* [meta-fsl-arm-extra][PATCH v5 2/3] linux-cubox-i: add customized kernel
2014-01-29 0:03 [meta-fsl-arm-extra][PATCH v5 1/3] u-boot-cubox-i: add u-boot fork for cubox-i machines Carlos Rafael Giani
@ 2014-01-29 0:03 ` Carlos Rafael Giani
2014-01-29 0:03 ` [meta-fsl-arm-extra][PATCH v5 3/3] cubox-i: add machine config Carlos Rafael Giani
2014-01-29 11:43 ` [meta-fsl-arm-extra][PATCH v5 1/3] u-boot-cubox-i: add u-boot fork for cubox-i machines Daiane Angolini
2 siblings, 0 replies; 5+ messages in thread
From: Carlos Rafael Giani @ 2014-01-29 0:03 UTC (permalink / raw)
To: meta-freescale
This kernel is based on linux-imx 3.0.35, and adds patches for
CuBox-i and HummingBoard support
Signed-off-by: Carlos Rafael Giani <dv@pseudoterminal.org>
---
...fix-memset-related-crashes-caused-by-rece.patch | 259 +++++++++++++++
.../0003-ARM-7670-1-fix-the-memset-fix.patch | 87 +++++
...6-Fix-build-break-when-CONFIG_CLK_DEBUG-i.patch | 43 +++
...0005-ENGR00271359-Add-Multi-touch-support.patch | 98 ++++++
.../0006-Add-support-for-DVI-monitors.patch | 227 +++++++++++++
...6-board-mx6q_sabresd-Register-SDHC3-first.patch | 38 +++
.../linux/linux-cubox-i-3.0.35/defconfig | 366 +++++++++++++++++++++
...-Rename-mxcfb_epdc_kernel.h-to-mxc_epdc.h.patch | 143 ++++++++
.../fix-install-breakage-for-fw-images.patch | 32 ++
.../mxc_hdmi-dont-require-cea-mode.patch | 25 ++
recipes-kernel/linux/linux-cubox-i_3.0.35.bb | 23 ++
11 files changed, 1341 insertions(+)
create mode 100644 recipes-kernel/linux/linux-cubox-i-3.0.35/0002-ARM-7668-1-fix-memset-related-crashes-caused-by-rece.patch
create mode 100644 recipes-kernel/linux/linux-cubox-i-3.0.35/0003-ARM-7670-1-fix-the-memset-fix.patch
create mode 100644 recipes-kernel/linux/linux-cubox-i-3.0.35/0004-ENGR00271136-Fix-build-break-when-CONFIG_CLK_DEBUG-i.patch
create mode 100644 recipes-kernel/linux/linux-cubox-i-3.0.35/0005-ENGR00271359-Add-Multi-touch-support.patch
create mode 100644 recipes-kernel/linux/linux-cubox-i-3.0.35/0006-Add-support-for-DVI-monitors.patch
create mode 100644 recipes-kernel/linux/linux-cubox-i-3.0.35/0007-ARM-mach-mx6-board-mx6q_sabresd-Register-SDHC3-first.patch
create mode 100644 recipes-kernel/linux/linux-cubox-i-3.0.35/defconfig
create mode 100644 recipes-kernel/linux/linux-cubox-i-3.0.35/epdc-Rename-mxcfb_epdc_kernel.h-to-mxc_epdc.h.patch
create mode 100644 recipes-kernel/linux/linux-cubox-i-3.0.35/fix-install-breakage-for-fw-images.patch
create mode 100644 recipes-kernel/linux/linux-cubox-i-3.0.35/mxc_hdmi-dont-require-cea-mode.patch
create mode 100644 recipes-kernel/linux/linux-cubox-i_3.0.35.bb
diff --git a/recipes-kernel/linux/linux-cubox-i-3.0.35/0002-ARM-7668-1-fix-memset-related-crashes-caused-by-rece.patch b/recipes-kernel/linux/linux-cubox-i-3.0.35/0002-ARM-7668-1-fix-memset-related-crashes-caused-by-rece.patch
new file mode 100644
index 0000000..4c31e74
--- /dev/null
+++ b/recipes-kernel/linux/linux-cubox-i-3.0.35/0002-ARM-7668-1-fix-memset-related-crashes-caused-by-rece.patch
@@ -0,0 +1,259 @@
+From 2235b85f1c76d98b5f1e160cbd0a61a84c15e125 Mon Sep 17 00:00:00 2001
+From: Ivan Djelic <ivan.djelic@parrot.com>
+Date: Wed, 6 Mar 2013 20:09:27 +0100
+Subject: [PATCH] ARM: 7668/1: fix memset-related crashes caused by recent GCC
+ (4.7.2) optimizations
+Organization: O.S. Systems Software LTDA.
+
+Recent GCC versions (e.g. GCC-4.7.2) perform optimizations based on
+assumptions about the implementation of memset and similar functions.
+The current ARM optimized memset code does not return the value of
+its first argument, as is usually expected from standard implementations.
+
+For instance in the following function:
+
+void debug_mutex_lock_common(struct mutex *lock, struct mutex_waiter *waiter)
+{
+ memset(waiter, MUTEX_DEBUG_INIT, sizeof(*waiter));
+ waiter->magic = waiter;
+ INIT_LIST_HEAD(&waiter->list);
+}
+
+compiled as:
+
+800554d0 <debug_mutex_lock_common>:
+800554d0: e92d4008 push {r3, lr}
+800554d4: e1a00001 mov r0, r1
+800554d8: e3a02010 mov r2, #16 ; 0x10
+800554dc: e3a01011 mov r1, #17 ; 0x11
+800554e0: eb04426e bl 80165ea0 <memset>
+800554e4: e1a03000 mov r3, r0
+800554e8: e583000c str r0, [r3, #12]
+800554ec: e5830000 str r0, [r3]
+800554f0: e5830004 str r0, [r3, #4]
+800554f4: e8bd8008 pop {r3, pc}
+
+GCC assumes memset returns the value of pointer 'waiter' in register r0; causing
+register/memory corruptions.
+
+This patch fixes the return value of the assembly version of memset.
+It adds a 'mov' instruction and merges an additional load+store into
+existing load/store instructions.
+For ease of review, here is a breakdown of the patch into 4 simple steps:
+
+Step 1
+======
+Perform the following substitutions:
+ip -> r8, then
+r0 -> ip,
+and insert 'mov ip, r0' as the first statement of the function.
+At this point, we have a memset() implementation returning the proper result,
+but corrupting r8 on some paths (the ones that were using ip).
+
+Step 2
+======
+Make sure r8 is saved and restored when (! CALGN(1)+0) == 1:
+
+save r8:
+- str lr, [sp, #-4]!
++ stmfd sp!, {r8, lr}
+
+and restore r8 on both exit paths:
+- ldmeqfd sp!, {pc} @ Now <64 bytes to go.
++ ldmeqfd sp!, {r8, pc} @ Now <64 bytes to go.
+(...)
+ tst r2, #16
+ stmneia ip!, {r1, r3, r8, lr}
+- ldr lr, [sp], #4
++ ldmfd sp!, {r8, lr}
+
+Step 3
+======
+Make sure r8 is saved and restored when (! CALGN(1)+0) == 0:
+
+save r8:
+- stmfd sp!, {r4-r7, lr}
++ stmfd sp!, {r4-r8, lr}
+
+and restore r8 on both exit paths:
+ bgt 3b
+- ldmeqfd sp!, {r4-r7, pc}
++ ldmeqfd sp!, {r4-r8, pc}
+(...)
+ tst r2, #16
+ stmneia ip!, {r4-r7}
+- ldmfd sp!, {r4-r7, lr}
++ ldmfd sp!, {r4-r8, lr}
+
+Step 4
+======
+Rewrite register list "r4-r7, r8" as "r4-r8".
+
+Upstream-Status: Pending
+
+Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
+Reviewed-by: Nicolas Pitre <nico@linaro.org>
+Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
+Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
+(cherry picked from commit 455bd4c430b0c0a361f38e8658a0d6cb469942b5)
+---
+ arch/arm/lib/memset.S | 85 ++++++++++++++++++++++++++-------------------------
+ 1 file changed, 44 insertions(+), 41 deletions(-)
+
+diff --git a/arch/arm/lib/memset.S b/arch/arm/lib/memset.S
+index 650d592..d912e73 100644
+--- a/arch/arm/lib/memset.S
++++ b/arch/arm/lib/memset.S
+@@ -19,9 +19,9 @@
+ 1: subs r2, r2, #4 @ 1 do we have enough
+ blt 5f @ 1 bytes to align with?
+ cmp r3, #2 @ 1
+- strltb r1, [r0], #1 @ 1
+- strleb r1, [r0], #1 @ 1
+- strb r1, [r0], #1 @ 1
++ strltb r1, [ip], #1 @ 1
++ strleb r1, [ip], #1 @ 1
++ strb r1, [ip], #1 @ 1
+ add r2, r2, r3 @ 1 (r2 = r2 - (4 - r3))
+ /*
+ * The pointer is now aligned and the length is adjusted. Try doing the
+@@ -29,10 +29,14 @@
+ */
+
+ ENTRY(memset)
+- ands r3, r0, #3 @ 1 unaligned?
++/*
++ * Preserve the contents of r0 for the return value.
++ */
++ mov ip, r0
++ ands r3, ip, #3 @ 1 unaligned?
+ bne 1b @ 1
+ /*
+- * we know that the pointer in r0 is aligned to a word boundary.
++ * we know that the pointer in ip is aligned to a word boundary.
+ */
+ orr r1, r1, r1, lsl #8
+ orr r1, r1, r1, lsl #16
+@@ -43,29 +47,28 @@ ENTRY(memset)
+ #if ! CALGN(1)+0
+
+ /*
+- * We need an extra register for this loop - save the return address and
+- * use the LR
++ * We need 2 extra registers for this loop - use r8 and the LR
+ */
+- str lr, [sp, #-4]!
+- mov ip, r1
++ stmfd sp!, {r8, lr}
++ mov r8, r1
+ mov lr, r1
+
+ 2: subs r2, r2, #64
+- stmgeia r0!, {r1, r3, ip, lr} @ 64 bytes at a time.
+- stmgeia r0!, {r1, r3, ip, lr}
+- stmgeia r0!, {r1, r3, ip, lr}
+- stmgeia r0!, {r1, r3, ip, lr}
++ stmgeia ip!, {r1, r3, r8, lr} @ 64 bytes at a time.
++ stmgeia ip!, {r1, r3, r8, lr}
++ stmgeia ip!, {r1, r3, r8, lr}
++ stmgeia ip!, {r1, r3, r8, lr}
+ bgt 2b
+- ldmeqfd sp!, {pc} @ Now <64 bytes to go.
++ ldmeqfd sp!, {r8, pc} @ Now <64 bytes to go.
+ /*
+ * No need to correct the count; we're only testing bits from now on
+ */
+ tst r2, #32
+- stmneia r0!, {r1, r3, ip, lr}
+- stmneia r0!, {r1, r3, ip, lr}
++ stmneia ip!, {r1, r3, r8, lr}
++ stmneia ip!, {r1, r3, r8, lr}
+ tst r2, #16
+- stmneia r0!, {r1, r3, ip, lr}
+- ldr lr, [sp], #4
++ stmneia ip!, {r1, r3, r8, lr}
++ ldmfd sp!, {r8, lr}
+
+ #else
+
+@@ -74,54 +77,54 @@ ENTRY(memset)
+ * whole cache lines at once.
+ */
+
+- stmfd sp!, {r4-r7, lr}
++ stmfd sp!, {r4-r8, lr}
+ mov r4, r1
+ mov r5, r1
+ mov r6, r1
+ mov r7, r1
+- mov ip, r1
++ mov r8, r1
+ mov lr, r1
+
+ cmp r2, #96
+- tstgt r0, #31
++ tstgt ip, #31
+ ble 3f
+
+- and ip, r0, #31
+- rsb ip, ip, #32
+- sub r2, r2, ip
+- movs ip, ip, lsl #(32 - 4)
+- stmcsia r0!, {r4, r5, r6, r7}
+- stmmiia r0!, {r4, r5}
+- tst ip, #(1 << 30)
+- mov ip, r1
+- strne r1, [r0], #4
++ and r8, ip, #31
++ rsb r8, r8, #32
++ sub r2, r2, r8
++ movs r8, r8, lsl #(32 - 4)
++ stmcsia ip!, {r4, r5, r6, r7}
++ stmmiia ip!, {r4, r5}
++ tst r8, #(1 << 30)
++ mov r8, r1
++ strne r1, [ip], #4
+
+ 3: subs r2, r2, #64
+- stmgeia r0!, {r1, r3-r7, ip, lr}
+- stmgeia r0!, {r1, r3-r7, ip, lr}
++ stmgeia ip!, {r1, r3-r8, lr}
++ stmgeia ip!, {r1, r3-r8, lr}
+ bgt 3b
+- ldmeqfd sp!, {r4-r7, pc}
++ ldmeqfd sp!, {r4-r8, pc}
+
+ tst r2, #32
+- stmneia r0!, {r1, r3-r7, ip, lr}
++ stmneia ip!, {r1, r3-r8, lr}
+ tst r2, #16
+- stmneia r0!, {r4-r7}
+- ldmfd sp!, {r4-r7, lr}
++ stmneia ip!, {r4-r7}
++ ldmfd sp!, {r4-r8, lr}
+
+ #endif
+
+ 4: tst r2, #8
+- stmneia r0!, {r1, r3}
++ stmneia ip!, {r1, r3}
+ tst r2, #4
+- strne r1, [r0], #4
++ strne r1, [ip], #4
+ /*
+ * When we get here, we've got less than 4 bytes to zero. We
+ * may have an unaligned pointer as well.
+ */
+ 5: tst r2, #2
+- strneb r1, [r0], #1
+- strneb r1, [r0], #1
++ strneb r1, [ip], #1
++ strneb r1, [ip], #1
+ tst r2, #1
+- strneb r1, [r0], #1
++ strneb r1, [ip], #1
+ mov pc, lr
+ ENDPROC(memset)
+--
+1.8.4.rc3
+
diff --git a/recipes-kernel/linux/linux-cubox-i-3.0.35/0003-ARM-7670-1-fix-the-memset-fix.patch b/recipes-kernel/linux/linux-cubox-i-3.0.35/0003-ARM-7670-1-fix-the-memset-fix.patch
new file mode 100644
index 0000000..b8d6f53
--- /dev/null
+++ b/recipes-kernel/linux/linux-cubox-i-3.0.35/0003-ARM-7670-1-fix-the-memset-fix.patch
@@ -0,0 +1,87 @@
+From 2ba23fa6c4128febaaf57fe184420a7111caa237 Mon Sep 17 00:00:00 2001
+From: Nicolas Pitre <nicolas.pitre@linaro.org>
+Date: Tue, 12 Mar 2013 13:00:42 +0100
+Subject: [PATCH] ARM: 7670/1: fix the memset fix
+Organization: O.S. Systems Software LTDA.
+
+Commit 455bd4c430b0 ("ARM: 7668/1: fix memset-related crashes caused by
+recent GCC (4.7.2) optimizations") attempted to fix a compliance issue
+with the memset return value. However the memset itself became broken
+by that patch for misaligned pointers.
+
+This fixes the above by branching over the entry code from the
+misaligned fixup code to avoid reloading the original pointer.
+
+Also, because the function entry alignment is wrong in the Thumb mode
+compilation, that fixup code is moved to the end.
+
+While at it, the entry instructions are slightly reworked to help dual
+issue pipelines.
+
+Upstream-Status: Pending
+
+Signed-off-by: Nicolas Pitre <nico@linaro.org>
+Tested-by: Alexander Holler <holler@ahsoftware.de>
+Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
+(cherry picked from commit 418df63adac56841ef6b0f1fcf435bc64d4ed177)
+---
+ arch/arm/lib/memset.S | 33 +++++++++++++--------------------
+ 1 file changed, 13 insertions(+), 20 deletions(-)
+
+diff --git a/arch/arm/lib/memset.S b/arch/arm/lib/memset.S
+index d912e73..94b0650 100644
+--- a/arch/arm/lib/memset.S
++++ b/arch/arm/lib/memset.S
+@@ -14,31 +14,15 @@
+
+ .text
+ .align 5
+- .word 0
+-
+-1: subs r2, r2, #4 @ 1 do we have enough
+- blt 5f @ 1 bytes to align with?
+- cmp r3, #2 @ 1
+- strltb r1, [ip], #1 @ 1
+- strleb r1, [ip], #1 @ 1
+- strb r1, [ip], #1 @ 1
+- add r2, r2, r3 @ 1 (r2 = r2 - (4 - r3))
+-/*
+- * The pointer is now aligned and the length is adjusted. Try doing the
+- * memset again.
+- */
+
+ ENTRY(memset)
+-/*
+- * Preserve the contents of r0 for the return value.
+- */
+- mov ip, r0
+- ands r3, ip, #3 @ 1 unaligned?
+- bne 1b @ 1
++ ands r3, r0, #3 @ 1 unaligned?
++ mov ip, r0 @ preserve r0 as return value
++ bne 6f @ 1
+ /*
+ * we know that the pointer in ip is aligned to a word boundary.
+ */
+- orr r1, r1, r1, lsl #8
++1: orr r1, r1, r1, lsl #8
+ orr r1, r1, r1, lsl #16
+ mov r3, r1
+ cmp r2, #16
+@@ -127,4 +111,13 @@ ENTRY(memset)
+ tst r2, #1
+ strneb r1, [ip], #1
+ mov pc, lr
++
++6: subs r2, r2, #4 @ 1 do we have enough
++ blt 5b @ 1 bytes to align with?
++ cmp r3, #2 @ 1
++ strltb r1, [ip], #1 @ 1
++ strleb r1, [ip], #1 @ 1
++ strb r1, [ip], #1 @ 1
++ add r2, r2, r3 @ 1 (r2 = r2 - (4 - r3))
++ b 1b
+ ENDPROC(memset)
+--
+1.8.4.rc3
+
diff --git a/recipes-kernel/linux/linux-cubox-i-3.0.35/0004-ENGR00271136-Fix-build-break-when-CONFIG_CLK_DEBUG-i.patch b/recipes-kernel/linux/linux-cubox-i-3.0.35/0004-ENGR00271136-Fix-build-break-when-CONFIG_CLK_DEBUG-i.patch
new file mode 100644
index 0000000..7316351
--- /dev/null
+++ b/recipes-kernel/linux/linux-cubox-i-3.0.35/0004-ENGR00271136-Fix-build-break-when-CONFIG_CLK_DEBUG-i.patch
@@ -0,0 +1,43 @@
+From d8601292ae25e0af47aa4486055221ab44113f0e Mon Sep 17 00:00:00 2001
+From: Mahesh Mahadevan <Mahesh.Mahadevan@freescale.com>
+Date: Mon, 15 Jul 2013 15:34:54 -0500
+Subject: [PATCH] ENGR00271136 Fix build break when CONFIG_CLK_DEBUG is
+ disabled
+Organization: O.S. Systems Software LTDA.
+
+clk structure member name is defined only when CONFIG_CLK_DEBUG is enabled.
+Hence need to encapsulate the code with this config.
+
+Patch received from imx community:
+https://community.freescale.com/thread/308482
+
+Upstream-Status: Pending
+
+Signed-off-by: xiongweihuang
+Signed-off-by: Mahesh Mahadevan <Mahesh.Mahadevan@freescale.com>
+---
+ arch/arm/plat-mxc/clock.c | 4 ++--
+ 1 file changed, 2 insertions(+), 2 deletions(-)
+
+diff --git a/arch/arm/plat-mxc/clock.c b/arch/arm/plat-mxc/clock.c
+index 93347eb..1aa2664 100755
+--- a/arch/arm/plat-mxc/clock.c
++++ b/arch/arm/plat-mxc/clock.c
+@@ -58,12 +58,12 @@ static void __clk_disable(struct clk *clk)
+ {
+ if (clk == NULL || IS_ERR(clk))
+ return;
+-
++#ifdef CONFIG_CLK_DEBUG
+ if (!clk->usecount) {
+ WARN(1, "clock enable/disable mismatch! clk %s\n", clk->name);
+ return;
+ }
+-
++#endif
+ if (!(--clk->usecount)) {
+ if (clk->disable)
+ clk->disable(clk);
+--
+1.8.4.rc3
+
diff --git a/recipes-kernel/linux/linux-cubox-i-3.0.35/0005-ENGR00271359-Add-Multi-touch-support.patch b/recipes-kernel/linux/linux-cubox-i-3.0.35/0005-ENGR00271359-Add-Multi-touch-support.patch
new file mode 100644
index 0000000..cb20198
--- /dev/null
+++ b/recipes-kernel/linux/linux-cubox-i-3.0.35/0005-ENGR00271359-Add-Multi-touch-support.patch
@@ -0,0 +1,98 @@
+From 538f4bb2f7a51f267395550a5be9f0ab2e426712 Mon Sep 17 00:00:00 2001
+From: Erik Boto <erik.boto@pelagicore.com>
+Date: Tue, 16 Jul 2013 12:06:05 -0500
+Subject: [PATCH] ENGR00271359 Add Multi-touch support
+Organization: O.S. Systems Software LTDA.
+
+The previous behavior of the driver did not work properly with Qt5
+QtQuick multi touch-point gestures, due to how touch-points are
+reported when removing a touch-point. My interpretation of the
+available documentation [1] was that the driver should report all
+touch-points between SYN_REPORTs, but it is not explicitly stated so.
+I've found another mail-thread [2] where the creator of the protocol
+states:
+
+"The protocol defines a generic way of sending a variable amount of
+contacts. The contact count is obtained by counting the number of
+non-empty finger packets between SYN_REPORT events."-Henrik Rydberg
+
+I think this verifies my assumption that all touch-points should be
+reported between SYN_REPORTs, otherwise it can not be used to obtain
+the count.
+
+[1] https://www.kernel.org/doc/Documentation/input/multi-touch-protocol.txt
+[2] http://lists.x.org/archives/xorg-devel/2010-March/006466.html
+
+Upstream-Status: Pending
+
+Signed-off-by: Erik Boto <erik.boto@pelagicore.com>
+Signed-off-by: Mahesh Mahadevan <Mahesh.Mahadevan@freescale.com>
+(cherry picked from commit 7cba001c5a502680f6dbf902821726779a9c9287)
+---
+ drivers/input/touchscreen/egalax_ts.c | 36 +++++++++++++++++------------------
+ 1 file changed, 18 insertions(+), 18 deletions(-)
+
+diff --git a/drivers/input/touchscreen/egalax_ts.c b/drivers/input/touchscreen/egalax_ts.c
+index 0b6cde7..271f820 100644
+--- a/drivers/input/touchscreen/egalax_ts.c
++++ b/drivers/input/touchscreen/egalax_ts.c
+@@ -133,7 +133,6 @@ retry:
+ }
+
+ if (down) {
+- /* should also report old pointers */
+ events[id].valid = valid;
+ events[id].status = down;
+ events[id].x = x;
+@@ -144,23 +143,6 @@ retry:
+ input_report_abs(input_dev, ABS_Y, y);
+ input_event(data->input_dev, EV_KEY, BTN_TOUCH, 1);
+ input_report_abs(input_dev, ABS_PRESSURE, 1);
+-#else
+- for (i = 0; i < MAX_SUPPORT_POINTS; i++) {
+- if (!events[i].valid)
+- continue;
+- dev_dbg(&client->dev, "report id:%d valid:%d x:%d y:%d",
+- i, valid, x, y);
+-
+- input_report_abs(input_dev,
+- ABS_MT_TRACKING_ID, i);
+- input_report_abs(input_dev,
+- ABS_MT_TOUCH_MAJOR, 1);
+- input_report_abs(input_dev,
+- ABS_MT_POSITION_X, events[i].x);
+- input_report_abs(input_dev,
+- ABS_MT_POSITION_Y, events[i].y);
+- input_mt_sync(input_dev);
+- }
+ #endif
+ } else {
+ dev_dbg(&client->dev, "release id:%d\n", id);
+@@ -176,6 +158,24 @@ retry:
+ #endif
+ }
+
++#ifndef CONFIG_TOUCHSCREEN_EGALAX_SINGLE_TOUCH
++ /* report all pointers */
++ for (i = 0; i < MAX_SUPPORT_POINTS; i++) {
++ if (!events[i].valid)
++ continue;
++ dev_dbg(&client->dev, "report id:%d valid:%d x:%d y:%d",
++ i, valid, x, y);
++ input_report_abs(input_dev,
++ ABS_MT_TRACKING_ID, i);
++ input_report_abs(input_dev,
++ ABS_MT_TOUCH_MAJOR, 1);
++ input_report_abs(input_dev,
++ ABS_MT_POSITION_X, events[i].x);
++ input_report_abs(input_dev,
++ ABS_MT_POSITION_Y, events[i].y);
++ input_mt_sync(input_dev);
++ }
++#endif
+ input_sync(input_dev);
+ return IRQ_HANDLED;
+ }
+--
+1.8.4.rc3
+
diff --git a/recipes-kernel/linux/linux-cubox-i-3.0.35/0006-Add-support-for-DVI-monitors.patch b/recipes-kernel/linux/linux-cubox-i-3.0.35/0006-Add-support-for-DVI-monitors.patch
new file mode 100644
index 0000000..00a6b5c
--- /dev/null
+++ b/recipes-kernel/linux/linux-cubox-i-3.0.35/0006-Add-support-for-DVI-monitors.patch
@@ -0,0 +1,227 @@
+From 3e6441d113f72b412081a2c87f39011e4c253a35 Mon Sep 17 00:00:00 2001
+From: Robert Winkler <robert.winkler@boundarydevices.com>
+Date: Fri, 19 Jul 2013 19:00:41 -0700
+Subject: [PATCH] Add support for DVI monitors
+Organization: O.S. Systems Software LTDA.
+
+Upstream-Status: Pending
+
+Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
+---
+ arch/arm/plat-mxc/include/mach/mxc_hdmi.h | 7 +++
+ drivers/video/mxc_hdmi.c | 98 +++++++++++++------------------
+ 2 files changed, 49 insertions(+), 56 deletions(-)
+
+diff --git a/arch/arm/plat-mxc/include/mach/mxc_hdmi.h b/arch/arm/plat-mxc/include/mach/mxc_hdmi.h
+index 94f7638..af59c62 100644
+--- a/arch/arm/plat-mxc/include/mach/mxc_hdmi.h
++++ b/arch/arm/plat-mxc/include/mach/mxc_hdmi.h
+@@ -605,6 +605,10 @@ enum {
+ HDMI_IH_MUTE_PHY_STAT0_TX_PHY_LOCK = 0x2,
+ HDMI_IH_MUTE_PHY_STAT0_HPD = 0x1,
+
++/* IH and IH_MUTE convenience macro RX_SENSE | HPD*/
++ HDMI_DVI_IH_STAT = 0x3D,
++
++
+ /* IH_AHBDMAAUD_STAT0 field values */
+ HDMI_IH_AHBDMAAUD_STAT0_ERROR = 0x20,
+ HDMI_IH_AHBDMAAUD_STAT0_LOST = 0x10,
+@@ -903,6 +907,9 @@ enum {
+ HDMI_PHY_HPD = 0x02,
+ HDMI_PHY_TX_PHY_LOCK = 0x01,
+
++/* HDMI STAT convenience RX_SENSE | HPD */
++ HDMI_DVI_STAT = 0xF2,
++
+ /* PHY_I2CM_SLAVE_ADDR field values */
+ HDMI_PHY_I2CM_SLAVE_ADDR_PHY_GEN2 = 0x69,
+ HDMI_PHY_I2CM_SLAVE_ADDR_HEAC_PHY = 0x49,
+diff --git a/drivers/video/mxc_hdmi.c b/drivers/video/mxc_hdmi.c
+index c5069aa..544f352 100644
+--- a/drivers/video/mxc_hdmi.c
++++ b/drivers/video/mxc_hdmi.c
+@@ -180,7 +180,6 @@ struct mxc_hdmi {
+ bool dft_mode_set;
+ char *dft_mode_str;
+ int default_bpp;
+- u8 latest_intr_stat;
+ bool irq_enabled;
+ spinlock_t irq_lock;
+ bool phy_enabled;
+@@ -1996,58 +1995,48 @@ static void hotplug_worker(struct work_struct *work)
+ struct delayed_work *delay_work = to_delayed_work(work);
+ struct mxc_hdmi *hdmi =
+ container_of(delay_work, struct mxc_hdmi, hotplug_work);
+- u32 phy_int_stat, phy_int_pol, phy_int_mask;
+- u8 val;
++ u32 hdmi_phy_stat0, hdmi_phy_pol0, hdmi_phy_mask0;
+ unsigned long flags;
+ char event_string[32];
+ char *envp[] = { event_string, NULL };
+
+- phy_int_stat = hdmi->latest_intr_stat;
+- phy_int_pol = hdmi_readb(HDMI_PHY_POL0);
+
+- dev_dbg(&hdmi->pdev->dev, "phy_int_stat=0x%x, phy_int_pol=0x%x\n",
+- phy_int_stat, phy_int_pol);
++ hdmi_phy_stat0 = hdmi_readb(HDMI_PHY_STAT0);
++ hdmi_phy_pol0 = hdmi_readb(HDMI_PHY_POL0);
++
++ dev_dbg(&hdmi->pdev->dev, "hdmi_phy_stat0=0x%x, hdmi_phy_pol0=0x%x\n",
++ hdmi_phy_stat0, hdmi_phy_pol0);
++
++ /* Make HPD intr active low to capture unplug event or
++ * active high to capture plugin event */
++ hdmi_writeb((HDMI_DVI_STAT & ~hdmi_phy_stat0), HDMI_PHY_POL0);
+
+ /* check cable status */
+- if (phy_int_stat & HDMI_IH_PHY_STAT0_HPD) {
+- /* cable connection changes */
+- if (phy_int_pol & HDMI_PHY_HPD) {
+- /* Plugin event */
+- dev_dbg(&hdmi->pdev->dev, "EVENT=plugin\n");
+- mxc_hdmi_cable_connected(hdmi);
+-
+- /* Make HPD intr active low to capture unplug event */
+- val = hdmi_readb(HDMI_PHY_POL0);
+- val &= ~HDMI_PHY_HPD;
+- hdmi_writeb(val, HDMI_PHY_POL0);
+-
+- sprintf(event_string, "EVENT=plugin");
+- kobject_uevent_env(&hdmi->pdev->dev.kobj, KOBJ_CHANGE, envp);
++ if (hdmi_phy_stat0 & HDMI_DVI_STAT) {
++ /* Plugin event */
++ dev_dbg(&hdmi->pdev->dev, "EVENT=plugin\n");
++ mxc_hdmi_cable_connected(hdmi);
++
++ sprintf(event_string, "EVENT=plugin");
++ kobject_uevent_env(&hdmi->pdev->dev.kobj, KOBJ_CHANGE, envp);
+ #ifdef CONFIG_MXC_HDMI_CEC
+- mxc_hdmi_cec_handle(0x80);
++ mxc_hdmi_cec_handle(0x80);
+ #endif
+- hdmi_set_cable_state(1);
+-
+- } else if (!(phy_int_pol & HDMI_PHY_HPD)) {
+- /* Plugout event */
+- dev_dbg(&hdmi->pdev->dev, "EVENT=plugout\n");
+- hdmi_set_cable_state(0);
+- mxc_hdmi_abort_stream();
+- mxc_hdmi_cable_disconnected(hdmi);
++ hdmi_set_cable_state(1);
+
+- /* Make HPD intr active high to capture plugin event */
+- val = hdmi_readb(HDMI_PHY_POL0);
+- val |= HDMI_PHY_HPD;
+- hdmi_writeb(val, HDMI_PHY_POL0);
++ } else {
++ /* Plugout event */
++ dev_dbg(&hdmi->pdev->dev, "EVENT=plugout\n");
++ hdmi_set_cable_state(0);
++ mxc_hdmi_abort_stream();
++ mxc_hdmi_cable_disconnected(hdmi);
+
+- sprintf(event_string, "EVENT=plugout");
+- kobject_uevent_env(&hdmi->pdev->dev.kobj, KOBJ_CHANGE, envp);
++ sprintf(event_string, "EVENT=plugout");
++ kobject_uevent_env(&hdmi->pdev->dev.kobj, KOBJ_CHANGE, envp);
+ #ifdef CONFIG_MXC_HDMI_CEC
+- mxc_hdmi_cec_handle(0x100);
++ mxc_hdmi_cec_handle(0x100);
+ #endif
+
+- } else
+- dev_dbg(&hdmi->pdev->dev, "EVENT=none?\n");
+ }
+
+ /* Lock here to ensure full powerdown sequence
+@@ -2055,12 +2044,12 @@ static void hotplug_worker(struct work_struct *work)
+ spin_lock_irqsave(&hdmi->irq_lock, flags);
+
+ /* Re-enable HPD interrupts */
+- phy_int_mask = hdmi_readb(HDMI_PHY_MASK0);
+- phy_int_mask &= ~HDMI_PHY_HPD;
+- hdmi_writeb(phy_int_mask, HDMI_PHY_MASK0);
++ hdmi_phy_mask0 = hdmi_readb(HDMI_PHY_MASK0);
++ hdmi_phy_mask0 &= ~HDMI_DVI_STAT;
++ hdmi_writeb(hdmi_phy_mask0, HDMI_PHY_MASK0);
+
+ /* Unmute interrupts */
+- hdmi_writeb(~HDMI_IH_MUTE_PHY_STAT0_HPD, HDMI_IH_MUTE_PHY_STAT0);
++ hdmi_writeb(~HDMI_DVI_IH_STAT, HDMI_IH_MUTE_PHY_STAT0);
+
+ if (hdmi_readb(HDMI_IH_FC_STAT2) & HDMI_IH_FC_STAT2_OVERFLOW_MASK)
+ mxc_hdmi_clear_overflow();
+@@ -2086,7 +2075,7 @@ static void hdcp_hdp_worker(struct work_struct *work)
+ static irqreturn_t mxc_hdmi_hotplug(int irq, void *data)
+ {
+ struct mxc_hdmi *hdmi = data;
+- u8 val, intr_stat;
++ u8 val;
+ unsigned long flags;
+
+ spin_lock_irqsave(&hdmi->irq_lock, flags);
+@@ -2108,25 +2097,22 @@ static irqreturn_t mxc_hdmi_hotplug(int irq, void *data)
+ * HDMI registers.
+ */
+ /* Capture status - used in hotplug_worker ISR */
+- intr_stat = hdmi_readb(HDMI_IH_PHY_STAT0);
+-
+- if (intr_stat & HDMI_IH_PHY_STAT0_HPD) {
++ if (hdmi_readb(HDMI_IH_PHY_STAT0) & HDMI_DVI_IH_STAT) {
+
+ dev_dbg(&hdmi->pdev->dev, "Hotplug interrupt received\n");
+- hdmi->latest_intr_stat = intr_stat;
+
+ /* Mute interrupts until handled */
+
+ val = hdmi_readb(HDMI_IH_MUTE_PHY_STAT0);
+- val |= HDMI_IH_MUTE_PHY_STAT0_HPD;
++ val |= HDMI_DVI_IH_STAT;
+ hdmi_writeb(val, HDMI_IH_MUTE_PHY_STAT0);
+
+ val = hdmi_readb(HDMI_PHY_MASK0);
+- val |= HDMI_PHY_HPD;
++ val |= HDMI_DVI_STAT;
+ hdmi_writeb(val, HDMI_PHY_MASK0);
+
+ /* Clear Hotplug interrupts */
+- hdmi_writeb(HDMI_IH_PHY_STAT0_HPD, HDMI_IH_PHY_STAT0);
++ hdmi_writeb(HDMI_DVI_IH_STAT, HDMI_IH_PHY_STAT0);
+
+ schedule_delayed_work(&(hdmi->hotplug_work), msecs_to_jiffies(20));
+ }
+@@ -2282,13 +2268,13 @@ static void mxc_hdmi_fb_registered(struct mxc_hdmi *hdmi)
+ HDMI_PHY_I2CM_CTLINT_ADDR);
+
+ /* enable cable hot plug irq */
+- hdmi_writeb((u8)~HDMI_PHY_HPD, HDMI_PHY_MASK0);
++ hdmi_writeb((u8)~HDMI_DVI_STAT, HDMI_PHY_MASK0);
+
+ /* Clear Hotplug interrupts */
+- hdmi_writeb(HDMI_IH_PHY_STAT0_HPD, HDMI_IH_PHY_STAT0);
++ hdmi_writeb(HDMI_DVI_IH_STAT, HDMI_IH_PHY_STAT0);
+
+ /* Unmute interrupts */
+- hdmi_writeb(~HDMI_IH_MUTE_PHY_STAT0_HPD, HDMI_IH_MUTE_PHY_STAT0);
++ hdmi_writeb(~HDMI_DVI_IH_STAT, HDMI_IH_MUTE_PHY_STAT0);
+
+ hdmi->fb_reg = true;
+
+@@ -2522,10 +2508,10 @@ static int mxc_hdmi_disp_init(struct mxc_dispdrv_handle *disp,
+
+ /* Configure registers related to HDMI interrupt
+ * generation before registering IRQ. */
+- hdmi_writeb(HDMI_PHY_HPD, HDMI_PHY_POL0);
++ hdmi_writeb(HDMI_DVI_STAT, HDMI_PHY_POL0);
+
+ /* Clear Hotplug interrupts */
+- hdmi_writeb(HDMI_IH_PHY_STAT0_HPD, HDMI_IH_PHY_STAT0);
++ hdmi_writeb(HDMI_DVI_IH_STAT, HDMI_IH_PHY_STAT0);
+
+ hdmi->nb.notifier_call = mxc_hdmi_fb_event;
+ ret = fb_register_client(&hdmi->nb);
+--
+1.8.4.rc3
+
diff --git a/recipes-kernel/linux/linux-cubox-i-3.0.35/0007-ARM-mach-mx6-board-mx6q_sabresd-Register-SDHC3-first.patch b/recipes-kernel/linux/linux-cubox-i-3.0.35/0007-ARM-mach-mx6-board-mx6q_sabresd-Register-SDHC3-first.patch
new file mode 100644
index 0000000..d02aa40
--- /dev/null
+++ b/recipes-kernel/linux/linux-cubox-i-3.0.35/0007-ARM-mach-mx6-board-mx6q_sabresd-Register-SDHC3-first.patch
@@ -0,0 +1,38 @@
+From cd31abbe08372fa870fac78ae845edd4859f8835 Mon Sep 17 00:00:00 2001
+From: Fabio Estevam <fabio.estevam@freescale.com>
+Date: Sat, 28 Sep 2013 18:46:18 -0300
+Subject: [PATCH] ARM: mach-mx6: board-mx6q_sabresd: Register SDHC3 first
+Organization: O.S. Systems Software LTDA.
+
+On sabresd boards we boot from SDHC3, so let's register it as mmc0.
+
+Currently eMMC is mmc0 and mmc1 can be SDHC3 or SDHC2 (if present).
+
+Registering SDHC3 is safer as we can always find the rootfs.
+
+Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
+---
+ arch/arm/mach-mx6/board-mx6q_sabresd.c | 5 +----
+ 1 file changed, 1 insertion(+), 4 deletions(-)
+
+diff --git a/arch/arm/mach-mx6/board-mx6q_sabresd.c b/arch/arm/mach-mx6/board-mx6q_sabresd.c
+index 3f9a845..4e6b323 100644
+--- a/arch/arm/mach-mx6/board-mx6q_sabresd.c
++++ b/arch/arm/mach-mx6/board-mx6q_sabresd.c
+@@ -1847,12 +1847,9 @@ static void __init mx6_sabresd_board_init(void)
+
+ imx6q_add_pm_imx(0, &mx6q_sabresd_pm_data);
+
+- /* Move sd4 to first because sd4 connect to emmc.
+- Mfgtools want emmc is mmcblk0 and other sd card is mmcblk1.
+- */
++ imx6q_add_sdhci_usdhc_imx(2, &mx6q_sabresd_sd3_data);
+ imx6q_add_sdhci_usdhc_imx(3, &mx6q_sabresd_sd4_data);
+ imx6q_add_sdhci_usdhc_imx(1, &mx6q_sabresd_sd2_data);
+- imx6q_add_sdhci_usdhc_imx(2, &mx6q_sabresd_sd3_data);
+ imx_add_viv_gpu(&imx6_gpu_data, &imx6q_gpu_pdata);
+ imx6q_sabresd_init_usb();
+ /* SATA is not supported by MX6DL/Solo */
+--
+1.8.4.rc3
+
diff --git a/recipes-kernel/linux/linux-cubox-i-3.0.35/defconfig b/recipes-kernel/linux/linux-cubox-i-3.0.35/defconfig
new file mode 100644
index 0000000..bd0cef0
--- /dev/null
+++ b/recipes-kernel/linux/linux-cubox-i-3.0.35/defconfig
@@ -0,0 +1,366 @@
+CONFIG_EXPERIMENTAL=y
+CONFIG_LOCALVERSION="-4.1.0+yocto"
+CONFIG_SYSVIPC=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_CGROUP_PERF=y
+CONFIG_CGROUP_SCHED=y
+CONFIG_EMBEDDED=y
+CONFIG_PERF_EVENTS=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_ARCH_MXC=y
+CONFIG_GPIO_PCA953X=y
+CONFIG_ARCH_MX6=y
+CONFIG_FORCE_MAX_ZONEORDER=14
+CONFIG_MACH_MX6Q_ARM2=y
+CONFIG_MACH_MX6Q_SABRELITE=y
+CONFIG_MACH_MX6Q_SABRESD=y
+CONFIG_MACH_MX6Q_SABREAUTO=y
+CONFIG_MACH_MX6Q_HDMIDONGLE=y
+CONFIG_MACH_C1=y
+CONFIG_MACH_CUBOX_I=y
+CONFIG_USB_EHCI_ARC_H1=y
+CONFIG_USB_FSL_ARC_OTG=y
+CONFIG_MXC_PWM=y
+CONFIG_MXC_REBOOT_MFGMODE=y
+CONFIG_CLK_DEBUG=y
+CONFIG_DMA_ZONE_SIZE=184
+# CONFIG_SWP_EMULATE is not set
+CONFIG_ARM_ERRATA_743622=y
+CONFIG_ARM_ERRATA_751472=y
+CONFIG_ARM_ERRATA_754322=y
+CONFIG_ARM_ERRATA_775420=y
+CONFIG_ARM_ERRATA_764369=y
+CONFIG_PL310_ERRATA_769419=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_SMP=y
+CONFIG_VMSPLIT_2G=y
+CONFIG_PREEMPT=y
+CONFIG_AEABI=y
+# CONFIG_OABI_COMPAT is not set
+CONFIG_HIGHMEM=y
+CONFIG_COMPACTION=y
+CONFIG_KSM=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="noinitrd console=ttymxc0,115200 root=/dev/mtdblock2 rw rootfstype=jffs2 ip=off"
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_DEFAULT_GOV_INTERACTIVE=y
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_POWERSAVE=y
+CONFIG_CPU_FREQ_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
+CONFIG_CPU_FREQ_IMX=y
+CONFIG_VFP=y
+CONFIG_NEON=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_SUSPEND_DEVICE_TIME_DEBUG=y
+CONFIG_PM_RUNTIME=y
+CONFIG_PM_DEBUG=y
+CONFIG_APM_EMULATION=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_INET_LRO is not set
+# CONFIG_IPV6 is not set
+CONFIG_LLC2=y
+CONFIG_CAN=y
+CONFIG_CAN_RAW=y
+CONFIG_CAN_BCM=y
+CONFIG_CAN_VCAN=y
+CONFIG_CAN_FLEXCAN=y
+CONFIG_BT=y
+CONFIG_BT_L2CAP=y
+CONFIG_BT_SCO=y
+CONFIG_BT_RFCOMM=y
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=y
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_HIDP=y
+CONFIG_BT_HCIBTUSB=y
+CONFIG_BT_HCIUART=y
+CONFIG_BT_HCIUART_ATH3K=y
+CONFIG_BT_HCIVHCI=y
+CONFIG_CFG80211=y
+CONFIG_RFKILL=y
+CONFIG_RFKILL_INPUT=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_CONNECTOR=y
+CONFIG_MTD=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_M25P80=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_GPMI_NAND=y
+CONFIG_MTD_UBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_MISC_DEVICES=y
+CONFIG_MXS_PERFMON=m
+CONFIG_BLK_DEV_SD=y
+CONFIG_SCSI_MULTI_LUN=y
+CONFIG_ATA=y
+# CONFIG_SATA_PMP is not set
+CONFIG_SATA_AHCI_PLATFORM=y
+CONFIG_NETDEVICES=y
+CONFIG_MICREL_PHY=y
+CONFIG_NET_ETHERNET=y
+CONFIG_SMSC911X=y
+CONFIG_FEC_NAPI=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+CONFIG_ATH_COMMON=m
+CONFIG_ATH6KL=m
+CONFIG_BRCMFMAC=y
+CONFIG_HOSTAP=y
+CONFIG_INPUT_POLLDEV=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_EGALAX=y
+CONFIG_TOUCHSCREEN_ELAN=y
+CONFIG_TOUCHSCREEN_MAX11801=y
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_UINPUT=y
+CONFIG_INPUT_ISL29023=y
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_SERIAL_IMX=y
+CONFIG_SERIAL_IMX_CONSOLE=y
+CONFIG_FSL_OTP=y
+CONFIG_HW_RANDOM=y
+CONFIG_MXS_VIIM=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_IMX=y
+CONFIG_SPI=y
+CONFIG_SPI_IMX=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_SABRESD_MAX8903=y
+CONFIG_SENSORS_MAX17135=y
+CONFIG_SENSORS_MAG3110=y
+# CONFIG_MXC_MMA8450 is not set
+CONFIG_WATCHDOG=y
+CONFIG_WATCHDOG_NOWAYOUT=y
+CONFIG_IMX2_WDT=y
+CONFIG_MFD_WM8994=y
+CONFIG_MFD_PFUZE=y
+CONFIG_MFD_MAX17135=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_PFUZE100=y
+CONFIG_REGULATOR_MAX17135=y
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_VIDEO_DEV=y
+CONFIG_IR_GPIO_CIR=y
+# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
+CONFIG_VIDEO_MXC_CAMERA=m
+CONFIG_MXC_CAMERA_OV3640=m
+CONFIG_MXC_CAMERA_OV5640=m
+CONFIG_MXC_CAMERA_OV8820_MIPI=m
+CONFIG_MXC_CAMERA_OV5642=m
+CONFIG_MXC_TVIN_ADV7180=m
+CONFIG_MXC_CAMERA_OV5640_MIPI=m
+CONFIG_MXC_IPU_DEVICE_QUEUE_SDC=m
+CONFIG_USB_VIDEO_CLASS=m
+# CONFIG_RADIO_ADAPTERS is not set
+CONFIG_DRM=y
+CONFIG_DRM_VIVANTE=y
+CONFIG_FB=y
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_BACKLIGHT_PWM=y
+CONFIG_FB_MXC_LDB=y
+CONFIG_FB_MXC_MIPI_DSI=y
+CONFIG_FB_MXC_TRULY_WVGA_SYNC_PANEL=y
+CONFIG_FB_MXC_EINK_PANEL=y
+CONFIG_FB_MXC_HDMI=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_USB_AUDIO=y
+CONFIG_SND_SOC=y
+CONFIG_SND_IMX_SOC=y
+CONFIG_SND_SOC_IMX_SGTL5000=y
+CONFIG_SND_SOC_IMX_WM8962=y
+CONFIG_SND_SOC_IMX_CS42888=y
+CONFIG_SND_SOC_IMX_SPDIF=y
+CONFIG_SND_SOC_IMX_HDMI=y
+CONFIG_HIDRAW=y
+CONFIG_HID_A4TECH=m
+CONFIG_HID_APPLE=m
+CONFIG_HID_BELKIN=m
+CONFIG_HID_CHERRY=m
+CONFIG_HID_CHICONY=m
+CONFIG_HID_CYPRESS=m
+CONFIG_HID_EZKEY=m
+CONFIG_HID_GYRATION=m
+CONFIG_HID_LOGITECH=m
+CONFIG_HID_MICROSOFT=m
+CONFIG_HID_MONTEREY=m
+CONFIG_HID_PANTHERLORD=m
+CONFIG_HID_PETALYNX=m
+CONFIG_HID_SAMSUNG=m
+CONFIG_HID_SONY=m
+CONFIG_HID_SUNPLUS=m
+CONFIG_USB=y
+# CONFIG_USB_DEVICE_CLASS is not set
+CONFIG_USB_SUSPEND=y
+# CONFIG_USB_OTG_WHITELIST is not set
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ARC=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_SERIAL=y
+CONFIG_USB_SERIAL_CONSOLE=y
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_AIRCABLE=m
+CONFIG_USB_SERIAL_ARK3116=m
+CONFIG_USB_SERIAL_BELKIN=m
+CONFIG_USB_SERIAL_CH341=m
+CONFIG_USB_SERIAL_WHITEHEAT=m
+CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
+CONFIG_USB_SERIAL_CP210X=m
+CONFIG_USB_SERIAL_CYPRESS_M8=m
+CONFIG_USB_SERIAL_EMPEG=m
+CONFIG_USB_SERIAL_FTDI_SIO=y
+CONFIG_USB_SERIAL_FUNSOFT=m
+CONFIG_USB_SERIAL_VISOR=m
+CONFIG_USB_SERIAL_IPAQ=m
+CONFIG_USB_SERIAL_IR=m
+CONFIG_USB_SERIAL_EDGEPORT=m
+CONFIG_USB_SERIAL_EDGEPORT_TI=m
+CONFIG_USB_SERIAL_GARMIN=m
+CONFIG_USB_SERIAL_IPW=m
+CONFIG_USB_SERIAL_IUU=m
+CONFIG_USB_SERIAL_KEYSPAN_PDA=m
+CONFIG_USB_SERIAL_KLSI=m
+CONFIG_USB_SERIAL_KOBIL_SCT=m
+CONFIG_USB_SERIAL_MCT_U232=m
+CONFIG_USB_SERIAL_MOS7720=m
+CONFIG_USB_SERIAL_MOS7840=m
+CONFIG_USB_SERIAL_MOTOROLA=m
+CONFIG_USB_SERIAL_NAVMAN=m
+CONFIG_USB_SERIAL_PL2303=y
+CONFIG_USB_SERIAL_OTI6858=m
+CONFIG_USB_SERIAL_QCAUX=m
+CONFIG_USB_SERIAL_QUALCOMM=m
+CONFIG_USB_SERIAL_SPCP8X5=m
+CONFIG_USB_SERIAL_HP4X=m
+CONFIG_USB_SERIAL_SAFE=m
+CONFIG_USB_SERIAL_SAFE_PADDED=y
+CONFIG_USB_SERIAL_SIEMENS_MPI=m
+CONFIG_USB_SERIAL_SIERRAWIRELESS=m
+CONFIG_USB_SERIAL_SYMBOL=m
+CONFIG_USB_SERIAL_TI=m
+CONFIG_USB_SERIAL_CYBERJACK=m
+CONFIG_USB_SERIAL_XIRCOM=m
+CONFIG_USB_SERIAL_OPTION=m
+CONFIG_USB_SERIAL_OMNINET=m
+CONFIG_USB_SERIAL_OPTICON=m
+CONFIG_USB_SERIAL_VIVOPAY_SERIAL=m
+CONFIG_USB_SERIAL_ZIO=m
+CONFIG_USB_SERIAL_SSU100=m
+CONFIG_USB_GADGET=y
+CONFIG_USB_AUDIO=m
+CONFIG_USB_ETH=m
+CONFIG_USB_FILE_STORAGE=m
+CONFIG_USB_G_SERIAL=m
+CONFIG_MXC_OTG=y
+CONFIG_MMC=y
+CONFIG_MMC_UNSAFE_RESUME=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_ESDHC_IMX=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_INTF_DEV_UIE_EMUL=y
+CONFIG_RTC_DRV_PCF8523=y
+CONFIG_RTC_DRV_SNVS=y
+CONFIG_DMADEVICES=y
+CONFIG_MXC_PXP_V2=y
+CONFIG_IMX_SDMA=y
+CONFIG_MXC_IPU=y
+# CONFIG_MXC_HMP4E is not set
+# CONFIG_MXC_HWEVENT is not set
+CONFIG_MXC_ASRC=y
+CONFIG_MXC_MLB150=m
+CONFIG_MXC_GPU_VIV=y
+CONFIG_MXC_MIPI_CSI2=y
+CONFIG_MXC_HDMI_CEC=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
+CONFIG_EXT4_FS=y
+CONFIG_AUTOFS4_FS=m
+CONFIG_FUSE_FS=y
+CONFIG_CUSE=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_JFFS2_FS=y
+CONFIG_UBIFS_FS=y
+CONFIG_CRAMFS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_ROOT_NFS=y
+CONFIG_CIFS=y
+CONFIG_CIFS_STATS=y
+CONFIG_CIFS_STATS2=y
+CONFIG_CIFS_XATTR=y
+CONFIG_CIFS_POSIX=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_EFI_PARTITION=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=m
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+# CONFIG_CRYPTO_MANAGER_DISABLE_TESTS is not set
+CONFIG_CRYPTO_TEST=m
+CONFIG_CRYPTO_CCM=y
+CONFIG_CRYPTO_GCM=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_CTS=y
+CONFIG_CRYPTO_LRW=y
+CONFIG_CRYPTO_PCBC=y
+CONFIG_CRYPTO_XTS=y
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_DEV_FSL_CAAM=y
+CONFIG_CRYPTO_DEV_FSL_CAAM_SM=y
+CONFIG_CRYPTO_DEV_FSL_CAAM_SM_TEST=y
+CONFIG_CRYPTO_DEV_FSL_CAAM_SECVIO=y
+CONFIG_CRC_CCITT=m
diff --git a/recipes-kernel/linux/linux-cubox-i-3.0.35/epdc-Rename-mxcfb_epdc_kernel.h-to-mxc_epdc.h.patch b/recipes-kernel/linux/linux-cubox-i-3.0.35/epdc-Rename-mxcfb_epdc_kernel.h-to-mxc_epdc.h.patch
new file mode 100644
index 0000000..0a20b3f
--- /dev/null
+++ b/recipes-kernel/linux/linux-cubox-i-3.0.35/epdc-Rename-mxcfb_epdc_kernel.h-to-mxc_epdc.h.patch
@@ -0,0 +1,143 @@
+From 149545df26169d257b144ff78934ce9cb5b6818b Mon Sep 17 00:00:00 2001
+From: Otavio Salvador <otavio@ossystems.com.br>
+Date: Sat, 19 Oct 2013 10:55:11 -0300
+Subject: [PATCH] epdc: Rename mxcfb_epdc_kernel.h to mxc_epdc.h
+Organization: O.S. Systems Software LTDA.
+
+This allow for forward compatibility with imx-test >= 3.10.9-1.0.0.
+
+Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
+---
+ drivers/video/mxc/mxc_epdc_fb.c | 2 +-
+ include/linux/mxcfb_epdc.h | 49 +++++++++++++++++++++++++++++++++++++++
+ include/linux/mxcfb_epdc_kernel.h | 49 ---------------------------------------
+ 3 files changed, 50 insertions(+), 50 deletions(-)
+ create mode 100644 include/linux/mxcfb_epdc.h
+ delete mode 100644 include/linux/mxcfb_epdc_kernel.h
+
+diff --git a/drivers/video/mxc/mxc_epdc_fb.c b/drivers/video/mxc/mxc_epdc_fb.c
+index 4103498..b3ef8ea 100644
+--- a/drivers/video/mxc/mxc_epdc_fb.c
++++ b/drivers/video/mxc/mxc_epdc_fb.c
+@@ -43,7 +43,7 @@
+ #include <linux/dmaengine.h>
+ #include <linux/pxp_dma.h>
+ #include <linux/mxcfb.h>
+-#include <linux/mxcfb_epdc_kernel.h>
++#include <linux/mxcfb_epdc.h>
+ #include <linux/gpio.h>
+ #include <linux/regulator/driver.h>
+ #include <linux/fsl_devices.h>
+diff --git a/include/linux/mxcfb_epdc.h b/include/linux/mxcfb_epdc.h
+new file mode 100644
+index 0000000..06fea6f
+--- /dev/null
++++ b/include/linux/mxcfb_epdc.h
+@@ -0,0 +1,49 @@
++/*
++ * Copyright (C) 2010-2012 Freescale Semiconductor, Inc. All Rights Reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
++ *
++ */
++#ifndef _MXCFB_EPDC_KERNEL
++#define _MXCFB_EPDC_KERNEL
++
++void mxc_epdc_fb_set_waveform_modes(struct mxcfb_waveform_modes *modes,
++ struct fb_info *info);
++int mxc_epdc_fb_set_temperature(int temperature, struct fb_info *info);
++int mxc_epdc_fb_set_auto_update(u32 auto_mode, struct fb_info *info);
++int mxc_epdc_fb_send_update(struct mxcfb_update_data *upd_data,
++ struct fb_info *info);
++int mxc_epdc_fb_wait_update_complete(
++ struct mxcfb_update_marker_data *marker_data,
++ struct fb_info *info);
++int mxc_epdc_fb_set_pwrdown_delay(u32 pwrdown_delay,
++ struct fb_info *info);
++int mxc_epdc_get_pwrdown_delay(struct fb_info *info);
++int mxc_epdc_fb_set_upd_scheme(u32 upd_scheme, struct fb_info *info);
++
++void mxc_spdc_fb_set_waveform_modes(struct mxcfb_waveform_modes *modes,
++ struct fb_info *info);
++int mxc_spdc_fb_set_temperature(int temperature, struct fb_info *info);
++int mxc_spdc_fb_set_auto_update(u32 auto_mode, struct fb_info *info);
++int mxc_spdc_fb_send_update(struct mxcfb_update_data *upd_data,
++ struct fb_info *info);
++int mxc_spdc_fb_wait_update_complete(
++ struct mxcfb_update_marker_data *marker_data,
++ struct fb_info *info);
++int mxc_spdc_fb_set_pwrdown_delay(u32 pwrdown_delay,
++ struct fb_info *info);
++int mxc_spdc_get_pwrdown_delay(struct fb_info *info);
++int mxc_spdc_fb_set_upd_scheme(u32 upd_scheme, struct fb_info *info);
++#endif
+diff --git a/include/linux/mxcfb_epdc_kernel.h b/include/linux/mxcfb_epdc_kernel.h
+deleted file mode 100644
+index 06fea6f..0000000
+--- a/include/linux/mxcfb_epdc_kernel.h
++++ /dev/null
+@@ -1,49 +0,0 @@
+-/*
+- * Copyright (C) 2010-2012 Freescale Semiconductor, Inc. All Rights Reserved.
+- *
+- * This program is free software; you can redistribute it and/or modify
+- * it under the terms of the GNU General Public License as published by
+- * the Free Software Foundation; either version 2 of the License, or
+- * (at your option) any later version.
+- *
+- * This program is distributed in the hope that it will be useful,
+- * but WITHOUT ANY WARRANTY; without even the implied warranty of
+- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+- * GNU General Public License for more details.
+- *
+- * You should have received a copy of the GNU General Public License
+- * along with this program; if not, write to the Free Software
+- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+- *
+- */
+-#ifndef _MXCFB_EPDC_KERNEL
+-#define _MXCFB_EPDC_KERNEL
+-
+-void mxc_epdc_fb_set_waveform_modes(struct mxcfb_waveform_modes *modes,
+- struct fb_info *info);
+-int mxc_epdc_fb_set_temperature(int temperature, struct fb_info *info);
+-int mxc_epdc_fb_set_auto_update(u32 auto_mode, struct fb_info *info);
+-int mxc_epdc_fb_send_update(struct mxcfb_update_data *upd_data,
+- struct fb_info *info);
+-int mxc_epdc_fb_wait_update_complete(
+- struct mxcfb_update_marker_data *marker_data,
+- struct fb_info *info);
+-int mxc_epdc_fb_set_pwrdown_delay(u32 pwrdown_delay,
+- struct fb_info *info);
+-int mxc_epdc_get_pwrdown_delay(struct fb_info *info);
+-int mxc_epdc_fb_set_upd_scheme(u32 upd_scheme, struct fb_info *info);
+-
+-void mxc_spdc_fb_set_waveform_modes(struct mxcfb_waveform_modes *modes,
+- struct fb_info *info);
+-int mxc_spdc_fb_set_temperature(int temperature, struct fb_info *info);
+-int mxc_spdc_fb_set_auto_update(u32 auto_mode, struct fb_info *info);
+-int mxc_spdc_fb_send_update(struct mxcfb_update_data *upd_data,
+- struct fb_info *info);
+-int mxc_spdc_fb_wait_update_complete(
+- struct mxcfb_update_marker_data *marker_data,
+- struct fb_info *info);
+-int mxc_spdc_fb_set_pwrdown_delay(u32 pwrdown_delay,
+- struct fb_info *info);
+-int mxc_spdc_get_pwrdown_delay(struct fb_info *info);
+-int mxc_spdc_fb_set_upd_scheme(u32 upd_scheme, struct fb_info *info);
+-#endif
+--
+1.8.4.rc3
+
diff --git a/recipes-kernel/linux/linux-cubox-i-3.0.35/fix-install-breakage-for-fw-images.patch b/recipes-kernel/linux/linux-cubox-i-3.0.35/fix-install-breakage-for-fw-images.patch
new file mode 100644
index 0000000..86d4c37
--- /dev/null
+++ b/recipes-kernel/linux/linux-cubox-i-3.0.35/fix-install-breakage-for-fw-images.patch
@@ -0,0 +1,32 @@
+From f6a15304bc2730ba091eb747c413d4ef4124565e Mon Sep 17 00:00:00 2001
+From: Denys Dmytriyenko <denys at ti.com>
+Date: Mon, 5 Mar 2012 16:34:53 -0500
+Subject: [PATCH] Makefile.fwinst: fix install breakage for FW images residing
+ in firmware/ dir
+
+This fixes below error found on some distros (Gentoo and Fedora):
+*** No rule to make target `lib/firmware/./', needed by `lib/firmware/ti_3410.fw'. Stop.
+
+Upstream-Status: Pending
+
+Signed-off-by: Denys Dmytriyenko <denys at ti.com>
+---
+ scripts/Makefile.fwinst | 2 +-
+ 1 files changed, 1 insertions(+), 1 deletions(-)
+
+diff --git a/scripts/Makefile.fwinst b/scripts/Makefile.fwinst
+index 6bf8e87..4d908d1 100644
+--- a/scripts/Makefile.fwinst
++++ b/scripts/Makefile.fwinst
+@@ -27,7 +27,7 @@ endif
+ installed-mod-fw := $(addprefix $(INSTALL_FW_PATH)/,$(mod-fw))
+
+ installed-fw := $(addprefix $(INSTALL_FW_PATH)/,$(fw-shipped-all))
+-installed-fw-dirs := $(sort $(dir $(installed-fw))) $(INSTALL_FW_PATH)/.
++installed-fw-dirs := $(sort $(dir $(installed-fw))) $(INSTALL_FW_PATH)/./
+
+ # Workaround for make < 3.81, where .SECONDEXPANSION doesn't work.
+ PHONY += $(INSTALL_FW_PATH)/$$(%) install-all-dirs
+--
+1.7.8.5
+
diff --git a/recipes-kernel/linux/linux-cubox-i-3.0.35/mxc_hdmi-dont-require-cea-mode.patch b/recipes-kernel/linux/linux-cubox-i-3.0.35/mxc_hdmi-dont-require-cea-mode.patch
new file mode 100644
index 0000000..99d7f0c
--- /dev/null
+++ b/recipes-kernel/linux/linux-cubox-i-3.0.35/mxc_hdmi-dont-require-cea-mode.patch
@@ -0,0 +1,25 @@
+This fixes problems with DVI monitors connected to the HDMI port
+via a DVI <-> HDMI cable. With dvi monitors, the list of CEA modes
+is always zero, preventing modes higher than 1024x768 to be used.
+This patch disables the CEA mode check.
+
+Upstream-Status: Pending
+
+diff --git a/drivers/video/mxc_hdmi.c b/drivers/video/mxc_hdmi.c
+index 544f352..fa67128 100644
+--- a/drivers/video/mxc_hdmi.c
++++ b/drivers/video/mxc_hdmi.c
+@@ -1804,10 +1804,10 @@ static void mxc_hdmi_edid_rebuild_modelist(struct mxc_hdmi *hdmi)
+ */
+ mode = &hdmi->fbi->monspecs.modedb[i];
+
+- if (!(mode->vmode & FB_VMODE_INTERLACED) &&
+- (mxc_edid_mode_to_vic(mode) != 0)) {
++ if (!(mode->vmode & FB_VMODE_INTERLACED)) {
++ int vic = mxc_edid_mode_to_vic(mode);
+
+- dev_dbg(&hdmi->pdev->dev, "Added mode %d:", i);
++ dev_dbg(&hdmi->pdev->dev, "%s: Added mode %d(VIC %u):", __func__, i, vic);
+ dev_dbg(&hdmi->pdev->dev,
+ "xres = %d, yres = %d, freq = %d, vmode = %d, flag = %d\n",
+ hdmi->fbi->monspecs.modedb[i].xres,
diff --git a/recipes-kernel/linux/linux-cubox-i_3.0.35.bb b/recipes-kernel/linux/linux-cubox-i_3.0.35.bb
new file mode 100644
index 0000000..49b1fe2
--- /dev/null
+++ b/recipes-kernel/linux/linux-cubox-i_3.0.35.bb
@@ -0,0 +1,23 @@
+include recipes-kernel/linux/linux-imx.inc
+
+SRCREV = "be699c6777f376b5f28e60d8d65942ac94b39908"
+LOCALVERSION = "-4.1.0-cubox-i+yocto"
+SRCBRANCH ?= "imx_3.0.35_4.1.0"
+
+# The added patches are the ones from linux-imx 3.0.35 , with exception of these which
+# are already included in the kernel repository:
+# drm-vivante-Add-00-sufix-in-returned-bus-Id.patch
+# 0001-perf-tools-Fix-getrusage-related-build-failure-on-gl.patch
+SRC_URI = "git://github.com/SolidRun/linux-imx6.git;branch=${SRCBRANCH} \
+ file://defconfig \
+ file://epdc-Rename-mxcfb_epdc_kernel.h-to-mxc_epdc.h.patch \
+ file://0002-ARM-7668-1-fix-memset-related-crashes-caused-by-rece.patch \
+ file://0003-ARM-7670-1-fix-the-memset-fix.patch \
+ file://0004-ENGR00271136-Fix-build-break-when-CONFIG_CLK_DEBUG-i.patch \
+ file://0005-ENGR00271359-Add-Multi-touch-support.patch \
+ file://0006-Add-support-for-DVI-monitors.patch \
+ file://0007-ARM-mach-mx6-board-mx6q_sabresd-Register-SDHC3-first.patch \
+ file://mxc_hdmi-dont-require-cea-mode.patch \
+ file://fix-install-breakage-for-fw-images.patch"
+
+COMPATIBLE_MACHINE = "(cubox-i)"
--
1.8.5.2
^ permalink raw reply related [flat|nested] 5+ messages in thread