* [PATCHv2 linux-wpan] ieee802154: mrf24j40: Add support for MRF24J40MC @ 2014-08-14 16:52 Simon Vincent 2014-08-14 18:10 ` Alexander Aring 0 siblings, 1 reply; 3+ messages in thread From: Simon Vincent @ 2014-08-14 16:52 UTC (permalink / raw) To: alex.aring, linux-zigbee-devel; +Cc: linux-wpan, simon.vincent The MRF24J40MC module has an external amplifier which should be enabled. Signed-off-by: Simon Vincent <simon.vincent@xsilon.com> --- drivers/net/ieee802154/mrf24j40.c | 40 +++++++++++++++++++++++++++++++++++++-- 1 file changed, 38 insertions(+), 2 deletions(-) diff --git a/drivers/net/ieee802154/mrf24j40.c b/drivers/net/ieee802154/mrf24j40.c index 9e6a124..7950d01 100644 --- a/drivers/net/ieee802154/mrf24j40.c +++ b/drivers/net/ieee802154/mrf24j40.c @@ -43,6 +43,8 @@ #define REG_TXSTBL 0x2E /* TX Stabilization */ #define REG_INTSTAT 0x31 /* Interrupt Status */ #define REG_INTCON 0x32 /* Interrupt Control */ +#define REG_GPIO 0x33 /* GPIO */ +#define REG_TRISGPIO 0x34 /* GPIO direction */ #define REG_RFCTL 0x36 /* RF Control Mode Register */ #define REG_BBREG1 0x39 /* Baseband Registers */ #define REG_BBREG2 0x3A /* */ @@ -63,6 +65,7 @@ #define REG_SLPCON1 0x220 #define REG_WAKETIMEL 0x222 /* Wake-up Time Match Value Low */ #define REG_WAKETIMEH 0x223 /* Wake-up Time Match Value High */ +#define REG_TESTMODE 0x22F /* Test mode */ #define REG_RX_FIFO 0x300 /* Receive FIFO */ /* Device configuration: Only channels 11-26 on page 0 are supported. */ @@ -75,6 +78,8 @@ #define RX_FIFO_SIZE 144 /* From datasheet */ #define SET_CHANNEL_DELAY_US 192 /* From datasheet */ +enum mrf24j40_modules { MRF24J40, MRF24J40MA, MRF24J40MC }; + /* Device Private Data */ struct mrf24j40 { struct spi_device *spi; @@ -690,6 +695,35 @@ static int mrf24j40_hw_init(struct mrf24j40 *devrec) if (ret) goto err_ret; + if (spi_get_device_id(devrec->spi)->driver_data == MRF24J40MC) { + /* Enable external amplifier */ + ret = write_long_reg(devrec, REG_TESTMODE, 0xF); + if (ret) + goto err_ret; + + ret = read_short_reg(devrec, REG_TRISGPIO, &val); + if (ret) + goto err_ret; + + val |= 0x8; + ret = write_short_reg(devrec, REG_TRISGPIO, val); + if (ret) + goto err_ret; + + ret = read_short_reg(devrec, REG_GPIO, &val); + if (ret) + goto err_ret; + + val |= 0x8; + ret = write_short_reg(devrec, REG_GPIO, val); + if (ret) + goto err_ret; + + ret = write_long_reg(devrec, REG_RFCON3, 0x28); + if (ret) + goto err_ret; + } + return 0; err_ret: @@ -778,8 +813,9 @@ static int mrf24j40_remove(struct spi_device *spi) } static const struct spi_device_id mrf24j40_ids[] = { - { "mrf24j40", 0 }, - { "mrf24j40ma", 0 }, + { "mrf24j40", MRF24J40 }, + { "mrf24j40ma", MRF24J40MA }, + { "mrf24j40mc", MRF24J40MC }, { }, }; MODULE_DEVICE_TABLE(spi, mrf24j40_ids); -- 1.9.1 ^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCHv2 linux-wpan] ieee802154: mrf24j40: Add support for MRF24J40MC 2014-08-14 16:52 [PATCHv2 linux-wpan] ieee802154: mrf24j40: Add support for MRF24J40MC Simon Vincent @ 2014-08-14 18:10 ` Alexander Aring 2014-08-16 15:49 ` Alan Ott 0 siblings, 1 reply; 3+ messages in thread From: Alexander Aring @ 2014-08-14 18:10 UTC (permalink / raw) To: Simon Vincent; +Cc: linux-zigbee-devel, linux-wpan, alan Hi, On Thu, Aug 14, 2014 at 05:52:46PM +0100, Simon Vincent wrote: > The MRF24J40MC module has an external amplifier which should be enabled. > > Signed-off-by: Simon Vincent <simon.vincent@xsilon.com> > --- > drivers/net/ieee802154/mrf24j40.c | 40 +++++++++++++++++++++++++++++++++++++-- > 1 file changed, 38 insertions(+), 2 deletions(-) > > diff --git a/drivers/net/ieee802154/mrf24j40.c b/drivers/net/ieee802154/mrf24j40.c > index 9e6a124..7950d01 100644 > --- a/drivers/net/ieee802154/mrf24j40.c > +++ b/drivers/net/ieee802154/mrf24j40.c > @@ -43,6 +43,8 @@ > #define REG_TXSTBL 0x2E /* TX Stabilization */ > #define REG_INTSTAT 0x31 /* Interrupt Status */ > #define REG_INTCON 0x32 /* Interrupt Control */ > +#define REG_GPIO 0x33 /* GPIO */ > +#define REG_TRISGPIO 0x34 /* GPIO direction */ > #define REG_RFCTL 0x36 /* RF Control Mode Register */ > #define REG_BBREG1 0x39 /* Baseband Registers */ > #define REG_BBREG2 0x3A /* */ > @@ -63,6 +65,7 @@ > #define REG_SLPCON1 0x220 > #define REG_WAKETIMEL 0x222 /* Wake-up Time Match Value Low */ > #define REG_WAKETIMEH 0x223 /* Wake-up Time Match Value High */ > +#define REG_TESTMODE 0x22F /* Test mode */ > #define REG_RX_FIFO 0x300 /* Receive FIFO */ > > /* Device configuration: Only channels 11-26 on page 0 are supported. */ > @@ -75,6 +78,8 @@ > #define RX_FIFO_SIZE 144 /* From datasheet */ > #define SET_CHANNEL_DELAY_US 192 /* From datasheet */ > > +enum mrf24j40_modules { MRF24J40, MRF24J40MA, MRF24J40MC }; > + > /* Device Private Data */ > struct mrf24j40 { > struct spi_device *spi; > @@ -690,6 +695,35 @@ static int mrf24j40_hw_init(struct mrf24j40 *devrec) > if (ret) > goto err_ret; > > + if (spi_get_device_id(devrec->spi)->driver_data == MRF24J40MC) { > + /* Enable external amplifier */ > + ret = write_long_reg(devrec, REG_TESTMODE, 0xF); > + if (ret) > + goto err_ret; > + > + ret = read_short_reg(devrec, REG_TRISGPIO, &val); > + if (ret) > + goto err_ret; > + > + val |= 0x8; > + ret = write_short_reg(devrec, REG_TRISGPIO, val); > + if (ret) > + goto err_ret; > + > + ret = read_short_reg(devrec, REG_GPIO, &val); > + if (ret) > + goto err_ret; > + > + val |= 0x8; > + ret = write_short_reg(devrec, REG_GPIO, val); > + if (ret) > + goto err_ret; > + > + ret = write_long_reg(devrec, REG_RFCON3, 0x28); > + if (ret) > + goto err_ret; > + } > + > return 0; > > err_ret: > @@ -778,8 +813,9 @@ static int mrf24j40_remove(struct spi_device *spi) > } > > static const struct spi_device_id mrf24j40_ids[] = { > - { "mrf24j40", 0 }, > - { "mrf24j40ma", 0 }, > + { "mrf24j40", MRF24J40 }, > + { "mrf24j40ma", MRF24J40MA }, > + { "mrf24j40mc", MRF24J40MC }, > { }, > }; > MODULE_DEVICE_TABLE(spi, mrf24j40_ids); > -- > 1.9.1 > I will apply this patch, but I cc the original author of this driver Alan Ott. Alan is this patch okay for you? If you don't respond in the next two days I assume "yes". - Alex ^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCHv2 linux-wpan] ieee802154: mrf24j40: Add support for MRF24J40MC 2014-08-14 18:10 ` Alexander Aring @ 2014-08-16 15:49 ` Alan Ott 0 siblings, 0 replies; 3+ messages in thread From: Alan Ott @ 2014-08-16 15:49 UTC (permalink / raw) To: Alexander Aring, Simon Vincent; +Cc: linux-zigbee-devel, linux-wpan On 08/14/2014 02:10 PM, Alexander Aring wrote: > Hi, > > On Thu, Aug 14, 2014 at 05:52:46PM +0100, Simon Vincent wrote: >> The MRF24J40MC module has an external amplifier which should be enabled. >> >> Signed-off-by: Simon Vincent <simon.vincent@xsilon.com> >> --- >> drivers/net/ieee802154/mrf24j40.c | 40 +++++++++++++++++++++++++++++++++++++-- >> 1 file changed, 38 insertions(+), 2 deletions(-) >> >> diff --git a/drivers/net/ieee802154/mrf24j40.c b/drivers/net/ieee802154/mrf24j40.c >> index 9e6a124..7950d01 100644 >> --- a/drivers/net/ieee802154/mrf24j40.c >> +++ b/drivers/net/ieee802154/mrf24j40.c >> @@ -43,6 +43,8 @@ >> #define REG_TXSTBL 0x2E /* TX Stabilization */ >> #define REG_INTSTAT 0x31 /* Interrupt Status */ >> #define REG_INTCON 0x32 /* Interrupt Control */ >> +#define REG_GPIO 0x33 /* GPIO */ >> +#define REG_TRISGPIO 0x34 /* GPIO direction */ >> #define REG_RFCTL 0x36 /* RF Control Mode Register */ >> #define REG_BBREG1 0x39 /* Baseband Registers */ >> #define REG_BBREG2 0x3A /* */ >> @@ -63,6 +65,7 @@ >> #define REG_SLPCON1 0x220 >> #define REG_WAKETIMEL 0x222 /* Wake-up Time Match Value Low */ >> #define REG_WAKETIMEH 0x223 /* Wake-up Time Match Value High */ >> +#define REG_TESTMODE 0x22F /* Test mode */ >> #define REG_RX_FIFO 0x300 /* Receive FIFO */ >> >> /* Device configuration: Only channels 11-26 on page 0 are supported. */ >> @@ -75,6 +78,8 @@ >> #define RX_FIFO_SIZE 144 /* From datasheet */ >> #define SET_CHANNEL_DELAY_US 192 /* From datasheet */ >> >> +enum mrf24j40_modules { MRF24J40, MRF24J40MA, MRF24J40MC }; >> + >> /* Device Private Data */ >> struct mrf24j40 { >> struct spi_device *spi; >> @@ -690,6 +695,35 @@ static int mrf24j40_hw_init(struct mrf24j40 *devrec) >> if (ret) >> goto err_ret; >> >> + if (spi_get_device_id(devrec->spi)->driver_data == MRF24J40MC) { >> + /* Enable external amplifier */ >> + ret = write_long_reg(devrec, REG_TESTMODE, 0xF); >> + if (ret) >> + goto err_ret; >> + >> + ret = read_short_reg(devrec, REG_TRISGPIO, &val); >> + if (ret) >> + goto err_ret; >> + >> + val |= 0x8; >> + ret = write_short_reg(devrec, REG_TRISGPIO, val); >> + if (ret) >> + goto err_ret; >> + >> + ret = read_short_reg(devrec, REG_GPIO, &val); >> + if (ret) >> + goto err_ret; >> + >> + val |= 0x8; >> + ret = write_short_reg(devrec, REG_GPIO, val); >> + if (ret) >> + goto err_ret; >> + >> + ret = write_long_reg(devrec, REG_RFCON3, 0x28); >> + if (ret) >> + goto err_ret; As I've mentioned before on this list[1], it's a waste of code space to check for return values from SPI transfers, because in the kernel, we assume that they succeed, in the same way that we assume that writes to memory addresses succeed[2]. There are also some magic numbers in there. I get setting the TRIS and GPIO single bits, that's fine. What about TESTMODE and RFCON3? What do 0xf and 0x28 mean? If they came directly from the datasheet, cite the section it comes from (like I do in the initialization). >> + } >> + >> return 0; >> >> err_ret: >> @@ -778,8 +813,9 @@ static int mrf24j40_remove(struct spi_device *spi) >> } >> >> static const struct spi_device_id mrf24j40_ids[] = { >> - { "mrf24j40", 0 }, >> - { "mrf24j40ma", 0 }, >> + { "mrf24j40", MRF24J40 }, >> + { "mrf24j40ma", MRF24J40MA }, >> + { "mrf24j40mc", MRF24J40MC }, Good. I like this mechanism, and it will be very easy to add the MB as well when the time comes. >> { }, >> }; >> MODULE_DEVICE_TABLE(spi, mrf24j40_ids); >> -- >> 1.9.1 >> > I will apply this patch, but I cc the original author of this driver Alan Ott. > > Alan is this patch okay for you? If you don't respond in the next two days I > assume "yes". > Thanks Simon, for the patch, and sorry for my long delay in reviewing it. Alan. [1] https://www.mail-archive.com/linux-zigbee-devel%40lists.sourceforge.net/msg02898.html [2] It was a while ago, so I'm not blaming you for not seeing it, and I see that you made it the way you did because it matched the code in net-next, but the reason the code is the way it is now, is that someone went around me to get a patch applied (which I had previously rejected) to make it look this way. That's a separate issue, but explains why I disagree with code which matches code that's already in the driver. ^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2014-08-16 15:49 UTC | newest] Thread overview: 3+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2014-08-14 16:52 [PATCHv2 linux-wpan] ieee802154: mrf24j40: Add support for MRF24J40MC Simon Vincent 2014-08-14 18:10 ` Alexander Aring 2014-08-16 15:49 ` Alan Ott
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.