From: Mike Looijmans <mike.looijmans@topic.nl>
To: Sebastian Reichel <sre@kernel.org>
Cc: linux-pm@vger.kernel.org, linux-kernel@vger.kernel.org,
dbaryshkov@gmail.com, dwmw2@infradead.org
Subject: Re: [PATCH v4] Add LTC2941/LTC2943 Battery Gauge Driver
Date: Tue, 28 Oct 2014 08:03:31 +0100 [thread overview]
Message-ID: <544F3FC3.3040106@topic.nl> (raw)
In-Reply-To: <20141027163842.GB20765@earth.universe>
On 10/27/2014 05:38 PM, Sebastian Reichel wrote:
> Hi,
>
> On Thu, Oct 23, 2014 at 02:38:38PM +0200, Mike Looijmans wrote:
>> Both the LTC2941 and LTC2943 measure battery capacity.
>> The LTC2943 is compatible with the LTC2941, it adds voltage and
>> temperature monitoring, and uses a slightly different conversion
>> formula for the charge counter.
>>
>> To avoid confusion with e.g. the LTC2945, the driver is called
>> LTC2941 instead of LTC294X.
>>
>> v2: Fix units of measurement: uV, uA and centidegrees.
>> v3: Correctly set configuration register. Allow negative values
>> for the sense resistor.
>> v4: Run checkpatch.pl and fix all errors and warnings.
>>
>> Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
>> ---
>> [...]
>>
>> + np = of_node_get(client->dev.of_node);
>> +
>> + /* r_sense can be negative, when sense+ is connected to the battery
>> + * instead of the sense-. This results in reversed measurements. */
>> + ret = of_property_read_u32(np, "resistor-sense", &r_sense);
>> + if (ret < 0) {
>> + dev_err(&client->dev,
>> + "Could not find resistor-sense in devicetree\n");
>> + goto fail_name;
>> + }
>> + info->r_sense = r_sense;
>> +
>> + ret = of_property_read_u32(np, "prescaler-exponent", &prescaler_exp);
>> + if (ret < 0) {
>> + dev_err(&client->dev,
>> + "PrescalerExponent not in devicetree, assume max\n");
>> + prescaler_exp = LTC2941_MAX_PRESCALER_EXP;
>> + }
>
> The device tree properties are not documented. Please document them
> in a separate patch and Cc devicetree binding maintainers.
>
> Apart from that the properties should be vendor prefixed (e.g.
> "lltc,resistor-sense").
Thanks for your feedback. I will post the requested changes asap.
Met vriendelijke groet / kind regards,
Mike Looijmans
System Expert
TOPIC Embedded Systems
Eindhovenseweg 32-C, NL-5683 KH Best
Postbus 440, NL-5680 AK Best
Telefoon: (+31) (0) 499 33 69 79
Telefax: (+31) (0) 499 33 69 70
E-mail: mike.looijmans@topic.nl
Website: www.topic.nl
Please consider the environment before printing this e-mail
Topic zoekt gedreven (embedded) software specialisten!
http://topic.nl/vacatures/topic-zoekt-software-engineers/
WARNING: multiple messages have this Message-ID (diff)
From: Mike Looijmans <mike.looijmans@topic.nl>
To: Sebastian Reichel <sre@kernel.org>
Cc: <linux-pm@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<dbaryshkov@gmail.com>, <dwmw2@infradead.org>
Subject: Re: [PATCH v4] Add LTC2941/LTC2943 Battery Gauge Driver
Date: Tue, 28 Oct 2014 08:03:31 +0100 [thread overview]
Message-ID: <544F3FC3.3040106@topic.nl> (raw)
In-Reply-To: <20141027163842.GB20765@earth.universe>
On 10/27/2014 05:38 PM, Sebastian Reichel wrote:
> Hi,
>
> On Thu, Oct 23, 2014 at 02:38:38PM +0200, Mike Looijmans wrote:
>> Both the LTC2941 and LTC2943 measure battery capacity.
>> The LTC2943 is compatible with the LTC2941, it adds voltage and
>> temperature monitoring, and uses a slightly different conversion
>> formula for the charge counter.
>>
>> To avoid confusion with e.g. the LTC2945, the driver is called
>> LTC2941 instead of LTC294X.
>>
>> v2: Fix units of measurement: uV, uA and centidegrees.
>> v3: Correctly set configuration register. Allow negative values
>> for the sense resistor.
>> v4: Run checkpatch.pl and fix all errors and warnings.
>>
>> Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
>> ---
>> [...]
>>
>> + np = of_node_get(client->dev.of_node);
>> +
>> + /* r_sense can be negative, when sense+ is connected to the battery
>> + * instead of the sense-. This results in reversed measurements. */
>> + ret = of_property_read_u32(np, "resistor-sense", &r_sense);
>> + if (ret < 0) {
>> + dev_err(&client->dev,
>> + "Could not find resistor-sense in devicetree\n");
>> + goto fail_name;
>> + }
>> + info->r_sense = r_sense;
>> +
>> + ret = of_property_read_u32(np, "prescaler-exponent", &prescaler_exp);
>> + if (ret < 0) {
>> + dev_err(&client->dev,
>> + "PrescalerExponent not in devicetree, assume max\n");
>> + prescaler_exp = LTC2941_MAX_PRESCALER_EXP;
>> + }
>
> The device tree properties are not documented. Please document them
> in a separate patch and Cc devicetree binding maintainers.
>
> Apart from that the properties should be vendor prefixed (e.g.
> "lltc,resistor-sense").
Thanks for your feedback. I will post the requested changes asap.
Met vriendelijke groet / kind regards,
Mike Looijmans
System Expert
TOPIC Embedded Systems
Eindhovenseweg 32-C, NL-5683 KH Best
Postbus 440, NL-5680 AK Best
Telefoon: (+31) (0) 499 33 69 79
Telefax: (+31) (0) 499 33 69 70
E-mail: mike.looijmans@topic.nl
Website: www.topic.nl
Please consider the environment before printing this e-mail
Topic zoekt gedreven (embedded) software specialisten!
http://topic.nl/vacatures/topic-zoekt-software-engineers/
next prev parent reply other threads:[~2014-10-28 7:03 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-10-01 13:32 [PATCH v2] Added LTC2941/LTC2943 Battery Gauge Driver Mike Looijmans
2014-10-08 6:05 ` [PATCH v3] Add " Mike Looijmans
2014-10-23 12:38 ` [PATCH v4] " Mike Looijmans
2014-10-27 4:14 ` Pavel Machek
2014-10-27 16:38 ` Sebastian Reichel
2014-10-28 7:03 ` Mike Looijmans [this message]
2014-10-28 7:03 ` Mike Looijmans
2014-10-28 7:05 ` [PATCH] " Mike Looijmans
2015-01-22 2:24 ` Sebastian Reichel
2015-02-11 11:21 ` Mike Looijmans
2015-02-11 11:21 ` Mike Looijmans
2015-02-11 17:01 ` Sebastian Reichel
2014-10-28 7:08 ` [PATCH] Add devicetree binding documentation for the LTC2941/LTC2943 driver Mike Looijmans
[not found] ` <1414480084-3604-1-git-send-email-mike.looijmans-Oq418RWZeHk@public.gmane.org>
2015-01-22 2:24 ` Sebastian Reichel
2015-01-22 2:24 ` Sebastian Reichel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=544F3FC3.3040106@topic.nl \
--to=mike.looijmans@topic.nl \
--cc=dbaryshkov@gmail.com \
--cc=dwmw2@infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=sre@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.