From: poma <pomidorabelisima@gmail.com>
To: Christian Lamparter <chunkeey@googlemail.com>
Cc: Joshua Roys <Joshua.Roys@gtri.gatech.edu>,
Dan Williams <dcbw@redhat.com>,
Network Manager <networkmanager-list@gnome.org>,
Larry Finger <Larry.Finger@lwfinger.net>,
lizhaoming <chaoming_li@realsil.com.cn>,
Realtek WlanFAE <wlanfae@realtek.com>,
linux-wireless@vger.kernel.org
Subject: Re: RTL8188SU(rtl8192su) & rtl8192sufw-ap.bin
Date: Tue, 14 Oct 2014 02:59:31 +0200 [thread overview]
Message-ID: <543C7573.30701@gmail.com> (raw)
In-Reply-To: <5432FCB6.5010900@gmail.com>
Realtek RTL8188SU/RTL8191SU/RTL8192SU driver
https://github.com/chunkeey/rtl8192su
&
RTL8188SU
~~~~~~~
- lsusb
Bus 002 Device 003: ID 0bda:8171 Realtek Semiconductor Corp. RTL8188SU 802.11n WLAN Adapter
~~~~~~~~~~
- lsusb -t
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/6p, 480M
...
|__ Port 3: Dev 3, If 0, Class=Vendor Specific Class, Driver=rtl8192su, 480M
~~~~~~~~~~~~~~~~~~~~~~~
- ethtool -i wlp0s4f1u3
driver: rtl8192su
...
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
- /usr/lib/firmware/rtlwifi/rtl8192sufw.bin
eq
https://github.com/chunkeey/rtl8192su/raw/master/firmwares/rtl8192sufw-ap.bin
~~~~~~~~~~~~~~~~~~~~~
- iwconfig wlp0s4f1u3
wlp0s4f1u3 IEEE 802.11bgn Mode:Master Tx-Power=20 dBm
Retry short limit:7 RTS thr=2347 B Fragment thr:off
Power Management:off
~~~~~~~~~~~~~~~~~~~~~
- ifconfig wlp0s4f1u3
wlp0s4f1u3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.42.0.1 netmask 255.255.255.0 broadcast 10.42.0.255
inet6 fe80::201:2ff:fe03:405 prefixlen 64 scopeid 0x20<link>
ether 00:01:02:03:04:05 txqueuelen 1000 (Ethernet)
RX packets 77 bytes 7421 (7.2 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 126 bytes 27469 (26.8 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
~~~~~~~~~~~~~~~~~~~~
- iw wlp0s4f1u3 info
Interface wlp0s4f1u3
ifindex 5
wdev 0x100000001
addr 00:01:02:03:04:05
ssid RTL8188SU(rtl8192su)
type AP
wiphy 1
channel 1 (2412 MHz), width: 20 MHz, center1: 2412 MHz
~~~~~~~~~
- iw list
Wiphy phy1
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
RTS threshold: 2347
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP (00-0f-ac:4)
* CMAC (00-0f-ac:6)
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
Band 1:
Capabilities: 0x1862
HT20/HT40
Static SM Power Save
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 16 usec (0x07)
HT TX/RX MCS rate indexes supported: 0-7, 32
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps
* 5.5 Mbps
* 11.0 Mbps
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm)
* 2472 MHz [13] (20.0 dBm)
* 2484 MHz [14] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* Unknown command (104)
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
software interface modes (can always be added):
* AP/VLAN
* monitor
interface combinations are not supported
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports low priority scan.
Device supports scan flush.
Device supports AP scan.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~
- iw wlp0s4f1u3 station dump
Station 00:22:44:66:88:aa (on wlp0s4f1u3)
inactive time: 15052 ms
rx bytes: 36692
rx packets: 349
tx bytes: 67232
tx packets: 282
tx retries: 0
tx failed: 0
signal: -30 dBm
signal avg: -30 dBm
tx bitrate: 72.2 MBit/s MCS 7 short GI
rx bitrate: 6.0 MBit/s
authorized: yes
authenticated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
- /etc/NetworkManager/system-connections/AP
[connection]
id=AP
uuid=12345678-1234-5678-9abc-123456789abc
type=wifi
autoconnect=true
[wifi]
ssid=RTL8188SU(rtl8192su)
mode=ap
mac-address=00:01:02:03:04:05
security=802-11-wireless-security
[wifi-security]
key-mgmt=wpa-psk
proto=rsn
pairwise=ccmp
psk=passphrase
[ipv4]
method=shared
[ipv6]
method=ignore
~~~~~~~~~~~~~~~~~~~~~~~~~~~
- journalctl NetworkManager
[ 25.277724] systemd[1]: Starting Network Manager...
[ 25.616088] NM[820]: <info> NetworkManager (version 0.9.10.0-5.git20140704.fc21) is starting...
[ 25.616296] NM[820]: <info> Read config: /etc/NetworkManager/NetworkManager.conf and conf.d: keyfile-plugin.conf
[ 25.616468] NM[820]: <info> WEXT support is enabled
[ 26.111881] NM[820]: <info> Loaded plugin keyfile: (c) 2007 - 2013 Red Hat, Inc. To report bugs please use the NetworkManager mailing list.
[ 26.137541] NM[820]: <info> new connection /etc/NetworkManager/system-connections/enp3s0
[ 26.271517] NM[820]: <info> new connection /etc/NetworkManager/system-connections/AP
[ 26.281099] NM[820]: <info> new connection /etc/NetworkManager/system-connections/MBB
[ 26.296694] NM[820]: <info> monitoring kernel firmware directory '/lib/firmware'.
[ 26.298418] NM[820]: <info> rfkill0: found WiFi radio killswitch (at /sys/devices/pci0000:00/0000:00:04.1/usb2/2-3/2-3:1.0/ieee80211/phy0/rfkill0) (driver rtl8192su)
[ 26.298898] NM[820]: <info> WiFi hardware radio set enabled
[ 26.299359] NM[820]: <info> WWAN hardware radio set enabled
[ 26.301854] NM[820]: <info> Loaded device plugin: /usr/lib64/NetworkManager/libnm-device-plugin-wwan.so
[ 26.302361] NM[820]: <info> Loaded device plugin: /usr/lib64/NetworkManager/libnm-device-plugin-wifi.so
[ 26.302818] NM[820]: <info> WiFi enabled by radio killswitch; enabled by state file
[ 26.303284] NM[820]: <info> WWAN enabled by radio killswitch; enabled by state file
[ 26.303754] NM[820]: <info> WiMAX enabled by radio killswitch; enabled by state file
[ 26.304255] NM[820]: <info> Networking is enabled by state file
[ 26.304632] systemd[1]: Started Network Manager.
[ 26.313508] NM[820]: <info> (lo): link connected
[ 26.313671] NM[820]: <info> (lo): carrier is ON
[ 26.313817] NM[820]: <info> (lo): new Generic device (driver: 'unknown' ifindex: 1)
[ 26.313967] NM[820]: <info> (lo): exported as /org/freedesktop/NetworkManager/Devices/0
[ 26.347836] NM[820]: <info> (enp3s0): carrier is OFF
[ 26.365975] NM[820]: <info> (enp3s0): new Ethernet device (driver: 'r8169' ifindex: 3)
[ 26.366704] NM[820]: <info> (enp3s0): exported as /org/freedesktop/NetworkManager/Devices/1
[ 26.367298] NM[820]: <info> (enp3s0): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2]
[ 26.389929] NM[820]: <info> (enp3s0): preparing device
[ 26.391212] NM[820]: <info> (wlp0s4f1u3): using nl80211 for WiFi device control
[ 26.391720] NM[820]: <info> (wlp0s4f1u3): driver supports Access Point (AP) mode
[ 26.392201] NM[820]: <info> (wlp0s4f1u3): new 802.11 WiFi device (driver: 'rtl8192su' ifindex: 4)
[ 26.392649] NM[820]: <info> (wlp0s4f1u3): exported as /org/freedesktop/NetworkManager/Devices/2
[ 26.393123] NM[820]: <info> (wlp0s4f1u3): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2]
[ 27.348116] NM[820]: <info> (wlp0s4f1u3): preparing device
[ 27.357681] NM[820]: <info> ModemManager available in the bus
[ 28.033860] NM[820]: <info> (enp3s0): link connected
[ 28.035054] NM[820]: <info> (enp3s0): device state change: unavailable -> disconnected (reason 'carrier-changed') [20 30 40]
[ 28.035713] NM[820]: <info> Auto-activating connection 'enp3s0'.
[ 28.040332] NM[820]: <info> Activation (enp3s0) starting connection 'enp3s0'
[ 28.040846] NM[820]: <info> Activation (enp3s0) Stage 1 of 5 (Device Prepare) scheduled...
[ 28.041318] NM[820]: <info> Activation (enp3s0) Stage 1 of 5 (Device Prepare) started...
[ 28.041776] NM[820]: <info> (enp3s0): device state change: disconnected -> prepare (reason 'none') [30 40 0]
[ 28.042246] NM[820]: <info> NetworkManager state is now CONNECTING
[ 28.042698] NM[820]: <info> Activation (enp3s0) Stage 2 of 5 (Device Configure) scheduled...
[ 28.043182] NM[820]: <info> Activation (enp3s0) Stage 1 of 5 (Device Prepare) complete.
[ 28.043634] NM[820]: <info> Activation (enp3s0) Stage 2 of 5 (Device Configure) starting...
[ 28.044072] NM[820]: <info> (enp3s0): device state change: prepare -> config (reason 'none') [40 50 0]
[ 28.061851] NM[820]: <info> Activation (enp3s0) Stage 2 of 5 (Device Configure) successful.
[ 28.062348] NM[820]: <info> Activation (enp3s0) Stage 2 of 5 (Device Configure) complete.
[ 28.325821] NM[820]: <info> wpa_supplicant started
[ 28.466946] NM[820]: <info> (wlp0s4f1u3) supports 4 scan SSIDs
[ 28.467471] NM[820]: <info> (wlp0s4f1u3): supplicant interface state: starting -> ready
[ 28.467930] NM[820]: <info> (wlp0s4f1u3): device state change: unavailable -> disconnected (reason 'supplicant-available') [20 30 42]
[ 28.468893] NM[820]: <info> (wlp0s4f1u3): supplicant interface state: ready -> disconnected
[ 28.469370] NM[820]: <info> (wlp0s4f1u3) supports 4 scan SSIDs
[ 28.469837] NM[820]: <info> Auto-activating connection 'AP'.
[ 28.475692] NM[820]: <info> Activation (wlp0s4f1u3) starting connection 'AP'
[ 28.476128] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) scheduled...
[ 28.476311] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) started...
[ 28.476491] NM[820]: <info> (wlp0s4f1u3): device state change: disconnected -> prepare (reason 'none') [30 40 0]
[ 28.476672] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) scheduled...
[ 28.476852] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) complete.
[ 28.477047] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) starting...
[ 28.477225] NM[820]: <info> (wlp0s4f1u3): device state change: prepare -> config (reason 'none') [40 50 0]
[ 28.477400] NM[820]: <info> Activation (wlp0s4f1u3/wireless): connection 'AP' has security, and secrets exist. No new secrets needed.
[ 28.477574] NM[820]: <info> Config: added 'ssid' value 'RTL8188SU(rtl8192su)'
[ 28.477750] NM[820]: <info> Config: added 'mode' value '2'
[ 28.477925] NM[820]: <info> Config: added 'frequency' value '2412'
[ 28.478111] NM[820]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
[ 28.478286] NM[820]: <info> Config: added 'psk' value '<omitted>'
[ 28.478459] NM[820]: <info> Config: added 'proto' value 'RSN'
[ 28.478632] NM[820]: <info> Config: added 'pairwise' value 'CCMP'
[ 28.478809] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) complete.
[ 28.478982] NM[820]: <info> Config: set interface ap_scan to 2
[ 28.738684] NM[820]: <info> (wlp0s4f1u3): supplicant interface state: disconnected -> completed
[ 28.738891] NM[820]: <info> Activation (wlp0s4f1u3/wireless) Stage 2 of 5 (Device Configure) successful. Started Wi-Fi Hotspot 'RTL8188SU(rtl8192su)'.
[ 34.977083] NM[820]: <info> Activation (enp3s0) Stage 3 of 5 (IP Configure Start) scheduled.
[ 34.977610] NM[820]: <info> Activation (enp3s0) Stage 3 of 5 (IP Configure Start) started...
[ 34.978096] NM[820]: <info> (enp3s0): device state change: config -> ip-config (reason 'none') [50 70 0]
[ 34.978554] NM[820]: <info> Activation (enp3s0) Beginning DHCPv4 transaction (timeout in 45 seconds)
[ 35.304547] NM[820]: <info> dhclient started with pid 1395
[ 35.305087] NM[820]: <info> Activation (enp3s0) Stage 3 of 5 (IP Configure Start) complete.
[ 35.306502] NM[820]: <info> Activation (wlp0s4f1u3) Stage 3 of 5 (IP Configure Start) scheduled.
[ 35.306985] NM[820]: <info> Activation (wlp0s4f1u3) Stage 3 of 5 (IP Configure Start) started...
[ 35.307480] NM[820]: <info> (wlp0s4f1u3): device state change: config -> ip-config (reason 'none') [50 70 0]
[ 35.307976] NM[820]: <info> Activation (wlp0s4f1u3) Stage 5 of 5 (IPv4 Configure Commit) scheduled...
[ 35.308447] NM[820]: <info> Activation (wlp0s4f1u3) Stage 3 of 5 (IP Configure Start) complete.
[ 35.308937] NM[820]: <info> Activation (wlp0s4f1u3) Stage 5 of 5 (IPv4 Commit) started...
[ 35.490657] dhclient[1395]: Internet Systems Consortium DHCP Client 4.3.1
[ 35.491211] dhclient[1395]: Copyright 2004-2014 Internet Systems Consortium.
[ 35.491674] dhclient[1395]: All rights reserved.
[ 35.492147] dhclient[1395]: For info, please visit https://www.isc.org/software/dhcp/
[ 35.492592] dhclient[1395]:
[ 35.493078] NM[820]: Internet Systems Consortium DHCP Client 4.3.1
[ 35.493519] NM[820]: Copyright 2004-2014 Internet Systems Consortium.
[ 35.493950] NM[820]: All rights reserved.
[ 35.494211] NM[820]: For info, please visit https://www.isc.org/software/dhcp/
[ 36.725988] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert INPUT --in-interface wlp0s4f1u3 --protocol tcp --destination-port 53 --jump ACCEPT
[ 36.733764] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert INPUT --in-interface wlp0s4f1u3 --protocol udp --destination-port 53 --jump ACCEPT
[ 36.752064] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert INPUT --in-interface wlp0s4f1u3 --protocol tcp --destination-port 67 --jump ACCEPT
[ 36.757195] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert INPUT --in-interface wlp0s4f1u3 --protocol udp --destination-port 67 --jump ACCEPT
[ 36.776083] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --in-interface wlp0s4f1u3 --jump REJECT
[ 36.781590] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --out-interface wlp0s4f1u3 --jump REJECT
[ 36.786875] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --in-interface wlp0s4f1u3 --out-interface wlp0s4f1u3 --jump ACCEPT
[ 36.789805] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --source 10.42.0.0/255.255.255.0 --in-interface wlp0s4f1u3 --jump ACCEPT
[ 36.792748] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --destination 10.42.0.0/255.255.255.0 --out-interface wlp0s4f1u3 --match state --state ESTABLISHED,RELATED --jump ACCEPT
[ 38.812843] NM[820]: <info> Executing: /usr/sbin/iptables --table nat --insert POSTROUTING --source 10.42.0.0/255.255.255.0 ! --destination 10.42.0.0/255.255.255.0 --jump MASQUERADE
[ 38.816972] NM[820]: <info> Starting dnsmasq...
[ 38.818556] NM[820]: <info> (wlp0s4f1u3): device state change: ip-config -> ip-check (reason 'none') [70 80 0]
[ 38.818941] NM[820]: <info> Activation (wlp0s4f1u3) Stage 5 of 5 (IPv4 Commit) complete.
[ 38.822707] NM[820]: <info> (enp3s0): DHCPv4 state changed nbi -> preinit
[ 38.825233] NM[820]: <info> (wlp0s4f1u3): device state change: ip-check -> secondaries (reason 'none') [80 90 0]
[ 38.826026] NM[820]: <info> (wlp0s4f1u3): device state change: secondaries -> activated (reason 'none') [90 100 0]
[ 38.881776] dhclient[1395]: Listening on LPF/enp3s0/00:12:34:56:78:30
[ 38.882317] dhclient[1395]: Sending on LPF/enp3s0/00:12:34:56:78:30
[ 38.882777] dhclient[1395]: Sending on Socket/fallback
[ 38.883995] dhclient[1395]: DHCPREQUEST on enp3s0 to 255.255.255.255 port 67 (xid=0x9c4e1f)
[ 38.884524] dhclient[1395]: DHCPACK from 192.168.2.1 (xid=0x9c4e1f)
[ 38.885027] NM[820]: Listening on LPF/enp3s0/00:12:34:56:78:30
[ 38.885471] NM[820]: Sending on LPF/enp3s0/00:12:34:56:78:30
[ 38.885903] NM[820]: Sending on Socket/fallback
[ 38.886356] NM[820]: DHCPREQUEST on enp3s0 to 255.255.255.255 port 67 (xid=0x9c4e1f)
[ 38.886787] NM[820]: DHCPACK from 192.168.2.1 (xid=0x9c4e1f)
[ 39.008666] dnsmasq[1416]: started, version 2.72 cachesize 150
[ 39.009255] dnsmasq[1416]: compile time options: IPv6 GNU-getopt DBus no-i18n IDN DHCP DHCPv6 no-Lua TFTP no-conntrack ipset auth DNSSEC loop-detect
[ 39.009719] dnsmasq-dhcp[1416]: DHCP, IP range 10.42.0.10 -- 10.42.0.254, lease time 1h
[ 39.010186] dnsmasq[1416]: reading /etc/resolv.conf
[ 39.010634] dnsmasq[1416]: using nameserver 192.168.2.1#53
[ 39.012048] dnsmasq[1416]: cleared cache
[ 44.464210] NM[820]: <info> Activation (wlp0s4f1u3) successful, device activated.
[ 44.470643] NM[820]: <info> (enp3s0): DHCPv4 state changed preinit -> reboot
[ 44.472389] NM[820]: <info> address 192.168.2.35
[ 44.472910] NM[820]: <info> plen 24 (255.255.255.0)
[ 44.473421] NM[820]: <info> gateway 192.168.2.1
[ 44.473892] NM[820]: <info> server identifier 192.168.2.1
[ 44.474382] NM[820]: <info> lease time 600
[ 44.474841] NM[820]: <info> nameserver '192.168.2.1'
[ 44.476312] NM[820]: <info> Activation (enp3s0) Stage 5 of 5 (IPv4 Configure Commit) scheduled...
[ 44.476428] NM[820]: <info> Activation (enp3s0) Stage 5 of 5 (IPv4 Commit) started...
[ 44.476548] NM[820]: <info> (enp3s0): device state change: ip-config -> ip-check (reason 'none') [70 80 0]
[ 44.476664] NM[820]: <info> Activation (enp3s0) Stage 5 of 5 (IPv4 Commit) complete.
[ 44.476782] NM[820]: <info> (enp3s0): device state change: ip-check -> secondaries (reason 'none') [80 90 0]
[ 44.476897] NM[820]: <info> (enp3s0): device state change: secondaries -> activated (reason 'none') [90 100 0]
[ 44.477060] NM[820]: <info> NetworkManager state is now CONNECTED_LOCAL
[ 44.671564] dhclient[1395]: bound to 192.168.2.35 -- renewal in 253 seconds.
[ 44.672104] NM[820]: bound to 192.168.2.35 -- renewal in 253 seconds.
[ 44.672581] NM[820]: <info> NetworkManager state is now CONNECTED_GLOBAL
[ 44.673074] NM[820]: <info> Policy set 'enp3s0' (enp3s0) as default for IPv4 routing and DNS.
[ 44.719277] NM[820]: <info> Activation (enp3s0) successful, device activated.
[ 44.721265] NM[820]: <info> startup complete
[ 95.712977] dnsmasq[1416]: reading /etc/resolv.conf
[ 95.713657] dnsmasq[1416]: using nameserver 192.168.2.1#53
[ 95.715255] dnsmasq[1416]: cleared cache
[ 217.044170] dnsmasq-dhcp[1416]: DHCPREQUEST(wlp0s4f1u3) 10.42.0.77 00:22:44:66:88:aa
[ 217.044896] dnsmasq-dhcp[1416]: DHCPACK(wlp0s4f1u3) 10.42.0.77 00:22:44:66:88:aa android-0123456789abcdef
...
[ 1240.752553] dnsmasq-dhcp[1416]: DHCPREQUEST(wlp0s4f1u3) 10.42.0.77 00:22:44:66:88:aa
[ 1240.813416] dnsmasq-dhcp[1416]: DHCPACK(wlp0s4f1u3) 10.42.0.77 00:22:44:66:88:aa android-0123456789abcdef
...
[ 1408.894826] dnsmasq-dhcp[1416]: DHCPREQUEST(wlp0s4f1u3) 10.42.0.77 00:22:44:66:88:aa
[ 1408.895557] dnsmasq-dhcp[1416]: DHCPACK(wlp0s4f1u3) 10.42.0.77 00:22:44:66:88:aa android-0123456789abcdef
- systemctl suspend
& resume(S3)
[ 1689.325793] NM[820]: <info> (wlp0s4f1u3): device state change: activated -> unmanaged (reason 'removed') [100 10 36]
[ 1689.325961] NM[820]: <info> (wlp0s4f1u3): deactivating device (reason 'removed') [36]
[ 1689.326448] NM[820]: <info> radio killswitch /sys/devices/pci0000:00/0000:00:04.1/usb2/2-3/2-3:1.0/ieee80211/phy0/rfkill0 disappeared
[ 1689.326580] NM[820]: <info> (wlp0s4f1u3): using nl80211 for WiFi device control
[ 1689.326709] NM[820]: <info> (wlp0s4f1u3): driver supports Access Point (AP) mode
[ 1689.326834] NM[820]: <info> (wlp0s4f1u3): new 802.11 WiFi device (driver: 'rtl8192su' ifindex: 5)
[ 1689.326966] NM[820]: <info> (wlp0s4f1u3): exported as /org/freedesktop/NetworkManager/Devices/3
[ 1689.327098] NM[820]: <info> (wlp0s4f1u3): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2]
[ 1689.327223] NM[820]: <info> (wlp0s4f1u3): preparing device
[ 1689.328176] NM[820]: <info> rfkill1: found WiFi radio killswitch (at /sys/devices/pci0000:00/0000:00:04.1/usb2/2-3/2-3:1.0/ieee80211/phy1/rfkill1) (driver rtl8192su)
[ 1689.329155] NM[820]: <info> Executing: /usr/sbin/iptables --table nat --delete POSTROUTING --source 10.42.0.0/255.255.255.0 ! --destination 10.42.0.0/255.255.255.0 --jump MASQUERADE
[ 1689.331088] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete FORWARD --destination 10.42.0.0/255.255.255.0 --out-interface wlp0s4f1u3 --match state --state ESTABLISHED,RELATED --jump ACCEPT
[ 1689.334823] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete FORWARD --source 10.42.0.0/255.255.255.0 --in-interface wlp0s4f1u3 --jump ACCEPT
[ 1689.336627] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete FORWARD --in-interface wlp0s4f1u3 --out-interface wlp0s4f1u3 --jump ACCEPT
[ 1689.338561] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete FORWARD --out-interface wlp0s4f1u3 --jump REJECT
[ 1689.341038] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete FORWARD --in-interface wlp0s4f1u3 --jump REJECT
[ 1689.343125] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete INPUT --in-interface wlp0s4f1u3 --protocol udp --destination-port 67 --jump ACCEPT
[ 1689.380119] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete INPUT --in-interface wlp0s4f1u3 --protocol tcp --destination-port 67 --jump ACCEPT
[ 1689.385774] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete INPUT --in-interface wlp0s4f1u3 --protocol udp --destination-port 53 --jump ACCEPT
[ 1690.325415] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --delete INPUT --in-interface wlp0s4f1u3 --protocol tcp --destination-port 53 --jump ACCEPT
[ 1690.336827] NM[820]: <info> (wlp0s4f1u3) supports 4 scan SSIDs
[ 1690.337091] NM[820]: <info> (wlp0s4f1u3): supplicant interface state: starting -> ready
[ 1690.337297] NM[820]: <info> (wlp0s4f1u3): device state change: unavailable -> disconnected (reason 'supplicant-available') [20 30 42]
[ 1690.337493] NM[820]: <info> (wlp0s4f1u3): supplicant interface state: ready -> disconnected
[ 1690.337686] NM[820]: <info> (wlp0s4f1u3) supports 4 scan SSIDs
[ 1690.337884] NM[820]: <info> Auto-activating connection 'AP'.
[ 1690.338085] NM[820]: <info> Activation (wlp0s4f1u3) starting connection 'AP'
[ 1690.338281] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) scheduled...
[ 1690.338472] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) started...
[ 1690.338672] NM[820]: <info> (wlp0s4f1u3): device state change: disconnected -> prepare (reason 'none') [30 40 0]
[ 1690.338865] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) scheduled...
[ 1690.339062] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) complete.
[ 1690.339257] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) starting...
[ 1690.339452] NM[820]: <info> (wlp0s4f1u3): device state change: prepare -> config (reason 'none') [40 50 0]
[ 1690.343841] NM[820]: <info> Activation (wlp0s4f1u3/wireless): access point 'AP' has security, but secrets are required.
[ 1690.344110] NM[820]: <info> (wlp0s4f1u3): device state change: config -> need-auth (reason 'none') [50 60 0]
[ 1690.344304] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) complete.
[ 1690.344436] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) scheduled...
[ 1690.348812] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) started...
[ 1690.348980] NM[820]: <info> (wlp0s4f1u3): device state change: need-auth -> prepare (reason 'none') [60 40 0]
[ 1690.349130] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) scheduled...
[ 1690.349260] NM[820]: <info> Activation (wlp0s4f1u3) Stage 1 of 5 (Device Prepare) complete.
[ 1690.349389] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) starting...
[ 1690.349519] NM[820]: <info> (wlp0s4f1u3): device state change: prepare -> config (reason 'none') [40 50 0]
[ 1690.349653] NM[820]: <info> Activation (wlp0s4f1u3/wireless): connection 'AP' has security, and secrets exist. No new secrets needed.
[ 1690.349783] NM[820]: <info> Config: added 'ssid' value 'RTL8188SU(rtl8192su)'
[ 1690.349911] NM[820]: <info> Config: added 'mode' value '2'
[ 1690.350052] NM[820]: <info> Config: added 'frequency' value '2412'
[ 1690.350186] NM[820]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
[ 1690.350311] NM[820]: <info> Config: added 'psk' value '<omitted>'
[ 1690.350440] NM[820]: <info> Config: added 'proto' value 'RSN'
[ 1690.350567] NM[820]: <info> Config: added 'pairwise' value 'CCMP'
[ 1690.350692] NM[820]: <info> Activation (wlp0s4f1u3) Stage 2 of 5 (Device Configure) complete.
[ 1690.355138] NM[820]: <info> Config: set interface ap_scan to 2
[ 1690.439942] NM[820]: <info> (wlp0s4f1u3): supplicant interface state: disconnected -> completed
[ 1690.440552] NM[820]: <info> Activation (wlp0s4f1u3/wireless) Stage 2 of 5 (Device Configure) successful. Started Wi-Fi Hotspot 'RTL8188SU(rtl8192su)'.
[ 1690.496432] NM[820]: <info> Activation (wlp0s4f1u3) Stage 3 of 5 (IP Configure Start) scheduled.
[ 1690.497084] NM[820]: <info> Activation (wlp0s4f1u3) Stage 3 of 5 (IP Configure Start) started...
[ 1690.497617] NM[820]: <info> (wlp0s4f1u3): device state change: config -> ip-config (reason 'none') [50 70 0]
[ 1690.498145] NM[820]: <info> Activation (wlp0s4f1u3) Stage 5 of 5 (IPv4 Configure Commit) scheduled...
[ 1690.498669] NM[820]: <info> Activation (wlp0s4f1u3) Stage 3 of 5 (IP Configure Start) complete.
[ 1690.499196] NM[820]: <info> Activation (wlp0s4f1u3) Stage 5 of 5 (IPv4 Commit) started...
[ 1690.519773] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert INPUT --in-interface wlp0s4f1u3 --protocol tcp --destination-port 53 --jump ACCEPT
[ 1690.522189] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert INPUT --in-interface wlp0s4f1u3 --protocol udp --destination-port 53 --jump ACCEPT
[ 1690.550111] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert INPUT --in-interface wlp0s4f1u3 --protocol tcp --destination-port 67 --jump ACCEPT
[ 1690.555813] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert INPUT --in-interface wlp0s4f1u3 --protocol udp --destination-port 67 --jump ACCEPT
[ 1690.573980] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --in-interface wlp0s4f1u3 --jump REJECT
[ 1690.577369] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --out-interface wlp0s4f1u3 --jump REJECT
[ 1690.580764] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --in-interface wlp0s4f1u3 --out-interface wlp0s4f1u3 --jump ACCEPT
[ 1690.585441] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --source 10.42.0.0/255.255.255.0 --in-interface wlp0s4f1u3 --jump ACCEPT
[ 1690.587979] NM[820]: <info> Executing: /usr/sbin/iptables --table filter --insert FORWARD --destination 10.42.0.0/255.255.255.0 --out-interface wlp0s4f1u3 --match state --state ESTABLISHED,RELATED --jump ACCEPT
[ 1690.590492] NM[820]: <info> Executing: /usr/sbin/iptables --table nat --insert POSTROUTING --source 10.42.0.0/255.255.255.0 ! --destination 10.42.0.0/255.255.255.0 --jump MASQUERADE
[ 1690.592764] NM[820]: <info> Starting dnsmasq...
[ 1690.593692] NM[820]: <info> (wlp0s4f1u3): device state change: ip-config -> ip-check (reason 'none') [70 80 0]
[ 1690.594290] NM[820]: <info> Activation (wlp0s4f1u3) Stage 5 of 5 (IPv4 Commit) complete.
[ 1690.595395] dnsmasq[3442]: started, version 2.72 cachesize 150
[ 1690.595629] dnsmasq[3442]: compile time options: IPv6 GNU-getopt DBus no-i18n IDN DHCP DHCPv6 no-Lua TFTP no-conntrack ipset auth DNSSEC loop-detect
[ 1690.595822] dnsmasq-dhcp[3442]: DHCP, IP range 10.42.0.10 -- 10.42.0.254, lease time 1h
[ 1690.596021] dnsmasq[3442]: reading /etc/resolv.conf
[ 1690.596216] dnsmasq[3442]: using nameserver 192.168.2.1#53
[ 1690.596793] dnsmasq[3442]: cleared cache
[ 1690.596982] NM[820]: <info> (wlp0s4f1u3): device state change: ip-check -> secondaries (reason 'none') [80 90 0]
[ 1690.597182] NM[820]: <info> (wlp0s4f1u3): device state change: secondaries -> activated (reason 'none') [90 100 0]
[ 1691.068838] NM[820]: <info> Activation (wlp0s4f1u3) successful, device activated.
[ 1698.780512] dnsmasq-dhcp[3442]: DHCPREQUEST(wlp0s4f1u3) 10.42.0.77 00:22:44:66:88:aa
[ 1698.781136] dnsmasq-dhcp[3442]: DHCPACK(wlp0s4f1u3) 10.42.0.77 00:22:44:66:88:aa android-0123456789abcdef
~~~~~~~
- dmesg
[ 2.126073] usb 2-3: new high-speed USB device number 3 using ehci-pci
[ 2.242873] usb 2-3: New USB device found, idVendor=0bda, idProduct=8171
[ 2.242880] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.242883] usb 2-3: Product: RTL8188S WLAN Adapter
[ 2.242885] usb 2-3: Manufacturer: Manufacturer Realtek
[ 2.242887] usb 2-3: SerialNumber: 00e04c000001
[ 20.134415] rtlwifi: module verification failed: signature and/or required key missing - tainting kernel
[ 20.517392] rtl8192s_common: Chip version 0x3
[ 20.686391] rtl_usb: rx_max_size 9100, rx_urb_num 8, in_ep 3
[ 20.687057] rtl8192su: Power Save off (module option)
[ 20.687639] rtl8192su: FW Power Save off (module option)
[ 20.688394] rtl8192su: Driver for Realtek RTL8192SU/RTL8191SU
Loading firmware rtlwifi/rtl8192sufw.bin
[ 20.689751] usbcore: registered new interface driver rtl8192su
[ 20.850838] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 20.854551] rtl8192su 2-3:1.0 wlp0s4f1u3: renamed from wlan0
- systemctl suspend
[ 1679.990678] PM: Preparing system for mem sleep
[ 1680.178832] Freezing user space processes ... (elapsed 0.048 seconds) done.
[ 1680.226937] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 1680.228270] PM: Entering mem sleep
[ 1680.228299] Suspending console(s) (use no_console_suspend to debug)
[ 1682.772451] PM: suspend of devices complete after 2543.533 msecs
[ 1682.773864] PM: late suspend of devices complete after 1.407 msecs
[ 1682.775348] ehci-pci 0000:00:02.1: System wakeup enabled by ACPI
[ 1682.786410] PM: noirq suspend of devices complete after 12.536 msecs
[ 1682.787692] ACPI: Preparing to enter system sleep state S3
[ 1682.788861] PM: Saving platform NVS memory
& resume(S3)
[ 1682.798859] ACPI: Low-level resume complete
[ 1682.798924] PM: Restoring platform NVS memory
[ 1682.844566] ACPI: Waking up from system sleep state S3
[ 1682.855147] ehci-pci 0000:00:02.1: System wakeup disabled by ACPI
[ 1682.856186] PM: noirq resume of devices complete after 11.457 msecs
[ 1682.856759] PM: early resume of devices complete after 0.531 msecs
[ 1683.074063] PM: resume of devices complete after 217.286 msecs
[ 1683.074332] rtl8192s_common: Chip version 0x3
[ 1683.218439] rtl_usb: rx_max_size 9100, rx_urb_num 8, in_ep 3
[ 1683.218484] rtl8192su: Power Save off (module option)
[ 1683.218485] rtl8192su: FW Power Save off (module option)
[ 1683.218694] rtl8192su: Driver for Realtek RTL8192SU/RTL8191SU
Loading firmware rtlwifi/rtl8192sufw.bin
[ 1683.219176] ieee80211 phy1: Selected rate control algorithm 'rtl_rc'
[ 1683.234998] PM: Finishing wakeup.
[ 1683.235003] Restarting tasks ... done.
[ 1683.258259] rtl8192su 2-3:1.0 wlp0s4f1u3: renamed from wlan0
[ 1683.270928] IPv6: ADDRCONF(NETDEV_UP): wlp0s4f1u3: link is not ready
[ 1684.238973] IPv6: ADDRCONF(NETDEV_UP): wlp0s4f1u3: link is not ready
[ 1684.401143] r8169 0000:03:00.0 enp3s0: link up
[ 1691.249718] IPv6: ADDRCONF(NETDEV_UP): wlp0s4f1u3: link is not ready
[ 1691.376981] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s4f1u3: link becomes ready
~~~~~~~~~~~~~~~~~~~~
http://goo.gl/3O3Tz4
poma
next prev parent reply other threads:[~2014-10-14 0:59 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-09-29 9:29 RTL8188SU(rtl8192su) - unavailable poma
2014-09-29 19:46 ` Dan Williams
2014-10-02 3:45 ` poma
[not found] ` <CAAd0S9ARKg4RSQ_CYrEu8ggm3mWqL8a3ODgJDMnaKbHXpMZPCA@mail.gmail.com>
2014-10-02 15:04 ` poma
2014-10-06 20:33 ` poma
2014-10-14 0:59 ` poma [this message]
2014-10-14 20:22 ` RTL8188SU(rtl8192su) & rtl8192sufw-ap.bin Dan Williams
2014-10-15 2:20 ` poma
2014-10-17 17:26 ` poma
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=543C7573.30701@gmail.com \
--to=pomidorabelisima@gmail.com \
--cc=Joshua.Roys@gtri.gatech.edu \
--cc=Larry.Finger@lwfinger.net \
--cc=chaoming_li@realsil.com.cn \
--cc=chunkeey@googlemail.com \
--cc=dcbw@redhat.com \
--cc=linux-wireless@vger.kernel.org \
--cc=networkmanager-list@gnome.org \
--cc=wlanfae@realtek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.