* [PATCH 0/2] Add more peripherals to the sam9rlek @ 2014-04-15 11:07 ` Alexandre Belloni 0 siblings, 0 replies; 8+ messages in thread From: Alexandre Belloni @ 2014-04-15 11:07 UTC (permalink / raw) To: linux-arm-kernel Hi, this patch set adds support for SPI, LCD, i2c, ADC and touchscreen, USB gadget and PWM on the at91sam9rlek. The only missing piece is now audio/ac97 support, then the SoC will be entirely supported using DT. Alexandre Belloni (2): ARM: at91/dt: sam9rl: add lcd, adc, usb gadget and pwm support ARM: at91/dt: add peripherals to the at91sam9rlek board arch/arm/boot/dts/at91sam9rl.dtsi | 265 +++++++++++++++++++++++++++++++++++-- arch/arm/boot/dts/at91sam9rlek.dts | 90 ++++++++++++- 2 files changed, 342 insertions(+), 13 deletions(-) -- 1.8.3.2 ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH 0/2] Add more peripherals to the sam9rlek @ 2014-04-15 11:07 ` Alexandre Belloni 0 siblings, 0 replies; 8+ messages in thread From: Alexandre Belloni @ 2014-04-15 11:07 UTC (permalink / raw) To: Nicolas Ferre Cc: Jean-Christophe Plagniol-Villard, linux-arm-kernel, linux-kernel, Alexandre Belloni Hi, this patch set adds support for SPI, LCD, i2c, ADC and touchscreen, USB gadget and PWM on the at91sam9rlek. The only missing piece is now audio/ac97 support, then the SoC will be entirely supported using DT. Alexandre Belloni (2): ARM: at91/dt: sam9rl: add lcd, adc, usb gadget and pwm support ARM: at91/dt: add peripherals to the at91sam9rlek board arch/arm/boot/dts/at91sam9rl.dtsi | 265 +++++++++++++++++++++++++++++++++++-- arch/arm/boot/dts/at91sam9rlek.dts | 90 ++++++++++++- 2 files changed, 342 insertions(+), 13 deletions(-) -- 1.8.3.2 ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH 1/2] ARM: at91/dt: sam9rl: add lcd, adc, usb gadget and pwm support 2014-04-15 11:07 ` Alexandre Belloni @ 2014-04-15 11:07 ` Alexandre Belloni -1 siblings, 0 replies; 8+ messages in thread From: Alexandre Belloni @ 2014-04-15 11:07 UTC (permalink / raw) To: linux-arm-kernel This patch adds support for the ADC, LCD, USB gadget and PWM controllers to the at91sam9rl. It also reorders the pinctrl_spi0 as it was not correctly sorted. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> --- arch/arm/boot/dts/at91sam9rl.dtsi | 265 ++++++++++++++++++++++++++++++++++++-- 1 file changed, 256 insertions(+), 9 deletions(-) diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi index 63e1784d272c..6202e161314a 100644 --- a/arch/arm/boot/dts/at91sam9rl.dtsi +++ b/arch/arm/boot/dts/at91sam9rl.dtsi @@ -11,6 +11,7 @@ #include <dt-bindings/clk/at91.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pwm/pwm.h> / { model = "Atmel AT91SAM9RL family SoC"; @@ -32,6 +33,7 @@ i2c1 = &i2c1; ssc0 = &ssc0; ssc1 = &ssc1; + pwm0 = &pwm0; }; cpus { @@ -48,12 +50,31 @@ reg = <0x20000000 0x04000000>; }; + clocks { + adc_op_clk: adc_op_clk{ + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <1000000>; + }; + }; + ahb { compatible = "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges; + fb0: fb at 00500000 { + compatible = "atmel,at91sam9rl-lcdc"; + reg = <0x00500000 0x1000>; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fb>; + clocks = <&lcd_clk>, <&lcd_clk>; + clock-names = "hclk", "lcdc_clk"; + status = "disabled"; + }; + nand0: nand at 40000000 { compatible = "atmel,at91rm9200-nand"; #address-cells = <1>; @@ -187,6 +208,16 @@ status = "disabled"; }; + pwm0: pwm at fffc8000 { + compatible = "atmel,at91sam9rl-pwm"; + reg = <0xfffc8000 0x300>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH 4>; + #pwm-cells = <3>; + clocks = <&pwm_clk>; + clock-names = "pwm_clk"; + status = "disabled"; + }; + spi0: spi at fffcc000 { #address-cells = <1>; #size-cells = <0>; @@ -200,6 +231,111 @@ status = "disabled"; }; + adc0: adc at fffd0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91sam9rl-adc"; + reg = <0xfffd0000 0x100>; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&adc_clk>, <&adc_op_clk>; + clock-names = "adc_clk", "adc_op_clk"; + atmel,adc-use-external-triggers; + atmel,adc-channels-used = <0x3f>; + atmel,adc-vref = <3300>; + atmel,adc-startup-time = <40>; + atmel,adc-res = <8 10>; + atmel,adc-res-names = "lowres", "highres"; + atmel,adc-use-res = "highres"; + + trigger at 0 { + reg = <0>; + trigger-name = "timer-counter-0"; + trigger-value = <0x1>; + }; + trigger at 1 { + reg = <1>; + trigger-name = "timer-counter-1"; + trigger-value = <0x3>; + }; + + trigger at 2 { + reg = <2>; + trigger-name = "timer-counter-2"; + trigger-value = <0x5>; + }; + + trigger at 3 { + reg = <3>; + trigger-name = "external"; + trigger-value = <0x13>; + trigger-external; + }; + }; + + usb0: gadget at fffd4000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91sam9rl-udc"; + reg = <0x00600000 0x100000>, + <0xfffd4000 0x4000>; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>; + clocks = <&udphs_clk>, <&utmi>; + clock-names = "pclk", "hclk"; + status = "disabled"; + + ep0 { + reg = <0>; + atmel,fifo-size = <64>; + atmel,nb-banks = <1>; + }; + + ep1 { + reg = <1>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <2>; + atmel,can-dma; + atmel,can-isoc; + }; + + ep2 { + reg = <2>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <2>; + atmel,can-dma; + atmel,can-isoc; + }; + + ep3 { + reg = <3>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <3>; + atmel,can-dma; + }; + + ep4 { + reg = <4>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <3>; + atmel,can-dma; + }; + + ep5 { + reg = <5>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <3>; + atmel,can-dma; + atmel,can-isoc; + }; + + ep6 { + reg = <6>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <3>; + atmel,can-dma; + atmel,can-isoc; + }; + }; + ramc0: ramc at ffffea00 { compatible = "atmel,at91sam9260-sdramc"; reg = <0xffffea00 0x200>; @@ -238,6 +374,44 @@ <0x003fffff 0x0001ff3c>; /* pioD */ /* shared pinctrl settings */ + adc0 { + pinctrl_adc0_ts: adc0_ts-0 { + atmel,pins = + <AT91_PIOA 17 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOA 18 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOA 19 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_adc0_ad0: adc0_ad0-0 { + atmel,pins = <AT91_PIOA 17 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_adc0_ad1: adc0_ad1-0 { + atmel,pins = <AT91_PIOA 18 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_adc0_ad2: adc0_ad2-0 { + atmel,pins = <AT91_PIOA 19 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_adc0_ad3: adc0_ad3-0 { + atmel,pins = <AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_adc0_ad4: adc0_ad4-0 { + atmel,pins = <AT91_PIOD 6 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_adc0_ad5: adc0_ad5-0 { + atmel,pins = <AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_adc0_adtrg: adc0_adtrg-0 { + atmel,pins = <AT91_PIOB 15 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + }; + dbgu { pinctrl_dbgu: dbgu-0 { atmel,pins = @@ -246,6 +420,33 @@ }; }; + fb { + pinctrl_fb: fb-0 { + atmel,pins = + <AT91_PIOC 1 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 3 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOC 5 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOC 6 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOC 7 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOC 9 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 10 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 11 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 12 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 13 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 15 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 16 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 17 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 18 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 19 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 20 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 21 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 22 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 23 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 24 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 25 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + }; + i2c_gpio0 { pinctrl_i2c_gpio0: i2c_gpio0-0 { atmel,pins = @@ -307,6 +508,61 @@ }; }; + pwm0 { + pinctrl_pwm0_pwm0_0: pwm0_pwm0-0 { + atmel,pins = <AT91_PIOB 8 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm0_1: pwm0_pwm0-1 { + atmel,pins = <AT91_PIOC 2 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm0_2: pwm0_pwm0-2 { + atmel,pins = <AT91_PIOD 14 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm1_0: pwm0_pwm1-0 { + atmel,pins = <AT91_PIOB 9 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm1_1: pwm0_pwm1-1 { + atmel,pins = <AT91_PIOC 3 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm1_2: pwm0_pwm1-2 { + atmel,pins = <AT91_PIOD 15 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm2_0: pwm0_pwm2-0 { + atmel,pins = <AT91_PIOD 5 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm2_1: pwm0_pwm2-1 { + atmel,pins = <AT91_PIOD 12 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm2_2: pwm0_pwm2-2 { + atmel,pins = <AT91_PIOD 16 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm3_0: pwm0_pwm3-0 { + atmel,pins = <AT91_PIOD 8 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm3_1: pwm0_pwm3-1 { + atmel,pins = <AT91_PIOD 18 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + }; + + spi0 { + pinctrl_spi0: spi0-0 { + atmel,pins = + <AT91_PIOA 25 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + }; + ssc0 { pinctrl_ssc0_tx: ssc0_tx-0 { atmel,pins = @@ -339,15 +595,6 @@ }; }; - spi0 { - pinctrl_spi0: spi0-0 { - atmel,pins = - <AT91_PIOA 25 AT91_PERIPH_A AT91_PINCTRL_NONE>, - <AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_NONE>, - <AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_NONE>; - }; - }; - tcb0 { pinctrl_tcb0_tclk0: tcb0_tclk0-0 { atmel,pins = <AT91_PIOA 3 AT91_PERIPH_B AT91_PINCTRL_NONE>; -- 1.8.3.2 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 1/2] ARM: at91/dt: sam9rl: add lcd, adc, usb gadget and pwm support @ 2014-04-15 11:07 ` Alexandre Belloni 0 siblings, 0 replies; 8+ messages in thread From: Alexandre Belloni @ 2014-04-15 11:07 UTC (permalink / raw) To: Nicolas Ferre Cc: Jean-Christophe Plagniol-Villard, linux-arm-kernel, linux-kernel, Alexandre Belloni This patch adds support for the ADC, LCD, USB gadget and PWM controllers to the at91sam9rl. It also reorders the pinctrl_spi0 as it was not correctly sorted. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> --- arch/arm/boot/dts/at91sam9rl.dtsi | 265 ++++++++++++++++++++++++++++++++++++-- 1 file changed, 256 insertions(+), 9 deletions(-) diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi index 63e1784d272c..6202e161314a 100644 --- a/arch/arm/boot/dts/at91sam9rl.dtsi +++ b/arch/arm/boot/dts/at91sam9rl.dtsi @@ -11,6 +11,7 @@ #include <dt-bindings/clk/at91.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pwm/pwm.h> / { model = "Atmel AT91SAM9RL family SoC"; @@ -32,6 +33,7 @@ i2c1 = &i2c1; ssc0 = &ssc0; ssc1 = &ssc1; + pwm0 = &pwm0; }; cpus { @@ -48,12 +50,31 @@ reg = <0x20000000 0x04000000>; }; + clocks { + adc_op_clk: adc_op_clk{ + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <1000000>; + }; + }; + ahb { compatible = "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges; + fb0: fb@00500000 { + compatible = "atmel,at91sam9rl-lcdc"; + reg = <0x00500000 0x1000>; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH 3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fb>; + clocks = <&lcd_clk>, <&lcd_clk>; + clock-names = "hclk", "lcdc_clk"; + status = "disabled"; + }; + nand0: nand@40000000 { compatible = "atmel,at91rm9200-nand"; #address-cells = <1>; @@ -187,6 +208,16 @@ status = "disabled"; }; + pwm0: pwm@fffc8000 { + compatible = "atmel,at91sam9rl-pwm"; + reg = <0xfffc8000 0x300>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH 4>; + #pwm-cells = <3>; + clocks = <&pwm_clk>; + clock-names = "pwm_clk"; + status = "disabled"; + }; + spi0: spi@fffcc000 { #address-cells = <1>; #size-cells = <0>; @@ -200,6 +231,111 @@ status = "disabled"; }; + adc0: adc@fffd0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91sam9rl-adc"; + reg = <0xfffd0000 0x100>; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&adc_clk>, <&adc_op_clk>; + clock-names = "adc_clk", "adc_op_clk"; + atmel,adc-use-external-triggers; + atmel,adc-channels-used = <0x3f>; + atmel,adc-vref = <3300>; + atmel,adc-startup-time = <40>; + atmel,adc-res = <8 10>; + atmel,adc-res-names = "lowres", "highres"; + atmel,adc-use-res = "highres"; + + trigger@0 { + reg = <0>; + trigger-name = "timer-counter-0"; + trigger-value = <0x1>; + }; + trigger@1 { + reg = <1>; + trigger-name = "timer-counter-1"; + trigger-value = <0x3>; + }; + + trigger@2 { + reg = <2>; + trigger-name = "timer-counter-2"; + trigger-value = <0x5>; + }; + + trigger@3 { + reg = <3>; + trigger-name = "external"; + trigger-value = <0x13>; + trigger-external; + }; + }; + + usb0: gadget@fffd4000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91sam9rl-udc"; + reg = <0x00600000 0x100000>, + <0xfffd4000 0x4000>; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>; + clocks = <&udphs_clk>, <&utmi>; + clock-names = "pclk", "hclk"; + status = "disabled"; + + ep0 { + reg = <0>; + atmel,fifo-size = <64>; + atmel,nb-banks = <1>; + }; + + ep1 { + reg = <1>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <2>; + atmel,can-dma; + atmel,can-isoc; + }; + + ep2 { + reg = <2>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <2>; + atmel,can-dma; + atmel,can-isoc; + }; + + ep3 { + reg = <3>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <3>; + atmel,can-dma; + }; + + ep4 { + reg = <4>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <3>; + atmel,can-dma; + }; + + ep5 { + reg = <5>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <3>; + atmel,can-dma; + atmel,can-isoc; + }; + + ep6 { + reg = <6>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <3>; + atmel,can-dma; + atmel,can-isoc; + }; + }; + ramc0: ramc@ffffea00 { compatible = "atmel,at91sam9260-sdramc"; reg = <0xffffea00 0x200>; @@ -238,6 +374,44 @@ <0x003fffff 0x0001ff3c>; /* pioD */ /* shared pinctrl settings */ + adc0 { + pinctrl_adc0_ts: adc0_ts-0 { + atmel,pins = + <AT91_PIOA 17 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOA 18 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOA 19 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_adc0_ad0: adc0_ad0-0 { + atmel,pins = <AT91_PIOA 17 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_adc0_ad1: adc0_ad1-0 { + atmel,pins = <AT91_PIOA 18 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_adc0_ad2: adc0_ad2-0 { + atmel,pins = <AT91_PIOA 19 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_adc0_ad3: adc0_ad3-0 { + atmel,pins = <AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_adc0_ad4: adc0_ad4-0 { + atmel,pins = <AT91_PIOD 6 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_adc0_ad5: adc0_ad5-0 { + atmel,pins = <AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_adc0_adtrg: adc0_adtrg-0 { + atmel,pins = <AT91_PIOB 15 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + }; + dbgu { pinctrl_dbgu: dbgu-0 { atmel,pins = @@ -246,6 +420,33 @@ }; }; + fb { + pinctrl_fb: fb-0 { + atmel,pins = + <AT91_PIOC 1 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 3 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOC 5 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOC 6 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOC 7 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOC 9 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 10 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 11 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 12 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 13 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 15 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 16 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 17 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 18 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 19 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 20 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 21 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 22 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 23 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 24 AT91_PERIPH_B AT91_PINCTRL_NONE>, + <AT91_PIOC 25 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + }; + i2c_gpio0 { pinctrl_i2c_gpio0: i2c_gpio0-0 { atmel,pins = @@ -307,6 +508,61 @@ }; }; + pwm0 { + pinctrl_pwm0_pwm0_0: pwm0_pwm0-0 { + atmel,pins = <AT91_PIOB 8 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm0_1: pwm0_pwm0-1 { + atmel,pins = <AT91_PIOC 2 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm0_2: pwm0_pwm0-2 { + atmel,pins = <AT91_PIOD 14 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm1_0: pwm0_pwm1-0 { + atmel,pins = <AT91_PIOB 9 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm1_1: pwm0_pwm1-1 { + atmel,pins = <AT91_PIOC 3 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm1_2: pwm0_pwm1-2 { + atmel,pins = <AT91_PIOD 15 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm2_0: pwm0_pwm2-0 { + atmel,pins = <AT91_PIOD 5 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm2_1: pwm0_pwm2-1 { + atmel,pins = <AT91_PIOD 12 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm2_2: pwm0_pwm2-2 { + atmel,pins = <AT91_PIOD 16 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm3_0: pwm0_pwm3-0 { + atmel,pins = <AT91_PIOD 8 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; + + pinctrl_pwm0_pwm3_1: pwm0_pwm3-1 { + atmel,pins = <AT91_PIOD 18 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + }; + + spi0 { + pinctrl_spi0: spi0-0 { + atmel,pins = + <AT91_PIOA 25 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_NONE>, + <AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_NONE>; + }; + }; + ssc0 { pinctrl_ssc0_tx: ssc0_tx-0 { atmel,pins = @@ -339,15 +595,6 @@ }; }; - spi0 { - pinctrl_spi0: spi0-0 { - atmel,pins = - <AT91_PIOA 25 AT91_PERIPH_A AT91_PINCTRL_NONE>, - <AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_NONE>, - <AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_NONE>; - }; - }; - tcb0 { pinctrl_tcb0_tclk0: tcb0_tclk0-0 { atmel,pins = <AT91_PIOA 3 AT91_PERIPH_B AT91_PINCTRL_NONE>; -- 1.8.3.2 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 2/2] ARM: at91/dt: add peripherals to the at91sam9rlek board 2014-04-15 11:07 ` Alexandre Belloni @ 2014-04-15 11:07 ` Alexandre Belloni -1 siblings, 0 replies; 8+ messages in thread From: Alexandre Belloni @ 2014-04-15 11:07 UTC (permalink / raw) To: linux-arm-kernel This adds support for: - SPI - Dataflash - LCD - i2c - ADC - Touchscreen - USB gadget - PWM Also it switches the ds1 and ds2 leds to PWM control. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> --- arch/arm/boot/dts/at91sam9rlek.dts | 90 ++++++++++++++++++++++++++++++++++++-- 1 file changed, 86 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/at91sam9rlek.dts b/arch/arm/boot/dts/at91sam9rlek.dts index cddb37825fad..f148fa4b3ab9 100644 --- a/arch/arm/boot/dts/at91sam9rlek.dts +++ b/arch/arm/boot/dts/at91sam9rlek.dts @@ -32,6 +32,37 @@ }; ahb { + fb0: fb at 00500000 { + display = <&display0>; + status = "okay"; + + display0: display { + bits-per-pixel = <16>; + atmel,lcdcon-backlight; + atmel,dmacon = <0x1>; + atmel,lcdcon2 = <0x80008002>; + atmel,guard-time = <1>; + atmel,lcd-wiring-mode = "RGB"; + + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <4965000>; + hactive = <240>; + vactive = <320>; + hback-porch = <1>; + hfront-porch = <33>; + vback-porch = <1>; + vfront-porch = <0>; + hsync-len = <5>; + vsync-len = <1>; + hsync-active = <1>; + vsync-active = <1>; + }; + }; + }; + }; + nand0: nand at 40000000 { nand-bus-width = <8>; nand-ecc-mode = "soft"; @@ -92,6 +123,43 @@ status = "okay"; }; + adc0: adc at fffd0000 { + pinctrl-names = "default"; + pinctrl-0 = < + &pinctrl_adc0_ad0 + &pinctrl_adc0_ad1 + &pinctrl_adc0_ad2 + &pinctrl_adc0_ad3 + &pinctrl_adc0_ad4 + &pinctrl_adc0_ad5 + &pinctrl_adc0_adtrg>; + atmel,adc-ts-wires = <4>; + status = "okay"; + }; + + usb0: gadget at fffd4000 { + atmel,vbus-gpio = <&pioA 8 GPIO_ACTIVE_HIGH>; + status = "okay"; + }; + + spi0: spi at fffcc000 { + status = "okay"; + cs-gpios = <&pioA 28 0>, <0>, <0>, <0>; + mtd_dataflash at 0 { + compatible = "atmel,at45", "atmel,dataflash"; + spi-max-frequency = <15000000>; + reg = <0>; + }; + }; + + pwm0: pwm at fffc8000 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_pwm1_2>, + <&pinctrl_pwm0_pwm2_2>; + }; + dbgu: serial at fffff200 { status = "okay"; }; @@ -117,18 +185,24 @@ }; }; - leds { - compatible = "gpio-leds"; + pwmleds { + compatible = "pwm-leds"; ds1 { label = "ds1"; - gpios = <&pioD 15 GPIO_ACTIVE_LOW>; + pwms = <&pwm0 1 5000 PWM_POLARITY_INVERTED>; + max-brightness = <255>; }; ds2 { label = "ds2"; - gpios = <&pioD 16 GPIO_ACTIVE_LOW>; + pwms = <&pwm0 2 5000 PWM_POLARITY_INVERTED>; + max-brightness = <255>; }; + }; + + leds { + compatible = "gpio-leds"; ds3 { label = "ds3"; @@ -154,4 +228,12 @@ gpio-key,wakeup; }; }; + + i2c at 0 { + status = "okay"; + }; + + i2c at 1 { + status = "okay"; + }; }; -- 1.8.3.2 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 2/2] ARM: at91/dt: add peripherals to the at91sam9rlek board @ 2014-04-15 11:07 ` Alexandre Belloni 0 siblings, 0 replies; 8+ messages in thread From: Alexandre Belloni @ 2014-04-15 11:07 UTC (permalink / raw) To: Nicolas Ferre Cc: Jean-Christophe Plagniol-Villard, linux-arm-kernel, linux-kernel, Alexandre Belloni This adds support for: - SPI - Dataflash - LCD - i2c - ADC - Touchscreen - USB gadget - PWM Also it switches the ds1 and ds2 leds to PWM control. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> --- arch/arm/boot/dts/at91sam9rlek.dts | 90 ++++++++++++++++++++++++++++++++++++-- 1 file changed, 86 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/at91sam9rlek.dts b/arch/arm/boot/dts/at91sam9rlek.dts index cddb37825fad..f148fa4b3ab9 100644 --- a/arch/arm/boot/dts/at91sam9rlek.dts +++ b/arch/arm/boot/dts/at91sam9rlek.dts @@ -32,6 +32,37 @@ }; ahb { + fb0: fb@00500000 { + display = <&display0>; + status = "okay"; + + display0: display { + bits-per-pixel = <16>; + atmel,lcdcon-backlight; + atmel,dmacon = <0x1>; + atmel,lcdcon2 = <0x80008002>; + atmel,guard-time = <1>; + atmel,lcd-wiring-mode = "RGB"; + + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <4965000>; + hactive = <240>; + vactive = <320>; + hback-porch = <1>; + hfront-porch = <33>; + vback-porch = <1>; + vfront-porch = <0>; + hsync-len = <5>; + vsync-len = <1>; + hsync-active = <1>; + vsync-active = <1>; + }; + }; + }; + }; + nand0: nand@40000000 { nand-bus-width = <8>; nand-ecc-mode = "soft"; @@ -92,6 +123,43 @@ status = "okay"; }; + adc0: adc@fffd0000 { + pinctrl-names = "default"; + pinctrl-0 = < + &pinctrl_adc0_ad0 + &pinctrl_adc0_ad1 + &pinctrl_adc0_ad2 + &pinctrl_adc0_ad3 + &pinctrl_adc0_ad4 + &pinctrl_adc0_ad5 + &pinctrl_adc0_adtrg>; + atmel,adc-ts-wires = <4>; + status = "okay"; + }; + + usb0: gadget@fffd4000 { + atmel,vbus-gpio = <&pioA 8 GPIO_ACTIVE_HIGH>; + status = "okay"; + }; + + spi0: spi@fffcc000 { + status = "okay"; + cs-gpios = <&pioA 28 0>, <0>, <0>, <0>; + mtd_dataflash@0 { + compatible = "atmel,at45", "atmel,dataflash"; + spi-max-frequency = <15000000>; + reg = <0>; + }; + }; + + pwm0: pwm@fffc8000 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_pwm1_2>, + <&pinctrl_pwm0_pwm2_2>; + }; + dbgu: serial@fffff200 { status = "okay"; }; @@ -117,18 +185,24 @@ }; }; - leds { - compatible = "gpio-leds"; + pwmleds { + compatible = "pwm-leds"; ds1 { label = "ds1"; - gpios = <&pioD 15 GPIO_ACTIVE_LOW>; + pwms = <&pwm0 1 5000 PWM_POLARITY_INVERTED>; + max-brightness = <255>; }; ds2 { label = "ds2"; - gpios = <&pioD 16 GPIO_ACTIVE_LOW>; + pwms = <&pwm0 2 5000 PWM_POLARITY_INVERTED>; + max-brightness = <255>; }; + }; + + leds { + compatible = "gpio-leds"; ds3 { label = "ds3"; @@ -154,4 +228,12 @@ gpio-key,wakeup; }; }; + + i2c@0 { + status = "okay"; + }; + + i2c@1 { + status = "okay"; + }; }; -- 1.8.3.2 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 0/2] Add more peripherals to the sam9rlek 2014-04-15 11:07 ` Alexandre Belloni @ 2014-04-18 14:15 ` Nicolas Ferre -1 siblings, 0 replies; 8+ messages in thread From: Nicolas Ferre @ 2014-04-18 14:15 UTC (permalink / raw) To: linux-arm-kernel On 15/04/2014 13:07, Alexandre Belloni : > Hi, this patch set adds support for SPI, LCD, i2c, ADC and touchscreen, USB > gadget and PWM on the at91sam9rlek. > > The only missing piece is now audio/ac97 support, then the SoC will be entirely > supported using DT. > > Alexandre Belloni (2): > ARM: at91/dt: sam9rl: add lcd, adc, usb gadget and pwm support > ARM: at91/dt: add peripherals to the at91sam9rlek board Ok: both added to at91-3.16-dt Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> > > arch/arm/boot/dts/at91sam9rl.dtsi | 265 +++++++++++++++++++++++++++++++++++-- > arch/arm/boot/dts/at91sam9rlek.dts | 90 ++++++++++++- > 2 files changed, 342 insertions(+), 13 deletions(-) > -- Nicolas Ferre ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 0/2] Add more peripherals to the sam9rlek @ 2014-04-18 14:15 ` Nicolas Ferre 0 siblings, 0 replies; 8+ messages in thread From: Nicolas Ferre @ 2014-04-18 14:15 UTC (permalink / raw) To: Alexandre Belloni Cc: Jean-Christophe Plagniol-Villard, linux-arm-kernel, linux-kernel On 15/04/2014 13:07, Alexandre Belloni : > Hi, this patch set adds support for SPI, LCD, i2c, ADC and touchscreen, USB > gadget and PWM on the at91sam9rlek. > > The only missing piece is now audio/ac97 support, then the SoC will be entirely > supported using DT. > > Alexandre Belloni (2): > ARM: at91/dt: sam9rl: add lcd, adc, usb gadget and pwm support > ARM: at91/dt: add peripherals to the at91sam9rlek board Ok: both added to at91-3.16-dt Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> > > arch/arm/boot/dts/at91sam9rl.dtsi | 265 +++++++++++++++++++++++++++++++++++-- > arch/arm/boot/dts/at91sam9rlek.dts | 90 ++++++++++++- > 2 files changed, 342 insertions(+), 13 deletions(-) > -- Nicolas Ferre ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2014-04-18 14:15 UTC | newest] Thread overview: 8+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2014-04-15 11:07 [PATCH 0/2] Add more peripherals to the sam9rlek Alexandre Belloni 2014-04-15 11:07 ` Alexandre Belloni 2014-04-15 11:07 ` [PATCH 1/2] ARM: at91/dt: sam9rl: add lcd, adc, usb gadget and pwm support Alexandre Belloni 2014-04-15 11:07 ` Alexandre Belloni 2014-04-15 11:07 ` [PATCH 2/2] ARM: at91/dt: add peripherals to the at91sam9rlek board Alexandre Belloni 2014-04-15 11:07 ` Alexandre Belloni 2014-04-18 14:15 ` [PATCH 0/2] Add more peripherals to the sam9rlek Nicolas Ferre 2014-04-18 14:15 ` Nicolas Ferre
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.