* [meta-fsl-arm-extra][PATCH] linux-boundary (3.10.17): update to 62ef71f
@ 2014-08-27 10:19 Christoph Settgast
2014-08-27 12:32 ` Otavio Salvador
0 siblings, 1 reply; 6+ messages in thread
From: Christoph Settgast @ 2014-08-27 10:19 UTC (permalink / raw)
To: meta-freescale
This includes the following changes, the defconfig
changes are reflected in the yocto defconfigs to
keep things in sync.
Eric Nelson (39):
nit6xlite_defconfig: add LEDS_GPIO
sabrelite: configure ethernet PHY nRST
nitrogen6x: configure ethernet PHY nRST
nitrogen6_mtp: configure ethernet PHY nRST
nitrogen6_max: configure ethernet PHY nRST
nit6xlite: configure ethernet PHY nRST
nit6xlite: default to multi-touch input for eGalax, ft5x06
nitrogen6x: default to multi-touch input for eGalax, ft5x06
nitrogen6x_ub: default to multi-touch input for eGalax, ft5x06
ft5x06: free GPIO in _remove
ft5x06: add support for ABS_MT_TRACKING_ID
ft5x06: set MAX_TOUCHES to 12
ft5x06: respect/return tracking id from controller
net: fec: iMX6 FEC does not support half-duplex gigabit
nit*_defconfig: add CONFIG_USB_FUNCTIONFS=m
nit*_defconfig: add CONFIG_USB_SERIAL_GENERIC
nit6xlite: add ili210x touch controller
nitrogen6x: add ili210x touch controller
sabrelite: add ili210x touch controller
nitrogen6_max: add ili210x touch controller
nit6xlite_defconfig: add ILI210X touch screen
nitrogen6x_defconfig: add ILI210X touch screen
ili210x: Allow use with Device Tree
nitrogen6_max: enable FEC ethernet
nitrogen6_max: swap NANDF_CS0/1 (GP6:11/14) for SD3 voltage select, WL IRQ
nitrogen6_max: define ENET_TXD1 as GPIO1:29 for amplifier mute
flexcan: allow use with transceivers that only have standby pin
nitrogen6x: SDIO is 1.8V-only, add flag in DTS
sdhci: Allow platform_set_power callback
sdhci-imx: Add power-gpio support
nitrogen6x: use power-gpio instead of vqmmc-supply to control WL_EN pin
nitrogen6_max: use power-gpio instead of vqmmc-supply to control WL_EN pin
nitrogen6_max: configure voltage-select pin
nit6xlite: flag 1.8v quirk for vqmmc on sdhc2 (WiFi interface)
DT:imx6qdl: Pad SD2_DAT3 should have pull-down
nitrogen6x_defconfig: include LEDS_PWM, SPI_SPIDEV
Add imx6q-sabrelite-nolcd device tree
fec: Add disable_giga parameter to force 10/100 operation
Revert "DT:imx6qdl: Pad SD2_DAT3 should have pull-down"
Ranjani Vaidyanathan (1):
ENGR00318392 ARM:imx6x: Save/restore SCU and some CP15 registers across suspend/resume
Signed-off-by: Christoph Settgast <christoph.settgast@methodpark.de>
---
.../nitrogen6x-lite/defconfig | 6 ++++--
.../linux-boundary-3.10.17/nitrogen6x/defconfig | 7 +++++--
recipes-kernel/linux/linux-boundary_3.10.17.bb | 2 +-
3 files changed, 10 insertions(+), 5 deletions(-)
diff --git a/recipes-kernel/linux/linux-boundary-3.10.17/nitrogen6x-lite/defconfig b/recipes-kernel/linux/linux-boundary-3.10.17/nitrogen6x-lite/defconfig
index c077a5f..3d33c82 100644
--- a/recipes-kernel/linux/linux-boundary-3.10.17/nitrogen6x-lite/defconfig
+++ b/recipes-kernel/linux/linux-boundary-3.10.17/nitrogen6x-lite/defconfig
@@ -133,9 +133,8 @@ CONFIG_KEYBOARD_IMX=y
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_AR1020_I2C=y
CONFIG_TOUCHSCREEN_EGALAX=y
-CONFIG_TOUCHSCREEN_EGALAX_SINGLE_TOUCH=y
CONFIG_TOUCHSCREEN_FT5X06=y
-CONFIG_TOUCHSCREEN_FT5X06_SINGLE_TOUCH=y
+CONFIG_TOUCHSCREEN_ILI210X=y
CONFIG_TOUCHSCREEN_TSC2004=y
CONFIG_SERIO_SERPORT=m
CONFIG_VT_HW_CONSOLE_BINDING=y
@@ -216,6 +215,7 @@ CONFIG_USB_CHIPIDEA=y
CONFIG_USB_CHIPIDEA_UDC=y
CONFIG_USB_CHIPIDEA_HOST=y
CONFIG_USB_SERIAL=y
+CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_CP210X=y
CONFIG_USB_SERIAL_FTDI_SIO=y
CONFIG_USB_SERIAL_KEYSPAN=y
@@ -227,6 +227,7 @@ CONFIG_USB_MXS_PHY=y
CONFIG_USB_GADGET=y
CONFIG_USB_ZERO=m
CONFIG_USB_ETH=m
+CONFIG_USB_FUNCTIONFS=m
CONFIG_USB_MASS_STORAGE=m
CONFIG_USB_G_SERIAL=m
CONFIG_USB_G_MULTI=m
@@ -240,6 +241,7 @@ CONFIG_MXC_GPU_VIV=y
CONFIG_MXC_ASRC=y
CONFIG_MXC_MIPI_CSI2=y
CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_INTF_DEV_UIE_EMUL=y
CONFIG_RTC_DRV_ISL1208=y
diff --git a/recipes-kernel/linux/linux-boundary-3.10.17/nitrogen6x/defconfig b/recipes-kernel/linux/linux-boundary-3.10.17/nitrogen6x/defconfig
index 810d040..00ff4b2 100644
--- a/recipes-kernel/linux/linux-boundary-3.10.17/nitrogen6x/defconfig
+++ b/recipes-kernel/linux/linux-boundary-3.10.17/nitrogen6x/defconfig
@@ -139,9 +139,8 @@ CONFIG_KEYBOARD_IMX=y
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_AR1020_I2C=y
CONFIG_TOUCHSCREEN_EGALAX=y
-CONFIG_TOUCHSCREEN_EGALAX_SINGLE_TOUCH=y
CONFIG_TOUCHSCREEN_FT5X06=y
-CONFIG_TOUCHSCREEN_FT5X06_SINGLE_TOUCH=y
+CONFIG_TOUCHSCREEN_ILI210X=y
CONFIG_TOUCHSCREEN_TSC2004=y
CONFIG_SERIO_SERPORT=m
CONFIG_VT_HW_CONSOLE_BINDING=y
@@ -161,6 +160,7 @@ CONFIG_I2C_ALGOPCA=m
CONFIG_I2C_IMX=y
CONFIG_SPI=y
CONFIG_SPI_IMX=y
+CONFIG_SPI_SPIDEV=y
CONFIG_GPIO_SYSFS=y
CONFIG_POWER_SUPPLY=y
CONFIG_SENSORS_MAG3110=y
@@ -229,6 +229,7 @@ CONFIG_USB_CHIPIDEA=y
CONFIG_USB_CHIPIDEA_UDC=y
CONFIG_USB_CHIPIDEA_HOST=y
CONFIG_USB_SERIAL=y
+CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_CP210X=y
CONFIG_USB_SERIAL_FTDI_SIO=y
CONFIG_USB_SERIAL_KEYSPAN=y
@@ -240,6 +241,7 @@ CONFIG_USB_MXS_PHY=y
CONFIG_USB_GADGET=y
CONFIG_USB_ZERO=m
CONFIG_USB_ETH=m
+CONFIG_USB_FUNCTIONFS=m
CONFIG_USB_MASS_STORAGE=m
CONFIG_USB_G_SERIAL=m
CONFIG_USB_G_MULTI=m
@@ -253,6 +255,7 @@ CONFIG_MXC_GPU_VIV=y
CONFIG_MXC_ASRC=y
CONFIG_MXC_MIPI_CSI2=y
CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_PWM=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_INTF_DEV_UIE_EMUL=y
CONFIG_RTC_DRV_ISL1208=y
diff --git a/recipes-kernel/linux/linux-boundary_3.10.17.bb b/recipes-kernel/linux/linux-boundary_3.10.17.bb
index 15d3313..b5eb2ce 100644
--- a/recipes-kernel/linux/linux-boundary_3.10.17.bb
+++ b/recipes-kernel/linux/linux-boundary_3.10.17.bb
@@ -11,7 +11,7 @@ SRC_URI = "git://github.com/boundarydevices/linux-imx6.git;branch=${SRCBRANCH} \
LOCALVERSION = "-1.0.0_ga+yocto"
SRCBRANCH = "boundary-imx_3.10.17_1.0.0_ga"
-SRCREV = "ca882d5a8f09d4e0e7aecd754baab54bf04a8768"
+SRCREV = "62ef71f3f6dc199ecc533c5aea7a88b74e5bf449"
DEPENDS += "lzop-native "
COMPATIBLE_MACHINE = "(mx6)"
COMPATIBLE_MACHINE = "(nitrogen6x|nitrogen6x-lite)"
--
1.7.9.5
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [meta-fsl-arm-extra][PATCH] linux-boundary (3.10.17): update to 62ef71f
2014-08-27 10:19 [meta-fsl-arm-extra][PATCH] linux-boundary (3.10.17): update to 62ef71f Christoph Settgast
@ 2014-08-27 12:32 ` Otavio Salvador
2014-08-28 10:15 ` Christoph Settgast
0 siblings, 1 reply; 6+ messages in thread
From: Otavio Salvador @ 2014-08-27 12:32 UTC (permalink / raw)
To: Christoph Settgast, Eric Nelson; +Cc: meta-freescale@yoctoproject.org
On Wed, Aug 27, 2014 at 7:19 AM, Christoph Settgast
<christoph.settgast@methodpark.de> wrote:
> nit6xlite: default to multi-touch input for eGalax, ft5x06
> nitrogen6x: default to multi-touch input for eGalax, ft5x06
> nitrogen6x_ub: default to multi-touch input for eGalax, ft5x06
Has this been tested with Yocto Project?
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [meta-fsl-arm-extra][PATCH] linux-boundary (3.10.17): update to 62ef71f
2014-08-27 12:32 ` Otavio Salvador
@ 2014-08-28 10:15 ` Christoph Settgast
2014-08-28 10:22 ` Christoph Settgast
0 siblings, 1 reply; 6+ messages in thread
From: Christoph Settgast @ 2014-08-28 10:15 UTC (permalink / raw)
To: Otavio Salvador, Eric Nelson; +Cc: meta-freescale@yoctoproject.org
On 27.08.2014 14:32, Otavio Salvador wrote:
> On Wed, Aug 27, 2014 at 7:19 AM, Christoph Settgast
> <christoph.settgast@methodpark.de> wrote:
>> nit6xlite: default to multi-touch input for eGalax, ft5x06
>> nitrogen6x: default to multi-touch input for eGalax, ft5x06
>> nitrogen6x_ub: default to multi-touch input for eGalax, ft5x06
>
> Has this been tested with Yocto Project?
>
At least with Qt5 and its MultiPointTouchArea I get 5 touchpoints
simultaniously with the ft5x06, X11 backend.
But if there are negative experiences, please shout.
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [meta-fsl-arm-extra][PATCH] linux-boundary (3.10.17): update to 62ef71f
2014-08-28 10:15 ` Christoph Settgast
@ 2014-08-28 10:22 ` Christoph Settgast
2014-08-30 21:44 ` Otavio Salvador
0 siblings, 1 reply; 6+ messages in thread
From: Christoph Settgast @ 2014-08-28 10:22 UTC (permalink / raw)
To: Otavio Salvador, Eric Nelson; +Cc: meta-freescale@yoctoproject.org
On 28.08.2014 12:15, Christoph Settgast wrote:
> At least with Qt5 and its MultiPointTouchArea I get 5 touchpoints
> simultaniously with the ft5x06, X11 backend.
Forgot to mention: Tested on daisy branch of yocto.
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [meta-fsl-arm-extra][PATCH] linux-boundary (3.10.17): update to 62ef71f
2014-08-28 10:22 ` Christoph Settgast
@ 2014-08-30 21:44 ` Otavio Salvador
2014-08-31 16:56 ` Eric Nelson
0 siblings, 1 reply; 6+ messages in thread
From: Otavio Salvador @ 2014-08-30 21:44 UTC (permalink / raw)
To: Christoph Settgast; +Cc: meta-freescale@yoctoproject.org
On Thu, Aug 28, 2014 at 7:22 AM, Christoph Settgast
<christoph.settgast@methodpark.de> wrote:
> On 28.08.2014 12:15, Christoph Settgast wrote:
>>
>> At least with Qt5 and its MultiPointTouchArea I get 5 touchpoints
>> simultaniously with the ft5x06, X11 backend.
>
> Forgot to mention: Tested on daisy branch of yocto.
Makes sense.
Eric, can you review this one so I can apply it?
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [meta-fsl-arm-extra][PATCH] linux-boundary (3.10.17): update to 62ef71f
2014-08-30 21:44 ` Otavio Salvador
@ 2014-08-31 16:56 ` Eric Nelson
0 siblings, 0 replies; 6+ messages in thread
From: Eric Nelson @ 2014-08-31 16:56 UTC (permalink / raw)
To: Otavio Salvador, Christoph Settgast; +Cc: meta-freescale@yoctoproject.org
Thanks for the ping Otavio,
On 08/30/2014 02:44 PM, Otavio Salvador wrote:
> On Thu, Aug 28, 2014 at 7:22 AM, Christoph Settgast
> <christoph.settgast@methodpark.de> wrote:
>> On 28.08.2014 12:15, Christoph Settgast wrote:
>>>
>>> At least with Qt5 and its MultiPointTouchArea I get 5 touchpoints
>>> simultaniously with the ft5x06, X11 backend.
>>
>> Forgot to mention: Tested on daisy branch of yocto.
>
> Makes sense.
>
> Eric, can you review this one so I can apply it?
>
Reviewed-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Note that there are a couple of patches in this set that
affect users. The default kernel configurations no longer
default to single-touch operation for the FT5x06 touch
controllers used on our 1024x600 and 1280x800 panels,
or the eGalax touch controller on the 1024x768 Hannstar
panel.
The single-touch flag was added primarily to support the
use of tslib with Qt4. Qt5 can (and should) use multi-touch
support and I believe that's the right default for new
users.
Regards,
Eric
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2014-08-31 16:56 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-08-27 10:19 [meta-fsl-arm-extra][PATCH] linux-boundary (3.10.17): update to 62ef71f Christoph Settgast
2014-08-27 12:32 ` Otavio Salvador
2014-08-28 10:15 ` Christoph Settgast
2014-08-28 10:22 ` Christoph Settgast
2014-08-30 21:44 ` Otavio Salvador
2014-08-31 16:56 ` Eric Nelson
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.