From: zhuyj <zyjzyj2000@gmail.com>
To: linux-wireless@vger.kernel.org
Cc: zhuyj <zyjzyj2000@gmail.com>, "Liu, Bopeng" <Bopeng.Liu@windriver.com>
Subject: 802.11a is supported in AP mode or not?
Date: Wed, 22 Jan 2014 17:50:54 +0800 [thread overview]
Message-ID: <52DF947E.40800@gmail.com> (raw)
Hi, maintainers
I made tests on ubuntu 13.10. I followed these steps.
From the following logs, we can see 802.11a is not supported in channel
list.
I want to know whether 802.11a supports this or not? Or 802.11a is not
used in this?
Chip is 6205. lspci -vvv is as below.
Thanks a lot.
Zhu Yanjun
1. installed ubuntu 13.10 client
2. git clone
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git linux-git
3. apt-get install kernel-package
4. make-kpkg --initrd --append-to-version=-test-iwlwifi kernel_image
kernel-headers
5. dpkg -i linux-headers-
dpkg -i linux-images-
6.reboot ubuntu 13.10
7. $ vi /etc/hostapd.conf
interface=wlan0
driver=nl80211
logger_syslog=-1
logger_syslog_level=2
logger_stdout=-1
logger_stdout_level=2
dump_file=/tmp/hostapd.dump
ctrl_interface=/var/run/hostapd
ctrl_interface_group=0
ssid=test
country_code=US
hw_mode=a
channel=2
beacon_int=100
dtim_period=2
max_num_sta=255
rts_threshold=2347
fragm_threshold=2346
macaddr_acl=0
auth_algs=3
ignore_broadcast_ssid=0
wmm_enabled=1
wmm_ac_bk_cwmin=4
wmm_ac_bk_cwmax=10
wmm_ac_bk_aifs=7
wmm_ac_bk_txop_limit=0
wmm_ac_bk_acm=0
wmm_ac_be_aifs=3
wmm_ac_be_cwmin=4
wmm_ac_be_cwmax=10
wmm_ac_be_txop_limit=0
wmm_ac_be_acm=0
wmm_ac_vi_aifs=2
wmm_ac_vi_cwmin=3
wmm_ac_vi_cwmax=4
wmm_ac_vi_txop_limit=94
wmm_ac_vi_acm=0
wmm_ac_vo_aifs=2
wmm_ac_vo_cwmin=2
wmm_ac_vo_cwmax=3
wmm_ac_vo_txop_limit=47
wmm_ac_vo_acm=0
eap_server=0
wpa=2
wpa_passphrase=12345678
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP CCMP
wpa_group_rekey=600
wpa_gmk_rekey=86400
8. hostapd -B /etc/hostapd.conf -dd
random: Trying to read entropy from /dev/random
Configuration file: /etc/hostapd.conf
ctrl_interface_group=0
nl80211: interface wlan0 in phy phy0
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
nl80211: Using driver-based off-channel TX
nl80211: Register frame command failed (type=208): ret=-114 (Operation
already in progress)
nl80211: Register frame match - hexdump(len=2): 04 0a
nl80211: Failed to register Action frame processing - ignore for now
nl80211: Add own interface ifindex 3
nl80211: Set mode ifindex 3 iftype 3 (AP)
nl80211: Create interface iftype 6 (MONITOR)
nl80211: New interface mon.wlan0 created: ifindex=4
nl80211: Add own interface ifindex 4
BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
nl80211: Regulatory information - country=00
nl80211: 2402-2472 @ 40 MHz
nl80211: 2457-2482 @ 40 MHz
nl80211: 2474-2494 @ 20 MHz
nl80211: 5170-5250 @ 40 MHz
nl80211: 5735-5835 @ 40 MHz
nl80211: Added 802.11b mode based on 802.11g information
Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=15 dBm
Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=15 dBm
Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=15 dBm
wlan0: IEEE 802.11 Configured channel (1) not found from the channel
list of current mode (2) IEEE 802.11a
wlan0: IEEE 802.11 Hardware does not support configured channel
Could not select hw_mode and channel. (-4)
wlan0: Unable to setup interface.
Flushing old station entries
Deauthenticate all stations
rmdir[ctrl_interface]: No such file or directory
nl80211: Remove interface ifindex=4
netlink: Operstate: linkmode=0, operstate=6
nl80211: Set mode ifindex 3 iftype 2 (STATION)
lspci -vvv
01:00.0 Network controller: Intel Corporation Centrino Advanced-N 6205
[Taylor Peak] (rev 34)
Subsystem: Intel Corporation Centrino Advanced-N 6205 AGN
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 45
Region 0: Memory at f7500000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee003d8 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<512ns, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0 <4us, L1 <32us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number a0-88-b4-ff-ff-70-91-20
Kernel driver in use: iwlwifi
next reply other threads:[~2014-01-22 9:51 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-01-22 9:50 zhuyj [this message]
2014-01-22 10:33 ` 802.11a is supported in AP mode or not? zhuyj
2014-01-22 10:47 ` Liu, Bopeng
2014-01-22 14:51 ` Pat Erley
2014-01-22 21:20 ` Krishna Chaitanya
2014-01-23 2:00 ` Liu, Bopeng
2014-01-23 6:15 ` Krishna Chaitanya
2014-01-23 6:37 ` Liu, Bopeng
2014-01-23 6:44 ` zhuyj
2014-01-23 8:23 ` Emmanuel Grumbach
2014-01-23 8:36 ` Liu, Bopeng
2014-01-23 8:41 ` Liu, Bopeng
2014-01-23 8:50 ` zhuyj
2014-01-23 8:57 ` Krishna Chaitanya
2014-01-23 8:59 ` Liu, Bopeng
2014-01-23 9:04 ` Krishna Chaitanya
2014-01-23 9:07 ` Liu, Bopeng
2014-01-23 9:20 ` Liu, Bopeng
2014-01-23 9:21 ` Liu, Bopeng
2014-01-23 9:27 ` Emmanuel Grumbach
2014-01-23 9:29 ` Krishna Chaitanya
2014-01-23 9:34 ` Liu, Bopeng
2014-01-23 9:36 ` Liu, Bopeng
2014-01-23 9:49 ` Emmanuel Grumbach
2014-01-24 5:27 ` Liu, Bopeng
2014-01-27 21:21 ` Anand Moon
2014-01-27 21:59 ` Anand Moon
2014-01-24 6:26 ` Liu, Bopeng
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=52DF947E.40800@gmail.com \
--to=zyjzyj2000@gmail.com \
--cc=Bopeng.Liu@windriver.com \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.