;
>>> 		#size-cells = <0>;
>>>
>>> 		button@0 {
>>> 			reg = <0>; /* your channel index from above */
>>> 			linux,code = <115>; /* already used as dt-property */
>>> 		};
>>>
>>> 		button@1 {
>>> 			reg = <1>;
>>> 			linux,code = <114>;
>>> 		};
>>
>> Ugh no. Having a vendor specific property which is KISS certainly
>> beats this, both wrt ease of writing dts files as well as wrt the
>> dts parsing code in the driver.
>
> I'd agree with Heiko here. This is pretty much the same construct
> that's already in use in other input drivers, like gpio-keys.

In the gpio case there is a 1 on 1 relation between a single hw
entity (the gpio-pin) and a single keycode. Here there is 1 hw entity
which maps to an array of key-codes, certainly using an array rather
then a much more complicated construct is the correct data-structure
to represent this.

>
> This is also something that can really easily be made generic, since
> this is something that is rather common.
>
> Speaking of which. I believe this should actually come in two
> different drivers:
>    - The ADC driver itself, using IIO
>    - A generic button handler driver on top of IIO.
 >
 > The fact that on most board this adc is used for buttons doesn't make
 > any difference, it's actually a hardware designer choice, we should
 > support that choice, but we should also be able to use it just as an
 > ADC.

No, this is not a generic adc, as mentioned in the commit msg, this
adc is specifically designed to be used this way.

The adc won't start sampling data, and won't generate any interrupts
until a button is pressed. That is until the input voltage drops below
2/3 of Vref, this is checked through a built-in analog comparator, which
hooks into the control logic.

It has button down and button up interrupts, and can detect long
presses (unused) and generate a second type of down interrupt for those.

This really is an input device, which happens to use an adc.

> Carlo Caione already started to work on an IIO driver for the LRADC:
> https://github.com/carlocaione/linux/tree/sunxi-lradc
> maybe you can take over his work.

That won't work because the adc won't sample if the input gets above
2/3 of Vref. There may be some other mode which does not do that, but
that is not clearly documented.

Even if an IIO driver turns out to be doable, I strongly believe that
having a separate input driver for this is best, since this device
was designed to be used as such. Building input on top of IIO would
mean polling the adc, while with my driver it actually generates
button down / up interrupts without any polling being involved.

And no boards I know of are using this as a generic analog input,
where as many boards are using it as designed.

Regards,

Hans

[PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Hans de Goede]

Hi,

On 01/02/2014 09:20 PM, Maxime Ripard wrote:
> On Thu, Jan 02, 2014 at 02:45:29PM +0100, Hans de Goede wrote:
>>> Also, instead of inventing yet another vendor-specific property, why not re-use
>>> a button binding similar to gpio-keys like:
>>>
>>>         lradc: lradc at 01c22800 {
>>>                 compatible = "allwinner,sun4i-lradc-keys";
>>>                 reg = <0x01c22800 0x100>;
>>>                 interrupts = <31>;
>>>                 allwinner,chan0-step = <200>;
>>>
>>> 		#address-cells = <1>;
>>> 		#size-cells = <0>;
>>>
>>> 		button at 0 {
>>> 			reg = <0>; /* your channel index from above */
>>> 			linux,code = <115>; /* already used as dt-property */
>>> 		};
>>>
>>> 		button at 1 {
>>> 			reg = <1>;
>>> 			linux,code = <114>;
>>> 		};
>>
>> Ugh no. Having a vendor specific property which is KISS certainly
>> beats this, both wrt ease of writing dts files as well as wrt the
>> dts parsing code in the driver.
>
> I'd agree with Heiko here. This is pretty much the same construct
> that's already in use in other input drivers, like gpio-keys.

In the gpio case there is a 1 on 1 relation between a single hw
entity (the gpio-pin) and a single keycode. Here there is 1 hw entity
which maps to an array of key-codes, certainly using an array rather
then a much more complicated construct is the correct data-structure
to represent this.

>
> This is also something that can really easily be made generic, since
> this is something that is rather common.
>
> Speaking of which. I believe this should actually come in two
> different drivers:
>    - The ADC driver itself, using IIO
>    - A generic button handler driver on top of IIO.
 >
 > The fact that on most board this adc is used for buttons doesn't make
 > any difference, it's actually a hardware designer choice, we should
 > support that choice, but we should also be able to use it just as an
 > ADC.

No, this is not a generic adc, as mentioned in the commit msg, this
adc is specifically designed to be used this way.

The adc won't start sampling data, and won't generate any interrupts
until a button is pressed. That is until the input voltage drops below
2/3 of Vref, this is checked through a built-in analog comparator, which
hooks into the control logic.

It has button down and button up interrupts, and can detect long
presses (unused) and generate a second type of down interrupt for those.

This really is an input device, which happens to use an adc.

> Carlo Caione already started to work on an IIO driver for the LRADC:
> https://github.com/carlocaione/linux/tree/sunxi-lradc
> maybe you can take over his work.

That won't work because the adc won't sample if the input gets above
2/3 of Vref. There may be some other mode which does not do that, but
that is not clearly documented.

Even if an IIO driver turns out to be doable, I strongly believe that
having a separate input driver for this is best, since this device
was designed to be used as such. Building input on top of IIO would
mean polling the adc, while with my driver it actually generates
button down / up interrupts without any polling being involved.

And no boards I know of are using this as a generic analog input,
where as many boards are using it as designed.

Regards,

Hans

Re: [PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 4230 bytes --]

On Thu, Jan 02, 2014 at 11:36:33PM +0100, Hans de Goede wrote:
> Hi,
> 
> On 01/02/2014 09:20 PM, Maxime Ripard wrote:
> >On Thu, Jan 02, 2014 at 02:45:29PM +0100, Hans de Goede wrote:
> >>>Also, instead of inventing yet another vendor-specific property, why not re-use
> >>>a button binding similar to gpio-keys like:
> >>>
> >>>        lradc: lradc@01c22800 {
> >>>                compatible = "allwinner,sun4i-lradc-keys";
> >>>                reg = <0x01c22800 0x100>;
> >>>                interrupts = <31>;
> >>>                allwinner,chan0-step = <200>;
> >>>
> >>>		#address-cells = <1>;
> >>>		#size-cells = <0>;
> >>>
> >>>		button@0 {
> >>>			reg = <0>; /* your channel index from above */
> >>>			linux,code = <115>; /* already used as dt-property */
> >>>		};
> >>>
> >>>		button@1 {
> >>>			reg = <1>;
> >>>			linux,code = <114>;
> >>>		};
> >>
> >>Ugh no. Having a vendor specific property which is KISS certainly
> >>beats this, both wrt ease of writing dts files as well as wrt the
> >>dts parsing code in the driver.
> >
> >I'd agree with Heiko here. This is pretty much the same construct
> >that's already in use in other input drivers, like gpio-keys.
> 
> In the gpio case there is a 1 on 1 relation between a single hw
> entity (the gpio-pin) and a single keycode. Here there is 1 hw entity
> which maps to an array of key-codes, certainly using an array rather
> then a much more complicated construct is the correct data-structure
> to represent this.

You can build an array in your driver out of this very easily, it's 10
lines in your probe. And you gain from this something that is more
generic, can be shared by other similar drivers and is consistent with
what is already in use.

> >This is also something that can really easily be made generic,
> >since this is something that is rather common.
> >
> >Speaking of which. I believe this should actually come in two
> >different drivers:
> >   - The ADC driver itself, using IIO
> >   - A generic button handler driver on top of IIO.
> >
> > The fact that on most board this adc is used for buttons doesn't make
> > any difference, it's actually a hardware designer choice, we should
> > support that choice, but we should also be able to use it just as an
> > ADC.
> 
> No, this is not a generic adc, as mentioned in the commit msg, this
> adc is specifically designed to be used this way.
> 
> The adc won't start sampling data, and won't generate any interrupts
> until a button is pressed. That is until the input voltage drops below
> 2/3 of Vref, this is checked through a built-in analog comparator, which
> hooks into the control logic.
> 
> It has button down and button up interrupts, and can detect long
> presses (unused) and generate a second type of down interrupt for those.
> 
> This really is an input device, which happens to use an adc.

Hmm, yes, ok.

> >Carlo Caione already started to work on an IIO driver for the LRADC:
> >https://github.com/carlocaione/linux/tree/sunxi-lradc
> >maybe you can take over his work.
> 
> That won't work because the adc won't sample if the input gets above
> 2/3 of Vref. There may be some other mode which does not do that, but
> that is not clearly documented.
> 
> Even if an IIO driver turns out to be doable, I strongly believe that
> having a separate input driver for this is best, since this device
> was designed to be used as such. Building input on top of IIO would
> mean polling the adc, while with my driver it actually generates
> button down / up interrupts without any polling being involved.

Not really. iio_channel_read calls the read_raw function (in that
case) of your driver. If the read_raw function in your driver wants to
poll the device, fine, but most of the time, it will just block
waiting for an interrupt to come and return the data to the caller,
which is obviously the saner behaviour, and you don't actually end up
polling the device. Which is pretty much the architecture you're using
already, just with an intermediate layer in between.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

[PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Maxime Ripard]

On Thu, Jan 02, 2014 at 11:36:33PM +0100, Hans de Goede wrote:
> Hi,
> 
> On 01/02/2014 09:20 PM, Maxime Ripard wrote:
> >On Thu, Jan 02, 2014 at 02:45:29PM +0100, Hans de Goede wrote:
> >>>Also, instead of inventing yet another vendor-specific property, why not re-use
> >>>a button binding similar to gpio-keys like:
> >>>
> >>>        lradc: lradc at 01c22800 {
> >>>                compatible = "allwinner,sun4i-lradc-keys";
> >>>                reg = <0x01c22800 0x100>;
> >>>                interrupts = <31>;
> >>>                allwinner,chan0-step = <200>;
> >>>
> >>>		#address-cells = <1>;
> >>>		#size-cells = <0>;
> >>>
> >>>		button at 0 {
> >>>			reg = <0>; /* your channel index from above */
> >>>			linux,code = <115>; /* already used as dt-property */
> >>>		};
> >>>
> >>>		button at 1 {
> >>>			reg = <1>;
> >>>			linux,code = <114>;
> >>>		};
> >>
> >>Ugh no. Having a vendor specific property which is KISS certainly
> >>beats this, both wrt ease of writing dts files as well as wrt the
> >>dts parsing code in the driver.
> >
> >I'd agree with Heiko here. This is pretty much the same construct
> >that's already in use in other input drivers, like gpio-keys.
> 
> In the gpio case there is a 1 on 1 relation between a single hw
> entity (the gpio-pin) and a single keycode. Here there is 1 hw entity
> which maps to an array of key-codes, certainly using an array rather
> then a much more complicated construct is the correct data-structure
> to represent this.

You can build an array in your driver out of this very easily, it's 10
lines in your probe. And you gain from this something that is more
generic, can be shared by other similar drivers and is consistent with
what is already in use.

> >This is also something that can really easily be made generic,
> >since this is something that is rather common.
> >
> >Speaking of which. I believe this should actually come in two
> >different drivers:
> >   - The ADC driver itself, using IIO
> >   - A generic button handler driver on top of IIO.
> >
> > The fact that on most board this adc is used for buttons doesn't make
> > any difference, it's actually a hardware designer choice, we should
> > support that choice, but we should also be able to use it just as an
> > ADC.
> 
> No, this is not a generic adc, as mentioned in the commit msg, this
> adc is specifically designed to be used this way.
> 
> The adc won't start sampling data, and won't generate any interrupts
> until a button is pressed. That is until the input voltage drops below
> 2/3 of Vref, this is checked through a built-in analog comparator, which
> hooks into the control logic.
> 
> It has button down and button up interrupts, and can detect long
> presses (unused) and generate a second type of down interrupt for those.
> 
> This really is an input device, which happens to use an adc.

Hmm, yes, ok.

> >Carlo Caione already started to work on an IIO driver for the LRADC:
> >https://github.com/carlocaione/linux/tree/sunxi-lradc
> >maybe you can take over his work.
> 
> That won't work because the adc won't sample if the input gets above
> 2/3 of Vref. There may be some other mode which does not do that, but
> that is not clearly documented.
> 
> Even if an IIO driver turns out to be doable, I strongly believe that
> having a separate input driver for this is best, since this device
> was designed to be used as such. Building input on top of IIO would
> mean polling the adc, while with my driver it actually generates
> button down / up interrupts without any polling being involved.

Not really. iio_channel_read calls the read_raw function (in that
case) of your driver. If the read_raw function in your driver wants to
poll the device, fine, but most of the time, it will just block
waiting for an interrupt to come and return the data to the caller,
which is obviously the saner behaviour, and you don't actually end up
polling the device. Which is pretty much the architecture you're using
already, just with an intermediate layer in between.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140103/51ae2083/attachment-0001.sig>

Re: [PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Dmitry Torokhov]

On Fri, Jan 03, 2014 at 06:36:05PM +0100, Maxime Ripard wrote:
> On Thu, Jan 02, 2014 at 11:36:33PM +0100, Hans de Goede wrote:
> > Hi,
> > 
> > On 01/02/2014 09:20 PM, Maxime Ripard wrote:
> > >On Thu, Jan 02, 2014 at 02:45:29PM +0100, Hans de Goede wrote:
> > >>>Also, instead of inventing yet another vendor-specific property, why not re-use
> > >>>a button binding similar to gpio-keys like:
> > >>>
> > >>>        lradc: lradc@01c22800 {
> > >>>                compatible = "allwinner,sun4i-lradc-keys";
> > >>>                reg = <0x01c22800 0x100>;
> > >>>                interrupts = <31>;
> > >>>                allwinner,chan0-step = <200>;
> > >>>
> > >>>		#address-cells = <1>;
> > >>>		#size-cells = <0>;
> > >>>
> > >>>		button@0 {
> > >>>			reg = <0>; /* your channel index from above */
> > >>>			linux,code = <115>; /* already used as dt-property */
> > >>>		};
> > >>>
> > >>>		button@1 {
> > >>>			reg = <1>;
> > >>>			linux,code = <114>;
> > >>>		};
> > >>
> > >>Ugh no. Having a vendor specific property which is KISS certainly
> > >>beats this, both wrt ease of writing dts files as well as wrt the
> > >>dts parsing code in the driver.
> > >
> > >I'd agree with Heiko here. This is pretty much the same construct
> > >that's already in use in other input drivers, like gpio-keys.
> > 
> > In the gpio case there is a 1 on 1 relation between a single hw
> > entity (the gpio-pin) and a single keycode. Here there is 1 hw entity
> > which maps to an array of key-codes, certainly using an array rather
> > then a much more complicated construct is the correct data-structure
> > to represent this.
> 
> You can build an array in your driver out of this very easily, it's 10
> lines in your probe. And you gain from this something that is more
> generic, can be shared by other similar drivers and is consistent with
> what is already in use.

How will it be shared? Surely not code-wise, but basically in spirit
only. It seems to me that the originally proposed binding is simple and
concise and works well for the driver.

> 
> > >This is also something that can really easily be made generic,
> > >since this is something that is rather common.
> > >
> > >Speaking of which. I believe this should actually come in two
> > >different drivers:
> > >   - The ADC driver itself, using IIO
> > >   - A generic button handler driver on top of IIO.
> > >
> > > The fact that on most board this adc is used for buttons doesn't make
> > > any difference, it's actually a hardware designer choice, we should
> > > support that choice, but we should also be able to use it just as an
> > > ADC.
> > 
> > No, this is not a generic adc, as mentioned in the commit msg, this
> > adc is specifically designed to be used this way.
> > 
> > The adc won't start sampling data, and won't generate any interrupts
> > until a button is pressed. That is until the input voltage drops below
> > 2/3 of Vref, this is checked through a built-in analog comparator, which
> > hooks into the control logic.
> > 
> > It has button down and button up interrupts, and can detect long
> > presses (unused) and generate a second type of down interrupt for those.
> > 
> > This really is an input device, which happens to use an adc.
> 
> Hmm, yes, ok.
> 
> > >Carlo Caione already started to work on an IIO driver for the LRADC:
> > >https://github.com/carlocaione/linux/tree/sunxi-lradc
> > >maybe you can take over his work.
> > 
> > That won't work because the adc won't sample if the input gets above
> > 2/3 of Vref. There may be some other mode which does not do that, but
> > that is not clearly documented.
> > 
> > Even if an IIO driver turns out to be doable, I strongly believe that
> > having a separate input driver for this is best, since this device
> > was designed to be used as such. Building input on top of IIO would
> > mean polling the adc, while with my driver it actually generates
> > button down / up interrupts without any polling being involved.
> 
> Not really. iio_channel_read calls the read_raw function (in that
> case) of your driver. If the read_raw function in your driver wants to
> poll the device, fine, but most of the time, it will just block
> waiting for an interrupt to come and return the data to the caller,
> which is obviously the saner behaviour, and you don't actually end up
> polling the device. Which is pretty much the architecture you're using
> already, just with an intermediate layer in between.

What is the benefit of the IIO layer if device can't really be used as
IIO? I am all for moving as many generic devices as we can to IIO but we
should recognize that sometimes the device is not an IIO device.

Thanks.

-- 
Dmitry

[PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Dmitry Torokhov]

On Fri, Jan 03, 2014 at 06:36:05PM +0100, Maxime Ripard wrote:
> On Thu, Jan 02, 2014 at 11:36:33PM +0100, Hans de Goede wrote:
> > Hi,
> > 
> > On 01/02/2014 09:20 PM, Maxime Ripard wrote:
> > >On Thu, Jan 02, 2014 at 02:45:29PM +0100, Hans de Goede wrote:
> > >>>Also, instead of inventing yet another vendor-specific property, why not re-use
> > >>>a button binding similar to gpio-keys like:
> > >>>
> > >>>        lradc: lradc at 01c22800 {
> > >>>                compatible = "allwinner,sun4i-lradc-keys";
> > >>>                reg = <0x01c22800 0x100>;
> > >>>                interrupts = <31>;
> > >>>                allwinner,chan0-step = <200>;
> > >>>
> > >>>		#address-cells = <1>;
> > >>>		#size-cells = <0>;
> > >>>
> > >>>		button at 0 {
> > >>>			reg = <0>; /* your channel index from above */
> > >>>			linux,code = <115>; /* already used as dt-property */
> > >>>		};
> > >>>
> > >>>		button at 1 {
> > >>>			reg = <1>;
> > >>>			linux,code = <114>;
> > >>>		};
> > >>
> > >>Ugh no. Having a vendor specific property which is KISS certainly
> > >>beats this, both wrt ease of writing dts files as well as wrt the
> > >>dts parsing code in the driver.
> > >
> > >I'd agree with Heiko here. This is pretty much the same construct
> > >that's already in use in other input drivers, like gpio-keys.
> > 
> > In the gpio case there is a 1 on 1 relation between a single hw
> > entity (the gpio-pin) and a single keycode. Here there is 1 hw entity
> > which maps to an array of key-codes, certainly using an array rather
> > then a much more complicated construct is the correct data-structure
> > to represent this.
> 
> You can build an array in your driver out of this very easily, it's 10
> lines in your probe. And you gain from this something that is more
> generic, can be shared by other similar drivers and is consistent with
> what is already in use.

How will it be shared? Surely not code-wise, but basically in spirit
only. It seems to me that the originally proposed binding is simple and
concise and works well for the driver.

> 
> > >This is also something that can really easily be made generic,
> > >since this is something that is rather common.
> > >
> > >Speaking of which. I believe this should actually come in two
> > >different drivers:
> > >   - The ADC driver itself, using IIO
> > >   - A generic button handler driver on top of IIO.
> > >
> > > The fact that on most board this adc is used for buttons doesn't make
> > > any difference, it's actually a hardware designer choice, we should
> > > support that choice, but we should also be able to use it just as an
> > > ADC.
> > 
> > No, this is not a generic adc, as mentioned in the commit msg, this
> > adc is specifically designed to be used this way.
> > 
> > The adc won't start sampling data, and won't generate any interrupts
> > until a button is pressed. That is until the input voltage drops below
> > 2/3 of Vref, this is checked through a built-in analog comparator, which
> > hooks into the control logic.
> > 
> > It has button down and button up interrupts, and can detect long
> > presses (unused) and generate a second type of down interrupt for those.
> > 
> > This really is an input device, which happens to use an adc.
> 
> Hmm, yes, ok.
> 
> > >Carlo Caione already started to work on an IIO driver for the LRADC:
> > >https://github.com/carlocaione/linux/tree/sunxi-lradc
> > >maybe you can take over his work.
> > 
> > That won't work because the adc won't sample if the input gets above
> > 2/3 of Vref. There may be some other mode which does not do that, but
> > that is not clearly documented.
> > 
> > Even if an IIO driver turns out to be doable, I strongly believe that
> > having a separate input driver for this is best, since this device
> > was designed to be used as such. Building input on top of IIO would
> > mean polling the adc, while with my driver it actually generates
> > button down / up interrupts without any polling being involved.
> 
> Not really. iio_channel_read calls the read_raw function (in that
> case) of your driver. If the read_raw function in your driver wants to
> poll the device, fine, but most of the time, it will just block
> waiting for an interrupt to come and return the data to the caller,
> which is obviously the saner behaviour, and you don't actually end up
> polling the device. Which is pretty much the architecture you're using
> already, just with an intermediate layer in between.

What is the benefit of the IIO layer if device can't really be used as
IIO? I am all for moving as many generic devices as we can to IIO but we
should recognize that sometimes the device is not an IIO device.

Thanks.

-- 
Dmitry

Re: [PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Heiko Stübner]

Am Freitag, 3. Januar 2014, 10:23:50 schrieb Dmitry Torokhov:
> On Fri, Jan 03, 2014 at 06:36:05PM +0100, Maxime Ripard wrote:
> > On Thu, Jan 02, 2014 at 11:36:33PM +0100, Hans de Goede wrote:
> > > Hi,
> > > 
> > > On 01/02/2014 09:20 PM, Maxime Ripard wrote:
> > > >On Thu, Jan 02, 2014 at 02:45:29PM +0100, Hans de Goede wrote:
> > > >>>Also, instead of inventing yet another vendor-specific property, why
> > > >>>not re-use> > >>>
> > > >>>a button binding similar to gpio-keys like:
> > > >>>        lradc: lradc@01c22800 {
> > > >>>        
> > > >>>                compatible = "allwinner,sun4i-lradc-keys";
> > > >>>                reg = <0x01c22800 0x100>;
> > > >>>                interrupts = <31>;
> > > >>>                allwinner,chan0-step = <200>;
> > > >>>		
> > > >>>		#address-cells = <1>;
> > > >>>		#size-cells = <0>;
> > > >>>		
> > > >>>		button@0 {
> > > >>>		
> > > >>>			reg = <0>; /* your channel index from above */
> > > >>>			linux,code = <115>; /* already used as dt-property */
> > > >>>		
> > > >>>		};
> > > >>>		
> > > >>>		button@1 {
> > > >>>		
> > > >>>			reg = <1>;
> > > >>>			linux,code = <114>;
> > > >>>		
> > > >>>		};
> > > >>
> > > >>Ugh no. Having a vendor specific property which is KISS certainly
> > > >>beats this, both wrt ease of writing dts files as well as wrt the
> > > >>dts parsing code in the driver.
> > > >
> > > >I'd agree with Heiko here. This is pretty much the same construct
> > > >that's already in use in other input drivers, like gpio-keys.
> > > 
> > > In the gpio case there is a 1 on 1 relation between a single hw
> > > entity (the gpio-pin) and a single keycode. Here there is 1 hw entity
> > > which maps to an array of key-codes, certainly using an array rather
> > > then a much more complicated construct is the correct data-structure
> > > to represent this.
> > 
> > You can build an array in your driver out of this very easily, it's 10
> > lines in your probe. And you gain from this something that is more
> > generic, can be shared by other similar drivers and is consistent with
> > what is already in use.
> 
> How will it be shared? Surely not code-wise, but basically in spirit
> only. It seems to me that the originally proposed binding is simple and
> concise and works well for the driver.

I don't think "binding [...] works well for the driver" is the correct 
direction. From my understanding the binding should describe the hardware in 
an os-agnostic way (so "linux,foo" properties should stay the exception) and 
not the data structures used in the driver. The driver itself then implements 
the binding to convert the binding-data into a structure it wants to use.

The sharing would, as you suggested, be in spirit and in the use of already 
established dt-properties without introducing more non-standard ones.


Heiko

[PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Heiko Stübner]

Am Freitag, 3. Januar 2014, 10:23:50 schrieb Dmitry Torokhov:
> On Fri, Jan 03, 2014 at 06:36:05PM +0100, Maxime Ripard wrote:
> > On Thu, Jan 02, 2014 at 11:36:33PM +0100, Hans de Goede wrote:
> > > Hi,
> > > 
> > > On 01/02/2014 09:20 PM, Maxime Ripard wrote:
> > > >On Thu, Jan 02, 2014 at 02:45:29PM +0100, Hans de Goede wrote:
> > > >>>Also, instead of inventing yet another vendor-specific property, why
> > > >>>not re-use> > >>>
> > > >>>a button binding similar to gpio-keys like:
> > > >>>        lradc: lradc at 01c22800 {
> > > >>>        
> > > >>>                compatible = "allwinner,sun4i-lradc-keys";
> > > >>>                reg = <0x01c22800 0x100>;
> > > >>>                interrupts = <31>;
> > > >>>                allwinner,chan0-step = <200>;
> > > >>>		
> > > >>>		#address-cells = <1>;
> > > >>>		#size-cells = <0>;
> > > >>>		
> > > >>>		button at 0 {
> > > >>>		
> > > >>>			reg = <0>; /* your channel index from above */
> > > >>>			linux,code = <115>; /* already used as dt-property */
> > > >>>		
> > > >>>		};
> > > >>>		
> > > >>>		button at 1 {
> > > >>>		
> > > >>>			reg = <1>;
> > > >>>			linux,code = <114>;
> > > >>>		
> > > >>>		};
> > > >>
> > > >>Ugh no. Having a vendor specific property which is KISS certainly
> > > >>beats this, both wrt ease of writing dts files as well as wrt the
> > > >>dts parsing code in the driver.
> > > >
> > > >I'd agree with Heiko here. This is pretty much the same construct
> > > >that's already in use in other input drivers, like gpio-keys.
> > > 
> > > In the gpio case there is a 1 on 1 relation between a single hw
> > > entity (the gpio-pin) and a single keycode. Here there is 1 hw entity
> > > which maps to an array of key-codes, certainly using an array rather
> > > then a much more complicated construct is the correct data-structure
> > > to represent this.
> > 
> > You can build an array in your driver out of this very easily, it's 10
> > lines in your probe. And you gain from this something that is more
> > generic, can be shared by other similar drivers and is consistent with
> > what is already in use.
> 
> How will it be shared? Surely not code-wise, but basically in spirit
> only. It seems to me that the originally proposed binding is simple and
> concise and works well for the driver.

I don't think "binding [...] works well for the driver" is the correct 
direction. From my understanding the binding should describe the hardware in 
an os-agnostic way (so "linux,foo" properties should stay the exception) and 
not the data structures used in the driver. The driver itself then implements 
the binding to convert the binding-data into a structure it wants to use.

The sharing would, as you suggested, be in spirit and in the use of already 
established dt-properties without introducing more non-standard ones.


Heiko

Re: [PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 5302 bytes --]

On Fri, Jan 03, 2014 at 10:23:50AM -0800, Dmitry Torokhov wrote:
> On Fri, Jan 03, 2014 at 06:36:05PM +0100, Maxime Ripard wrote:
> > On Thu, Jan 02, 2014 at 11:36:33PM +0100, Hans de Goede wrote:
> > > Hi,
> > > 
> > > On 01/02/2014 09:20 PM, Maxime Ripard wrote:
> > > >On Thu, Jan 02, 2014 at 02:45:29PM +0100, Hans de Goede wrote:
> > > >>>Also, instead of inventing yet another vendor-specific property, why not re-use
> > > >>>a button binding similar to gpio-keys like:
> > > >>>
> > > >>>        lradc: lradc@01c22800 {
> > > >>>                compatible = "allwinner,sun4i-lradc-keys";
> > > >>>                reg = <0x01c22800 0x100>;
> > > >>>                interrupts = <31>;
> > > >>>                allwinner,chan0-step = <200>;
> > > >>>
> > > >>>		#address-cells = <1>;
> > > >>>		#size-cells = <0>;
> > > >>>
> > > >>>		button@0 {
> > > >>>			reg = <0>; /* your channel index from above */
> > > >>>			linux,code = <115>; /* already used as dt-property */
> > > >>>		};
> > > >>>
> > > >>>		button@1 {
> > > >>>			reg = <1>;
> > > >>>			linux,code = <114>;
> > > >>>		};
> > > >>
> > > >>Ugh no. Having a vendor specific property which is KISS certainly
> > > >>beats this, both wrt ease of writing dts files as well as wrt the
> > > >>dts parsing code in the driver.
> > > >
> > > >I'd agree with Heiko here. This is pretty much the same construct
> > > >that's already in use in other input drivers, like gpio-keys.
> > > 
> > > In the gpio case there is a 1 on 1 relation between a single hw
> > > entity (the gpio-pin) and a single keycode. Here there is 1 hw entity
> > > which maps to an array of key-codes, certainly using an array rather
> > > then a much more complicated construct is the correct data-structure
> > > to represent this.
> > 
> > You can build an array in your driver out of this very easily, it's 10
> > lines in your probe. And you gain from this something that is more
> > generic, can be shared by other similar drivers and is consistent with
> > what is already in use.
> 
> How will it be shared? Surely not code-wise, but basically in spirit
> only. It seems to me that the originally proposed binding is simple and
> concise and works well for the driver.

See Heiko's answer, but I do believe the code can be shared as well if
needs be.

> > > >This is also something that can really easily be made generic,
> > > >since this is something that is rather common.
> > > >
> > > >Speaking of which. I believe this should actually come in two
> > > >different drivers:
> > > >   - The ADC driver itself, using IIO
> > > >   - A generic button handler driver on top of IIO.
> > > >
> > > > The fact that on most board this adc is used for buttons doesn't make
> > > > any difference, it's actually a hardware designer choice, we should
> > > > support that choice, but we should also be able to use it just as an
> > > > ADC.
> > > 
> > > No, this is not a generic adc, as mentioned in the commit msg, this
> > > adc is specifically designed to be used this way.
> > > 
> > > The adc won't start sampling data, and won't generate any interrupts
> > > until a button is pressed. That is until the input voltage drops below
> > > 2/3 of Vref, this is checked through a built-in analog comparator, which
> > > hooks into the control logic.
> > > 
> > > It has button down and button up interrupts, and can detect long
> > > presses (unused) and generate a second type of down interrupt for those.
> > > 
> > > This really is an input device, which happens to use an adc.
> > 
> > Hmm, yes, ok.
> > 
> > > >Carlo Caione already started to work on an IIO driver for the LRADC:
> > > >https://github.com/carlocaione/linux/tree/sunxi-lradc
> > > >maybe you can take over his work.
> > > 
> > > That won't work because the adc won't sample if the input gets above
> > > 2/3 of Vref. There may be some other mode which does not do that, but
> > > that is not clearly documented.
> > > 
> > > Even if an IIO driver turns out to be doable, I strongly believe that
> > > having a separate input driver for this is best, since this device
> > > was designed to be used as such. Building input on top of IIO would
> > > mean polling the adc, while with my driver it actually generates
> > > button down / up interrupts without any polling being involved.
> > 
> > Not really. iio_channel_read calls the read_raw function (in that
> > case) of your driver. If the read_raw function in your driver wants to
> > poll the device, fine, but most of the time, it will just block
> > waiting for an interrupt to come and return the data to the caller,
> > which is obviously the saner behaviour, and you don't actually end up
> > polling the device. Which is pretty much the architecture you're using
> > already, just with an intermediate layer in between.
> 
> What is the benefit of the IIO layer if device can't really be used as
> IIO? I am all for moving as many generic devices as we can to IIO but we
> should recognize that sometimes the device is not an IIO device.

Yes, I've agreed to that. I was just clarifying Hans' statement.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

[PATCH 1/4] input: Add new sun4i-lradc-keys drivers

[Maxime Ripard]

On Fri, Jan 03, 2014 at 10:23:50AM -0800, Dmitry Torokhov wrote:
> On Fri, Jan 03, 2014 at 06:36:05PM +0100, Maxime Ripard wrote:
> > On Thu, Jan 02, 2014 at 11:36:33PM +0100, Hans de Goede wrote:
> > > Hi,
> > > 
> > > On 01/02/2014 09:20 PM, Maxime Ripard wrote:
> > > >On Thu, Jan 02, 2014 at 02:45:29PM +0100, Hans de Goede wrote:
> > > >>>Also, instead of inventing yet another vendor-specific property, why not re-use
> > > >>>a button binding similar to gpio-keys like:
> > > >>>
> > > >>>        lradc: lradc at 01c22800 {
> > > >>>                compatible = "allwinner,sun4i-lradc-keys";
> > > >>>                reg = <0x01c22800 0x100>;
> > > >>>                interrupts = <31>;
> > > >>>                allwinner,chan0-step = <200>;
> > > >>>
> > > >>>		#address-cells = <1>;
> > > >>>		#size-cells = <0>;
> > > >>>
> > > >>>		button at 0 {
> > > >>>			reg = <0>; /* your channel index from above */
> > > >>>			linux,code = <115>; /* already used as dt-property */
> > > >>>		};
> > > >>>
> > > >>>		button at 1 {
> > > >>>			reg = <1>;
> > > >>>			linux,code = <114>;
> > > >>>		};
> > > >>
> > > >>Ugh no. Having a vendor specific property which is KISS certainly
> > > >>beats this, both wrt ease of writing dts files as well as wrt the
> > > >>dts parsing code in the driver.
> > > >
> > > >I'd agree with Heiko here. This is pretty much the same construct
> > > >that's already in use in other input drivers, like gpio-keys.
> > > 
> > > In the gpio case there is a 1 on 1 relation between a single hw
> > > entity (the gpio-pin) and a single keycode. Here there is 1 hw entity
> > > which maps to an array of key-codes, certainly using an array rather
> > > then a much more complicated construct is the correct data-structure
> > > to represent this.
> > 
> > You can build an array in your driver out of this very easily, it's 10
> > lines in your probe. And you gain from this something that is more
> > generic, can be shared by other similar drivers and is consistent with
> > what is already in use.
> 
> How will it be shared? Surely not code-wise, but basically in spirit
> only. It seems to me that the originally proposed binding is simple and
> concise and works well for the driver.

See Heiko's answer, but I do believe the code can be shared as well if
needs be.

> > > >This is also something that can really easily be made generic,
> > > >since this is something that is rather common.
> > > >
> > > >Speaking of which. I believe this should actually come in two
> > > >different drivers:
> > > >   - The ADC driver itself, using IIO
> > > >   - A generic button handler driver on top of IIO.
> > > >
> > > > The fact that on most board this adc is used for buttons doesn't make
> > > > any difference, it's actually a hardware designer choice, we should
> > > > support that choice, but we should also be able to use it just as an
> > > > ADC.
> > > 
> > > No, this is not a generic adc, as mentioned in the commit msg, this
> > > adc is specifically designed to be used this way.
> > > 
> > > The adc won't start sampling data, and won't generate any interrupts
> > > until a button is pressed. That is until the input voltage drops below
> > > 2/3 of Vref, this is checked through a built-in analog comparator, which
> > > hooks into the control logic.
> > > 
> > > It has button down and button up interrupts, and can detect long
> > > presses (unused) and generate a second type of down interrupt for those.
> > > 
> > > This really is an input device, which happens to use an adc.
> > 
> > Hmm, yes, ok.
> > 
> > > >Carlo Caione already started to work on an IIO driver for the LRADC:
> > > >https://github.com/carlocaione/linux/tree/sunxi-lradc
> > > >maybe you can take over his work.
> > > 
> > > That won't work because the adc won't sample if the input gets above
> > > 2/3 of Vref. There may be some other mode which does not do that, but
> > > that is not clearly documented.
> > > 
> > > Even if an IIO driver turns out to be doable, I strongly believe that
> > > having a separate input driver for this is best, since this device
> > > was designed to be used as such. Building input on top of IIO would
> > > mean polling the adc, while with my driver it actually generates
> > > button down / up interrupts without any polling being involved.
> > 
> > Not really. iio_channel_read calls the read_raw function (in that
> > case) of your driver. If the read_raw function in your driver wants to
> > poll the device, fine, but most of the time, it will just block
> > waiting for an interrupt to come and return the data to the caller,
> > which is obviously the saner behaviour, and you don't actually end up
> > polling the device. Which is pretty much the architecture you're using
> > already, just with an intermediate layer in between.
> 
> What is the benefit of the IIO layer if device can't really be used as
> IIO? I am all for moving as many generic devices as we can to IIO but we
> should recognize that sometimes the device is not an IIO device.

Yes, I've agreed to that. I was just clarifying Hans' statement.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140106/7fcbda8b/attachment.sig>

[PATCH 2/4] ARM: dts: sun4i: Add lradc node

[Hans de Goede]

Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
---
 arch/arm/boot/dts/sun4i-a10.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/sun4i-a10.dtsi b/arch/arm/boot/dts/sun4i-a10.dtsi
index 502f3e2..88f119a 100644
--- a/arch/arm/boot/dts/sun4i-a10.dtsi
+++ b/arch/arm/boot/dts/sun4i-a10.dtsi
@@ -447,6 +447,13 @@
 			interrupts = <24>;
 		};
 
+		lradc: lradc@01c22800 {
+			compatible = "allwinner,sun4i-lradc-keys";
+			reg = <0x01c22800 0x100>;
+			interrupts = <31>;
+			status = "disabled";
+		};
+
 		sid: eeprom@01c23800 {
 			compatible = "allwinner,sun4i-sid";
 			reg = <0x01c23800 0x10>;
-- 
1.8.4.2

[PATCH 2/4] ARM: dts: sun4i: Add lradc node

[Hans de Goede]

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 arch/arm/boot/dts/sun4i-a10.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/sun4i-a10.dtsi b/arch/arm/boot/dts/sun4i-a10.dtsi
index 502f3e2..88f119a 100644
--- a/arch/arm/boot/dts/sun4i-a10.dtsi
+++ b/arch/arm/boot/dts/sun4i-a10.dtsi
@@ -447,6 +447,13 @@
 			interrupts = <24>;
 		};
 
+		lradc: lradc at 01c22800 {
+			compatible = "allwinner,sun4i-lradc-keys";
+			reg = <0x01c22800 0x100>;
+			interrupts = <31>;
+			status = "disabled";
+		};
+
 		sid: eeprom at 01c23800 {
 			compatible = "allwinner,sun4i-sid";
 			reg = <0x01c23800 0x10>;
-- 
1.8.4.2

[PATCH 3/4] ARM: dts: sun5i: Add lradc node

[Hans de Goede]

Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
---
 arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts | 7 +++++++
 arch/arm/boot/dts/sun5i-a10s.dtsi                | 7 +++++++
 arch/arm/boot/dts/sun5i-a13-olinuxino.dts        | 7 +++++++
 arch/arm/boot/dts/sun5i-a13.dtsi                 | 7 +++++++
 4 files changed, 28 insertions(+)

diff --git a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
index e53fb12..c32162e 100644
--- a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
+++ b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
@@ -75,6 +75,13 @@
 			};
 		};
 
+		lradc: lradc@01c22800 {
+			allwinner,chan0-step = <200>;
+			/* KEY_VOLUMEUP VOLUMEDOWN MENU ENTER HOME */
+			allwinner,chan0-keycodes = <115 114 139 28 102>;
+			status = "okay";
+		};
+
 		uart0: serial@01c28000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart0_pins_a>;
diff --git a/arch/arm/boot/dts/sun5i-a10s.dtsi b/arch/arm/boot/dts/sun5i-a10s.dtsi
index 34dd303..8775bad 100644
--- a/arch/arm/boot/dts/sun5i-a10s.dtsi
+++ b/arch/arm/boot/dts/sun5i-a10s.dtsi
@@ -404,6 +404,13 @@
 			reg = <0x01c20c90 0x10>;
 		};
 
+		lradc: lradc@01c22800 {
+			compatible = "allwinner,sun4i-lradc-keys";
+			reg = <0x01c22800 0x100>;
+			interrupts = <31>;
+			status = "disabled";
+		};
+
 		sid: eeprom@01c23800 {
 			compatible = "allwinner,sun4i-sid";
 			reg = <0x01c23800 0x10>;
diff --git a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts b/arch/arm/boot/dts/sun5i-a13-olinuxino.dts
index ab566f7..ce31361 100644
--- a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts
+++ b/arch/arm/boot/dts/sun5i-a13-olinuxino.dts
@@ -55,6 +55,13 @@
 			};
 		};
 
+		lradc: lradc@01c22800 {
+			allwinner,chan0-step = <200>;
+			/* KEY_VOLUMEUP VOLUMEDOWN MENU ENTER HOME */
+			allwinner,chan0-keycodes = <115 114 139 28 102>;
+			status = "okay";
+		};
+
 		uart1: serial@01c28400 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart1_pins_b>;
diff --git a/arch/arm/boot/dts/sun5i-a13.dtsi b/arch/arm/boot/dts/sun5i-a13.dtsi
index 264cfa4..90c1ed3 100644
--- a/arch/arm/boot/dts/sun5i-a13.dtsi
+++ b/arch/arm/boot/dts/sun5i-a13.dtsi
@@ -362,6 +362,13 @@
 			reg = <0x01c20c90 0x10>;
 		};
 
+		lradc: lradc@01c22800 {
+			compatible = "allwinner,sun4i-lradc-keys";
+			reg = <0x01c22800 0x100>;
+			interrupts = <31>;
+			status = "disabled";
+		};
+
 		sid: eeprom@01c23800 {
 			compatible = "allwinner,sun4i-sid";
 			reg = <0x01c23800 0x10>;
-- 
1.8.4.2

[PATCH 3/4] ARM: dts: sun5i: Add lradc node

[Hans de Goede]

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts | 7 +++++++
 arch/arm/boot/dts/sun5i-a10s.dtsi                | 7 +++++++
 arch/arm/boot/dts/sun5i-a13-olinuxino.dts        | 7 +++++++
 arch/arm/boot/dts/sun5i-a13.dtsi                 | 7 +++++++
 4 files changed, 28 insertions(+)

diff --git a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
index e53fb12..c32162e 100644
--- a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
+++ b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
@@ -75,6 +75,13 @@
 			};
 		};
 
+		lradc: lradc at 01c22800 {
+			allwinner,chan0-step = <200>;
+			/* KEY_VOLUMEUP VOLUMEDOWN MENU ENTER HOME */
+			allwinner,chan0-keycodes = <115 114 139 28 102>;
+			status = "okay";
+		};
+
 		uart0: serial at 01c28000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart0_pins_a>;
diff --git a/arch/arm/boot/dts/sun5i-a10s.dtsi b/arch/arm/boot/dts/sun5i-a10s.dtsi
index 34dd303..8775bad 100644
--- a/arch/arm/boot/dts/sun5i-a10s.dtsi
+++ b/arch/arm/boot/dts/sun5i-a10s.dtsi
@@ -404,6 +404,13 @@
 			reg = <0x01c20c90 0x10>;
 		};
 
+		lradc: lradc at 01c22800 {
+			compatible = "allwinner,sun4i-lradc-keys";
+			reg = <0x01c22800 0x100>;
+			interrupts = <31>;
+			status = "disabled";
+		};
+
 		sid: eeprom at 01c23800 {
 			compatible = "allwinner,sun4i-sid";
 			reg = <0x01c23800 0x10>;
diff --git a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts b/arch/arm/boot/dts/sun5i-a13-olinuxino.dts
index ab566f7..ce31361 100644
--- a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts
+++ b/arch/arm/boot/dts/sun5i-a13-olinuxino.dts
@@ -55,6 +55,13 @@
 			};
 		};
 
+		lradc: lradc at 01c22800 {
+			allwinner,chan0-step = <200>;
+			/* KEY_VOLUMEUP VOLUMEDOWN MENU ENTER HOME */
+			allwinner,chan0-keycodes = <115 114 139 28 102>;
+			status = "okay";
+		};
+
 		uart1: serial at 01c28400 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart1_pins_b>;
diff --git a/arch/arm/boot/dts/sun5i-a13.dtsi b/arch/arm/boot/dts/sun5i-a13.dtsi
index 264cfa4..90c1ed3 100644
--- a/arch/arm/boot/dts/sun5i-a13.dtsi
+++ b/arch/arm/boot/dts/sun5i-a13.dtsi
@@ -362,6 +362,13 @@
 			reg = <0x01c20c90 0x10>;
 		};
 
+		lradc: lradc at 01c22800 {
+			compatible = "allwinner,sun4i-lradc-keys";
+			reg = <0x01c22800 0x100>;
+			interrupts = <31>;
+			status = "disabled";
+		};
+
 		sid: eeprom at 01c23800 {
 			compatible = "allwinner,sun4i-sid";
 			reg = <0x01c23800 0x10>;
-- 
1.8.4.2

Re: [PATCH 3/4] ARM: dts: sun5i: Add lradc node

[Andrew Lunn]

On Wed, Jan 01, 2014 at 08:30:09PM +0100, Hans de Goede wrote:
> Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
> ---
>  arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts | 7 +++++++
>  arch/arm/boot/dts/sun5i-a10s.dtsi                | 7 +++++++
>  arch/arm/boot/dts/sun5i-a13-olinuxino.dts        | 7 +++++++
>  arch/arm/boot/dts/sun5i-a13.dtsi                 | 7 +++++++
>  4 files changed, 28 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
> index e53fb12..c32162e 100644
> --- a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
> +++ b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
> @@ -75,6 +75,13 @@
>  			};
>  		};
>  
> +		lradc: lradc@01c22800 {
> +			allwinner,chan0-step = <200>;
> +			/* KEY_VOLUMEUP VOLUMEDOWN MENU ENTER HOME */
> +			allwinner,chan0-keycodes = <115 114 139 28 102>;

Hi Hans

You might want to consider using arch/arm/boot/dts/include/dt-bindings/input/input.h

and then you could have the node:

> +		lradc: lradc@01c22800 {
> +			allwinner,chan0-step = <200>;
> +			allwinner,chan0-keycodes = <KEY_VOLUMEUP VOLUMEDOWN MENU ENTER HOME>;

which is much more readable.

      Andrew

[PATCH 3/4] ARM: dts: sun5i: Add lradc node

[Andrew Lunn]

On Wed, Jan 01, 2014 at 08:30:09PM +0100, Hans de Goede wrote:
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
>  arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts | 7 +++++++
>  arch/arm/boot/dts/sun5i-a10s.dtsi                | 7 +++++++
>  arch/arm/boot/dts/sun5i-a13-olinuxino.dts        | 7 +++++++
>  arch/arm/boot/dts/sun5i-a13.dtsi                 | 7 +++++++
>  4 files changed, 28 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
> index e53fb12..c32162e 100644
> --- a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
> +++ b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
> @@ -75,6 +75,13 @@
>  			};
>  		};
>  
> +		lradc: lradc at 01c22800 {
> +			allwinner,chan0-step = <200>;
> +			/* KEY_VOLUMEUP VOLUMEDOWN MENU ENTER HOME */
> +			allwinner,chan0-keycodes = <115 114 139 28 102>;

Hi Hans

You might want to consider using arch/arm/boot/dts/include/dt-bindings/input/input.h

and then you could have the node:

> +		lradc: lradc at 01c22800 {
> +			allwinner,chan0-step = <200>;
> +			allwinner,chan0-keycodes = <KEY_VOLUMEUP VOLUMEDOWN MENU ENTER HOME>;

which is much more readable.

      Andrew

Re: Re: [PATCH 3/4] ARM: dts: sun5i: Add lradc node

[Hans de Goede]

Hi,

On 01/01/2014 08:45 PM, Andrew Lunn wrote:
> On Wed, Jan 01, 2014 at 08:30:09PM +0100, Hans de Goede wrote:
>> Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
>> ---
>>   arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts | 7 +++++++
>>   arch/arm/boot/dts/sun5i-a10s.dtsi                | 7 +++++++
>>   arch/arm/boot/dts/sun5i-a13-olinuxino.dts        | 7 +++++++
>>   arch/arm/boot/dts/sun5i-a13.dtsi                 | 7 +++++++
>>   4 files changed, 28 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
>> index e53fb12..c32162e 100644
>> --- a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
>> +++ b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
>> @@ -75,6 +75,13 @@
>>   			};
>>   		};
>>
>> +		lradc: lradc@01c22800 {
>> +			allwinner,chan0-step = <200>;
>> +			/* KEY_VOLUMEUP VOLUMEDOWN MENU ENTER HOME */
>> +			allwinner,chan0-keycodes = <115 114 139 28 102>;
>
> Hi Hans
>
> You might want to consider using arch/arm/boot/dts/include/dt-bindings/input/input.h
>
> and then you could have the node:
>
>> +		lradc: lradc@01c22800 {
>> +			allwinner,chan0-step = <200>;
>> +			allwinner,chan0-keycodes = <KEY_VOLUMEUP VOLUMEDOWN MENU ENTER HOME>;
>
> which is much more readable.

Ah, I did not know about that include. Good tip, will fix this in v2.

Regards,

Hans

[linux-sunxi] Re: [PATCH 3/4] ARM: dts: sun5i: Add lradc node

[Hans de Goede]

Hi,

On 01/01/2014 08:45 PM, Andrew Lunn wrote:
> On Wed, Jan 01, 2014 at 08:30:09PM +0100, Hans de Goede wrote:
>> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
>> ---
>>   arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts | 7 +++++++
>>   arch/arm/boot/dts/sun5i-a10s.dtsi                | 7 +++++++
>>   arch/arm/boot/dts/sun5i-a13-olinuxino.dts        | 7 +++++++
>>   arch/arm/boot/dts/sun5i-a13.dtsi                 | 7 +++++++
>>   4 files changed, 28 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
>> index e53fb12..c32162e 100644
>> --- a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
>> +++ b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
>> @@ -75,6 +75,13 @@
>>   			};
>>   		};
>>
>> +		lradc: lradc at 01c22800 {
>> +			allwinner,chan0-step = <200>;
>> +			/* KEY_VOLUMEUP VOLUMEDOWN MENU ENTER HOME */
>> +			allwinner,chan0-keycodes = <115 114 139 28 102>;
>
> Hi Hans
>
> You might want to consider using arch/arm/boot/dts/include/dt-bindings/input/input.h
>
> and then you could have the node:
>
>> +		lradc: lradc at 01c22800 {
>> +			allwinner,chan0-step = <200>;
>> +			allwinner,chan0-keycodes = <KEY_VOLUMEUP VOLUMEDOWN MENU ENTER HOME>;
>
> which is much more readable.

Ah, I did not know about that include. Good tip, will fix this in v2.

Regards,

Hans

[PATCH 4/4] ARM: dts: sun7i: Add lradc node

[Hans de Goede]

Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
---
 arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts | 7 +++++++
 arch/arm/boot/dts/sun7i-a20.dtsi                | 7 +++++++
 2 files changed, 14 insertions(+)

diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
index 0ee2641..dcf9db7 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
+++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
@@ -86,6 +86,13 @@
 			};
 		};
 
+		lradc: lradc@01c22800 {
+			allwinner,chan0-step = <200>;
+			/* VOLUMEUP VOLUMEDOWN MENU SEARCH HOME ESC ENTER */
+			allwinner,chan0-keycodes = <115 114 139 217 102 1 28>;
+			status = "okay";
+		};
+
 		uart0: serial@01c28000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart0_pins_a>;
diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi
index 68e825a..3484275 100644
--- a/arch/arm/boot/dts/sun7i-a20.dtsi
+++ b/arch/arm/boot/dts/sun7i-a20.dtsi
@@ -531,6 +531,13 @@
 			interrupts = <0 24 1>;
 		};
 
+		lradc: lradc@01c22800 {
+			compatible = "allwinner,sun4i-lradc-keys";
+			reg = <0x01c22800 0x100>;
+			interrupts = <0 31 4>;
+			status = "disabled";
+		};
+
 		sid: eeprom@01c23800 {
 			compatible = "allwinner,sun7i-a20-sid";
 			reg = <0x01c23800 0x200>;
-- 
1.8.4.2

[PATCH 4/4] ARM: dts: sun7i: Add lradc node

[Hans de Goede]

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts | 7 +++++++
 arch/arm/boot/dts/sun7i-a20.dtsi                | 7 +++++++
 2 files changed, 14 insertions(+)

diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
index 0ee2641..dcf9db7 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
+++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
@@ -86,6 +86,13 @@
 			};
 		};
 
+		lradc: lradc at 01c22800 {
+			allwinner,chan0-step = <200>;
+			/* VOLUMEUP VOLUMEDOWN MENU SEARCH HOME ESC ENTER */
+			allwinner,chan0-keycodes = <115 114 139 217 102 1 28>;
+			status = "okay";
+		};
+
 		uart0: serial at 01c28000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart0_pins_a>;
diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi
index 68e825a..3484275 100644
--- a/arch/arm/boot/dts/sun7i-a20.dtsi
+++ b/arch/arm/boot/dts/sun7i-a20.dtsi
@@ -531,6 +531,13 @@
 			interrupts = <0 24 1>;
 		};
 
+		lradc: lradc at 01c22800 {
+			compatible = "allwinner,sun4i-lradc-keys";
+			reg = <0x01c22800 0x100>;
+			interrupts = <0 31 4>;
+			status = "disabled";
+		};
+
 		sid: eeprom at 01c23800 {
 			compatible = "allwinner,sun7i-a20-sid";
 			reg = <0x01c23800 0x200>;
-- 
1.8.4.2