[Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel

All of lore.kernel.org
 help / color / mirror / Atom feed

* [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
@ 2014-03-31 17:45 Lennart Sorensen
  2014-03-31 18:12 ` Gilles Chanteperdrix
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-03-31 17:45 UTC (permalink / raw)
  To: xenomai

I am trying to port xenomai 2.6.3 and ipipe to 3.12 kernel, since 3.8
keeps randomly screwing up sigchld handling and causing segfaults in
programs at random.  3.12 does not do this, so rather than spent a lot
of time tracking down the difference, I am moving forward instead.

I took the ipipe 3.11 git tree diff and applied it against 3.12.14,
and fixed up the issues I found in applying the patch (I think there is
one powerpc issue I commented out because I couldn't make sense of it,
but since I currently am playing with arm, I don't mind that).
I compiled and booted with IPIPE turned on, and it did not appear to
cause any problems.

I then applied the xenomai-2.6 git tree patches to the kernel, and fixed
up a few compile issues (mainly CONFIG_GENERIC_HARDIRQS is gone and is
to be assumed to always be on with new kernels).  This too boots, and
the xenomai modules load without crashing.

switchtest seems to run OK and does this:

root@omap5:~# /usr/lib/xenomai/testsuite/switchtest 
== Testing FPU check routines...
d0: 1 != 2
d1: 1 != 2
d2: 1 != 2
d3: 1 != 2
d4: 1 != 2
d5: 1 != 2
d6: 1 != 2
d7: 1 != 2
d8: 1 != 2
d9: 1 != 2
d10: 1 != 2
d11: 1 != 2
d12: 1 != 2
d13: 1 != 2
d14: 1 != 2
d15: 1 != 2
== FPU check routines: OK.
== Threads: sleeper_ufps0-0 rtk0-1 rtk0-2 rtk_fp0-3 rtk_fp0-4 rtk_fp_ufpp0-5 rtk_fp_ufpp0-6 rtup0-7 rtup0-8 rtup_ufpp0-9 rtup_ufpp0-10 rtus0-11 rtus0-12 rtus_ufps0-13 rtus_ufps0-14 rtuo0-15 rtuo0-16 rtuo_ufpp0-17 rtuo_ufpp0-18 rtuo_ufps0-19 rtuo_ufps0-20 rtuo_ufpp_ufps0-
21 rtuo_ufpp_ufps0-22 sleeper_ufps1-0 rtk1-1 rtk1-2 rtk_fp1-3 rtk_fp1-4 rtk_fp_ufpp1-5 rtk_fp_ufpp1-6 rtup1-7 rtup1-8 rtup_ufpp1-9 rtup_ufpp1-10 rtus1-11 rtus1-12 rtus_ufps1-13 rtus_ufps1-14 rtuo1-15 rtuo1-16 rtuo_ufpp1-17 rtuo_ufpp1-18 rtuo_ufps1-19 rtuo_ufps1-20 rtuo_u
fpp_ufps1-21 rtuo_ufpp_ufps1-22
RTT|  00:00:01
RTH|---------cpu|ctx switches|-------total
RTD|           1|       17041|       17041
RTD|           0|       17041|       17041
RTD|           1|       17043|       34084
RTD|           0|       16974|       34015
RTD|           1|       17045|       51129
RTD|           0|       17043|       51058
RTD|           1|       16974|       68103
RTD|           0|       16840|       67898
RTD|           0|        5033|       72931
RTD|           1|        5035|       73138
...

And /proc/xenomai/stat shows:
root@omap5:~# cat /proc/xenomai/stat 
CPU  PID    MSW        CSW        PF    STAT       %CPU  NAME
  0  0      0          6271365    0     00500080   94.2  ROOT/0
  1  0      0          6288303    0     00500088   94.2  ROOT/1
  0  4501   1          1          0     00b00380    0.0  switchtest
  0  0      0          2929       0     00004082    0.0  rtk1/0
  0  0      0          2929       0     00004082    0.0  rtk2/0
  0  0      0          2929       0     00104082    0.0  rtk3/0
  0  0      0          2929       0     00104082    0.0  rtk4/0
  0  0      0          2929       0     00104082    0.0  rtk5/0
  0  0      0          2929       0     00104082    0.0  rtk6/0
  0  4505   2          2931       0     00304182    0.0  rtup0-7
  0  4506   2          2931       0     00304182    0.0  rtup0-8
  0  4507   2          2931       0     00304182    0.0  rtup_ufpp0-9
  0  4508   2          2931       0     00304182    0.0  rtup_ufpp0-10
  0  4509   3          3          0     00300380    0.0  rtus0-11
  0  4510   3          3          0     00300380    0.0  rtus0-12
  0  4511   3          3          0     00300380    0.0  rtus_ufps0-13
  0  4512   3          3          0     00300380    0.0  rtus_ufps0-14
  0  4513   490        1955       0     00300380    0.0  rtuo0-15
  0  4514   490        1955       0     00300380    0.0  rtuo0-16
  0  4515   490        1955       0     00300380    0.0  rtuo_ufpp0-17
  0  4516   490        1955       0     00300380    0.0  rtuo_ufpp0-18
  0  4517   490        1955       0     00300380    0.0  rtuo_ufps0-19
  0  4518   490        1955       0     00300380    0.0  rtuo_ufps0-20
  0  4519   490        1955       0     00300380    0.0  rtuo_ufpp_ufps0-21
  0  4520   490        1955       0     00300380    0.0  rtuo_ufpp_ufps0-22
  1  0      0          2941       0     00004082    0.0  rtk1/1
  1  0      0          2941       0     00004082    0.0  rtk2/1
  1  0      0          2941       0     00104082    0.0  rtk3/1
  1  0      0          2941       0     00104082    0.0  rtk4/1
  1  0      0          2941       0     00104082    0.0  rtk5/1
  1  0      0          2940       0     00104082    0.0  rtk6/1
  1  4522   2          2940       0     00304182    0.0  rtup1-7
  1  4523   2          2940       0     00304182    0.0  rtup1-8
  1  4524   2          2940       0     00304182    0.0  rtup_ufpp1-9
  1  4525   2          2940       0     00304182    0.0  rtup_ufpp1-10
  1  4526   3          3          0     00300380    0.0  rtus1-11
  1  4527   3          3          0     00300380    0.0  rtus1-12
  1  4528   3          3          0     00300380    0.0  rtus_ufps1-13
  1  4529   3          3          0     00300380    0.0  rtus_ufps1-14
  1  4530   492        1963       0     00300380    0.0  rtuo1-15
  1  4531   492        1963       0     00300380    0.0  rtuo1-16
  1  4532   492        1963       0     00300380    0.0  rtuo_ufpp1-17
  1  4533   492        1963       0     00300380    0.0  rtuo_ufpp1-18
  1  4534   491        1962       0     00304182    0.0  rtuo_ufps1-19
  1  4535   491        1962       0     00304182    0.0  rtuo_ufps1-20
  1  4536   491        1962       0     00304182    0.0  rtuo_ufpp_ufps1-21
  1  4537   491        1962       0     00304182    0.0  rtuo_ufpp_ufps1-22
  1  0      0          1228306    0     00000000    0.1  IRQ27: [timer]

So I think it can't be all bad.

However I keep getting illegal instruction on most of the other testsuite
programs.  I must admit I have NOT recompiled the xenomai runtime and
libraries after upgrading the kernel from 3.8 to 3.12, since the xenomai
version is the same and I figured it wouldn't matter (I was going to
try that soon though, just in case).

For example:

root@omap5:~# strace /usr/lib/xenomai/testsuite/mutex-torture-native 
....
futex(0xb6fb719c, FUTEX_WAKE_PRIVATE, 2147483647) = 0
open("/dev/rtheap", O_RDWR)             = 3
ioctl(3, 0, 0xeef15010)                 = 0
mmap2(NULL, 12288, PROT_READ|PROT_WRITE, MAP_SHARED, 3, 0xf56bb) = 0xb6fc7000
close(3)                                = 0
futex(0xb6fb7248, FUTEX_WAKE_PRIVATE, 2147483647) = 0
open("/dev/rtheap", O_RDWR)             = 3
ioctl(3, 0, 0xbf155180)                 = 0
mmap2(NULL, 12288, PROT_READ|PROT_WRITE, MAP_SHARED, 3, 0xf54ef) = 0xb6e0a000
close(3)                                = 0
futex(0xb6fb724c, FUTEX_WAKE_PRIVATE, 2147483647) = 0
futex(0xb6fb71a8, FUTEX_WAKE_PRIVATE, 2147483647) = 0
futex(0xb6fb7320, FUTEX_WAKE_PRIVATE, 2147483647) = 0
mlockall(MCL_CURRENT|MCL_FUTURE)        = 0
rt_sigaction(SIGXCPU, {0x9069, [], SA_SIGINFO|0x4000000}, NULL, 8) = 0
rt_sigprocmask(SIG_BLOCK, [WINCH], [], 8) = 0
rt_sigaction(SIGWINCH, {0xb6fad6d1, [], SA_RESTART|SA_SIGINFO|0x4000000}, {SIG_DFL, [], 0}, 8) = 0
rt_sigprocmask(SIG_SETMASK, [], NULL, 8) = 0
futex(0xb6fb72e4, FUTEX_WAKE_PRIVATE, 2147483647) = 0
write(2, "simple_wait\n", 12)           = ? ERESTARTSYS (To be restarted)
--- SIGWINCH (Window changed) @ 0 (0) ---
sched_setscheduler(4540, SCHED_FIFO, { 2 }) = 0
rt_sigreturn(0x1)                       = 2
write(2, "simple_wait\n", 12simple_wait
)           = 12
sched_get_priority_min(SCHED_FIFO)      = 1
sched_get_priority_max(SCHED_FIFO)      = 99
mmap2(NULL, 32768, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0xb6e02000
mprotect(0xb6e02000, 4096, PROT_NONE)   = 0
sched_get_priority_min(SCHED_FIFO)      = 1
sched_get_priority_max(SCHED_FIFO)      = 99
clone(child_stack=0xb6e08fa8, flags=CLONE_VM|CLONE_FS|CLONE_FILES|CLONE_SIGHAND|CLONE_THREAD|CLONE_SYSVSEM|CLONE_SETTLS|CLONE_PARENT_SETTID|CLONE_CHILD_CLEARTID, parent_tidptr=0xb6e094d8, tls=0xb6e09930, child_tidptr=0xb6e094d8) = 4541
sched_setscheduler(4541, SCHED_FIFO, { 2 }) = 0
futex(0xb6e09684, FUTEX_WAKE_PRIVATE, 1) = 1
+++ killed by SIGILL +++
Illegal instruction

I am going to have to try it with gdb, and hopefully that will give me
a clue.

Does anyone have any hints on how to track this down, or even for how
to properly test that moving to 3.12 is actually working.

I will send some patches when I get this working.

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 17:45 [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel Lennart Sorensen
@ 2014-03-31 18:12 ` Gilles Chanteperdrix
  2014-03-31 18:24   ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-03-31 18:12 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 03/31/2014 07:45 PM, Lennart Sorensen wrote:
> Does anyone have any hints on how to track this down, or even for how
> to properly test that moving to 3.12 is actually working.

On what platform do you get this? If on cortex A8, and the user-space is 
compiled in thumb2 mode, note that an erratum workaround is needed, 
flushing the BTB at each context switch to avoid problem when ARM code 
is replaced by THUMB code at the same (virtual) address when switching 
context.

My advice would be to wait, Philippe is currently merging the I-pipe git 
with 3.14 (you can actually find the 3.12 merge in my git tree, under 
the branch raw/for-ipipe-3.12.0, it has been lightly tested though, as I 
wait for 3.14 to be ready to test more thoroughly).

If you can not wait, then you can enable CONFIG_DEBUG_USER, and pass 
user_debug=29 on the kernel command line, to have a complete a dump upon 
fault (and notably in the case of SIGILL). You can also extend this dump 
by using a hack done in the FCSE patch to print the equivalent of a dump 
of /proc/self/maps with markers indicating where the PC, SP, and fault 
address are when a fault occurs.

-- 
					    Gilles.

^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 18:12 ` Gilles Chanteperdrix
@ 2014-03-31 18:24   ` Lennart Sorensen
  2014-03-31 19:15     ` Lennart Sorensen
  2014-03-31 19:19     ` Gilles Chanteperdrix
  0 siblings, 2 replies; 45+ messages in thread
From: Lennart Sorensen @ 2014-03-31 18:24 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Mon, Mar 31, 2014 at 08:12:37PM +0200, Gilles Chanteperdrix wrote:
> On what platform do you get this? If on cortex A8, and the
> user-space is compiled in thumb2 mode, note that an erratum
> workaround is needed, flushing the BTB at each context switch to
> avoid problem when ARM code is replaced by THUMB code at the same
> (virtual) address when switching context.

Cortex-A15 (Omap5 system).  User space is thumb2 (Debian Wheezy armhf
based).

> My advice would be to wait, Philippe is currently merging the I-pipe
> git with 3.14 (you can actually find the 3.12 merge in my git tree,
> under the branch raw/for-ipipe-3.12.0, it has been lightly tested
> though, as I wait for 3.14 to be ready to test more thoroughly).

Unfortunately the drivers are not fully merged upstream yet, so I am
using the 3.12 branch from ti's git tree.  I was able to boot 3.14 but
without ethernet and usb and a few other things.

Comparing the ipipe changes for 3.14 would be useful though.

I only saw 3.11 raw in the tree when I was doing that part on thursday.
Is this new?  Or did I look in the wrong git tree?  No, I did a pull,
and it is there now.  I guess I was a day or two early. :)

> If you can not wait, then you can enable CONFIG_DEBUG_USER, and pass
> user_debug=29 on the kernel command line, to have a complete a dump
> upon fault (and notably in the case of SIGILL). You can also extend
> this dump by using a hack done in the FCSE patch to print the
> equivalent of a dump of /proc/self/maps with markers indicating
> where the PC, SP, and fault address are when a fault occurs.

That sounds worth trying.

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 18:24   ` Lennart Sorensen
@ 2014-03-31 19:15     ` Lennart Sorensen
  2014-03-31 19:17       ` Gilles Chanteperdrix
  2014-03-31 19:19     ` Gilles Chanteperdrix
  1 sibling, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-03-31 19:15 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Mon, Mar 31, 2014 at 02:24:04PM -0400, Lennart Sorensen wrote:
> I only saw 3.11 raw in the tree when I was doing that part on thursday.
> Is this new?  Or did I look in the wrong git tree?  No, I did a pull,
> and it is there now.  I guess I was a day or two early. :)

I looked at the 3.12 branch, and it is obviously not done given it has
merge problems still to be fixed, and at least one incorrect merge.
It does seem to address one of the powerpc areas I wasn't sure how
to handle.

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 19:15     ` Lennart Sorensen
@ 2014-03-31 19:17       ` Gilles Chanteperdrix
  2014-03-31 19:18         ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-03-31 19:17 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 03/31/2014 09:15 PM, Lennart Sorensen wrote:
> On Mon, Mar 31, 2014 at 02:24:04PM -0400, Lennart Sorensen wrote:
>> I only saw 3.11 raw in the tree when I was doing that part on thursday.
>> Is this new?  Or did I look in the wrong git tree?  No, I did a pull,
>> and it is there now.  I guess I was a day or two early. :)
> 
> I looked at the 3.12 branch, and it is obviously not done given it has
> merge problems still to be fixed, and at least one incorrect merge.
> It does seem to address one of the powerpc areas I wasn't sure how
> to handle.
> 
Are you sure you are loking at the right tree? I am talking about the
raw/for-ipipe-3.12.0 tree in ipipe-gch.git, not the raw/ipipe-3.12.0
tree in ipipe.git

-- 
                                                                Gilles.


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 19:17       ` Gilles Chanteperdrix
@ 2014-03-31 19:18         ` Lennart Sorensen
  2014-03-31 19:37           ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-03-31 19:18 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Mon, Mar 31, 2014 at 09:17:16PM +0200, Gilles Chanteperdrix wrote:
> Are you sure you are loking at the right tree? I am talking about the
> raw/for-ipipe-3.12.0 tree in ipipe-gch.git, not the raw/ipipe-3.12.0
> tree in ipipe.git

Oh, then no, wrong tree.

Let me check the other one.

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 19:18         ` Lennart Sorensen
@ 2014-03-31 19:37           ` Lennart Sorensen
  2014-03-31 19:44             ` Gilles Chanteperdrix
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-03-31 19:37 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Mon, Mar 31, 2014 at 03:18:49PM -0400, Lennart Sorensen wrote:
> On Mon, Mar 31, 2014 at 09:17:16PM +0200, Gilles Chanteperdrix wrote:
> > Are you sure you are loking at the right tree? I am talking about the
> > raw/for-ipipe-3.12.0 tree in ipipe-gch.git, not the raw/ipipe-3.12.0
> > tree in ipipe.git
> 
> Oh, then no, wrong tree.
> 
> Let me check the other one.

Ok that looks better.

Couple of things:

I think this is wrong:

  @@ -268,13 +298,22 @@ extern void flush_cache_page(struct vm_area_struct *vma, unsigned long user_addr                               
    * Harvard caches are synchronised for the user space address range.                                                                
    * This is used for the ARM private sys_cacheflush system call.
    */
  -#define flush_cache_user_range(s,e)    __cpuc_coherent_user_range(s,e)
  +#define flush_cache_user_range(s, e)                                   \                                                            
  +       ({                                                              \                                                            
  +               struct mm_struct *_mm = current->mm;                    \
  +               unsigned long _s, _e;                                   \
  +               _s = fcse_va_to_mva(_mm, s) & PAGE_MASK;                \
  +               _e = PAGE_ALIGN(fcse_va_to_mva(_mm, e));                \
  +               __cpuc_coherent_user_range(_s, _e);                     \                                                            
  +       })                                                                                                                           
   
   /* 
    * Perform necessary cache operations to ensure that data previously                                                                

The kernel specificly did NOT want the PAGE_MASK and PAGE_ALIGN and got
rid of it.  At last that's what the commit that changed it said.  So I
think the ipipe patch should follow that change too.  ie:

  @@ -268,13 +298,22 @@ extern void flush_cache_page(struct vm_area_struct *vma, unsigned long user_addr                               
    * Harvard caches are synchronised for the user space address range.                                                                
    * This is used for the ARM private sys_cacheflush system call.
    */
  -#define flush_cache_user_range(s,e)    __cpuc_coherent_user_range(s,e)
  +#define flush_cache_user_range(s, e)                                   \                                                            
  +       ({                                                              \                                                            
  +               struct mm_struct *_mm = current->mm;                    \
  +               unsigned long _s, _e;                                   \
  +               _s = fcse_va_to_mva(_mm, s);                            \
  +               _e = fcse_va_to_mva(_mm, e);                            \
  +               __cpuc_coherent_user_range(_s, _e);                     \                                                            
  +       })                                                                                                                           
   
   /* 
    * Perform necessary cache operations to ensure that data previously                                                                

Also my version of arch/arm/include/asm/barrier.h turned out a bit
different (I was trying to avoid changing the kernel code as much as
possible).  Diff versus yours is:

--- /tmp/barrier.h      2014-03-31 19:26:10.000000000 +0000
+++ linux-3.12.14.rr1/arch/arm/include/asm/barrier.h    2014-03-27 20:06:33.000000000 +0000
@@ -16,17 +16,15 @@
 #if __LINUX_ARM_ARCH__ >= 7
 #define isb(option) __asm__ __volatile__ ("isb " #option : : : "memory")
 #define dsb(option) __asm__ __volatile__ ("dsb " #option : : : "memory")
-#define DMB(option) "dmb " #option
+#define DMB "dmb"
 #define DMB_IN
-
 #elif defined(CONFIG_CPU_XSC3) || __LINUX_ARM_ARCH__ == 6
 #define isb(x) __asm__ __volatile__ ("mcr p15, 0, %0, c7, c5, 4" \
                                    : : "r" (0) : "memory")
 #define dsb(x) __asm__ __volatile__ ("mcr p15, 0, %0, c7, c10, 4" \
                                    : : "r" (0) : "memory")
-#define DMB(option) "mcr p15, 0, %0, c7, c10, 5"
+#define DMB "mcr p15, 0, %0, c7, c10, 5"
 #define DMB_IN "r" (0)
-
 #elif defined(CONFIG_CPU_FA526)
 #define isb(x) __asm__ __volatile__ ("mcr p15, 0, %0, c7, c5, 4" \
                                    : : "r" (0) : "memory")
@@ -39,9 +37,9 @@
 #endif
 
 #ifdef DMB
-#define dmb(option) __asm__ __volatile__(DMB(option) : : DMB_IN : "memory")
+#define dmb(option) __asm__ __volatile__(DMB #option : : DMB_IN : "memory")
 #else
-#define dmb(option) __asm__ __volatile__("" : : : "memory")
+#define dmb(option) __asm__ __volatile__("" #option : : : "memory")
 #endif
 
 
@@ -62,7 +60,6 @@
 #define smp_rmb()      barrier()
 #define smp_wmb()      barrier()
 #else
-
 #ifdef CONFIG_THUMB2_KERNEL
 #define SMP_ONLY(smp) \
        "9998:  " smp "\n"                                      \
@@ -80,16 +77,13 @@
 #endif
 
 #ifdef DMB
-#define smp_mb() \
-       __asm__ __volatile__ (SMP_ONLY(DMB(ish)) : : DMB_IN : "memory")
-#define smp_rmb() \
-       __asm__ __volatile__ (SMP_ONLY(DMB(ish)) : : DMB_IN : "memory")
-#define smp_wmb() \
-       __asm__ __volatile__ (SMP_ONLY(DMB(ishst)) : : DMB_IN : "memory")
-#else
-#define smp_mb() barrier()
-#define smp_rmb() barrier()
-#define smp_wmb() barrier()
+#define smp_mb() __asm__ __volatile__ (SMP_ONLY(DMB " ish") : : DMB_IN : "memory")
+#define smp_rmb()      smp_mb()
+#define smp_wmb() __asm__ __volatile__ (SMP_ONLY(DMB " ishst") : : DMB_IN : "memory")
+#else
+#define smp_mb()       dmb(ish)
+#define smp_rmb()      smp_mb()
+#define smp_wmb()      dmb(ishst)
 #endif
 #endif

I haven't fully checked if there is any functional difference yet.

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 19:37           ` Lennart Sorensen
@ 2014-03-31 19:44             ` Gilles Chanteperdrix
  2014-03-31 20:42               ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-03-31 19:44 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 03/31/2014 09:37 PM, Lennart Sorensen wrote:
> On Mon, Mar 31, 2014 at 03:18:49PM -0400, Lennart Sorensen wrote:
>> On Mon, Mar 31, 2014 at 09:17:16PM +0200, Gilles Chanteperdrix wrote:
>>> Are you sure you are loking at the right tree? I am talking about the
>>> raw/for-ipipe-3.12.0 tree in ipipe-gch.git, not the raw/ipipe-3.12.0
>>> tree in ipipe.git
>>
>> Oh, then no, wrong tree.
>>
>> Let me check the other one.
> 
> Ok that looks better.
> 
> Couple of things:
> 
> I think this is wrong:
> 
>   @@ -268,13 +298,22 @@ extern void flush_cache_page(struct vm_area_struct *vma, unsigned long user_addr                               
>     * Harvard caches are synchronised for the user space address range.                                                                
>     * This is used for the ARM private sys_cacheflush system call.
>     */
>   -#define flush_cache_user_range(s,e)    __cpuc_coherent_user_range(s,e)
>   +#define flush_cache_user_range(s, e)                                   \                                                            
>   +       ({                                                              \                                                            
>   +               struct mm_struct *_mm = current->mm;                    \
>   +               unsigned long _s, _e;                                   \
>   +               _s = fcse_va_to_mva(_mm, s) & PAGE_MASK;                \
>   +               _e = PAGE_ALIGN(fcse_va_to_mva(_mm, e));                \
>   +               __cpuc_coherent_user_range(_s, _e);                     \                                                            
>   +       })                                                                                                                           
>    
>    /* 
>     * Perform necessary cache operations to ensure that data previously                                                                
> 
> The kernel specificly did NOT want the PAGE_MASK and PAGE_ALIGN and got
> rid of it.  At last that's what the commit that changed it said.  So I
> think the ipipe patch should follow that change too.  ie:
> 
>   @@ -268,13 +298,22 @@ extern void flush_cache_page(struct vm_area_struct *vma, unsigned long user_addr                               
>     * Harvard caches are synchronised for the user space address range.                                                                
>     * This is used for the ARM private sys_cacheflush system call.
>     */
>   -#define flush_cache_user_range(s,e)    __cpuc_coherent_user_range(s,e)
>   +#define flush_cache_user_range(s, e)                                   \                                                            
>   +       ({                                                              \                                                            
>   +               struct mm_struct *_mm = current->mm;                    \
>   +               unsigned long _s, _e;                                   \
>   +               _s = fcse_va_to_mva(_mm, s);                            \
>   +               _e = fcse_va_to_mva(_mm, e);                            \
>   +               __cpuc_coherent_user_range(_s, _e);                     \                                                            
>   +       })                                                                                                                           
>    
>    /* 
>     * Perform necessary cache operations to ensure that data previously                                                                

Ok, thanks, will fix in 3.14 patch.

> 
> Also my version of arch/arm/include/asm/barrier.h turned out a bit
> different (I was trying to avoid changing the kernel code as much as
> possible).  Diff versus yours is:

I do not really see differences...



> +#define dmb(option) __asm__ __volatile__("" #option : : : "memory")

...except this which is wrong (ish, shst are probably not valid
instructions, and only make sense as suffixes after dmb). It should not
even compile.



-- 
                                                                Gilles.


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 19:44             ` Gilles Chanteperdrix
@ 2014-03-31 20:42               ` Lennart Sorensen
  2014-03-31 20:53                 ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-03-31 20:42 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Mon, Mar 31, 2014 at 09:44:44PM +0200, Gilles Chanteperdrix wrote:
> Ok, thanks, will fix in 3.14 patch.
> 
> > 
> > Also my version of arch/arm/include/asm/barrier.h turned out a bit
> > different (I was trying to avoid changing the kernel code as much as
> > possible).  Diff versus yours is:
> 
> I do not really see differences...
> 
> 
> 
> > +#define dmb(option) __asm__ __volatile__("" #option : : : "memory")
> 
> ...except this which is wrong (ish, shst are probably not valid
> instructions, and only make sense as suffixes after dmb). It should not
> even compile.

Hmm, I guess that case never is hit in my config.  I am running SMP.
I am willing to agree mine is probably wrong then.

So comparing the diff I have against yours so far they are amazingly
close to identical.  I found the arch_timer_arm.c changes were nicer in
your version so I am putting that in now, and the powerpc/kernel/irq.c
you dealt with (I had no idea what was going on there), so i am grabbing
that too.

I found a change in your version of kernel/context_tracking.c that I am
going to grab.  Seems to be mostly an ordering difference, but checking
ipipe stuff first makes sense.

I found I had missaplied a bit in kernel/sched/core.c, which explains
why I thought it looked odd while applying it.

I moved to your version of barrier.h for arm.  Everything else seems
like just whitespace differences, so I will give this a try.

-- 
Len Sorensen

^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 20:42               ` Lennart Sorensen
@ 2014-03-31 20:53                 ` Lennart Sorensen
  2014-03-31 20:57                   ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-03-31 20:53 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Mon, Mar 31, 2014 at 04:42:57PM -0400, Lennart Sorensen wrote:
> Hmm, I guess that case never is hit in my config.  I am running SMP.
> I am willing to agree mine is probably wrong then.
> 
> So comparing the diff I have against yours so far they are amazingly
> close to identical.  I found the arch_timer_arm.c changes were nicer in
> your version so I am putting that in now, and the powerpc/kernel/irq.c
> you dealt with (I had no idea what was going on there), so i am grabbing
> that too.
> 
> I found a change in your version of kernel/context_tracking.c that I am
> going to grab.  Seems to be mostly an ordering difference, but checking
> ipipe stuff first makes sense.
> 
> I found I had missaplied a bit in kernel/sched/core.c, which explains
> why I thought it looked odd while applying it.
> 
> I moved to your version of barrier.h for arm.  Everything else seems
> like just whitespace differences, so I will give this a try.

Any idea what this means at boot by the way?

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.12-1-dra7xx (debian-kernel@lists.debian.org) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP PREEMPT Debian 3.12.14-0.1 (2014-03-24)
[    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] Machine: Generic DRA7XX (Flattened Device Tree), model: TI DRA7
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] On node 0 totalpages: 388864
[    0.000000] free_area_init_node: node 0, pgdat c07ef800, node_mem_map c0d8b000
[    0.000000]   Normal zone: 1520 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 194560 pages, LIFO batch:31
[    0.000000]   HighMem zone: 1520 pages used for memmap
[    0.000000]   HighMem zone: 194304 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 12 pages/cpu @c19a4000 s25216 r8192 d15744 u49152
[    0.000000] pcpu-alloc: s25216 r8192 d15744 u49152 alloc=12*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 387344
[    0.000000] Kernel command line: elevator=noop console=ttyO0,115200n8 root=/dev/mmcblk0p2 rw rootwait earlyprintk fixrtc
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 1528216K/1555456K available (5138K kernel code, 545K rwdata, 2036K rodata, 392K init, 5714K bss, 27240K reserved, 777216K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0709f54   (7176 kB)
[    0.000000]       .init : 0xc070a000 - 0xc076c280   ( 393 kB)
[    0.000000]       .data : 0xc076e000 - 0xc07f653c   ( 546 kB)
[    0.000000]        .bss : 0xc07f653c - 0xc0d8ae00   (5715 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] OMAP clockevent source: timer1 at 32768 Hz
[    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
[    0.000000] OMAP clocksource: 32k_counter at 32768 Hz
[    0.000000] Architected cp15 timer(s) running at 6.14MHz (virt).
[    0.000000] I-pipe, 6.144 MHz clocksource
[    0.000000] Switching to timer-based delay loop
[    0.000000] sched_clock: ARM arch timer >56 bits at 6144kHz, resolution 162ns
[    0.000000] Interrupt pipeline (release #1)
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[    0.000000] ... MAX_LOCKDEP_SUBCLASSES:  8
[    0.000000] ... MAX_LOCK_DEPTH:          48
[    0.000000] ... MAX_LOCKDEP_KEYS:        8191
[    0.000000] ... CLASSHASH_SIZE:          4096
[    0.000000] ... MAX_LOCKDEP_ENTRIES:     16384
[    0.000000] ... MAX_LOCKDEP_CHAINS:      32768
[    0.000000] ... CHAINHASH_SIZE:          16384
[    0.000000]  memory used by lock dependency info: 3695 kB
[    0.000000]  per task-struct memory footprint: 1152 bytes
[341548.562288] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.28 BogoMIPS (lpj=6144)
[341548.562303] pid_max: default: 32768 minimum: 301
[341548.562633] Security Framework initialized
[341548.562744] Mount-cache hash table entries: 512
[341548.639638] CPU: Testing write buffer coherency: ok
[341548.640576] /cpus/cpu@0 missing clock-frequency property
[341548.640606] /cpus/cpu@1 missing clock-frequency property
[341548.640619] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[341548.640646] Setting up static identity map for 0xc04dec28 - 0xc04dec80
[341548.649022] CPU1: Booted secondary processor
[341548.649061] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[341548.649433] Brought up 2 CPUs
[341548.649448] SMP: Total of 2 processors activated.
[341548.649456] CPU: All CPU(s) started in SVC mode.
[341548.649920] 
[341548.649928] =================================
[341548.649934] [ INFO: inconsistent lock state ]
[341548.649943] 3.12-1-dra7xx #1 Not tainted
[341548.649950] ---------------------------------
[341548.649957] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
[341548.649966] swapper/0/0 [HC0[0]:SC0[0]:HE1:SE1] takes:
[341548.649973]  (std_spinlock_raw(&rq->lock)){?.....}, at: [<c04d7720>] __schedule+0x554/0x80c
[341548.650004] {IN-HARDIRQ-W} state was registered at:
[341548.650011]   [<c009801c>] __lock_acquire+0xac4/0x1bb0
[341548.650031]   [<c0099678>] lock_acquire+0x94/0x13c
[341548.650044]   [<c04d8c68>] _raw_spin_lock+0x38/0x48
[341548.650056]   [<c006b9f4>] scheduler_tick+0x2c/0xb4
[341548.650071]   [<c004b3a4>] update_process_times+0x5c/0x68
[341548.650087]   [<c0090d60>] tick_periodic+0x38/0xb4
[341548.650099]   [<c0090eec>] tick_handle_periodic+0x18/0x7c
[341548.650110]   [<c04021e8>] arch_timer_handler_virt+0x64/0x80
[341548.650124]   [<c0085128>] handle_percpu_devid_irq+0x84/0x1e0
[341548.650135]   [<c0082114>] generic_handle_irq+0x20/0x30
[341548.650149]   [<c000f5bc>] handle_IRQ+0x5c/0xd0
[341548.650162]   [<c00ae050>] __ipipe_do_sync_stage+0x2e4/0x300
[341548.650174]   [<c0008678>] __ipipe_grab_irq+0x48/0x8c
[341548.650185]   [<c0008930>] gic_handle_irq+0x28/0x5c
[341548.650196]   [<c04d9a84>] __irq_svc+0x44/0x70
[341548.650208]   [<c00ae260>] ipipe_unstall_root+0x44/0x5c
[341548.650220]   [<c070a99c>] start_kernel+0x1f8/0x31c
[341548.650234]   [<80008074>] 0x80008074
[341548.650246] irq event stamp: 29031
[341548.650253] hardirqs last  enabled at (29030): [<c04d942c>] _raw_spin_unlock_irq+0x24/0x50
[341548.650265] hardirqs last disabled at (29031): [<c04d8d30>] _raw_spin_lock_irqsave+0x1c/0x60
[341548.650277] softirqs last  enabled at (29021): [<c0043318>] irq_enter+0x6c/0x70
[341548.650290] softirqs last disabled at (29020): [<c004330c>] irq_enter+0x60/0x70
[341548.650302] 
[341548.650302] other info that might help us debug this:
[341548.650309]  Possible unsafe locking scenario:
[341548.650309] 
[341548.650317]        CPU0
[341548.650323]        ----
[341548.650328]   lock(std_spinlock_raw(&rq->lock));
[341548.650341]   <Interrupt>
[341548.650346]     lock(std_spinlock_raw(&rq->lock));
[341548.650359] 
[341548.650359]  *** DEADLOCK ***
[341548.650359] 
[341548.650369] 1 lock held by swapper/0/0:
[341548.650375]  #0:  (std_spinlock_raw(&rq->lock)){?.....}, at: [<c04d7720>] __schedule+0x554/0x80c
[341548.650402] 
[341548.650402] stack backtrace:
[341548.650414] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.12-1-dra7xx #1 Debian 3.12.14-0.1
[341548.650434] [<c001610c>] (unwind_backtrace+0x0/0xf8) from [<c00126b4>] (show_stack+0x10/0x14)
[341548.650451] [<c00126b4>] (show_stack+0x10/0x14) from [<c04d3428>] (dump_stack+0x6c/0xac)
[341548.650466] [<c04d3428>] (dump_stack+0x6c/0xac) from [<c04d07b4>] (print_usage_bug+0x258/0x2c8)
[341548.650481] [<c04d07b4>] (print_usage_bug+0x258/0x2c8) from [<c0097120>] (mark_lock+0x290/0x6c8)
[341548.650496] [<c0097120>] (mark_lock+0x290/0x6c8) from [<c0099ee4>] (mark_held_locks+0x60/0x138)
[341548.650511] [<c0099ee4>] (mark_held_locks+0x60/0x138) from [<c009a02c>] (trace_hardirqs_on_caller+0x70/0x1c4)
[341548.650525] [<c009a02c>] (trace_hardirqs_on_caller+0x70/0x1c4) from [<c04d9ab4>] (__ipipe_fast_svc_irq_exit+0x4/0x14)
[341548.650538] [<c04d9ab4>] (__ipipe_fast_svc_irq_exit+0x4/0x14) from [<c0073f44>] (idle_enter_fair+0x0/0x1a4)
[341548.650554] [<c0073f44>] (idle_enter_fair+0x0/0x1a4) from [<c076b2c0>] (runqueues+0x0/0x5c0)
[341548.659443] devtmpfs: initialized

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 20:53                 ` Lennart Sorensen
@ 2014-03-31 20:57                   ` Lennart Sorensen
  2014-03-31 21:06                     ` Gilles Chanteperdrix
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-03-31 20:57 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Mon, Mar 31, 2014 at 04:53:39PM -0400, Lennart Sorensen wrote:
> On Mon, Mar 31, 2014 at 04:42:57PM -0400, Lennart Sorensen wrote:
> > Hmm, I guess that case never is hit in my config.  I am running SMP.
> > I am willing to agree mine is probably wrong then.
> > 
> > So comparing the diff I have against yours so far they are amazingly
> > close to identical.  I found the arch_timer_arm.c changes were nicer in
> > your version so I am putting that in now, and the powerpc/kernel/irq.c
> > you dealt with (I had no idea what was going on there), so i am grabbing
> > that too.
> > 
> > I found a change in your version of kernel/context_tracking.c that I am
> > going to grab.  Seems to be mostly an ordering difference, but checking
> > ipipe stuff first makes sense.
> > 
> > I found I had missaplied a bit in kernel/sched/core.c, which explains
> > why I thought it looked odd while applying it.
> > 
> > I moved to your version of barrier.h for arm.  Everything else seems
> > like just whitespace differences, so I will give this a try.
> 
> Any idea what this means at boot by the way?
> 
> [    0.000000] Booting Linux on physical CPU 0x0
> [    0.000000] Linux version 3.12-1-dra7xx (debian-kernel@lists.debian.org) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP PREEMPT Debian 3.12.14-0.1 (2014-03-24)
> [    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=10c5387d
> [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
> [    0.000000] Machine: Generic DRA7XX (Flattened Device Tree), model: TI DRA7
> [    0.000000] Memory policy: ECC disabled, Data cache writealloc
> [    0.000000] On node 0 totalpages: 388864
> [    0.000000] free_area_init_node: node 0, pgdat c07ef800, node_mem_map c0d8b000
> [    0.000000]   Normal zone: 1520 pages used for memmap
> [    0.000000]   Normal zone: 0 pages reserved
> [    0.000000]   Normal zone: 194560 pages, LIFO batch:31
> [    0.000000]   HighMem zone: 1520 pages used for memmap
> [    0.000000]   HighMem zone: 194304 pages, LIFO batch:31
> [    0.000000] PERCPU: Embedded 12 pages/cpu @c19a4000 s25216 r8192 d15744 u49152
> [    0.000000] pcpu-alloc: s25216 r8192 d15744 u49152 alloc=12*4096
> [    0.000000] pcpu-alloc: [0] 0 [0] 1 
> [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 387344
> [    0.000000] Kernel command line: elevator=noop console=ttyO0,115200n8 root=/dev/mmcblk0p2 rw rootwait earlyprintk fixrtc
> [    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
> [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> [    0.000000] Memory: 1528216K/1555456K available (5138K kernel code, 545K rwdata, 2036K rodata, 392K init, 5714K bss, 27240K reserved, 777216K highmem)
> [    0.000000] Virtual kernel memory layout:
> [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
> [    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
> [    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
> [    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
> [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
> [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
> [    0.000000]       .text : 0xc0008000 - 0xc0709f54   (7176 kB)
> [    0.000000]       .init : 0xc070a000 - 0xc076c280   ( 393 kB)
> [    0.000000]       .data : 0xc076e000 - 0xc07f653c   ( 546 kB)
> [    0.000000]        .bss : 0xc07f653c - 0xc0d8ae00   (5715 kB)
> [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
> [    0.000000] Preemptible hierarchical RCU implementation.
> [    0.000000] NR_IRQS:16 nr_irqs:16 16
> [    0.000000] OMAP clockevent source: timer1 at 32768 Hz
> [    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
> [    0.000000] OMAP clocksource: 32k_counter at 32768 Hz
> [    0.000000] Architected cp15 timer(s) running at 6.14MHz (virt).
> [    0.000000] I-pipe, 6.144 MHz clocksource
> [    0.000000] Switching to timer-based delay loop
> [    0.000000] sched_clock: ARM arch timer >56 bits at 6144kHz, resolution 162ns
> [    0.000000] Interrupt pipeline (release #1)
> [    0.000000] Console: colour dummy device 80x30
> [    0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
> [    0.000000] ... MAX_LOCKDEP_SUBCLASSES:  8
> [    0.000000] ... MAX_LOCK_DEPTH:          48
> [    0.000000] ... MAX_LOCKDEP_KEYS:        8191
> [    0.000000] ... CLASSHASH_SIZE:          4096
> [    0.000000] ... MAX_LOCKDEP_ENTRIES:     16384
> [    0.000000] ... MAX_LOCKDEP_CHAINS:      32768
> [    0.000000] ... CHAINHASH_SIZE:          16384
> [    0.000000]  memory used by lock dependency info: 3695 kB
> [    0.000000]  per task-struct memory footprint: 1152 bytes
> [341548.562288] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.28 BogoMIPS (lpj=6144)
> [341548.562303] pid_max: default: 32768 minimum: 301
> [341548.562633] Security Framework initialized
> [341548.562744] Mount-cache hash table entries: 512
> [341548.639638] CPU: Testing write buffer coherency: ok
> [341548.640576] /cpus/cpu@0 missing clock-frequency property
> [341548.640606] /cpus/cpu@1 missing clock-frequency property
> [341548.640619] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
> [341548.640646] Setting up static identity map for 0xc04dec28 - 0xc04dec80
> [341548.649022] CPU1: Booted secondary processor
> [341548.649061] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
> [341548.649433] Brought up 2 CPUs
> [341548.649448] SMP: Total of 2 processors activated.
> [341548.649456] CPU: All CPU(s) started in SVC mode.
> [341548.649920] 
> [341548.649928] =================================
> [341548.649934] [ INFO: inconsistent lock state ]
> [341548.649943] 3.12-1-dra7xx #1 Not tainted
> [341548.649950] ---------------------------------
> [341548.649957] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
> [341548.649966] swapper/0/0 [HC0[0]:SC0[0]:HE1:SE1] takes:
> [341548.649973]  (std_spinlock_raw(&rq->lock)){?.....}, at: [<c04d7720>] __schedule+0x554/0x80c
> [341548.650004] {IN-HARDIRQ-W} state was registered at:
> [341548.650011]   [<c009801c>] __lock_acquire+0xac4/0x1bb0
> [341548.650031]   [<c0099678>] lock_acquire+0x94/0x13c
> [341548.650044]   [<c04d8c68>] _raw_spin_lock+0x38/0x48
> [341548.650056]   [<c006b9f4>] scheduler_tick+0x2c/0xb4
> [341548.650071]   [<c004b3a4>] update_process_times+0x5c/0x68
> [341548.650087]   [<c0090d60>] tick_periodic+0x38/0xb4
> [341548.650099]   [<c0090eec>] tick_handle_periodic+0x18/0x7c
> [341548.650110]   [<c04021e8>] arch_timer_handler_virt+0x64/0x80
> [341548.650124]   [<c0085128>] handle_percpu_devid_irq+0x84/0x1e0
> [341548.650135]   [<c0082114>] generic_handle_irq+0x20/0x30
> [341548.650149]   [<c000f5bc>] handle_IRQ+0x5c/0xd0
> [341548.650162]   [<c00ae050>] __ipipe_do_sync_stage+0x2e4/0x300
> [341548.650174]   [<c0008678>] __ipipe_grab_irq+0x48/0x8c
> [341548.650185]   [<c0008930>] gic_handle_irq+0x28/0x5c
> [341548.650196]   [<c04d9a84>] __irq_svc+0x44/0x70
> [341548.650208]   [<c00ae260>] ipipe_unstall_root+0x44/0x5c
> [341548.650220]   [<c070a99c>] start_kernel+0x1f8/0x31c
> [341548.650234]   [<80008074>] 0x80008074
> [341548.650246] irq event stamp: 29031
> [341548.650253] hardirqs last  enabled at (29030): [<c04d942c>] _raw_spin_unlock_irq+0x24/0x50
> [341548.650265] hardirqs last disabled at (29031): [<c04d8d30>] _raw_spin_lock_irqsave+0x1c/0x60
> [341548.650277] softirqs last  enabled at (29021): [<c0043318>] irq_enter+0x6c/0x70
> [341548.650290] softirqs last disabled at (29020): [<c004330c>] irq_enter+0x60/0x70
> [341548.650302] 
> [341548.650302] other info that might help us debug this:
> [341548.650309]  Possible unsafe locking scenario:
> [341548.650309] 
> [341548.650317]        CPU0
> [341548.650323]        ----
> [341548.650328]   lock(std_spinlock_raw(&rq->lock));
> [341548.650341]   <Interrupt>
> [341548.650346]     lock(std_spinlock_raw(&rq->lock));
> [341548.650359] 
> [341548.650359]  *** DEADLOCK ***
> [341548.650359] 
> [341548.650369] 1 lock held by swapper/0/0:
> [341548.650375]  #0:  (std_spinlock_raw(&rq->lock)){?.....}, at: [<c04d7720>] __schedule+0x554/0x80c
> [341548.650402] 
> [341548.650402] stack backtrace:
> [341548.650414] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.12-1-dra7xx #1 Debian 3.12.14-0.1
> [341548.650434] [<c001610c>] (unwind_backtrace+0x0/0xf8) from [<c00126b4>] (show_stack+0x10/0x14)
> [341548.650451] [<c00126b4>] (show_stack+0x10/0x14) from [<c04d3428>] (dump_stack+0x6c/0xac)
> [341548.650466] [<c04d3428>] (dump_stack+0x6c/0xac) from [<c04d07b4>] (print_usage_bug+0x258/0x2c8)
> [341548.650481] [<c04d07b4>] (print_usage_bug+0x258/0x2c8) from [<c0097120>] (mark_lock+0x290/0x6c8)
> [341548.650496] [<c0097120>] (mark_lock+0x290/0x6c8) from [<c0099ee4>] (mark_held_locks+0x60/0x138)
> [341548.650511] [<c0099ee4>] (mark_held_locks+0x60/0x138) from [<c009a02c>] (trace_hardirqs_on_caller+0x70/0x1c4)
> [341548.650525] [<c009a02c>] (trace_hardirqs_on_caller+0x70/0x1c4) from [<c04d9ab4>] (__ipipe_fast_svc_irq_exit+0x4/0x14)
> [341548.650538] [<c04d9ab4>] (__ipipe_fast_svc_irq_exit+0x4/0x14) from [<c0073f44>] (idle_enter_fair+0x0/0x1a4)
> [341548.650554] [<c0073f44>] (idle_enter_fair+0x0/0x1a4) from [<c076b2c0>] (runqueues+0x0/0x5c0)
> [341548.659443] devtmpfs: initialized

No change in behaviour.  switchtest works, clocktest works, most other
things have illegal instruction.  Just waiting for the library and
runtime to recompile against 3.12's headers in case it matters.
After that it will be debug time.

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 20:57                   ` Lennart Sorensen
@ 2014-03-31 21:06                     ` Gilles Chanteperdrix
  2014-03-31 21:25                       ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-03-31 21:06 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 03/31/2014 10:57 PM, Lennart Sorensen wrote:
> On Mon, Mar 31, 2014 at 04:53:39PM -0400, Lennart Sorensen wrote:
>> [341548.649928] =================================
>> [341548.649934] [ INFO: inconsistent lock state ]
>> [341548.649943] 3.12-1-dra7xx #1 Not tainted
>> [341548.649950] ---------------------------------
>> [341548.649957] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.

This looks fishy. It means that the root domain is not stalled while
interrupt handler is called. This would need to be checked.

> No change in behaviour.  switchtest works, clocktest works, most other
> things have illegal instruction.  Just waiting for the library and
> runtime to recompile against 3.12's headers in case it matters.
> After that it will be debug time.
> 

Ok. You seem to have many debug options enabled. Please find attached
the config I have used during my tests on omap5.

-- 
                                                                Gilles.
-------------- next part --------------
#
# Automatically generated file; DO NOT EDIT.
# Linux/arm 3.8.4 Kernel Configuration
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_GENERIC_GPIO=y
CONFIG_HAVE_PROC_CPU=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_ARCH_HAS_CPUFREQ=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_NEED_DMA_MAP_STATE=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_ARM_PATCH_PHYS_VIRT=y
CONFIG_GENERIC_BUG=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_HAVE_IRQ_WORK=y
CONFIG_IRQ_WORK=y
CONFIG_BUILDTIME_EXTABLE_SORT=y

#
# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_CROSS_COMPILE=""
CONFIG_LOCALVERSION="vs"
CONFIG_LOCALVERSION_AUTO=y
CONFIG_HAVE_KERNEL_GZIP=y
CONFIG_HAVE_KERNEL_LZMA=y
CONFIG_HAVE_KERNEL_XZ=y
CONFIG_HAVE_KERNEL_LZO=y
# CONFIG_KERNEL_GZIP is not set
# CONFIG_KERNEL_LZMA is not set
CONFIG_KERNEL_XZ=y
# CONFIG_KERNEL_LZO is not set
CONFIG_DEFAULT_HOSTNAME="(none)"
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
CONFIG_POSIX_MQUEUE_SYSCTL=y
# CONFIG_FHANDLE is not set
# CONFIG_AUDIT is not set
CONFIG_HAVE_GENERIC_HARDIRQS=y

#
# IRQ subsystem
#
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_IRQ_SHOW=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_CHIP=y
CONFIG_IRQ_DOMAIN=y
# CONFIG_IRQ_DOMAIN_DEBUG is not set
CONFIG_SPARSE_IRQ=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_KTIME_SCALAR=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y

#
# Timers subsystem
#
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
# CONFIG_HIGH_RES_TIMERS is not set

#
# CPU/Task time and stats accounting
#
CONFIG_TICK_CPU_ACCOUNTING=y
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set

#
# RCU Subsystem
#
CONFIG_TREE_PREEMPT_RCU=y
CONFIG_PREEMPT_RCU=y
CONFIG_RCU_FANOUT=32
CONFIG_RCU_FANOUT_LEAF=16
# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_RCU_FAST_NO_HZ is not set
# CONFIG_TREE_RCU_TRACE is not set
# CONFIG_RCU_BOOST is not set
# CONFIG_RCU_NOCB_CPU is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=16
# CONFIG_CGROUPS is not set
# CONFIG_CHECKPOINT_RESTORE is not set
# CONFIG_NAMESPACES is not set
# CONFIG_SCHED_AUTOGROUP is not set
# CONFIG_SYSFS_DEPRECATED is not set
# CONFIG_RELAY is not set
# CONFIG_BLK_DEV_INITRD is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_ANON_INODES=y
CONFIG_EXPERT=y
CONFIG_HAVE_UID16=y
CONFIG_UID16=y
# CONFIG_SYSCTL_SYSCALL is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
CONFIG_EMBEDDED=y
CONFIG_HAVE_PERF_EVENTS=y
CONFIG_PERF_USE_VMALLOC=y

#
# Kernel Performance Events And Counters
#
# CONFIG_PERF_EVENTS is not set
CONFIG_VM_EVENT_COUNTERS=y
# CONFIG_SLUB_DEBUG is not set
CONFIG_COMPAT_BRK=y
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
CONFIG_TRACEPOINTS=y
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
# CONFIG_JUMP_LABEL is not set
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_DMA_ATTRS=y
CONFIG_HAVE_DMA_CONTIGUOUS=y
CONFIG_USE_GENERIC_SMP_HELPERS=y
CONFIG_GENERIC_SMP_IDLE_THREAD=y
CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
CONFIG_HAVE_ARCH_JUMP_LABEL=y
CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
CONFIG_MODULES_USE_ELF_REL=y
CONFIG_CLONE_BACKWARDS=y

#
# GCOV-based kernel profiling
#
# CONFIG_GCOV_KERNEL is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_RT_MUTEXES=y
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_FORCE_LOAD=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
# CONFIG_MODULE_SIG is not set
CONFIG_STOP_MACHINE=y
CONFIG_BLOCK=y
CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_BSGLIB is not set
# CONFIG_BLK_DEV_INTEGRITY is not set

#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
# CONFIG_MAC_PARTITION is not set
CONFIG_MSDOS_PARTITION=y
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
# CONFIG_LDM_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
CONFIG_EFI_PARTITION=y
# CONFIG_SYSV68_PARTITION is not set

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
CONFIG_UNINLINE_SPIN_UNLOCK=y
CONFIG_MUTEX_SPIN_ON_OWNER=y

#
# Real-time sub-system
#
CONFIG_XENOMAI=y
CONFIG_XENO_GENERIC_STACKPOOL=y
CONFIG_XENO_FASTSYNCH_DEP=y
CONFIG_XENO_FASTSYNCH=y
CONFIG_XENO_OPT_NUCLEUS=y
CONFIG_XENO_OPT_PERVASIVE=y
# CONFIG_XENO_OPT_PRIOCPL is not set
CONFIG_XENO_OPT_PIPELINE_HEAD=y
# CONFIG_XENO_OPT_SCHED_CLASSES is not set
CONFIG_XENO_OPT_PIPE=y
CONFIG_XENO_OPT_MAP=y
CONFIG_XENO_OPT_VFILE=y
CONFIG_XENO_OPT_PIPE_NRDEV=32
CONFIG_XENO_OPT_REGISTRY_NRSLOTS=512
CONFIG_XENO_OPT_SYS_HEAPSZ=256
CONFIG_XENO_OPT_SYS_STACKPOOLSZ=128
CONFIG_XENO_OPT_SEM_HEAPSZ=12
CONFIG_XENO_OPT_GLOBAL_SEM_HEAPSZ=12
CONFIG_XENO_OPT_STATS=y
CONFIG_XENO_OPT_DEBUG=y
# CONFIG_XENO_OPT_DEBUG_NUCLEUS is not set
# CONFIG_XENO_OPT_DEBUG_XNLOCK is not set
# CONFIG_XENO_OPT_DEBUG_QUEUES is not set
# CONFIG_XENO_OPT_DEBUG_REGISTRY is not set
# CONFIG_XENO_OPT_DEBUG_TIMERS is not set
CONFIG_XENO_OPT_DEBUG_SYNCH_RELAX=y
CONFIG_XENO_OPT_WATCHDOG=y
CONFIG_XENO_OPT_WATCHDOG_TIMEOUT=4
# CONFIG_XENO_OPT_SHIRQ is not set
CONFIG_XENO_OPT_SELECT=y
CONFIG_XENO_OPT_HOSTRT=y

#
# Timing
#
# CONFIG_XENO_OPT_TIMING_PERIODIC is not set
CONFIG_XENO_OPT_TIMING_VIRTICK=1000
CONFIG_XENO_OPT_TIMING_SCHEDLAT=0

#
# Scalability
#
# CONFIG_XENO_OPT_SCALABLE_SCHED is not set
CONFIG_XENO_OPT_TIMER_LIST=y
# CONFIG_XENO_OPT_TIMER_HEAP is not set
# CONFIG_XENO_OPT_TIMER_WHEEL is not set

#
# Machine
#
CONFIG_IPIPE_WANT_PREEMPTIBLE_SWITCH=y
CONFIG_IPIPE_WANT_ACTIVE_MM=y
CONFIG_SELECT_HW_UNLOCKED_SWITCH_ON_SMP=y
CONFIG_XENO_HW_FPU=y
CONFIG_XENO_HW_UNLOCKED_SWITCH=y

#
# Interfaces
#
CONFIG_XENO_SKIN_NATIVE=y
CONFIG_XENO_OPT_NATIVE_PERIOD=0
CONFIG_XENO_OPT_NATIVE_PIPE=y
CONFIG_XENO_OPT_NATIVE_PIPE_BUFSZ=1024
CONFIG_XENO_OPT_NATIVE_SEM=y
CONFIG_XENO_OPT_NATIVE_EVENT=y
CONFIG_XENO_OPT_NATIVE_MUTEX=y
CONFIG_XENO_OPT_NATIVE_COND=y
CONFIG_XENO_OPT_NATIVE_QUEUE=y
CONFIG_XENO_OPT_NATIVE_BUFFER=y
CONFIG_XENO_OPT_NATIVE_HEAP=y
CONFIG_XENO_OPT_NATIVE_ALARM=y
CONFIG_XENO_OPT_NATIVE_MPS=y
# CONFIG_XENO_OPT_NATIVE_INTR is not set
CONFIG_XENO_OPT_DEBUG_NATIVE=y
CONFIG_XENO_SKIN_POSIX=y
CONFIG_XENO_OPT_POSIX_PERIOD=0
# CONFIG_XENO_OPT_POSIX_SHM is not set
# CONFIG_XENO_OPT_POSIX_INTR is not set
CONFIG_XENO_OPT_POSIX_SELECT=y
CONFIG_XENO_OPT_DEBUG_POSIX=y
# CONFIG_XENO_SKIN_PSOS is not set
# CONFIG_XENO_SKIN_UITRON is not set
# CONFIG_XENO_SKIN_VRTX is not set
# CONFIG_XENO_SKIN_VXWORKS is not set
# CONFIG_XENO_OPT_NOWARN_DEPRECATED is not set
CONFIG_XENO_SKIN_RTDM=y
CONFIG_XENO_OPT_RTDM_PERIOD=0
CONFIG_XENO_OPT_RTDM_FILDES=128
CONFIG_XENO_OPT_RTDM_SELECT=y
# CONFIG_XENO_OPT_DEBUG_RTDM is not set
CONFIG_XENO_OPT_DEBUG_RTDM_APPL=y

#
# Drivers
#

#
# Serial drivers
#
# CONFIG_XENO_DRIVERS_16550A is not set

#
# Testing drivers
#
CONFIG_XENO_DRIVERS_TIMERBENCH=y
# CONFIG_XENO_DRIVERS_KLATENCY is not set
# CONFIG_XENO_DRIVERS_IRQBENCH is not set
CONFIG_XENO_DRIVERS_SWITCHTEST=y
# CONFIG_XENO_DRIVERS_RTDMTEST is not set

#
# CAN drivers
#
# CONFIG_XENO_DRIVERS_CAN is not set

#
# ANALOGY drivers
#
# CONFIG_XENO_DRIVERS_ANALOGY is not set

#
# Real-time IPC drivers
#
CONFIG_XENO_DRIVERS_RTIPC=y
CONFIG_XENO_DRIVERS_RTIPC_XDDP=y
CONFIG_XENO_DRIVERS_RTIPC_IDDP=y
CONFIG_XENO_OPT_IDDP_NRPORT=32
CONFIG_XENO_DRIVERS_RTIPC_BUFP=y
CONFIG_XENO_OPT_BUFP_NRPORT=32
CONFIG_FREEZER=y

#
# System Type
#
CONFIG_MMU=y
# CONFIG_ARCH_MULTIPLATFORM is not set
# CONFIG_ARCH_INTEGRATOR is not set
# CONFIG_ARCH_REALVIEW is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_AT91 is not set
# CONFIG_ARCH_BCM2835 is not set
# CONFIG_ARCH_CNS3XXX is not set
# CONFIG_ARCH_CLPS711X is not set
# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_SIRF is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
# CONFIG_ARCH_MXS is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IOP32X is not set
# CONFIG_ARCH_IOP33X is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_DOVE is not set
# CONFIG_ARCH_KIRKWOOD is not set
# CONFIG_ARCH_MV78XX0 is not set
# CONFIG_ARCH_ORION5X is not set
# CONFIG_ARCH_MMP is not set
# CONFIG_ARCH_KS8695 is not set
# CONFIG_ARCH_W90X900 is not set
# CONFIG_ARCH_LPC32XX is not set
# CONFIG_ARCH_TEGRA is not set
# CONFIG_ARCH_PXA is not set
# CONFIG_ARCH_MSM is not set
# CONFIG_ARCH_SHMOBILE is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C24XX is not set
# CONFIG_ARCH_S3C64XX is not set
# CONFIG_ARCH_S5P64X0 is not set
# CONFIG_ARCH_S5PC100 is not set
# CONFIG_ARCH_S5PV210 is not set
# CONFIG_ARCH_EXYNOS is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_U300 is not set
# CONFIG_ARCH_U8500 is not set
# CONFIG_ARCH_NOMADIK is not set
# CONFIG_PLAT_SPEAR is not set
# CONFIG_ARCH_DAVINCI is not set
CONFIG_ARCH_OMAP=y
# CONFIG_ARCH_VT8500_SINGLE is not set
CONFIG_GPIO_PCA953X=y
# CONFIG_KEYBOARD_GPIO_POLLED is not set

#
# TI OMAP Common Features
#
# CONFIG_ARCH_OMAP1 is not set
CONFIG_ARCH_OMAP2PLUS=y

#
# OMAP Feature Selections
#
CONFIG_OMAP_RESET_CLOCKS=y
CONFIG_OMAP_MUX=y
CONFIG_OMAP_MUX_DEBUG=y
CONFIG_OMAP_MUX_WARNINGS=y
CONFIG_OMAP_MBOX_FWK=y
CONFIG_OMAP_MBOX_KFIFO_SIZE=256
CONFIG_OMAP_32K_TIMER=y
CONFIG_OMAP_32K_TIMER_HZ=128
CONFIG_OMAP_DM_TIMER=y
CONFIG_OMAP_PM_NOOP=y
CONFIG_MACH_OMAP_GENERIC=y

#
# TI OMAP2/3/4 Specific Features
#
# CONFIG_ARCH_OMAP2PLUS_TYPICAL is not set
CONFIG_SOC_HAS_OMAP2_SDRC=y
CONFIG_SOC_HAS_REALTIME_COUNTER=y
# CONFIG_ARCH_OMAP2 is not set
# CONFIG_ARCH_OMAP3 is not set
# CONFIG_ARCH_OMAP4 is not set
CONFIG_SOC_OMAP5=y
# CONFIG_SOC_AM33XX is not set

#
# OMAP Board Type
#
# CONFIG_ARCH_VT8500 is not set
CONFIG_IPIPE_ARM_KUSER_TSC=y

#
# Processor Type
#
CONFIG_CPU_V7=y
CONFIG_CPU_32v6K=y
CONFIG_CPU_32v7=y
CONFIG_CPU_ABRT_EV7=y
CONFIG_CPU_PABRT_V7=y
CONFIG_CPU_CACHE_V7=y
CONFIG_CPU_CACHE_VIPT=y
CONFIG_CPU_COPY_V6=y
CONFIG_CPU_TLB_V7=y
CONFIG_CPU_HAS_ASID=y
CONFIG_CPU_CP15=y
CONFIG_CPU_CP15_MMU=y

#
# Processor Features
#
# CONFIG_ARM_LPAE is not set
# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
CONFIG_ARM_THUMB=y
CONFIG_ARM_THUMBEE=y
# CONFIG_ARM_VIRT_EXT is not set
CONFIG_SWP_EMULATE=y
# CONFIG_CPU_ICACHE_DISABLE is not set
# CONFIG_CPU_DCACHE_DISABLE is not set
# CONFIG_CPU_BPREDICT_DISABLE is not set
# CONFIG_CACHE_L2X0 is not set
CONFIG_ARM_L1_CACHE_SHIFT_6=y
CONFIG_ARM_L1_CACHE_SHIFT=6
CONFIG_ARM_DMA_MEM_BUFFERABLE=y
CONFIG_ARM_NR_BANKS=8
CONFIG_MULTI_IRQ_HANDLER=y
# CONFIG_ARM_ERRATA_430973 is not set
# CONFIG_ARM_ERRATA_458693 is not set
# CONFIG_ARM_ERRATA_460075 is not set
# CONFIG_ARM_ERRATA_742230 is not set
# CONFIG_ARM_ERRATA_742231 is not set
# CONFIG_ARM_ERRATA_720789 is not set
# CONFIG_ARM_ERRATA_743622 is not set
# CONFIG_ARM_ERRATA_751472 is not set
# CONFIG_ARM_ERRATA_754322 is not set
CONFIG_ARM_ERRATA_754327=y
# CONFIG_ARM_ERRATA_764369 is not set
# CONFIG_ARM_ERRATA_775420 is not set
# CONFIG_ARM_ERRATA_798181 is not set
CONFIG_ARM_GIC=y

#
# Bus support
#
# CONFIG_PCI_SYSCALL is not set
# CONFIG_PCCARD is not set

#
# Kernel Features
#
CONFIG_HAVE_SMP=y
CONFIG_SMP=y
CONFIG_SMP_ON_UP=y
CONFIG_ARM_CPU_TOPOLOGY=y
CONFIG_SCHED_MC=y
# CONFIG_SCHED_SMT is not set
CONFIG_HAVE_ARM_SCU=y
CONFIG_ARM_ARCH_TIMER=y
CONFIG_HAVE_ARM_TWD=y
# CONFIG_VMSPLIT_3G is not set
CONFIG_VMSPLIT_2G=y
# CONFIG_VMSPLIT_1G is not set
CONFIG_PAGE_OFFSET=0x80000000
CONFIG_NR_CPUS=2
CONFIG_HOTPLUG_CPU=y
CONFIG_LOCAL_TIMERS=y
CONFIG_ARCH_NR_GPIO=512
CONFIG_IPIPE=y
CONFIG_IPIPE_LEGACY=y
CONFIG_IPIPE_CORE=y
CONFIG_IPIPE_CORE_APIREV=2
CONFIG_IPIPE_WANT_APIREV_2=y
CONFIG_IPIPE_TARGET_APIREV=2
CONFIG_IPIPE_HAVE_HOSTRT=y
CONFIG_IPIPE_DELAYED_ATOMICSW=y
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_PREEMPT_COUNT=y
CONFIG_HZ=128
# CONFIG_THUMB2_KERNEL is not set
CONFIG_AEABI=y
CONFIG_OABI_COMPAT=y
CONFIG_ARCH_HAS_HOLES_MEMORYMODEL=y
# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
CONFIG_HAVE_ARCH_PFN_VALID=y
# CONFIG_HIGHMEM is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_HAVE_MEMBLOCK=y
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_COMPACTION is not set
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_CROSS_MEMORY_ATTACH=y
# CONFIG_CLEANCACHE is not set
# CONFIG_FRONTSWAP is not set
CONFIG_FORCE_MAX_ZONEORDER=11
CONFIG_ALIGNMENT_TRAP=y
# CONFIG_UACCESS_WITH_MEMCPY is not set
# CONFIG_SECCOMP is not set
# CONFIG_CC_STACKPROTECTOR is not set
# CONFIG_XEN is not set

#
# Boot options
#
CONFIG_USE_OF=y
CONFIG_ATAGS=y
# CONFIG_DEPRECATED_PARAM_STRUCT is not set
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
# CONFIG_ARM_APPENDED_DTB is not set
CONFIG_CMDLINE="root=/dev/mmcblk0p2 rootwait console=ttyO2,115200"
CONFIG_CMDLINE_FROM_BOOTLOADER=y
# CONFIG_CMDLINE_EXTEND is not set
# CONFIG_CMDLINE_FORCE is not set
# CONFIG_XIP_KERNEL is not set
CONFIG_KEXEC=y
CONFIG_ATAGS_PROC=y
# CONFIG_CRASH_DUMP is not set
# CONFIG_AUTO_ZRELADDR is not set

#
# CPU Power Management
#

#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set
# CONFIG_CPU_IDLE is not set
# CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED is not set

#
# Floating point emulation
#

#
# At least one emulation must be selected
#
# CONFIG_FPE_NWFPE is not set
# CONFIG_FPE_FASTFPE is not set
CONFIG_VFP=y
CONFIG_VFPv3=y
CONFIG_NEON=y

#
# Userspace binary formats
#
CONFIG_BINFMT_ELF=y
CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS=y
CONFIG_HAVE_AOUT=y
# CONFIG_BINFMT_AOUT is not set
CONFIG_BINFMT_MISC=y
CONFIG_COREDUMP=y

#
# Power management options
#
CONFIG_SUSPEND=y
CONFIG_SUSPEND_FREEZER=y
CONFIG_PM_SLEEP=y
CONFIG_PM_SLEEP_SMP=y
# CONFIG_PM_AUTOSLEEP is not set
# CONFIG_PM_WAKELOCKS is not set
CONFIG_PM_RUNTIME=y
CONFIG_PM=y
# CONFIG_PM_DEBUG is not set
# CONFIG_APM_EMULATION is not set
CONFIG_PM_CLK=y
CONFIG_CPU_PM=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_ARM_CPU_SUSPEND=y
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_DIAG is not set
CONFIG_UNIX=y
# CONFIG_UNIX_DIAG is not set
CONFIG_XFRM=y
CONFIG_XFRM_ALGO=y
CONFIG_XFRM_USER=y
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_XFRM_MIGRATE=y
# CONFIG_XFRM_STATISTICS is not set
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE_DEMUX is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_NET_IPVTI is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_XFRM_TUNNEL is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_INET_UDP_DIAG is not set
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
# CONFIG_IPV6 is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETWORK_PHY_TIMESTAMPING is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_NETFILTER_ADVANCED=y

#
# Core Netfilter Configuration
#
# CONFIG_NETFILTER_NETLINK_ACCT is not set
# CONFIG_NETFILTER_NETLINK_QUEUE is not set
# CONFIG_NETFILTER_NETLINK_LOG is not set
# CONFIG_NF_CONNTRACK is not set
# CONFIG_NETFILTER_XTABLES is not set
# CONFIG_IP_VS is not set

#
# IP: Netfilter Configuration
#
# CONFIG_NF_DEFRAG_IPV4 is not set
# CONFIG_IP_NF_QUEUE is not set
# CONFIG_IP_NF_IPTABLES is not set
# CONFIG_IP_NF_ARPTABLES is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_L2TP is not set
# CONFIG_BRIDGE is not set
CONFIG_HAVE_NET_DSA=y
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_PHONET is not set
# CONFIG_IEEE802154 is not set
# CONFIG_NET_SCHED is not set
# CONFIG_DCB is not set
CONFIG_DNS_RESOLVER=y
# CONFIG_BATMAN_ADV is not set
# CONFIG_OPENVSWITCH is not set
CONFIG_RPS=y
CONFIG_RFS_ACCEL=y
CONFIG_XPS=y
CONFIG_BQL=y
# CONFIG_BPF_JIT is not set

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NET_DROP_MONITOR is not set
# CONFIG_HAMRADIO is not set
# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
# CONFIG_WIRELESS is not set
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_RFKILL_REGULATOR is not set
# CONFIG_NET_9P is not set
# CONFIG_CAIF is not set
# CONFIG_CEPH_LIB is not set
# CONFIG_NFC is not set
CONFIG_HAVE_BPF_JIT=y

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
CONFIG_FIRMWARE_IN_KERNEL=y
CONFIG_EXTRA_FIRMWARE=""
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_GENERIC_CPU_DEVICES is not set
CONFIG_REGMAP=y
CONFIG_REGMAP_I2C=y
CONFIG_REGMAP_IRQ=y
# CONFIG_DMA_SHARED_BUFFER is not set
# CONFIG_CMA is not set

#
# Bus devices
#
# CONFIG_OMAP_OCP2SCP is not set
CONFIG_OMAP_INTERCONNECT=y
# CONFIG_CONNECTOR is not set
# CONFIG_MTD is not set
CONFIG_DTC=y
CONFIG_OF=y

#
# Device Tree and Open Firmware support
#
CONFIG_PROC_DEVICETREE=y
# CONFIG_OF_SELFTEST is not set
CONFIG_OF_FLATTREE=y
CONFIG_OF_EARLY_FLATTREE=y
CONFIG_OF_ADDRESS=y
CONFIG_OF_IRQ=y
CONFIG_OF_DEVICE=y
CONFIG_OF_I2C=y
CONFIG_OF_NET=y
CONFIG_OF_MDIO=y
# CONFIG_PARPORT is not set
CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_LOOP_MIN_COUNT=8
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_DRBD is not set
# CONFIG_BLK_DEV_NBD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=16384
# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
# CONFIG_MG_DISK is not set
# CONFIG_BLK_DEV_RBD is not set

#
# Misc devices
#
# CONFIG_SENSORS_LIS3LV02D is not set
# CONFIG_AD525X_DPOT is not set
# CONFIG_ATMEL_PWM is not set
# CONFIG_ICS932S401 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_APDS9802ALS is not set
# CONFIG_ISL29003 is not set
# CONFIG_ISL29020 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_SENSORS_BH1780 is not set
# CONFIG_SENSORS_BH1770 is not set
# CONFIG_SENSORS_APDS990X is not set
# CONFIG_HMC6352 is not set
# CONFIG_DS1682 is not set
# CONFIG_BMP085_I2C is not set
# CONFIG_USB_SWITCH_FSA9480 is not set
# CONFIG_C2PORT is not set

#
# EEPROM support
#
# CONFIG_EEPROM_AT24 is not set
# CONFIG_EEPROM_LEGACY is not set
# CONFIG_EEPROM_MAX6875 is not set
CONFIG_EEPROM_93CX6=y

#
# Texas Instruments shared transport line discipline
#
# CONFIG_TI_ST is not set
# CONFIG_SENSORS_LIS3_I2C is not set

#
# Altera FPGA firmware download module
#
# CONFIG_ALTERA_STAPL is not set

#
# SCSI device support
#
CONFIG_SCSI_MOD=y
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
# CONFIG_CHR_DEV_SG is not set
# CONFIG_CHR_DEV_SCH is not set
CONFIG_SCSI_MULTI_LUN=y
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
CONFIG_SCSI_SCAN_ASYNC=y

#
# SCSI Transports
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
# CONFIG_SCSI_SRP_ATTRS is not set
# CONFIG_SCSI_LOWLEVEL is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
# CONFIG_TARGET_CORE is not set
CONFIG_NETDEVICES=y
CONFIG_NET_CORE=y
# CONFIG_BONDING is not set
# CONFIG_DUMMY is not set
# CONFIG_EQUALIZER is not set
CONFIG_MII=y
# CONFIG_NET_TEAM is not set
# CONFIG_MACVLAN is not set
# CONFIG_VXLAN is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_TUN is not set
# CONFIG_VETH is not set

#
# CAIF transport drivers
#

#
# Distributed Switch Architecture drivers
#
# CONFIG_NET_DSA_MV88E6XXX is not set
# CONFIG_NET_DSA_MV88E6060 is not set
# CONFIG_NET_DSA_MV88E6XXX_NEED_PPU is not set
# CONFIG_NET_DSA_MV88E6131 is not set
# CONFIG_NET_DSA_MV88E6123_61_65 is not set
CONFIG_ETHERNET=y
# CONFIG_NET_CADENCE is not set
# CONFIG_NET_VENDOR_BROADCOM is not set
# CONFIG_NET_CALXEDA_XGMAC is not set
# CONFIG_NET_VENDOR_CIRRUS is not set
# CONFIG_DM9000 is not set
# CONFIG_DNET is not set
# CONFIG_NET_VENDOR_FARADAY is not set
# CONFIG_NET_VENDOR_INTEL is not set
# CONFIG_NET_VENDOR_MARVELL is not set
# CONFIG_NET_VENDOR_MICREL is not set
# CONFIG_NET_VENDOR_NATSEMI is not set
# CONFIG_ETHOC is not set
# CONFIG_NET_VENDOR_SEEQ is not set
# CONFIG_NET_VENDOR_SMSC is not set
# CONFIG_NET_VENDOR_STMICRO is not set
# CONFIG_NET_VENDOR_WIZNET is not set
CONFIG_PHYLIB=y

#
# MII PHY device drivers
#
# CONFIG_AT803X_PHY is not set
# CONFIG_AMD_PHY is not set
# CONFIG_MARVELL_PHY is not set
# CONFIG_DAVICOM_PHY is not set
# CONFIG_QSEMI_PHY is not set
# CONFIG_LXT_PHY is not set
# CONFIG_CICADA_PHY is not set
# CONFIG_VITESSE_PHY is not set
# CONFIG_SMSC_PHY is not set
# CONFIG_BROADCOM_PHY is not set
# CONFIG_BCM87XX_PHY is not set
# CONFIG_ICPLUS_PHY is not set
# CONFIG_REALTEK_PHY is not set
# CONFIG_NATIONAL_PHY is not set
# CONFIG_STE10XP is not set
# CONFIG_LSI_ET1011C_PHY is not set
# CONFIG_MICREL_PHY is not set
# CONFIG_FIXED_PHY is not set
# CONFIG_MDIO_BITBANG is not set
# CONFIG_MDIO_BUS_MUX_GPIO is not set
# CONFIG_MDIO_BUS_MUX_MMIOREG is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set

#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
CONFIG_USB_USBNET=y
# CONFIG_USB_NET_AX8817X is not set
# CONFIG_USB_NET_CDCETHER is not set
# CONFIG_USB_NET_CDC_EEM is not set
# CONFIG_USB_NET_CDC_NCM is not set
# CONFIG_USB_NET_CDC_MBIM is not set
# CONFIG_USB_NET_DM9601 is not set
# CONFIG_USB_NET_SMSC75XX is not set
CONFIG_USB_NET_SMSC95XX=y
# CONFIG_USB_NET_GL620A is not set
# CONFIG_USB_NET_NET1080 is not set
# CONFIG_USB_NET_PLUSB is not set
# CONFIG_USB_NET_MCS7830 is not set
# CONFIG_USB_NET_RNDIS_HOST is not set
# CONFIG_USB_NET_CDC_SUBSET is not set
# CONFIG_USB_NET_ZAURUS is not set
# CONFIG_USB_NET_CX82310_ETH is not set
# CONFIG_USB_NET_KALMIA is not set
# CONFIG_USB_NET_QMI_WWAN is not set
# CONFIG_USB_NET_INT51X1 is not set
# CONFIG_USB_IPHETH is not set
# CONFIG_USB_SIERRA_NET is not set
# CONFIG_WLAN is not set

#
# Enable WiMAX (Networking options) to see the WiMAX drivers
#
# CONFIG_WAN is not set
# CONFIG_ISDN is not set

#
# Input device support
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
# CONFIG_INPUT_POLLDEV is not set
# CONFIG_INPUT_SPARSEKMAP is not set
# CONFIG_INPUT_MATRIXKMAP is not set

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=y
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
# CONFIG_KEYBOARD_ADP5588 is not set
# CONFIG_KEYBOARD_ADP5589 is not set
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_QT1070 is not set
# CONFIG_KEYBOARD_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
CONFIG_KEYBOARD_GPIO=y
# CONFIG_KEYBOARD_TCA6416 is not set
# CONFIG_KEYBOARD_TCA8418 is not set
# CONFIG_KEYBOARD_MATRIX is not set
# CONFIG_KEYBOARD_LM8323 is not set
# CONFIG_KEYBOARD_LM8333 is not set
# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_MCS is not set
# CONFIG_KEYBOARD_MPR121 is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_SAMSUNG is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_OMAP4 is not set
# CONFIG_KEYBOARD_XTKBD is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_LOGIPS2PP=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
CONFIG_MOUSE_PS2_TRACKPOINT=y
# CONFIG_MOUSE_PS2_ELANTECH is not set
# CONFIG_MOUSE_PS2_SENTELIC is not set
# CONFIG_MOUSE_PS2_TOUCHKIT is not set
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_BCM5974 is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_MOUSE_GPIO is not set
# CONFIG_MOUSE_SYNAPTICS_I2C is not set
# CONFIG_MOUSE_SYNAPTICS_USB is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
# CONFIG_INPUT_AD714X is not set
# CONFIG_INPUT_BMA150 is not set
# CONFIG_INPUT_MMA8450 is not set
# CONFIG_INPUT_MPU3050 is not set
# CONFIG_INPUT_GP2A is not set
# CONFIG_INPUT_GPIO_TILT_POLLED is not set
# CONFIG_INPUT_ATI_REMOTE2 is not set
# CONFIG_INPUT_KEYSPAN_REMOTE is not set
# CONFIG_INPUT_KXTJ9 is not set
# CONFIG_INPUT_POWERMATE is not set
# CONFIG_INPUT_YEALINK is not set
# CONFIG_INPUT_CM109 is not set
# CONFIG_INPUT_TWL6040_VIBRA is not set
# CONFIG_INPUT_UINPUT is not set
# CONFIG_INPUT_PCF8574 is not set
# CONFIG_INPUT_GPIO_ROTARY_ENCODER is not set
# CONFIG_INPUT_ADXL34X is not set
# CONFIG_INPUT_CMA3000 is not set
# CONFIG_INPUT_PALMAS_PWRBUTTON is not set

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_SERPORT=y
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_SERIO_ALTERA_PS2 is not set
# CONFIG_SERIO_PS2MULT is not set
# CONFIG_SERIO_ARC_PS2 is not set
# CONFIG_GAMEPORT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_VT_CONSOLE_SLEEP=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_UNIX98_PTYS=y
# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
# CONFIG_LEGACY_PTYS is not set
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_N_GSM is not set
# CONFIG_TRACE_SINK is not set
CONFIG_DEVKMEM=y

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=32
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
CONFIG_SERIAL_8250_DETECT_IRQ=y
CONFIG_SERIAL_8250_RSA=y
# CONFIG_SERIAL_8250_DW is not set
# CONFIG_SERIAL_8250_EM is not set

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_OF_PLATFORM is not set
CONFIG_SERIAL_OMAP=y
CONFIG_SERIAL_OMAP_CONSOLE=y
# CONFIG_SERIAL_SCCNXP is not set
# CONFIG_SERIAL_TIMBERDALE is not set
# CONFIG_SERIAL_ALTERA_JTAGUART is not set
# CONFIG_SERIAL_ALTERA_UART is not set
# CONFIG_SERIAL_XILINX_PS_UART is not set
# CONFIG_SERIAL_ARC is not set
# CONFIG_TTY_PRINTK is not set
# CONFIG_HVC_DCC is not set
# CONFIG_IPMI_HANDLER is not set
CONFIG_HW_RANDOM=y
# CONFIG_HW_RANDOM_TIMERIOMEM is not set
# CONFIG_HW_RANDOM_ATMEL is not set
# CONFIG_HW_RANDOM_EXYNOS is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=y
# CONFIG_I2C_MUX is not set
CONFIG_I2C_HELPER_AUTO=y

#
# I2C Hardware Bus support
#

#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
# CONFIG_I2C_CBUS_GPIO is not set
# CONFIG_I2C_DESIGNWARE_PLATFORM is not set
# CONFIG_I2C_GPIO is not set
# CONFIG_I2C_OCORES is not set
CONFIG_I2C_OMAP=y
# CONFIG_I2C_PCA_PLATFORM is not set
# CONFIG_I2C_PXA_PCI is not set
# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_XILINX is not set

#
# External I2C/SMBus adapter drivers
#
# CONFIG_I2C_DIOLAN_U2C is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_TAOS_EVM is not set
# CONFIG_I2C_TINY_USB is not set

#
# Other I2C/SMBus bus drivers
#
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_SPI is not set
# CONFIG_HSI is not set

#
# PPS support
#
# CONFIG_PPS is not set

#
# PPS generators support
#

#
# PTP clock support
#
# CONFIG_PTP_1588_CLOCK is not set

#
# Enable PHYLIB and NETWORK_PHY_TIMESTAMPING to see the additional clocks.
#
# CONFIG_PTP_1588_CLOCK_PCH is not set
CONFIG_PINCTRL=y

#
# Pin controllers
#
CONFIG_PINMUX=y
CONFIG_PINCONF=y
# CONFIG_DEBUG_PINCTRL is not set
CONFIG_PINCTRL_SINGLE=y
# CONFIG_PINCTRL_EXYNOS is not set
# CONFIG_PINCTRL_EXYNOS5440 is not set
CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
CONFIG_ARCH_REQUIRE_GPIOLIB=y
CONFIG_GPIOLIB=y
CONFIG_OF_GPIO=y
CONFIG_DEBUG_GPIO=y
CONFIG_GPIO_SYSFS=y

#
# Memory mapped GPIO drivers:
#
# CONFIG_GPIO_GENERIC_PLATFORM is not set
# CONFIG_GPIO_EM is not set
# CONFIG_GPIO_TS5500 is not set

#
# I2C GPIO expanders:
#
# CONFIG_GPIO_MAX7300 is not set
# CONFIG_GPIO_MAX732X is not set
CONFIG_GPIO_PCA953X_IRQ=y
# CONFIG_GPIO_PCF857X is not set
# CONFIG_GPIO_SX150X is not set
# CONFIG_GPIO_TWL6040 is not set
# CONFIG_GPIO_ADP5588 is not set
# CONFIG_GPIO_ADNP is not set

#
# PCI GPIO expanders:
#

#
# SPI GPIO expanders:
#
# CONFIG_GPIO_MCP23S08 is not set

#
# AC97 GPIO expanders:
#

#
# MODULbus GPIO expanders:
#
# CONFIG_GPIO_PALMAS is not set

#
# USB GPIO expanders:
#
CONFIG_W1=y

#
# 1-wire Bus Masters
#
# CONFIG_W1_MASTER_DS2490 is not set
# CONFIG_W1_MASTER_DS2482 is not set
# CONFIG_W1_MASTER_DS1WM is not set
# CONFIG_W1_MASTER_GPIO is not set
# CONFIG_HDQ_MASTER_OMAP is not set

#
# 1-wire Slaves
#
# CONFIG_W1_SLAVE_THERM is not set
# CONFIG_W1_SLAVE_SMEM is not set
# CONFIG_W1_SLAVE_DS2408 is not set
# CONFIG_W1_SLAVE_DS2423 is not set
# CONFIG_W1_SLAVE_DS2431 is not set
# CONFIG_W1_SLAVE_DS2433 is not set
# CONFIG_W1_SLAVE_DS2760 is not set
# CONFIG_W1_SLAVE_DS2780 is not set
# CONFIG_W1_SLAVE_DS2781 is not set
# CONFIG_W1_SLAVE_DS28E04 is not set
# CONFIG_W1_SLAVE_BQ27000 is not set
CONFIG_POWER_SUPPLY=y
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_PDA_POWER is not set
# CONFIG_TEST_POWER is not set
# CONFIG_BATTERY_DS2780 is not set
# CONFIG_BATTERY_DS2781 is not set
# CONFIG_BATTERY_DS2782 is not set
# CONFIG_BATTERY_SBS is not set
# CONFIG_BATTERY_BQ27x00 is not set
# CONFIG_BATTERY_MAX17040 is not set
# CONFIG_BATTERY_MAX17042 is not set
# CONFIG_CHARGER_ISP1704 is not set
# CONFIG_CHARGER_MAX8903 is not set
# CONFIG_CHARGER_LP8727 is not set
# CONFIG_CHARGER_GPIO is not set
# CONFIG_CHARGER_MANAGER is not set
# CONFIG_CHARGER_BQ2415X is not set
# CONFIG_CHARGER_SMB347 is not set
# CONFIG_POWER_RESET is not set
# CONFIG_POWER_AVS is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
# CONFIG_HWMON_DEBUG_CHIP is not set

#
# Native drivers
#
# CONFIG_SENSORS_AD7414 is not set
# CONFIG_SENSORS_AD7418 is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1029 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ADT7410 is not set
# CONFIG_SENSORS_ADT7411 is not set
# CONFIG_SENSORS_ADT7462 is not set
# CONFIG_SENSORS_ADT7470 is not set
# CONFIG_SENSORS_ADT7475 is not set
# CONFIG_SENSORS_ASC7621 is not set
# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS620 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_F75375S is not set
# CONFIG_SENSORS_G760A is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_GL520SM is not set
# CONFIG_SENSORS_GPIO_FAN is not set
# CONFIG_SENSORS_HIH6130 is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_JC42 is not set
# CONFIG_SENSORS_LINEAGE is not set
# CONFIG_SENSORS_LM63 is not set
# CONFIG_SENSORS_LM73 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# CONFIG_SENSORS_LM80 is not set
# CONFIG_SENSORS_LM83 is not set
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_LM93 is not set
# CONFIG_SENSORS_LTC4151 is not set
# CONFIG_SENSORS_LTC4215 is not set
# CONFIG_SENSORS_LTC4245 is not set
# CONFIG_SENSORS_LTC4261 is not set
# CONFIG_SENSORS_LM95241 is not set
# CONFIG_SENSORS_LM95245 is not set
# CONFIG_SENSORS_MAX16065 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_MAX1668 is not set
# CONFIG_SENSORS_MAX197 is not set
# CONFIG_SENSORS_MAX6639 is not set
# CONFIG_SENSORS_MAX6642 is not set
# CONFIG_SENSORS_MAX6650 is not set
# CONFIG_SENSORS_MCP3021 is not set
# CONFIG_SENSORS_NTC_THERMISTOR is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_PMBUS is not set
# CONFIG_SENSORS_SHT15 is not set
# CONFIG_SENSORS_SHT21 is not set
# CONFIG_SENSORS_SMM665 is not set
# CONFIG_SENSORS_DME1737 is not set
# CONFIG_SENSORS_EMC1403 is not set
# CONFIG_SENSORS_EMC2103 is not set
# CONFIG_SENSORS_EMC6W201 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_SCH56XX_COMMON is not set
# CONFIG_SENSORS_SCH5627 is not set
# CONFIG_SENSORS_SCH5636 is not set
# CONFIG_SENSORS_ADS1015 is not set
# CONFIG_SENSORS_ADS7828 is not set
# CONFIG_SENSORS_AMC6821 is not set
# CONFIG_SENSORS_INA2XX is not set
# CONFIG_SENSORS_THMC50 is not set
# CONFIG_SENSORS_TMP102 is not set
# CONFIG_SENSORS_TMP401 is not set
# CONFIG_SENSORS_TMP421 is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83792D is not set
# CONFIG_SENSORS_W83793 is not set
# CONFIG_SENSORS_W83795 is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83L786NG is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_THERMAL is not set
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_CORE=y
# CONFIG_WATCHDOG_NOWAYOUT is not set

#
# Watchdog Device Drivers
#
# CONFIG_SOFT_WATCHDOG is not set
# CONFIG_PALMAS_WATCHDOG is not set
# CONFIG_DW_WATCHDOG is not set
# CONFIG_MPCORE_WATCHDOG is not set
CONFIG_OMAP_WATCHDOG=y
# CONFIG_MAX63XX_WATCHDOG is not set

#
# USB-based Watchdog Cards
#
# CONFIG_USBPCWATCHDOG is not set
CONFIG_SSB_POSSIBLE=y

#
# Sonics Silicon Backplane
#
# CONFIG_SSB is not set
CONFIG_BCMA_POSSIBLE=y

#
# Broadcom specific AMBA
#
# CONFIG_BCMA is not set

#
# Multifunction device drivers
#
CONFIG_MFD_CORE=y
# CONFIG_MFD_88PM860X is not set
# CONFIG_MFD_88PM800 is not set
# CONFIG_MFD_88PM805 is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_MFD_ASIC3 is not set
# CONFIG_MFD_TI_AM335X_TSCADC is not set
# CONFIG_HTC_EGPIO is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_HTC_I2CPLD is not set
# CONFIG_MFD_LM3533 is not set
# CONFIG_TPS6105X is not set
# CONFIG_TPS65010 is not set
# CONFIG_TPS6507X is not set
CONFIG_MFD_TPS65217=y
# CONFIG_MFD_TPS6586X is not set
# CONFIG_MFD_TPS65910 is not set
# CONFIG_MFD_TPS65912_I2C is not set
# CONFIG_MFD_TPS80031 is not set
# CONFIG_TWL4030_CORE is not set
CONFIG_TWL6040_CORE=y
# CONFIG_MFD_STMPE is not set
# CONFIG_MFD_TC3589X is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_MFD_T7L66XB is not set
# CONFIG_MFD_SMSC is not set
# CONFIG_MFD_TC6387XB is not set
# CONFIG_MFD_TC6393XB is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_DA9052_I2C is not set
# CONFIG_MFD_DA9055 is not set
# CONFIG_PMIC_ADP5520 is not set
# CONFIG_MFD_LP8788 is not set
# CONFIG_MFD_MAX77686 is not set
# CONFIG_MFD_MAX77693 is not set
# CONFIG_MFD_MAX8907 is not set
# CONFIG_MFD_MAX8925 is not set
# CONFIG_MFD_MAX8997 is not set
# CONFIG_MFD_MAX8998 is not set
# CONFIG_MFD_SEC_CORE is not set
# CONFIG_MFD_ARIZONA_I2C is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_WM831X_I2C is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_WM8994 is not set
# CONFIG_MFD_PCF50633 is not set
# CONFIG_MFD_MC13XXX_I2C is not set
# CONFIG_ABX500_CORE is not set
# CONFIG_MFD_WL1273_CORE is not set
CONFIG_MFD_OMAP_USB_HOST=y
# CONFIG_MFD_TPS65090 is not set
# CONFIG_MFD_AAT2870_CORE is not set
# CONFIG_MFD_RC5T583 is not set
# CONFIG_MFD_SYSCON is not set
CONFIG_MFD_PALMAS=y
CONFIG_MFD_PALMAS_GPADC=y
CONFIG_MFD_PALMAS_PWM=y
CONFIG_MFD_PALMAS_RESOURCE=y
# CONFIG_MFD_VIPERBOARD is not set
# CONFIG_MFD_RETU is not set
# CONFIG_MFD_AS3711 is not set
CONFIG_REGULATOR=y
# CONFIG_REGULATOR_DEBUG is not set
# CONFIG_REGULATOR_DUMMY is not set
CONFIG_REGULATOR_FIXED_VOLTAGE=y
# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
# CONFIG_REGULATOR_GPIO is not set
# CONFIG_REGULATOR_AD5398 is not set
# CONFIG_REGULATOR_FAN53555 is not set
# CONFIG_REGULATOR_ISL6271A is not set
# CONFIG_REGULATOR_MAX1586 is not set
# CONFIG_REGULATOR_MAX8649 is not set
# CONFIG_REGULATOR_MAX8660 is not set
# CONFIG_REGULATOR_MAX8952 is not set
# CONFIG_REGULATOR_MAX8973 is not set
# CONFIG_REGULATOR_LP3971 is not set
# CONFIG_REGULATOR_LP3972 is not set
# CONFIG_REGULATOR_LP872X is not set
CONFIG_REGULATOR_PALMAS=y
# CONFIG_REGULATOR_TPS51632 is not set
# CONFIG_REGULATOR_TPS62360 is not set
CONFIG_REGULATOR_TPS65023=y
CONFIG_REGULATOR_TPS6507X=y
CONFIG_REGULATOR_TPS65217=y
# CONFIG_MEDIA_SUPPORT is not set

#
# Graphics support
#
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_FB is not set
# CONFIG_OMAP2_DSS is not set
# CONFIG_EXYNOS_VIDEO is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set

#
# Console display driver support
#
CONFIG_DUMMY_CONSOLE=y
# CONFIG_SOUND is not set

#
# HID support
#
CONFIG_HID=y
# CONFIG_HID_BATTERY_STRENGTH is not set
# CONFIG_HIDRAW is not set
# CONFIG_UHID is not set
CONFIG_HID_GENERIC=y

#
# Special HID drivers
#
# CONFIG_HID_A4TECH is not set
# CONFIG_HID_ACRUX is not set
# CONFIG_HID_APPLE is not set
# CONFIG_HID_AUREAL is not set
# CONFIG_HID_BELKIN is not set
# CONFIG_HID_CHERRY is not set
# CONFIG_HID_CHICONY is not set
# CONFIG_HID_CYPRESS is not set
# CONFIG_HID_DRAGONRISE is not set
# CONFIG_HID_EMS_FF is not set
# CONFIG_HID_EZKEY is not set
# CONFIG_HID_HOLTEK is not set
# CONFIG_HID_KEYTOUCH is not set
# CONFIG_HID_KYE is not set
# CONFIG_HID_UCLOGIC is not set
# CONFIG_HID_WALTOP is not set
# CONFIG_HID_GYRATION is not set
# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
# CONFIG_HID_LCPOWER is not set
# CONFIG_HID_LENOVO_TPKBD is not set
# CONFIG_HID_LOGITECH is not set
# CONFIG_HID_MICROSOFT is not set
# CONFIG_HID_MONTEREY is not set
# CONFIG_HID_MULTITOUCH is not set
# CONFIG_HID_NTRIG is not set
# CONFIG_HID_ORTEK is not set
# CONFIG_HID_PANTHERLORD is not set
# CONFIG_HID_PETALYNX is not set
# CONFIG_HID_PICOLCD is not set
# CONFIG_HID_PRIMAX is not set
# CONFIG_HID_ROCCAT is not set
# CONFIG_HID_SAITEK is not set
# CONFIG_HID_SAMSUNG is not set
# CONFIG_HID_SONY is not set
# CONFIG_HID_SPEEDLINK is not set
# CONFIG_HID_SUNPLUS is not set
# CONFIG_HID_GREENASIA is not set
# CONFIG_HID_SMARTJOYPLUS is not set
# CONFIG_HID_TIVO is not set
# CONFIG_HID_TOPSEED is not set
# CONFIG_HID_THRUSTMASTER is not set
# CONFIG_HID_ZEROPLUS is not set
# CONFIG_HID_ZYDACRON is not set
# CONFIG_HID_SENSOR_HUB is not set

#
# USB HID support
#
CONFIG_USB_HID=y
# CONFIG_HID_PID is not set
# CONFIG_USB_HIDDEV is not set

#
# I2C HID support
#
# CONFIG_I2C_HID is not set
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
# CONFIG_USB_ARCH_HAS_XHCI is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_COMMON=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y

#
# Miscellaneous USB options
#
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG_WHITELIST is not set
# CONFIG_USB_OTG_BLACKLIST_HUB is not set
CONFIG_USB_MON=y
# CONFIG_USB_WUSB_CBAF is not set

#
# USB Host Controller Drivers
#
# CONFIG_USB_C67X00_HCD is not set
CONFIG_USB_EHCI_HCD=y
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
CONFIG_USB_EHCI_TT_NEWSCHED=y
CONFIG_USB_EHCI_HCD_OMAP=y
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
# CONFIG_USB_ISP1362_HCD is not set
# CONFIG_USB_OHCI_HCD is not set
# CONFIG_USB_EHCI_HCD_PLATFORM is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
# CONFIG_USB_CHIPIDEA is not set

#
# USB Device Class drivers
#
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
CONFIG_USB_WDM=y
# CONFIG_USB_TMC is not set

#
# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
#

#
# also be needed; see USB_STORAGE Help for more info
#
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_REALTEK is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
# CONFIG_USB_STORAGE_ONETOUCH is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
# CONFIG_USB_STORAGE_ENE_UB6250 is not set

#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set

#
# USB port drivers
#
# CONFIG_USB_SERIAL is not set

#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_SEVSEG is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_YUREX is not set
# CONFIG_USB_EZUSB_FX2 is not set

#
# USB Physical Layer drivers
#
# CONFIG_OMAP_USB2 is not set
# CONFIG_USB_ISP1301 is not set
# CONFIG_USB_RCAR_PHY is not set
# CONFIG_USB_GADGET is not set

#
# OTG and related infrastructure
#
CONFIG_USB_OTG_UTILS=y
# CONFIG_USB_GPIO_VBUS is not set
# CONFIG_USB_ULPI is not set
CONFIG_NOP_USB_XCEIV=y
# CONFIG_PALMAS_USB is not set
CONFIG_MMC=y
# CONFIG_MMC_DEBUG is not set
CONFIG_MMC_UNSAFE_RESUME=y
# CONFIG_MMC_CLKGATE is not set

#
# MMC/SD/SDIO Card Drivers
#
CONFIG_MMC_BLOCK=y
CONFIG_MMC_BLOCK_MINORS=8
CONFIG_MMC_BLOCK_BOUNCE=y
CONFIG_SDIO_UART=y
# CONFIG_MMC_TEST is not set

#
# MMC/SD/SDIO Host Controller Drivers
#
# CONFIG_MMC_SDHCI is not set
# CONFIG_MMC_SDHCI_PXAV3 is not set
# CONFIG_MMC_SDHCI_PXAV2 is not set
CONFIG_MMC_OMAP=y
CONFIG_MMC_OMAP_HS=y
# CONFIG_MMC_DW is not set
# CONFIG_MMC_VUB300 is not set
# CONFIG_MMC_USHC is not set
# CONFIG_MEMSTICK is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y

#
# LED drivers
#
# CONFIG_LEDS_LM3530 is not set
# CONFIG_LEDS_LM3642 is not set
# CONFIG_LEDS_PCA9532 is not set
CONFIG_LEDS_GPIO=y
# CONFIG_LEDS_LP3944 is not set
# CONFIG_LEDS_LP5521 is not set
# CONFIG_LEDS_LP5523 is not set
# CONFIG_LEDS_PCA955X is not set
# CONFIG_LEDS_PCA9633 is not set
# CONFIG_LEDS_REGULATOR is not set
# CONFIG_LEDS_BD2802 is not set
# CONFIG_LEDS_LT3593 is not set
# CONFIG_LEDS_RENESAS_TPU is not set
# CONFIG_LEDS_TCA6507 is not set
# CONFIG_LEDS_LM355x is not set
# CONFIG_LEDS_OT200 is not set
# CONFIG_LEDS_BLINKM is not set
# CONFIG_LEDS_PALMAS is not set
CONFIG_LEDS_TRIGGERS=y

#
# LED Triggers
#
# CONFIG_LEDS_TRIGGER_TIMER is not set
# CONFIG_LEDS_TRIGGER_ONESHOT is not set
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
# CONFIG_LEDS_TRIGGER_CPU is not set
# CONFIG_LEDS_TRIGGER_GPIO is not set
# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set

#
# iptables trigger is under Netfilter config (LED target)
#
# CONFIG_LEDS_TRIGGER_TRANSIENT is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_EDAC is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
# CONFIG_RTC_DEBUG is not set

#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
# CONFIG_RTC_DRV_TEST is not set

#
# I2C RTC drivers
#
# CONFIG_RTC_DRV_DS1307 is not set
# CONFIG_RTC_DRV_DS1374 is not set
# CONFIG_RTC_DRV_DS1672 is not set
# CONFIG_RTC_DRV_DS3232 is not set
# CONFIG_RTC_DRV_MAX6900 is not set
# CONFIG_RTC_DRV_RS5C372 is not set
# CONFIG_RTC_DRV_ISL1208 is not set
# CONFIG_RTC_DRV_ISL12022 is not set
# CONFIG_RTC_DRV_X1205 is not set
# CONFIG_RTC_DRV_PCF8523 is not set
# CONFIG_RTC_DRV_PCF8563 is not set
# CONFIG_RTC_DRV_PCF8583 is not set
# CONFIG_RTC_DRV_M41T80 is not set
# CONFIG_RTC_DRV_BQ32K is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
# CONFIG_RTC_DRV_RX8025 is not set
# CONFIG_RTC_DRV_EM3027 is not set
# CONFIG_RTC_DRV_RV3029C2 is not set
# CONFIG_RTC_DRV_PALMAS is not set

#
# SPI RTC drivers
#

#
# Platform RTC drivers
#
# CONFIG_RTC_DRV_CMOS is not set
# CONFIG_RTC_DRV_DS1286 is not set
# CONFIG_RTC_DRV_DS1511 is not set
# CONFIG_RTC_DRV_DS1553 is not set
# CONFIG_RTC_DRV_DS1742 is not set
# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_M48T35 is not set
# CONFIG_RTC_DRV_M48T59 is not set
# CONFIG_RTC_DRV_MSM6242 is not set
# CONFIG_RTC_DRV_BQ4802 is not set
# CONFIG_RTC_DRV_RP5C01 is not set
# CONFIG_RTC_DRV_V3020 is not set
# CONFIG_RTC_DRV_DS2404 is not set

#
# on-CPU RTC drivers
#
# CONFIG_RTC_DRV_SNVS is not set
CONFIG_DMADEVICES=y
# CONFIG_DMADEVICES_DEBUG is not set

#
# DMA Devices
#
# CONFIG_DW_DMAC is not set
# CONFIG_TIMB_DMA is not set
CONFIG_DMA_OMAP=y
CONFIG_DMA_ENGINE=y
CONFIG_DMA_VIRTUAL_CHANNELS=y

#
# DMA Clients
#
CONFIG_NET_DMA=y
CONFIG_ASYNC_TX_DMA=y
# CONFIG_DMATEST is not set
# CONFIG_AUXDISPLAY is not set
# CONFIG_UIO is not set
# CONFIG_VFIO is not set

#
# Virtio drivers
#
# CONFIG_VIRTIO_MMIO is not set

#
# Microsoft Hyper-V guest support
#
# CONFIG_STAGING is not set
CONFIG_CLKDEV_LOOKUP=y
CONFIG_HAVE_CLK_PREPARE=y
CONFIG_COMMON_CLK=y

#
# Common Clock Framework
#
# CONFIG_COMMON_CLK_DEBUG is not set
# CONFIG_CLK_TWL6040 is not set
# CONFIG_CLK_PALMAS is not set
CONFIG_HWSPINLOCK=y

#
# Hardware Spinlock drivers
#
CONFIG_HWSPINLOCK_OMAP=y
CONFIG_CLKSRC_MMIO=y
CONFIG_IOMMU_API=y
CONFIG_IOMMU_SUPPORT=y
CONFIG_OF_IOMMU=y
CONFIG_OMAP_IOMMU=y
CONFIG_OMAP_IOVMM=y
CONFIG_OMAP_IOMMU_DEBUG=y

#
# Remoteproc drivers (EXPERIMENTAL)
#
# CONFIG_STE_MODEM_RPROC is not set

#
# Rpmsg drivers (EXPERIMENTAL)
#
# CONFIG_VIRT_DRIVERS is not set
# CONFIG_PM_DEVFREQ is not set
# CONFIG_EXTCON is not set
# CONFIG_MEMORY is not set
# CONFIG_IIO is not set
# CONFIG_PWM is not set
# CONFIG_IPACK_BUS is not set

#
# File systems
#
CONFIG_DCACHE_WORD_ACCESS=y
# CONFIG_EXT2_FS is not set
# CONFIG_EXT3_FS is not set
CONFIG_EXT4_FS=y
CONFIG_EXT4_USE_FOR_EXT23=y
CONFIG_EXT4_FS_POSIX_ACL=y
# CONFIG_EXT4_FS_SECURITY is not set
# CONFIG_EXT4_DEBUG is not set
CONFIG_JBD2=y
# CONFIG_JBD2_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_BTRFS_FS is not set
# CONFIG_NILFS2_FS is not set
CONFIG_FS_POSIX_ACL=y
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_FANOTIFY is not set
CONFIG_QUOTA=y
# CONFIG_QUOTA_NETLINK_INTERFACE is not set
CONFIG_PRINT_QUOTA_WARNING=y
# CONFIG_QUOTA_DEBUG is not set
CONFIG_QUOTA_TREE=y
# CONFIG_QFMT_V1 is not set
CONFIG_QFMT_V2=y
CONFIG_QUOTACTL=y
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set

#
# Caches
#
# CONFIG_FSCACHE is not set

#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
# CONFIG_UDF_FS is not set

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
# CONFIG_NTFS_FS is not set

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_TMPFS_XATTR is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
# CONFIG_MISC_FILESYSTEMS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V2=y
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
# CONFIG_NFS_SWAP is not set
# CONFIG_NFS_V4_1 is not set
CONFIG_ROOT_NFS=y
# CONFIG_NFS_USE_LEGACY_DNS is not set
CONFIG_NFS_USE_KERNEL_DNS=y
# CONFIG_NFSD is not set
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_NFS_ACL_SUPPORT=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
# CONFIG_SUNRPC_DEBUG is not set
# CONFIG_CEPH_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ASCII is not set
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_MAC_ROMAN is not set
# CONFIG_NLS_MAC_CELTIC is not set
# CONFIG_NLS_MAC_CENTEURO is not set
# CONFIG_NLS_MAC_CROATIAN is not set
# CONFIG_NLS_MAC_CYRILLIC is not set
# CONFIG_NLS_MAC_GAELIC is not set
# CONFIG_NLS_MAC_GREEK is not set
# CONFIG_NLS_MAC_ICELAND is not set
# CONFIG_NLS_MAC_INUIT is not set
# CONFIG_NLS_MAC_ROMANIAN is not set
# CONFIG_NLS_MAC_TURKISH is not set
# CONFIG_NLS_UTF8 is not set

#
# Kernel hacking
#
CONFIG_PRINTK_TIME=y
CONFIG_DEFAULT_MESSAGE_LOGLEVEL=4
CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_READABLE_ASM is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_SECTION_MISMATCH is not set
CONFIG_IPIPE_DEBUG=y
# CONFIG_IPIPE_DEBUG_CONTEXT is not set
# CONFIG_IPIPE_DEBUG_INTERNAL is not set
CONFIG_IPIPE_TRACE=y
CONFIG_IPIPE_TRACE_ENABLE=y
CONFIG_IPIPE_TRACE_MCOUNT=y
CONFIG_IPIPE_TRACE_IRQSOFF=y
CONFIG_IPIPE_TRACE_SHIFT=14
CONFIG_IPIPE_TRACE_VMALLOC=y
CONFIG_IPIPE_TRACE_PANIC=y
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_LOCKUP_DETECTOR=y
# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
CONFIG_PANIC_ON_OOPS=y
CONFIG_PANIC_ON_OOPS_VALUE=1
CONFIG_DETECT_HUNG_TASK=y
CONFIG_DEFAULT_HUNG_TASK_TIMEOUT=120
# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
CONFIG_SCHED_DEBUG=y
CONFIG_SCHEDSTATS=y
CONFIG_TIMER_STATS=y
# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_SLUB_STATS is not set
CONFIG_HAVE_DEBUG_KMEMLEAK=y
# CONFIG_DEBUG_KMEMLEAK is not set
CONFIG_DEBUG_PREEMPT=y
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_PROVE_LOCKING is not set
CONFIG_PROVE_RCU_DELAY=y
# CONFIG_SPARSE_RCU_POINTER is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_ATOMIC_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
CONFIG_STACKTRACE=y
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_INFO_REDUCED is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_WRITECOUNT is not set
# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_TEST_LIST_SORT is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
# CONFIG_DEBUG_CREDENTIALS is not set
CONFIG_FRAME_POINTER=y
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_RCU_CPU_STALL_TIMEOUT=21
CONFIG_RCU_CPU_STALL_VERBOSE=y
# CONFIG_RCU_CPU_STALL_INFO is not set
# CONFIG_RCU_TRACE is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_DEBUG_PER_CPU_MAPS is not set
# CONFIG_LKDTM is not set
# CONFIG_NOTIFIER_ERROR_INJECTION is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_DEBUG_PAGEALLOC is not set
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_HAVE_C_RECORDMCOUNT=y
CONFIG_TRACE_CLOCK=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_EVENT_POWER_TRACING_DEPRECATED=y
CONFIG_CONTEXT_SWITCH_TRACER=y
CONFIG_TRACING=y
CONFIG_GENERIC_TRACER=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
CONFIG_FUNCTION_TRACER=y
CONFIG_FUNCTION_GRAPH_TRACER=y
# CONFIG_IRQSOFF_TRACER is not set
# CONFIG_PREEMPT_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_FTRACE_SYSCALLS is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
# CONFIG_PROFILE_ALL_BRANCHES is not set
# CONFIG_STACK_TRACER is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_PROBE_EVENTS is not set
# CONFIG_FUNCTION_PROFILER is not set
# CONFIG_FTRACE_STARTUP_TEST is not set
# CONFIG_RING_BUFFER_BENCHMARK is not set
# CONFIG_RBTREE_TEST is not set
# CONFIG_INTERVAL_TREE_TEST is not set
# CONFIG_DYNAMIC_DEBUG is not set
# CONFIG_DMA_API_DEBUG is not set
# CONFIG_ATOMIC64_SELFTEST is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
# CONFIG_TEST_KSTRTOX is not set
# CONFIG_STRICT_DEVMEM is not set
CONFIG_ARM_UNWIND=y
CONFIG_OLD_MCOUNT=y
CONFIG_DEBUG_USER=y
CONFIG_DEBUG_LL=y
CONFIG_DEBUG_LL_UART_NONE=y
# CONFIG_DEBUG_ICEDCC is not set
# CONFIG_DEBUG_SEMIHOSTING is not set
CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
CONFIG_EARLY_PRINTK=y
# CONFIG_PID_IN_CONTEXTIDR is not set

#
# Security options
#
CONFIG_KEYS=y
# CONFIG_ENCRYPTED_KEYS is not set
# CONFIG_KEYS_DEBUG_PROC_KEYS is not set
# CONFIG_SECURITY_DMESG_RESTRICT is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITYFS is not set
CONFIG_DEFAULT_SECURITY_DAC=y
CONFIG_DEFAULT_SECURITY=""
CONFIG_CRYPTO=y

#
# Crypto core or helper
#
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_HASH2=y
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_USER is not set
# CONFIG_CRYPTO_GF128MUL is not set
# CONFIG_CRYPTO_NULL is not set
# CONFIG_CRYPTO_PCRYPT is not set
# CONFIG_CRYPTO_CRYPTD is not set
# CONFIG_CRYPTO_AUTHENC is not set
# CONFIG_CRYPTO_TEST is not set

#
# Authenticated Encryption with Associated Data
#
# CONFIG_CRYPTO_CCM is not set
# CONFIG_CRYPTO_GCM is not set
# CONFIG_CRYPTO_SEQIV is not set

#
# Block modes
#
# CONFIG_CRYPTO_CBC is not set
# CONFIG_CRYPTO_CTR is not set
# CONFIG_CRYPTO_CTS is not set
# CONFIG_CRYPTO_ECB is not set
# CONFIG_CRYPTO_LRW is not set
# CONFIG_CRYPTO_PCBC is not set
# CONFIG_CRYPTO_XTS is not set

#
# Hash modes
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
# CONFIG_CRYPTO_VMAC is not set

#
# Digest
#
CONFIG_CRYPTO_CRC32C=y
# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_RMD128 is not set
# CONFIG_CRYPTO_RMD160 is not set
# CONFIG_CRYPTO_RMD256 is not set
# CONFIG_CRYPTO_RMD320 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA1_ARM is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_TGR192 is not set
# CONFIG_CRYPTO_WP512 is not set

#
# Ciphers
#
CONFIG_CRYPTO_AES=y
# CONFIG_CRYPTO_AES_ARM is not set
# CONFIG_CRYPTO_ANUBIS is not set
# CONFIG_CRYPTO_ARC4 is not set
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
# CONFIG_CRYPTO_DES is not set
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_SALSA20 is not set
# CONFIG_CRYPTO_SEED is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_TEA is not set
# CONFIG_CRYPTO_TWOFISH is not set

#
# Compression
#
# CONFIG_CRYPTO_DEFLATE is not set
# CONFIG_CRYPTO_ZLIB is not set
# CONFIG_CRYPTO_LZO is not set

#
# Random Number Generation
#
# CONFIG_CRYPTO_ANSI_CPRNG is not set
# CONFIG_CRYPTO_USER_API_HASH is not set
# CONFIG_CRYPTO_USER_API_SKCIPHER is not set
# CONFIG_CRYPTO_HW is not set
# CONFIG_ASYMMETRIC_KEY_TYPE is not set
CONFIG_BINARY_PRINTF=y

#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_GENERIC_STRNCPY_FROM_USER=y
CONFIG_GENERIC_STRNLEN_USER=y
CONFIG_GENERIC_PCI_IOMAP=y
CONFIG_GENERIC_IO=y
CONFIG_PERCPU_RWSEM=y
# CONFIG_CRC_CCITT is not set
CONFIG_CRC16=y
# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC32_SELFTEST is not set
CONFIG_CRC32_SLICEBY8=y
# CONFIG_CRC32_SLICEBY4 is not set
# CONFIG_CRC32_SARWATE is not set
# CONFIG_CRC32_BIT is not set
# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
# CONFIG_CRC8 is not set
CONFIG_LZO_COMPRESS=y
CONFIG_LZO_DECOMPRESS=y
# CONFIG_XZ_DEC is not set
# CONFIG_XZ_DEC_BCJ is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_CPU_RMAP=y
CONFIG_DQL=y
CONFIG_NLATTR=y
CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
# CONFIG_AVERAGE is not set
# CONFIG_CORDIC is not set
# CONFIG_DDR is not set

^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 21:06                     ` Gilles Chanteperdrix
@ 2014-03-31 21:25                       ` Lennart Sorensen
  2014-03-31 21:49                         ` Gilles Chanteperdrix
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-03-31 21:25 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Mon, Mar 31, 2014 at 11:06:51PM +0200, Gilles Chanteperdrix wrote:
> On 03/31/2014 10:57 PM, Lennart Sorensen wrote:
> > On Mon, Mar 31, 2014 at 04:53:39PM -0400, Lennart Sorensen wrote:
> >> [341548.649928] =================================
> >> [341548.649934] [ INFO: inconsistent lock state ]
> >> [341548.649943] 3.12-1-dra7xx #1 Not tainted
> >> [341548.649950] ---------------------------------
> >> [341548.649957] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
> 
> This looks fishy. It means that the root domain is not stalled while
> interrupt handler is called. This would need to be checked.
> 
> > No change in behaviour.  switchtest works, clocktest works, most other
> > things have illegal instruction.  Just waiting for the library and
> > runtime to recompile against 3.12's headers in case it matters.
> > After that it will be debug time.
> > 
> 
> Ok. You seem to have many debug options enabled. Please find attached
> the config I have used during my tests on omap5.

I will try and look through it and see which options to use.  This is
an omap57xx, not a 54xx, also known as the dra7xx.

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 21:25                       ` Lennart Sorensen
@ 2014-03-31 21:49                         ` Gilles Chanteperdrix
  2014-03-31 21:53                           ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-03-31 21:49 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 03/31/2014 11:25 PM, Lennart Sorensen wrote:
> On Mon, Mar 31, 2014 at 11:06:51PM +0200, Gilles Chanteperdrix wrote:
>> On 03/31/2014 10:57 PM, Lennart Sorensen wrote:
>>> On Mon, Mar 31, 2014 at 04:53:39PM -0400, Lennart Sorensen wrote:
>>>> [341548.649928] =================================
>>>> [341548.649934] [ INFO: inconsistent lock state ]
>>>> [341548.649943] 3.12-1-dra7xx #1 Not tainted
>>>> [341548.649950] ---------------------------------
>>>> [341548.649957] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
>>
>> This looks fishy. It means that the root domain is not stalled while
>> interrupt handler is called. This would need to be checked.
>>
>>> No change in behaviour.  switchtest works, clocktest works, most other
>>> things have illegal instruction.  Just waiting for the library and
>>> runtime to recompile against 3.12's headers in case it matters.
>>> After that it will be debug time.
>>>
>>
>> Ok. You seem to have many debug options enabled. Please find attached
>> the config I have used during my tests on omap5.
> 
> I will try and look through it and see which options to use.

Please post your .config, I will have a look. Please disable unlocked
context switch as well. Also please note that the context switch has
been reworked in 3.11, so you need Xenomai 2.6.x from the git repository.

>
>  This is
> an omap57xx, not a 54xx, also known as the dra7xx.
> 
a.k.a Vayu ?

I made quite a few other changes for omap5, I never merged them in the
I-pipe branch since the port was not finished. You may want to have a
look at them if you are continuing the work on omap5.

I have pushed the omap5-ipipe branch in ipipe-gch with this work in
progress.

-- 
                                                                Gilles.


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 21:49                         ` Gilles Chanteperdrix
@ 2014-03-31 21:53                           ` Lennart Sorensen
  2014-03-31 21:59                             ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-03-31 21:53 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Mon, Mar 31, 2014 at 11:49:02PM +0200, Gilles Chanteperdrix wrote:
> Please post your .config, I will have a look. Please disable unlocked
> context switch as well. Also please note that the context switch has
> been reworked in 3.11, so you need Xenomai 2.6.x from the git repository.

I am using the xenomai-2.6 git tree (current commit I see is as HEAD is
4081e1b032329bf0cc9442f466233d5fc1083fc5).

Doing a git pull I see I am 4 commits behind, and one does sound
interesting.  I will have to update that.

> a.k.a Vayu ?

Yes the circuit board does say VAYU EVM.

> I made quite a few other changes for omap5, I never merged them in the
> I-pipe branch since the port was not finished. You may want to have a
> look at them if you are continuing the work on omap5.

OK I will look at that too.

> I have pushed the omap5-ipipe branch in ipipe-gch with this work in
> progress.

OK, it looked quite promising on initial attemps, so it almost looked
like it might just work.

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 21:53                           ` Lennart Sorensen
@ 2014-03-31 21:59                             ` Lennart Sorensen
  2014-03-31 22:04                               ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-03-31 21:59 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Mon, Mar 31, 2014 at 05:53:48PM -0400, Lennart Sorensen wrote:
> I am using the xenomai-2.6 git tree (current commit I see is as HEAD is
> 4081e1b032329bf0cc9442f466233d5fc1083fc5).
> 
> Doing a git pull I see I am 4 commits behind, and one does sound
> interesting.  I will have to update that.

Hmm, the interesting patch does the same thing I already did myself to
get it to compile.  I guess that is OK then.

And I have attached by .config (I forgot last message).

-- 
Len Sorensen
-------------- next part --------------
#
# Automatically generated file; DO NOT EDIT.
# Linux/arm 3.12.14 Kernel Configuration
#
CONFIG_ARM=y
CONFIG_IPIPE_WANT_ACTIVE_MM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_HAVE_PROC_CPU=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_ARCH_HAS_CPUFREQ=y
CONFIG_ARCH_HAS_BANDGAP=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_DMA_NONCOHERENT=y
CONFIG_NEED_DMA_MAP_STATE=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_ARM_PATCH_PHYS_VIRT=y
CONFIG_GENERIC_BUG=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
CONFIG_IRQ_WORK=y
CONFIG_BUILDTIME_EXTABLE_SORT=y

#
# General setup
#
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_CROSS_COMPILE=""
# CONFIG_COMPILE_TEST is not set
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_HAVE_KERNEL_GZIP=y
CONFIG_HAVE_KERNEL_LZMA=y
CONFIG_HAVE_KERNEL_XZ=y
CONFIG_HAVE_KERNEL_LZO=y
CONFIG_HAVE_KERNEL_LZ4=y
CONFIG_KERNEL_GZIP=y
# CONFIG_KERNEL_LZMA is not set
# CONFIG_KERNEL_XZ is not set
# CONFIG_KERNEL_LZO is not set
# CONFIG_KERNEL_LZ4 is not set
CONFIG_DEFAULT_HOSTNAME="(none)"
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
CONFIG_POSIX_MQUEUE_SYSCTL=y
# CONFIG_FHANDLE is not set
# CONFIG_AUDIT is not set

#
# IRQ subsystem
#
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_IRQ_SHOW=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_CHIP=y
CONFIG_IRQ_DOMAIN=y
# CONFIG_IRQ_DOMAIN_DEBUG is not set
CONFIG_IRQ_FORCED_THREADING=y
CONFIG_SPARSE_IRQ=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_KTIME_SCALAR=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_ARCH_HAS_TICK_BROADCAST=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y

#
# Timers subsystem
#
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ_COMMON=y
# CONFIG_HZ_PERIODIC is not set
CONFIG_NO_HZ_IDLE=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y

#
# CPU/Task time and stats accounting
#
CONFIG_TICK_CPU_ACCOUNTING=y
# CONFIG_IRQ_TIME_ACCOUNTING is not set
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set

#
# RCU Subsystem
#
CONFIG_TREE_PREEMPT_RCU=y
CONFIG_PREEMPT_RCU=y
CONFIG_RCU_STALL_COMMON=y
# CONFIG_RCU_USER_QS is not set
CONFIG_RCU_FANOUT=32
CONFIG_RCU_FANOUT_LEAF=16
# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_RCU_FAST_NO_HZ is not set
# CONFIG_TREE_RCU_TRACE is not set
# CONFIG_RCU_BOOST is not set
# CONFIG_RCU_NOCB_CPU is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=16
CONFIG_GENERIC_SCHED_CLOCK=y
# CONFIG_CGROUPS is not set
# CONFIG_CHECKPOINT_RESTORE is not set
CONFIG_NAMESPACES=y
CONFIG_UTS_NS=y
CONFIG_IPC_NS=y
# CONFIG_USER_NS is not set
CONFIG_PID_NS=y
CONFIG_NET_NS=y
# CONFIG_UIDGID_STRICT_TYPE_CHECKS is not set
# CONFIG_SCHED_AUTOGROUP is not set
# CONFIG_SYSFS_DEPRECATED is not set
# CONFIG_RELAY is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_RD_GZIP=y
# CONFIG_RD_BZIP2 is not set
# CONFIG_RD_LZMA is not set
# CONFIG_RD_XZ is not set
# CONFIG_RD_LZO is not set
# CONFIG_RD_LZ4 is not set
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_ANON_INODES=y
CONFIG_HAVE_UID16=y
CONFIG_EXPERT=y
CONFIG_UID16=y
# CONFIG_SYSCTL_SYSCALL is not set
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
CONFIG_PCI_QUIRKS=y
# CONFIG_EMBEDDED is not set
CONFIG_HAVE_PERF_EVENTS=y
CONFIG_PERF_USE_VMALLOC=y

#
# Kernel Performance Events And Counters
#
CONFIG_PERF_EVENTS=y
# CONFIG_DEBUG_PERF_USE_VMALLOC is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLUB_DEBUG=y
# CONFIG_COMPAT_BRK is not set
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
CONFIG_SLUB_CPU_PARTIAL=y
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
CONFIG_KPROBES=y
CONFIG_JUMP_LABEL=y
# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
CONFIG_KRETPROBES=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_DMA_ATTRS=y
CONFIG_HAVE_DMA_CONTIGUOUS=y
CONFIG_USE_GENERIC_SMP_HELPERS=y
CONFIG_GENERIC_SMP_IDLE_THREAD=y
CONFIG_GENERIC_IDLE_POLL_SETUP=y
CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
CONFIG_HAVE_HW_BREAKPOINT=y
CONFIG_HAVE_ARCH_JUMP_LABEL=y
CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
CONFIG_HAVE_CONTEXT_TRACKING=y
CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
CONFIG_MODULES_USE_ELF_REL=y
CONFIG_CLONE_BACKWARDS=y
CONFIG_OLD_SIGSUSPEND3=y
CONFIG_OLD_SIGACTION=y

#
# GCOV-based kernel profiling
#
# CONFIG_GCOV_KERNEL is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_FORCE_LOAD=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
# CONFIG_MODULE_SIG is not set
CONFIG_STOP_MACHINE=y
CONFIG_BLOCK=y
CONFIG_LBDAF=y
CONFIG_BLK_DEV_BSG=y
# CONFIG_BLK_DEV_BSGLIB is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_BLK_CMDLINE_PARSER is not set

#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_AIX_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
# CONFIG_MAC_PARTITION is not set
CONFIG_MSDOS_PARTITION=y
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
# CONFIG_LDM_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
CONFIG_EFI_PARTITION=y
# CONFIG_SYSV68_PARTITION is not set
# CONFIG_CMDLINE_PARTITION is not set

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
CONFIG_PADATA=y
CONFIG_UNINLINE_SPIN_UNLOCK=y

#
# Real-time sub-system
#
CONFIG_XENOMAI=y
CONFIG_XENO_GENERIC_STACKPOOL=y
CONFIG_XENO_FASTSYNCH_DEP=y
CONFIG_XENO_FASTSYNCH=y
CONFIG_XENO_OPT_NUCLEUS=m
CONFIG_XENO_OPT_PERVASIVE=y
# CONFIG_XENO_OPT_PRIOCPL is not set
CONFIG_XENO_OPT_PIPELINE_HEAD=y
# CONFIG_XENO_OPT_SCHED_CLASSES is not set
CONFIG_XENO_OPT_PIPE=y
CONFIG_XENO_OPT_MAP=y
CONFIG_XENO_OPT_VFILE=y
CONFIG_XENO_OPT_PIPE_NRDEV=32
CONFIG_XENO_OPT_REGISTRY_NRSLOTS=512
CONFIG_XENO_OPT_SYS_HEAPSZ=256
CONFIG_XENO_OPT_SYS_STACKPOOLSZ=128
CONFIG_XENO_OPT_SEM_HEAPSZ=12
CONFIG_XENO_OPT_GLOBAL_SEM_HEAPSZ=12
CONFIG_XENO_OPT_STATS=y
CONFIG_XENO_OPT_DEBUG=y
# CONFIG_XENO_OPT_DEBUG_NUCLEUS is not set
CONFIG_XENO_OPT_DEBUG_XNLOCK=y
# CONFIG_XENO_OPT_DEBUG_QUEUES is not set
# CONFIG_XENO_OPT_DEBUG_REGISTRY is not set
# CONFIG_XENO_OPT_DEBUG_TIMERS is not set
CONFIG_XENO_OPT_DEBUG_SYNCH_RELAX=y
CONFIG_XENO_OPT_WATCHDOG=y
CONFIG_XENO_OPT_WATCHDOG_TIMEOUT=4
# CONFIG_XENO_OPT_SHIRQ is not set
CONFIG_XENO_OPT_SELECT=y
CONFIG_XENO_OPT_HOSTRT=y

#
# Timing
#
# CONFIG_XENO_OPT_TIMING_PERIODIC is not set
CONFIG_XENO_OPT_TIMING_VIRTICK=1000
CONFIG_XENO_OPT_TIMING_SCHEDLAT=0

#
# Scalability
#
# CONFIG_XENO_OPT_SCALABLE_SCHED is not set
CONFIG_XENO_OPT_TIMER_LIST=y
# CONFIG_XENO_OPT_TIMER_HEAP is not set
# CONFIG_XENO_OPT_TIMER_WHEEL is not set

#
# Machine
#
CONFIG_IPIPE_WANT_PREEMPTIBLE_SWITCH=y
CONFIG_XENO_HW_FPU=y
CONFIG_XENO_HW_UNLOCKED_SWITCH=y

#
# Interfaces
#
CONFIG_XENO_SKIN_NATIVE=m
CONFIG_XENO_OPT_NATIVE_PERIOD=0
CONFIG_XENO_OPT_NATIVE_PIPE=y
CONFIG_XENO_OPT_NATIVE_PIPE_BUFSZ=1024
CONFIG_XENO_OPT_NATIVE_SEM=y
CONFIG_XENO_OPT_NATIVE_EVENT=y
CONFIG_XENO_OPT_NATIVE_MUTEX=y
CONFIG_XENO_OPT_NATIVE_COND=y
CONFIG_XENO_OPT_NATIVE_QUEUE=y
CONFIG_XENO_OPT_NATIVE_BUFFER=y
CONFIG_XENO_OPT_NATIVE_HEAP=y
CONFIG_XENO_OPT_NATIVE_ALARM=y
CONFIG_XENO_OPT_NATIVE_MPS=y
# CONFIG_XENO_OPT_NATIVE_INTR is not set
CONFIG_XENO_OPT_DEBUG_NATIVE=y
CONFIG_XENO_SKIN_POSIX=m
CONFIG_XENO_OPT_POSIX_PERIOD=0
CONFIG_XENO_OPT_POSIX_REGISTRY_NRSLOTS=64
CONFIG_XENO_OPT_POSIX_REGISTRY_NRDESCS=128
CONFIG_XENO_OPT_POSIX_NRTIMERS=128
# CONFIG_XENO_OPT_POSIX_SHM is not set
# CONFIG_XENO_OPT_POSIX_INTR is not set
CONFIG_XENO_OPT_POSIX_SELECT=y
CONFIG_XENO_OPT_DEBUG_POSIX=y
# CONFIG_XENO_SKIN_PSOS is not set
# CONFIG_XENO_SKIN_UITRON is not set
# CONFIG_XENO_SKIN_VRTX is not set
# CONFIG_XENO_SKIN_VXWORKS is not set
# CONFIG_XENO_OPT_NOWARN_DEPRECATED is not set
CONFIG_XENO_SKIN_RTDM=m
CONFIG_XENO_OPT_RTDM_PERIOD=0
CONFIG_XENO_OPT_RTDM_FILDES=128
CONFIG_XENO_OPT_RTDM_SELECT=y
# CONFIG_XENO_OPT_DEBUG_RTDM is not set
CONFIG_XENO_OPT_DEBUG_RTDM_APPL=y

#
# Drivers
#

#
# Serial drivers
#
# CONFIG_XENO_DRIVERS_16550A is not set

#
# Testing drivers
#
CONFIG_XENO_DRIVERS_TIMERBENCH=m
# CONFIG_XENO_DRIVERS_KLATENCY is not set
# CONFIG_XENO_DRIVERS_IRQBENCH is not set
CONFIG_XENO_DRIVERS_SWITCHTEST=m
# CONFIG_XENO_DRIVERS_RTDMTEST is not set

#
# CAN drivers
#
# CONFIG_XENO_DRIVERS_CAN is not set

#
# ANALOGY drivers
#
# CONFIG_XENO_DRIVERS_ANALOGY is not set

#
# Real-time IPC drivers
#
CONFIG_XENO_DRIVERS_RTIPC=m
CONFIG_XENO_DRIVERS_RTIPC_XDDP=y
CONFIG_XENO_DRIVERS_RTIPC_IDDP=y
CONFIG_XENO_OPT_IDDP_NRPORT=32
CONFIG_XENO_DRIVERS_RTIPC_BUFP=y
CONFIG_XENO_OPT_BUFP_NRPORT=32
CONFIG_FREEZER=y

#
# System Type
#
CONFIG_MMU=y
# CONFIG_ARCH_MULTIPLATFORM is not set
# CONFIG_ARCH_INTEGRATOR is not set
# CONFIG_ARCH_REALVIEW is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_AT91 is not set
# CONFIG_ARCH_CLPS711X is not set
# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IOP32X is not set
# CONFIG_ARCH_IOP33X is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_DOVE is not set
# CONFIG_ARCH_KIRKWOOD is not set
# CONFIG_ARCH_MV78XX0 is not set
# CONFIG_ARCH_ORION5X is not set
# CONFIG_ARCH_MMP is not set
# CONFIG_ARCH_KS8695 is not set
# CONFIG_ARCH_W90X900 is not set
# CONFIG_ARCH_LPC32XX is not set
# CONFIG_ARCH_PXA is not set
# CONFIG_ARCH_MSM is not set
# CONFIG_ARCH_SHMOBILE is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C24XX is not set
# CONFIG_ARCH_S3C64XX is not set
# CONFIG_ARCH_S5P64X0 is not set
# CONFIG_ARCH_S5PC100 is not set
# CONFIG_ARCH_S5PV210 is not set
# CONFIG_ARCH_EXYNOS is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_DAVINCI is not set
# CONFIG_ARCH_OMAP1 is not set
CONFIG_ARCH_OMAP2PLUS=y

#
# Multiple platform selection
#

#
# CPU Core family selection
#
# CONFIG_ARCH_MULTI_V6 is not set
CONFIG_ARCH_MULTI_V7=y
CONFIG_ARCH_MULTI_V6_V7=y
# CONFIG_ARCH_MULTI_CPU_AUTO is not set
# CONFIG_ARCH_MVEBU is not set
# CONFIG_ARCH_BCM is not set
CONFIG_GPIO_PCA953X=y
# CONFIG_ARCH_HIGHBANK is not set
# CONFIG_ARCH_KEYSTONE is not set
# CONFIG_ARCH_MXC is not set

#
# TI OMAP Common Features
#

#
# OMAP Feature Selections
#
CONFIG_OMAP_RESET_CLOCKS=y
CONFIG_OMAP_MUX=y
CONFIG_OMAP_MUX_DEBUG=y
CONFIG_OMAP_MUX_WARNINGS=y
CONFIG_OMAP_32K_TIMER=y
# CONFIG_OMAP3_L2_AUX_SECURE_SAVE_RESTORE is not set
CONFIG_OMAP_DM_TIMER=y
CONFIG_OMAP_PM_NOOP=y
CONFIG_MACH_OMAP_GENERIC=y
CONFIG_ARCH_OMAP=y
CONFIG_ARCH_OMAP3=y
CONFIG_ARCH_OMAP4=y
CONFIG_SOC_OMAP5=y
CONFIG_SOC_AM33XX=y
CONFIG_SOC_AM43XX=y

#
# TI OMAP2/3/4 Specific Features
#
CONFIG_ARCH_OMAP2PLUS_TYPICAL=y
CONFIG_SOC_HAS_OMAP2_SDRC=y
CONFIG_SOC_HAS_REALTIME_COUNTER=y
CONFIG_SOC_DRA7XX=y
# CONFIG_SOC_OMAP3430 is not set
# CONFIG_SOC_TI81XX is not set

#
# OMAP Board Type
#
# CONFIG_MACH_OMAP3_BEAGLE is not set
# CONFIG_MACH_DEVKIT8000 is not set
# CONFIG_MACH_OMAP_LDP is not set
# CONFIG_MACH_OMAP3530_LV_SOM is not set
# CONFIG_MACH_OMAP3_TORPEDO is not set
# CONFIG_MACH_OVERO is not set
# CONFIG_MACH_OMAP3EVM is not set
# CONFIG_MACH_OMAP3517EVM is not set
# CONFIG_MACH_CRANEBOARD is not set
# CONFIG_MACH_OMAP3_PANDORA is not set
# CONFIG_MACH_TOUCHBOOK is not set
# CONFIG_MACH_OMAP_3430SDP is not set
# CONFIG_MACH_NOKIA_RM680 is not set
# CONFIG_MACH_NOKIA_RX51 is not set
# CONFIG_MACH_OMAP_ZOOM2 is not set
# CONFIG_MACH_OMAP_ZOOM3 is not set
# CONFIG_MACH_CM_T35 is not set
# CONFIG_MACH_CM_T3517 is not set
# CONFIG_MACH_IGEP0020 is not set
# CONFIG_MACH_IGEP0030 is not set
# CONFIG_MACH_SBC3530 is not set
# CONFIG_MACH_OMAP_3630SDP is not set
# CONFIG_OMAP3_EMU is not set
# CONFIG_OMAP3_SDRC_AC_TIMING is not set
# CONFIG_OMAP4_ERRATA_I688 is not set
# CONFIG_ARCH_ROCKCHIP is not set
# CONFIG_ARCH_SOCFPGA is not set
# CONFIG_PLAT_SPEAR is not set
# CONFIG_ARCH_STI is not set
# CONFIG_ARCH_SHMOBILE_MULTI is not set
# CONFIG_ARCH_SUNXI is not set
# CONFIG_ARCH_SIRF is not set
# CONFIG_ARCH_TEGRA is not set
# CONFIG_ARCH_U8500 is not set
# CONFIG_ARCH_VEXPRESS is not set
# CONFIG_ARCH_VIRT is not set
# CONFIG_ARCH_WM8850 is not set
# CONFIG_ARCH_ZYNQ is not set
CONFIG_IPIPE_ARM_KUSER_TSC=y

#
# Processor Type
#
CONFIG_CPU_V7=y
CONFIG_CPU_32v6K=y
CONFIG_CPU_32v7=y
CONFIG_CPU_ABRT_EV7=y
CONFIG_CPU_PABRT_V7=y
CONFIG_CPU_CACHE_V7=y
CONFIG_CPU_CACHE_VIPT=y
CONFIG_CPU_COPY_V6=y
CONFIG_CPU_TLB_V7=y
CONFIG_CPU_HAS_ASID=y
CONFIG_CPU_CP15=y
CONFIG_CPU_CP15_MMU=y

#
# Processor Features
#
# CONFIG_ARM_LPAE is not set
# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
CONFIG_ARM_THUMB=y
CONFIG_ARM_THUMBEE=y
CONFIG_ARM_VIRT_EXT=y
CONFIG_SWP_EMULATE=y
# CONFIG_CPU_ICACHE_DISABLE is not set
# CONFIG_CPU_DCACHE_DISABLE is not set
# CONFIG_CPU_BPREDICT_DISABLE is not set
CONFIG_NEED_KUSER_HELPERS=y
CONFIG_KUSER_HELPERS=y
CONFIG_OUTER_CACHE=y
CONFIG_OUTER_CACHE_SYNC=y
CONFIG_MIGHT_HAVE_CACHE_L2X0=y
CONFIG_CACHE_L2X0=y
CONFIG_CACHE_PL310=y
CONFIG_ARM_L1_CACHE_SHIFT_6=y
CONFIG_ARM_L1_CACHE_SHIFT=6
CONFIG_ARM_DMA_MEM_BUFFERABLE=y
CONFIG_ARM_NR_BANKS=8
CONFIG_MULTI_IRQ_HANDLER=y
# CONFIG_ARM_ERRATA_430973 is not set
# CONFIG_ARM_ERRATA_458693 is not set
# CONFIG_ARM_ERRATA_460075 is not set
# CONFIG_ARM_ERRATA_742230 is not set
# CONFIG_ARM_ERRATA_742231 is not set
CONFIG_PL310_ERRATA_588369=y
# CONFIG_ARM_ERRATA_643719 is not set
CONFIG_ARM_ERRATA_720789=y
CONFIG_PL310_ERRATA_727915=y
# CONFIG_ARM_ERRATA_743622 is not set
# CONFIG_ARM_ERRATA_751472 is not set
CONFIG_PL310_ERRATA_753970=y
CONFIG_ARM_ERRATA_754322=y
# CONFIG_ARM_ERRATA_754327 is not set
# CONFIG_ARM_ERRATA_764369 is not set
CONFIG_PL310_ERRATA_769419=y
CONFIG_ARM_ERRATA_775420=y
CONFIG_ARM_ERRATA_798181=y
CONFIG_ARM_ERRATA_773022=y
CONFIG_ARM_ERRATA_799270=y
CONFIG_TI_PRIV_EDMA=y

#
# Bus support
#
CONFIG_PCI=y
CONFIG_PCI_SYSCALL=y
CONFIG_PCI_MSI=y
# CONFIG_PCI_DEBUG is not set
# CONFIG_PCI_REALLOC_ENABLE_AUTO is not set
# CONFIG_PCI_STUB is not set
# CONFIG_PCI_IOV is not set
# CONFIG_PCI_PRI is not set
# CONFIG_PCI_PASID is not set

#
# PCI host controller drivers
#
CONFIG_PCIE_DRA7XX=y
CONFIG_PCIE_DW=y
CONFIG_PCIEPORTBUS=y
CONFIG_PCIEAER=y
# CONFIG_PCIE_ECRC is not set
# CONFIG_PCIEAER_INJECT is not set
CONFIG_PCIEASPM=y
# CONFIG_PCIEASPM_DEBUG is not set
CONFIG_PCIEASPM_DEFAULT=y
# CONFIG_PCIEASPM_POWERSAVE is not set
# CONFIG_PCIEASPM_PERFORMANCE is not set
CONFIG_PCIE_PME=y
# CONFIG_PCCARD is not set

#
# Kernel Features
#
CONFIG_HAVE_SMP=y
CONFIG_SMP=y
CONFIG_SMP_ON_UP=y
CONFIG_ARM_CPU_TOPOLOGY=y
# CONFIG_SCHED_MC is not set
# CONFIG_SCHED_SMT is not set
CONFIG_HAVE_ARM_SCU=y
CONFIG_HAVE_ARM_ARCH_TIMER=y
CONFIG_HAVE_ARM_TWD=y
# CONFIG_MCPM is not set
CONFIG_VMSPLIT_3G=y
# CONFIG_VMSPLIT_2G is not set
# CONFIG_VMSPLIT_1G is not set
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_NR_CPUS=2
CONFIG_HOTPLUG_CPU=y
# CONFIG_ARM_PSCI is not set
CONFIG_ARCH_NR_GPIO=512
CONFIG_IPIPE=y
CONFIG_IPIPE_LEGACY=y
CONFIG_IPIPE_CORE=y
CONFIG_IPIPE_CORE_APIREV=2
CONFIG_IPIPE_WANT_APIREV_2=y
CONFIG_IPIPE_TARGET_APIREV=2
CONFIG_IPIPE_HAVE_HOSTRT=y
CONFIG_IPIPE_DELAYED_ATOMICSW=y
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_PREEMPT_COUNT=y
CONFIG_HZ_FIXED=0
# CONFIG_HZ_100 is not set
# CONFIG_HZ_200 is not set
# CONFIG_HZ_250 is not set
# CONFIG_HZ_300 is not set
# CONFIG_HZ_500 is not set
CONFIG_HZ_1000=y
CONFIG_HZ=1000
CONFIG_SCHED_HRTICK=y
# CONFIG_THUMB2_KERNEL is not set
CONFIG_AEABI=y
# CONFIG_OABI_COMPAT is not set
CONFIG_ARCH_HAS_HOLES_MEMORYMODEL=y
# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
CONFIG_HAVE_ARCH_PFN_VALID=y
CONFIG_HIGHMEM=y
# CONFIG_HIGHPTE is not set
CONFIG_HW_PERF_EVENTS=y
CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_HAVE_MEMBLOCK=y
# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=999999
CONFIG_COMPACTION=y
CONFIG_MIGRATION=y
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_BOUNCE=y
# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_CROSS_MEMORY_ATTACH=y
# CONFIG_CLEANCACHE is not set
# CONFIG_FRONTSWAP is not set
# CONFIG_CMA is not set
# CONFIG_ZBUD is not set
CONFIG_FORCE_MAX_ZONEORDER=12
CONFIG_ALIGNMENT_TRAP=y
# CONFIG_UACCESS_WITH_MEMCPY is not set
# CONFIG_SECCOMP is not set
# CONFIG_CC_STACKPROTECTOR is not set
# CONFIG_XEN is not set

#
# Boot options
#
CONFIG_USE_OF=y
CONFIG_ATAGS=y
# CONFIG_DEPRECATED_PARAM_STRUCT is not set
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
# CONFIG_ARM_APPENDED_DTB is not set
CONFIG_CMDLINE="root=/dev/mmcblk0p2 rootwait console=ttyO0,115200"
CONFIG_CMDLINE_FROM_BOOTLOADER=y
# CONFIG_CMDLINE_EXTEND is not set
# CONFIG_CMDLINE_FORCE is not set
# CONFIG_XIP_KERNEL is not set
# CONFIG_KEXEC is not set
# CONFIG_CRASH_DUMP is not set
CONFIG_AUTO_ZRELADDR=y

#
# CPU Power Management
#

#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set

#
# CPU Idle
#
CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED=y

#
# Floating point emulation
#

#
# At least one emulation must be selected
#
CONFIG_VFP=y
CONFIG_VFPv3=y
CONFIG_NEON=y
CONFIG_KERNEL_MODE_NEON=y

#
# Userspace binary formats
#
CONFIG_BINFMT_ELF=y
CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS=y
CONFIG_BINFMT_SCRIPT=y
# CONFIG_HAVE_AOUT is not set
CONFIG_BINFMT_MISC=y
CONFIG_COREDUMP=y

#
# Power management options
#
CONFIG_SUSPEND=y
CONFIG_SUSPEND_FREEZER=y
CONFIG_PM_SLEEP=y
CONFIG_PM_SLEEP_SMP=y
# CONFIG_PM_AUTOSLEEP is not set
# CONFIG_PM_WAKELOCKS is not set
CONFIG_PM_RUNTIME=y
CONFIG_PM=y
CONFIG_PM_DEBUG=y
# CONFIG_PM_ADVANCED_DEBUG is not set
# CONFIG_PM_TEST_SUSPEND is not set
CONFIG_PM_SLEEP_DEBUG=y
# CONFIG_APM_EMULATION is not set
CONFIG_ARCH_HAS_OPP=y
CONFIG_PM_OPP=y
CONFIG_PM_CLK=y
# CONFIG_WQ_POWER_EFFICIENT_DEFAULT is not set
CONFIG_CPU_PM=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_ARM_CPU_SUSPEND=y
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_DIAG is not set
CONFIG_UNIX=y
# CONFIG_UNIX_DIAG is not set
CONFIG_XFRM=y
CONFIG_XFRM_ALGO=y
CONFIG_XFRM_USER=y
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_XFRM_MIGRATE=y
# CONFIG_XFRM_STATISTICS is not set
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
# CONFIG_MPLS is not set
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
# CONFIG_IP_FIB_TRIE_STATS is not set
# CONFIG_IP_MULTIPLE_TABLES is not set
# CONFIG_IP_ROUTE_MULTIPATH is not set
# CONFIG_IP_ROUTE_VERBOSE is not set
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE_DEMUX is not set
CONFIG_NET_IP_TUNNEL=m
# CONFIG_IP_MROUTE is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_NET_IPVTI is not set
CONFIG_INET_AH=m
CONFIG_INET_ESP=m
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_XFRM_TUNNEL is not set
CONFIG_INET_TUNNEL=m
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_INET_XFRM_MODE_BEET=m
CONFIG_INET_LRO=m
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_INET_UDP_DIAG is not set
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
CONFIG_IPV6=m
# CONFIG_IPV6_PRIVACY is not set
# CONFIG_IPV6_ROUTER_PREF is not set
# CONFIG_IPV6_OPTIMISTIC_DAD is not set
# CONFIG_INET6_AH is not set
# CONFIG_INET6_ESP is not set
# CONFIG_INET6_IPCOMP is not set
# CONFIG_IPV6_MIP6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
CONFIG_INET6_XFRM_MODE_TRANSPORT=m
CONFIG_INET6_XFRM_MODE_TUNNEL=m
CONFIG_INET6_XFRM_MODE_BEET=m
# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
CONFIG_IPV6_SIT=m
# CONFIG_IPV6_SIT_6RD is not set
CONFIG_IPV6_NDISC_NODETYPE=y
# CONFIG_IPV6_TUNNEL is not set
# CONFIG_IPV6_GRE is not set
# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_IPV6_MROUTE is not set
# CONFIG_NETLABEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETWORK_PHY_TIMESTAMPING is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_NETFILTER_ADVANCED=y

#
# Core Netfilter Configuration
#
# CONFIG_NETFILTER_NETLINK_ACCT is not set
# CONFIG_NETFILTER_NETLINK_QUEUE is not set
# CONFIG_NETFILTER_NETLINK_LOG is not set
# CONFIG_NF_CONNTRACK is not set
# CONFIG_NETFILTER_XTABLES is not set
# CONFIG_IP_VS is not set

#
# IP: Netfilter Configuration
#
# CONFIG_NF_DEFRAG_IPV4 is not set
# CONFIG_IP_NF_IPTABLES is not set
# CONFIG_IP_NF_ARPTABLES is not set

#
# IPv6: Netfilter Configuration
#
# CONFIG_NF_DEFRAG_IPV6 is not set
# CONFIG_IP6_NF_IPTABLES is not set
# CONFIG_IP_DCCP is not set
CONFIG_IP_SCTP=m
CONFIG_NET_SCTPPROBE=m
# CONFIG_SCTP_DBG_OBJCNT is not set
CONFIG_SCTP_DEFAULT_COOKIE_HMAC_MD5=y
# CONFIG_SCTP_DEFAULT_COOKIE_HMAC_SHA1 is not set
# CONFIG_SCTP_DEFAULT_COOKIE_HMAC_NONE is not set
CONFIG_SCTP_COOKIE_HMAC_MD5=y
CONFIG_SCTP_COOKIE_HMAC_SHA1=y
# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_L2TP is not set
# CONFIG_BRIDGE is not set
CONFIG_HAVE_NET_DSA=y
CONFIG_VLAN_8021Q=m
# CONFIG_VLAN_8021Q_GVRP is not set
# CONFIG_VLAN_8021Q_MVRP is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_PHONET is not set
# CONFIG_IEEE802154 is not set
# CONFIG_NET_SCHED is not set
# CONFIG_DCB is not set
CONFIG_DNS_RESOLVER=y
# CONFIG_BATMAN_ADV is not set
# CONFIG_OPENVSWITCH is not set
# CONFIG_VSOCKETS is not set
# CONFIG_NETLINK_MMAP is not set
CONFIG_NETLINK_DIAG=y
CONFIG_NET_MPLS_GSO=m
CONFIG_RPS=y
CONFIG_RFS_ACCEL=y
CONFIG_XPS=y
CONFIG_NET_RX_BUSY_POLL=y
CONFIG_BQL=y
# CONFIG_BPF_JIT is not set
CONFIG_NET_FLOW_LIMIT=y

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NET_TCPPROBE is not set
# CONFIG_NET_DROP_MONITOR is not set
# CONFIG_HAMRADIO is not set
# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
# CONFIG_LIB80211 is not set

#
# CFG80211 needs to be enabled for MAC80211
#
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_RFKILL_REGULATOR is not set
# CONFIG_NET_9P is not set
# CONFIG_CAIF is not set
# CONFIG_CEPH_LIB is not set
# CONFIG_NFC is not set
CONFIG_HAVE_BPF_JIT=y

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_DEVTMPFS=y
CONFIG_DEVTMPFS_MOUNT=y
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
CONFIG_FIRMWARE_IN_KERNEL=y
CONFIG_EXTRA_FIRMWARE=""
CONFIG_FW_LOADER_USER_HELPER=y
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_GENERIC_CPU_DEVICES is not set
CONFIG_SOC_BUS=y
CONFIG_REGMAP=y
CONFIG_REGMAP_I2C=y
CONFIG_REGMAP_MMIO=y
CONFIG_REGMAP_IRQ=y
# CONFIG_DMA_SHARED_BUFFER is not set

#
# Bus devices
#
CONFIG_OMAP_OCP2SCP=y
CONFIG_OMAP_INTERCONNECT=y
CONFIG_ARM_CCI=y
CONFIG_CONNECTOR=y
CONFIG_PROC_EVENTS=y
CONFIG_MTD=y
# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AFS_PARTS is not set
CONFIG_MTD_OF_PARTS=y
# CONFIG_MTD_AR7_PARTS is not set

#
# User Modules And Translation Layers
#
CONFIG_MTD_BLKDEVS=y
CONFIG_MTD_BLOCK=y
# CONFIG_FTL is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
# CONFIG_SSFDC is not set
# CONFIG_SM_FTL is not set
CONFIG_MTD_OOPS=y
# CONFIG_MTD_SWAP is not set

#
# RAM/ROM/Flash chip drivers
#
CONFIG_MTD_CFI=y
# CONFIG_MTD_JEDECPROBE is not set
CONFIG_MTD_GEN_PROBE=y
# CONFIG_MTD_CFI_ADV_OPTIONS is not set
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
CONFIG_MTD_CFI_INTELEXT=y
# CONFIG_MTD_CFI_AMDSTD is not set
# CONFIG_MTD_CFI_STAA is not set
CONFIG_MTD_CFI_UTIL=y
# CONFIG_MTD_RAM is not set
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set

#
# Mapping drivers for chip access
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
# CONFIG_MTD_PHYSMAP is not set
# CONFIG_MTD_PHYSMAP_OF is not set
# CONFIG_MTD_INTEL_VR_NOR is not set
# CONFIG_MTD_PLATRAM is not set

#
# Self-contained MTD device drivers
#
# CONFIG_MTD_PMC551 is not set
# CONFIG_MTD_DATAFLASH is not set
CONFIG_MTD_M25P80=y
# CONFIG_MTD_SST25L is not set
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
# CONFIG_MTD_BLOCK2MTD is not set

#
# Disk-On-Chip Device Drivers
#
# CONFIG_MTD_DOCG3 is not set
CONFIG_MTD_NAND_ECC=y
# CONFIG_MTD_NAND_ECC_SMC is not set
CONFIG_MTD_NAND=y
# CONFIG_MTD_NAND_ECC_BCH is not set
# CONFIG_MTD_SM_COMMON is not set
# CONFIG_MTD_NAND_DENALI is not set
# CONFIG_MTD_NAND_GPIO is not set
CONFIG_MTD_NAND_OMAP2=y
# CONFIG_MTD_NAND_OMAP_BCH is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_RICOH is not set
# CONFIG_MTD_NAND_DISKONCHIP is not set
# CONFIG_MTD_NAND_DOCG4 is not set
# CONFIG_MTD_NAND_CAFE is not set
# CONFIG_MTD_NAND_NANDSIM is not set
# CONFIG_MTD_NAND_PLATFORM is not set
CONFIG_MTD_ONENAND=y
CONFIG_MTD_ONENAND_VERIFY_WRITE=y
# CONFIG_MTD_ONENAND_GENERIC is not set
# CONFIG_MTD_ONENAND_OMAP2 is not set
# CONFIG_MTD_ONENAND_OTP is not set
# CONFIG_MTD_ONENAND_2X_PROGRAM is not set

#
# LPDDR flash memory drivers
#
# CONFIG_MTD_LPDDR is not set
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_WL_THRESHOLD=4096
CONFIG_MTD_UBI_BEB_LIMIT=20
# CONFIG_MTD_UBI_FASTMAP is not set
# CONFIG_MTD_UBI_GLUEBI is not set
CONFIG_DTC=y
CONFIG_OF=y

#
# Device Tree and Open Firmware support
#
CONFIG_PROC_DEVICETREE=y
# CONFIG_OF_SELFTEST is not set
CONFIG_OF_FLATTREE=y
CONFIG_OF_EARLY_FLATTREE=y
CONFIG_OF_ADDRESS=y
CONFIG_OF_IRQ=y
CONFIG_OF_NET=y
CONFIG_OF_MDIO=y
CONFIG_OF_PCI=y
CONFIG_OF_PCI_IRQ=y
CONFIG_OF_MTD=y
# CONFIG_PARPORT is not set
CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_PCIESSD_MTIP32XX is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_LOOP_MIN_COUNT=8
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_DRBD is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_NVME is not set
# CONFIG_BLK_DEV_SX8 is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=16384
# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
# CONFIG_MG_DISK is not set
# CONFIG_BLK_DEV_RBD is not set
# CONFIG_BLK_DEV_RSXX is not set

#
# Misc devices
#
# CONFIG_SENSORS_LIS3LV02D is not set
# CONFIG_AD525X_DPOT is not set
# CONFIG_ATMEL_PWM is not set
# CONFIG_DUMMY_IRQ is not set
# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
# CONFIG_ICS932S401 is not set
# CONFIG_ATMEL_SSC is not set
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_HP_ILO is not set
# CONFIG_APDS9802ALS is not set
# CONFIG_ISL29003 is not set
# CONFIG_ISL29020 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_SENSORS_BH1780 is not set
# CONFIG_SENSORS_BH1770 is not set
# CONFIG_SENSORS_APDS990X is not set
# CONFIG_HMC6352 is not set
# CONFIG_DS1682 is not set
# CONFIG_TI_DAC7512 is not set
# CONFIG_BMP085_I2C is not set
# CONFIG_BMP085_SPI is not set
# CONFIG_PCH_PHUB is not set
# CONFIG_USB_SWITCH_FSA9480 is not set
# CONFIG_LATTICE_ECP3_CONFIG is not set
# CONFIG_SRAM is not set
CONFIG_CROSSBAR=y
# CONFIG_C2PORT is not set

#
# EEPROM support
#
CONFIG_EEPROM_AT24=m
# CONFIG_EEPROM_AT25 is not set
# CONFIG_EEPROM_LEGACY is not set
# CONFIG_EEPROM_MAX6875 is not set
CONFIG_EEPROM_93CX6=y
# CONFIG_EEPROM_93XX46 is not set
# CONFIG_CB710_CORE is not set

#
# Texas Instruments shared transport line discipline
#
# CONFIG_TI_ST is not set
# CONFIG_SENSORS_LIS3_SPI is not set
# CONFIG_SENSORS_LIS3_I2C is not set

#
# Altera FPGA firmware download module
#
# CONFIG_ALTERA_STAPL is not set
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set

#
# SCSI device support
#
CONFIG_SCSI_MOD=y
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
# CONFIG_CHR_DEV_SG is not set
# CONFIG_CHR_DEV_SCH is not set
CONFIG_SCSI_MULTI_LUN=y
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
CONFIG_SCSI_SCAN_ASYNC=y

#
# SCSI Transports
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
# CONFIG_ISCSI_BOOT_SYSFS is not set
# CONFIG_SCSI_CXGB3_ISCSI is not set
# CONFIG_SCSI_CXGB4_ISCSI is not set
# CONFIG_SCSI_BNX2_ISCSI is not set
# CONFIG_SCSI_BNX2X_FCOE is not set
# CONFIG_BE2ISCSI is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_HPSA is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_3W_SAS is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_MVUMI is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_SCSI_ESAS2R is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_MPT2SAS is not set
# CONFIG_SCSI_MPT3SAS is not set
CONFIG_SCSI_UFSHCD=m
# CONFIG_SCSI_UFSHCD_PCI is not set
# CONFIG_SCSI_UFSHCD_PLATFORM is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_LIBFC is not set
# CONFIG_LIBFCOE is not set
# CONFIG_FCOE is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_PM8001 is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_SCSI_BFA_FC is not set
# CONFIG_SCSI_CHELSIO_FCOE is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y

#
# Controllers with non-SFF native interface
#
CONFIG_SATA_AHCI=y
CONFIG_SATA_AHCI_PLATFORM=m
# CONFIG_SATA_INIC162X is not set
# CONFIG_SATA_ACARD_AHCI is not set
# CONFIG_SATA_SIL24 is not set
CONFIG_SATA_TI=y
CONFIG_ATA_SFF=y

#
# SFF controllers with custom DMA interface
#
# CONFIG_PDC_ADMA is not set
# CONFIG_SATA_QSTOR is not set
# CONFIG_SATA_SX4 is not set
CONFIG_ATA_BMDMA=y

#
# SATA SFF controllers with BMDMA
#
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_HIGHBANK is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_NV is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_RCAR is not set
# CONFIG_SATA_SIL is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_SVW is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set

#
# PATA SFF controllers with BMDMA
#
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARASAN_CF is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
# CONFIG_PATA_CS5536 is not set
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_PATA_HPT366 is not set
# CONFIG_PATA_HPT37X is not set
# CONFIG_PATA_HPT3X2N is not set
# CONFIG_PATA_HPT3X3 is not set
# CONFIG_PATA_IT8213 is not set
# CONFIG_PATA_IT821X is not set
# CONFIG_PATA_JMICRON is not set
# CONFIG_PATA_MARVELL is not set
# CONFIG_PATA_NETCELL is not set
# CONFIG_PATA_NINJA32 is not set
# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC2027X is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
# CONFIG_PATA_RDC is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SCH is not set
# CONFIG_PATA_SERVERWORKS is not set
# CONFIG_PATA_SIL680 is not set
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_TOSHIBA is not set
# CONFIG_PATA_TRIFLEX is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set

#
# PIO-only SFF controllers
#
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_PLATFORM is not set
# CONFIG_PATA_RZ1000 is not set

#
# Generic fallback / legacy drivers
#
# CONFIG_ATA_GENERIC is not set
# CONFIG_PATA_LEGACY is not set
CONFIG_MD=y
# CONFIG_BLK_DEV_MD is not set
# CONFIG_BCACHE is not set
# CONFIG_BLK_DEV_DM is not set
# CONFIG_TARGET_CORE is not set
# CONFIG_FUSION is not set

#
# IEEE 1394 (FireWire) support
#
# CONFIG_FIREWIRE is not set
# CONFIG_FIREWIRE_NOSY is not set
# CONFIG_I2O is not set
CONFIG_NETDEVICES=y
CONFIG_MII=m
CONFIG_NET_CORE=y
# CONFIG_BONDING is not set
# CONFIG_DUMMY is not set
# CONFIG_EQUALIZER is not set
# CONFIG_NET_FC is not set
# CONFIG_NET_TEAM is not set
# CONFIG_MACVLAN is not set
# CONFIG_VXLAN is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_TUN is not set
# CONFIG_VETH is not set
CONFIG_NLMON=m
# CONFIG_ARCNET is not set

#
# CAIF transport drivers
#

#
# Distributed Switch Architecture drivers
#
# CONFIG_NET_DSA_MV88E6XXX is not set
# CONFIG_NET_DSA_MV88E6060 is not set
# CONFIG_NET_DSA_MV88E6XXX_NEED_PPU is not set
# CONFIG_NET_DSA_MV88E6131 is not set
# CONFIG_NET_DSA_MV88E6123_61_65 is not set
CONFIG_ETHERNET=y
# CONFIG_NET_VENDOR_3COM is not set
CONFIG_NET_VENDOR_ADAPTEC=y
# CONFIG_ADAPTEC_STARFIRE is not set
CONFIG_NET_VENDOR_ALTEON=y
# CONFIG_ACENIC is not set
CONFIG_NET_VENDOR_AMD=y
# CONFIG_AMD8111_ETH is not set
# CONFIG_PCNET32 is not set
CONFIG_NET_VENDOR_ARC=y
# CONFIG_ARC_EMAC is not set
CONFIG_NET_VENDOR_ATHEROS=y
# CONFIG_ATL2 is not set
# CONFIG_ATL1 is not set
# CONFIG_ATL1E is not set
# CONFIG_ATL1C is not set
# CONFIG_ALX is not set
CONFIG_NET_CADENCE=y
# CONFIG_ARM_AT91_ETHER is not set
# CONFIG_MACB is not set
# CONFIG_NET_VENDOR_BROADCOM is not set
CONFIG_NET_VENDOR_BROCADE=y
# CONFIG_BNA is not set
# CONFIG_NET_CALXEDA_XGMAC is not set
CONFIG_NET_VENDOR_CHELSIO=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
# CONFIG_CHELSIO_T4 is not set
# CONFIG_CHELSIO_T4VF is not set
# CONFIG_NET_VENDOR_CIRRUS is not set
CONFIG_NET_VENDOR_CISCO=y
# CONFIG_ENIC is not set
# CONFIG_DM9000 is not set
# CONFIG_DNET is not set
CONFIG_NET_VENDOR_DEC=y
# CONFIG_NET_TULIP is not set
CONFIG_NET_VENDOR_DLINK=y
# CONFIG_DL2K is not set
# CONFIG_SUNDANCE is not set
CONFIG_NET_VENDOR_EMULEX=y
# CONFIG_BE2NET is not set
CONFIG_NET_VENDOR_EXAR=y
# CONFIG_S2IO is not set
# CONFIG_VXGE is not set
# CONFIG_NET_VENDOR_FARADAY is not set
CONFIG_NET_VENDOR_HP=y
# CONFIG_HP100 is not set
# CONFIG_NET_VENDOR_INTEL is not set
# CONFIG_IP1000 is not set
# CONFIG_JME is not set
# CONFIG_NET_VENDOR_MARVELL is not set
CONFIG_NET_VENDOR_MELLANOX=y
# CONFIG_MLX4_EN is not set
# CONFIG_MLX4_CORE is not set
# CONFIG_NET_VENDOR_MICREL is not set
# CONFIG_NET_VENDOR_MICROCHIP is not set
CONFIG_NET_VENDOR_MYRI=y
# CONFIG_MYRI10GE is not set
# CONFIG_FEALNX is not set
# CONFIG_NET_VENDOR_NATSEMI is not set
CONFIG_NET_VENDOR_NVIDIA=y
# CONFIG_FORCEDETH is not set
CONFIG_NET_VENDOR_OKI=y
# CONFIG_ETHOC is not set
CONFIG_NET_PACKET_ENGINE=y
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
CONFIG_NET_VENDOR_QLOGIC=y
# CONFIG_QLA3XXX is not set
# CONFIG_QLCNIC is not set
# CONFIG_QLGE is not set
# CONFIG_NETXEN_NIC is not set
CONFIG_NET_VENDOR_REALTEK=y
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_R8169 is not set
# CONFIG_SH_ETH is not set
CONFIG_NET_VENDOR_RDC=y
# CONFIG_R6040 is not set
# CONFIG_NET_VENDOR_SEEQ is not set
CONFIG_NET_VENDOR_SILAN=y
# CONFIG_SC92031 is not set
CONFIG_NET_VENDOR_SIS=y
# CONFIG_SIS900 is not set
# CONFIG_SIS190 is not set
# CONFIG_SFC is not set
# CONFIG_NET_VENDOR_SMSC is not set
# CONFIG_NET_VENDOR_STMICRO is not set
CONFIG_NET_VENDOR_SUN=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NIU is not set
CONFIG_NET_VENDOR_TEHUTI=y
# CONFIG_TEHUTI is not set
CONFIG_NET_VENDOR_TI=y
# CONFIG_TI_DAVINCI_EMAC is not set
CONFIG_TI_DAVINCI_MDIO=y
CONFIG_TI_DAVINCI_CPDMA=y
CONFIG_TI_CPSW_PHY_SEL=y
CONFIG_TI_CPSW=y
# CONFIG_TI_CPTS is not set
# CONFIG_TLAN is not set
# CONFIG_NET_VENDOR_VIA is not set
# CONFIG_NET_VENDOR_WIZNET is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
CONFIG_PHYLIB=y

#
# MII PHY device drivers
#
# CONFIG_AT803X_PHY is not set
# CONFIG_AMD_PHY is not set
# CONFIG_MARVELL_PHY is not set
# CONFIG_DAVICOM_PHY is not set
# CONFIG_QSEMI_PHY is not set
# CONFIG_LXT_PHY is not set
# CONFIG_CICADA_PHY is not set
# CONFIG_VITESSE_PHY is not set
CONFIG_SMSC_PHY=y
# CONFIG_BROADCOM_PHY is not set
# CONFIG_BCM87XX_PHY is not set
# CONFIG_ICPLUS_PHY is not set
# CONFIG_REALTEK_PHY is not set
# CONFIG_NATIONAL_PHY is not set
# CONFIG_STE10XP is not set
# CONFIG_LSI_ET1011C_PHY is not set
# CONFIG_MICREL_PHY is not set
# CONFIG_FIXED_PHY is not set
# CONFIG_MDIO_BITBANG is not set
# CONFIG_MDIO_BUS_MUX_GPIO is not set
# CONFIG_MDIO_BUS_MUX_MMIOREG is not set
# CONFIG_MICREL_KS8995MA is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set

#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_RTL8152 is not set
CONFIG_USB_USBNET=m
CONFIG_USB_NET_AX8817X=m
CONFIG_USB_NET_AX88179_178A=m
CONFIG_USB_NET_CDCETHER=m
# CONFIG_USB_NET_CDC_EEM is not set
CONFIG_USB_NET_CDC_NCM=m
# CONFIG_USB_NET_CDC_MBIM is not set
# CONFIG_USB_NET_DM9601 is not set
# CONFIG_USB_NET_SR9700 is not set
# CONFIG_USB_NET_SMSC75XX is not set
CONFIG_USB_NET_SMSC95XX=m
# CONFIG_USB_NET_GL620A is not set
CONFIG_USB_NET_NET1080=m
# CONFIG_USB_NET_PLUSB is not set
# CONFIG_USB_NET_MCS7830 is not set
# CONFIG_USB_NET_RNDIS_HOST is not set
CONFIG_USB_NET_CDC_SUBSET=m
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_BELKIN=y
CONFIG_USB_ARMLINUX=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_KC2190=y
CONFIG_USB_NET_ZAURUS=m
# CONFIG_USB_NET_CX82310_ETH is not set
# CONFIG_USB_NET_KALMIA is not set
CONFIG_USB_NET_QMI_WWAN=m
# CONFIG_USB_NET_INT51X1 is not set
# CONFIG_USB_IPHETH is not set
# CONFIG_USB_SIERRA_NET is not set
# CONFIG_USB_VL600 is not set
CONFIG_WLAN=y
# CONFIG_ATMEL is not set
# CONFIG_PRISM54 is not set
# CONFIG_USB_ZD1201 is not set
# CONFIG_HOSTAP is not set
# CONFIG_WL_TI is not set

#
# Enable WiMAX (Networking options) to see the WiMAX drivers
#
# CONFIG_WAN is not set
# CONFIG_VMXNET3 is not set
# CONFIG_ISDN is not set

#
# Input device support
#
CONFIG_INPUT=y
CONFIG_INPUT_FF_MEMLESS=m
CONFIG_INPUT_POLLDEV=m
# CONFIG_INPUT_SPARSEKMAP is not set
# CONFIG_INPUT_MATRIXKMAP is not set

#
# Userland interfaces
#
# CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_SERIO_ALTERA_PS2 is not set
# CONFIG_SERIO_PS2MULT is not set
# CONFIG_SERIO_ARC_PS2 is not set
# CONFIG_SERIO_APBPS2 is not set
# CONFIG_SERIO_OLPC_APSP is not set
# CONFIG_GAMEPORT is not set

#
# Character devices
#
CONFIG_TTY=y
CONFIG_VT=y
CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_VT_CONSOLE_SLEEP=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_UNIX98_PTYS=y
# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_NOZOMI is not set
# CONFIG_N_GSM is not set
# CONFIG_TRACE_SINK is not set
CONFIG_DEVKMEM=y

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_DMA=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_NR_UARTS=32
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
CONFIG_SERIAL_8250_DETECT_IRQ=y
CONFIG_SERIAL_8250_RSA=y
# CONFIG_SERIAL_8250_DW is not set
# CONFIG_SERIAL_8250_EM is not set

#
# Non-8250 serial port support
#
# CONFIG_SERIAL_MAX3100 is not set
# CONFIG_SERIAL_MAX310X is not set
# CONFIG_SERIAL_MFD_HSU is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
# CONFIG_SERIAL_OF_PLATFORM is not set
CONFIG_SERIAL_OMAP=y
CONFIG_SERIAL_OMAP_CONSOLE=y
# CONFIG_SERIAL_SCCNXP is not set
# CONFIG_SERIAL_TIMBERDALE is not set
# CONFIG_SERIAL_ALTERA_JTAGUART is not set
# CONFIG_SERIAL_ALTERA_UART is not set
# CONFIG_SERIAL_IFX6X60 is not set
# CONFIG_SERIAL_PCH_UART is not set
# CONFIG_SERIAL_XILINX_PS_UART is not set
# CONFIG_SERIAL_ARC is not set
# CONFIG_SERIAL_RP2 is not set
# CONFIG_SERIAL_FSL_LPUART is not set
# CONFIG_SERIAL_ST_ASC is not set
# CONFIG_TTY_PRINTK is not set
# CONFIG_HVC_DCC is not set
# CONFIG_IPMI_HANDLER is not set
CONFIG_HW_RANDOM=y
# CONFIG_HW_RANDOM_TIMERIOMEM is not set
# CONFIG_HW_RANDOM_ATMEL is not set
CONFIG_HW_RANDOM_OMAP=y
# CONFIG_HW_RANDOM_EXYNOS is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
CONFIG_DEVPORT=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_MUX=y

#
# Multiplexer I2C Chip support
#
# CONFIG_I2C_ARB_GPIO_CHALLENGE is not set
# CONFIG_I2C_MUX_GPIO is not set
# CONFIG_I2C_MUX_PCA9541 is not set
CONFIG_I2C_MUX_PCA954x=y
# CONFIG_I2C_MUX_PINCTRL is not set
CONFIG_I2C_HELPER_AUTO=y

#
# I2C Hardware Bus support
#

#
# PC SMBus host controller drivers
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_ISCH is not set
# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set

#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
# CONFIG_I2C_CBUS_GPIO is not set
# CONFIG_I2C_DESIGNWARE_PLATFORM is not set
# CONFIG_I2C_DESIGNWARE_PCI is not set
# CONFIG_I2C_EG20T is not set
# CONFIG_I2C_GPIO is not set
# CONFIG_I2C_OCORES is not set
CONFIG_I2C_OMAP=y
# CONFIG_I2C_PCA_PLATFORM is not set
# CONFIG_I2C_PCA954X is not set
# CONFIG_I2C_PXA_PCI is not set
# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_XILINX is not set

#
# External I2C/SMBus adapter drivers
#
# CONFIG_I2C_DIOLAN_U2C is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_TAOS_EVM is not set
# CONFIG_I2C_TINY_USB is not set

#
# Other I2C/SMBus bus drivers
#
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
CONFIG_SPI=y
# CONFIG_SPI_DEBUG is not set
CONFIG_SPI_MASTER=y

#
# SPI Master Controller Drivers
#
# CONFIG_SPI_ALTERA is not set
# CONFIG_SPI_BITBANG is not set
# CONFIG_SPI_GPIO is not set
# CONFIG_SPI_FSL_SPI is not set
# CONFIG_SPI_FSL_DSPI is not set
# CONFIG_SPI_OC_TINY is not set
CONFIG_SPI_OMAP24XX=y
CONFIG_SPI_TI_QSPI=y
# CONFIG_SPI_PXA2XX is not set
# CONFIG_SPI_PXA2XX_PCI is not set
# CONFIG_SPI_SC18IS602 is not set
# CONFIG_SPI_TOPCLIFF_PCH is not set
# CONFIG_SPI_XCOMM is not set
# CONFIG_SPI_XILINX is not set
# CONFIG_SPI_DESIGNWARE is not set

#
# SPI Protocol Masters
#
# CONFIG_SPI_SPIDEV is not set
# CONFIG_SPI_TLE62X0 is not set
# CONFIG_HSI is not set

#
# PPS support
#
CONFIG_PPS=m
# CONFIG_PPS_DEBUG is not set

#
# PPS clients support
#
# CONFIG_PPS_CLIENT_KTIMER is not set
# CONFIG_PPS_CLIENT_LDISC is not set
# CONFIG_PPS_CLIENT_GPIO is not set

#
# PPS generators support
#

#
# PTP clock support
#
CONFIG_PTP_1588_CLOCK=m

#
# Enable PHYLIB and NETWORK_PHY_TIMESTAMPING to see the additional clocks.
#
CONFIG_PINCTRL=y

#
# Pin controllers
#
CONFIG_PINMUX=y
CONFIG_PINCONF=y
CONFIG_GENERIC_PINCONF=y
# CONFIG_DEBUG_PINCTRL is not set
CONFIG_PINCTRL_SINGLE=y
CONFIG_PINCTRL_PALMAS=y
CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
CONFIG_ARCH_REQUIRE_GPIOLIB=y
CONFIG_GPIO_DEVRES=y
CONFIG_GPIOLIB=y
CONFIG_OF_GPIO=y
CONFIG_DEBUG_GPIO=y
CONFIG_GPIO_SYSFS=y

#
# Memory mapped GPIO drivers:
#
# CONFIG_GPIO_GENERIC_PLATFORM is not set
# CONFIG_GPIO_EM is not set
# CONFIG_GPIO_RCAR is not set
# CONFIG_GPIO_TS5500 is not set
# CONFIG_GPIO_VX855 is not set
# CONFIG_GPIO_GRGPIO is not set

#
# I2C GPIO expanders:
#
# CONFIG_GPIO_MAX7300 is not set
# CONFIG_GPIO_MAX732X is not set
# CONFIG_GPIO_PCA953X_IRQ is not set
CONFIG_GPIO_PCF857X=y
# CONFIG_GPIO_SX150X is not set
CONFIG_GPIO_TWL4030=y
# CONFIG_GPIO_TWL6040 is not set
# CONFIG_GPIO_ADP5588 is not set
# CONFIG_GPIO_ADNP is not set

#
# PCI GPIO expanders:
#
# CONFIG_GPIO_BT8XX is not set
# CONFIG_GPIO_AMD8111 is not set
# CONFIG_GPIO_ML_IOH is not set
# CONFIG_GPIO_RDC321X is not set

#
# SPI GPIO expanders:
#
# CONFIG_GPIO_MAX7301 is not set
# CONFIG_GPIO_MCP23S08 is not set
# CONFIG_GPIO_MC33880 is not set
# CONFIG_GPIO_74X164 is not set

#
# AC97 GPIO expanders:
#

#
# LPC GPIO expanders:
#

#
# MODULbus GPIO expanders:
#
CONFIG_GPIO_PALMAS=y
# CONFIG_GPIO_TPS65910 is not set

#
# USB GPIO expanders:
#
CONFIG_W1=y
CONFIG_W1_CON=y

#
# 1-wire Bus Masters
#
# CONFIG_W1_MASTER_MATROX is not set
# CONFIG_W1_MASTER_DS2490 is not set
# CONFIG_W1_MASTER_DS2482 is not set
# CONFIG_W1_MASTER_DS1WM is not set
# CONFIG_W1_MASTER_GPIO is not set
# CONFIG_HDQ_MASTER_OMAP is not set

#
# 1-wire Slaves
#
# CONFIG_W1_SLAVE_THERM is not set
# CONFIG_W1_SLAVE_SMEM is not set
# CONFIG_W1_SLAVE_DS2408 is not set
# CONFIG_W1_SLAVE_DS2413 is not set
# CONFIG_W1_SLAVE_DS2423 is not set
# CONFIG_W1_SLAVE_DS2431 is not set
# CONFIG_W1_SLAVE_DS2433 is not set
# CONFIG_W1_SLAVE_DS2760 is not set
# CONFIG_W1_SLAVE_DS2780 is not set
# CONFIG_W1_SLAVE_DS2781 is not set
# CONFIG_W1_SLAVE_DS28E04 is not set
# CONFIG_W1_SLAVE_BQ27000 is not set
CONFIG_POWER_SUPPLY=y
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_PDA_POWER is not set
# CONFIG_TEST_POWER is not set
# CONFIG_BATTERY_DS2780 is not set
# CONFIG_BATTERY_DS2781 is not set
# CONFIG_BATTERY_DS2782 is not set
# CONFIG_BATTERY_SBS is not set
# CONFIG_BATTERY_BQ27x00 is not set
# CONFIG_BATTERY_MAX17040 is not set
# CONFIG_BATTERY_MAX17042 is not set
# CONFIG_CHARGER_ISP1704 is not set
# CONFIG_CHARGER_MAX8903 is not set
# CONFIG_CHARGER_TWL4030 is not set
# CONFIG_CHARGER_LP8727 is not set
# CONFIG_CHARGER_GPIO is not set
# CONFIG_CHARGER_MANAGER is not set
# CONFIG_CHARGER_BQ2415X is not set
# CONFIG_CHARGER_BQ24190 is not set
# CONFIG_CHARGER_SMB347 is not set
# CONFIG_POWER_RESET is not set
# CONFIG_POWER_RESET_RESTART is not set
# CONFIG_POWER_AVS is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
# CONFIG_HWMON_DEBUG_CHIP is not set

#
# Native drivers
#
# CONFIG_SENSORS_AD7314 is not set
# CONFIG_SENSORS_AD7414 is not set
# CONFIG_SENSORS_AD7418 is not set
# CONFIG_SENSORS_ADCXX is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1029 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ADT7310 is not set
# CONFIG_SENSORS_ADT7410 is not set
# CONFIG_SENSORS_ADT7411 is not set
# CONFIG_SENSORS_ADT7462 is not set
# CONFIG_SENSORS_ADT7470 is not set
# CONFIG_SENSORS_ADT7475 is not set
# CONFIG_SENSORS_ASC7621 is not set
# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS620 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_I5K_AMB is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_F75375S is not set
# CONFIG_SENSORS_G760A is not set
# CONFIG_SENSORS_G762 is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_GL520SM is not set
# CONFIG_SENSORS_GPIO_FAN is not set
# CONFIG_SENSORS_HIH6130 is not set
# CONFIG_SENSORS_HTU21 is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_JC42 is not set
# CONFIG_SENSORS_LINEAGE is not set
# CONFIG_SENSORS_LM63 is not set
# CONFIG_SENSORS_LM70 is not set
# CONFIG_SENSORS_LM73 is not set
CONFIG_SENSORS_LM75=m
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# CONFIG_SENSORS_LM80 is not set
# CONFIG_SENSORS_LM83 is not set
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_LM93 is not set
# CONFIG_SENSORS_LTC4151 is not set
# CONFIG_SENSORS_LTC4215 is not set
# CONFIG_SENSORS_LTC4245 is not set
# CONFIG_SENSORS_LTC4261 is not set
# CONFIG_SENSORS_LM95234 is not set
# CONFIG_SENSORS_LM95241 is not set
# CONFIG_SENSORS_LM95245 is not set
# CONFIG_SENSORS_MAX1111 is not set
# CONFIG_SENSORS_MAX16065 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_MAX1668 is not set
# CONFIG_SENSORS_MAX197 is not set
# CONFIG_SENSORS_MAX6639 is not set
# CONFIG_SENSORS_MAX6642 is not set
# CONFIG_SENSORS_MAX6650 is not set
# CONFIG_SENSORS_MAX6697 is not set
# CONFIG_SENSORS_MCP3021 is not set
# CONFIG_SENSORS_NCT6775 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_PMBUS is not set
# CONFIG_SENSORS_SHT15 is not set
# CONFIG_SENSORS_SHT21 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_SMM665 is not set
# CONFIG_SENSORS_DME1737 is not set
# CONFIG_SENSORS_EMC1403 is not set
# CONFIG_SENSORS_EMC2103 is not set
# CONFIG_SENSORS_EMC6W201 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_SCH56XX_COMMON is not set
# CONFIG_SENSORS_SCH5627 is not set
# CONFIG_SENSORS_SCH5636 is not set
# CONFIG_SENSORS_ADS1015 is not set
# CONFIG_SENSORS_ADS7828 is not set
# CONFIG_SENSORS_ADS7871 is not set
# CONFIG_SENSORS_AMC6821 is not set
# CONFIG_SENSORS_INA209 is not set
# CONFIG_SENSORS_INA2XX is not set
# CONFIG_SENSORS_THMC50 is not set
# CONFIG_SENSORS_TMP102 is not set
# CONFIG_SENSORS_TMP401 is not set
# CONFIG_SENSORS_TMP421 is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83792D is not set
# CONFIG_SENSORS_W83793 is not set
# CONFIG_SENSORS_W83795 is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83L786NG is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
CONFIG_THERMAL=y
CONFIG_THERMAL_HWMON=y
CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
# CONFIG_THERMAL_DEFAULT_GOV_FAIR_SHARE is not set
# CONFIG_THERMAL_DEFAULT_GOV_USER_SPACE is not set
CONFIG_THERMAL_GOV_FAIR_SHARE=y
CONFIG_THERMAL_GOV_STEP_WISE=y
CONFIG_THERMAL_GOV_USER_SPACE=y
# CONFIG_THERMAL_EMULATION is not set

#
# Texas Instruments thermal drivers
#
CONFIG_TI_SOC_THERMAL=y
# CONFIG_OMAP4_THERMAL is not set
# CONFIG_OMAP5_THERMAL is not set
CONFIG_DRA752_THERMAL=y
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_CORE=y
# CONFIG_WATCHDOG_NOWAYOUT is not set

#
# Watchdog Device Drivers
#
# CONFIG_SOFT_WATCHDOG is not set
# CONFIG_DW_WATCHDOG is not set
CONFIG_OMAP_WATCHDOG=y
CONFIG_TWL4030_WATCHDOG=y
# CONFIG_MAX63XX_WATCHDOG is not set
# CONFIG_ALIM7101_WDT is not set
# CONFIG_I6300ESB_WDT is not set
# CONFIG_MEN_A21_WDT is not set

#
# PCI-based Watchdog Cards
#
# CONFIG_PCIPCWATCHDOG is not set
# CONFIG_WDTPCI is not set

#
# USB-based Watchdog Cards
#
# CONFIG_USBPCWATCHDOG is not set
CONFIG_SSB_POSSIBLE=y

#
# Sonics Silicon Backplane
#
# CONFIG_SSB is not set
CONFIG_BCMA_POSSIBLE=y

#
# Broadcom specific AMBA
#
# CONFIG_BCMA is not set

#
# Multifunction device drivers
#
CONFIG_MFD_CORE=y
# CONFIG_MFD_AS3711 is not set
# CONFIG_PMIC_ADP5520 is not set
# CONFIG_MFD_AAT2870_CORE is not set
# CONFIG_MFD_CROS_EC is not set
# CONFIG_MFD_ASIC3 is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_DA9052_SPI is not set
# CONFIG_MFD_DA9052_I2C is not set
# CONFIG_MFD_DA9055 is not set
# CONFIG_MFD_DA9063 is not set
# CONFIG_MFD_MC13XXX_SPI is not set
# CONFIG_MFD_MC13XXX_I2C is not set
# CONFIG_HTC_EGPIO is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_HTC_I2CPLD is not set
# CONFIG_LPC_ICH is not set
# CONFIG_LPC_SCH is not set
# CONFIG_MFD_JANZ_CMODIO is not set
# CONFIG_MFD_KEMPLD is not set
# CONFIG_MFD_88PM800 is not set
# CONFIG_MFD_88PM805 is not set
# CONFIG_MFD_88PM860X is not set
# CONFIG_MFD_MAX77686 is not set
# CONFIG_MFD_MAX77693 is not set
# CONFIG_MFD_MAX8907 is not set
# CONFIG_MFD_MAX8925 is not set
# CONFIG_MFD_MAX8997 is not set
# CONFIG_MFD_MAX8998 is not set
# CONFIG_EZX_PCAP is not set
# CONFIG_MFD_VIPERBOARD is not set
# CONFIG_MFD_RETU is not set
# CONFIG_MFD_PCF50633 is not set
# CONFIG_MFD_RDC321X is not set
# CONFIG_MFD_RTSX_PCI is not set
# CONFIG_MFD_RC5T583 is not set
# CONFIG_MFD_SEC_CORE is not set
# CONFIG_MFD_SI476X_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_MFD_SMSC is not set
# CONFIG_ABX500_CORE is not set
# CONFIG_MFD_STMPE is not set
# CONFIG_MFD_SYSCON is not set
# CONFIG_MFD_TI_AM335X_TSCADC is not set
# CONFIG_MFD_LP8788 is not set
CONFIG_MFD_OMAP_USB_HOST=y
CONFIG_MFD_PALMAS=y
# CONFIG_TPS6105X is not set
# CONFIG_TPS65010 is not set
# CONFIG_TPS6507X is not set
# CONFIG_MFD_TPS65090 is not set
CONFIG_MFD_TPS65217=y
# CONFIG_MFD_TPS65218 is not set
# CONFIG_MFD_TPS6586X is not set
CONFIG_MFD_TPS65910=y
# CONFIG_MFD_TPS65912 is not set
# CONFIG_MFD_TPS65912_I2C is not set
# CONFIG_MFD_TPS65912_SPI is not set
# CONFIG_MFD_TPS80031 is not set
CONFIG_TWL4030_CORE=y
# CONFIG_TWL4030_MADC is not set
CONFIG_TWL4030_POWER=y
# CONFIG_MFD_TWL4030_AUDIO is not set
CONFIG_TWL6040_CORE=y
# CONFIG_MFD_WL1273_CORE is not set
# CONFIG_MFD_LM3533 is not set
# CONFIG_MFD_TIMBERDALE is not set
# CONFIG_MFD_TC3589X is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_MFD_T7L66XB is not set
# CONFIG_MFD_TC6387XB is not set
# CONFIG_MFD_TC6393XB is not set
# CONFIG_MFD_VX855 is not set
# CONFIG_MFD_ARIZONA_I2C is not set
# CONFIG_MFD_ARIZONA_SPI is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_WM831X_I2C is not set
# CONFIG_MFD_WM831X_SPI is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_WM8994 is not set
# CONFIG_VEXPRESS_CONFIG is not set
CONFIG_REGULATOR=y
# CONFIG_REGULATOR_DEBUG is not set
# CONFIG_REGULATOR_DUMMY is not set
CONFIG_REGULATOR_FIXED_VOLTAGE=y
# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
# CONFIG_REGULATOR_AD5398 is not set
# CONFIG_REGULATOR_DA9210 is not set
# CONFIG_REGULATOR_FAN53555 is not set
# CONFIG_REGULATOR_GPIO is not set
# CONFIG_REGULATOR_ISL6271A is not set
# CONFIG_REGULATOR_LP3971 is not set
# CONFIG_REGULATOR_LP3972 is not set
# CONFIG_REGULATOR_LP872X is not set
# CONFIG_REGULATOR_LP8755 is not set
# CONFIG_REGULATOR_MAX1586 is not set
# CONFIG_REGULATOR_MAX8649 is not set
# CONFIG_REGULATOR_MAX8660 is not set
# CONFIG_REGULATOR_MAX8952 is not set
# CONFIG_REGULATOR_MAX8973 is not set
CONFIG_REGULATOR_PALMAS=y
# CONFIG_REGULATOR_PFUZE100 is not set
# CONFIG_REGULATOR_TI_ABB is not set
# CONFIG_REGULATOR_TPS51632 is not set
# CONFIG_REGULATOR_TPS62360 is not set
CONFIG_REGULATOR_TPS65023=y
CONFIG_REGULATOR_TPS6507X=y
CONFIG_REGULATOR_TPS65217=y
# CONFIG_REGULATOR_TPS6524X is not set
CONFIG_REGULATOR_TPS65910=y
CONFIG_REGULATOR_TWL4030=y
# CONFIG_REGULATOR_TIAVSCLASS0 is not set
# CONFIG_MEDIA_SUPPORT is not set

#
# Graphics support
#
CONFIG_VGA_ARB=y
CONFIG_VGA_ARB_MAX_GPUS=16
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
# CONFIG_FB_DDC is not set
# CONFIG_FB_BOOT_VESA_SUPPORT is not set
# CONFIG_FB_CFB_FILLRECT is not set
# CONFIG_FB_CFB_COPYAREA is not set
# CONFIG_FB_CFB_IMAGEBLIT is not set
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
# CONFIG_FB_FOREIGN_ENDIAN is not set
# CONFIG_FB_SYS_FOPS is not set
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y

#
# Frame buffer hardware drivers
#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_UVESA is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_NVIDIA is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_I740 is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_S3 is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_VT8623 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_CARMINE is not set
# CONFIG_FB_TMIO is not set
# CONFIG_FB_SMSCUFX is not set
# CONFIG_FB_UDL is not set
# CONFIG_FB_GOLDFISH is not set
# CONFIG_FB_DA8XX is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FB_METRONOME is not set
# CONFIG_FB_MB862XX is not set
# CONFIG_FB_BROADSHEET is not set
# CONFIG_FB_AUO_K190X is not set
# CONFIG_FB_SIMPLE is not set
# CONFIG_OMAP2_DSS is not set
# CONFIG_EXYNOS_VIDEO is not set
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=y
# CONFIG_LCD_L4F00242T03 is not set
# CONFIG_LCD_LMS283GF05 is not set
# CONFIG_LCD_LTV350QV is not set
# CONFIG_LCD_ILI922X is not set
# CONFIG_LCD_ILI9320 is not set
# CONFIG_LCD_TDO24M is not set
# CONFIG_LCD_VGG2432A4 is not set
CONFIG_LCD_PLATFORM=y
# CONFIG_LCD_S6E63M0 is not set
# CONFIG_LCD_LD9040 is not set
# CONFIG_LCD_AMS369FG06 is not set
# CONFIG_LCD_LMS501KF03 is not set
# CONFIG_LCD_HX8357 is not set
CONFIG_BACKLIGHT_CLASS_DEVICE=y
CONFIG_BACKLIGHT_GENERIC=y
# CONFIG_BACKLIGHT_ADP8860 is not set
# CONFIG_BACKLIGHT_ADP8870 is not set
# CONFIG_BACKLIGHT_LM3630 is not set
# CONFIG_BACKLIGHT_LM3639 is not set
# CONFIG_BACKLIGHT_LP855X is not set
# CONFIG_BACKLIGHT_PANDORA is not set
# CONFIG_BACKLIGHT_TPS65217 is not set
# CONFIG_BACKLIGHT_GPIO is not set
# CONFIG_BACKLIGHT_LV5207LP is not set
# CONFIG_BACKLIGHT_BD6107 is not set

#
# Console display driver support
#
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
# CONFIG_FB_SSD1307 is not set
# CONFIG_SOUND is not set

#
# HID support
#
CONFIG_HID=y
# CONFIG_HID_BATTERY_STRENGTH is not set
# CONFIG_HIDRAW is not set
# CONFIG_UHID is not set
CONFIG_HID_GENERIC=y

#
# Special HID drivers
#
# CONFIG_HID_A4TECH is not set
# CONFIG_HID_ACRUX is not set
# CONFIG_HID_APPLE is not set
# CONFIG_HID_APPLEIR is not set
# CONFIG_HID_AUREAL is not set
# CONFIG_HID_BELKIN is not set
# CONFIG_HID_CHERRY is not set
# CONFIG_HID_CHICONY is not set
# CONFIG_HID_CYPRESS is not set
# CONFIG_HID_DRAGONRISE is not set
# CONFIG_HID_EMS_FF is not set
# CONFIG_HID_ELECOM is not set
# CONFIG_HID_ELO is not set
# CONFIG_HID_EZKEY is not set
# CONFIG_HID_HOLTEK is not set
# CONFIG_HID_HUION is not set
# CONFIG_HID_KEYTOUCH is not set
# CONFIG_HID_KYE is not set
# CONFIG_HID_UCLOGIC is not set
# CONFIG_HID_WALTOP is not set
# CONFIG_HID_GYRATION is not set
# CONFIG_HID_ICADE is not set
# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
# CONFIG_HID_LCPOWER is not set
# CONFIG_HID_LENOVO_TPKBD is not set
# CONFIG_HID_LOGITECH is not set
# CONFIG_HID_MAGICMOUSE is not set
# CONFIG_HID_MICROSOFT is not set
# CONFIG_HID_MONTEREY is not set
# CONFIG_HID_MULTITOUCH is not set
# CONFIG_HID_NTRIG is not set
# CONFIG_HID_ORTEK is not set
# CONFIG_HID_PANTHERLORD is not set
# CONFIG_HID_PETALYNX is not set
# CONFIG_HID_PICOLCD is not set
# CONFIG_HID_PRIMAX is not set
# CONFIG_HID_ROCCAT is not set
# CONFIG_HID_SAITEK is not set
# CONFIG_HID_SAMSUNG is not set
# CONFIG_HID_SONY is not set
# CONFIG_HID_SPEEDLINK is not set
# CONFIG_HID_STEELSERIES is not set
# CONFIG_HID_SUNPLUS is not set
# CONFIG_HID_GREENASIA is not set
# CONFIG_HID_SMARTJOYPLUS is not set
# CONFIG_HID_TIVO is not set
# CONFIG_HID_TOPSEED is not set
# CONFIG_HID_THINGM is not set
# CONFIG_HID_THRUSTMASTER is not set
# CONFIG_HID_WACOM is not set
# CONFIG_HID_WIIMOTE is not set
# CONFIG_HID_XINMO is not set
# CONFIG_HID_ZEROPLUS is not set
# CONFIG_HID_ZYDACRON is not set
# CONFIG_HID_SENSOR_HUB is not set

#
# USB HID support
#
CONFIG_USB_HID=y
# CONFIG_HID_PID is not set
# CONFIG_USB_HIDDEV is not set

#
# I2C HID support
#
# CONFIG_I2C_HID is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB_SUPPORT=y
CONFIG_USB_COMMON=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y

#
# Miscellaneous USB options
#
CONFIG_USB_DEFAULT_PERSIST=y
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_OTG is not set
# CONFIG_USB_OTG_WHITELIST is not set
# CONFIG_USB_OTG_BLACKLIST_HUB is not set
CONFIG_USB_MON=y
# CONFIG_USB_WUSB_CBAF is not set

#
# USB Host Controller Drivers
#
# CONFIG_USB_C67X00_HCD is not set
CONFIG_USB_XHCI_HCD=m
CONFIG_USB_XHCI_PLATFORM=m
CONFIG_USB_EHCI_HCD=m
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
CONFIG_USB_EHCI_TT_NEWSCHED=y
CONFIG_USB_EHCI_PCI=m
CONFIG_USB_EHCI_HCD_OMAP=m
# CONFIG_USB_EHCI_HCD_PLATFORM is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
# CONFIG_USB_ISP1362_HCD is not set
# CONFIG_USB_FUSBH200_HCD is not set
# CONFIG_USB_FOTG210_HCD is not set
# CONFIG_USB_OHCI_HCD is not set
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
# CONFIG_USB_HCD_TEST_MODE is not set
# CONFIG_USB_MUSB_HDRC is not set
# CONFIG_USB_RENESAS_USBHS is not set

#
# USB Device Class drivers
#
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
CONFIG_USB_WDM=y
# CONFIG_USB_TMC is not set

#
# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
#

#
# also be needed; see USB_STORAGE Help for more info
#
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_REALTEK is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
# CONFIG_USB_STORAGE_ONETOUCH is not set
# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
# CONFIG_USB_STORAGE_ENE_UB6250 is not set

#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
CONFIG_USB_DWC3=m
CONFIG_USB_DWC3_HOST=y
# CONFIG_USB_DWC3_GADGET is not set
# CONFIG_USB_DWC3_DUAL_ROLE is not set

#
# Platform Glue Driver Support
#
CONFIG_USB_DWC3_OMAP=m
CONFIG_USB_DWC3_EXYNOS=m
CONFIG_USB_DWC3_PCI=m

#
# Debugging features
#
# CONFIG_USB_DWC3_DEBUG is not set
# CONFIG_USB_CHIPIDEA is not set

#
# USB port drivers
#
CONFIG_USB_SERIAL=m
# CONFIG_USB_SERIAL_GENERIC is not set
# CONFIG_USB_SERIAL_SIMPLE is not set
# CONFIG_USB_SERIAL_AIRCABLE is not set
# CONFIG_USB_SERIAL_ARK3116 is not set
# CONFIG_USB_SERIAL_BELKIN is not set
# CONFIG_USB_SERIAL_CH341 is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
# CONFIG_USB_SERIAL_CP210X is not set
# CONFIG_USB_SERIAL_CYPRESS_M8 is not set
# CONFIG_USB_SERIAL_EMPEG is not set
# CONFIG_USB_SERIAL_FTDI_SIO is not set
# CONFIG_USB_SERIAL_VISOR is not set
# CONFIG_USB_SERIAL_IPAQ is not set
# CONFIG_USB_SERIAL_IR is not set
# CONFIG_USB_SERIAL_EDGEPORT is not set
# CONFIG_USB_SERIAL_EDGEPORT_TI is not set
# CONFIG_USB_SERIAL_F81232 is not set
# CONFIG_USB_SERIAL_GARMIN is not set
# CONFIG_USB_SERIAL_IPW is not set
# CONFIG_USB_SERIAL_IUU is not set
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
# CONFIG_USB_SERIAL_KEYSPAN is not set
# CONFIG_USB_SERIAL_KLSI is not set
# CONFIG_USB_SERIAL_KOBIL_SCT is not set
# CONFIG_USB_SERIAL_MCT_U232 is not set
# CONFIG_USB_SERIAL_METRO is not set
# CONFIG_USB_SERIAL_MOS7720 is not set
# CONFIG_USB_SERIAL_MOS7840 is not set
# CONFIG_USB_SERIAL_NAVMAN is not set
# CONFIG_USB_SERIAL_PL2303 is not set
# CONFIG_USB_SERIAL_OTI6858 is not set
# CONFIG_USB_SERIAL_QCAUX is not set
CONFIG_USB_SERIAL_QUALCOMM=m
# CONFIG_USB_SERIAL_SPCP8X5 is not set
# CONFIG_USB_SERIAL_SAFE is not set
# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set
# CONFIG_USB_SERIAL_SYMBOL is not set
# CONFIG_USB_SERIAL_TI is not set
# CONFIG_USB_SERIAL_CYBERJACK is not set
# CONFIG_USB_SERIAL_XIRCOM is not set
CONFIG_USB_SERIAL_WWAN=m
CONFIG_USB_SERIAL_OPTION=m
# CONFIG_USB_SERIAL_OMNINET is not set
# CONFIG_USB_SERIAL_OPTICON is not set
# CONFIG_USB_SERIAL_XSENS_MT is not set
# CONFIG_USB_SERIAL_WISHBONE is not set
# CONFIG_USB_SERIAL_ZTE is not set
# CONFIG_USB_SERIAL_SSU100 is not set
# CONFIG_USB_SERIAL_QT2 is not set
# CONFIG_USB_SERIAL_DEBUG is not set

#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_SEVSEG is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
CONFIG_USB_TEST=m
# CONFIG_USB_EHSET_TEST_FIXTURE is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_YUREX is not set
# CONFIG_USB_EZUSB_FX2 is not set
# CONFIG_USB_HSIC_USB3503 is not set

#
# USB Physical Layer drivers
#
CONFIG_USB_PHY=y
CONFIG_NOP_USB_XCEIV=y
# CONFIG_AM335X_PHY_USB is not set
# CONFIG_SAMSUNG_USB2PHY is not set
# CONFIG_SAMSUNG_USB3PHY is not set
# CONFIG_USB_GPIO_VBUS is not set
# CONFIG_USB_ISP1301 is not set
# CONFIG_USB_RCAR_PHY is not set
# CONFIG_USB_ULPI is not set
CONFIG_USB_GADGET=y
# CONFIG_USB_GADGET_DEBUG is not set
CONFIG_USB_GADGET_DEBUG_FILES=y
CONFIG_USB_GADGET_DEBUG_FS=y
CONFIG_USB_GADGET_VBUS_DRAW=2
CONFIG_USB_GADGET_STORAGE_NUM_BUFFERS=2

#
# USB Peripheral Controller
#
# CONFIG_USB_FUSB300 is not set
# CONFIG_USB_FOTG210_UDC is not set
# CONFIG_USB_R8A66597 is not set
# CONFIG_USB_PXA27X is not set
# CONFIG_USB_MV_UDC is not set
# CONFIG_USB_MV_U3D is not set
# CONFIG_USB_M66592 is not set
# CONFIG_USB_AMD5536UDC is not set
# CONFIG_USB_NET2272 is not set
# CONFIG_USB_NET2280 is not set
# CONFIG_USB_GOKU is not set
# CONFIG_USB_EG20T is not set
# CONFIG_USB_DUMMY_HCD is not set
CONFIG_USB_LIBCOMPOSITE=m
CONFIG_USB_F_ACM=m
CONFIG_USB_F_SS_LB=m
CONFIG_USB_U_SERIAL=m
CONFIG_USB_U_ETHER=m
CONFIG_USB_U_RNDIS=m
CONFIG_USB_F_ECM=m
CONFIG_USB_F_EEM=m
CONFIG_USB_F_SUBSET=m
CONFIG_USB_F_RNDIS=m
CONFIG_USB_F_MASS_STORAGE=m
# CONFIG_USB_CONFIGFS is not set
CONFIG_USB_ZERO=m
CONFIG_USB_ETH=m
CONFIG_USB_ETH_RNDIS=y
CONFIG_USB_ETH_EEM=y
# CONFIG_USB_G_NCM is not set
# CONFIG_USB_GADGETFS is not set
# CONFIG_USB_FUNCTIONFS is not set
CONFIG_USB_MASS_STORAGE=m
# CONFIG_USB_G_SERIAL is not set
# CONFIG_USB_G_PRINTER is not set
# CONFIG_USB_CDC_COMPOSITE is not set
# CONFIG_USB_G_ACM_MS is not set
CONFIG_USB_G_MULTI=m
CONFIG_USB_G_MULTI_RNDIS=y
CONFIG_USB_G_MULTI_CDC=y
# CONFIG_USB_G_HID is not set
# CONFIG_USB_G_DBGP is not set
# CONFIG_UWB is not set
CONFIG_MMC=y
# CONFIG_MMC_DEBUG is not set
CONFIG_MMC_UNSAFE_RESUME=y
# CONFIG_MMC_CLKGATE is not set

#
# MMC/SD/SDIO Card Drivers
#
CONFIG_MMC_BLOCK=y
CONFIG_MMC_BLOCK_MINORS=8
CONFIG_MMC_BLOCK_BOUNCE=y
CONFIG_SDIO_UART=y
# CONFIG_MMC_TEST is not set

#
# MMC/SD/SDIO Host Controller Drivers
#
# CONFIG_MMC_SDHCI is not set
# CONFIG_MMC_SDHCI_PXAV3 is not set
# CONFIG_MMC_SDHCI_PXAV2 is not set
CONFIG_MMC_OMAP=y
CONFIG_MMC_OMAP_HS=y
# CONFIG_MMC_TIFM_SD is not set
# CONFIG_MMC_CB710 is not set
# CONFIG_MMC_VIA_SDMMC is not set
# CONFIG_MMC_DW is not set
# CONFIG_MMC_VUB300 is not set
# CONFIG_MMC_USHC is not set
# CONFIG_MEMSTICK is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y

#
# LED drivers
#
# CONFIG_LEDS_LM3530 is not set
# CONFIG_LEDS_LM3642 is not set
# CONFIG_LEDS_PCA9532 is not set
CONFIG_LEDS_GPIO=y
# CONFIG_LEDS_LP3944 is not set
# CONFIG_LEDS_LP5521 is not set
# CONFIG_LEDS_LP5523 is not set
# CONFIG_LEDS_LP5562 is not set
# CONFIG_LEDS_LP8501 is not set
# CONFIG_LEDS_PCA955X is not set
# CONFIG_LEDS_PCA963X is not set
# CONFIG_LEDS_DAC124S085 is not set
# CONFIG_LEDS_REGULATOR is not set
# CONFIG_LEDS_BD2802 is not set
# CONFIG_LEDS_LT3593 is not set
# CONFIG_LEDS_TCA6507 is not set
# CONFIG_LEDS_LM355x is not set
# CONFIG_LEDS_OT200 is not set
# CONFIG_LEDS_BLINKM is not set

#
# LED Triggers
#
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_TIMER=y
CONFIG_LEDS_TRIGGER_ONESHOT=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
CONFIG_LEDS_TRIGGER_BACKLIGHT=y
CONFIG_LEDS_TRIGGER_CPU=y
CONFIG_LEDS_TRIGGER_GPIO=y
CONFIG_LEDS_TRIGGER_DEFAULT_ON=y

#
# iptables trigger is under Netfilter config (LED target)
#
# CONFIG_LEDS_TRIGGER_TRANSIENT is not set
# CONFIG_LEDS_TRIGGER_CAMERA is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
CONFIG_RTC_SYSTOHC=y
CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
# CONFIG_RTC_DEBUG is not set

#
# RTC interfaces
#
CONFIG_RTC_INTF_SYSFS=y
CONFIG_RTC_INTF_PROC=y
CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
# CONFIG_RTC_DRV_TEST is not set

#
# I2C RTC drivers
#
# CONFIG_RTC_DRV_DS1307 is not set
# CONFIG_RTC_DRV_DS1374 is not set
# CONFIG_RTC_DRV_DS1672 is not set
# CONFIG_RTC_DRV_DS3232 is not set
# CONFIG_RTC_DRV_MAX6900 is not set
# CONFIG_RTC_DRV_RS5C372 is not set
# CONFIG_RTC_DRV_ISL1208 is not set
# CONFIG_RTC_DRV_ISL12022 is not set
# CONFIG_RTC_DRV_X1205 is not set
CONFIG_RTC_DRV_PALMAS=y
# CONFIG_RTC_DRV_PCF2127 is not set
# CONFIG_RTC_DRV_PCF8523 is not set
# CONFIG_RTC_DRV_PCF8563 is not set
# CONFIG_RTC_DRV_PCF8583 is not set
CONFIG_RTC_DRV_M41T80=m
# CONFIG_RTC_DRV_M41T80_WDT is not set
# CONFIG_RTC_DRV_BQ32K is not set
CONFIG_RTC_DRV_TWL4030=y
# CONFIG_RTC_DRV_TPS65910 is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
# CONFIG_RTC_DRV_RX8025 is not set
# CONFIG_RTC_DRV_EM3027 is not set
# CONFIG_RTC_DRV_RV3029C2 is not set

#
# SPI RTC drivers
#
# CONFIG_RTC_DRV_M41T93 is not set
# CONFIG_RTC_DRV_M41T94 is not set
# CONFIG_RTC_DRV_DS1305 is not set
# CONFIG_RTC_DRV_DS1390 is not set
# CONFIG_RTC_DRV_MAX6902 is not set
# CONFIG_RTC_DRV_R9701 is not set
# CONFIG_RTC_DRV_RS5C348 is not set
# CONFIG_RTC_DRV_DS3234 is not set
# CONFIG_RTC_DRV_PCF2123 is not set
# CONFIG_RTC_DRV_RX4581 is not set

#
# Platform RTC drivers
#
# CONFIG_RTC_DRV_CMOS is not set
# CONFIG_RTC_DRV_DS1286 is not set
# CONFIG_RTC_DRV_DS1511 is not set
# CONFIG_RTC_DRV_DS1553 is not set
# CONFIG_RTC_DRV_DS1742 is not set
# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_M48T86 is not set
# CONFIG_RTC_DRV_M48T35 is not set
# CONFIG_RTC_DRV_M48T59 is not set
# CONFIG_RTC_DRV_MSM6242 is not set
# CONFIG_RTC_DRV_BQ4802 is not set
# CONFIG_RTC_DRV_RP5C01 is not set
# CONFIG_RTC_DRV_V3020 is not set
# CONFIG_RTC_DRV_DS2404 is not set

#
# on-CPU RTC drivers
#
CONFIG_RTC_DRV_OMAP=y
# CONFIG_RTC_DRV_SNVS is not set
# CONFIG_RTC_DRV_MOXART is not set

#
# HID Sensor RTC drivers
#
# CONFIG_RTC_DRV_HID_SENSOR_TIME is not set
CONFIG_DMADEVICES=y
# CONFIG_DMADEVICES_DEBUG is not set

#
# DMA Devices
#
# CONFIG_DW_DMAC_CORE is not set
# CONFIG_DW_DMAC is not set
# CONFIG_DW_DMAC_PCI is not set
# CONFIG_TIMB_DMA is not set
CONFIG_TI_EDMA=y
CONFIG_DMA_OMAP=y
# CONFIG_TI_CPPI41 is not set
CONFIG_DMA_ENGINE=y
CONFIG_DMA_VIRTUAL_CHANNELS=y
CONFIG_DMA_OF=y

#
# DMA Clients
#
# CONFIG_NET_DMA_DUMMY is not set
# CONFIG_ASYNC_TX_DMA is not set
# CONFIG_DMATEST is not set
# CONFIG_AUXDISPLAY is not set
# CONFIG_UIO is not set
# CONFIG_VIRT_DRIVERS is not set

#
# Virtio drivers
#
# CONFIG_VIRTIO_PCI is not set
# CONFIG_VIRTIO_MMIO is not set

#
# Microsoft Hyper-V guest support
#
CONFIG_STAGING=y
# CONFIG_ET131X is not set
# CONFIG_USBIP_CORE is not set
# CONFIG_ECHO is not set
# CONFIG_COMEDI is not set
# CONFIG_R8187SE is not set
# CONFIG_RTL8192U is not set
# CONFIG_RTLLIB is not set
# CONFIG_R8712U is not set
# CONFIG_R8188EU is not set
# CONFIG_RTS5139 is not set
# CONFIG_TRANZPORT is not set
# CONFIG_IDE_PHISON is not set
# CONFIG_USB_SERIAL_QUATECH2 is not set
# CONFIG_VT6655 is not set
# CONFIG_VT6656 is not set
# CONFIG_DX_SEP is not set
# CONFIG_ZSMALLOC is not set
# CONFIG_FB_SM7XX is not set
# CONFIG_CRYSTALHD is not set
# CONFIG_FB_XGI is not set
# CONFIG_USB_ENESTORAGE is not set
# CONFIG_BCM_WIMAX is not set
# CONFIG_FT1000 is not set

#
# Speakup console speech
#
# CONFIG_SPEAKUP is not set
# CONFIG_TOUCHSCREEN_CLEARPAD_TM1217 is not set
# CONFIG_TOUCHSCREEN_SYNAPTICS_I2C_RMI4 is not set
# CONFIG_STAGING_MEDIA is not set

#
# Android
#
# CONFIG_ANDROID is not set
# CONFIG_USB_WPAN_HCD is not set
# CONFIG_WIMAX_GDM72XX is not set
# CONFIG_LTE_GDM724X is not set
# CONFIG_NET_VENDOR_SILICOM is not set
# CONFIG_CED1401 is not set
# CONFIG_DGRP is not set
# CONFIG_USB_DWC2 is not set
# CONFIG_LUSTRE_FS is not set
# CONFIG_XILLYBUS is not set
# CONFIG_DGNC is not set
# CONFIG_DGAP is not set
CONFIG_CLKDEV_LOOKUP=y
CONFIG_HAVE_CLK_PREPARE=y
CONFIG_COMMON_CLK=y

#
# Common Clock Framework
#
# CONFIG_COMMON_CLK_DEBUG is not set
# CONFIG_COMMON_CLK_SI5351 is not set
# CONFIG_CLK_TWL6040 is not set
CONFIG_COMMON_CLK_PALMAS=y
CONFIG_HWSPINLOCK=y

#
# Hardware Spinlock drivers
#
CONFIG_HWSPINLOCK_OMAP=y
CONFIG_CLKSRC_OF=y
CONFIG_CLKSRC_MMIO=y
CONFIG_ARM_ARCH_TIMER=y
CONFIG_MAILBOX=y
CONFIG_OMAP_MBOX=y
CONFIG_OMAP2PLUS_MBOX=y
CONFIG_OMAP_MBOX_KFIFO_SIZE=256
CONFIG_IOMMU_SUPPORT=y
CONFIG_OF_IOMMU=y
# CONFIG_OMAP_IOMMU is not set

#
# Remoteproc drivers
#
# CONFIG_STE_MODEM_RPROC is not set

#
# Rpmsg drivers
#
# CONFIG_PM_DEVFREQ is not set
CONFIG_EXTCON=y

#
# Extcon Device Drivers
#
CONFIG_OF_EXTCON=y
# CONFIG_EXTCON_GPIO is not set
# CONFIG_EXTCON_PALMAS is not set
CONFIG_EXTCON_GPIO_USBVID=y
# CONFIG_MEMORY is not set
# CONFIG_IIO is not set
# CONFIG_VME_BUS is not set
# CONFIG_PWM is not set
CONFIG_IRQCHIP=y
CONFIG_ARM_GIC=y
# CONFIG_IPACK_BUS is not set
CONFIG_ARCH_HAS_RESET_CONTROLLER=y
CONFIG_RESET_CONTROLLER=y
CONFIG_RESET_TI=y
# CONFIG_FMC is not set

#
# PHY Subsystem
#
CONFIG_GENERIC_PHY=y
CONFIG_OMAP_CONTROL_PHY=m
CONFIG_OMAP_USB2=m
CONFIG_OMAP_PIPE3=m

#
# File systems
#
CONFIG_DCACHE_WORD_ACCESS=y
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_DEFAULTS_TO_ORDERED=y
CONFIG_EXT3_FS_XATTR=y
# CONFIG_EXT3_FS_POSIX_ACL is not set
# CONFIG_EXT3_FS_SECURITY is not set
CONFIG_EXT4_FS=y
# CONFIG_EXT4_FS_POSIX_ACL is not set
# CONFIG_EXT4_FS_SECURITY is not set
# CONFIG_EXT4_DEBUG is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_JBD2=y
# CONFIG_JBD2_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
# CONFIG_NILFS2_FS is not set
CONFIG_FS_POSIX_ACL=y
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_FANOTIFY is not set
CONFIG_QUOTA=y
# CONFIG_QUOTA_NETLINK_INTERFACE is not set
CONFIG_PRINT_QUOTA_WARNING=y
# CONFIG_QUOTA_DEBUG is not set
CONFIG_QUOTA_TREE=y
# CONFIG_QFMT_V1 is not set
CONFIG_QFMT_V2=y
CONFIG_QUOTACTL=y
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set

#
# Caches
#
# CONFIG_FSCACHE is not set

#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
# CONFIG_UDF_FS is not set

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
# CONFIG_NTFS_FS is not set

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_TMPFS_XATTR is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_CONFIGFS_FS=m
CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_ECRYPT_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
CONFIG_JFFS2_FS=y
CONFIG_JFFS2_FS_DEBUG=0
CONFIG_JFFS2_FS_WRITEBUFFER=y
# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
CONFIG_JFFS2_SUMMARY=y
CONFIG_JFFS2_FS_XATTR=y
CONFIG_JFFS2_FS_POSIX_ACL=y
CONFIG_JFFS2_FS_SECURITY=y
CONFIG_JFFS2_COMPRESSION_OPTIONS=y
CONFIG_JFFS2_ZLIB=y
CONFIG_JFFS2_LZO=y
CONFIG_JFFS2_RTIME=y
CONFIG_JFFS2_RUBIN=y
# CONFIG_JFFS2_CMODE_NONE is not set
CONFIG_JFFS2_CMODE_PRIORITY=y
# CONFIG_JFFS2_CMODE_SIZE is not set
# CONFIG_JFFS2_CMODE_FAVOURLZO is not set
CONFIG_UBIFS_FS=y
# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
CONFIG_UBIFS_FS_LZO=y
CONFIG_UBIFS_FS_ZLIB=y
# CONFIG_LOGFS is not set
CONFIG_CRAMFS=y
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_QNX6FS_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_PSTORE is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
# CONFIG_F2FS_FS is not set
# CONFIG_AUFS_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=m
CONFIG_NFS_V2=m
CONFIG_NFS_V3=m
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=m
# CONFIG_NFS_SWAP is not set
# CONFIG_NFS_V4_1 is not set
# CONFIG_NFS_USE_LEGACY_DNS is not set
CONFIG_NFS_USE_KERNEL_DNS=y
# CONFIG_NFSD is not set
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_NFS_ACL_SUPPORT=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=m
CONFIG_SUNRPC_GSS=m
# CONFIG_SUNRPC_DEBUG is not set
# CONFIG_CEPH_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ASCII is not set
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_MAC_ROMAN is not set
# CONFIG_NLS_MAC_CELTIC is not set
# CONFIG_NLS_MAC_CENTEURO is not set
# CONFIG_NLS_MAC_CROATIAN is not set
# CONFIG_NLS_MAC_CYRILLIC is not set
# CONFIG_NLS_MAC_GAELIC is not set
# CONFIG_NLS_MAC_GREEK is not set
# CONFIG_NLS_MAC_ICELAND is not set
# CONFIG_NLS_MAC_INUIT is not set
# CONFIG_NLS_MAC_ROMANIAN is not set
# CONFIG_NLS_MAC_TURKISH is not set
# CONFIG_NLS_UTF8 is not set
CONFIG_DLM=m
CONFIG_DLM_DEBUG=y

#
# Kernel hacking
#

#
# printk and dmesg options
#
CONFIG_PRINTK_TIME=y
CONFIG_DEFAULT_MESSAGE_LOGLEVEL=4
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_DYNAMIC_DEBUG is not set

#
# Compile-time checks and compiler options
#
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_INFO_REDUCED is not set
CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_READABLE_ASM is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_SECTION_MISMATCH is not set
# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
CONFIG_MAGIC_SYSRQ=y
CONFIG_MAGIC_SYSRQ_DEFAULT_MASK=0x1
# CONFIG_IPIPE_DEBUG is not set
CONFIG_DEBUG_KERNEL=y

#
# Memory Debugging
#
# CONFIG_DEBUG_PAGEALLOC is not set
# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_SLUB_DEBUG_ON is not set
# CONFIG_SLUB_STATS is not set
CONFIG_HAVE_DEBUG_KMEMLEAK=y
# CONFIG_DEBUG_KMEMLEAK is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_DEBUG_PER_CPU_MAPS is not set
# CONFIG_DEBUG_HIGHMEM is not set
# CONFIG_DEBUG_SHIRQ is not set

#
# Debug Lockups and Hangs
#
# CONFIG_LOCKUP_DETECTOR is not set
# CONFIG_DETECT_HUNG_TASK is not set
# CONFIG_PANIC_ON_OOPS is not set
CONFIG_PANIC_ON_OOPS_VALUE=0
CONFIG_SCHED_DEBUG=y
CONFIG_SCHEDSTATS=y
CONFIG_TIMER_STATS=y
CONFIG_DEBUG_PREEMPT=y

#
# Lock Debugging (spinlocks, mutexes, etc...)
#
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
CONFIG_DEBUG_SPINLOCK=y
CONFIG_DEBUG_MUTEXES=y
# CONFIG_DEBUG_WW_MUTEX_SLOWPATH is not set
CONFIG_DEBUG_LOCK_ALLOC=y
CONFIG_PROVE_LOCKING=y
CONFIG_LOCKDEP=y
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_LOCKDEP is not set
# CONFIG_DEBUG_ATOMIC_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
CONFIG_TRACE_IRQFLAGS=y
CONFIG_STACKTRACE=y
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_WRITECOUNT is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
# CONFIG_DEBUG_CREDENTIALS is not set

#
# RCU Debugging
#
# CONFIG_PROVE_RCU is not set
# CONFIG_PROVE_RCU_DELAY is not set
# CONFIG_SPARSE_RCU_POINTER is not set
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_RCU_CPU_STALL_TIMEOUT=21
CONFIG_RCU_CPU_STALL_VERBOSE=y
# CONFIG_RCU_CPU_STALL_INFO is not set
# CONFIG_RCU_TRACE is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
# CONFIG_NOTIFIER_ERROR_INJECTION is not set
# CONFIG_FAULT_INJECTION is not set
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_HAVE_C_RECORDMCOUNT=y
CONFIG_TRACE_CLOCK=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_IRQSOFF_TRACER is not set
# CONFIG_PREEMPT_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_ENABLE_DEFAULT_TRACERS is not set
# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_TRACER_SNAPSHOT is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
# CONFIG_PROFILE_ALL_BRANCHES is not set
# CONFIG_STACK_TRACER is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
CONFIG_KPROBE_EVENT=y
CONFIG_PROBE_EVENTS=y
# CONFIG_RING_BUFFER_BENCHMARK is not set
# CONFIG_RING_BUFFER_STARTUP_TEST is not set

#
# Runtime Testing
#
# CONFIG_LKDTM is not set
# CONFIG_TEST_LIST_SORT is not set
# CONFIG_KPROBES_SANITY_TEST is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_RBTREE_TEST is not set
# CONFIG_INTERVAL_TREE_TEST is not set
# CONFIG_ATOMIC64_SELFTEST is not set
# CONFIG_TEST_STRING_HELPERS is not set
# CONFIG_TEST_KSTRTOX is not set
# CONFIG_DMA_API_DEBUG is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
# CONFIG_STRICT_DEVMEM is not set
CONFIG_ARM_UNWIND=y
CONFIG_DEBUG_USER=y
# CONFIG_DEBUG_LL is not set
CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
# CONFIG_DEBUG_UART_PL01X is not set
# CONFIG_DEBUG_UART_8250 is not set
CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
# CONFIG_ARM_KPROBES_TEST is not set
# CONFIG_PID_IN_CONTEXTIDR is not set

#
# Security options
#
CONFIG_KEYS=y
# CONFIG_ENCRYPTED_KEYS is not set
# CONFIG_KEYS_DEBUG_PROC_KEYS is not set
# CONFIG_SECURITY_DMESG_RESTRICT is not set
CONFIG_SECURITY=y
# CONFIG_SECURITYFS is not set
CONFIG_SECURITY_NETWORK=y
CONFIG_SECURITY_NETWORK_XFRM=y
# CONFIG_SECURITY_PATH is not set
# CONFIG_SECURITY_SMACK is not set
# CONFIG_SECURITY_TOMOYO is not set
# CONFIG_SECURITY_APPARMOR is not set
# CONFIG_SECURITY_YAMA is not set
# CONFIG_IMA is not set
# CONFIG_EVM is not set
CONFIG_DEFAULT_SECURITY_DAC=y
CONFIG_DEFAULT_SECURITY=""
CONFIG_CRYPTO=y

#
# Crypto core or helper
#
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD=m
CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_BLKCIPHER=m
CONFIG_CRYPTO_BLKCIPHER2=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_HASH2=y
CONFIG_CRYPTO_RNG=m
CONFIG_CRYPTO_RNG2=y
CONFIG_CRYPTO_PCOMP=m
CONFIG_CRYPTO_PCOMP2=y
CONFIG_CRYPTO_MANAGER=m
CONFIG_CRYPTO_MANAGER2=y
# CONFIG_CRYPTO_USER is not set
CONFIG_CRYPTO_MANAGER_DISABLE_TESTS=y
CONFIG_CRYPTO_GF128MUL=m
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_PCRYPT=m
CONFIG_CRYPTO_WORKQUEUE=y
CONFIG_CRYPTO_CRYPTD=m
CONFIG_CRYPTO_AUTHENC=m
# CONFIG_CRYPTO_TEST is not set

#
# Authenticated Encryption with Associated Data
#
CONFIG_CRYPTO_CCM=m
CONFIG_CRYPTO_GCM=m
CONFIG_CRYPTO_SEQIV=m

#
# Block modes
#
CONFIG_CRYPTO_CBC=m
CONFIG_CRYPTO_CTR=m
# CONFIG_CRYPTO_CTS is not set
CONFIG_CRYPTO_ECB=m
# CONFIG_CRYPTO_LRW is not set
# CONFIG_CRYPTO_PCBC is not set
# CONFIG_CRYPTO_XTS is not set

#
# Hash modes
#
CONFIG_CRYPTO_CMAC=m
CONFIG_CRYPTO_HMAC=m
# CONFIG_CRYPTO_XCBC is not set
# CONFIG_CRYPTO_VMAC is not set

#
# Digest
#
CONFIG_CRYPTO_CRC32C=y
CONFIG_CRYPTO_CRC32=m
CONFIG_CRYPTO_CRCT10DIF=y
CONFIG_CRYPTO_GHASH=m
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=m
CONFIG_CRYPTO_MICHAEL_MIC=y
# CONFIG_CRYPTO_RMD128 is not set
# CONFIG_CRYPTO_RMD160 is not set
# CONFIG_CRYPTO_RMD256 is not set
# CONFIG_CRYPTO_RMD320 is not set
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA1_ARM=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_CRYPTO_TGR192 is not set
# CONFIG_CRYPTO_WP512 is not set

#
# Ciphers
#
CONFIG_CRYPTO_AES=y
CONFIG_CRYPTO_AES_ARM=m
# CONFIG_CRYPTO_ANUBIS is not set
CONFIG_CRYPTO_ARC4=m
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_CAMELLIA is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
CONFIG_CRYPTO_DES=m
# CONFIG_CRYPTO_FCRYPT is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_SALSA20 is not set
# CONFIG_CRYPTO_SEED is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_TEA is not set
# CONFIG_CRYPTO_TWOFISH is not set

#
# Compression
#
CONFIG_CRYPTO_DEFLATE=y
CONFIG_CRYPTO_ZLIB=m
CONFIG_CRYPTO_LZO=y
CONFIG_CRYPTO_LZ4=m
CONFIG_CRYPTO_LZ4HC=m

#
# Random Number Generation
#
CONFIG_CRYPTO_ANSI_CPRNG=m
CONFIG_CRYPTO_USER_API=m
CONFIG_CRYPTO_USER_API_HASH=m
CONFIG_CRYPTO_USER_API_SKCIPHER=m
CONFIG_CRYPTO_HW=y
# CONFIG_CRYPTO_DEV_HIFN_795X is not set
CONFIG_CRYPTO_DEV_OMAP_SHAM=m
CONFIG_CRYPTO_DEV_OMAP_AES=m
CONFIG_CRYPTO_DEV_OMAP_DES=m
# CONFIG_ASYMMETRIC_KEY_TYPE is not set
CONFIG_BINARY_PRINTF=y

#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_GENERIC_STRNCPY_FROM_USER=y
CONFIG_GENERIC_STRNLEN_USER=y
CONFIG_GENERIC_NET_UTILS=y
CONFIG_GENERIC_PCI_IOMAP=y
CONFIG_GENERIC_IO=y
CONFIG_CRC_CCITT=y
CONFIG_CRC16=y
CONFIG_CRC_T10DIF=y
CONFIG_CRC_ITU_T=y
CONFIG_CRC32=y
# CONFIG_CRC32_SELFTEST is not set
CONFIG_CRC32_SLICEBY8=y
# CONFIG_CRC32_SLICEBY4 is not set
# CONFIG_CRC32_SARWATE is not set
# CONFIG_CRC32_BIT is not set
CONFIG_CRC7=y
CONFIG_LIBCRC32C=y
# CONFIG_CRC8 is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_LZO_COMPRESS=y
CONFIG_LZO_DECOMPRESS=y
CONFIG_LZ4_COMPRESS=m
CONFIG_LZ4HC_COMPRESS=m
CONFIG_LZ4_DECOMPRESS=m
# CONFIG_XZ_DEC is not set
# CONFIG_XZ_DEC_BCJ is not set
CONFIG_DECOMPRESS_GZIP=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_CPU_RMAP=y
CONFIG_DQL=y
CONFIG_NLATTR=y
CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
CONFIG_AVERAGE=y
CONFIG_CORDIC=m
# CONFIG_DDR is not set
CONFIG_OID_REGISTRY=m
CONFIG_FONT_SUPPORT=y
CONFIG_FONTS=y
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
# CONFIG_FONT_6x11 is not set
# CONFIG_FONT_7x14 is not set
# CONFIG_FONT_PEARL_8x8 is not set
# CONFIG_FONT_ACORN_8x8 is not set
# CONFIG_FONT_MINI_4x6 is not set
# CONFIG_FONT_SUN8x16 is not set
# CONFIG_FONT_SUN12x22 is not set
# CONFIG_FONT_10x18 is not set
# CONFIG_VIRTUALIZATION is not set

^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 21:59                             ` Lennart Sorensen
@ 2014-03-31 22:04                               ` Lennart Sorensen
  2014-03-31 22:11                                 ` Gilles Chanteperdrix
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-03-31 22:04 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Mon, Mar 31, 2014 at 05:59:33PM -0400, Lennart Sorensen wrote:
> On Mon, Mar 31, 2014 at 05:53:48PM -0400, Lennart Sorensen wrote:
> > I am using the xenomai-2.6 git tree (current commit I see is as HEAD is
> > 4081e1b032329bf0cc9442f466233d5fc1083fc5).
> > 
> > Doing a git pull I see I am 4 commits behind, and one does sound
> > interesting.  I will have to update that.
> 
> Hmm, the interesting patch does the same thing I already did myself to
> get it to compile.  I guess that is OK then.

Hmm, gdb is being not helpful at all:

root@omap5:/mnt/xenomai-2.6.3# gdb /usr/lib/xenomai/testsuite/latency 
GNU gdb (GDB) 7.4.1-debian
Copyright (C) 2012 Free Software Foundation, Inc.
License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html>
This is free software: you are free to change and redistribute it.
There is NO WARRANTY, to the extent permitted by law.  Type "show copying"
and "show warranty" for details.
This GDB was configured as "arm-linux-gnueabihf".
For bug reporting instructions, please see:
<http://www.gnu.org/software/gdb/bugs/>...
Reading symbols from /usr/lib/xenomai/testsuite/latency...done.
(gdb) run
Starting program: /usr/lib/xenomai/testsuite/latency 
[Thread debugging using libthread_db enabled]
Using host libthread_db library "/lib/arm-linux-gnueabihf/libthread_db.so.1".
== Sampling period: 1000 us
== Test mode: periodic user-mode task
== All results in microseconds
[New Thread 0xb6e15470 (LWP 32035)]
[New Thread 0xb6e0d470 (LWP 32036)]
warming up...

Program received signal SIGILL, Illegal instruction.
[Switching to Thread 0xb6e0d470 (LWP 32036)]
0xffff0f04 in ?? ()
(gdb) where
#0  0xffff0f04 in ?? ()
Cannot access memory at address 0x3e0
(gdb) list
Cannot access memory at address 0x3e0
(gdb) 

-- 
Len Sorensen

^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 22:04                               ` Lennart Sorensen
@ 2014-03-31 22:11                                 ` Gilles Chanteperdrix
  2014-03-31 22:27                                   ` Gilles Chanteperdrix
  0 siblings, 1 reply; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-03-31 22:11 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 04/01/2014 12:04 AM, Lennart Sorensen wrote:
> On Mon, Mar 31, 2014 at 05:59:33PM -0400, Lennart Sorensen wrote:
>> On Mon, Mar 31, 2014 at 05:53:48PM -0400, Lennart Sorensen wrote:
>>> I am using the xenomai-2.6 git tree (current commit I see is as HEAD is
>>> 4081e1b032329bf0cc9442f466233d5fc1083fc5).
>>>
>>> Doing a git pull I see I am 4 commits behind, and one does sound
>>> interesting.  I will have to update that.
>>
>> Hmm, the interesting patch does the same thing I already did myself to
>> get it to compile.  I guess that is OK then.
> 
> Hmm, gdb is being not helpful at all:
> 
> root@omap5:/mnt/xenomai-2.6.3# gdb /usr/lib/xenomai/testsuite/latency 
> GNU gdb (GDB) 7.4.1-debian
> Copyright (C) 2012 Free Software Foundation, Inc.
> License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html>
> This is free software: you are free to change and redistribute it.
> There is NO WARRANTY, to the extent permitted by law.  Type "show copying"
> and "show warranty" for details.
> This GDB was configured as "arm-linux-gnueabihf".
> For bug reporting instructions, please see:
> <http://www.gnu.org/software/gdb/bugs/>...
> Reading symbols from /usr/lib/xenomai/testsuite/latency...done.
> (gdb) run
> Starting program: /usr/lib/xenomai/testsuite/latency 
> [Thread debugging using libthread_db enabled]
> Using host libthread_db library "/lib/arm-linux-gnueabihf/libthread_db.so.1".
> == Sampling period: 1000 us
> == Test mode: periodic user-mode task
> == All results in microseconds
> [New Thread 0xb6e15470 (LWP 32035)]
> [New Thread 0xb6e0d470 (LWP 32036)]
> warming up...
> 
> Program received signal SIGILL, Illegal instruction.
> [Switching to Thread 0xb6e0d470 (LWP 32036)]
> 0xffff0f04 in ?? ()
> (gdb) where
> #0  0xffff0f04 in ?? ()
> Cannot access memory at address 0x3e0
> (gdb) list
> Cannot access memory at address 0x3e0
> (gdb) 
> 

0xffff0f04 looks like one of the kuser helpers. It is the I-pipe tsc
emulation address actually. You probably do not have access to the
architected timers in user-space. There is a snippet in
drivers/clocksource/arm_arch_timer.c to enable this access through the
CNTKCTL register. Maybe this only enables access to physical counter
whereas newer kernels use virtual counters?

-- 
                                                                Gilles.


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 22:11                                 ` Gilles Chanteperdrix
@ 2014-03-31 22:27                                   ` Gilles Chanteperdrix
  2014-04-01  1:32                                     ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-03-31 22:27 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 04/01/2014 12:11 AM, Gilles Chanteperdrix wrote:
> On 04/01/2014 12:04 AM, Lennart Sorensen wrote:
>> On Mon, Mar 31, 2014 at 05:59:33PM -0400, Lennart Sorensen wrote:
>>> On Mon, Mar 31, 2014 at 05:53:48PM -0400, Lennart Sorensen wrote:
>>>> I am using the xenomai-2.6 git tree (current commit I see is as HEAD is
>>>> 4081e1b032329bf0cc9442f466233d5fc1083fc5).
>>>>
>>>> Doing a git pull I see I am 4 commits behind, and one does sound
>>>> interesting.  I will have to update that.
>>>
>>> Hmm, the interesting patch does the same thing I already did myself to
>>> get it to compile.  I guess that is OK then.
>>
>> Hmm, gdb is being not helpful at all:
>>
>> root@omap5:/mnt/xenomai-2.6.3# gdb /usr/lib/xenomai/testsuite/latency 
>> GNU gdb (GDB) 7.4.1-debian
>> Copyright (C) 2012 Free Software Foundation, Inc.
>> License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html>
>> This is free software: you are free to change and redistribute it.
>> There is NO WARRANTY, to the extent permitted by law.  Type "show copying"
>> and "show warranty" for details.
>> This GDB was configured as "arm-linux-gnueabihf".
>> For bug reporting instructions, please see:
>> <http://www.gnu.org/software/gdb/bugs/>...
>> Reading symbols from /usr/lib/xenomai/testsuite/latency...done.
>> (gdb) run
>> Starting program: /usr/lib/xenomai/testsuite/latency 
>> [Thread debugging using libthread_db enabled]
>> Using host libthread_db library "/lib/arm-linux-gnueabihf/libthread_db.so.1".
>> == Sampling period: 1000 us
>> == Test mode: periodic user-mode task
>> == All results in microseconds
>> [New Thread 0xb6e15470 (LWP 32035)]
>> [New Thread 0xb6e0d470 (LWP 32036)]
>> warming up...
>>
>> Program received signal SIGILL, Illegal instruction.
>> [Switching to Thread 0xb6e0d470 (LWP 32036)]
>> 0xffff0f04 in ?? ()
>> (gdb) where
>> #0  0xffff0f04 in ?? ()
>> Cannot access memory at address 0x3e0
>> (gdb) list
>> Cannot access memory at address 0x3e0
>> (gdb) 
>>
> 
> 0xffff0f04 looks like one of the kuser helpers. It is the I-pipe tsc
> emulation address actually. You probably do not have access to the
> architected timers in user-space. There is a snippet in
> drivers/clocksource/arm_arch_timer.c to enable this access through the
> CNTKCTL register. Maybe this only enables access to physical counter
> whereas newer kernels use virtual counters?
> 
Ok, arch_counter_set_user_access disables user access to the 
architected timer counter. The following patch should avoid this:

diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index b605f04e..7aea949 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -374,7 +374,9 @@ static int arch_timer_setup(struct clock_event_device *clk)
 			enable_percpu_irq(arch_timer_ppi[PHYS_NONSECURE_PPI], 0);
 	}
 
+#ifndef CONFIG_IPIPE
 	arch_counter_set_user_access();
+#endif
 
 	return 0;
 }


-- 
                                                                Gilles.


^ permalink raw reply related	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 22:27                                   ` Gilles Chanteperdrix
@ 2014-04-01  1:32                                     ` Lennart Sorensen
  2014-04-01 10:52                                       ` Gilles Chanteperdrix
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-04-01  1:32 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Tue, Apr 01, 2014 at 12:27:45AM +0200, Gilles Chanteperdrix wrote:
> Ok, arch_counter_set_user_access disables user access to the 
> architected timer counter. The following patch should avoid this:
> 
> diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
> index b605f04e..7aea949 100644
> --- a/drivers/clocksource/arm_arch_timer.c
> +++ b/drivers/clocksource/arm_arch_timer.c
> @@ -374,7 +374,9 @@ static int arch_timer_setup(struct clock_event_device *clk)
>  			enable_percpu_irq(arch_timer_ppi[PHYS_NONSECURE_PPI], 0);
>  	}
>  
> +#ifndef CONFIG_IPIPE
>  	arch_counter_set_user_access();
> +#endif
>  
>  	return 0;
>  }

That might have taken me a while to track down.  Excellent work.

root@omap5:~# /usr/lib/xenomai/testsuite/latency 
== Sampling period: 1000 us
== Test mode: periodic user-mode task
== All results in microseconds
warming up...
RTT|  00:00:01  (periodic user-mode task, 1000 us period, priority 99)
RTH|----lat min|----lat avg|----lat max|-overrun|---msw|---lat best|--lat worst
RTD|     -0.163|      0.488|      3.743|       0|     0|     -0.163|      3.743
RTD|     -0.652|      0.000|      3.092|       0|     0|     -0.652|      3.743
RTD|     -0.652|      0.000|      2.929|       0|     0|     -0.652|      3.743
RTD|     -0.652|      0.000|      2.929|       0|     0|     -0.652|      3.743
RTD|     -0.652|      0.325|      3.255|       0|     0|     -0.652|      3.743
RTD|     -0.652|      0.000|      2.929|       0|     0|     -0.652|      3.743
RTD|     -0.489|      0.162|      3.743|       0|     0|     -0.652|      3.743
RTD|     -0.652|      0.000|      2.929|       0|     0|     -0.652|      3.743
RTD|     -0.652|      0.000|      3.092|       0|     0|     -0.652|      3.743
RTD|     -0.652|      0.325|      3.906|       0|     0|     -0.652|      3.906
RTD|     -0.652|      0.000|      3.255|       0|     0|     -0.652|      3.906
RTD|     -0.652|      0.000|      2.278|       0|     0|     -0.652|      3.906
RTD|     -2.442|      0.000|      2.604|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.162|      3.255|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.325|      3.092|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.000|      3.255|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.000|      2.929|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.000|      3.743|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.000|      2.929|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.325|      3.417|       0|     0|     -2.442|      3.906
RTD|     -1.954|      0.000|      3.255|       0|     0|     -2.442|      3.906
RTT|  00:00:22  (periodic user-mode task, 1000 us period, priority 99)
RTH|----lat min|----lat avg|----lat max|-overrun|---msw|---lat best|--lat worst
RTD|     -0.652|      0.000|      2.929|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.000|      2.766|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.000|      2.766|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.325|      3.092|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.000|      2.766|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.000|      2.929|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.000|      3.092|       0|     0|     -2.442|      3.906
RTD|     -1.465|      0.000|      2.929|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.325|      3.580|       0|     0|     -2.442|      3.906
RTD|     -1.628|      0.000|      3.092|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.000|      2.929|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.000|      2.766|       0|     0|     -2.442|      3.906
RTD|     -0.652|      0.000|      3.092|       0|     0|     -2.442|      3.906
RTD|     -0.489|      0.325|      4.231|       0|     0|     -2.442|      4.231
RTD|     -0.652|      0.000|      3.580|       0|     0|     -2.442|      4.231
RTD|     -0.652|      0.000|      2.766|       0|     0|     -2.442|      4.231
RTD|     -0.652|      0.000|      2.604|       0|     0|     -2.442|      4.231
RTD|     -1.303|      0.000|      3.417|       0|     0|     -2.442|      4.231
RTD|     -0.652|      0.325|      3.743|       0|     0|     -2.442|      4.231
RTD|     -1.954|      0.000|      2.929|       0|     0|     -2.442|      4.231
RTD|     -0.652|      0.000|      2.441|       0|     0|     -2.442|      4.231
RTT|  00:00:43  (periodic user-mode task, 1000 us period, priority 99)
RTH|----lat min|----lat avg|----lat max|-overrun|---msw|---lat best|--lat worst
RTD|     -0.652|      0.000|      2.929|       0|     0|     -2.442|      4.231
RTD|     -0.652|      0.000|      2.929|       0|     0|     -2.442|      4.231
RTD|     -0.652|      0.325|      3.417|       0|     0|     -2.442|      4.231
RTD|     -0.652|      0.000|      2.604|       0|     0|     -2.442|      4.231
RTD|     -0.652|      0.000|      2.929|       0|     0|     -2.442|      4.231
RTD|     -0.652|      0.000|      3.092|       0|     0|     -2.442|      4.231
^C---|-----------|-----------|-----------|--------|------|-------------------------
RTS|     -2.442|      0.000|      4.231|       0|     0|    00:00:48/00:00:48

mutex torture tests now pass, cond tests pass, most things seem to pass,
but I think the failing ones need either modules enabled I didn't enable,
or maybe special hardware.

Any recommended way to test if things are really working now?

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-01  1:32                                     ` Lennart Sorensen
@ 2014-04-01 10:52                                       ` Gilles Chanteperdrix
  2014-04-01 13:12                                         ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-04-01 10:52 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 04/01/2014 03:32 AM, Lennart Sorensen wrote:
> On Tue, Apr 01, 2014 at 12:27:45AM +0200, Gilles Chanteperdrix wrote:
>> Ok, arch_counter_set_user_access disables user access to the 
>> architected timer counter. The following patch should avoid this:
>>
>> diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
>> index b605f04e..7aea949 100644
>> --- a/drivers/clocksource/arm_arch_timer.c
>> +++ b/drivers/clocksource/arm_arch_timer.c
>> @@ -374,7 +374,9 @@ static int arch_timer_setup(struct clock_event_device *clk)
>>  			enable_percpu_irq(arch_timer_ppi[PHYS_NONSECURE_PPI], 0);
>>  	}
>>  
>> +#ifndef CONFIG_IPIPE
>>  	arch_counter_set_user_access();
>> +#endif
>>  
>>  	return 0;
>>  }
> 
> That might have taken me a while to track down.  Excellent work.
> 
> root@omap5:~# /usr/lib/xenomai/testsuite/latency 
> == Sampling period: 1000 us
> == Test mode: periodic user-mode task
> == All results in microseconds
> warming up...
> RTT|  00:00:01  (periodic user-mode task, 1000 us period, priority 99)
> RTH|----lat min|----lat avg|----lat max|-overrun|---msw|---lat best|--lat worst
> RTD|     -0.163|      0.488|      3.743|       0|     0|     -0.163|      3.743
> RTD|     -0.652|      0.000|      3.092|       0|     0|     -0.652|      3.743
> RTD|     -0.652|      0.000|      2.929|       0|     0|     -0.652|      3.743
> RTD|     -0.652|      0.000|      2.929|       0|     0|     -0.652|      3.743
> RTD|     -0.652|      0.325|      3.255|       0|     0|     -0.652|      3.743
> RTD|     -0.652|      0.000|      2.929|       0|     0|     -0.652|      3.743
> RTD|     -0.489|      0.162|      3.743|       0|     0|     -0.652|      3.743
> RTD|     -0.652|      0.000|      2.929|       0|     0|     -0.652|      3.743
> RTD|     -0.652|      0.000|      3.092|       0|     0|     -0.652|      3.743
> RTD|     -0.652|      0.325|      3.906|       0|     0|     -0.652|      3.906
> RTD|     -0.652|      0.000|      3.255|       0|     0|     -0.652|      3.906
> RTD|     -0.652|      0.000|      2.278|       0|     0|     -0.652|      3.906
> RTD|     -2.442|      0.000|      2.604|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.162|      3.255|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.325|      3.092|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.000|      3.255|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.000|      2.929|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.000|      3.743|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.000|      2.929|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.325|      3.417|       0|     0|     -2.442|      3.906
> RTD|     -1.954|      0.000|      3.255|       0|     0|     -2.442|      3.906
> RTT|  00:00:22  (periodic user-mode task, 1000 us period, priority 99)
> RTH|----lat min|----lat avg|----lat max|-overrun|---msw|---lat best|--lat worst
> RTD|     -0.652|      0.000|      2.929|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.000|      2.766|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.000|      2.766|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.325|      3.092|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.000|      2.766|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.000|      2.929|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.000|      3.092|       0|     0|     -2.442|      3.906
> RTD|     -1.465|      0.000|      2.929|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.325|      3.580|       0|     0|     -2.442|      3.906
> RTD|     -1.628|      0.000|      3.092|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.000|      2.929|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.000|      2.766|       0|     0|     -2.442|      3.906
> RTD|     -0.652|      0.000|      3.092|       0|     0|     -2.442|      3.906
> RTD|     -0.489|      0.325|      4.231|       0|     0|     -2.442|      4.231
> RTD|     -0.652|      0.000|      3.580|       0|     0|     -2.442|      4.231
> RTD|     -0.652|      0.000|      2.766|       0|     0|     -2.442|      4.231
> RTD|     -0.652|      0.000|      2.604|       0|     0|     -2.442|      4.231
> RTD|     -1.303|      0.000|      3.417|       0|     0|     -2.442|      4.231
> RTD|     -0.652|      0.325|      3.743|       0|     0|     -2.442|      4.231
> RTD|     -1.954|      0.000|      2.929|       0|     0|     -2.442|      4.231
> RTD|     -0.652|      0.000|      2.441|       0|     0|     -2.442|      4.231
> RTT|  00:00:43  (periodic user-mode task, 1000 us period, priority 99)
> RTH|----lat min|----lat avg|----lat max|-overrun|---msw|---lat best|--lat worst
> RTD|     -0.652|      0.000|      2.929|       0|     0|     -2.442|      4.231
> RTD|     -0.652|      0.000|      2.929|       0|     0|     -2.442|      4.231
> RTD|     -0.652|      0.325|      3.417|       0|     0|     -2.442|      4.231
> RTD|     -0.652|      0.000|      2.604|       0|     0|     -2.442|      4.231
> RTD|     -0.652|      0.000|      2.929|       0|     0|     -2.442|      4.231
> RTD|     -0.652|      0.000|      3.092|       0|     0|     -2.442|      4.231
> ^C---|-----------|-----------|-----------|--------|------|-------------------------
> RTS|     -2.442|      0.000|      4.231|       0|     0|    00:00:48/00:00:48
> 
> mutex torture tests now pass, cond tests pass, most things seem to pass,
> but I think the failing ones need either modules enabled I didn't enable,
> or maybe special hardware.
> 
> Any recommended way to test if things are really working now?
> 
The way I test it is by running xeno-regression-test, using dohell with
LTP to create a load. Note that the latency result given by
xeno-regression-test should not be taken into account as switchtest is
running concurrently and creates large non-preemptible sections,
xeno-regression-test is more a stress test.

-- 
                                                                Gilles.


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-01 10:52                                       ` Gilles Chanteperdrix
@ 2014-04-01 13:12                                         ` Lennart Sorensen
  2014-04-01 19:35                                           ` Gilles Chanteperdrix
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-04-01 13:12 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Tue, Apr 01, 2014 at 12:52:44PM +0200, Gilles Chanteperdrix wrote:
> The way I test it is by running xeno-regression-test, using dohell with
> LTP to create a load. Note that the latency result given by
> xeno-regression-test should not be taken into account as switchtest is
> running concurrently and creates large non-preemptible sections,
> xeno-regression-test is more a stress test.

I will see if I can find the invocation to run that then.

I let cyclictest, switchtest and latency running the last 8 hours,
and latency test currently says:

RTD|     -0.814|      2.441|      7.486|       0|     0|     -2.116|     20.182

That seems decent at least.

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-01 13:12                                         ` Lennart Sorensen
@ 2014-04-01 19:35                                           ` Gilles Chanteperdrix
  2014-04-01 19:40                                             ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-04-01 19:35 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 04/01/2014 03:12 PM, Lennart Sorensen wrote:
> On Tue, Apr 01, 2014 at 12:52:44PM +0200, Gilles Chanteperdrix wrote:
>> The way I test it is by running xeno-regression-test, using dohell with
>> LTP to create a load. Note that the latency result given by
>> xeno-regression-test should not be taken into account as switchtest is
>> running concurrently and creates large non-preemptible sections,
>> xeno-regression-test is more a stress test.
> 
> I will see if I can find the invocation to run that then.
> 
> I let cyclictest, switchtest and latency running the last 8 hours,
> and latency test currently says:
> 
> RTD|     -0.814|      2.441|      7.486|       0|     0|     -2.116|     20.182
> 
> That seems decent at least.
> 

I use:
xeno-regression-test -l "dohell -s 192.168.0.5 -m /mnt -l /ltp"

Where the machine with ip 192.168.0.5 has the "discard" service enabled
(port 9, available in inetd), an usb key is mounted on /mnt, and LTP is
installed in /ltp.

-- 
                                                                Gilles.


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-01 19:35                                           ` Gilles Chanteperdrix
@ 2014-04-01 19:40                                             ` Lennart Sorensen
  2014-04-01 20:52                                               ` Gilles Chanteperdrix
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-04-01 19:40 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Tue, Apr 01, 2014 at 09:35:24PM +0200, Gilles Chanteperdrix wrote:
> On 04/01/2014 03:12 PM, Lennart Sorensen wrote:
> > On Tue, Apr 01, 2014 at 12:52:44PM +0200, Gilles Chanteperdrix wrote:
> >> The way I test it is by running xeno-regression-test, using dohell with
> >> LTP to create a load. Note that the latency result given by
> >> xeno-regression-test should not be taken into account as switchtest is
> >> running concurrently and creates large non-preemptible sections,
> >> xeno-regression-test is more a stress test.
> > 
> > I will see if I can find the invocation to run that then.
> > 
> > I let cyclictest, switchtest and latency running the last 8 hours,
> > and latency test currently says:
> > 
> > RTD|     -0.814|      2.441|      7.486|       0|     0|     -2.116|     20.182
> > 
> > That seems decent at least.
> > 
> 
> I use:
> xeno-regression-test -l "dohell -s 192.168.0.5 -m /mnt -l /ltp"
> 
> Where the machine with ip 192.168.0.5 has the "discard" service enabled
> (port 9, available in inetd), an usb key is mounted on /mnt, and LTP is
> installed in /ltp.

I get an error when I use the -s option.

I ran out of space, so ltp is instaled on the usb key mounted at /mnt.
Hopefully it won't mind that.

++ /usr/lib/xenomai/testsuite/regression/posix/xddp_test
FAILURE xddp_test.c:41: socket(AF_RTIPC, SOCK_DGRAM, IPCPROTO_XDDP): Address family not supported by protocol

Maybe I am mising a kernel config.

Does this look normal for the start:

root@omap5:~# xeno-regression-test xeno-regression-test -l "dohell -s 10.200.19.25 -m /mnt -l /mnt" -t 2 
Started child 14119: /bin/bash /usr/lib/xenomai/testsuite/xeno-test-run-wrapper /usr/bin/xeno-regression-test xeno-regression-test -l dohell -s 10.200.19.25 -m /mnt -l /mnt -t 2
++ echo 0
++ /usr/lib/xenomai/testsuite/arith
mul: 0x79364d93, shft: 26
integ: 30, frac: 0x4d9364d9364d9364

signed positive operation: 0x03ffffffffffffff * 1000000000 / 33000000
inline calibration: 0x0000000000000000: 0.000 ns, rejected 9999/10000
inlined llimd: 0x79364d9364d9362f: 1141.959 ns, rejected 19/10000
inlined llmulshft: 0x79364d92ffffffe1: 0.000 ns, rejected 9999/10000
inlined nodiv_llimd: 0x79364d9364d9362f: 0.000 ns, rejected 9999/10000
out of line calibration: 0x0000000000000000: 81.380 ns, rejected 9998/10000
out of line llimd: 0x79364d9364d9362f: 1056.477 ns, rejected 15/10000
out of line llmulshft: 0x79364d92ffffffe1: -81.380 ns, rejected 9999/10000
out of line nodiv_llimd: 0x79364d9364d9362f: -81.380 ns, rejected 9999/10000

signed negative operation: 0xfc00000000000001 * 1000000000 / 33000000
inline calibration: 0x0000000000000000: 0.000 ns, rejected 9999/10000
inlined llimd: 0x86c9b26c9b26c9d1: 1138.427 ns, rejected 25/10000
inlined llmulshft: 0x86c9b26d0000001e: 0.000 ns, rejected 9999/10000
inlined nodiv_llimd: 0x86c9b26c9b26c9d1: 81.380 ns, rejected 9998/10000
out of line calibration: 0x0000000000000000: 81.380 ns, rejected 9998/10000
out of line llimd: 0x86c9b26c9b26c9d1: 1073.095 ns, rejected 17/10000
out of line llmulshft: 0x86c9b26d0000001e: -81.380 ns, rejected 9999/10000
out of line nodiv_llimd: 0x86c9b26c9b26c9d1: -81.380 ns, rejected 9999/10000

unsigned operation: 0x03ffffffffffffff * 1000000000 / 33000000
inline calibration: 0x0000000000000000: 0.000 ns, rejected 9999/10000
inlined nodiv_ullimd: 0x79364d9364d9362f: 81.380 ns, rejected 9998/10000
out of line calibration: 0x0000000000000000: 81.380 ns, rejected 9998/10000
out of line nodiv_ullimd: 0x79364d9364d9362f: -81.380 ns, rejected 9999/10000
++ /usr/lib/xenomai/testsuite/clocktest -C 42 -T 30
== Tested clock: 42 (CLOCK_HOST_REALTIME)
CPU      ToD offset [us] ToD drift [us/s]      warps max delta [us]
--- -------------------- ---------------- ---------- --------------
  0                  1.0           -0.014          0            0.0
  1                  1.1           -0.007          0            0.0
++ /usr/lib/xenomai/testsuite/clocktest -T 30
== Tested clock: 0 (CLOCK_REALTIME)
CPU      ToD offset [us] ToD drift [us/s]      warps max delta [us]
--- -------------------- ---------------- ---------- --------------
  0           38290685.4          681.125          0            0.0
  1           38290685.7          681.130          0            0.0
++ /usr/lib/xenomai/testsuite/cond-torture-native
simple_condwait
relative_condwait
absolute_condwait
sig_norestart_condwait
sig_restart_condwait
sig_norestart_condwait_mutex
sig_restart_condwait_mutex
sig_norestart_double
sig_restart_double
cond_destroy_whilewait
Test OK
++ /usr/lib/xenomai/testsuite/cond-torture-posix
simple_condwait
relative_condwait
absolute_condwait
sig_norestart_condwait
sig_restart_condwait
sig_norestart_condwait_mutex
sig_restart_condwait_mutex
sig_norestart_double
sig_restart_double
cond_destroy_whilewait
Test OK
++ /usr/lib/xenomai/testsuite/mutex-torture-native
simple_wait
recursive_wait
timed_mutex
mode_switch
pi_wait
lock_stealing
NOTE: lock_stealing mutex_trylock: not supported
deny_stealing
simple_condwait
recursive_condwait
auto_switchback
Test OK
++ /usr/lib/xenomai/testsuite/mutex-torture-posix
simple_wait
recursive_wait
errorcheck_wait
timed_mutex
mode_switch
pi_wait
lock_stealing
NOTE: lock_stealing mutex_trylock: not supported
deny_stealing
simple_condwait
recursive_condwait
auto_switchback
Test OK
++ /usr/lib/xenomai/testsuite/regression/posix/leaks
Checking for leaks in posix skin objects
thread: OK
mutex: OK
cond: OK
sem: OK
named sem: OK
timer: OK
shm: OK
mq: OK
++ /usr/lib/xenomai/testsuite/regression/posix/mprotect
memory read
memory write after exec enable
memory write after write enable
memory read/write after access enable
Test OK
++ /usr/lib/xenomai/testsuite/regression/posix/nano_test
Test OK
++ /usr/lib/xenomai/testsuite/regression/posix/shm
Checking posix skin shared memories
posix skin shared memories: success
++ /usr/lib/xenomai/testsuite/regression/posix/xddp_test
FAILURE xddp_test.c:41: socket(AF_RTIPC, SOCK_DGRAM, IPCPROTO_XDDP): Address family not supported by protocol


-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-01 19:40                                             ` Lennart Sorensen
@ 2014-04-01 20:52                                               ` Gilles Chanteperdrix
  2014-04-01 21:45                                                 ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-04-01 20:52 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 04/01/2014 09:40 PM, Lennart Sorensen wrote:
> On Tue, Apr 01, 2014 at 09:35:24PM +0200, Gilles Chanteperdrix wrote:
>> On 04/01/2014 03:12 PM, Lennart Sorensen wrote:
>>> On Tue, Apr 01, 2014 at 12:52:44PM +0200, Gilles Chanteperdrix wrote:
>>>> The way I test it is by running xeno-regression-test, using dohell with
>>>> LTP to create a load. Note that the latency result given by
>>>> xeno-regression-test should not be taken into account as switchtest is
>>>> running concurrently and creates large non-preemptible sections,
>>>> xeno-regression-test is more a stress test.
>>>
>>> I will see if I can find the invocation to run that then.
>>>
>>> I let cyclictest, switchtest and latency running the last 8 hours,
>>> and latency test currently says:
>>>
>>> RTD|     -0.814|      2.441|      7.486|       0|     0|     -2.116|     20.182
>>>
>>> That seems decent at least.
>>>
>>
>> I use:
>> xeno-regression-test -l "dohell -s 192.168.0.5 -m /mnt -l /ltp"
>>
>> Where the machine with ip 192.168.0.5 has the "discard" service enabled
>> (port 9, available in inetd), an usb key is mounted on /mnt, and LTP is
>> installed in /ltp.
> 
> I get an error when I use the -s option.

Probably because the machine with the IP address you pass after -s does
not have the "discard" service enabled in inetd.conf

> 
> I ran out of space, so ltp is instaled on the usb key mounted at /mnt.
> Hopefully it won't mind that.
> 
> ++ /usr/lib/xenomai/testsuite/regression/posix/xddp_test
> FAILURE xddp_test.c:41: socket(AF_RTIPC, SOCK_DGRAM, IPCPROTO_XDDP): Address family not supported by protocol

> 
> Maybe I am mising a kernel config.

Well, you need to enable xddp.

-- 
                                                                Gilles.


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-01 20:52                                               ` Gilles Chanteperdrix
@ 2014-04-01 21:45                                                 ` Lennart Sorensen
  2014-04-01 22:01                                                   ` Gilles Chanteperdrix
  2014-04-02  2:35                                                   ` Lennart Sorensen
  0 siblings, 2 replies; 45+ messages in thread
From: Lennart Sorensen @ 2014-04-01 21:45 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Tue, Apr 01, 2014 at 10:52:31PM +0200, Gilles Chanteperdrix wrote:
> On 04/01/2014 09:40 PM, Lennart Sorensen wrote:
> > On Tue, Apr 01, 2014 at 09:35:24PM +0200, Gilles Chanteperdrix wrote:
> >> On 04/01/2014 03:12 PM, Lennart Sorensen wrote:
> >>> On Tue, Apr 01, 2014 at 12:52:44PM +0200, Gilles Chanteperdrix wrote:
> >>>> The way I test it is by running xeno-regression-test, using dohell with
> >>>> LTP to create a load. Note that the latency result given by
> >>>> xeno-regression-test should not be taken into account as switchtest is
> >>>> running concurrently and creates large non-preemptible sections,
> >>>> xeno-regression-test is more a stress test.
> >>>
> >>> I will see if I can find the invocation to run that then.
> >>>
> >>> I let cyclictest, switchtest and latency running the last 8 hours,
> >>> and latency test currently says:
> >>>
> >>> RTD|     -0.814|      2.441|      7.486|       0|     0|     -2.116|     20.182
> >>>
> >>> That seems decent at least.
> >>>
> >>
> >> I use:
> >> xeno-regression-test -l "dohell -s 192.168.0.5 -m /mnt -l /ltp"
> >>
> >> Where the machine with ip 192.168.0.5 has the "discard" service enabled
> >> (port 9, available in inetd), an usb key is mounted on /mnt, and LTP is
> >> installed in /ltp.
> > 
> > I get an error when I use the -s option.
> 
> Probably because the machine with the IP address you pass after -s does
> not have the "discard" service enabled in inetd.conf

I thought I had.

root@omap5:~# grep RTIPC /boot/config-3.12-1-dra7xx 
CONFIG_XENO_DRIVERS_RTIPC=m
CONFIG_XENO_DRIVERS_RTIPC_XDDP=y
CONFIG_XENO_DRIVERS_RTIPC_IDDP=y
CONFIG_XENO_DRIVERS_RTIPC_BUFP=y

Maybe I forgot to load the module....  Yep that was it.

Then I got to this:

Started child 14296: /usr/lib/xenomai/testsuite/latency xeno-regression-test -l dohell -s 10.200.19.25 -m /mnt -l /mnt -t 2
/usr/lib/xenomai/testsuite/latency: invalid option -- 'm'
usage: latency [options]
  [-h]                         # print histograms of min, avg, max latencies
  [-g <file>]                  # dump histogram to <file> in gnuplot format
  [-s]                         # print statistics of min, avg, max latencies
  [-H <histogram-size>]        # default = 200, increase if your last bucket is full
  [-B <bucket-size>]           # default = 1000ns, decrease for more resolution
  [-p <period_us>]             # sampling period
  [-l <data-lines per header>] # default=21, 0 to supress headers
  [-T <test_duration_seconds>] # default=0, so ^C to end
  [-q]                         # supresses RTD, RTH lines if -T is used
  [-D <testing_device_no>]     # number of testing device, default=0
  [-t <test_mode>]             # 0=user task (default), 1=kernel task, 2=timer IRQ
  [-f]                         # freeze trace for each new max latency
  [-c <cpu>]                   # pin measuring task down to given CPU
  [-P <priority>]              # task priority (test mode 0 and 1 only)
  [-b]                         # break upon mode switch
== Testing FPU check routines...
d0: 1 != 2
d1: 1 != 2
d2: 1 != 2
d3: 1 != 2
d4: 1 != 2
d5: 1 != 2
d6: 1 != 2
d7: 1 != 2
d8: 1 != 2
d9: 1 != 2
d10: 1 != 2
d11: 1 != 2
d12: 1 != 2
d13: 1 != 2
d14: 1 != 2
d15: 1 != 2
== FPU check routines: OK.
== Testing FPU check routines...
d0: 1 != 2
d1: 1 != 2
d2: 1 != 2
d3: 1 != 2
d4: 1 != 2
d5: 1 != 2
d6: 1 != 2
d7: 1 != 2
d8: 1 != 2
d9: 1 != 2
d10: 1 != 2
d11: 1 != 2
d12: 1 != 2
d13: 1 != 2
d14: 1 != 2
d15: 1 != 2
== FPU check routines: OK.
/usr/bin/xeno-regression-test failed: child 14296 exited with status 2

I was running:

xeno-regression-test xeno-regression-test -l "dohell -s 10.200.19.25 -m /mnt -l /mnt" -t 2

Maybe I got something wrong.

ltp is installed to /mnt (which is a USB stick).

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-01 21:45                                                 ` Lennart Sorensen
@ 2014-04-01 22:01                                                   ` Gilles Chanteperdrix
  2014-04-02  2:35                                                   ` Lennart Sorensen
  1 sibling, 0 replies; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-04-01 22:01 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 04/01/2014 11:45 PM, Lennart Sorensen wrote:
> On Tue, Apr 01, 2014 at 10:52:31PM +0200, Gilles Chanteperdrix wrote:
>> On 04/01/2014 09:40 PM, Lennart Sorensen wrote:
>>> On Tue, Apr 01, 2014 at 09:35:24PM +0200, Gilles Chanteperdrix wrote:
>>>> On 04/01/2014 03:12 PM, Lennart Sorensen wrote:
>>>>> On Tue, Apr 01, 2014 at 12:52:44PM +0200, Gilles Chanteperdrix wrote:
>>>>>> The way I test it is by running xeno-regression-test, using dohell with
>>>>>> LTP to create a load. Note that the latency result given by
>>>>>> xeno-regression-test should not be taken into account as switchtest is
>>>>>> running concurrently and creates large non-preemptible sections,
>>>>>> xeno-regression-test is more a stress test.
>>>>>
>>>>> I will see if I can find the invocation to run that then.
>>>>>
>>>>> I let cyclictest, switchtest and latency running the last 8 hours,
>>>>> and latency test currently says:
>>>>>
>>>>> RTD|     -0.814|      2.441|      7.486|       0|     0|     -2.116|     20.182
>>>>>
>>>>> That seems decent at least.
>>>>>
>>>>
>>>> I use:
>>>> xeno-regression-test -l "dohell -s 192.168.0.5 -m /mnt -l /ltp"
>>>>
>>>> Where the machine with ip 192.168.0.5 has the "discard" service enabled
>>>> (port 9, available in inetd), an usb key is mounted on /mnt, and LTP is
>>>> installed in /ltp.
>>>
>>> I get an error when I use the -s option.
>>
>> Probably because the machine with the IP address you pass after -s does
>> not have the "discard" service enabled in inetd.conf
> 
> I thought I had.

Do you have the nc command available?

> 
> root@omap5:~# grep RTIPC /boot/config-3.12-1-dra7xx 
> CONFIG_XENO_DRIVERS_RTIPC=m
> CONFIG_XENO_DRIVERS_RTIPC_XDDP=y
> CONFIG_XENO_DRIVERS_RTIPC_IDDP=y
> CONFIG_XENO_DRIVERS_RTIPC_BUFP=y
> 
> Maybe I forgot to load the module....  Yep that was it.
> 
> Then I got to this:
> 
> Started child 14296: /usr/lib/xenomai/testsuite/latency xeno-regression-test -l dohell -s 10.200.19.25 -m /mnt -l /mnt -t 2

I woud say you forgot the quotes around the dohell command, so the -m
option gets passed to latency instead of dohell.

-- 
                                                                Gilles.


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-01 21:45                                                 ` Lennart Sorensen
  2014-04-01 22:01                                                   ` Gilles Chanteperdrix
@ 2014-04-02  2:35                                                   ` Lennart Sorensen
  2014-04-02  7:11                                                     ` Gilles Chanteperdrix
  1 sibling, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-04-02  2:35 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Tue, Apr 01, 2014 at 05:45:39PM -0400, Lennart Sorensen wrote:
> I was running:
> 
> xeno-regression-test xeno-regression-test -l "dohell -s 10.200.19.25 -m /mnt -l /mnt" -t 2

These quotes are in the wrong place?

I cut and paste the line from:

t@omap5:~# xeno-regression-test --help
Started child 23870: /bin/bash /usr/lib/xenomai/testsuite/xeno-test-run-wrapper /usr/bin/xeno-regression-test --help
xeno-regression-test [ -l "load command" ] [ -- ] [ latency test options ]

Run Xenomai regression testsuite on your platform, by first starting a
fewtests, then running the latency test in parallel to the switchtest test
under the load generated by "load-command".

By default, the load command is "dohell 900", which will generate load during
15 minutes. To generate a more realistic load see dohell help.

Any other option passed on the command line is passed to the latency test.

Example:
xeno-regression-test -l "dohell -s 192.168.0.5 -m /mnt -l /ltp" -t 2

Will generate load including network load using the server at IP address
192.168.0.5, some I/O under the moint point /mnt, and the LTP testsuite
installed under the /ltp directory, and use the latency test by measuring the
timer irq latency.

......

All I changed was the -l option, which I changed to the location I
installed ltp to.

Maybe xeno-regression-test is broken.  Maybe it assumes /bin/sh is bash
or something.

-- 
Len Sorensen

^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-02  2:35                                                   ` Lennart Sorensen
@ 2014-04-02  7:11                                                     ` Gilles Chanteperdrix
  2014-04-02 13:24                                                       ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-04-02  7:11 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 04/02/2014 04:35 AM, Lennart Sorensen wrote:
> All I changed was the -l option, which I changed to the location I
> installed ltp to.
> 
> Maybe xeno-regression-test is broken.  Maybe it assumes /bin/sh is bash
> or something.
> 
I am using this command with ash (busybox shell) without any problem.
Parsing these quotes is done by the interactive shell you are running,
not xeno-regression-test itself.

-- 
                                                                Gilles.


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-02  7:11                                                     ` Gilles Chanteperdrix
@ 2014-04-02 13:24                                                       ` Lennart Sorensen
  2014-04-02 13:26                                                         ` Gilles Chanteperdrix
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-04-02 13:24 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Wed, Apr 02, 2014 at 09:11:59AM +0200, Gilles Chanteperdrix wrote:
> On 04/02/2014 04:35 AM, Lennart Sorensen wrote:
> > All I changed was the -l option, which I changed to the location I
> > installed ltp to.
> > 
> > Maybe xeno-regression-test is broken.  Maybe it assumes /bin/sh is bash
> > or something.
> > 
> I am using this command with ash (busybox shell) without any problem.
> Parsing these quotes is done by the interactive shell you are running,
> not xeno-regression-test itself.

This is the line that is causing issues as far as I can tell.

check_alive /usr/lib/xenomai/testsuite/latency ${1+"$@"}

So it is passing all the original arguments to latency for some reason,
and latency has no idea what -m is supposed to mean.

On Debian /bin/sh is dash, which is a pure posix shell.  If it isn't
posix, it isn't valid.  checkbashisms doesn't seem to think there is
anything wrong with that line though.

As far as this shows I think the quotes were right:

select service with posix message queues: success
++ start_load
++ echo start_load
++ check_alive /usr/lib/xenomai/testsuite/switchtest
++ echo check_alive /usr/lib/xenomai/testsuite/switchtest
++ check_alive /usr/lib/xenomai/testsuite/switchtest -s 1000
++ echo check_alive /usr/lib/xenomai/testsuite/switchtest -s 1000
++ check_alive /usr/lib/xenomai/testsuite/latency xeno-regression-test -l '/usr/lib/xenomai/testsuite/dohell -s 10.200.19.25 -m /mnt -l /mnt' -t 2
++ echo check_alive /usr/lib/xenomai/testsuite/latency xeno-regression-test -l '/usr/lib/xenomai/testsuite/dohell -s 10.200.19.25 -m /mnt -l /mnt' -t 2
++ wait_load
++ read rc
Started child 13475: dohell 900
Started child 13476: /usr/lib/xenomai/testsuite/switchtest
Started child 13481: /usr/lib/xenomai/testsuite/switchtest -s 1000
Started child 13484: /usr/lib/xenomai/testsuite/latency xeno-regression-test -l /usr/lib/xenomai/testsuite/dohell -s 10.200.19.25 -m /mnt -l /mnt -t 2
/usr/lib/xenomai/testsuite/latency: invalid option -- 'm'
usage: latency [options]
  [-h]                         # print histograms of min, avg, max latencies
  [-g <file>]                  # dump histogram to <file> in gnuplot format
  [-s]                         # print statistics of min, avg, max latencies
  [-H <histogram-size>]        # default = 200, increase if your last bucket is full
  [-B <bucket-size>]           # default = 1000ns, decrease for more resolution
  [-p <period_us>]             # sampling period
  [-l <data-lines per header>] # default=21, 0 to supress headers
  [-T <test_duration_seconds>] # default=0, so ^C to end
  [-q]                         # supresses RTD, RTH lines if -T is used
  [-D <testing_device_no>]     # number of testing device, default=0
  [-t <test_mode>]             # 0=user task (default), 1=kernel task, 2=timer IRQ
  [-f]                         # freeze trace for each new max latency
  [-c <cpu>]                   # pin measuring task down to given CPU
  [-P <priority>]              # task priority (test mode 0 and 1 only)
  [-b]                         # break upon mode switch

I just don't see what the point of passing $1 and company to the latency
test is.  It looks as if the -t 2 was supposed to go to the latency
test, and it looks as if the -l argument was ignored since it seems to
be running dohell 900 (the default) instead.

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-02 13:24                                                       ` Lennart Sorensen
@ 2014-04-02 13:26                                                         ` Gilles Chanteperdrix
  2014-04-02 13:40                                                           ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-04-02 13:26 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 04/02/2014 03:24 PM, Lennart Sorensen wrote:
> On Wed, Apr 02, 2014 at 09:11:59AM +0200, Gilles Chanteperdrix wrote:
>> On 04/02/2014 04:35 AM, Lennart Sorensen wrote:
>>> All I changed was the -l option, which I changed to the location I
>>> installed ltp to.
>>>
>>> Maybe xeno-regression-test is broken.  Maybe it assumes /bin/sh is bash
>>> or something.
>>>
>> I am using this command with ash (busybox shell) without any problem.
>> Parsing these quotes is done by the interactive shell you are running,
>> not xeno-regression-test itself.
>
> This is the line that is causing issues as far as I can tell.
>
> check_alive /usr/lib/xenomai/testsuite/latency ${1+"$@"}
>
> So it is passing all the original arguments to latency for some reason,
> and latency has no idea what -m is supposed to mean.
>
> On Debian /bin/sh is dash, which is a pure posix shell.  If it isn't
> posix, it isn't valid.  checkbashisms doesn't seem to think there is
> anything wrong with that line though.
>
> As far as this shows I think the quotes were right:

xeno-regression-test does not take into account your -l option, since it 
is using dohell 900 as load, instead of the line you specified. Are you 
sure you did not mix-up -1 and -l ?


-- 
					    Gilles.


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-02 13:26                                                         ` Gilles Chanteperdrix
@ 2014-04-02 13:40                                                           ` Lennart Sorensen
  2014-04-02 13:41                                                             ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-04-02 13:40 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Wed, Apr 02, 2014 at 03:26:34PM +0200, Gilles Chanteperdrix wrote:
> On 04/02/2014 03:24 PM, Lennart Sorensen wrote:
> >On Wed, Apr 02, 2014 at 09:11:59AM +0200, Gilles Chanteperdrix wrote:
> >>On 04/02/2014 04:35 AM, Lennart Sorensen wrote:
> >>>All I changed was the -l option, which I changed to the location I
> >>>installed ltp to.
> >>>
> >>>Maybe xeno-regression-test is broken.  Maybe it assumes /bin/sh is bash
> >>>or something.
> >>>
> >>I am using this command with ash (busybox shell) without any problem.
> >>Parsing these quotes is done by the interactive shell you are running,
> >>not xeno-regression-test itself.
> >
> >This is the line that is causing issues as far as I can tell.
> >
> >check_alive /usr/lib/xenomai/testsuite/latency ${1+"$@"}
> >
> >So it is passing all the original arguments to latency for some reason,
> >and latency has no idea what -m is supposed to mean.
> >
> >On Debian /bin/sh is dash, which is a pure posix shell.  If it isn't
> >posix, it isn't valid.  checkbashisms doesn't seem to think there is
> >anything wrong with that line though.
> >
> >As far as this shows I think the quotes were right:
> 
> xeno-regression-test does not take into account your -l option,
> since it is using dohell 900 as load, instead of the line you
> specified. Are you sure you did not mix-up -1 and -l ?

I just checked.  argv2 = xeno-regresstion-test, not -l.  WTF?

I am investigating how that is even remotely possible.

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-02 13:40                                                           ` Lennart Sorensen
@ 2014-04-02 13:41                                                             ` Lennart Sorensen
  2014-04-02 13:46                                                               ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-04-02 13:41 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Wed, Apr 02, 2014 at 09:40:18AM -0400, Lennart Sorensen wrote:
> On Wed, Apr 02, 2014 at 03:26:34PM +0200, Gilles Chanteperdrix wrote:
> > On 04/02/2014 03:24 PM, Lennart Sorensen wrote:
> > >On Wed, Apr 02, 2014 at 09:11:59AM +0200, Gilles Chanteperdrix wrote:
> > >>On 04/02/2014 04:35 AM, Lennart Sorensen wrote:
> > >>>All I changed was the -l option, which I changed to the location I
> > >>>installed ltp to.
> > >>>
> > >>>Maybe xeno-regression-test is broken.  Maybe it assumes /bin/sh is bash
> > >>>or something.
> > >>>
> > >>I am using this command with ash (busybox shell) without any problem.
> > >>Parsing these quotes is done by the interactive shell you are running,
> > >>not xeno-regression-test itself.
> > >
> > >This is the line that is causing issues as far as I can tell.
> > >
> > >check_alive /usr/lib/xenomai/testsuite/latency ${1+"$@"}
> > >
> > >So it is passing all the original arguments to latency for some reason,
> > >and latency has no idea what -m is supposed to mean.
> > >
> > >On Debian /bin/sh is dash, which is a pure posix shell.  If it isn't
> > >posix, it isn't valid.  checkbashisms doesn't seem to think there is
> > >anything wrong with that line though.
> > >
> > >As far as this shows I think the quotes were right:
> > 
> > xeno-regression-test does not take into account your -l option,
> > since it is using dohell 900 as load, instead of the line you
> > specified. Are you sure you did not mix-up -1 and -l ?
> 
> I just checked.  argv2 = xeno-regresstion-test, not -l.  WTF?
> 
> I am investigating how that is even remotely possible.

Here is the argv array it is getting:

argv=[/usr/lib/xenomai/testsuite/xeno-test-run][/usr/bin/xeno-regression-test][xeno-regression-test][-l][/usr/lib/xenomai/testsuite/dohell -s 10.200.19.25 -m /mnt -l /mnt]

No wonder it isn't working.

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-02 13:41                                                             ` Lennart Sorensen
@ 2014-04-02 13:46                                                               ` Lennart Sorensen
  2014-04-02 13:56                                                                 ` Gilles Chanteperdrix
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-04-02 13:46 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Wed, Apr 02, 2014 at 09:41:34AM -0400, Lennart Sorensen wrote:
> Here is the argv array it is getting:
> 
> argv=[/usr/lib/xenomai/testsuite/xeno-test-run][/usr/bin/xeno-regression-test][xeno-regression-test][-l][/usr/lib/xenomai/testsuite/dohell -s 10.200.19.25 -m /mnt -l /mnt]
> 
> No wonder it isn't working.

Found it.  it can happen when the user isn't capable of operating cut and paste:

root@omap5:/mnt/xenomai-2.6.3# xeno-regression-test xeno-regression-test -l "/usr/lib/xenomai/testsuite/dohell -s 10.200.19.25 -m /mnt -l /mnt" -t 2

Lets try fixing that shall we...

And now it runs... Yay!

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-02 13:46                                                               ` Lennart Sorensen
@ 2014-04-02 13:56                                                                 ` Gilles Chanteperdrix
  2014-04-02 14:38                                                                   ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-04-02 13:56 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 04/02/2014 03:46 PM, Lennart Sorensen wrote:
> On Wed, Apr 02, 2014 at 09:41:34AM -0400, Lennart Sorensen wrote:
>> Here is the argv array it is getting:
>>
>> argv=[/usr/lib/xenomai/testsuite/xeno-test-run][/usr/bin/xeno-regression-test][xeno-regression-test][-l][/usr/lib/xenomai/testsuite/dohell -s 10.200.19.25 -m /mnt -l /mnt]
>>
>> No wonder it isn't working.
>
> Found it.  it can happen when the user isn't capable of operating cut and paste:
>
> root@omap5:/mnt/xenomai-2.6.3# xeno-regression-test xeno-regression-test -l "/usr/lib/xenomai/testsuite/dohell -s 10.200.19.25 -m /mnt -l /mnt" -t 2
>
> Lets try fixing that shall we...

PEBKAC then. Ok, -t 2 measures the irq latency, it may not be what you want.

-- 
					    Gilles.


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-02 13:56                                                                 ` Gilles Chanteperdrix
@ 2014-04-02 14:38                                                                   ` Lennart Sorensen
  2014-04-02 14:41                                                                     ` Gilles Chanteperdrix
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-04-02 14:38 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Wed, Apr 02, 2014 at 03:56:25PM +0200, Gilles Chanteperdrix wrote:
> On 04/02/2014 03:46 PM, Lennart Sorensen wrote:
> >On Wed, Apr 02, 2014 at 09:41:34AM -0400, Lennart Sorensen wrote:
> >>Here is the argv array it is getting:
> >>
> >>argv=[/usr/lib/xenomai/testsuite/xeno-test-run][/usr/bin/xeno-regression-test][xeno-regression-test][-l][/usr/lib/xenomai/testsuite/dohell -s 10.200.19.25 -m /mnt -l /mnt]
> >>
> >>No wonder it isn't working.
> >
> >Found it.  it can happen when the user isn't capable of operating cut and paste:
> >
> >root@omap5:/mnt/xenomai-2.6.3# xeno-regression-test xeno-regression-test -l "/usr/lib/xenomai/testsuite/dohell -s 10.200.19.25 -m /mnt -l /mnt" -t 2
> >
> >Lets try fixing that shall we...
> 
> PEBKAC then. Ok, -t 2 measures the irq latency, it may not be what you want.

I don't know what I want.  I just wanted to run something to check
xenomai is actually working.

It would appear it is.

So is there a time this test will run for or do I have to kill it at
some point?

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-02 14:38                                                                   ` Lennart Sorensen
@ 2014-04-02 14:41                                                                     ` Gilles Chanteperdrix
  2014-04-03 13:46                                                                       ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-04-02 14:41 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 04/02/2014 04:38 PM, Lennart Sorensen wrote:
> On Wed, Apr 02, 2014 at 03:56:25PM +0200, Gilles Chanteperdrix wrote:
>> On 04/02/2014 03:46 PM, Lennart Sorensen wrote:
>>> On Wed, Apr 02, 2014 at 09:41:34AM -0400, Lennart Sorensen wrote:
>>>> Here is the argv array it is getting:
>>>>
>>>> argv=[/usr/lib/xenomai/testsuite/xeno-test-run][/usr/bin/xeno-regression-test][xeno-regression-test][-l][/usr/lib/xenomai/testsuite/dohell -s 10.200.19.25 -m /mnt -l /mnt]
>>>>
>>>> No wonder it isn't working.
>>>
>>> Found it.  it can happen when the user isn't capable of operating cut and paste:
>>>
>>> root@omap5:/mnt/xenomai-2.6.3# xeno-regression-test xeno-regression-test -l "/usr/lib/xenomai/testsuite/dohell -s 10.200.19.25 -m /mnt -l /mnt" -t 2
>>>
>>> Lets try fixing that shall we...
>>
>> PEBKAC then. Ok, -t 2 measures the irq latency, it may not be what you want.
>
> I don't know what I want.  I just wanted to run something to check
> xenomai is actually working.
>
> It would appear it is.
>
> So is there a time this test will run for or do I have to kill it at
> some point?
>
It will run the whole LTP testsuite twice, this should last a few hours. 
If one test gets stuck (like mallocstress with some versions of gcc), 
simply kill it, and LTP will continue. I have been running a modified 
version of LTP 2008 since, well, 2008, and have reinstalled a more 
recent version only recently and did not test if the changes I made over 
time to the 2008 version were still needed.

-- 
					    Gilles.


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-02 14:41                                                                     ` Gilles Chanteperdrix
@ 2014-04-03 13:46                                                                       ` Lennart Sorensen
  2014-04-03 13:56                                                                         ` Gilles Chanteperdrix
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-04-03 13:46 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Wed, Apr 02, 2014 at 04:41:36PM +0200, Gilles Chanteperdrix wrote:
> It will run the whole LTP testsuite twice, this should last a few
> hours. If one test gets stuck (like mallocstress with some versions
> of gcc), simply kill it, and LTP will continue. I have been running
> a modified version of LTP 2008 since, well, 2008, and have
> reinstalled a more recent version only recently and did not test if
> the changes I made over time to the 2008 version were still needed.

So a run using ltp 2013/09 took about 19 hours.   Some ltp tests failed
(I think they required features I don't have, or too much memory).

Here is the end of the run:

RTH|---------cpu|ctx switches|-------total
RTD|           1|       16599|  1064555712
RTD|     -0.514|      2.327|      4.857|       0|     0|     -1.140|     10.811
RTD|           0|         964|    63476136
'nobody' user id and group found.
'bin' user id and group found.
'daemon' user id and group found.
Users group found.
Sys group found.
RTD|           0|       16616|  1050643816
Required users/groups exist.
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
 
PRETTY_NAME="Debian GNU/Linux 7 (wheezy)"
NAME="Debian GNU/Linux"
VERSION_ID="7"
VERSION="7 (wheezy)"
ID=debian
ANSI_COLOR="1;31"
HOME_URL="http://www.debian.org/"
SUPPORT_URL="http://www.debian.org/support/"
BUG_REPORT_URL="http://bugs.debian.org/"
Linux omap5 3.12-1-dra7xx #1 SMP PREEMPT Debian 3.12.14-0.1 (2014-03-24) armv7l GNU/Linux
RTD|           1|       16760|  1064572472
 
RTD|     -0.840|      2.326|      4.694|       0|     0|     -1.140|     10.811
RTD|           1|        1033|    63435838
Gnu C                  gcc (Debian 4.6.3-14) 4.6.3
RTD|           0|        1033|    63477169
Gnu make               3.81
util-linux             linux 2.20.1
mount                  linux 2.20.1 (with libblkid and selinux support)
RTD|           0|       16377|  1050660193
modutils               9
e2fsprogs              1.42.5
RTD|           1|       16870|  1064589342
RTD|     -0.677|      2.365|      4.368|       0|     0|     -1.140|     10.811
RTD|           1|         970|    63436808
PPP                    2.4.5
RTD|           0|        1035|    63478204
RTD|           0|       16449|  1050676642
Linux C Library        > libc.2.13
Dynamic linker (ldd)   2.13
RTD|           1|       16667|  1064606009
RTD|     -0.678|      2.343|      4.856|       0|     0|     -1.140|     10.811
RTD|           1|        1031|    63437839
Procps                 3.3.3
RTD|           0|         968|    63479172
Net-tools              1.60
iproute2              iproute2-ss120521
Kbd                    1.15.3
RTD|           0|       15909|  1050692551
Sh-utils               8.13
Modules Loaded         xeno_rtipc xeno_switchtest xeno_timerbench xeno_posix xeno_rtdm xeno_native xeno_nucleus ipv6 xhci_hcd dwc3 omap_aes ahci_platform phy_omap_usb2 phy_omap_pipe3 phy_omap_control dwc3_omap omap_des rtc_m41t80

free reports:
             total       used       free     shared    buffers     cached
Mem:       1528608     318704    1209904          0      64520      53200
-/+ buffers/cache:     200984    1327624
Swap:            0          0          0

/proc/cpuinfo
processor       : 0
model name      : ARMv7 Processor rev 2 (v7l)
Features        : swp half thumb fastmult vfp edsp thumbee neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae 
CPU implementer : 0x41
CPU architecture: 7
CPU variant     : 0x2
CPU part        : 0xc0f
CPU revision    : 2

processor       : 1
model name      : ARMv7 Processor rev 2 (v7l)
Features        : swp half thumb fastmult vfp edsp thumbee neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae 
CPU implementer : 0x41
CPU architecture: 7
CPU variant     : 0x2
CPU part        : 0xc0f
CPU revision    : 2

Hardware        : Generic DRA7XX (Flattened Device Tree)
Revision        : 0000
Serial          : 0000000000000000
RTD|           1|       16356|  1064622365
RTD|     -0.678|      2.363|      5.019|       0|     0|     -1.140|     10.811
RTD|           1|         970|    63438809
RTD|           0|         968|    63480140
RTD|           0|       15974|  1050708525
RTD|     -0.678|      2.326|      6.321|       0|     0|     -1.140|     10.811
RTD|           1|       16615|  1064638980
RTD|           1|         966|    63439775
RTT|  18:21:49
RTH|---------cpu|ctx switches|-------total
RTD|           0|        1031|    63481171
RTD|           0|       16665|  1050725190
RTT|  18:21:09  (in-kernel timer handler, 1000 us period, priority 99)
RTH|----lat min|----lat avg|----lat max|-overrun|---msw|---lat best|--lat worst
RTD|     -0.353|      2.369|      4.530|       0|     0|     -1.140|     10.811
RTD|           1|       16856|  1064655836
RTD|           1|        1031|    63440806
RTD|           0|        1035|    63482206
RTD|           0|       16466|  1050741656
RTD|     -0.841|      2.319|      4.693|       0|     0|     -1.140|     10.811
RTD|           1|       16561|  1064672397
RTD|           1|         970|    63441776
RTD|           0|        1035|    63483241
10240+0 records in
10240+0 records out
10240000 bytes (10 MB) copied, 3.46131 s, 3.0 MB/s
RTD|           0|       16603|  1050758259
COMMAND:    /mnt/bin/ltp-pan  -e -S   -a 14348     -n 14348  -p  -f /tmp/ltp-bDTE95Zhcm/alltests -l /mnt/results/LTP_RUN_ON-2014_Apr_03-04h_06m_46s.log  -C /mnt/output/LTP_RUN_ON-2014_Apr_03-04h_06m_46s.failed
LOG File: /mnt/results/LTP_RUN_ON-2014_Apr_03-04h_06m_46s.log
FAILED COMMAND File: /mnt/output/LTP_RUN_ON-2014_Apr_03-04h_06m_46s.failed
Running tests.......
RTD|           1|       16577|  1064688974
RTD|     -0.842|      2.361|      5.669|       0|     0|     -1.140|     10.811
<<<test_start>>>
tag=tcore01 stime=1396512415
cmdline="tcore.sh"
contacts=""
analysis=exit
<<<test_output>>>
RTD|           1|        1031|    63442807
RTD|           0|        1035|    63484276
RTD|           0|       15708|  1050773967
Test Tcore patch 
/mnt/testcases/bin/tcore.sh: 72: cd: can't cd to /lib/i686
RTD|           1|       16410|  1064705384
RTD|     -0.353|      2.310|      5.180|       0|     0|     -1.140|     10.811
RTD|           1|        1035|    63443842
RTD|           0|         970|    63485246
RTD|           0|       16473|  1050790440
RTD|           1|       16492|  1064721876
RTD|     -0.842|      2.342|      5.017|       0|     0|     -1.140|     10.811
RTD|           1|         970|    63444812
RTD|           0|        1031|    63486277
RTT|  18:21:55
RTH|---------cpu|ctx switches|-------total
RTD|           0|       16457|  1050806897
RTD|           1|       16764|  1064738640
RTD|     -0.679|      2.305|      5.180|       0|     0|     -1.140|     10.811
RTD|           1|        1031|    63445843
RTD|           0|       16229|  1050823126
RTD|           0|        1035|    63487312
RTD|           1|       16329|  1064754969
RTD|     -0.680|      2.347|      4.529|       0|     0|     -1.140|     10.811
Test whether we can generate the needed core file
FAIL
/mnt/testcases/bin/tcore.sh: 88: cd: can't cd to /lib/i686
RTD|           1|        1035|    63446878
Test whether the core support bt,fpu and threads commands 
/mnt/testcases/bin/tcore.sh: 128: /mnt/testcases/bin/tcore.sh: expect: not found
RTD|           0|         970|    63488282
RTD|           0|       16151|  1050839277
/mnt/testcases/bin/tcore.sh: 51: exit: Illegal number: -122
RTD|           1|       16538|  1064771507
RTD|     -0.517|      2.300|      5.017|       0|     0|     -1.140|     10.811
RTD|           1|        1035|    63447913
RTD|           0|       16536|  1050855813
RTD|           0|        1031|    63489313
RTD|           1|       16549|  1064788056
RTD|     -0.843|      2.355|      6.156|       0|     0|     -1.140|     10.811
RTD|           1|         968|    63448881
RTD|           0|       16430|  1050872243
RTD|           0|         970|    63490283
RTD|           1|       16785|  1064804841
RTD|     -0.681|      2.297|      4.365|       0|     0|     -1.140|     10.811
RTD|           1|        1033|    63449914
RTD|           0|       16356|  1050888599
RTD|           0|        1031|    63491314
RTD|           1|       16789|  1064821630
RTD|     -0.518|      2.333|      5.504|       0|     0|     -1.140|     10.811
incrementing stop
<<<execution_status>>>
initiation_status="ok"
duration=5 termination_type=exited termination_id=2 corefile=no
cutime=1 cstime=8
<<<test_end>>>
INFO: ltp-pan reported some tests FAIL
LTP Version: 20130904

       ###############################################################

            Done executing testcases.
            LTP Version:  20130904
       ###############################################################

RTD|           0|       16466|  1050905065
RTT|  18:22:01
RTH|---------cpu|ctx switches|-------total
RTD|           1|        1035|    63450949
RTD|           0|         968|    63492282
RTD|     -0.681|      2.284|      5.341|       0|     0|     -1.140|     10.811
RTD|           1|       16531|  1064838161
RTD|           0|       16448|  1050921513
RTD|           1|         970|    63451919
RTD|           0|        1033|    63493315
RTD|           1|       16894|  1064855055
RTD|     -0.518|      2.335|      4.690|       0|     0|     -1.140|     10.811
RTD|           0|       16510|  1050938023
RTD|           1|        1031|    63452950
RTD|           0|        1035|    63494350
RTD|     -0.519|      2.326|      5.178|       0|     0|     -1.140|     10.811
RTD|           1|       16719|  1064871774
RTD|           0|       16004|  1050954027
RTD|           1|        1035|    63453985
RTD|           0|        1035|    63495385
RTD|     -0.519|      2.294|      4.364|       0|     0|     -1.140|     10.811
RTD|           1|       16473|  1064888247
RTD|           0|       16180|  1050970207
RTD|           1|         966|    63454951
RTD|           0|        1035|    63496420
RTT|  18:22:05
RTH|---------cpu|ctx switches|-------total
RTD|           1|       16993|  1064905240
RTD|     -0.845|      2.264|      5.015|       0|     0|     -1.140|     10.811
RTD|           0|       16282|  1050986489
RTD|           1|         970|    63455921
RTD|     -0.682|      2.312|      5.177|       0|     0|     -1.140|     10.811
RTD|           1|       16733|  1064921973
RTD|           0|        1035|    63497455
RTD|           0|       16265|  1051002754
RTD|           1|         966|    63456887
Killed
Load script terminated, terminating checked scripts
---|-----------|-----------|-----------|--------|------|-------------------------
RTS|     -1.140|      2.280|     10.811|       0|     0|    18:21:26/18:21:26
RTD|           0|         795|    63498250
RTD|           0|        4654|  1051007408
RTD|           1|       14862|  1064936835
RTD|           1|         134|    63457021
pipe_in: /tmp/xeno-test-in-9751

I am guessing that looks successful.

fork13 -i 1000000 takes a VERY long time.  I think that test is worth
adjusting a bit.

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-03 13:46                                                                       ` Lennart Sorensen
@ 2014-04-03 13:56                                                                         ` Gilles Chanteperdrix
  2014-04-03 14:16                                                                           ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-04-03 13:56 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 04/03/2014 03:46 PM, Lennart Sorensen wrote:
> Load script terminated, terminating checked scripts
> ---|-----------|-----------|-----------|--------|------|-------------------------
> RTS|     -1.140|      2.280|     10.811|       0|     0|    18:21:26/18:21:26
> RTD|           0|         795|    63498250
> RTD|           0|        4654|  1051007408
> RTD|           1|       14862|  1064936835
> RTD|           1|         134|    63457021
> pipe_in: /tmp/xeno-test-in-9751
>
> I am guessing that looks successful.

Yes, I guess a 15us worst case interrupt latency is unprecedented for 
the ARM architecture. The timer anticipation may be a bit too eager for 
this SOC, which results in negative latencies. What does cat 
/proc/xenomai/timer say?

-- 
					    Gilles.


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-03 13:56                                                                         ` Gilles Chanteperdrix
@ 2014-04-03 14:16                                                                           ` Lennart Sorensen
  2014-04-14 21:06                                                                             ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-04-03 14:16 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Thu, Apr 03, 2014 at 03:56:26PM +0200, Gilles Chanteperdrix wrote:
> On 04/03/2014 03:46 PM, Lennart Sorensen wrote:
> >Load script terminated, terminating checked scripts
> >---|-----------|-----------|-----------|--------|------|-------------------------
> >RTS|     -1.140|      2.280|     10.811|       0|     0|    18:21:26/18:21:26
> >RTD|           0|         795|    63498250
> >RTD|           0|        4654|  1051007408
> >RTD|           1|       14862|  1064936835
> >RTD|           1|         134|    63457021
> >pipe_in: /tmp/xeno-test-in-9751
> >
> >I am guessing that looks successful.
> 
> Yes, I guess a 15us worst case interrupt latency is unprecedented
> for the ARM architecture. The timer anticipation may be a bit too
> eager for this SOC, which results in negative latencies. What does
> cat /proc/xenomai/timer say?

root@omap5:~# cat /proc/xenomai/timer
status=on+watchdog:setup=488:clock=3556147959244:timerdev=arch_sys_timer:clockdev=ipipe_tsc

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-03 14:16                                                                           ` Lennart Sorensen
@ 2014-04-14 21:06                                                                             ` Lennart Sorensen
  2014-04-15 11:39                                                                               ` Gilles Chanteperdrix
  0 siblings, 1 reply; 45+ messages in thread
From: Lennart Sorensen @ 2014-04-14 21:06 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Thu, Apr 03, 2014 at 10:16:35AM -0400, Lennart Sorensen wrote:
> On Thu, Apr 03, 2014 at 03:56:26PM +0200, Gilles Chanteperdrix wrote:
> > On 04/03/2014 03:46 PM, Lennart Sorensen wrote:
> > >Load script terminated, terminating checked scripts
> > >---|-----------|-----------|-----------|--------|------|-------------------------
> > >RTS|     -1.140|      2.280|     10.811|       0|     0|    18:21:26/18:21:26
> > >RTD|           0|         795|    63498250
> > >RTD|           0|        4654|  1051007408
> > >RTD|           1|       14862|  1064936835
> > >RTD|           1|         134|    63457021
> > >pipe_in: /tmp/xeno-test-in-9751
> > >
> > >I am guessing that looks successful.
> > 
> > Yes, I guess a 15us worst case interrupt latency is unprecedented
> > for the ARM architecture. The timer anticipation may be a bit too
> > eager for this SOC, which results in negative latencies. What does
> > cat /proc/xenomai/timer say?
> 
> root@omap5:~# cat /proc/xenomai/timer
> status=on+watchdog:setup=488:clock=3556147959244:timerdev=arch_sys_timer:clockdev=ipipe_tsc

Any more info on this?

The negative minimum latency seems a bit odd after all.

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-14 21:06                                                                             ` Lennart Sorensen
@ 2014-04-15 11:39                                                                               ` Gilles Chanteperdrix
  2014-06-13 18:15                                                                                 ` Lennart Sorensen
  0 siblings, 1 reply; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-04-15 11:39 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 04/14/2014 11:06 PM, Lennart Sorensen wrote:
> On Thu, Apr 03, 2014 at 10:16:35AM -0400, Lennart Sorensen wrote:
>> On Thu, Apr 03, 2014 at 03:56:26PM +0200, Gilles Chanteperdrix wrote:
>>> On 04/03/2014 03:46 PM, Lennart Sorensen wrote:
>>>> Load script terminated, terminating checked scripts
>>>> ---|-----------|-----------|-----------|--------|------|-------------------------
>>>> RTS|     -1.140|      2.280|     10.811|       0|     0|    18:21:26/18:21:26
>>>> RTD|           0|         795|    63498250
>>>> RTD|           0|        4654|  1051007408
>>>> RTD|           1|       14862|  1064936835
>>>> RTD|           1|         134|    63457021
>>>> pipe_in: /tmp/xeno-test-in-9751
>>>>
>>>> I am guessing that looks successful.
>>>
>>> Yes, I guess a 15us worst case interrupt latency is unprecedented
>>> for the ARM architecture. The timer anticipation may be a bit too
>>> eager for this SOC, which results in negative latencies. What does
>>> cat /proc/xenomai/timer say?
>>
>> root@omap5:~# cat /proc/xenomai/timer
>> status=on+watchdog:setup=488:clock=3556147959244:timerdev=arch_sys_timer:clockdev=ipipe_tsc
> 
> Any more info on this?
> 
> The negative minimum latency seems a bit odd after all.
> 
No, it is a bit strange, since the anticipation is 488ns, the negative
latency should be less than twice that. Unfortunately, I can not
reproduce this issue easily. What you could try is to change the way the
timer setup time is calculated, and use the average value, instead of
average + std deviation.

-- 
                                                                Gilles.


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-04-15 11:39                                                                               ` Gilles Chanteperdrix
@ 2014-06-13 18:15                                                                                 ` Lennart Sorensen
  0 siblings, 0 replies; 45+ messages in thread
From: Lennart Sorensen @ 2014-06-13 18:15 UTC (permalink / raw)
  To: Gilles Chanteperdrix; +Cc: xenomai

On Tue, Apr 15, 2014 at 01:39:32PM +0200, Gilles Chanteperdrix wrote:
> On 04/14/2014 11:06 PM, Lennart Sorensen wrote:
> > On Thu, Apr 03, 2014 at 10:16:35AM -0400, Lennart Sorensen wrote:
> >> On Thu, Apr 03, 2014 at 03:56:26PM +0200, Gilles Chanteperdrix wrote:
> >>> On 04/03/2014 03:46 PM, Lennart Sorensen wrote:
> >>>> Load script terminated, terminating checked scripts
> >>>> ---|-----------|-----------|-----------|--------|------|-------------------------
> >>>> RTS|     -1.140|      2.280|     10.811|       0|     0|    18:21:26/18:21:26
> >>>> RTD|           0|         795|    63498250
> >>>> RTD|           0|        4654|  1051007408
> >>>> RTD|           1|       14862|  1064936835
> >>>> RTD|           1|         134|    63457021
> >>>> pipe_in: /tmp/xeno-test-in-9751
> >>>>
> >>>> I am guessing that looks successful.
> >>>
> >>> Yes, I guess a 15us worst case interrupt latency is unprecedented
> >>> for the ARM architecture. The timer anticipation may be a bit too
> >>> eager for this SOC, which results in negative latencies. What does
> >>> cat /proc/xenomai/timer say?
> >>
> >> root@omap5:~# cat /proc/xenomai/timer
> >> status=on+watchdog:setup=488:clock=3556147959244:timerdev=arch_sys_timer:clockdev=ipipe_tsc
> > 
> > Any more info on this?
> > 
> > The negative minimum latency seems a bit odd after all.
> > 
> No, it is a bit strange, since the anticipation is 488ns, the negative
> latency should be less than twice that. Unfortunately, I can not
> reproduce this issue easily. What you could try is to change the way the
> timer setup time is calculated, and use the average value, instead of
> average + std deviation.

Well I still haven't maanged to figure this out.

I do have a question though.  Any idea what this means:

[4976920.784397] Brought up 2 CPUs
[4976920.784413] SMP: Total of 2 processors activated.
[4976920.784421] CPU: All CPU(s) started in SVC mode.
[4976920.784888] 
[4976920.784897] =================================
[4976920.784903] [ INFO: inconsistent lock state ]
[4976920.784911] 3.12-1-dra7xx #1 Not tainted
[4976920.784918] ---------------------------------
[4976920.784925] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
[4976920.784934] swapper/0/0 [HC0[0]:SC0[0]:HE1:SE1] takes:
[4976920.784941]  (std_spinlock_raw(&rq->lock)){?.....}, at: [<c042d100>] __schedule+0x554/0x80c
[4976920.784975] {IN-HARDIRQ-W} state was registered at:
[4976920.784982]   [<c009ab8c>] __lock_acquire+0xac4/0x1bb0
[4976920.784999]   [<c009c1e8>] lock_acquire+0x94/0x13c
[4976920.785012]   [<c042e700>] _raw_spin_lock+0x38/0x48
[4976920.785025]   [<c006e7a8>] scheduler_tick+0x2c/0xb4
[4976920.785038]   [<c004dfa8>] update_process_times+0x5c/0x68
[4976920.785051]   [<c00938b4>] tick_periodic+0x38/0xb4
[4976920.785063]   [<c0093a40>] tick_handle_periodic+0x18/0x7c
[4976920.785075]   [<c034b4ec>] arch_timer_handler_virt+0x64/0x80
[4976920.785088]   [<c0087c70>] handle_percpu_devid_irq+0x84/0x1e0
[4976920.785100]   [<c0084c6c>] generic_handle_irq+0x20/0x30
[4976920.785113]   [<c000f57c>] handle_IRQ+0x5c/0xd0
[4976920.785127]   [<c00c2890>] __ipipe_do_sync_stage+0x2e4/0x300
[4976920.785140]   [<c0008678>] __ipipe_grab_irq+0x48/0x8c
[4976920.785151]   [<c0008988>] gic_handle_irq+0x28/0x5c
[4976920.785161]   [<c042f504>] __irq_svc+0x44/0x70
[4976920.785174]   [<c00c2aa0>] ipipe_unstall_root+0x44/0x5c
[4976920.785186]   [<c063c9a0>] start_kernel+0x1fc/0x2dc
[4976920.785200]   [<80008074>] 0x80008074
[4976920.785212] irq event stamp: 29364
[4976920.785218] hardirqs last  enabled at (29363): [<c042eec4>] _raw_spin_unlock_irq+0x24/0x50
[4976920.785233] hardirqs last disabled at (29364): [<c042e7c8>] _raw_spin_lock_irqsave+0x1c/0x60
[4976920.785246] softirqs last  enabled at (29354): [<c0045ea4>] irq_enter+0x6c/0x70
[4976920.785258] softirqs last disabled at (29353): [<c0045e98>] irq_enter+0x60/0x70
[4976920.785270] 
[4976920.785270] other info that might help us debug this:
[4976920.785277]  Possible unsafe locking scenario:
[4976920.785277] 
[4976920.785285]        CPU0
[4976920.785290]        ----
[4976920.785296]   lock(std_spinlock_raw(&rq->lock));
[4976920.785309]   <Interrupt>
[4976920.785315]     lock(std_spinlock_raw(&rq->lock));
[4976920.785328] 
[4976920.785328]  *** DEADLOCK ***
[4976920.785328] 
[4976920.785338] 1 lock held by swapper/0/0:
[4976920.785344]  #0:  (std_spinlock_raw(&rq->lock)){?.....}, at: [<c042d100>] __schedule+0x554/0x80c
[4976920.785372] 
[4976920.785372] stack backtrace:
[4976920.785384] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.12-1-dra7xx #1 Debian 3.12.22-0.1RR2
[4976920.785403] [<c001612c>] (unwind_backtrace+0x0/0xf8) from [<c00126d8>] (show_stack+0x10/0x14)
[4976920.785417] [<c00126d8>] (show_stack+0x10/0x14) from [<c0429240>] (dump_stack+0x6c/0xac)
[4976920.785430] [<c0429240>] (dump_stack+0x6c/0xac) from [<c0426740>] (print_usage_bug+0x258/0x2c8)
[4976920.785443] [<c0426740>] (print_usage_bug+0x258/0x2c8) from [<c0099c90>] (mark_lock+0x290/0x6c8)
[4976920.785457] [<c0099c90>] (mark_lock+0x290/0x6c8) from [<c009ca54>] (mark_held_locks+0x60/0x138)
[4976920.785471] [<c009ca54>] (mark_held_locks+0x60/0x138) from [<c009cb9c>] (trace_hardirqs_on_caller+0x70/0x1c4)
[4976920.785485] [<c009cb9c>] (trace_hardirqs_on_caller+0x70/0x1c4) from [<c042f534>] (__ipipe_fast_svc_irq_exit+0x4/0x14)
[4976920.785503] [<c042f534>] (__ipipe_fast_svc_irq_exit+0x4/0x14) from [<c0019bbc>] (ipipe_test_and_stall_root+0x4/0x48)
[4976920.785517] [<c0019bbc>] (ipipe_test_and_stall_root+0x4/0x48) from [<c009bf60>] (lock_release+0x30/0x224)
[4976920.785531] [<c009bf60>] (lock_release+0x30/0x224) from [<c042ee58>] (_raw_spin_unlock_irqrestore+0x1c/0x64)
[4976920.785545] [<c042ee58>] (_raw_spin_unlock_irqrestore+0x1c/0x64) from [<c042d12c>] (__schedule+0x580/0x80c)
[4976920.785558] [<c042d12c>] (__schedule+0x580/0x80c) from [<c042d88c>] (schedule_preempt_disabled+0x14/0x20)
[4976920.785572] [<c042d88c>] (schedule_preempt_disabled+0x14/0x20) from [<c00849fc>] (cpu_startup_entry+0x1ec/0x23c)
[4976920.785586] [<c00849fc>] (cpu_startup_entry+0x1ec/0x23c) from [<c063ca3c>] (start_kernel+0x298/0x2dc)
[4976920.785597] [<c063ca3c>] (start_kernel+0x298/0x2dc) from [<80008074>] (0x80008074)
[4976920.905231] devtmpfs: initialized

We see that every boot.  Things seem to work fine afterwards, but it
sure looks wrong.

-- 
Len Sorensen


^ permalink raw reply	[flat|nested] 45+ messages in thread

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
  2014-03-31 18:24   ` Lennart Sorensen
  2014-03-31 19:15     ` Lennart Sorensen
@ 2014-03-31 19:19     ` Gilles Chanteperdrix
  1 sibling, 0 replies; 45+ messages in thread
From: Gilles Chanteperdrix @ 2014-03-31 19:19 UTC (permalink / raw)
  To: Lennart Sorensen; +Cc: xenomai

On 03/31/2014 08:24 PM, Lennart Sorensen wrote:
> On Mon, Mar 31, 2014 at 08:12:37PM +0200, Gilles Chanteperdrix wrote:
>> On what platform do you get this? If on cortex A8, and the
>> user-space is compiled in thumb2 mode, note that an erratum
>> workaround is needed, flushing the BTB at each context switch to
>> avoid problem when ARM code is replaced by THUMB code at the same
>> (virtual) address when switching context.
> 
> Cortex-A15 (Omap5 system).  User space is thumb2 (Debian Wheezy armhf
> based).

I have an omap5 here, but did not finish the port. In particular, omap5
seems to hang after a while if unlocked context switch is enabled.
> 
>> My advice would be to wait, Philippe is currently merging the I-pipe
>> git with 3.14 (you can actually find the 3.12 merge in my git tree,
>> under the branch raw/for-ipipe-3.12.0, it has been lightly tested
>> though, as I wait for 3.14 to be ready to test more thoroughly).
> 
> Unfortunately the drivers are not fully merged upstream yet, so I am
> using the 3.12 branch from ti's git tree.  I was able to boot 3.14 but
> without ethernet and usb and a few other things.
> 
> Comparing the ipipe changes for 3.14 would be useful though.
> 
> I only saw 3.11 raw in the tree when I was doing that part on thursday.
> Is this new?  Or did I look in the wrong git tree?  No, I did a pull,
> and it is there now.  I guess I was a day or two early. :)

I think Philippe started the port last week, and I fixed the two arm
conflicts during the week-end, so yes, this is fairly recent.

-- 
                                                                Gilles.


^ permalink raw reply	[flat|nested] 45+ messages in thread

[parent not found: <mailman.33.1396388743.2839.xenomai@xenomai.org>]

* Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
       [not found] <mailman.33.1396388743.2839.xenomai@xenomai.org>
@ 2014-04-02  9:21 ` Andreas Glatz
  0 siblings, 0 replies; 45+ messages in thread
From: Andreas Glatz @ 2014-04-02  9:21 UTC (permalink / raw)
  To: xenomai

> Message: 7
> Date: Tue, 1 Apr 2014 17:45:39 -0400
> From: "Lennart Sorensen" <lsorense@csclub.uwaterloo.ca>
> To: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
> Cc: xenomai@xenomai.org
> Subject: Re: [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel
> Message-ID: <20140401214539.GD17765@csclub.uwaterloo.ca>
> Content-Type: text/plain; charset=us-ascii
>
> On Tue, Apr 01, 2014 at 10:52:31PM +0200, Gilles Chanteperdrix wrote:
>> On 04/01/2014 09:40 PM, Lennart Sorensen wrote:
>>> On Tue, Apr 01, 2014 at 09:35:24PM +0200, Gilles Chanteperdrix  
>>> wrote:
>>>> On 04/01/2014 03:12 PM, Lennart Sorensen wrote:
>>>>> On Tue, Apr 01, 2014 at 12:52:44PM +0200, Gilles Chanteperdrix  
>>>>> wrote:
>>>>>> The way I test it is by running xeno-regression-test, using  
>>>>>> dohell with
>>>>>> LTP to create a load. Note that the latency result given by
>>>>>> xeno-regression-test should not be taken into account as  
>>>>>> switchtest is
>>>>>> running concurrently and creates large non-preemptible sections,
>>>>>> xeno-regression-test is more a stress test.
>>>>>
>>>>> I will see if I can find the invocation to run that then.
>>>>>
>>>>> I let cyclictest, switchtest and latency running the last 8 hours,
>>>>> and latency test currently says:
>>>>>
>>>>> RTD|     -0.814|      2.441|      7.486|       0|     0|      
>>>>> -2.116|     20.182
>>>>>
>>>>> That seems decent at least.
>>>>>
>>>>
>>>> I use:
>>>> xeno-regression-test -l "dohell -s 192.168.0.5 -m /mnt -l /ltp"
>>>>
>>>> Where the machine with ip 192.168.0.5 has the "discard" service  
>>>> enabled
>>>> (port 9, available in inetd), an usb key is mounted on /mnt, and  
>>>> LTP is
>>>> installed in /ltp.
>>>
>>> I get an error when I use the -s option.
>>
>> Probably because the machine with the IP address you pass after -s  
>> does
>> not have the "discard" service enabled in inetd.conf
>
>

[...]

> d14: 1 != 2
> d15: 1 != 2
> == FPU check routines: OK.
> /usr/bin/xeno-regression-test failed: child 14296 exited with status 2
>
> I was running:
>
> xeno-regression-test xeno-regression-test -l "dohell -s 10.200.19.25  
> -m /mnt -l /mnt" -t 2
>
> Maybe I got something wrong.
>
> ltp is installed to /mnt (which is a USB stick).
>

On my board the directory where 'dohell' resides was not included in  
PATH. Maybe try this:

  xeno-regression-test -l "/usr/lib/xenomai/testsuite/dohell -s  
10.200.19.25 -m /mnt -l /mnt" -t 2

A.




^ permalink raw reply	[flat|nested] 45+ messages in thread

end of thread, other threads:[~2014-06-13 18:15 UTC | newest]

Thread overview: 45+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-03-31 17:45 [Xenomai] Porting xenomai 2.6.3 and ipipe to 3.12 kernel Lennart Sorensen
2014-03-31 18:12 ` Gilles Chanteperdrix
2014-03-31 18:24   ` Lennart Sorensen
2014-03-31 19:15     ` Lennart Sorensen
2014-03-31 19:17       ` Gilles Chanteperdrix
2014-03-31 19:18         ` Lennart Sorensen
2014-03-31 19:37           ` Lennart Sorensen
2014-03-31 19:44             ` Gilles Chanteperdrix
2014-03-31 20:42               ` Lennart Sorensen
2014-03-31 20:53                 ` Lennart Sorensen
2014-03-31 20:57                   ` Lennart Sorensen
2014-03-31 21:06                     ` Gilles Chanteperdrix
2014-03-31 21:25                       ` Lennart Sorensen
2014-03-31 21:49                         ` Gilles Chanteperdrix
2014-03-31 21:53                           ` Lennart Sorensen
2014-03-31 21:59                             ` Lennart Sorensen
2014-03-31 22:04                               ` Lennart Sorensen
2014-03-31 22:11                                 ` Gilles Chanteperdrix
2014-03-31 22:27                                   ` Gilles Chanteperdrix
2014-04-01  1:32                                     ` Lennart Sorensen
2014-04-01 10:52                                       ` Gilles Chanteperdrix
2014-04-01 13:12                                         ` Lennart Sorensen
2014-04-01 19:35                                           ` Gilles Chanteperdrix
2014-04-01 19:40                                             ` Lennart Sorensen
2014-04-01 20:52                                               ` Gilles Chanteperdrix
2014-04-01 21:45                                                 ` Lennart Sorensen
2014-04-01 22:01                                                   ` Gilles Chanteperdrix
2014-04-02  2:35                                                   ` Lennart Sorensen
2014-04-02  7:11                                                     ` Gilles Chanteperdrix
2014-04-02 13:24                                                       ` Lennart Sorensen
2014-04-02 13:26                                                         ` Gilles Chanteperdrix
2014-04-02 13:40                                                           ` Lennart Sorensen
2014-04-02 13:41                                                             ` Lennart Sorensen
2014-04-02 13:46                                                               ` Lennart Sorensen
2014-04-02 13:56                                                                 ` Gilles Chanteperdrix
2014-04-02 14:38                                                                   ` Lennart Sorensen
2014-04-02 14:41                                                                     ` Gilles Chanteperdrix
2014-04-03 13:46                                                                       ` Lennart Sorensen
2014-04-03 13:56                                                                         ` Gilles Chanteperdrix
2014-04-03 14:16                                                                           ` Lennart Sorensen
2014-04-14 21:06                                                                             ` Lennart Sorensen
2014-04-15 11:39                                                                               ` Gilles Chanteperdrix
2014-06-13 18:15                                                                                 ` Lennart Sorensen
2014-03-31 19:19     ` Gilles Chanteperdrix
     [not found] <mailman.33.1396388743.2839.xenomai@xenomai.org>
2014-04-02  9:21 ` Andreas Glatz

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.