[PATCH v3 1/2] ARM: at91/dt: describe rgmii ethernet phy connected to sama5d3xek boards

[nicolas.ferre@atmel.com (Nicolas Ferre)]

On 10/07/2014 21:59, Boris BREZILLON :
> Add ethernet-phy nodes and specify phy interrupt (connected to pin PB25)
> and board specific timing configs.
> 
> Atmel has two different HW designs for its CPU modules: the first one
> (produced by Embest) is connecting PHYAD[0-2] pins to pull up resistors
> and the other one (produced by Ronetix) is connecting PHYAD0 to a pull up
> resistor and PHYAD[1-2] to pull down resistors.
> As a result, Ronetix design will have its PHY available at address 0x1 and
> Embest design at 0x7.
> By defining both phys we're letting the phy core detect the one actually
> available on the MDIO bus.
> 
> Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
> ---
> 
> Florian, I dropped your Reviewed-by tag because this patch has slightly
> changed.

Hi Florian,

I would like to have your Ack on this one as we discussed this solution
with you.

Thanks, bye,


>  arch/arm/boot/dts/sama5d3xcm.dtsi | 30 ++++++++++++++++++++++++++++++
>  1 file changed, 30 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sama5d3xcm.dtsi b/arch/arm/boot/dts/sama5d3xcm.dtsi
> index b0b1331..755369e 100644
> --- a/arch/arm/boot/dts/sama5d3xcm.dtsi
> +++ b/arch/arm/boot/dts/sama5d3xcm.dtsi
> @@ -34,6 +34,36 @@
>  
>  			macb0: ethernet at f0028000 {
>  				phy-mode = "rgmii";
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				ethernet-phy at 1 {
> +					reg = <0x1>;
> +					interrupt-parent = <&pioB>;
> +					interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> +					txen-skew-ps = <800>;
> +					txc-skew-ps = <3000>;
> +					rxdv-skew-ps = <400>;
> +					rxc-skew-ps = <3000>;
> +					rxd0-skew-ps = <400>;
> +					rxd1-skew-ps = <400>;
> +					rxd2-skew-ps = <400>;
> +					rxd3-skew-ps = <400>;
> +				};
> +
> +				ethernet-phy at 7 {
> +					reg = <0x7>;
> +					interrupt-parent = <&pioB>;
> +					interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> +					txen-skew-ps = <800>;
> +					txc-skew-ps = <3000>;
> +					rxdv-skew-ps = <400>;
> +					rxc-skew-ps = <3000>;
> +					rxd0-skew-ps = <400>;
> +					rxd1-skew-ps = <400>;
> +					rxd2-skew-ps = <400>;
> +					rxd3-skew-ps = <400>;
> +				};
>  			};
>  
>  			pmc: pmc at fffffc00 {
> 


-- 
Nicolas Ferre