* [meta-raspberrypi] Image will halt soon after boot
@ 2014-12-18 7:22 Petter Gustad
2014-12-18 9:12 ` Maciej Borzecki
2014-12-18 9:54 ` ChenQi
0 siblings, 2 replies; 7+ messages in thread
From: Petter Gustad @ 2014-12-18 7:22 UTC (permalink / raw)
To: yocto@yoctoproject.org
I've run "bitbake rpi-hwup-image" using the daisy branch:
meta-yocto-bsp = "daisy:1e668ccf1a05c5d730de9747bc1c2b0446bda556"
meta-raspberrypi.git = "daisy:946b69299737cc2f1378c864f1b9075280db1b53"
However, whenever I boot the created sdimage it will lock up during
boot. Typically I will see some garbage on the serial console.
Sometimes I'm able to log in, but then then I get no response (as in
the below session). Putting a pre-compiled distribution on the same
sdcard will boot just fine.
Does anybody else observe this behavior?
Is there a specific meta-raspberrypi mailing list?
Best regards
//Petter
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.12.21 (yocto@pangea) (gcc version 4.8.2 (GCC) ) #1 PREEMPT Wed Dec 17 22:58:01 CET 2014
[ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: BCM2708
[ 0.000000] cma: CMA: reserved 8 MiB at 0b800000
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 49152
[ 0.000000] free_area_init_node: node 0, pgdat c061ada0, node_mem_map c06cc000
[ 0.000000] Normal zone: 384 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 49152 pages, LIFO batch:15
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 48768
[ 0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2708.boardrev=0x2 bcm2708.serial=0xb3c91a9a smsc95xx.macaddr=B8:27:EB:C9:1A:9A sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0xec00000 vc_mem.mem_size=0x10000000 dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait debug
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 179648K/196608K available (4492K kernel code, 238K rwdata, 1340K rodata, 143K init, 701K bss, 16960K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xcc800000 - 0xff000000 ( 808 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xcc000000 ( 192 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc05ba210 (5833 kB)
[ 0.000000] .init : 0xc05bb000 - 0xc05defe4 ( 144 kB)
[ 0.000000] .data : 0xc05e0000 - 0xc061b8c0 ( 239 kB)
[ 0.000000] .bss : 0xc061b8cc - 0xc06cb088 ( 702 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:394
[ 0.000000] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] Console: colour dummy device 80x30
[ 0.000403] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
[ 0.000427] pid_max: default: 32768 minimum: 301
[ 0.000918] Mount-cache hash table entries: 512
[ 0.001722] Initializing cgroup subsys memory
[ 0.001801] Initializing cgroup subsys devices
[ 0.001820] Initializing cgroup subsys freezer
[ 0.001836] Initializing cgroup subsys blkio
[ 0.001963] CPU: Testing write buffer coherency: ok
[ 0.002422] Setting up static identity map for 0xc04461a8 - 0xc0446204
[ 0.004356] devtmpfs: initialized
[ 0.020651] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
[ 0.022182] NET: Registered protocol family 16
[ 0.027441] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[ 0.028048] cpuidle: using governor ladder
[ 0.028070] cpuidle: using governor menu
[ 0.028501] bcm2708.uart_clock = 0
[ 0.030443] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[ 0.030464] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.030478] mailbox: Broadcom VideoCore Mailbox driver
[ 0.030553] bcm2708_vcio: mailbox at f200b880
[ 0.030637] bcm_power: Broadcom power driver
[ 0.030656] bcm_power_open() -> 0
[ 0.030667] bcm_power_request(0, 8)
[ 0.531373] bcm_mailbox_read -> 00000080, 0
[ 0.531391] bcm_power_request -> 0
[ 0.531629] Serial: AMBA PL011 UART driver
[ 0.531779] dev:f1: ttyAMA0 at MMIO 0x20201000 (irq = 83, base_baud = 0) is a PL011 rev3
[ 0.912882] console [ttyAMA0] enabled
[ 0.939493] bio: create slab <bio-0> at 0
[ 0.944793] SCSI subsystem initialized
[ 0.948741] usbcore: registered new interface driver usbfs
[ 0.954412] usbcore: registered new interface driver hub
[ 0.959943] usbcore: registered new device driver usb
[ 0.966524] Switched to clocksource stc
[ 0.970744] FS-Cache: Loaded
[ 0.973877] CacheFiles: Loaded
[ 0.989858] NET: Registered protocol family 2
[ 0.995342] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 1.002664] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 1.009101] TCP: Hash tables configured (established 2048 bind 2048)
[ 1.015521] TCP: reno registered
[ 1.018804] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 1.024651] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 1.031408] NET: Registered protocol family 1
[ 1.036316] RPC: Registered named UNIX socket transport module.
[ 1.042339] RPC: Registered udp transport module.
[ 1.047076] RPC: Registered tcp transport module.
[ 1.051776] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.059137] bcm2708_dma: DMA manager at f2007000
[ 1.063839] bcm2708_gpio: bcm2708_gpio_probe c05eded0
[ 1.069393] vc-mem: phys_addr:0x00000000 mem_base=0x0ec00000 mem_size:0x10000000(256 MiB)
[ 1.078950] audit: initializing netlink socket (disabled)
[ 1.084416] type=2000 audit(0.930:1): initialized
[ 1.252395] VFS: Disk quotas dquot_6.5.2
[ 1.256757] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.265585] FS-Cache: Netfs 'nfs' registered for caching
[ 1.272521] NFS: Registering the id_resolver key type
[ 1.277787] Key type id_resolver registered
[ 1.281971] Key type id_legacy registered
[ 1.286788] msgmni has been set to 366
[ 1.292719] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.300532] io scheduler noop registered
[ 1.304459] io scheduler deadline registered
[ 1.309165] io scheduler cfq registered (default)
[ 1.315176] BCM2708FB: allocated DMA memory 4bc00000
[ 1.320324] BCM2708FB: allocated DMA channel 0 @ f2007000
[ 1.334178] Console: switching to colour frame buffer device 82x26
[ 1.426593] uart-pl011 dev:f1: no DMA platform data
[ 1.431522] kgdb: Registered I/O driver kgdboc.
[ 1.436794] vc-cma: Videocore CMA driver
[ 1.440719] vc-cma: vc_cma_base = 0x00000000
[ 1.445413] vc-cma: vc_cma_size = 0x00000000 (0 MiB)
[ 1.450862] vc-cma: vc_cma_initial = 0x00000000 (0 MiB)
[ 1.465706] brd: module loaded
[ 1.474099] loop: module loaded
[ 1.477624] vchiq: vchiq_init_state: slot_zero = 0xcb800000, is_master = 0
[ 1.485326] Loading iSCSI transport class v2.0-870.
[ 1.491440] usbcore: registered new interface driver smsc95xx
[ 1.497469] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 1.703404] Core Release: 2.80a
[ 1.706644] Setting default values for core params
[ 1.711463] Finished setting default values for core params
[ 1.917202] Using Buffer DMA mode
[ 1.920520] Periodic Transfer Interrupt Enhancement - disabled
[ 1.926341] Multiprocessor Interrupt Enhancement - disabled
[ 1.931942] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 1.936298] Dedicated Tx FIFOs mode
[ 1.940155] WARN::dwc_otg_hcd_init:1042: FIQ DMA bounce buffers: virt = 0xcbc14000 dma = 0x4bc14000 len=9024
[ 1.950045] FIQ FSM acceleration enabled for :
[ 1.950045] Non-periodic Split Transactions
[ 1.950045] Periodic Split Transactions
[ 1.950045] High-Speed Isochronous Endpoints
[ 1.966762] dwc_otg: Microframe scheduler enabled
[ 1.971526] WARN::hcd_init:473: FIQ at 0xc03207c4
[ 1.976227] WARN::hcd_init:474: FIQ ASM at 0xc0320a78 length 36
[ 1.982195] WARN::hcd_init:500: MPHI regs_base at 0xcc806000
[ 1.987903] dwc_otg bcm2708_usb: DWC OTG Controller
[ 1.992822] dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1
[ 2.000126] dwc_otg bcm2708_usb: irq 32, io mem 0x00000000
[ 2.005630] Init: Port Power? op_state=1
[ 2.009585] Init: Power Port (0)
[ 2.013110] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.019948] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.027199] usb usb1: Product: DWC OTG Controller
[ 2.031902] usb usb1: Manufacturer: Linux 3.12.21 dwc_otg_hcd
[ 2.037676] usb usb1: SerialNumber: bcm2708_usb
[ 2.043079] hub 1-0:1.0: USB hub found
[ 2.046988] hub 1-0:1.0: 1 port detected
[ 2.051393] dwc_otg: FIQ enabled
[ 2.054622] dwc_otg: NAK holdoff enabled
[ 2.058645] dwc_otg: FIQ split-transaction FSM enabled
[ 2.063793] Module dwc_common_port init
[ 2.068120] usbcore: registered new interface driver usb-storage
[ 2.074463] mousedev: PS/2 mouse device common for all mice
[ 2.080758] bcm2835-cpufreq: min=700000 max=700000 cur=700000
[ 2.086756] bcm2835-cpufreq: switching to governor powersave
[ 2.092416] bcm2835-cpufreq: switching to governor powersave
[ 2.098226] sdhci: Secure Digital Host Controller Interface driver
[ 2.104400] sdhci: Copyright(c) Pierre Ossman
[ 2.108866] sdhci: Enable low-latency mode
[ 2.156586] mmc0: SDHCI controller on BCM2708_Arasan [platform] using platform's DMA
[ 2.164575] mmc0: BCM2708 SDHC host at 0x20300000 DMA 2 IRQ 77
[ 2.170665] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.178455] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.191938] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.197665] usbcore: registered new interface driver usbhid
[ 2.205326] usbhid: USB HID core driver
[ 2.213897] TCP: cubic registered
[ 2.219357] Initializing XFRM netlink socket
[ 2.223730] NET: Registered protocol family 17
[ 2.231663] Key type dns_resolver registered
[ 2.240533] registered taskstats version 1
ø[ 2.245890] Waiting for root device /dev/mmcblk0p2...
[ 2.251282] Indeed it is in host mode hprt0 = 00021501
[ 2.318637] mmc0: read SD Status register (SSR) after 4 attempts
[ 2.346594] mmc0: new high speed SDHC card at address 0002
[ 2.353793] mmcblk0: mmc0:0002 00000 7.41 GiB
[ 2.359987] mmcblk0: p1 p2
[ 2.476623] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 2.496562] Indeed it is in host mode hprt0 = 00001101
[ 2.756914] usb 1-1: New USB device found, idVendor=0424, idProduct=9512
[ 2.763625] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.787308] hub 1-1:1.0: USB hub found
[ 2.791180] hub 1-1:1.0: 3 ports detected
[ 3.086663] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 3.196929] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 3.203815] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.229433] smsc95xx v1.0.4
[ 3.300743] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:c9:1a:9a
[ 3.824626] EXT4-fs (mmcblk0p2): recovery complete
[ 3.837184] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 3.845347] VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 3.851674] devtmpfs: mounted
[ 3.855117] Freeing unused kernel memory: 140K (c05bb000 - c05de000)
øøINIT: øversion 2.88 bootingø
øStarting udev
[ 4.632666] udevd[74]: starting version 182
[ 5.476926] bcm2708_spi bcm2708_spi.0: master is unqueued, this is deprecated
[ 5.739363] EXT4-fs (mmcblk0p2): re-mounted. Opts: data=ordered
Starting Bootlog daemon: bootlogd.
[ 5.974030] bcm2708_spi bcm2708_spi.0: SPI Controller at 0x20204000 (irq 80)
[ 6.534489] bcm2708_i2c_init_pinmode(0,0)
[ 6.633704] bcm2708_i2c_init_pinmode(0,1)
vm.min_free_kbytes = 8192
Wed Dec 17 22:41:00 UTC 2014
INIT: Entering runlevel: 5
Configuring network interfaces... [ 7.007207] bcm2708_i2c bcm2708_i2c.0: BSC0 Controller at 0x20205000 (irq 79) (baudrate 100000)
[ 7.079572] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
udhcpc (v1.22.1) started
Sending discover...
[ 7.418992] bcm2708_i2c_init_pinmode(1,2)
[ 7.423016] bcm2708_i2c_init_pinmode(1,3)
[ 7.727159] bcm2708_i2c bcm2708_i2c.1: BSC1 Controller at 0x20804000 (irq 79) (baudrate 100000)
udevadm settle - timeout of 3 seconds reached, the event queue contains:
/sys/devices/dev:f1 (1083)
/sys/devices/platform/alarmtimer (1084)
/sys/devices/platform/bcm2708-i2s.0 (1085)
/sys/devices/platform/bcm2708_dma.0 (1086)
/sys/devices/platform/bcm2708_fb (1087)
/sys/devices/platform/bcm2708_gpio (1088)
/sys/devices/platform/bcm2708_i2c.0 (1089)
/sys/devices/platform/bcm2708_i2c.1 (1090)
/sys/devices/platform/bcm2708_powerman.0 (1091)
/sys/devices/platform/bcm2708_sdhci.0 (1092)
/sys/devices/platform/bcm2708_spi.0 (1093)
/sys/devices/platform/bcm2708_systemtimer (1094)
/sys/devices/platform/bcm2708_usb (1095)
/sys/devices/platform/bcm2708_usb/usb1 (1096)
/sys/devices/platform/bcm2708_usb/usb1/1-0:1.0 (1097)
/sys/devices/platform/bcm2708_usb/usb1/1-1 (1098)
/sys/devices/platform/bcm2708_usb/usb1/1-1/1-1.1 (1099)
/sys/devices/platform/bcm2708_usb/usb1/1-1/1-1.1/1-1.1:1.0 (1100)
/sys/devices/platform/bcm2708_usb/usb1/1-1/1-1.1/1-1.1:1.0/net/eth0 (1101)
/sys/devices/platform/bcm2708_usb/usb1/1-1/1-1:1.0 (1102)
/sys/devices/platform/bcm2708_vcio (1103)
/sys/devices/platform/bcm2835_AUD0.0 (1104)
/sys/devices/platform/bcm2835_AUD1.1 (1105)
/sys/devices/platform/bcm2835_AUD2.2 (1106)
/sys/devices/platform/bcm2835_AUD3.3 (1107)
/sys/devices/platform/bcm2835_AUD4.4 (1108)
/sys/devices/platform/bcm2835_AUD5.5 (1109)
/sys/devices/platform/bcm2835_AUD6.6 (1110)
/sys/devices/platform/bcm2835_AUD7.7 (1111)
/sys/devices/platform/bcm2835_hwmon.0 (1112)
/sys/devices/platform/bcm2835_thermal.0 (1113)
/sys/devices/platform/leds-gpio (1114)
/sys/devices/platform/mmc_host/mmc0/mmc0:0002 (1116)
/sys/devices/platform/mmc_host/mmc0/mmc0:0002/block/m[ 8.095002] bcm2708-i2s bcm2708-i2s.0: Failed to create debugfs directory
mcblk0 (1117)
/sys/devices/platform/mmc_host/mmc0/mmc0:0002/block/mmcblk0/mmcblk0p1 (1118)
/sys/devices/platform/mmc_host/mmc0/mmc0:0002/block/mmcblk0/mmcblk0p2 (1119)
/sys/devices/platform/pcm1794a-codec (1120)
/sys/devices/platform/pcm5102a-codec (1121)
/sys/devices/platform/serial8250.0 (1122)
/sys/devices/platform/snd-hifiberry-dac.0 (1123)
/sys/devices/platform/snd-hifiberry-digi.0 (1124)
/sys/devices/platform/snd-rpi-dac.0 (1125)
/sys/devices/platform/snd-rpi-iqaudio-dac.0 (1126)
/sys/devices/platform/w1-gpio (1127)
/sys/devices/virtual/block/ram11 (1169)
/sys/devices/virtual/block/ram12 (1170)
/sys/devices/virtual/block/ram13 (1171)
/sys/devices/virtual/block/ram14 (1172)
/sys/devices/virtual/block/ram15 (1173)
/sys/devices/virtual/block/ram2 (1174)
/sys/devices/virtual/block/ram3 (1175)
/sys/devices/virtual/block/ram4 (1176)
[ 8.683144] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
Sending discover...
Sending select f[ 10.369921] pcm512x 1-004c: Failed to reset device: -5
or 172.30.30.53.[ 10.376213] pcm512x: probe of 1-004c failed with error -5
..
Lease of 172.30.30.53 obtained, lease time 259200
/etc/udhcpc.d/50default: Adding DNS 172.30.30.254
done.
Starting syslogd/klogd: done
Stopping Bootlog daemon: bootlogd.
øø
Poky (Yocto Project Reference Distro) 1.6.2 raspberrypi /dev/ttyAMA0
raspberrypi login: root
root@raspberrypi:~# pwd
/home/root
root@raspberrypi:~#
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [meta-raspberrypi] Image will halt soon after boot
2014-12-18 7:22 [meta-raspberrypi] Image will halt soon after boot Petter Gustad
@ 2014-12-18 9:12 ` Maciej Borzecki
2014-12-18 15:42 ` Petter Gustad
2014-12-18 9:54 ` ChenQi
1 sibling, 1 reply; 7+ messages in thread
From: Maciej Borzecki @ 2014-12-18 9:12 UTC (permalink / raw)
To: Petter Gustad; +Cc: yocto@yoctoproject.org
On 12/18 08:22, Petter Gustad wrote:
>
> I've run "bitbake rpi-hwup-image" using the daisy branch:
>
> meta-yocto-bsp = "daisy:1e668ccf1a05c5d730de9747bc1c2b0446bda556"
> meta-raspberrypi.git = "daisy:946b69299737cc2f1378c864f1b9075280db1b53"
>
> However, whenever I boot the created sdimage it will lock up during
> boot. Typically I will see some garbage on the serial console.
> Sometimes I'm able to log in, but then then I get no response (as in
> the below session). Putting a pre-compiled distribution on the same
> sdcard will boot just fine.
>
> Does anybody else observe this behavior?
Have you seen the same on 1.7 or current master? I'm using a number of
Yocto built images (sone on 1.7.x, other mostly follow poky +
meta-raspberrypi master branches) and things seem to work just fine.
--
Maciej Borzęcki
Senior Software Developer at Open-RnD Sp. z o.o., Poland
www.open-rnd.pl
mobile: +48 889 117 365, fax: +48 42 657 9079
Niniejsza wiadomość wraz z załącznikami może
zawierać chronione prawem lub poufne informacje i została
wysłana wyłącznie do wiadomości i użytku osób, do których
została zaadresowana. Jeśli wiadomość została otrzymana
przypadkowo zabrania się jej kopiowania lub rozsyłania do osób
trzecich. W takim przypadku uprasza się o natychmiastowe
zniszczenie wiadomości oraz poinformowanie nadawcy o
zaistniałej sytuacji za pomocą wiadomości zwrotnej.
Dziękujemy.
This message, including any attachments hereto,
may contain privileged or confidential information and is sent
solely for the attention and use of the intended addressee(s).
If you are not an intended addressee, you may neither use this
message nor copy or deliver it to anyone. In such case, you
should immediately destroy this message and kindly notify the
sender by reply email. Thank you.
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [meta-raspberrypi] Image will halt soon after boot
2014-12-18 9:12 ` Maciej Borzecki
@ 2014-12-18 15:42 ` Petter Gustad
2014-12-18 15:45 ` Maciej Borzecki
0 siblings, 1 reply; 7+ messages in thread
From: Petter Gustad @ 2014-12-18 15:42 UTC (permalink / raw)
To: maciej.borzecki; +Cc: yocto
From: Maciej Borzecki <maciej.borzecki@open-rnd.pl>
Subject: Re: [yocto] [meta-raspberrypi] Image will halt soon after boot
Date: Thu, 18 Dec 2014 10:12:28 +0100
> Have you seen the same on 1.7 or current master? I'm using a number of
> Yocto built images (sone on 1.7.x, other mostly follow poky +
> meta-raspberrypi master branches) and things seem to work just fine.
Thanks! I just tried the master branch as given below and it works
fine. I will switch to a more recent release. However, I can't seem to
find a dizzy branch in meta-raspberrypi?
Best regards
//Petter
meta-yocto-bsp = "master:8657c2fd57600e0b0eaf2a14692de7453c78e1bb"
meta-raspberrypi.git = "master:6c6f44136f7e1c97bc45be118a48bd9b1fef1072"
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [meta-raspberrypi] Image will halt soon after boot
2014-12-18 15:42 ` Petter Gustad
@ 2014-12-18 15:45 ` Maciej Borzecki
2015-01-25 22:35 ` Andrei Gherzan
0 siblings, 1 reply; 7+ messages in thread
From: Maciej Borzecki @ 2014-12-18 15:45 UTC (permalink / raw)
To: Petter Gustad; +Cc: yocto
On 12/18 16:42, Petter Gustad wrote:
> From: Maciej Borzecki <maciej.borzecki@open-rnd.pl>
> Subject: Re: [yocto] [meta-raspberrypi] Image will halt soon after boot
> Date: Thu, 18 Dec 2014 10:12:28 +0100
>
> > Have you seen the same on 1.7 or current master? I'm using a number of
> > Yocto built images (sone on 1.7.x, other mostly follow poky +
> > meta-raspberrypi master branches) and things seem to work just fine.
>
> Thanks! I just tried the master branch as given below and it works
> fine. I will switch to a more recent release. However, I can't seem to
> find a dizzy branch in meta-raspberrypi?
It seems that thee is no dizzy branch at all in meta-raspberrypi. You
might want to ping the layer's maintainers about that.
--
Maciej Borzęcki
Senior Software Developer at Open-RnD Sp. z o.o., Poland
www.open-rnd.pl
mobile: +48 889 117 365, fax: +48 42 657 9079
Niniejsza wiadomość wraz z załącznikami może
zawierać chronione prawem lub poufne informacje i została
wysłana wyłącznie do wiadomości i użytku osób, do których
została zaadresowana. Jeśli wiadomość została otrzymana
przypadkowo zabrania się jej kopiowania lub rozsyłania do osób
trzecich. W takim przypadku uprasza się o natychmiastowe
zniszczenie wiadomości oraz poinformowanie nadawcy o
zaistniałej sytuacji za pomocą wiadomości zwrotnej.
Dziękujemy.
This message, including any attachments hereto,
may contain privileged or confidential information and is sent
solely for the attention and use of the intended addressee(s).
If you are not an intended addressee, you may neither use this
message nor copy or deliver it to anyone. In such case, you
should immediately destroy this message and kindly notify the
sender by reply email. Thank you.
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [meta-raspberrypi] Image will halt soon after boot
2014-12-18 15:45 ` Maciej Borzecki
@ 2015-01-25 22:35 ` Andrei Gherzan
2015-01-27 7:40 ` Andrei Gherzan
0 siblings, 1 reply; 7+ messages in thread
From: Andrei Gherzan @ 2015-01-25 22:35 UTC (permalink / raw)
To: Maciej Borzecki; +Cc: Yocto Project
[-- Attachment #1: Type: text/plain, Size: 2202 bytes --]
Dizzy branch on its way. Maintainer received the ping.
On Thu, Dec 18, 2014 at 5:45 PM, Maciej Borzecki <
maciej.borzecki@open-rnd.pl> wrote:
> On 12/18 16:42, Petter Gustad wrote:
> > From: Maciej Borzecki <maciej.borzecki@open-rnd.pl>
> > Subject: Re: [yocto] [meta-raspberrypi] Image will halt soon after boot
> > Date: Thu, 18 Dec 2014 10:12:28 +0100
> >
> > > Have you seen the same on 1.7 or current master? I'm using a number of
> > > Yocto built images (sone on 1.7.x, other mostly follow poky +
> > > meta-raspberrypi master branches) and things seem to work just fine.
> >
> > Thanks! I just tried the master branch as given below and it works
> > fine. I will switch to a more recent release. However, I can't seem to
> > find a dizzy branch in meta-raspberrypi?
>
> It seems that thee is no dizzy branch at all in meta-raspberrypi. You
> might want to ping the layer's maintainers about that.
>
> --
> Maciej Borzęcki
> Senior Software Developer at Open-RnD Sp. z o.o., Poland
> www.open-rnd.pl
> mobile: +48 889 117 365, fax: +48 42 657 9079
>
>
> Niniejsza wiadomość wraz z załącznikami może
> zawierać chronione prawem lub poufne informacje i została
> wysłana wyłącznie do wiadomości i użytku osób, do których
> została zaadresowana. Jeśli wiadomość została otrzymana
> przypadkowo zabrania się jej kopiowania lub rozsyłania do osób
> trzecich. W takim przypadku uprasza się o natychmiastowe
> zniszczenie wiadomości oraz poinformowanie nadawcy o
> zaistniałej sytuacji za pomocą wiadomości zwrotnej.
> Dziękujemy.
>
> This message, including any attachments hereto,
> may contain privileged or confidential information and is sent
> solely for the attention and use of the intended addressee(s).
> If you are not an intended addressee, you may neither use this
> message nor copy or deliver it to anyone. In such case, you
> should immediately destroy this message and kindly notify the
> sender by reply email. Thank you.
> --
> _______________________________________________
> yocto mailing list
> yocto@yoctoproject.org
> https://lists.yoctoproject.org/listinfo/yocto
>
--
*Andrei Gherzan*
[-- Attachment #2: Type: text/html, Size: 3369 bytes --]
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [meta-raspberrypi] Image will halt soon after boot
2015-01-25 22:35 ` Andrei Gherzan
@ 2015-01-27 7:40 ` Andrei Gherzan
0 siblings, 0 replies; 7+ messages in thread
From: Andrei Gherzan @ 2015-01-27 7:40 UTC (permalink / raw)
To: Maciej Borzecki; +Cc: Yocto Project
[-- Attachment #1: Type: text/plain, Size: 2368 bytes --]
Dizzy branch created. Enjoy!
On Jan 26, 2015 12:35 AM, "Andrei Gherzan" <andrei@gherzan.ro> wrote:
> Dizzy branch on its way. Maintainer received the ping.
>
> On Thu, Dec 18, 2014 at 5:45 PM, Maciej Borzecki <
> maciej.borzecki@open-rnd.pl> wrote:
>
>> On 12/18 16:42, Petter Gustad wrote:
>> > From: Maciej Borzecki <maciej.borzecki@open-rnd.pl>
>> > Subject: Re: [yocto] [meta-raspberrypi] Image will halt soon after boot
>> > Date: Thu, 18 Dec 2014 10:12:28 +0100
>> >
>> > > Have you seen the same on 1.7 or current master? I'm using a number of
>> > > Yocto built images (sone on 1.7.x, other mostly follow poky +
>> > > meta-raspberrypi master branches) and things seem to work just fine.
>> >
>> > Thanks! I just tried the master branch as given below and it works
>> > fine. I will switch to a more recent release. However, I can't seem to
>> > find a dizzy branch in meta-raspberrypi?
>>
>> It seems that thee is no dizzy branch at all in meta-raspberrypi. You
>> might want to ping the layer's maintainers about that.
>>
>> --
>> Maciej Borzęcki
>> Senior Software Developer at Open-RnD Sp. z o.o., Poland
>> www.open-rnd.pl
>> mobile: +48 889 117 365, fax: +48 42 657 9079
>>
>>
>> Niniejsza wiadomość wraz z załącznikami może
>> zawierać chronione prawem lub poufne informacje i została
>> wysłana wyłącznie do wiadomości i użytku osób, do których
>> została zaadresowana. Jeśli wiadomość została otrzymana
>> przypadkowo zabrania się jej kopiowania lub rozsyłania do osób
>> trzecich. W takim przypadku uprasza się o natychmiastowe
>> zniszczenie wiadomości oraz poinformowanie nadawcy o
>> zaistniałej sytuacji za pomocą wiadomości zwrotnej.
>> Dziękujemy.
>>
>> This message, including any attachments hereto,
>> may contain privileged or confidential information and is sent
>> solely for the attention and use of the intended addressee(s).
>> If you are not an intended addressee, you may neither use this
>> message nor copy or deliver it to anyone. In such case, you
>> should immediately destroy this message and kindly notify the
>> sender by reply email. Thank you.
>> --
>> _______________________________________________
>> yocto mailing list
>> yocto@yoctoproject.org
>> https://lists.yoctoproject.org/listinfo/yocto
>>
>
>
>
> --
> *Andrei Gherzan*
>
[-- Attachment #2: Type: text/html, Size: 3699 bytes --]
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [meta-raspberrypi] Image will halt soon after boot
2014-12-18 7:22 [meta-raspberrypi] Image will halt soon after boot Petter Gustad
2014-12-18 9:12 ` Maciej Borzecki
@ 2014-12-18 9:54 ` ChenQi
1 sibling, 0 replies; 7+ messages in thread
From: ChenQi @ 2014-12-18 9:54 UTC (permalink / raw)
To: yocto
If the problem does not appear on first boot, then I guess it might be
related to udev-cache.
You could try to disable udev-cache and reboot again to check.
Regards,
Chen Qi
On 12/18/2014 03:22 PM, Petter Gustad wrote:
> I've run "bitbake rpi-hwup-image" using the daisy branch:
>
> meta-yocto-bsp = "daisy:1e668ccf1a05c5d730de9747bc1c2b0446bda556"
> meta-raspberrypi.git = "daisy:946b69299737cc2f1378c864f1b9075280db1b53"
>
> However, whenever I boot the created sdimage it will lock up during
> boot. Typically I will see some garbage on the serial console.
> Sometimes I'm able to log in, but then then I get no response (as in
> the below session). Putting a pre-compiled distribution on the same
> sdcard will boot just fine.
>
> Does anybody else observe this behavior?
>
> Is there a specific meta-raspberrypi mailing list?
>
> Best regards
> //Petter
>
> [ 0.000000] Booting Linux on physical CPU 0x0
> [ 0.000000] Initializing cgroup subsys cpu
> [ 0.000000] Initializing cgroup subsys cpuacct
> [ 0.000000] Linux version 3.12.21 (yocto@pangea) (gcc version 4.8.2 (GCC) ) #1 PREEMPT Wed Dec 17 22:58:01 CET 2014
> [ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d
> [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
> [ 0.000000] Machine: BCM2708
> [ 0.000000] cma: CMA: reserved 8 MiB at 0b800000
> [ 0.000000] Memory policy: ECC disabled, Data cache writeback
> [ 0.000000] On node 0 totalpages: 49152
> [ 0.000000] free_area_init_node: node 0, pgdat c061ada0, node_mem_map c06cc000
> [ 0.000000] Normal zone: 384 pages used for memmap
> [ 0.000000] Normal zone: 0 pages reserved
> [ 0.000000] Normal zone: 49152 pages, LIFO batch:15
> [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
> [ 0.000000] pcpu-alloc: [0] 0
> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 48768
> [ 0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2708.boardrev=0x2 bcm2708.serial=0xb3c91a9a smsc95xx.macaddr=B8:27:EB:C9:1A:9A sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0xec00000 vc_mem.mem_size=0x10000000 dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait debug
> [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> [ 0.000000] Memory: 179648K/196608K available (4492K kernel code, 238K rwdata, 1340K rodata, 143K init, 701K bss, 16960K reserved)
> [ 0.000000] Virtual kernel memory layout:
> [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
> [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
> [ 0.000000] vmalloc : 0xcc800000 - 0xff000000 ( 808 MB)
> [ 0.000000] lowmem : 0xc0000000 - 0xcc000000 ( 192 MB)
> [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
> [ 0.000000] .text : 0xc0008000 - 0xc05ba210 (5833 kB)
> [ 0.000000] .init : 0xc05bb000 - 0xc05defe4 ( 144 kB)
> [ 0.000000] .data : 0xc05e0000 - 0xc061b8c0 ( 239 kB)
> [ 0.000000] .bss : 0xc061b8cc - 0xc06cb088 ( 702 kB)
> [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> [ 0.000000] Preemptible hierarchical RCU implementation.
> [ 0.000000] NR_IRQS:394
> [ 0.000000] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
> [ 0.000000] Switching to timer-based delay loop
> [ 0.000000] Console: colour dummy device 80x30
> [ 0.000403] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000)
> [ 0.000427] pid_max: default: 32768 minimum: 301
> [ 0.000918] Mount-cache hash table entries: 512
> [ 0.001722] Initializing cgroup subsys memory
> [ 0.001801] Initializing cgroup subsys devices
> [ 0.001820] Initializing cgroup subsys freezer
> [ 0.001836] Initializing cgroup subsys blkio
> [ 0.001963] CPU: Testing write buffer coherency: ok
> [ 0.002422] Setting up static identity map for 0xc04461a8 - 0xc0446204
> [ 0.004356] devtmpfs: initialized
> [ 0.020651] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
> [ 0.022182] NET: Registered protocol family 16
> [ 0.027441] DMA: preallocated 4096 KiB pool for atomic coherent allocations
> [ 0.028048] cpuidle: using governor ladder
> [ 0.028070] cpuidle: using governor menu
> [ 0.028501] bcm2708.uart_clock = 0
> [ 0.030443] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
> [ 0.030464] hw-breakpoint: maximum watchpoint size is 4 bytes.
> [ 0.030478] mailbox: Broadcom VideoCore Mailbox driver
> [ 0.030553] bcm2708_vcio: mailbox at f200b880
> [ 0.030637] bcm_power: Broadcom power driver
> [ 0.030656] bcm_power_open() -> 0
> [ 0.030667] bcm_power_request(0, 8)
> [ 0.531373] bcm_mailbox_read -> 00000080, 0
> [ 0.531391] bcm_power_request -> 0
> [ 0.531629] Serial: AMBA PL011 UART driver
> [ 0.531779] dev:f1: ttyAMA0 at MMIO 0x20201000 (irq = 83, base_baud = 0) is a PL011 rev3
> [ 0.912882] console [ttyAMA0] enabled
> [ 0.939493] bio: create slab <bio-0> at 0
> [ 0.944793] SCSI subsystem initialized
> [ 0.948741] usbcore: registered new interface driver usbfs
> [ 0.954412] usbcore: registered new interface driver hub
> [ 0.959943] usbcore: registered new device driver usb
> [ 0.966524] Switched to clocksource stc
> [ 0.970744] FS-Cache: Loaded
> [ 0.973877] CacheFiles: Loaded
> [ 0.989858] NET: Registered protocol family 2
> [ 0.995342] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
> [ 1.002664] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
> [ 1.009101] TCP: Hash tables configured (established 2048 bind 2048)
> [ 1.015521] TCP: reno registered
> [ 1.018804] UDP hash table entries: 256 (order: 0, 4096 bytes)
> [ 1.024651] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> [ 1.031408] NET: Registered protocol family 1
> [ 1.036316] RPC: Registered named UNIX socket transport module.
> [ 1.042339] RPC: Registered udp transport module.
> [ 1.047076] RPC: Registered tcp transport module.
> [ 1.051776] RPC: Registered tcp NFSv4.1 backchannel transport module.
> [ 1.059137] bcm2708_dma: DMA manager at f2007000
> [ 1.063839] bcm2708_gpio: bcm2708_gpio_probe c05eded0
> [ 1.069393] vc-mem: phys_addr:0x00000000 mem_base=0x0ec00000 mem_size:0x10000000(256 MiB)
> [ 1.078950] audit: initializing netlink socket (disabled)
> [ 1.084416] type=2000 audit(0.930:1): initialized
> [ 1.252395] VFS: Disk quotas dquot_6.5.2
> [ 1.256757] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> [ 1.265585] FS-Cache: Netfs 'nfs' registered for caching
> [ 1.272521] NFS: Registering the id_resolver key type
> [ 1.277787] Key type id_resolver registered
> [ 1.281971] Key type id_legacy registered
> [ 1.286788] msgmni has been set to 366
> [ 1.292719] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
> [ 1.300532] io scheduler noop registered
> [ 1.304459] io scheduler deadline registered
> [ 1.309165] io scheduler cfq registered (default)
> [ 1.315176] BCM2708FB: allocated DMA memory 4bc00000
> [ 1.320324] BCM2708FB: allocated DMA channel 0 @ f2007000
> [ 1.334178] Console: switching to colour frame buffer device 82x26
> [ 1.426593] uart-pl011 dev:f1: no DMA platform data
> [ 1.431522] kgdb: Registered I/O driver kgdboc.
> [ 1.436794] vc-cma: Videocore CMA driver
> [ 1.440719] vc-cma: vc_cma_base = 0x00000000
> [ 1.445413] vc-cma: vc_cma_size = 0x00000000 (0 MiB)
> [ 1.450862] vc-cma: vc_cma_initial = 0x00000000 (0 MiB)
> [ 1.465706] brd: module loaded
> [ 1.474099] loop: module loaded
> [ 1.477624] vchiq: vchiq_init_state: slot_zero = 0xcb800000, is_master = 0
> [ 1.485326] Loading iSCSI transport class v2.0-870.
> [ 1.491440] usbcore: registered new interface driver smsc95xx
> [ 1.497469] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
> [ 1.703404] Core Release: 2.80a
> [ 1.706644] Setting default values for core params
> [ 1.711463] Finished setting default values for core params
> [ 1.917202] Using Buffer DMA mode
> [ 1.920520] Periodic Transfer Interrupt Enhancement - disabled
> [ 1.926341] Multiprocessor Interrupt Enhancement - disabled
> [ 1.931942] OTG VER PARAM: 0, OTG VER FLAG: 0
> [ 1.936298] Dedicated Tx FIFOs mode
> [ 1.940155] WARN::dwc_otg_hcd_init:1042: FIQ DMA bounce buffers: virt = 0xcbc14000 dma = 0x4bc14000 len=9024
> [ 1.950045] FIQ FSM acceleration enabled for :
> [ 1.950045] Non-periodic Split Transactions
> [ 1.950045] Periodic Split Transactions
> [ 1.950045] High-Speed Isochronous Endpoints
> [ 1.966762] dwc_otg: Microframe scheduler enabled
> [ 1.971526] WARN::hcd_init:473: FIQ at 0xc03207c4
> [ 1.976227] WARN::hcd_init:474: FIQ ASM at 0xc0320a78 length 36
> [ 1.982195] WARN::hcd_init:500: MPHI regs_base at 0xcc806000
> [ 1.987903] dwc_otg bcm2708_usb: DWC OTG Controller
> [ 1.992822] dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1
> [ 2.000126] dwc_otg bcm2708_usb: irq 32, io mem 0x00000000
> [ 2.005630] Init: Port Power? op_state=1
> [ 2.009585] Init: Power Port (0)
> [ 2.013110] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
> [ 2.019948] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> [ 2.027199] usb usb1: Product: DWC OTG Controller
> [ 2.031902] usb usb1: Manufacturer: Linux 3.12.21 dwc_otg_hcd
> [ 2.037676] usb usb1: SerialNumber: bcm2708_usb
> [ 2.043079] hub 1-0:1.0: USB hub found
> [ 2.046988] hub 1-0:1.0: 1 port detected
> [ 2.051393] dwc_otg: FIQ enabled
> [ 2.054622] dwc_otg: NAK holdoff enabled
> [ 2.058645] dwc_otg: FIQ split-transaction FSM enabled
> [ 2.063793] Module dwc_common_port init
> [ 2.068120] usbcore: registered new interface driver usb-storage
> [ 2.074463] mousedev: PS/2 mouse device common for all mice
> [ 2.080758] bcm2835-cpufreq: min=700000 max=700000 cur=700000
> [ 2.086756] bcm2835-cpufreq: switching to governor powersave
> [ 2.092416] bcm2835-cpufreq: switching to governor powersave
> [ 2.098226] sdhci: Secure Digital Host Controller Interface driver
> [ 2.104400] sdhci: Copyright(c) Pierre Ossman
> [ 2.108866] sdhci: Enable low-latency mode
> [ 2.156586] mmc0: SDHCI controller on BCM2708_Arasan [platform] using platform's DMA
> [ 2.164575] mmc0: BCM2708 SDHC host at 0x20300000 DMA 2 IRQ 77
> [ 2.170665] sdhci-pltfm: SDHCI platform and OF driver helper
> [ 2.178455] ledtrig-cpu: registered to indicate activity on CPUs
> [ 2.191938] hidraw: raw HID events driver (C) Jiri Kosina
> [ 2.197665] usbcore: registered new interface driver usbhid
> [ 2.205326] usbhid: USB HID core driver
> [ 2.213897] TCP: cubic registered
> [ 2.219357] Initializing XFRM netlink socket
> [ 2.223730] NET: Registered protocol family 17
> [ 2.231663] Key type dns_resolver registered
> [ 2.240533] registered taskstats version 1
> ø[ 2.245890] Waiting for root device /dev/mmcblk0p2...
> [ 2.251282] Indeed it is in host mode hprt0 = 00021501
> [ 2.318637] mmc0: read SD Status register (SSR) after 4 attempts
> [ 2.346594] mmc0: new high speed SDHC card at address 0002
> [ 2.353793] mmcblk0: mmc0:0002 00000 7.41 GiB
> [ 2.359987] mmcblk0: p1 p2
> [ 2.476623] usb 1-1: new high-speed USB device number 2 using dwc_otg
> [ 2.496562] Indeed it is in host mode hprt0 = 00001101
> [ 2.756914] usb 1-1: New USB device found, idVendor=0424, idProduct=9512
> [ 2.763625] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
> [ 2.787308] hub 1-1:1.0: USB hub found
> [ 2.791180] hub 1-1:1.0: 3 ports detected
> [ 3.086663] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
> [ 3.196929] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
> [ 3.203815] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
> [ 3.229433] smsc95xx v1.0.4
> [ 3.300743] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:c9:1a:9a
> [ 3.824626] EXT4-fs (mmcblk0p2): recovery complete
> [ 3.837184] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
> [ 3.845347] VFS: Mounted root (ext4 filesystem) on device 179:2.
> [ 3.851674] devtmpfs: mounted
> [ 3.855117] Freeing unused kernel memory: 140K (c05bb000 - c05de000)
> øøINIT: øversion 2.88 bootingø
> øStarting udev
> [ 4.632666] udevd[74]: starting version 182
> [ 5.476926] bcm2708_spi bcm2708_spi.0: master is unqueued, this is deprecated
> [ 5.739363] EXT4-fs (mmcblk0p2): re-mounted. Opts: data=ordered
> Starting Bootlog daemon: bootlogd.
> [ 5.974030] bcm2708_spi bcm2708_spi.0: SPI Controller at 0x20204000 (irq 80)
> [ 6.534489] bcm2708_i2c_init_pinmode(0,0)
> [ 6.633704] bcm2708_i2c_init_pinmode(0,1)
> vm.min_free_kbytes = 8192
> Wed Dec 17 22:41:00 UTC 2014
> INIT: Entering runlevel: 5
> Configuring network interfaces... [ 7.007207] bcm2708_i2c bcm2708_i2c.0: BSC0 Controller at 0x20205000 (irq 79) (baudrate 100000)
> [ 7.079572] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
> udhcpc (v1.22.1) started
> Sending discover...
> [ 7.418992] bcm2708_i2c_init_pinmode(1,2)
> [ 7.423016] bcm2708_i2c_init_pinmode(1,3)
> [ 7.727159] bcm2708_i2c bcm2708_i2c.1: BSC1 Controller at 0x20804000 (irq 79) (baudrate 100000)
>
> udevadm settle - timeout of 3 seconds reached, the event queue contains:
> /sys/devices/dev:f1 (1083)
> /sys/devices/platform/alarmtimer (1084)
> /sys/devices/platform/bcm2708-i2s.0 (1085)
> /sys/devices/platform/bcm2708_dma.0 (1086)
> /sys/devices/platform/bcm2708_fb (1087)
> /sys/devices/platform/bcm2708_gpio (1088)
> /sys/devices/platform/bcm2708_i2c.0 (1089)
> /sys/devices/platform/bcm2708_i2c.1 (1090)
> /sys/devices/platform/bcm2708_powerman.0 (1091)
> /sys/devices/platform/bcm2708_sdhci.0 (1092)
> /sys/devices/platform/bcm2708_spi.0 (1093)
> /sys/devices/platform/bcm2708_systemtimer (1094)
> /sys/devices/platform/bcm2708_usb (1095)
> /sys/devices/platform/bcm2708_usb/usb1 (1096)
> /sys/devices/platform/bcm2708_usb/usb1/1-0:1.0 (1097)
> /sys/devices/platform/bcm2708_usb/usb1/1-1 (1098)
> /sys/devices/platform/bcm2708_usb/usb1/1-1/1-1.1 (1099)
> /sys/devices/platform/bcm2708_usb/usb1/1-1/1-1.1/1-1.1:1.0 (1100)
> /sys/devices/platform/bcm2708_usb/usb1/1-1/1-1.1/1-1.1:1.0/net/eth0 (1101)
> /sys/devices/platform/bcm2708_usb/usb1/1-1/1-1:1.0 (1102)
> /sys/devices/platform/bcm2708_vcio (1103)
> /sys/devices/platform/bcm2835_AUD0.0 (1104)
> /sys/devices/platform/bcm2835_AUD1.1 (1105)
> /sys/devices/platform/bcm2835_AUD2.2 (1106)
> /sys/devices/platform/bcm2835_AUD3.3 (1107)
> /sys/devices/platform/bcm2835_AUD4.4 (1108)
> /sys/devices/platform/bcm2835_AUD5.5 (1109)
> /sys/devices/platform/bcm2835_AUD6.6 (1110)
> /sys/devices/platform/bcm2835_AUD7.7 (1111)
> /sys/devices/platform/bcm2835_hwmon.0 (1112)
> /sys/devices/platform/bcm2835_thermal.0 (1113)
> /sys/devices/platform/leds-gpio (1114)
> /sys/devices/platform/mmc_host/mmc0/mmc0:0002 (1116)
> /sys/devices/platform/mmc_host/mmc0/mmc0:0002/block/m[ 8.095002] bcm2708-i2s bcm2708-i2s.0: Failed to create debugfs directory
> mcblk0 (1117)
> /sys/devices/platform/mmc_host/mmc0/mmc0:0002/block/mmcblk0/mmcblk0p1 (1118)
> /sys/devices/platform/mmc_host/mmc0/mmc0:0002/block/mmcblk0/mmcblk0p2 (1119)
> /sys/devices/platform/pcm1794a-codec (1120)
> /sys/devices/platform/pcm5102a-codec (1121)
> /sys/devices/platform/serial8250.0 (1122)
> /sys/devices/platform/snd-hifiberry-dac.0 (1123)
> /sys/devices/platform/snd-hifiberry-digi.0 (1124)
> /sys/devices/platform/snd-rpi-dac.0 (1125)
> /sys/devices/platform/snd-rpi-iqaudio-dac.0 (1126)
> /sys/devices/platform/w1-gpio (1127)
> /sys/devices/virtual/block/ram11 (1169)
> /sys/devices/virtual/block/ram12 (1170)
> /sys/devices/virtual/block/ram13 (1171)
> /sys/devices/virtual/block/ram14 (1172)
> /sys/devices/virtual/block/ram15 (1173)
> /sys/devices/virtual/block/ram2 (1174)
> /sys/devices/virtual/block/ram3 (1175)
> /sys/devices/virtual/block/ram4 (1176)
> [ 8.683144] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
> Sending discover...
> Sending select f[ 10.369921] pcm512x 1-004c: Failed to reset device: -5
> or 172.30.30.53.[ 10.376213] pcm512x: probe of 1-004c failed with error -5
> ..
> Lease of 172.30.30.53 obtained, lease time 259200
> /etc/udhcpc.d/50default: Adding DNS 172.30.30.254
> done.
> Starting syslogd/klogd: done
> Stopping Bootlog daemon: bootlogd.
> øø
> Poky (Yocto Project Reference Distro) 1.6.2 raspberrypi /dev/ttyAMA0
>
> raspberrypi login: root
> root@raspberrypi:~# pwd
> /home/root
> root@raspberrypi:~#
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2015-01-27 7:40 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-12-18 7:22 [meta-raspberrypi] Image will halt soon after boot Petter Gustad
2014-12-18 9:12 ` Maciej Borzecki
2014-12-18 15:42 ` Petter Gustad
2014-12-18 15:45 ` Maciej Borzecki
2015-01-25 22:35 ` Andrei Gherzan
2015-01-27 7:40 ` Andrei Gherzan
2014-12-18 9:54 ` ChenQi
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.