From: Stefano Babic <sbabic@denx.de>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 11/11] imx: ventana: leave PCI reset de-asserted if PCI enabled
Date: Wed, 20 Aug 2014 13:05:23 +0200 [thread overview]
Message-ID: <53F480F3.2020800@denx.de> (raw)
In-Reply-To: <1407476151-5603-12-git-send-email-tharvey@gateworks.com>
Hi Tim,
On 08/08/2014 07:35, Tim Harvey wrote:
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
> ---
> board/gateworks/gw_ventana/gw_ventana.c | 8 +++-----
> 1 file changed, 3 insertions(+), 5 deletions(-)
>
> diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c
> index 1c24e4b..70b90d8 100644
> --- a/board/gateworks/gw_ventana/gw_ventana.c
> +++ b/board/gateworks/gw_ventana/gw_ventana.c
> @@ -991,12 +991,10 @@ static void setup_board_gpio(int board)
> gpio_direction_output(GP_MSATA_SEL, 0);
> }
>
> - /*
> - * assert PCI_RST# (released by OS when clock is valid)
> - * TODO: figure out why leaving this de-asserted from PCI scan on boot
> - * causes linux pcie driver to hang during enumeration
> - */
> +#if !defined(CONFIG_CMD_PCI)
> + /* assert PCI_RST# (released by OS when clock is valid) */
> gpio_direction_output(gpio_cfg[board].pcie_rst, 0);
> +#endif
>
> /* turn off (active-high) user LED's */
> for (i = 0; i < 4; i++) {
>
Applied to u-boot-imx, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
prev parent reply other threads:[~2014-08-20 11:05 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-08-08 5:35 [U-Boot] [PATCH 00/11] imx: ventana: misc patches Tim Harvey
2014-08-08 5:35 ` [U-Boot] [PATCH 01/11] imx: ventana: set dynamic env var for flash layout Tim Harvey
2014-08-20 10:52 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 02/11] imx: ventana: added cputype env var Tim Harvey
2014-08-14 15:23 ` Stefano Babic
2014-08-18 13:52 ` Tim Harvey
2014-08-20 10:51 ` Stefano Babic
2014-09-09 13:19 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 03/11] imx: ventana: remove caam disable per eeprom bit Tim Harvey
2014-08-20 10:53 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 04/11] imx: ventana: add appropriate delay following GSC i2c write Tim Harvey
2014-08-20 10:54 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 05/11] imx: ventana: add econfig command Tim Harvey
2014-08-20 11:09 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 06/11] imx: ventana: add video enable gpio pinmux for GW54xx Tim Harvey
2014-08-20 10:59 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 07/11] imx: ventana: add missing crlf to print Tim Harvey
2014-08-20 11:00 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 08/11] imx: ventana: configure i2c_dis# pin properly for gw53xx Tim Harvey
2014-08-20 11:02 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 09/11] imx: ventana: enable SION bit on gpio outputs Tim Harvey
2014-08-20 11:02 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 10/11] imx: ventana: add iomux for PCISKT_WDIS# gpio Tim Harvey
2014-08-20 11:03 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 11/11] imx: ventana: leave PCI reset de-asserted if PCI enabled Tim Harvey
2014-08-20 11:05 ` Stefano Babic [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=53F480F3.2020800@denx.de \
--to=sbabic@denx.de \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.