All of lore.kernel.org
 help / color / mirror / Atom feed
From: Mikko Perttunen <mperttunen-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
To: Thierry Reding <thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Cc: "swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org"
	<swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org>,
	"linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org"
	<linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>,
	"linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org"
	<linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org>,
	"linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org"
	<linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>
Subject: Re: [PATCH 2/3] ARM: tegra: Add PMC thermtrip programming to Jetson TK1 device tree
Date: Wed, 13 Aug 2014 11:06:14 +0300	[thread overview]
Message-ID: <53EB1C76.2000702@nvidia.com> (raw)
In-Reply-To: <20140813080324.GC7735@ulmo>



On 13/08/14 11:03, Thierry Reding wrote:
> * PGP Signed by an unknown key
>
> On Wed, Aug 13, 2014 at 10:52:18AM +0300, Mikko Perttunen wrote:
>> On 13/08/14 10:37, Thierry Reding wrote:
>>>> Old Signed by an unknown key
>>>
>>> On Tue, Aug 05, 2014 at 11:12:59AM +0300, Mikko Perttunen wrote:
>>>> This adds the required information to reset the board during an overheating
>>>> situation to the Jetson TK1 device tree. The thermal reset is handled by the
>>>> PMC by sending an I2C message to the PMIC. The entries specify the I2C
>>>> message to be sent.
>>>>
>>>> Signed-off-by: Mikko Perttunen <mperttunen-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
>>>> ---
>>>>   arch/arm/boot/dts/tegra124-jetson-tk1.dts | 5 +++++
>>>>   1 file changed, 5 insertions(+)
>>>>
>>>> diff --git a/arch/arm/boot/dts/tegra124-jetson-tk1.dts b/arch/arm/boot/dts/tegra124-jetson-tk1.dts
>>>> index 624b0fb..ee178c4 100644
>>>> --- a/arch/arm/boot/dts/tegra124-jetson-tk1.dts
>>>> +++ b/arch/arm/boot/dts/tegra124-jetson-tk1.dts
>>>> @@ -1617,6 +1617,11 @@
>>>>   		nvidia,core-pwr-off-time = <61036>;
>>>>   		nvidia,core-power-req-active-high;
>>>>   		nvidia,sys-clock-req-active-high;
>>>> +
>>>> +		nvidia,thermtrip-pmu-i2c-addr = <0x40>;
>>>> +		nvidia,thermtrip-i2c-controller = <4>;
>>>> +		nvidia,thermtrip-reg-addr = <0x36>;
>>>> +		nvidia,thermtrip-reg-data = <0x2>;
>>>
>>> Given the number of properties that this can potentially have, I wonder
>>> if perhaps it would be a good idea to put this into a subnode, like
>>> this:
>>>
>>> 		thermtrip {
>>> 			pmu-i2c-addr = <0x40>;
>>> 			i2c-controller = <4>;
>>> 			...
>>> 		};
>>
>> I guess that'd look a bit nicer.
>
> Mind you, this may be somewhat on the edge of what's considered good
> practice for DT content, so maybe wait for a second opinion before going
> ahead with this.
>
> I don't have any objections to a set of nvidia,thermtrip-* properties, I
> just think it's fairly redundant to keep repeating that prefix (and it
> causes ugliness in drivers, too).

Hmm, ok. I'll fix the other stuff first.

>
> Thierry
>
> * Unknown Key
> * 0x7F3EB3A1
>

WARNING: multiple messages have this Message-ID (diff)
From: mperttunen@nvidia.com (Mikko Perttunen)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 2/3] ARM: tegra: Add PMC thermtrip programming to Jetson TK1 device tree
Date: Wed, 13 Aug 2014 11:06:14 +0300	[thread overview]
Message-ID: <53EB1C76.2000702@nvidia.com> (raw)
In-Reply-To: <20140813080324.GC7735@ulmo>



On 13/08/14 11:03, Thierry Reding wrote:
> * PGP Signed by an unknown key
>
> On Wed, Aug 13, 2014 at 10:52:18AM +0300, Mikko Perttunen wrote:
>> On 13/08/14 10:37, Thierry Reding wrote:
>>>> Old Signed by an unknown key
>>>
>>> On Tue, Aug 05, 2014 at 11:12:59AM +0300, Mikko Perttunen wrote:
>>>> This adds the required information to reset the board during an overheating
>>>> situation to the Jetson TK1 device tree. The thermal reset is handled by the
>>>> PMC by sending an I2C message to the PMIC. The entries specify the I2C
>>>> message to be sent.
>>>>
>>>> Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
>>>> ---
>>>>   arch/arm/boot/dts/tegra124-jetson-tk1.dts | 5 +++++
>>>>   1 file changed, 5 insertions(+)
>>>>
>>>> diff --git a/arch/arm/boot/dts/tegra124-jetson-tk1.dts b/arch/arm/boot/dts/tegra124-jetson-tk1.dts
>>>> index 624b0fb..ee178c4 100644
>>>> --- a/arch/arm/boot/dts/tegra124-jetson-tk1.dts
>>>> +++ b/arch/arm/boot/dts/tegra124-jetson-tk1.dts
>>>> @@ -1617,6 +1617,11 @@
>>>>   		nvidia,core-pwr-off-time = <61036>;
>>>>   		nvidia,core-power-req-active-high;
>>>>   		nvidia,sys-clock-req-active-high;
>>>> +
>>>> +		nvidia,thermtrip-pmu-i2c-addr = <0x40>;
>>>> +		nvidia,thermtrip-i2c-controller = <4>;
>>>> +		nvidia,thermtrip-reg-addr = <0x36>;
>>>> +		nvidia,thermtrip-reg-data = <0x2>;
>>>
>>> Given the number of properties that this can potentially have, I wonder
>>> if perhaps it would be a good idea to put this into a subnode, like
>>> this:
>>>
>>> 		thermtrip {
>>> 			pmu-i2c-addr = <0x40>;
>>> 			i2c-controller = <4>;
>>> 			...
>>> 		};
>>
>> I guess that'd look a bit nicer.
>
> Mind you, this may be somewhat on the edge of what's considered good
> practice for DT content, so maybe wait for a second opinion before going
> ahead with this.
>
> I don't have any objections to a set of nvidia,thermtrip-* properties, I
> just think it's fairly redundant to keep repeating that prefix (and it
> causes ugliness in drivers, too).

Hmm, ok. I'll fix the other stuff first.

>
> Thierry
>
> * Unknown Key
> * 0x7F3EB3A1
>

WARNING: multiple messages have this Message-ID (diff)
From: Mikko Perttunen <mperttunen@nvidia.com>
To: Thierry Reding <thierry.reding@gmail.com>
Cc: "swarren@wwwdotorg.org" <swarren@wwwdotorg.org>,
	"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
	"linux-arm-kernel@lists.infradead.org" 
	<linux-arm-kernel@lists.infradead.org>,
	"linux-tegra@vger.kernel.org" <linux-tegra@vger.kernel.org>
Subject: Re: [PATCH 2/3] ARM: tegra: Add PMC thermtrip programming to Jetson TK1 device tree
Date: Wed, 13 Aug 2014 11:06:14 +0300	[thread overview]
Message-ID: <53EB1C76.2000702@nvidia.com> (raw)
In-Reply-To: <20140813080324.GC7735@ulmo>



On 13/08/14 11:03, Thierry Reding wrote:
> * PGP Signed by an unknown key
>
> On Wed, Aug 13, 2014 at 10:52:18AM +0300, Mikko Perttunen wrote:
>> On 13/08/14 10:37, Thierry Reding wrote:
>>>> Old Signed by an unknown key
>>>
>>> On Tue, Aug 05, 2014 at 11:12:59AM +0300, Mikko Perttunen wrote:
>>>> This adds the required information to reset the board during an overheating
>>>> situation to the Jetson TK1 device tree. The thermal reset is handled by the
>>>> PMC by sending an I2C message to the PMIC. The entries specify the I2C
>>>> message to be sent.
>>>>
>>>> Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
>>>> ---
>>>>   arch/arm/boot/dts/tegra124-jetson-tk1.dts | 5 +++++
>>>>   1 file changed, 5 insertions(+)
>>>>
>>>> diff --git a/arch/arm/boot/dts/tegra124-jetson-tk1.dts b/arch/arm/boot/dts/tegra124-jetson-tk1.dts
>>>> index 624b0fb..ee178c4 100644
>>>> --- a/arch/arm/boot/dts/tegra124-jetson-tk1.dts
>>>> +++ b/arch/arm/boot/dts/tegra124-jetson-tk1.dts
>>>> @@ -1617,6 +1617,11 @@
>>>>   		nvidia,core-pwr-off-time = <61036>;
>>>>   		nvidia,core-power-req-active-high;
>>>>   		nvidia,sys-clock-req-active-high;
>>>> +
>>>> +		nvidia,thermtrip-pmu-i2c-addr = <0x40>;
>>>> +		nvidia,thermtrip-i2c-controller = <4>;
>>>> +		nvidia,thermtrip-reg-addr = <0x36>;
>>>> +		nvidia,thermtrip-reg-data = <0x2>;
>>>
>>> Given the number of properties that this can potentially have, I wonder
>>> if perhaps it would be a good idea to put this into a subnode, like
>>> this:
>>>
>>> 		thermtrip {
>>> 			pmu-i2c-addr = <0x40>;
>>> 			i2c-controller = <4>;
>>> 			...
>>> 		};
>>
>> I guess that'd look a bit nicer.
>
> Mind you, this may be somewhat on the edge of what's considered good
> practice for DT content, so maybe wait for a second opinion before going
> ahead with this.
>
> I don't have any objections to a set of nvidia,thermtrip-* properties, I
> just think it's fairly redundant to keep repeating that prefix (and it
> causes ugliness in drivers, too).

Hmm, ok. I'll fix the other stuff first.

>
> Thierry
>
> * Unknown Key
> * 0x7F3EB3A1
>

  reply	other threads:[~2014-08-13  8:06 UTC|newest]

Thread overview: 65+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-08-05  8:12 [PATCH 0/3] Thermal reset support in PMC Mikko Perttunen
2014-08-05  8:12 ` Mikko Perttunen
2014-08-05  8:12 ` Mikko Perttunen
2014-08-05  8:12 ` [PATCH 1/3] of: Add descriptions of thermtrip properties to Tegra PMC bindings Mikko Perttunen
2014-08-05  8:12   ` Mikko Perttunen
2014-08-05  8:12   ` Mikko Perttunen
     [not found]   ` <1407226380-747-2-git-send-email-mperttunen-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2014-08-13  7:35     ` Thierry Reding
2014-08-13  7:35       ` Thierry Reding
2014-08-13  7:35       ` Thierry Reding
2014-08-13  7:51       ` Mikko Perttunen
2014-08-13  7:51         ` Mikko Perttunen
2014-08-13  7:51         ` Mikko Perttunen
2014-08-13  8:01         ` Thierry Reding
2014-08-13  8:01           ` Thierry Reding
2014-08-05  8:12 ` [PATCH 2/3] ARM: tegra: Add PMC thermtrip programming to Jetson TK1 device tree Mikko Perttunen
2014-08-05  8:12   ` Mikko Perttunen
2014-08-05  8:12   ` Mikko Perttunen
     [not found]   ` <1407226380-747-3-git-send-email-mperttunen-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2014-08-13  7:37     ` Thierry Reding
2014-08-13  7:37       ` Thierry Reding
2014-08-13  7:37       ` Thierry Reding
2014-08-13  7:52       ` Mikko Perttunen
2014-08-13  7:52         ` Mikko Perttunen
2014-08-13  7:52         ` Mikko Perttunen
2014-08-13  8:03         ` Thierry Reding
2014-08-13  8:03           ` Thierry Reding
2014-08-13  8:06           ` Mikko Perttunen [this message]
2014-08-13  8:06             ` Mikko Perttunen
2014-08-13  8:06             ` Mikko Perttunen
2014-08-05  8:13 ` [PATCH 3/3] ARM: tegra: Add thermal reset (thermtrip) support to PMC Mikko Perttunen
2014-08-05  8:13   ` Mikko Perttunen
2014-08-05  8:13   ` Mikko Perttunen
     [not found]   ` <1407226380-747-4-git-send-email-mperttunen-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2014-08-13  7:53     ` Thierry Reding
2014-08-13  7:53       ` Thierry Reding
2014-08-13  7:53       ` Thierry Reding
2014-08-13  8:05       ` Mikko Perttunen
2014-08-13  8:05         ` Mikko Perttunen
2014-08-13 10:10     ` Wei Ni
2014-08-13 10:10       ` Wei Ni
2014-08-13 10:10       ` Wei Ni
     [not found] ` <1407226380-747-1-git-send-email-mperttunen-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2014-08-13  8:07   ` [PATCH 0/3] Thermal reset support in PMC Thierry Reding
2014-08-13  8:07     ` Thierry Reding
2014-08-13  8:07     ` Thierry Reding
2014-08-13  8:12     ` Mikko Perttunen
2014-08-13  8:12       ` Mikko Perttunen
2014-08-13  8:12       ` Mikko Perttunen
     [not found]       ` <53EB1DF5.301-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2014-08-13  8:42         ` Mikko Perttunen
2014-08-13  8:42           ` Mikko Perttunen
2014-08-13  8:42           ` Mikko Perttunen
     [not found]           ` <53EB250D.5070207-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2014-08-13  8:57             ` Thierry Reding
2014-08-13  8:57               ` Thierry Reding
2014-08-13  8:57               ` Thierry Reding
2014-08-13  9:52               ` Mikko Perttunen
2014-08-13  9:52                 ` Mikko Perttunen
2014-08-13  9:52                 ` Mikko Perttunen
2014-08-13 10:36                 ` Thierry Reding
2014-08-13 10:36                   ` Thierry Reding
2014-08-13 10:41                   ` Mikko Perttunen
2014-08-13 10:41                     ` Mikko Perttunen
2014-08-13 10:41                     ` Mikko Perttunen
     [not found]                     ` <53EB40F0.4000300-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2014-08-13 10:53                       ` Thierry Reding
2014-08-13 10:53                         ` Thierry Reding
2014-08-13 10:53                         ` Thierry Reding
2014-08-13 10:59                         ` Mikko Perttunen
2014-08-13 10:59                           ` Mikko Perttunen
2014-08-13 10:59                           ` Mikko Perttunen

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=53EB1C76.2000702@nvidia.com \
    --to=mperttunen-ddmlm1+adcrqt0dzr+alfa@public.gmane.org \
    --cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
    --cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org \
    --cc=thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.