From: "Jörg Krause" <jkrause@posteo.de>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH] usb: ci_udc: fix interaction with CONFIG_USB_ETH_CDC
Date: Sat, 28 Jun 2014 22:37:35 +0200 [thread overview]
Message-ID: <53AF278F.80403@posteo.de> (raw)
In-Reply-To: <53AE1BA9.9000401@posteo.de>
On 06/28/2014 09:59 PM, Marek Vasut wrote:
> I would actually be really glad if you could test plain u-boot-usb/master and
> see if your USB problem is present there. Also, it would be really nice to
> isolate the sequence of commands which triggers the bug, so we have a proper
> reproducible testcase.
>
> Anyway, this thread is not a place where I would like to discuss this. This
> should be discussed in the "original" thread, that is:
>
> Subj: [PATCH] usb: ci_udc: fix interaction with CONFIG_USB_ETH_CDC
I cloned u-boot-usb/master and tested it. I am running "tftpd
rootfs.ubifs" several times. Here is the log (I shortened the loading
process bar):
HTLLCLLC
U-Boot 2014.07-rc3-g18e0313 (Jun 28 2014 - 22:17:52)
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: NAND, 3V3
DRAM: 64 MiB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: usb_ether [PRIME]
Hit any key to stop autoboot: 0
=> tftp rootfs.ubifs
using ci_udc, OUT ep- IN ep- STATUS ep-
MAC 00:19:b8:00:00:02
HOST MAC 00:19:b8:00:00:01
high speed config #1: 2 mA, Ethernet Gadget, using CDC Ethernet
USB network up!
Using usb_ether device
TFTP from server 10.0.0.1; our IP address is 10.0.0.2
Filename 'rootfs.ubifs'.
Load address: 0x40008000
Loading: [snip]
##############################################################T ###
[snip]
1.7 MiB/s
done
Bytes transferred = 13205504 (c98000 hex)
=> tftp rootfs.ubifs
using ci_udc, OUT ep- IN ep- STATUS ep-
MAC 00:19:b8:00:00:02
HOST MAC 00:19:b8:00:00:01
high speed config #1: 2 mA, Ethernet Gadget, using CDC Ethernet
USB network up!
Using usb_ether device
TFTP from server 10.0.0.1; our IP address is 10.0.0.2
Filename 'rootfs.ubifs'.
Load address: 0x40008000
Loading:
#################################################################
[snip]
5.6 MiB/s
done
Bytes transferred = 13205504 (c98000 hex)
=> tftp rootfs.ubifs
using ci_udc, OUT ep- IN ep- STATUS ep-
MAC 00:19:b8:00:00:02
HOST MAC 00:19:b8:00:00:01
high speed config #1: 2 mA, Ethernet Gadget, using CDC Ethernet
USB network up!
Using usb_ether device
TFTP from server 10.0.0.1; our IP address is 10.0.0.2
Filename 'rootfs.ubifs'.
Load address: 0x40008000
Loading:
#################################################################
[snip]
5.6 MiB/s
done
Bytes transferred = 13205504 (c98000 hex)
=> tftp rootfs.ubifs
using ci_udc, OUT ep- IN ep- STATUS ep-
MAC 00:19:b8:00:00:02
HOST MAC 00:19:b8:00:00:01
high speed config #1: 2 mA, Ethernet Gadget, using CDC Ethernet
ERROR: The remote end did not respond in time.
at drivers/usb/gadget/ether.c:2388/usb_eth_init()
=>
The error always appears after calling tftp the third time! The first
two runs work fine, but the third one always fails. I run this test
about 20 times.
Best regards
J?rg Krause
next prev parent reply other threads:[~2014-06-28 20:37 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-06-23 18:02 [U-Boot] [PATCH] usb: ci_udc: fix interaction with CONFIG_USB_ETH_CDC Stephen Warren
2014-06-23 19:03 ` Eric Nelson
2014-06-25 13:51 ` Marek Vasut
2014-06-25 16:06 ` Stephen Warren
2014-06-27 21:37 ` Jörg Krause
2014-06-27 21:52 ` Jörg Krause
2014-06-27 21:56 ` Stephen Warren
2014-06-27 23:27 ` Jörg Krause
2014-06-27 21:55 ` Stephen Warren
2014-06-27 23:16 ` Jörg Krause
2014-06-27 23:37 ` Stephen Warren
2014-06-28 0:09 ` Jörg Krause
2014-06-28 1:34 ` Jörg Krause
2014-06-28 20:37 ` Jörg Krause [this message]
2014-06-28 20:45 ` Marek Vasut
2014-06-28 20:53 ` Jörg Krause
2014-06-29 20:33 ` Jörg Krause
2014-06-30 9:37 ` Marek Vasut
2014-06-30 13:34 ` Jörg Krause
2014-06-30 16:02 ` Stephen Warren
2014-06-30 19:55 ` Stephen Warren
2014-06-30 22:44 ` Jörg Krause
2014-06-30 22:51 ` Stephen Warren
2014-06-30 23:17 ` Jörg Krause
2014-06-30 23:56 ` Marek Vasut
2014-06-30 20:55 ` Jörg Krause
2014-06-30 21:15 ` Marek Vasut
2014-06-30 21:43 ` Jörg Krause
2014-06-30 21:50 ` Marek Vasut
2014-06-25 20:20 ` Marek Vasut
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=53AF278F.80403@posteo.de \
--to=jkrause@posteo.de \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.