linux-imx_3.10.17 locks up hard at boot

All of lore.kernel.org
 help / color / mirror / Atom feed

* linux-imx_3.10.17 locks up hard at boot
@ 2014-03-07 14:15 Boszormenyi Zoltan
  2014-03-07 14:20 ` Daiane.Angolini
  0 siblings, 1 reply; 7+ messages in thread
From: Boszormenyi Zoltan @ 2014-03-07 14:15 UTC (permalink / raw)
  To: meta-freescale

Hi,

I have forced kernel version 3.10.17 to test it and it seems to
lock up as soon as it wants to start X. The serial console
reaches the login prompt but nothing I type is echoed back
and the board doesn't respond to ping. The KMS graphical boot
is shown but the screen turns all black around the same time
the login prompt is shown in the serial console and the display
says "no signal". Is there a known problem with this kernel version?
gpu-viv-bin-mx6q-3.10.17-1.0.0-beta-hfp ("hardfp") was built.

Can someone point me to a solution to having a working kernel
that's more recent than 3.0.35?

I use a Freescale board that's labeled MCIMX6Q-SDB.

Thanks in advance,
Zoltán Böszörményi

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: linux-imx_3.10.17 locks up hard at boot
  2014-03-07 14:15 linux-imx_3.10.17 locks up hard at boot Boszormenyi Zoltan
@ 2014-03-07 14:20 ` Daiane.Angolini
       [not found]   ` <5319DA9C.9040106@pr.hu>
  0 siblings, 1 reply; 7+ messages in thread
From: Daiane.Angolini @ 2014-03-07 14:20 UTC (permalink / raw)
  To: Boszormenyi Zoltan, meta-freescale@yoctoproject.org



> -----Original Message-----
> From: meta-freescale-bounces@yoctoproject.org [mailto:meta-freescale-
> bounces@yoctoproject.org] On Behalf Of Boszormenyi Zoltan
> Sent: Friday, March 07, 2014 11:16 AM
> To: meta-freescale@yoctoproject.org
> Subject: [meta-freescale] linux-imx_3.10.17 locks up hard at boot
> 
> Hi,
> 
> I have forced kernel version 3.10.17 to test it and it seems to lock up as
> soon as it wants to start X. The serial console reaches the login prompt
> but nothing I type is echoed back and the board doesn't respond to ping.


How do you know the board IP to ping?

> The KMS graphical boot is shown but the screen turns all black around the

Which screen?
Are you using LVDS? HDMI?

> same time the login prompt is shown in the serial console and the display
> says "no signal". Is there a known problem with this kernel version?

I have no idea =D

Do you have any log?

Which image you´re using?

What branch?

> gpu-viv-bin-mx6q-3.10.17-1.0.0-beta-hfp ("hardfp") was built.
> 
> Can someone point me to a solution to having a working kernel that's more
> recent than 3.0.35?

You can use kernel mainline.

> 
> I use a Freescale board that's labeled MCIMX6Q-SDB.

What machine you used in your local.conf?

> 
> Thanks in advance,
> Zoltán Böszörményi

Daiane


^ permalink raw reply	[flat|nested] 7+ messages in thread

[parent not found: <5319DA9C.9040106@pr.hu>]

* Re: linux-imx_3.10.17 locks up hard at boot
       [not found]   ` <5319DA9C.9040106@pr.hu>
@ 2014-03-07 14:48     ` Boszormenyi Zoltan
  2014-03-07 14:57       ` Otavio Salvador
  0 siblings, 1 reply; 7+ messages in thread
From: Boszormenyi Zoltan @ 2014-03-07 14:48 UTC (permalink / raw)
  To: meta-freescale@yoctoproject.org

[-- Attachment #1: Type: text/plain, Size: 3011 bytes --]

Adding back the list.

2014-03-07 15:41 keltezéssel, Boszormenyi Zoltan írta:
> 2014-03-07 15:20 keltezéssel, Daiane.Angolini@freescale.com írta:
>>
>>> -----Original Message-----
>>> From: meta-freescale-bounces@yoctoproject.org [mailto:meta-freescale-
>>> bounces@yoctoproject.org] On Behalf Of Boszormenyi Zoltan
>>> Sent: Friday, March 07, 2014 11:16 AM
>>> To: meta-freescale@yoctoproject.org
>>> Subject: [meta-freescale] linux-imx_3.10.17 locks up hard at boot
>>>
>>> Hi,
>>>
>>> I have forced kernel version 3.10.17 to test it and it seems to lock up as
>>> soon as it wants to start X. The serial console reaches the login prompt
>>> but nothing I type is echoed back and the board doesn't respond to ping.
>>
>> How do you know the board IP to ping?
>
> The serial console has this:
>
> Configuring network interfaces... fec 2188000.ethernet eth0: Freescale FEC PHY driver 
> [Generic PHY] (mii_bus:phy_addr=2188000.ethernet:01, irq=-1)
> IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
> udhcpc (v1.22.1) started
> Sending discover...
> Sending discover...
> libphy: 2188000.ethernet:01 - Link is Up - 1000/Full
> IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> Sending discover...
> Sending select for 192.168.1.7...
> Lease of 192.168.1.7 obtained, lease time 86400
> /etc/udhcpc.d/50default: Adding DNS 8.8.8.8
> /etc/udhcpc.d/50default: Adding DNS 87.242.0.10
> done.
>
> So, somewhat obvious. :-)
>
>>
>>> The KMS graphical boot is shown but the screen turns all black around the
>> Which screen?
>
> A big text (obviously in graphics mode so not 80x25 or something
> larger but still character console) saying
>
> "yocto
>  project"
>
> and a progress bar in the middle of the lower part of the screen.
> Something similar to what Fedora has with its plymouth boot splash.
>
>> Are you using LVDS? HDMI?
>
> HDMI. The boot image with the Freescale logo is also shown
> before the boot splash of yocto.
>
>>
>>> same time the login prompt is shown in the serial console and the display
>>> says "no signal". Is there a known problem with this kernel version?
>> I have no idea =D
>
> :-)
>
>> Do you have any log?
>
> I copy&pasted from my minicom and attached.
>
>>
>> Which image you´re using?
>
> core-image-x11
>
>>
>> What branch?
>
> master-next
>
>>
>>> gpu-viv-bin-mx6q-3.10.17-1.0.0-beta-hfp ("hardfp") was built.
>>>
>>> Can someone point me to a solution to having a working kernel that's more
>>> recent than 3.0.35?
>> You can use kernel mainline.
>
> 3.13.x or 3.14 GIT?
> Will the X11 driver give me accelerated graphics with these kernels?
>
>>
>>> I use a Freescale board that's labeled MCIMX6Q-SDB.
>> What machine you used in your local.conf?
>
> imx6qsabresd
>
> The same machine with branch "dora" and even master-next
> but with kernel 3.0.35 and I can e.g. login via the serial console.
>
>>
>>> Thanks in advance,
>>> Zoltán Böszörményi
>> Daiane
>>
>


[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #2: lockup.log --]
[-- Type: text/x-log; name="lockup.log", Size: 18900 bytes --]

U-Boot 2014.01 (Mar 07 2014 - 14:16:56)

CPU:   Freescale i.MX6Q rev1.1 at 792 MHz
Reset cause: POR
Board: MX6-SabreSD
DRAM:  1 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
auto-detected panel HDMI
Display: HDMI (1024x768)
In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0 
mmc1 is current device
reading boot.scr
** Unable to read file boot.scr **
reading uImage
5165360 bytes read in 284 ms (17.3 MiB/s)
Booting from mmc ...
reading imx6q-sabresd.dtb
46300 bytes read in 19 ms (2.3 MiB/s)
## Booting kernel from Legacy Image at 12000000 ...
   Image Name:   Linux-3.10.17-1.0.0_beta+gec1af9
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    5165296 Bytes = 4.9 MiB
   Load Address: 10008000
   Entry Point:  10008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 18000000
   Booting using the fdt blob at 0x18000000
   Loading Kernel Image ... OK
   Using Device Tree in place at 18000000, end 1800e4db

Starting kernel ...

Booting Linux on physical CPU 0x0
Linux version 3.10.17-1.0.0_beta+gec1af9f (zozo@localhost.localdomain) (gcc version 4.8.2 (GCC) ) #1 SMP Fri Mar 7 14:09:37 CET 2014
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Freescale i.MX6 Quad/DualLite (Device Tree), model: Freescale i.MX6 Quad SABRE Smart Device Board
cma: CMA: reserved 256 MiB at 40000000
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 8 pages/cpu @814f1000 s8704 r8192 d15872 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260096
Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw video=mxcfb0:dev=hdmi,1920x1080M@60,if=RGB24,bpp=32 consoleblank=0 vt.global_cursor_default=0
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1024MB = 1024MB total
Memory: 763500k/763500k available, 285076k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xc0800000 - 0xff000000   (1000 MB)
    lowmem  : 0x80000000 - 0xc0000000   (1024 MB)
    modules : 0x7f000000 - 0x80000000   (  16 MB)
      .text : 0x80008000 - 0x80bdb594   (12110 kB)
      .init : 0x80bdc000 - 0x80c26200   ( 297 kB)
      .data : 0x80c28000 - 0x80c76320   ( 313 kB)
       .bss : 0x80c76320 - 0x80cdabe4   ( 403 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x32070000, Cache size: 1048576 B
sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
CPU identified as i.MX6Q, silicon rev 1.1
Console: colour dummy device 80x30
Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x806173a0 - 0x806173f8
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU2: Booted secondary processor
CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
CPU3: Booted secondary processor
CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
Brought up 4 CPUs
SMP: Total of 4 processors activated (6324.22 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
pinctrl core: initialized pinctrl subsystem
regulator-dummy: no parameters
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
Use WDOG2 as reset source
syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered
vdd1p1: 800 <--> 1375 mV at 1125 mV 
vdd3p0: 2800 <--> 3150 mV at 3000 mV 
vdd2p5: 2000 <--> 2750 mV at 2425 mV 
cpu: 725 <--> 1450 mV at 1100 mV 
vddpu: 725 <--> 1450 mV at 1100 mV 
vddsoc: 725 <--> 1450 mV at 1175 mV 
syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered
syscon 21bc000.ocotp-ctrl: regmap [mem 0x021bc000-0x021bffff] registered
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
bio: create slab <bio-0> at 0
mxs-dma 110000.dma-apbh: initialized
usb_otg_vbus: 5000 mV 
usb_h1_vbus: 5000 mV 
wm8962-supply: no parameters
mipi_dsi_pwr_on: no parameters
sensor-supply: 3300 mV 
i2c-core: driver [max17135] using legacy suspend method
i2c-core: driver [max17135] using legacy resume method
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c i2c-0: IMX I2C adapter registered
i2c i2c-1: IMX I2C adapter registered
i2c i2c-2: IMX I2C adapter registered
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
imx-ipuv3 2800000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 driver probed
mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 dphy version is 0x3130302a
MIPI CSI2 driver module loaded
Advanced Linux Sound Architecture Driver Initialized.
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource mxc_timer1
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
pureg-dummy: no parameters
imx6_busfreq busfreq.13: DDR medium rate not supported.
Bus freq driver module loaded
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
jffs2: version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
fuse init (API version 7.22)
msgmni has been set to 2003
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
imx-weim 21b8000.weim: WEIM driver registered.
mxc_mipi_dsi 21e0000.mipi: i.MX MIPI DSI driver probed
MIPI DSI driver module loaded
mxc_sdc_fb fb.26: register mxc display driver hdmi
mxc_hdmi 20e0000.hdmi_video: Detected HDMI controller 0x13:0xa:0xa0:0xc1
fbcvt: 1920x1080@60: CVT Name - 2.073M9
imx-ipuv3 2400000.ipu: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
Console: switching to colour frame buffer device 240x67
mxc_sdc_fb fb.27: register mxc display driver hdmi
mxc_hdmi 20e0000.hdmi_video: Error only one HDMI output support now!
mxc_sdc_fb fb.27: NO mxc display driver found!
mxc_sdc_fb fb.28: register mxc display driver lcd
mxc_sdc_fb fb.28: ipu0-di0 already in use
mxc_sdc_fb: probe of fb.28 failed with error -16
mxc_sdc_fb fb.29: register mxc display driver ldb
imx-sdma 20ec000.sdma: no iram assigned, using external mem
imx-sdma 20ec000.sdma: loaded firmware 1.1
imx-sdma 20ec000.sdma: initialized
fbcvt: 1920x1080@60: CVT Name - 2.073M9
pfuze100-regulator 1-0008: Illegal ID: 11
pfuze100-regulator 1-0008: unrecognized pfuze chip ID!
Serial: IMX driver
2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
console [ttymxc0] enabled
serial: Freescale lpuart driver
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized vivante 1.0.0 20120216 on minor 0
brd: module loaded
loop: module loaded
ahci: SSS flag set, parallel bus scan disabled
ahci ahci: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
ahci ahci: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst 
scsi0 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 71
m25p80 spi32766.0: found mr25h256, expected m25p32
m25p80 spi32766.0: mr25h256 (32 Kbytes)
spi_imx 2008000.ecspi: probed
CAN device driver interface
libphy: fec_enet_mii_bus: probed
fec 2188000.ethernet eth0: registered PHC device 0
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
usbcore: registered new interface driver usb-storage
imx_usb 2184000.usb: usbmisc init failed, ret=-517
platform 2184000.usb: Driver imx_usb requests probe deferral
imx_usb 2184200.usb: usbmisc init failed, ret=-517
platform 2184200.usb: Driver imx_usb requests probe deferral
mousedev: PS/2 mouse device common for all mice
elan-touch 2-0010: elan - Read Hello Packet Failed
elan-touch: probe of 2-0010 failed with error -22
egalax_ts 1-0004: Failed to read firmware version
egalax_ts: probe of 1-0004 failed with error -5
ata1: SATA link down (SStatus 0 SControl 300)
egalax_ts 2-0004: Failed to read firmware version
egalax_ts: probe of 2-0004 failed with error -5
input: max11801_ts as /devices/soc0/soc.1/2100000.aips-bus/21a4000.i2c/i2c-1/1-0048/input/input0
i2c-core: driver [isl29023] using legacy suspend method
i2c-core: driver [isl29023] using legacy resume method
snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc0
i2c /dev entries driver
mxc_v4l2_output v4l2_out.34: V4L2 device registered as video16
mxc_v4l2_output v4l2_out.34: V4L2 device registered as video17
mxc_v4l2_output v4l2_out.34: V4L2 device registered as video18
mxc_v4l2_output v4l2_out.34: V4L2 device registered as video19
mag3110 2-000e: check mag3110 chip ID
input: mag3110 as /devices/virtual/input/input1
mag3110 2-000e: mag3110 is probed
i2c-core: driver [mag3110] using legacy suspend method
i2c-core: driver [mag3110] using legacy resume method
input: mma845x as /devices/virtual/input/input2
imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0)
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: no vqmmc regulator found
mmc0: no vmmc regulator found
mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
mmc1: no vqmmc regulator found
mmc1: no vmmc regulator found
mmc1: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA
mmc2: no vqmmc regulator found
mmc2: no vmmc regulator found
mmc2: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA
mmc1: new high speed SD card at address b368
mmcblk0: mmc1:b368 SDC   1.91 GiB 
 mmcblk0: p1 p2
mmc2: new high speed DDR MMC card at address 0001
mmcblk1: mmc2:0001 SEM08G 7.39 GiB 
mmcblk1boot0: mmc2:0001 SEM08G partition 1 2.00 MiB
Galcore version 4.6.9.9754
mmcblk1boot1: mmc2:0001 SEM08G partition 2 2.00 MiB
mmcblk1rpmb: mmc2:0001 SEM08G partition 3 128 KiB
 mmcblk1: p1 p2 p3 < p5 p6 p7 > p4
 mmcblk1boot1: unknown partition table
 mmcblk1boot0: unknown partition table
mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
mxc_asrc 2034000.asrc: mxc_asrc registered
mxc_vpu 2040000.vpu: VPU initialized
caam 2100000.caam: device ID = 0x0a16010000000000 (Era -524)
caam 2100000.caam: job rings = 2, qi = 0
caam 2100000.caam: authenc-hmac-md5-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-aes-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-aes-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-aes-caam
caam 2100000.caam: authenc-hmac-md5-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-des3_ede-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-des3_ede-caam
caam 2100000.caam: authenc-hmac-md5-cbc-des-caam
caam 2100000.caam: authencesn-hmac-md5-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha1-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha1-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha224-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha224-cbc-des-caam
caam 2100000.caam: authenc-hmac-sha256-cbc-des-caam
caam 2100000.caam: authencesn-hmac-sha256-cbc-des-caam
caam 2100000.caam: ecb-des-caam
caam 2100000.caam: ecb-arc4-caam
caam 2100000.caam: ecb-aes-caam
caam 2100000.caam: ctr-aes-caam
caam 2100000.caam: cbc-aes-caam
caam 2100000.caam: ecb-des3-caam
caam 2100000.caam: cbc-3des-caam
caam 2100000.caam: cbc-des-caam
caam 2100000.caam: fsl,sec-v4.0 algorithms registered in /proc/crypto
platform 2101000.jr0: registering rng-caam
platform caam_sm: caam_sm_test: 8-byte key test match OK
platform caam_sm: caam_sm_test: 16-byte key test match OK
platform caam_sm: caam_sm_test: 32-byte key test match OK
platform caam_secvio.36: security violation service handlers armed
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
i2c-core: driver [cs42888] using legacy suspend method
i2c-core: driver [cs42888] using legacy resume method
wm8962 0-001a: customer id 0 revision D
input: WM8962 Beep Generator as /devices/soc0/soc.1/2100000.aips-bus/21a0000.i2c/i2c-0/0-001a/input/input3
imx-wm8962 sound.24:  wm8962 <-> 202c000.ssi mapping ok
input: wm8962-audio AMIC as /devices/soc0/sound.24/sound/card0/input4
input: wm8962-audio Headphone Jack as /devices/soc0/sound.24/sound/card0/input5
imx-audio-hdmi sound-hdmi.25:  hdmi-hifi <-> hdmi_audio.14 mapping ok
TCP: cubic registered
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
imx6-cpufreq imx6-cpufreq.0: failed to get regulators
imx6-cpufreq: probe of imx6-cpufreq.0 failed with error -2
vddpu: disabling
ci_hdrc ci_hdrc.1: doesn't support gadget
ci_hdrc ci_hdrc.1: EHCI Host Controller
max8903-charger max8903.16: USB Charger Connected.
ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
max8903-charger max8903.16: USB Charger Disconnected.
ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
input: gpio-keys.23 as /devices/soc0/gpio-keys.23/input/input6
snvs_rtc 20cc034.snvs-rtc-lp: setting system clock to 1970-01-01 00:00:01 UTC (1)
ALSA device list:
  #0: wm8962-audio
  #1: imx-hdmi-soc
kjournald starting.  Commit interval 5 seconds
EXT3-fs (mmcblk0p2): using internal journal
EXT3-fs (mmcblk0p2): recovery complete
EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
VFS: Mounted root (ext3 filesystem) on device 179:2.
devtmpfs: mounted
Freeing unused kernel memory: 296K (80bdc000 - 80c26000)
INIT: version 2.88 booting
Starting udev
udevd[182]: starting version 182
ov5640_power_on: cannot get io voltage error
ov5640_power_on: cannot get core voltage error
ov5640 0-003c: cannot get io voltage
ov5640 0-003c: cannot get core voltage
ov5640 0-003c: cannot get analog voltage
ov5640_power_on: cannot get analog voltage error
ov5640_read_reg:write reg error:reg=300a
camera ov5640 is not found
ov5640_read_reg:write reg error:reg=300a
camera ov5640_mipi is not found
Starting Bootlog daemon: bootlogd: cannot allocate pseudo ov5642_power_on: cannot get io voltage error
tty: No such file or directory
bov5642_power_on: cannot get core voltage error
ootlogd.
ov5642_power_on: cannot get analog voltage error
ov5642_read_reg:write reg error:reg=300a
camera ov5642 is not found
EXT4-fs (mmcblk1p5): recovery complete
EXT4-fs (mmcblk1p6): warning: maximal mount count reached, running e2fsck is recommended
FAT-fs (mmcblk1p4): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
EXT4-fs (mmcblk1p6): recovery complete
EXT4-fs (mmcblk1p6): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (mmcblk1p5): mounted filesystem with ordered data mode. Opts: (null)
ALSA: Restoring mixer settings...
FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
Found hardware: "wm8962-audio" "" "" "" ""
Hardware is initializEXT4-fs (mmcblk1p7): warning: maximal mount count reached, running e2fsck is recommended
ed using a generic method
EXT4-fs (mmcblk1p7): recovery complete
No state is present for card imxhEXT4-fs (mmcblk1p7): mounted filesystem with ordered data mode. Opts: (null)
dmisoc
Found hardware: "imx-hdmi-soc" "" "" "" ""
Hardware is initialized using a generic method
No state is present for card imxhdmisoc
INIT: Entering runlevel: 5
Configuring network interfaces... fec 2188000.ethernet eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=2188000.ethernet:01, irq=-1)
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc (v1.22.1) started
Sending discover...
Sending discover...
libphy: 2188000.ethernet:01 - Link is Up - 1000/Full
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Sending discover...
Sending select for 192.168.1.7...
Lease of 192.168.1.7 obtained, lease time 86400
/etc/udhcpc.d/50default: Adding DNS 8.8.8.8
/etc/udhcpc.d/50default: Adding DNS 87.242.0.10
done.
Starting Xserver
Starting system message bus: dbus.
Starting rpcbind daemon...done.
Starting advanced power management daemon: No APM support in kernel
(failed.)
Starting syslogd/klogd: done
 * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
   ...done.
Starting Telephony daemon
Starting Linux NFC daemon
Stopping Bootlog daemon: bootlogd.

Poky (Yocto Project Reference Distro) 1.5+snapshot-20140307 imx6qsabresd /dev/ttymxc0

imx6qsabresd login: 

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: linux-imx_3.10.17 locks up hard at boot
  2014-03-07 14:48     ` Boszormenyi Zoltan
@ 2014-03-07 14:57       ` Otavio Salvador
  2014-03-07 16:25         ` Boszormenyi Zoltan
  0 siblings, 1 reply; 7+ messages in thread
From: Otavio Salvador @ 2014-03-07 14:57 UTC (permalink / raw)
  To: Boszormenyi Zoltan; +Cc: meta-freescale@yoctoproject.org

Hello,

On Fri, Mar 7, 2014 at 11:48 AM, Boszormenyi Zoltan <zboszor@pr.hu> wrote:
...
>>> What branch?
>>
>>
>> master-next

Please do:

printenv fdtfile

in U-Boot.

-- 
Otavio Salvador                             O.S. Systems
http://www.ossystems.com.br        http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854            Mobile: +1 (347) 903-9750


^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: linux-imx_3.10.17 locks up hard at boot
  2014-03-07 14:57       ` Otavio Salvador
@ 2014-03-07 16:25         ` Boszormenyi Zoltan
  2014-03-07 16:44           ` Otavio Salvador
  0 siblings, 1 reply; 7+ messages in thread
From: Boszormenyi Zoltan @ 2014-03-07 16:25 UTC (permalink / raw)
  To: Otavio Salvador; +Cc: meta-freescale@yoctoproject.org

2014-03-07 15:57 keltezéssel, Otavio Salvador írta:
> printenv fdtfile

=> printenv fdtfile
## Error: "fdtfile" not defined

The full set of environment is below.
You might have meant "fdt_file", it's listed.

=> printenv
baudrate=115200
boot_fdt=try
bootcmd=mmc dev ${mmcdev};if mmc rescan; then if run loadbootscript; then run bootscript; 
else if run loaduimage; then run mmcboot; else run netboot; fi; fi; else run netboot; fi
bootdelay=4
bootscript=echo Running bootscript from mmc ...; source
console=ttymxc0
emmcdev=2
ethact=FEC
ethaddr=00:04:9f:02:34:c2
ethprime=FEC
fdt_addr=0x18000000
fdt_file=imx6q-sabresd.dtb
fdt_high=0xffffffff
initrd_high=0xffffffff
ip_dyn=yes
loadaddr=0x12000000
loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};
loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}
loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}
mmcargs=setenv bootargs console=${console},${baudrate} root=${mmcroot} video=${video} 
consoleblank=0 vt.global_cursor_default=0
mmcboot=echo Booting from mmc ...; run mmcargs; if test ${boot_fdt} = yes || test 
${boot_fdt} = try; then if run loadfdt; then bootm ${loadaddr} - ${fdt_addr}; else if test 
${boot_fdt} = try; then bootm; else echo WARN: Cannot load ;
mmcdev=1
mmcpart=1
mmcroot=/dev/mmcblk0p2 rootwait rw
netargs=setenv bootargs console=${console},${baudrate} root=/dev/nfs ip=dhcp 
nfsroot=${serverip}:${nfsroot},v3,tcp
netboot=echo Booting from net ...; run netargs; if test ${ip_dyn} = yes; then setenv 
get_cmd dhcp; else setenv get_cmd tftp; fi; ${get_cmd} ${uimage}; if test ${boot_fdt} = 
yes || test ${boot_fdt} = try; then if ${get_cmd} ${fdt_add;
script=boot.scr
uimage=uImage
update_emmc_firmware=if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else setenv 
get_cmd tftp; fi; if ${get_cmd} ${update_sd_firmware_filename}; then if mmc dev ${emmcdev} 
&& mmc open ${emmcdev} 1; then setexpr fw_sz ${filesize} i
update_sd_firmware=if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else setenv get_cmd 
tftp; fi; if mmc dev ${mmcdev}; then if ${get_cmd} ${update_sd_firmware_filename}; then 
setexpr fw_sz ${filesize} / 0x200; setexpr fw_sz ${fw_i
video=mxcfb0:dev=hdmi,1920x1080M@60,if=RGB24,bpp=32
video_hdmi=mxcfb0:dev=hdmi,1920x1080M@60,if=RGB24,bpp=32
video_lvds=mxcfb0:dev=ldb,LDB-LG,if=RGB24,bpp=32 ldb=spl0

Environment size: 2510/8188 bytes

Best regards,
Zoltán Böszörményi



^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: linux-imx_3.10.17 locks up hard at boot
  2014-03-07 16:25         ` Boszormenyi Zoltan
@ 2014-03-07 16:44           ` Otavio Salvador
  2014-03-07 17:22             ` Boszormenyi Zoltan
  0 siblings, 1 reply; 7+ messages in thread
From: Otavio Salvador @ 2014-03-07 16:44 UTC (permalink / raw)
  To: Boszormenyi Zoltan; +Cc: meta-freescale@yoctoproject.org

Hello,

On Fri, Mar 7, 2014 at 1:25 PM, Boszormenyi Zoltan <zboszor@pr.hu> wrote:
> 2014-03-07 15:57 keltezéssel, Otavio Salvador írta:
>>
>> printenv fdtfile
>
>
> => printenv fdtfile
> ## Error: "fdtfile" not defined
>
> The full set of environment is below.
> You might have meant "fdt_file", it's listed.
...
> fdt_file=imx6q-sabresd.dtb
...

Use:

setenv fdt_file imx6q-sabresd-ldo.dtb

This is fixed in U-Boot 2014.01 update pending in master-next.

-- 
Otavio Salvador                             O.S. Systems
http://www.ossystems.com.br        http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854            Mobile: +1 (347) 903-9750


^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: linux-imx_3.10.17 locks up hard at boot
  2014-03-07 16:44           ` Otavio Salvador
@ 2014-03-07 17:22             ` Boszormenyi Zoltan
  0 siblings, 0 replies; 7+ messages in thread
From: Boszormenyi Zoltan @ 2014-03-07 17:22 UTC (permalink / raw)
  To: Otavio Salvador; +Cc: meta-freescale@yoctoproject.org

2014-03-07 17:44 keltezéssel, Otavio Salvador írta:
> Hello,
>
> On Fri, Mar 7, 2014 at 1:25 PM, Boszormenyi Zoltan <zboszor@pr.hu> wrote:
>> 2014-03-07 15:57 keltezéssel, Otavio Salvador írta:
>>> printenv fdtfile
>>
>> => printenv fdtfile
>> ## Error: "fdtfile" not defined
>>
>> The full set of environment is below.
>> You might have meant "fdt_file", it's listed.
> ...
>> fdt_file=imx6q-sabresd.dtb
> ...
>
> Use:
>
> setenv fdt_file imx6q-sabresd-ldo.dtb
>
> This is fixed in U-Boot 2014.01 update pending in master-next.

Thank you very much, it's fixed now.
X comes up, the machine can be pinged and the serial console responds.

Best regards,
Zoltán Böszörményi



^ permalink raw reply	[flat|nested] 7+ messages in thread

end of thread, other threads:[~2014-03-07 17:22 UTC | newest]

Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-03-07 14:15 linux-imx_3.10.17 locks up hard at boot Boszormenyi Zoltan
2014-03-07 14:20 ` Daiane.Angolini
     [not found]   ` <5319DA9C.9040106@pr.hu>
2014-03-07 14:48     ` Boszormenyi Zoltan
2014-03-07 14:57       ` Otavio Salvador
2014-03-07 16:25         ` Boszormenyi Zoltan
2014-03-07 16:44           ` Otavio Salvador
2014-03-07 17:22             ` Boszormenyi Zoltan

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.