Re: [PATCH 09/11] brcmfmac: Fix OOB interrupt not working for BCM43362

[Arend van Spriel <arend@broadcom.com>]

On 05/26/14 09:48, Hans de Goede wrote:
> It has taken me a long long time to get the OOB interrupt working on the
> AP6210 sdio wifi/bt module found on various Allwinner A20 boards. In the
> end I found these magic register pokes in the cubietruck kernel tree:
> https://github.com/cubieboard2/linux-sunxi/commit/7f08ba395617d17e7a711507503d89a50406fe7a
>
> I'm not entirely sure if this specific to the AP6210 module, or if this
> should be done for all BCM43362 sdio devices.

Let keep it as this for now. I added some remarks below.

Regards,
Arend

> Signed-off-by: Hans de Goede<hdegoede@redhat.com>
> ---
>   drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c | 18 ++++++++++++++++++
>   1 file changed, 18 insertions(+)
>
> diff --git a/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c b/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
> index 0fc707c..2369a0f 100644
> --- a/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
> +++ b/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
> @@ -39,7 +39,9 @@
>   #include<brcm_hw_ids.h>
>   #include<brcmu_utils.h>
>   #include<brcmu_wifi.h>
> +#include<chipcommon.h>
>   #include<soc.h>
> +#include "chip.h"
>   #include "dhd_bus.h"
>   #include "dhd_dbg.h"
>   #include "sdio_host.h"
> @@ -119,6 +121,7 @@ int brcmf_sdiod_intr_register(struct brcmf_sdio_dev *sdiodev)
>   {
>   	int ret = 0;
>   	u8 data;
> +	u32 addr, gpiocontrol;
>   	unsigned long flags;
>
>   	if ((sdiodev->pdata)&&  (sdiodev->pdata->oob_irq_supported)) {
> @@ -148,6 +151,21 @@ int brcmf_sdiod_intr_register(struct brcmf_sdio_dev *sdiodev)
>
>   		sdio_claim_host(sdiodev->func[1]);
>
> +		if (sdiodev->bus_if->chip == BCM43362_CHIP_ID) {
+			/* assign GPIO to SDIO core */
> +			addr = CORE_CC_REG(SI_ENUM_BASE, gpiocontrol);
> +			gpiocontrol = brcmf_sdiod_regrl(sdiodev, addr,&ret);
> +			gpiocontrol |= 0x2;
> +			brcmf_sdiod_regwl(sdiodev, addr, gpiocontrol,&ret);
> +
> +			/* SPROM_ADDR_HIGH ? perhaps the defines name is off */

These names are all off. These should be:
SBSDIO_SPROM_ADDR_HIGH = SBSDIO_GPIO_SELECT
SBSDIO_CHIP_CTRL_DATA = SBSDIO_GPIO_OUT
SBSDIO_CHIP_CTRL_EN = SBSDIO_GPIO_EN

> +			brcmf_sdiod_regwb(sdiodev, SBSDIO_SPROM_ADDR_HIGH, 0xf,
> +					&ret);
> +			brcmf_sdiod_regwb(sdiodev, SBSDIO_CHIP_CTRL_DATA, 0,
> +					&ret);
> +			brcmf_sdiod_regwb(sdiodev, SBSDIO_CHIP_CTRL_EN, 0x2,
> +					&ret);
> +		}
> +
>   		/* must configure SDIO_CCCR_IENx to enable irq */
>   		data = brcmf_sdiod_regrb(sdiodev, SDIO_CCCR_IENx,&ret);
>   		data |= 1<<  SDIO_FUNC_1 | 1<<  SDIO_FUNC_2 | 1;