From: poma <pomidorabelisima@gmail.com>
To: linux-wireless@vger.kernel.org,
Christian Lamparter <chunkeey@googlemail.com>,
Joshua Roys <Joshua.Roys@gtri.gatech.edu>,
Larry Finger <Larry.Finger@lwfinger.net>,
Realtek WlanFAE <wlanfae@realtek.com>,
lizhaoming <chaoming_li@realsil.com.cn>
Cc: Network Manager <networkmanager-list@gnome.org>
Subject: RTL8188SU(rtl8192su) - unavailable
Date: Mon, 29 Sep 2014 11:29:25 +0200 [thread overview]
Message-ID: <54292675.4090607@gmail.com> (raw)
- lsusb
0bda:8171 Realtek Semiconductor Corp. RTL8188SU 802.11n WLAN Adapter
- http://wireless.kernel.org/en/users/Drivers/rtl819x#staging_drivers
...
r8712u is a USB driver for RTL8712U/RTL8192SU devices, it's going to be replaced by rtl8192su.
- /etc/modprobe.d/blacklist-r8712u.conf
blacklist r8712u
- http://wireless.kernel.org/en/users/Drivers/rtl819x#rtlwifi
...
rtl8192su is a USB driver for RTL8712U/RTL8192SU devices. (WIP : http://github.com/chunkeey/rtl8192su )
- modulecomb
mac80211 - - rtl_usb -
\ / \
- rtlwifi - - rtl8192su
/ \ /
cfg80211 - - rtl8192s-common
- ls /usr/lib/modules/3.17.0-0.rc6.git2.1.fc22.x86_64/updates
rtl8192s-common.ko
rtl8192su.ko
rtl_usb.ko
rtlwifi.ko
- file /usr/lib/firmware/rtlwifi/rtl8192sufw.bin
/usr/lib/firmware/rtlwifi/rtl8192sufw.bin: symbolic link to `rtl8712u.bin'
- dmesg
rtlwifi: module verification failed: signature and/or required key missing - tainting kernel
rtl8192s_common: Chip version 0x3
rtl_usb: rx_max_size 9100, rx_urb_num 8, in_ep 3
rtl8192su: Power Save off (module option)
rtl8192su: FW Power Save off (module option)
rtl8192su: Driver for Realtek RTL8192SU/RTL8191SU
Loading firmware rtlwifi/rtl8192sufw.bin
usbcore: registered new interface driver rtl8192su
ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
rtl8192su 2-1:1.0 wlp0s4f1u1: renamed from wlan0
systemd-udevd[391]: renamed network interface wlan0 to wlp0s4f1u1
- nmcli radio
WIFI-HW WIFI WWAN-HW WWAN
enabled enabled enabled enabled
- journalctl NetworkManager(debug)
[platform/nm-platform.c:2565] log_link(): signal: link added: 4: wlp0s4f1u1 <DOWN> mtu 1500 wifi driver 'rtl8192su' udi '/sys/devices/pci0000:00/0000:00:04.1/usb2/2-1/2-1:1.0/net/wlp0s4f1u1'
[nm-device-wifi.c:228] constructor(): (wlp0s4f1u1): kernel ifindex 4
(wlp0s4f1u1): using nl80211 for WiFi device control
(wlp0s4f1u1): driver supports Access Point (AP) mode
[devices/nm-device.c:6983] nm_device_update_hw_address(): (wlp0s4f1u1): hardware address is 00:E0:4C:81:92:E4
[nm-device-wifi.c:2623] update_initial_hw_address(): (wlp0s4f1u1): read initial MAC address 00:E0:4C:81:92:E4
[platform/nm-linux-platform.c:2099] sysctl_get(): error reading /sys/class/net/wlp0s4f1u1/phys_port_id: Failed to read from file '/sys/class/net/wlp0s4f1u1/phys_port_id': Operation not supported
[nm-manager.c:1372] manager_rfkill_update_one_type(): WiFi hw-enabled 1 sw-enabled 1
[nm-device-wifi.c:3230] set_enabled(): (wlp0s4f1u1): device now enabled
[nm-device-wifi.c:3236] set_enabled(): (enable): wlp0s4f1u1 blocked by UNMANAGED state
(wlp0s4f1u1): new 802.11 WiFi device (driver: 'rtl8192su' ifindex: 4)
(wlp0s4f1u1): exported as /org/freedesktop/NetworkManager/Devices/1
[devices/nm-device.c:5089] nm_device_set_ip4_config(): (wlp0s4f1u1): set IP4Config instance (/org/freedesktop/NetworkManager/IP4Config/0)
[devices/nm-device.c:5197] nm_device_set_ip6_config(): (wlp0s4f1u1): set IP6Config instance (/org/freedesktop/NetworkManager/IP6Config/0)
(wlp0s4f1u1): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2]
[platform/nm-linux-platform.c:2067] _log_dbg_sysctl_get_impl(): sysctl: reading '/proc/sys/net/ipv6/conf/wlp0s4f1u1/accept_ra': '1'
[platform/nm-linux-platform.c:2067] _log_dbg_sysctl_get_impl(): sysctl: reading '/proc/sys/net/ipv6/conf/wlp0s4f1u1/accept_ra_defrtr': '1'
[platform/nm-linux-platform.c:2067] _log_dbg_sysctl_get_impl(): sysctl: reading '/proc/sys/net/ipv6/conf/wlp0s4f1u1/accept_ra_pinfo': '1'
[platform/nm-linux-platform.c:2067] _log_dbg_sysctl_get_impl(): sysctl: reading '/proc/sys/net/ipv6/conf/wlp0s4f1u1/accept_ra_rtr_pref': '1'
[platform/nm-linux-platform.c:2067] _log_dbg_sysctl_get_impl(): sysctl: reading '/proc/sys/net/ipv6/conf/wlp0s4f1u1/disable_ipv6': '0'
[platform/nm-linux-platform.c:2067] _log_dbg_sysctl_get_impl(): sysctl: reading '/proc/sys/net/ipv6/conf/wlp0s4f1u1/hop_limit': '64'
[platform/nm-linux-platform.c:2067] _log_dbg_sysctl_get_impl(): sysctl: reading '/proc/sys/net/ipv6/conf/wlp0s4f1u1/use_tempaddr': '0'
[platform/nm-linux-platform.c:1967] _log_dbg_sysctl_set_impl(): sysctl: setting '/proc/sys/net/ipv6/conf/wlp0s4f1u1/disable_ipv6' to '1' (current value is '0')
[platform/nm-linux-platform.c:1967] _log_dbg_sysctl_set_impl(): sysctl: setting '/proc/sys/net/ipv6/conf/wlp0s4f1u1/accept_ra_defrtr' to '0' (current value is '1')
[platform/nm-linux-platform.c:1967] _log_dbg_sysctl_set_impl(): sysctl: setting '/proc/sys/net/ipv6/conf/wlp0s4f1u1/accept_ra_pinfo' to '0' (current value is '1')
[platform/nm-linux-platform.c:1967] _log_dbg_sysctl_set_impl(): sysctl: setting '/proc/sys/net/ipv6/conf/wlp0s4f1u1/accept_ra_rtr_pref' to '0' (current value is '1')
[platform/nm-linux-platform.c:1965] _log_dbg_sysctl_set_impl(): sysctl: setting '/proc/sys/net/ipv6/conf/wlp0s4f1u1/use_tempaddr' to '0' (current value is identical)
[devices/nm-device.c:5542] nm_device_bring_up(): (wlp0s4f1u1): bringing up device.
[platform/nm-platform.c:806] nm_platform_link_set_up(): link: setting up 'wlp0s4f1u1' (4)
[platform/nm-linux-platform.c:2356] link_change_flags(): link: change 4: flags set 'up' (1)
[platform/nm-linux-platform.c:2250] link_change(): Netlink error changing link 4: <UP> mtu 0 (1) driver 'rtl8192su' udi '/sys/devices/pci0000:00/0000:00:04.1/usb2/2-1/2-1:1.0/net/wlp0s4f1u1': No such device
(wlp0s4f1u1): preparing device
[devices/nm-device.c:6396] nm_device_remove_pending_action(): (wlp0s4f1u1): remove_pending_action (0): 'autoconf6' not pending (expected)
[platform/nm-linux-platform.c:1965] _log_dbg_sysctl_set_impl(): sysctl: setting '/proc/sys/net/ipv6/conf/wlp0s4f1u1/disable_ipv6' to '1' (current value is identical)
[platform/nm-linux-platform.c:1967] _log_dbg_sysctl_set_impl(): sysctl: setting '/proc/sys/net/ipv6/conf/wlp0s4f1u1/accept_ra' to '0' (current value is '1')
[platform/nm-linux-platform.c:1965] _log_dbg_sysctl_set_impl(): sysctl: setting '/proc/sys/net/ipv6/conf/wlp0s4f1u1/use_tempaddr' to '0' (current value is identical)
[devices/nm-device.c:7024] nm_device_set_hw_addr(): (wlp0s4f1u1): no MAC address change needed
[devices/nm-device.c:5095] nm_device_set_ip4_config(): (wlp0s4f1u1): clear IP4Config instance (/org/freedesktop/NetworkManager/IP4Config/0)
[devices/nm-device.c:5203] nm_device_set_ip6_config(): (wlp0s4f1u1): clear IP6Config instance (/org/freedesktop/NetworkManager/IP6Config/0)
[supplicant-manager/nm-supplicant-manager.c:90] nm_supplicant_manager_iface_get(): (wlp0s4f1u1): creating new supplicant interface
[supplicant-manager/nm-supplicant-interface.c:881] interface_add(): (wlp0s4f1u1): adding interface to supplicant
[devices/nm-device.c:6342] nm_device_add_pending_action(): (wlp0s4f1u1): add_pending_action (1): 'waiting for supplicant'
[nm-manager.c:718] check_if_startup_complete(): check_if_startup_complete returns FALSE because of wlp0s4f1u1
[nm-device-wifi.c:1192] is_available(): (wlp0s4f1u1): not available because supplicant interface not ready
[devices/nm-device.c:6705] _set_state_full(): (wlp0s4f1u1): device not yet available for transition to DISCONNECTED
[nm-manager.c:718] check_if_startup_complete(): check_if_startup_complete returns FALSE because of wlp0s4f1u1
[devices/nm-device.c:6342] nm_device_add_pending_action(): (wlp0s4f1u1): add_pending_action (2): 'autoactivate'
[devices/nm-device.c:6376] nm_device_remove_pending_action(): (wlp0s4f1u1): remove_pending_action (1): 'autoactivate'
[nm-manager.c:718] check_if_startup_complete(): check_if_startup_complete returns FALSE because of wlp0s4f1u1
[supplicant-manager/nm-supplicant-interface.c:856] interface_add_cb(): (wlp0s4f1u1): error adding interface: wpa_supplicant couldn't grab this interface.
(wlp0s4f1u1): supplicant interface state: starting -> down
[devices/nm-device.c:6376] nm_device_remove_pending_action(): (wlp0s4f1u1): remove_pending_action (0): 'waiting for supplicant'
[supplicant-manager/nm-supplicant-manager.c:90] nm_supplicant_manager_iface_get(): (wlp0s4f1u1): creating new supplicant interface
[supplicant-manager/nm-supplicant-interface.c:881] interface_add(): (wlp0s4f1u1): adding interface to supplicant
[devices/nm-device.c:6342] nm_device_add_pending_action(): (wlp0s4f1u1): add_pending_action (1): 'waiting for supplicant'
[supplicant-manager/nm-supplicant-manager.c:182] get_capabilities_cb(): AP mode is supported
[supplicant-manager/nm-supplicant-manager.c:194] get_capabilities_cb(): EAP-FAST is supported
[supplicant-manager/nm-supplicant-interface.c:856] interface_add_cb(): (wlp0s4f1u1): error adding interface: wpa_supplicant couldn't grab this interface.
etc. etc.. etc...
- nmcli device
DEVICE TYPE STATE CONNECTION
wlp0s4f1u1 wifi unavailable --
poma
next reply other threads:[~2014-09-29 9:29 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-09-29 9:29 poma [this message]
2014-09-29 19:46 ` RTL8188SU(rtl8192su) - unavailable Dan Williams
2014-10-02 3:45 ` poma
[not found] ` <CAAd0S9ARKg4RSQ_CYrEu8ggm3mWqL8a3ODgJDMnaKbHXpMZPCA@mail.gmail.com>
2014-10-02 15:04 ` poma
2014-10-06 20:33 ` poma
2014-10-14 0:59 ` RTL8188SU(rtl8192su) & rtl8192sufw-ap.bin poma
2014-10-14 20:22 ` Dan Williams
2014-10-15 2:20 ` poma
2014-10-17 17:26 ` poma
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=54292675.4090607@gmail.com \
--to=pomidorabelisima@gmail.com \
--cc=Joshua.Roys@gtri.gatech.edu \
--cc=Larry.Finger@lwfinger.net \
--cc=chaoming_li@realsil.com.cn \
--cc=chunkeey@googlemail.com \
--cc=linux-wireless@vger.kernel.org \
--cc=networkmanager-list@gnome.org \
--cc=wlanfae@realtek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.