* Terratec H7 with yet another usb ID
@ 2014-02-03 20:21 Rik van Mierlo
2014-02-03 22:33 ` Antti Palosaari
0 siblings, 1 reply; 6+ messages in thread
From: Rik van Mierlo @ 2014-02-03 20:21 UTC (permalink / raw)
To: linux-media
Hi,
I've recently purchased a Terratec H7, based on the fact that is was
supported for a while now. Unfortunately, it turns out that my device
uses a different product id, and maybe is not quite the same device
inside either.
ProductID for the Terratec H7 revisions in the module is either 10b4 or
10a3, the one I purchased is 10a5. Following this patch:
https://patchwork.linuxtv.org/patch/9691
I modified drivers/media/usb/dvb-usb-v2/az6007.c to include an
additional device:
static struct usb_device_id az6007_usb_table[] = {
{DVB_USB_DEVICE(USB_VID_AZUREWAVE, USB_PID_AZUREWAVE_6007,
&az6007_props, "Azurewave 6007", RC_MAP_EMPTY)},
{DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7,
&az6007_props, "Terratec H7",
RC_MAP_NEC_TERRATEC_CINERGY_XS)},
{DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7_2,
&az6007_props, "Terratec H7",
RC_MAP_NEC_TERRATEC_CINERGY_XS)},
{DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7_3,
&az6007_props, "Terratec H7",
RC_MAP_NEC_TERRATEC_CINERGY_XS)},
{DVB_USB_DEVICE(USB_VID_TECHNISAT,
USB_PID_TECHNISAT_USB2_CABLESTAR_HDCI,
&az6007_cablestar_hdci_props, "Technisat CableStar
Combo HD CI", RC_MAP_EMPTY)},
{0},
};
and added the following to drivers/media/dvb-core/dvb-usb-ids.h
#define USB_PID_TERRATEC_H7_3 0x10a5
and recompiled/installed the kernel and modules. The module seems to
have changed somewhat in 3.12.6 from the version that the patch was
meant for, so I hope I this was all I had to change.
Rebooting and plugging in the device now at least leads to a recognized
device, but scanning for channels with w_scan does not work, and from
the dmesg output below, it seems something is not working after loading
the drxk firmware. Does anybody know what I could try next to get this
device working? Could it be that the drxk firmware is not suitable for
this revision of the device?
[ 700.112072] usb 4-2: new high-speed USB device number 2 using
ehci-pci
[ 700.245092] usb 4-2: New USB device found, idVendor=0ccd,
idProduct=10a5
[ 700.245105] usb 4-2: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 700.245114] usb 4-2: Product: TERRATEC T2/T/C CI USB
[ 700.245123] usb 4-2: Manufacturer: TERRATEC
[ 700.245131] usb 4-2: SerialNumber: 20130903
[ 700.494693] usb read operation failed. (-32)
[ 700.495039] usb write operation failed. (-32)
[ 700.495413] usb write operation failed. (-32)
[ 700.495787] usb write operation failed. (-32)
[ 700.495800] usb 4-2: dvb_usb_v2: found a 'Terratec H7' in cold state
[ 700.507381] usb 4-2: firmware: direct-loading firmware
dvb-usb-terratec-h7-az6007.fw
[ 700.507397] usb 4-2: dvb_usb_v2: downloading firmware from file
'dvb-usb-terratec-h7-az6007.fw'
[ 700.524301] usb 4-2: dvb_usb_v2: found a 'Terratec H7' in warm state
[ 701.760878] usb 4-2: dvb_usb_v2: will pass the complete MPEG2
transport stream to the software demuxer
[ 701.760947] DVB: registering new adapter (Terratec H7)
[ 701.763853] usb 4-2: dvb_usb_v2: MAC address: c2:cd:0c:a5:10:00
[ 701.846469] drxk: frontend initialized.
[ 701.849123] usb 4-2: firmware: direct-loading firmware
dvb-usb-terratec-h7-drxk.fw
[ 701.849215] usb 4-2: DVB: registering adapter 0 frontend 0 (DRXK)...
[ 701.881072] drxk: status = 0x00c04125
[ 701.881082] drxk: DeviceID 0x04 not supported
[ 701.881090] drxk: Error -22 on init_drxk
[ 701.908184] mt2063_attach: Attaching MT2063
[ 701.940248] Registered IR keymap rc-nec-terratec-cinergy-xs
[ 701.940547] input: Terratec H7 as
/devices/pci0000:00/0000:00:1d.7/usb4/4-2/rc/rc0/input16
[ 701.942559] rc0: Terratec H7 as
/devices/pci0000:00/0000:00:1d.7/usb4/4-2/rc/rc0
[ 701.942575] usb 4-2: dvb_usb_v2: schedule remote query interval to
400 msecs
[ 701.942587] usb 4-2: dvb_usb_v2: 'Terratec H7' successfully
initialized and connected
[ 701.942643] usbcore: registered new interface driver dvb_usb_az6007
Regards,
Rik van Mierlo
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Terratec H7 with yet another usb ID
2014-02-03 20:21 Terratec H7 with yet another usb ID Rik van Mierlo
@ 2014-02-03 22:33 ` Antti Palosaari
2014-12-05 14:51 ` Eddi De Pieri
0 siblings, 1 reply; 6+ messages in thread
From: Antti Palosaari @ 2014-02-03 22:33 UTC (permalink / raw)
To: Rik van Mierlo, linux-media
Hei Rik
On 03.02.2014 22:21, Rik van Mierlo wrote:
> Hi,
>
> I've recently purchased a Terratec H7, based on the fact that is was
> supported for a while now. Unfortunately, it turns out that my device
> uses a different product id, and maybe is not quite the same device
> inside either.
>
> ProductID for the Terratec H7 revisions in the module is either 10b4 or
> 10a3, the one I purchased is 10a5. Following this patch:
>
> https://patchwork.linuxtv.org/patch/9691
>
> I modified drivers/media/usb/dvb-usb-v2/az6007.c to include an
> additional device:
>
> static struct usb_device_id az6007_usb_table[] = {
> {DVB_USB_DEVICE(USB_VID_AZUREWAVE, USB_PID_AZUREWAVE_6007,
> &az6007_props, "Azurewave 6007", RC_MAP_EMPTY)},
> {DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7,
> &az6007_props, "Terratec H7",
> RC_MAP_NEC_TERRATEC_CINERGY_XS)},
> {DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7_2,
> &az6007_props, "Terratec H7",
> RC_MAP_NEC_TERRATEC_CINERGY_XS)},
> {DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7_3,
> &az6007_props, "Terratec H7",
> RC_MAP_NEC_TERRATEC_CINERGY_XS)},
> {DVB_USB_DEVICE(USB_VID_TECHNISAT,
> USB_PID_TECHNISAT_USB2_CABLESTAR_HDCI,
> &az6007_cablestar_hdci_props, "Technisat CableStar
> Combo HD CI", RC_MAP_EMPTY)},
> {0},
> };
>
> and added the following to drivers/media/dvb-core/dvb-usb-ids.h
>
> #define USB_PID_TERRATEC_H7_3 0x10a5
>
> and recompiled/installed the kernel and modules. The module seems to
> have changed somewhat in 3.12.6 from the version that the patch was
> meant for, so I hope I this was all I had to change.
>
> Rebooting and plugging in the device now at least leads to a recognized
> device, but scanning for channels with w_scan does not work, and from
> the dmesg output below, it seems something is not working after loading
> the drxk firmware. Does anybody know what I could try next to get this
> device working? Could it be that the drxk firmware is not suitable for
> this revision of the device?
>
> [ 700.112072] usb 4-2: new high-speed USB device number 2 using ehci-pci
> [ 700.245092] usb 4-2: New USB device found, idVendor=0ccd, idProduct=10a5
> [ 700.245105] usb 4-2: New USB device strings: Mfr=1, Product=2,
> SerialNumber=3
> [ 700.245114] usb 4-2: Product: TERRATEC T2/T/C CI USB
> [ 700.245123] usb 4-2: Manufacturer: TERRATEC
> [ 700.245131] usb 4-2: SerialNumber: 20130903
> [ 700.494693] usb read operation failed. (-32)
> [ 700.495039] usb write operation failed. (-32)
> [ 700.495413] usb write operation failed. (-32)
> [ 700.495787] usb write operation failed. (-32)
These low level errors does not promise any good. Are these coming from
USB stack as there is no even bus ID (4-2)...
> [ 700.495800] usb 4-2: dvb_usb_v2: found a 'Terratec H7' in cold state
> [ 700.507381] usb 4-2: firmware: direct-loading firmware
> dvb-usb-terratec-h7-az6007.fw
> [ 700.507397] usb 4-2: dvb_usb_v2: downloading firmware from file
> 'dvb-usb-terratec-h7-az6007.fw'
> [ 700.524301] usb 4-2: dvb_usb_v2: found a 'Terratec H7' in warm state
> [ 701.760878] usb 4-2: dvb_usb_v2: will pass the complete MPEG2
> transport stream to the software demuxer
> [ 701.760947] DVB: registering new adapter (Terratec H7)
> [ 701.763853] usb 4-2: dvb_usb_v2: MAC address: c2:cd:0c:a5:10:00
> [ 701.846469] drxk: frontend initialized.
> [ 701.849123] usb 4-2: firmware: direct-loading firmware
> dvb-usb-terratec-h7-drxk.fw
> [ 701.849215] usb 4-2: DVB: registering adapter 0 frontend 0 (DRXK)...
> [ 701.881072] drxk: status = 0x00c04125
> [ 701.881082] drxk: DeviceID 0x04 not supported
> [ 701.881090] drxk: Error -22 on init_drxk
I suspect there is no DRX-K.
> [ 701.908184] mt2063_attach: Attaching MT2063
> [ 701.940248] Registered IR keymap rc-nec-terratec-cinergy-xs
> [ 701.940547] input: Terratec H7 as
> /devices/pci0000:00/0000:00:1d.7/usb4/4-2/rc/rc0/input16
> [ 701.942559] rc0: Terratec H7 as
> /devices/pci0000:00/0000:00:1d.7/usb4/4-2/rc/rc0
> [ 701.942575] usb 4-2: dvb_usb_v2: schedule remote query interval to
> 400 msecs
> [ 701.942587] usb 4-2: dvb_usb_v2: 'Terratec H7' successfully
> initialized and connected
> [ 701.942643] usbcore: registered new interface driver dvb_usb_az6007
hmm, a little bit surprising that driver accepts hardware even those
fatal errors.
My guess is that there is no DRX-K but some other demod or likely more
changed chips than demod. DRX-K is rather old demod and there is not
very many newer alternatives on the market. Silicon Labs chipset ? Open
the device in look what chips it has eaten.
regards
Antti
--
http://palosaari.fi/
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Terratec H7 with yet another usb ID
2014-02-03 22:33 ` Antti Palosaari
@ 2014-12-05 14:51 ` Eddi De Pieri
2014-12-05 15:11 ` Antti Palosaari
0 siblings, 1 reply; 6+ messages in thread
From: Eddi De Pieri @ 2014-12-05 14:51 UTC (permalink / raw)
To: Antti Palosaari; +Cc: Rik van Mierlo, linux-media
Hi,
I got a sample usb tuner with similar issue with following
vendor/product 13d3:0ccd.
Onboard it have: CY7C68013A-56PVXC and a SI2168-40. The tuner isn't
visible since is covered by a shield.
I've tried to patch the az6007 to make it working.
si2168 4-0064: Silicon Labs Si2168 successfully attached
si2157 5-0060: unknown chip version Si2147-A30
after applying latest patch from patchwork:
si2157 5-0060: Silicon Labs Si2157/Si2158 successfully attached
Now tuner seems to be connected but a w_scan don't detect any channel...
Can you give me some some hint on troubleshooting this issue?
Actually I'm brutally changed the initialization with copy and paste
of silab attach from cxusb.c and em28xx-dvb.c by removing the drxk
init..
Since the chinese producer recicled old vid/pid.but what is the
correct way to probe for multiple frontend and choose the right one?
Eddi
On Mon, Feb 3, 2014 at 11:33 PM, Antti Palosaari <crope@iki.fi> wrote:
> Hei Rik
>
>
> On 03.02.2014 22:21, Rik van Mierlo wrote:
>>
>> Hi,
>>
>> I've recently purchased a Terratec H7, based on the fact that is was
>> supported for a while now. Unfortunately, it turns out that my device
>> uses a different product id, and maybe is not quite the same device
>> inside either.
>>
>> ProductID for the Terratec H7 revisions in the module is either 10b4 or
>> 10a3, the one I purchased is 10a5. Following this patch:
>>
>> https://patchwork.linuxtv.org/patch/9691
>>
>> I modified drivers/media/usb/dvb-usb-v2/az6007.c to include an
>> additional device:
>>
>> static struct usb_device_id az6007_usb_table[] = {
>> {DVB_USB_DEVICE(USB_VID_AZUREWAVE, USB_PID_AZUREWAVE_6007,
>> &az6007_props, "Azurewave 6007", RC_MAP_EMPTY)},
>> {DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7,
>> &az6007_props, "Terratec H7",
>> RC_MAP_NEC_TERRATEC_CINERGY_XS)},
>> {DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7_2,
>> &az6007_props, "Terratec H7",
>> RC_MAP_NEC_TERRATEC_CINERGY_XS)},
>> {DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7_3,
>> &az6007_props, "Terratec H7",
>> RC_MAP_NEC_TERRATEC_CINERGY_XS)},
>> {DVB_USB_DEVICE(USB_VID_TECHNISAT,
>> USB_PID_TECHNISAT_USB2_CABLESTAR_HDCI,
>> &az6007_cablestar_hdci_props, "Technisat CableStar
>> Combo HD CI", RC_MAP_EMPTY)},
>> {0},
>> };
>>
>> and added the following to drivers/media/dvb-core/dvb-usb-ids.h
>>
>> #define USB_PID_TERRATEC_H7_3 0x10a5
>>
>> and recompiled/installed the kernel and modules. The module seems to
>> have changed somewhat in 3.12.6 from the version that the patch was
>> meant for, so I hope I this was all I had to change.
>>
>> Rebooting and plugging in the device now at least leads to a recognized
>> device, but scanning for channels with w_scan does not work, and from
>> the dmesg output below, it seems something is not working after loading
>> the drxk firmware. Does anybody know what I could try next to get this
>> device working? Could it be that the drxk firmware is not suitable for
>> this revision of the device?
>>
>> [ 700.112072] usb 4-2: new high-speed USB device number 2 using ehci-pci
>> [ 700.245092] usb 4-2: New USB device found, idVendor=0ccd,
>> idProduct=10a5
>> [ 700.245105] usb 4-2: New USB device strings: Mfr=1, Product=2,
>> SerialNumber=3
>> [ 700.245114] usb 4-2: Product: TERRATEC T2/T/C CI USB
>> [ 700.245123] usb 4-2: Manufacturer: TERRATEC
>> [ 700.245131] usb 4-2: SerialNumber: 20130903
>> [ 700.494693] usb read operation failed. (-32)
>> [ 700.495039] usb write operation failed. (-32)
>> [ 700.495413] usb write operation failed. (-32)
>> [ 700.495787] usb write operation failed. (-32)
>
>
> These low level errors does not promise any good. Are these coming from USB
> stack as there is no even bus ID (4-2)...
>
>> [ 700.495800] usb 4-2: dvb_usb_v2: found a 'Terratec H7' in cold state
>> [ 700.507381] usb 4-2: firmware: direct-loading firmware
>> dvb-usb-terratec-h7-az6007.fw
>> [ 700.507397] usb 4-2: dvb_usb_v2: downloading firmware from file
>> 'dvb-usb-terratec-h7-az6007.fw'
>> [ 700.524301] usb 4-2: dvb_usb_v2: found a 'Terratec H7' in warm state
>> [ 701.760878] usb 4-2: dvb_usb_v2: will pass the complete MPEG2
>> transport stream to the software demuxer
>> [ 701.760947] DVB: registering new adapter (Terratec H7)
>> [ 701.763853] usb 4-2: dvb_usb_v2: MAC address: c2:cd:0c:a5:10:00
>> [ 701.846469] drxk: frontend initialized.
>> [ 701.849123] usb 4-2: firmware: direct-loading firmware
>> dvb-usb-terratec-h7-drxk.fw
>> [ 701.849215] usb 4-2: DVB: registering adapter 0 frontend 0 (DRXK)...
>> [ 701.881072] drxk: status = 0x00c04125
>> [ 701.881082] drxk: DeviceID 0x04 not supported
>> [ 701.881090] drxk: Error -22 on init_drxk
>
>
> I suspect there is no DRX-K.
>
>> [ 701.908184] mt2063_attach: Attaching MT2063
>> [ 701.940248] Registered IR keymap rc-nec-terratec-cinergy-xs
>> [ 701.940547] input: Terratec H7 as
>> /devices/pci0000:00/0000:00:1d.7/usb4/4-2/rc/rc0/input16
>> [ 701.942559] rc0: Terratec H7 as
>> /devices/pci0000:00/0000:00:1d.7/usb4/4-2/rc/rc0
>> [ 701.942575] usb 4-2: dvb_usb_v2: schedule remote query interval to
>> 400 msecs
>> [ 701.942587] usb 4-2: dvb_usb_v2: 'Terratec H7' successfully
>> initialized and connected
>> [ 701.942643] usbcore: registered new interface driver dvb_usb_az6007
>
>
> hmm, a little bit surprising that driver accepts hardware even those fatal
> errors.
>
> My guess is that there is no DRX-K but some other demod or likely more
> changed chips than demod. DRX-K is rather old demod and there is not very
> many newer alternatives on the market. Silicon Labs chipset ? Open the
> device in look what chips it has eaten.
>
> regards
> Antti
>
> --
> http://palosaari.fi/
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Terratec H7 with yet another usb ID
2014-12-05 14:51 ` Eddi De Pieri
@ 2014-12-05 15:11 ` Antti Palosaari
2014-12-05 16:27 ` Eddi De Pieri
0 siblings, 1 reply; 6+ messages in thread
From: Antti Palosaari @ 2014-12-05 15:11 UTC (permalink / raw)
To: Eddi De Pieri; +Cc: Rik van Mierlo, linux-media
Moikka
Take USB sniffs and generate driver C-code from that sniff. Then
copy&paste that code to driver until is starts working. After that, you
could remove all the code until you find minimum set of needed changes
(error and trial).
regards
Antti
On 12/05/2014 04:51 PM, Eddi De Pieri wrote:
> Hi,
>
> I got a sample usb tuner with similar issue with following
> vendor/product 13d3:0ccd.
>
> Onboard it have: CY7C68013A-56PVXC and a SI2168-40. The tuner isn't
> visible since is covered by a shield.
>
> I've tried to patch the az6007 to make it working.
>
> si2168 4-0064: Silicon Labs Si2168 successfully attached
> si2157 5-0060: unknown chip version Si2147-A30
>
> after applying latest patch from patchwork:
>
> si2157 5-0060: Silicon Labs Si2157/Si2158 successfully attached
>
> Now tuner seems to be connected but a w_scan don't detect any channel...
>
> Can you give me some some hint on troubleshooting this issue?
>
> Actually I'm brutally changed the initialization with copy and paste
> of silab attach from cxusb.c and em28xx-dvb.c by removing the drxk
> init..
>
> Since the chinese producer recicled old vid/pid.but what is the
> correct way to probe for multiple frontend and choose the right one?
>
> Eddi
>
>
> On Mon, Feb 3, 2014 at 11:33 PM, Antti Palosaari <crope@iki.fi> wrote:
>> Hei Rik
>>
>>
>> On 03.02.2014 22:21, Rik van Mierlo wrote:
>>>
>>> Hi,
>>>
>>> I've recently purchased a Terratec H7, based on the fact that is was
>>> supported for a while now. Unfortunately, it turns out that my device
>>> uses a different product id, and maybe is not quite the same device
>>> inside either.
>>>
>>> ProductID for the Terratec H7 revisions in the module is either 10b4 or
>>> 10a3, the one I purchased is 10a5. Following this patch:
>>>
>>> https://patchwork.linuxtv.org/patch/9691
>>>
>>> I modified drivers/media/usb/dvb-usb-v2/az6007.c to include an
>>> additional device:
>>>
>>> static struct usb_device_id az6007_usb_table[] = {
>>> {DVB_USB_DEVICE(USB_VID_AZUREWAVE, USB_PID_AZUREWAVE_6007,
>>> &az6007_props, "Azurewave 6007", RC_MAP_EMPTY)},
>>> {DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7,
>>> &az6007_props, "Terratec H7",
>>> RC_MAP_NEC_TERRATEC_CINERGY_XS)},
>>> {DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7_2,
>>> &az6007_props, "Terratec H7",
>>> RC_MAP_NEC_TERRATEC_CINERGY_XS)},
>>> {DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7_3,
>>> &az6007_props, "Terratec H7",
>>> RC_MAP_NEC_TERRATEC_CINERGY_XS)},
>>> {DVB_USB_DEVICE(USB_VID_TECHNISAT,
>>> USB_PID_TECHNISAT_USB2_CABLESTAR_HDCI,
>>> &az6007_cablestar_hdci_props, "Technisat CableStar
>>> Combo HD CI", RC_MAP_EMPTY)},
>>> {0},
>>> };
>>>
>>> and added the following to drivers/media/dvb-core/dvb-usb-ids.h
>>>
>>> #define USB_PID_TERRATEC_H7_3 0x10a5
>>>
>>> and recompiled/installed the kernel and modules. The module seems to
>>> have changed somewhat in 3.12.6 from the version that the patch was
>>> meant for, so I hope I this was all I had to change.
>>>
>>> Rebooting and plugging in the device now at least leads to a recognized
>>> device, but scanning for channels with w_scan does not work, and from
>>> the dmesg output below, it seems something is not working after loading
>>> the drxk firmware. Does anybody know what I could try next to get this
>>> device working? Could it be that the drxk firmware is not suitable for
>>> this revision of the device?
>>>
>>> [ 700.112072] usb 4-2: new high-speed USB device number 2 using ehci-pci
>>> [ 700.245092] usb 4-2: New USB device found, idVendor=0ccd,
>>> idProduct=10a5
>>> [ 700.245105] usb 4-2: New USB device strings: Mfr=1, Product=2,
>>> SerialNumber=3
>>> [ 700.245114] usb 4-2: Product: TERRATEC T2/T/C CI USB
>>> [ 700.245123] usb 4-2: Manufacturer: TERRATEC
>>> [ 700.245131] usb 4-2: SerialNumber: 20130903
>>> [ 700.494693] usb read operation failed. (-32)
>>> [ 700.495039] usb write operation failed. (-32)
>>> [ 700.495413] usb write operation failed. (-32)
>>> [ 700.495787] usb write operation failed. (-32)
>>
>>
>> These low level errors does not promise any good. Are these coming from USB
>> stack as there is no even bus ID (4-2)...
>>
>>> [ 700.495800] usb 4-2: dvb_usb_v2: found a 'Terratec H7' in cold state
>>> [ 700.507381] usb 4-2: firmware: direct-loading firmware
>>> dvb-usb-terratec-h7-az6007.fw
>>> [ 700.507397] usb 4-2: dvb_usb_v2: downloading firmware from file
>>> 'dvb-usb-terratec-h7-az6007.fw'
>>> [ 700.524301] usb 4-2: dvb_usb_v2: found a 'Terratec H7' in warm state
>>> [ 701.760878] usb 4-2: dvb_usb_v2: will pass the complete MPEG2
>>> transport stream to the software demuxer
>>> [ 701.760947] DVB: registering new adapter (Terratec H7)
>>> [ 701.763853] usb 4-2: dvb_usb_v2: MAC address: c2:cd:0c:a5:10:00
>>> [ 701.846469] drxk: frontend initialized.
>>> [ 701.849123] usb 4-2: firmware: direct-loading firmware
>>> dvb-usb-terratec-h7-drxk.fw
>>> [ 701.849215] usb 4-2: DVB: registering adapter 0 frontend 0 (DRXK)...
>>> [ 701.881072] drxk: status = 0x00c04125
>>> [ 701.881082] drxk: DeviceID 0x04 not supported
>>> [ 701.881090] drxk: Error -22 on init_drxk
>>
>>
>> I suspect there is no DRX-K.
>>
>>> [ 701.908184] mt2063_attach: Attaching MT2063
>>> [ 701.940248] Registered IR keymap rc-nec-terratec-cinergy-xs
>>> [ 701.940547] input: Terratec H7 as
>>> /devices/pci0000:00/0000:00:1d.7/usb4/4-2/rc/rc0/input16
>>> [ 701.942559] rc0: Terratec H7 as
>>> /devices/pci0000:00/0000:00:1d.7/usb4/4-2/rc/rc0
>>> [ 701.942575] usb 4-2: dvb_usb_v2: schedule remote query interval to
>>> 400 msecs
>>> [ 701.942587] usb 4-2: dvb_usb_v2: 'Terratec H7' successfully
>>> initialized and connected
>>> [ 701.942643] usbcore: registered new interface driver dvb_usb_az6007
>>
>>
>> hmm, a little bit surprising that driver accepts hardware even those fatal
>> errors.
>>
>> My guess is that there is no DRX-K but some other demod or likely more
>> changed chips than demod. DRX-K is rather old demod and there is not very
>> many newer alternatives on the market. Silicon Labs chipset ? Open the
>> device in look what chips it has eaten.
>>
>> regards
>> Antti
>>
>> --
>> http://palosaari.fi/
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-media" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
http://palosaari.fi/
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Terratec H7 with yet another usb ID
2014-12-05 15:11 ` Antti Palosaari
@ 2014-12-05 16:27 ` Eddi De Pieri
2014-12-06 15:40 ` Olli Salonen
0 siblings, 1 reply; 6+ messages in thread
From: Eddi De Pieri @ 2014-12-05 16:27 UTC (permalink / raw)
To: Antti Palosaari; +Cc: Rik van Mierlo, linux-media
Hi Rik,
I've download Terratec H7 rev 4 should be a
TechnoTrend_TT-TVStick_CT2-44xx clone so you could try to patch
dvbsky.c driver.
Strings inside the windows driver:
T E R R A T E C S 7 D i g i t a l T u n e r ( D V B - S / S 2 )
T T - c o n n e c t C T 2 _ 4 6 5 0 D V B - T / T 2 T u n e r
T E R R A T E C H 7 D i g i t a l T u n e r ( D V B - T / T 2 )
T T - c o n n e c t C T 2 _ 4 6 5 0 D V B - C T u n e r
T E R R A T E C H 7 D i g i t a l T u n e r ( D V B - C )
Regards...
Eddi
On Fri, Dec 5, 2014 at 4:11 PM, Antti Palosaari <crope@iki.fi> wrote:
> Moikka
> Take USB sniffs and generate driver C-code from that sniff. Then copy&paste
> that code to driver until is starts working. After that, you could remove
> all the code until you find minimum set of needed changes (error and trial).
>
> regards
> Antti
>
>
> On 12/05/2014 04:51 PM, Eddi De Pieri wrote:
>>
>> Hi,
>>
>> I got a sample usb tuner with similar issue with following
>> vendor/product 13d3:0ccd.
>>
>> Onboard it have: CY7C68013A-56PVXC and a SI2168-40. The tuner isn't
>> visible since is covered by a shield.
>>
>> I've tried to patch the az6007 to make it working.
>>
>> si2168 4-0064: Silicon Labs Si2168 successfully attached
>> si2157 5-0060: unknown chip version Si2147-A30
>>
>> after applying latest patch from patchwork:
>>
>> si2157 5-0060: Silicon Labs Si2157/Si2158 successfully attached
>>
>> Now tuner seems to be connected but a w_scan don't detect any channel...
>>
>> Can you give me some some hint on troubleshooting this issue?
>>
>> Actually I'm brutally changed the initialization with copy and paste
>> of silab attach from cxusb.c and em28xx-dvb.c by removing the drxk
>> init..
>>
>> Since the chinese producer recicled old vid/pid.but what is the
>> correct way to probe for multiple frontend and choose the right one?
>>
>> Eddi
>>
>>
>> On Mon, Feb 3, 2014 at 11:33 PM, Antti Palosaari <crope@iki.fi> wrote:
>>>
>>> Hei Rik
>>>
>>>
>>> On 03.02.2014 22:21, Rik van Mierlo wrote:
>>>>
>>>>
>>>> Hi,
>>>>
>>>> I've recently purchased a Terratec H7, based on the fact that is was
>>>> supported for a while now. Unfortunately, it turns out that my device
>>>> uses a different product id, and maybe is not quite the same device
>>>> inside either.
>>>>
>>>> ProductID for the Terratec H7 revisions in the module is either 10b4 or
>>>> 10a3, the one I purchased is 10a5. Following this patch:
>>>>
>>>> https://patchwork.linuxtv.org/patch/9691
>>>>
>>>> I modified drivers/media/usb/dvb-usb-v2/az6007.c to include an
>>>> additional device:
>>>>
>>>> static struct usb_device_id az6007_usb_table[] = {
>>>> {DVB_USB_DEVICE(USB_VID_AZUREWAVE, USB_PID_AZUREWAVE_6007,
>>>> &az6007_props, "Azurewave 6007", RC_MAP_EMPTY)},
>>>> {DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7,
>>>> &az6007_props, "Terratec H7",
>>>> RC_MAP_NEC_TERRATEC_CINERGY_XS)},
>>>> {DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7_2,
>>>> &az6007_props, "Terratec H7",
>>>> RC_MAP_NEC_TERRATEC_CINERGY_XS)},
>>>> {DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7_3,
>>>> &az6007_props, "Terratec H7",
>>>> RC_MAP_NEC_TERRATEC_CINERGY_XS)},
>>>> {DVB_USB_DEVICE(USB_VID_TECHNISAT,
>>>> USB_PID_TECHNISAT_USB2_CABLESTAR_HDCI,
>>>> &az6007_cablestar_hdci_props, "Technisat CableStar
>>>> Combo HD CI", RC_MAP_EMPTY)},
>>>> {0},
>>>> };
>>>>
>>>> and added the following to drivers/media/dvb-core/dvb-usb-ids.h
>>>>
>>>> #define USB_PID_TERRATEC_H7_3 0x10a5
>>>>
>>>> and recompiled/installed the kernel and modules. The module seems to
>>>> have changed somewhat in 3.12.6 from the version that the patch was
>>>> meant for, so I hope I this was all I had to change.
>>>>
>>>> Rebooting and plugging in the device now at least leads to a recognized
>>>> device, but scanning for channels with w_scan does not work, and from
>>>> the dmesg output below, it seems something is not working after loading
>>>> the drxk firmware. Does anybody know what I could try next to get this
>>>> device working? Could it be that the drxk firmware is not suitable for
>>>> this revision of the device?
>>>>
>>>> [ 700.112072] usb 4-2: new high-speed USB device number 2 using
>>>> ehci-pci
>>>> [ 700.245092] usb 4-2: New USB device found, idVendor=0ccd,
>>>> idProduct=10a5
>>>> [ 700.245105] usb 4-2: New USB device strings: Mfr=1, Product=2,
>>>> SerialNumber=3
>>>> [ 700.245114] usb 4-2: Product: TERRATEC T2/T/C CI USB
>>>> [ 700.245123] usb 4-2: Manufacturer: TERRATEC
>>>> [ 700.245131] usb 4-2: SerialNumber: 20130903
>>>> [ 700.494693] usb read operation failed. (-32)
>>>> [ 700.495039] usb write operation failed. (-32)
>>>> [ 700.495413] usb write operation failed. (-32)
>>>> [ 700.495787] usb write operation failed. (-32)
>>>
>>>
>>>
>>> These low level errors does not promise any good. Are these coming from
>>> USB
>>> stack as there is no even bus ID (4-2)...
>>>
>>>> [ 700.495800] usb 4-2: dvb_usb_v2: found a 'Terratec H7' in cold state
>>>> [ 700.507381] usb 4-2: firmware: direct-loading firmware
>>>> dvb-usb-terratec-h7-az6007.fw
>>>> [ 700.507397] usb 4-2: dvb_usb_v2: downloading firmware from file
>>>> 'dvb-usb-terratec-h7-az6007.fw'
>>>> [ 700.524301] usb 4-2: dvb_usb_v2: found a 'Terratec H7' in warm state
>>>> [ 701.760878] usb 4-2: dvb_usb_v2: will pass the complete MPEG2
>>>> transport stream to the software demuxer
>>>> [ 701.760947] DVB: registering new adapter (Terratec H7)
>>>> [ 701.763853] usb 4-2: dvb_usb_v2: MAC address: c2:cd:0c:a5:10:00
>>>> [ 701.846469] drxk: frontend initialized.
>>>> [ 701.849123] usb 4-2: firmware: direct-loading firmware
>>>> dvb-usb-terratec-h7-drxk.fw
>>>> [ 701.849215] usb 4-2: DVB: registering adapter 0 frontend 0 (DRXK)...
>>>> [ 701.881072] drxk: status = 0x00c04125
>>>> [ 701.881082] drxk: DeviceID 0x04 not supported
>>>> [ 701.881090] drxk: Error -22 on init_drxk
>>>
>>>
>>>
>>> I suspect there is no DRX-K.
>>>
>>>> [ 701.908184] mt2063_attach: Attaching MT2063
>>>> [ 701.940248] Registered IR keymap rc-nec-terratec-cinergy-xs
>>>> [ 701.940547] input: Terratec H7 as
>>>> /devices/pci0000:00/0000:00:1d.7/usb4/4-2/rc/rc0/input16
>>>> [ 701.942559] rc0: Terratec H7 as
>>>> /devices/pci0000:00/0000:00:1d.7/usb4/4-2/rc/rc0
>>>> [ 701.942575] usb 4-2: dvb_usb_v2: schedule remote query interval to
>>>> 400 msecs
>>>> [ 701.942587] usb 4-2: dvb_usb_v2: 'Terratec H7' successfully
>>>> initialized and connected
>>>> [ 701.942643] usbcore: registered new interface driver dvb_usb_az6007
>>>
>>>
>>>
>>> hmm, a little bit surprising that driver accepts hardware even those
>>> fatal
>>> errors.
>>>
>>> My guess is that there is no DRX-K but some other demod or likely more
>>> changed chips than demod. DRX-K is rather old demod and there is not very
>>> many newer alternatives on the market. Silicon Labs chipset ? Open the
>>> device in look what chips it has eaten.
>>>
>>> regards
>>> Antti
>>>
>>> --
>>> http://palosaari.fi/
>>>
>>> --
>>> To unsubscribe from this list: send the line "unsubscribe linux-media" in
>>> the body of a message to majordomo@vger.kernel.org
>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
>
> --
> http://palosaari.fi/
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Terratec H7 with yet another usb ID
2014-12-05 16:27 ` Eddi De Pieri
@ 2014-12-06 15:40 ` Olli Salonen
0 siblings, 0 replies; 6+ messages in thread
From: Olli Salonen @ 2014-12-06 15:40 UTC (permalink / raw)
To: Eddi De Pieri; +Cc: Antti Palosaari, Rik van Mierlo, linux-media
Hi Eddi,
As far as I know, the new version of Terratec H7 is another version of
DVBSky T680CI or TechnoTrend CT2-4650 CI. Just try to change the USB
IDs in the dvbsky.c driver and compile the driver and test. I'd do
this for you, but am travelling at the moment and have very limited
time.
Cheers,
-olli
On 5 December 2014 at 23:27, Eddi De Pieri <eddi@depieri.net> wrote:
> Hi Rik,
>
>
> I've download Terratec H7 rev 4 should be a
> TechnoTrend_TT-TVStick_CT2-44xx clone so you could try to patch
> dvbsky.c driver.
>
> Strings inside the windows driver:
> T E R R A T E C S 7 D i g i t a l T u n e r ( D V B - S / S 2 )
> T T - c o n n e c t C T 2 _ 4 6 5 0 D V B - T / T 2 T u n e r
> T E R R A T E C H 7 D i g i t a l T u n e r ( D V B - T / T 2 )
> T T - c o n n e c t C T 2 _ 4 6 5 0 D V B - C T u n e r
> T E R R A T E C H 7 D i g i t a l T u n e r ( D V B - C )
>
> Regards...
> Eddi
>
> On Fri, Dec 5, 2014 at 4:11 PM, Antti Palosaari <crope@iki.fi> wrote:
>> Moikka
>> Take USB sniffs and generate driver C-code from that sniff. Then copy&paste
>> that code to driver until is starts working. After that, you could remove
>> all the code until you find minimum set of needed changes (error and trial).
>>
>> regards
>> Antti
>>
>>
>> On 12/05/2014 04:51 PM, Eddi De Pieri wrote:
>>>
>>> Hi,
>>>
>>> I got a sample usb tuner with similar issue with following
>>> vendor/product 13d3:0ccd.
>>>
>>> Onboard it have: CY7C68013A-56PVXC and a SI2168-40. The tuner isn't
>>> visible since is covered by a shield.
>>>
>>> I've tried to patch the az6007 to make it working.
>>>
>>> si2168 4-0064: Silicon Labs Si2168 successfully attached
>>> si2157 5-0060: unknown chip version Si2147-A30
>>>
>>> after applying latest patch from patchwork:
>>>
>>> si2157 5-0060: Silicon Labs Si2157/Si2158 successfully attached
>>>
>>> Now tuner seems to be connected but a w_scan don't detect any channel...
>>>
>>> Can you give me some some hint on troubleshooting this issue?
>>>
>>> Actually I'm brutally changed the initialization with copy and paste
>>> of silab attach from cxusb.c and em28xx-dvb.c by removing the drxk
>>> init..
>>>
>>> Since the chinese producer recicled old vid/pid.but what is the
>>> correct way to probe for multiple frontend and choose the right one?
>>>
>>> Eddi
>>>
>>>
>>> On Mon, Feb 3, 2014 at 11:33 PM, Antti Palosaari <crope@iki.fi> wrote:
>>>>
>>>> Hei Rik
>>>>
>>>>
>>>> On 03.02.2014 22:21, Rik van Mierlo wrote:
>>>>>
>>>>>
>>>>> Hi,
>>>>>
>>>>> I've recently purchased a Terratec H7, based on the fact that is was
>>>>> supported for a while now. Unfortunately, it turns out that my device
>>>>> uses a different product id, and maybe is not quite the same device
>>>>> inside either.
>>>>>
>>>>> ProductID for the Terratec H7 revisions in the module is either 10b4 or
>>>>> 10a3, the one I purchased is 10a5. Following this patch:
>>>>>
>>>>> https://patchwork.linuxtv.org/patch/9691
>>>>>
>>>>> I modified drivers/media/usb/dvb-usb-v2/az6007.c to include an
>>>>> additional device:
>>>>>
>>>>> static struct usb_device_id az6007_usb_table[] = {
>>>>> {DVB_USB_DEVICE(USB_VID_AZUREWAVE, USB_PID_AZUREWAVE_6007,
>>>>> &az6007_props, "Azurewave 6007", RC_MAP_EMPTY)},
>>>>> {DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7,
>>>>> &az6007_props, "Terratec H7",
>>>>> RC_MAP_NEC_TERRATEC_CINERGY_XS)},
>>>>> {DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7_2,
>>>>> &az6007_props, "Terratec H7",
>>>>> RC_MAP_NEC_TERRATEC_CINERGY_XS)},
>>>>> {DVB_USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_H7_3,
>>>>> &az6007_props, "Terratec H7",
>>>>> RC_MAP_NEC_TERRATEC_CINERGY_XS)},
>>>>> {DVB_USB_DEVICE(USB_VID_TECHNISAT,
>>>>> USB_PID_TECHNISAT_USB2_CABLESTAR_HDCI,
>>>>> &az6007_cablestar_hdci_props, "Technisat CableStar
>>>>> Combo HD CI", RC_MAP_EMPTY)},
>>>>> {0},
>>>>> };
>>>>>
>>>>> and added the following to drivers/media/dvb-core/dvb-usb-ids.h
>>>>>
>>>>> #define USB_PID_TERRATEC_H7_3 0x10a5
>>>>>
>>>>> and recompiled/installed the kernel and modules. The module seems to
>>>>> have changed somewhat in 3.12.6 from the version that the patch was
>>>>> meant for, so I hope I this was all I had to change.
>>>>>
>>>>> Rebooting and plugging in the device now at least leads to a recognized
>>>>> device, but scanning for channels with w_scan does not work, and from
>>>>> the dmesg output below, it seems something is not working after loading
>>>>> the drxk firmware. Does anybody know what I could try next to get this
>>>>> device working? Could it be that the drxk firmware is not suitable for
>>>>> this revision of the device?
>>>>>
>>>>> [ 700.112072] usb 4-2: new high-speed USB device number 2 using
>>>>> ehci-pci
>>>>> [ 700.245092] usb 4-2: New USB device found, idVendor=0ccd,
>>>>> idProduct=10a5
>>>>> [ 700.245105] usb 4-2: New USB device strings: Mfr=1, Product=2,
>>>>> SerialNumber=3
>>>>> [ 700.245114] usb 4-2: Product: TERRATEC T2/T/C CI USB
>>>>> [ 700.245123] usb 4-2: Manufacturer: TERRATEC
>>>>> [ 700.245131] usb 4-2: SerialNumber: 20130903
>>>>> [ 700.494693] usb read operation failed. (-32)
>>>>> [ 700.495039] usb write operation failed. (-32)
>>>>> [ 700.495413] usb write operation failed. (-32)
>>>>> [ 700.495787] usb write operation failed. (-32)
>>>>
>>>>
>>>>
>>>> These low level errors does not promise any good. Are these coming from
>>>> USB
>>>> stack as there is no even bus ID (4-2)...
>>>>
>>>>> [ 700.495800] usb 4-2: dvb_usb_v2: found a 'Terratec H7' in cold state
>>>>> [ 700.507381] usb 4-2: firmware: direct-loading firmware
>>>>> dvb-usb-terratec-h7-az6007.fw
>>>>> [ 700.507397] usb 4-2: dvb_usb_v2: downloading firmware from file
>>>>> 'dvb-usb-terratec-h7-az6007.fw'
>>>>> [ 700.524301] usb 4-2: dvb_usb_v2: found a 'Terratec H7' in warm state
>>>>> [ 701.760878] usb 4-2: dvb_usb_v2: will pass the complete MPEG2
>>>>> transport stream to the software demuxer
>>>>> [ 701.760947] DVB: registering new adapter (Terratec H7)
>>>>> [ 701.763853] usb 4-2: dvb_usb_v2: MAC address: c2:cd:0c:a5:10:00
>>>>> [ 701.846469] drxk: frontend initialized.
>>>>> [ 701.849123] usb 4-2: firmware: direct-loading firmware
>>>>> dvb-usb-terratec-h7-drxk.fw
>>>>> [ 701.849215] usb 4-2: DVB: registering adapter 0 frontend 0 (DRXK)...
>>>>> [ 701.881072] drxk: status = 0x00c04125
>>>>> [ 701.881082] drxk: DeviceID 0x04 not supported
>>>>> [ 701.881090] drxk: Error -22 on init_drxk
>>>>
>>>>
>>>>
>>>> I suspect there is no DRX-K.
>>>>
>>>>> [ 701.908184] mt2063_attach: Attaching MT2063
>>>>> [ 701.940248] Registered IR keymap rc-nec-terratec-cinergy-xs
>>>>> [ 701.940547] input: Terratec H7 as
>>>>> /devices/pci0000:00/0000:00:1d.7/usb4/4-2/rc/rc0/input16
>>>>> [ 701.942559] rc0: Terratec H7 as
>>>>> /devices/pci0000:00/0000:00:1d.7/usb4/4-2/rc/rc0
>>>>> [ 701.942575] usb 4-2: dvb_usb_v2: schedule remote query interval to
>>>>> 400 msecs
>>>>> [ 701.942587] usb 4-2: dvb_usb_v2: 'Terratec H7' successfully
>>>>> initialized and connected
>>>>> [ 701.942643] usbcore: registered new interface driver dvb_usb_az6007
>>>>
>>>>
>>>>
>>>> hmm, a little bit surprising that driver accepts hardware even those
>>>> fatal
>>>> errors.
>>>>
>>>> My guess is that there is no DRX-K but some other demod or likely more
>>>> changed chips than demod. DRX-K is rather old demod and there is not very
>>>> many newer alternatives on the market. Silicon Labs chipset ? Open the
>>>> device in look what chips it has eaten.
>>>>
>>>> regards
>>>> Antti
>>>>
>>>> --
>>>> http://palosaari.fi/
>>>>
>>>> --
>>>> To unsubscribe from this list: send the line "unsubscribe linux-media" in
>>>> the body of a message to majordomo@vger.kernel.org
>>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>
>>
>> --
>> http://palosaari.fi/
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2014-12-06 15:40 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-02-03 20:21 Terratec H7 with yet another usb ID Rik van Mierlo
2014-02-03 22:33 ` Antti Palosaari
2014-12-05 14:51 ` Eddi De Pieri
2014-12-05 15:11 ` Antti Palosaari
2014-12-05 16:27 ` Eddi De Pieri
2014-12-06 15:40 ` Olli Salonen
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.