Re: [PATCH v4 05/11] Documentation: dt: add ti,am3353_wkup_m3 bindings

[Suman Anna <s-anna@ti.com>]

Hi Dave,

On 07/14/2014 09:41 AM, Santosh Shilimkar wrote:
> On Thursday 10 July 2014 10:55 PM, Dave Gerlach wrote:
>> Add the device tree bindings document for am3353 wkup_m3.
>>
>> Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
>> CC: Ohad Ben-Cohen <ohad@wizery.com>
>> CC: Benoit Cousson <bcousson@baylibre.com>
>> ---
> Looks like you missed to copy device tree list and maintainers.
> As Tony suggested, split up the series and send the wkup_m3 related
> patches separately along with bindings and mark the DT folks on email.
> 
>>  .../bindings/remoteproc/wkup_m3_rproc.txt          | 46 ++++++++++++++++++++++
>>  1 file changed, 46 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt
>>
>> diff --git a/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt b/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt
>> new file mode 100644
>> index 0000000..e9dd909
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/remoteproc/wkup_m3_rproc.txt
>> @@ -0,0 +1,46 @@
>> +Wakeup M3 Remote Proc Driver
>> +=====================
>> +
>> +TI AMx3 Family devices use a Cortex M3 co-processor to help with various
>> +low power tasks that cannot be controlled from the MPU. The CM3 requires
>> +a firmware binary to accomplish this and communicates with the MPU through
>> +IPC registers present in the SoCs control module. The wkup_m3 remoteproc
>> +driver handles the loading of the firmware and exposes an API to
>> +communicate with the wkup_m3 through the use of the IPC registers and a
>> +mailbox.
>> +
>> +Wkup M3 Device Node:
>> +====================
>> +A wkup_m3 device node is used to represent a wakeup M3 IP instance within
>> +a SoC. The sub-mailboxes are represented as child node of this parent node.
>> +
>> +Required properties:
>> +--------------------
>> +- compatible:		Should be "ti,am3353-wkup-m3" for AM33xx SoCs
>> +- reg:			Contains the wkup_m3 register address ranges for
>> +			umem, dmem, and ipc-regs.
>> +- reg-names:		Names for reg addresses given above

You should explicitly state the names here. Giving any different names
will cause the driver to fail.

>> +- interrupts:		Contains the interrupt information for the wkup_m3
>> +			interrupt that signals the MPU.
>> +- ti,hwmods:		Name of the hwmod associated with the mailbox

hwmod is not associated with mailbox here, please fix the cut-copy-paste
error.

regards
Suman


>> +- ti,no-reset-on-init:	Reset is handled after fw has been loaded, not at
>> +			init of hwmod.
>> +- mbox-names:		Name of the mbox channel for the IPC framework
>> +- mbox:			Phandle used by IPC framework to get correct mbox
>> +			channel for communication.
>> +
>> +Example:
>> +--------
>> +/* AM33xx */
>> +wkup_m3: wkup_m3@44d00000 {
>> +	compatible = "ti,am3353-wkup-m3";
>> +	reg = <0x44d00000 0x4000
>> +	       0x44d80000 0x2000
>> +	       0x44e11324 0x0024>;
>> +	reg-names = "m3_umem", "m3_dmem", "ipc_regs";
>> +	interrupts = <78>;
>> +	ti,hwmods = "wkup_m3";
>> +	ti,no-reset-on-init;
>> +	mbox-names = "wkup_m3";
>> +	mbox = <&mailbox &mbox_wkupm3>;
>> +};
>>
>