* [U-Boot] [PATCH] config: peach: Correct memory layout environment settings @ 2015-03-12 21:33 Sjoerd Simons 2015-03-23 21:04 ` Simon Glass 0 siblings, 1 reply; 11+ messages in thread From: Sjoerd Simons @ 2015-03-12 21:33 UTC (permalink / raw) To: u-boot The peach boards have their SDRAM start address at 0x20000000 instead of 0x40000000 which seems common for all other exynos5 based boards. This means the layout set in exynos5-common.h causes the kernel be loaded more then 128MB (at 0x42000000) away from memory start which breaks booting kernels with CONFIG_AUTO_ZRELADDR Define a custom MEM_LAYOUT_ENV_SETTINGS for both peach boards which uses the same offsets from start of memory as the common exynos5 settings. This fixes booting via bootz and PXE Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> --- include/configs/peach-pi.h | 8 ++++++++ include/configs/peach-pit.h | 8 ++++++++ 2 files changed, 16 insertions(+) diff --git a/include/configs/peach-pi.h b/include/configs/peach-pi.h index f04f061..e3cb09e 100644 --- a/include/configs/peach-pi.h +++ b/include/configs/peach-pi.h @@ -16,6 +16,14 @@ #define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE) #define CONFIG_SPI_BOOTING +#define MEM_LAYOUT_ENV_SETTINGS \ + "bootm_size=0x10000000\0" \ + "kernel_addr_r=0x22000000\0" \ + "fdt_addr_r=0x23000000\0" \ + "ramdisk_addr_r=0x23300000\0" \ + "scriptaddr=0x30000000\0" \ + "pxefile_addr_r=0x31000000\0" + #include <configs/exynos5420-common.h> #include <configs/exynos5-dt-common.h> diff --git a/include/configs/peach-pit.h b/include/configs/peach-pit.h index b5efbdc..3ee42ef 100644 --- a/include/configs/peach-pit.h +++ b/include/configs/peach-pit.h @@ -16,6 +16,14 @@ #define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE) #define CONFIG_SPI_BOOTING +#define MEM_LAYOUT_ENV_SETTINGS \ + "bootm_size=0x10000000\0" \ + "kernel_addr_r=0x22000000\0" \ + "fdt_addr_r=0x23000000\0" \ + "ramdisk_addr_r=0x23300000\0" \ + "scriptaddr=0x30000000\0" \ + "pxefile_addr_r=0x31000000\0" + #include <configs/exynos5420-common.h> #include <configs/exynos5-dt-common.h> -- 2.1.4 ^ permalink raw reply related [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH] config: peach: Correct memory layout environment settings 2015-03-12 21:33 [U-Boot] [PATCH] config: peach: Correct memory layout environment settings Sjoerd Simons @ 2015-03-23 21:04 ` Simon Glass 2015-03-24 7:46 ` Sjoerd Simons 2015-03-25 5:11 ` Tom Rini 0 siblings, 2 replies; 11+ messages in thread From: Simon Glass @ 2015-03-23 21:04 UTC (permalink / raw) To: u-boot Hi Sjoerd, On 12 March 2015 at 15:33, Sjoerd Simons <sjoerd.simons@collabora.co.uk> wrote: > The peach boards have their SDRAM start address at 0x20000000 instead of > 0x40000000 which seems common for all other exynos5 based boards. This > means the layout set in exynos5-common.h causes the kernel be loaded > more then 128MB (at 0x42000000) away from memory start which breaks > booting kernels with CONFIG_AUTO_ZRELADDR > > Define a custom MEM_LAYOUT_ENV_SETTINGS for both peach boards which uses > the same offsets from start of memory as the common exynos5 settings. > > This fixes booting via bootz and PXE > > Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> > --- > include/configs/peach-pi.h | 8 ++++++++ > include/configs/peach-pit.h | 8 ++++++++ > 2 files changed, 16 insertions(+) > > diff --git a/include/configs/peach-pi.h b/include/configs/peach-pi.h > index f04f061..e3cb09e 100644 > --- a/include/configs/peach-pi.h > +++ b/include/configs/peach-pi.h > @@ -16,6 +16,14 @@ > #define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE) > #define CONFIG_SPI_BOOTING > > +#define MEM_LAYOUT_ENV_SETTINGS \ > + "bootm_size=0x10000000\0" \ > + "kernel_addr_r=0x22000000\0" \ > + "fdt_addr_r=0x23000000\0" \ > + "ramdisk_addr_r=0x23300000\0" \ > + "scriptaddr=0x30000000\0" \ > + "pxefile_addr_r=0x31000000\0" > + > #include <configs/exynos5420-common.h> > #include <configs/exynos5-dt-common.h> > > diff --git a/include/configs/peach-pit.h b/include/configs/peach-pit.h > index b5efbdc..3ee42ef 100644 > --- a/include/configs/peach-pit.h > +++ b/include/configs/peach-pit.h > @@ -16,6 +16,14 @@ > #define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE) > #define CONFIG_SPI_BOOTING > > +#define MEM_LAYOUT_ENV_SETTINGS \ > + "bootm_size=0x10000000\0" \ > + "kernel_addr_r=0x22000000\0" \ > + "fdt_addr_r=0x23000000\0" \ > + "ramdisk_addr_r=0x23300000\0" \ > + "scriptaddr=0x30000000\0" \ > + "pxefile_addr_r=0x31000000\0" > + > #include <configs/exynos5420-common.h> > #include <configs/exynos5-dt-common.h> It would be great if we could have this in the device tree. I haven't merged this patch yet, but it goes some of the way: http://patchwork.ozlabs.org/patch/402714/ Regards, Simon ^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH] config: peach: Correct memory layout environment settings 2015-03-23 21:04 ` Simon Glass @ 2015-03-24 7:46 ` Sjoerd Simons 2015-03-25 3:09 ` Simon Glass 2015-03-25 5:11 ` Tom Rini 1 sibling, 1 reply; 11+ messages in thread From: Sjoerd Simons @ 2015-03-24 7:46 UTC (permalink / raw) To: u-boot Hey Simon, On Mon, 2015-03-23 at 15:04 -0600, Simon Glass wrote: > Hi Sjoerd, > > On 12 March 2015 at 15:33, Sjoerd Simons <sjoerd.simons@collabora.co.uk> wrote: > > The peach boards have their SDRAM start address at 0x20000000 instead of > > 0x40000000 which seems common for all other exynos5 based boards. This > > means the layout set in exynos5-common.h causes the kernel be loaded > > more then 128MB (at 0x42000000) away from memory start which breaks > > booting kernels with CONFIG_AUTO_ZRELADDR > > > > Define a custom MEM_LAYOUT_ENV_SETTINGS for both peach boards which uses > > the same offsets from start of memory as the common exynos5 settings. > > > > This fixes booting via bootz and PXE <snip> > It would be great if we could have this in the device tree. > > I haven't merged this patch yet, but it goes some of the way: > > http://patchwork.ozlabs.org/patch/402714/ I think it would be awesome to have this via device tree as well as that would be another step closer to allowing one u-boot binary for a group of boards. However, that's clearly much more work. So for the short term (and ideally the coming release) i'd quite prefer this minimal change to go in to unbreak bootz and PXE on these boards. -- Sjoerd Simons <sjoerd.simons@collabora.co.uk> Collabora Ltd. ^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH] config: peach: Correct memory layout environment settings 2015-03-24 7:46 ` Sjoerd Simons @ 2015-03-25 3:09 ` Simon Glass 0 siblings, 0 replies; 11+ messages in thread From: Simon Glass @ 2015-03-25 3:09 UTC (permalink / raw) To: u-boot Hi Sjoerd, On 24 March 2015 at 01:46, Sjoerd Simons <sjoerd.simons@collabora.co.uk> wrote: > > Hey Simon, > > On Mon, 2015-03-23 at 15:04 -0600, Simon Glass wrote: > > Hi Sjoerd, > > > > On 12 March 2015 at 15:33, Sjoerd Simons <sjoerd.simons@collabora.co.uk> wrote: > > > The peach boards have their SDRAM start address at 0x20000000 instead of > > > 0x40000000 which seems common for all other exynos5 based boards. This > > > means the layout set in exynos5-common.h causes the kernel be loaded > > > more then 128MB (at 0x42000000) away from memory start which breaks > > > booting kernels with CONFIG_AUTO_ZRELADDR > > > > > > Define a custom MEM_LAYOUT_ENV_SETTINGS for both peach boards which uses > > > the same offsets from start of memory as the common exynos5 settings. > > > > > > This fixes booting via bootz and PXE > > <snip> > > > It would be great if we could have this in the device tree. > > > > I haven't merged this patch yet, but it goes some of the way: > > > > http://patchwork.ozlabs.org/patch/402714/ > > I think it would be awesome to have this via device tree as well as that > would be another step closer to allowing one u-boot binary for a group > of boards. However, that's clearly much more work. So for the short term > (and ideally the coming release) i'd quite prefer this minimal change > to go in to unbreak bootz and PXE on these boards. OK. Reviewed-by: Simon Glass <sjg@chromium.org> Who is going to apply this? Regards, Simon ^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH] config: peach: Correct memory layout environment settings 2015-03-23 21:04 ` Simon Glass 2015-03-24 7:46 ` Sjoerd Simons @ 2015-03-25 5:11 ` Tom Rini 2015-03-25 8:32 ` Sjoerd Simons 1 sibling, 1 reply; 11+ messages in thread From: Tom Rini @ 2015-03-25 5:11 UTC (permalink / raw) To: u-boot On Mon, Mar 23, 2015 at 03:04:48PM -0600, Simon Glass wrote: > Hi Sjoerd, > > On 12 March 2015 at 15:33, Sjoerd Simons <sjoerd.simons@collabora.co.uk> wrote: > > The peach boards have their SDRAM start address at 0x20000000 instead of > > 0x40000000 which seems common for all other exynos5 based boards. This > > means the layout set in exynos5-common.h causes the kernel be loaded > > more then 128MB (at 0x42000000) away from memory start which breaks > > booting kernels with CONFIG_AUTO_ZRELADDR > > > > Define a custom MEM_LAYOUT_ENV_SETTINGS for both peach boards which uses > > the same offsets from start of memory as the common exynos5 settings. > > > > This fixes booting via bootz and PXE > > > > Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> > > --- > > include/configs/peach-pi.h | 8 ++++++++ > > include/configs/peach-pit.h | 8 ++++++++ > > 2 files changed, 16 insertions(+) > > > > diff --git a/include/configs/peach-pi.h b/include/configs/peach-pi.h > > index f04f061..e3cb09e 100644 > > --- a/include/configs/peach-pi.h > > +++ b/include/configs/peach-pi.h > > @@ -16,6 +16,14 @@ > > #define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE) > > #define CONFIG_SPI_BOOTING > > > > +#define MEM_LAYOUT_ENV_SETTINGS \ > > + "bootm_size=0x10000000\0" \ > > + "kernel_addr_r=0x22000000\0" \ > > + "fdt_addr_r=0x23000000\0" \ > > + "ramdisk_addr_r=0x23300000\0" \ > > + "scriptaddr=0x30000000\0" \ > > + "pxefile_addr_r=0x31000000\0" > > + > > #include <configs/exynos5420-common.h> > > #include <configs/exynos5-dt-common.h> > > > > diff --git a/include/configs/peach-pit.h b/include/configs/peach-pit.h > > index b5efbdc..3ee42ef 100644 > > --- a/include/configs/peach-pit.h > > +++ b/include/configs/peach-pit.h > > @@ -16,6 +16,14 @@ > > #define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE) > > #define CONFIG_SPI_BOOTING > > > > +#define MEM_LAYOUT_ENV_SETTINGS \ > > + "bootm_size=0x10000000\0" \ > > + "kernel_addr_r=0x22000000\0" \ > > + "fdt_addr_r=0x23000000\0" \ > > + "ramdisk_addr_r=0x23300000\0" \ > > + "scriptaddr=0x30000000\0" \ > > + "pxefile_addr_r=0x31000000\0" > > + > > #include <configs/exynos5420-common.h> > > #include <configs/exynos5-dt-common.h> > > It would be great if we could have this in the device tree. I understand what you're thinking but this is environment. And really this is not board specific, this is SoC family specific which is why the similar part for TI stuff is in ti_armv7_common.h :) -- Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20150325/7e529259/attachment.sig> ^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH] config: peach: Correct memory layout environment settings 2015-03-25 5:11 ` Tom Rini @ 2015-03-25 8:32 ` Sjoerd Simons 2015-03-25 16:58 ` Tom Rini 0 siblings, 1 reply; 11+ messages in thread From: Sjoerd Simons @ 2015-03-25 8:32 UTC (permalink / raw) To: u-boot On Wed, 2015-03-25 at 01:11 -0400, Tom Rini wrote: > On Mon, Mar 23, 2015 at 03:04:48PM -0600, Simon Glass wrote: > > Hi Sjoerd, > > > > On 12 March 2015 at 15:33, Sjoerd Simons <sjoerd.simons@collabora.co.uk> wrote: > > > The peach boards have their SDRAM start address at 0x20000000 instead of > > > 0x40000000 which seems common for all other exynos5 based boards. This > > > means the layout set in exynos5-common.h causes the kernel be loaded > > > more then 128MB (at 0x42000000) away from memory start which breaks > > > booting kernels with CONFIG_AUTO_ZRELADDR > > > > > > Define a custom MEM_LAYOUT_ENV_SETTINGS for both peach boards which uses > > > the same offsets from start of memory as the common exynos5 settings. > > > > > > This fixes booting via bootz and PXE > > > > > > Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> > > > --- > > > include/configs/peach-pi.h | 8 ++++++++ > > > include/configs/peach-pit.h | 8 ++++++++ > > > 2 files changed, 16 insertions(+) > > > > > > diff --git a/include/configs/peach-pi.h b/include/configs/peach-pi.h > > > index f04f061..e3cb09e 100644 > > > --- a/include/configs/peach-pi.h > > > +++ b/include/configs/peach-pi.h > > > @@ -16,6 +16,14 @@ > > > #define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE) > > > #define CONFIG_SPI_BOOTING > > > > > > +#define MEM_LAYOUT_ENV_SETTINGS \ > > > + "bootm_size=0x10000000\0" \ > > > + "kernel_addr_r=0x22000000\0" \ > > > + "fdt_addr_r=0x23000000\0" \ > > > + "ramdisk_addr_r=0x23300000\0" \ > > > + "scriptaddr=0x30000000\0" \ > > > + "pxefile_addr_r=0x31000000\0" > > > + > > > #include <configs/exynos5420-common.h> > > > #include <configs/exynos5-dt-common.h> > > > > > > diff --git a/include/configs/peach-pit.h b/include/configs/peach-pit.h > > > index b5efbdc..3ee42ef 100644 > > > --- a/include/configs/peach-pit.h > > > +++ b/include/configs/peach-pit.h > > > @@ -16,6 +16,14 @@ > > > #define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE) > > > #define CONFIG_SPI_BOOTING > > > > > > +#define MEM_LAYOUT_ENV_SETTINGS \ > > > + "bootm_size=0x10000000\0" \ > > > + "kernel_addr_r=0x22000000\0" \ > > > + "fdt_addr_r=0x23000000\0" \ > > > + "ramdisk_addr_r=0x23300000\0" \ > > > + "scriptaddr=0x30000000\0" \ > > > + "pxefile_addr_r=0x31000000\0" > > > + > > > #include <configs/exynos5420-common.h> > > > #include <configs/exynos5-dt-common.h> > > > > It would be great if we could have this in the device tree. > > I understand what you're thinking but this is environment. And really > this is not board specific, this is SoC family specific which is why the > similar part for TI stuff is in ti_armv7_common.h :) Exynos 5 has the same in exynos5-common.h, however for whatever reason the peach pi/pit boards are different then other exynos board supported by u-boot thusfar. So in this case, this information _is_ board specific not platform specific. But even in case of including it in device tree, a default/common setting could go into the platforms dtsi with board-specific overrides as needed. One thing i have wondered though, looking at the various boards specifying the various memory layour addresses. They all end up being relatively similar offset to the base memory address, which makes me think it may be possible to calculate these values in the initialisation code rather then having to hardcode it in the environment. However, even if that's a sensible thing, something for later :) -- Sjoerd Simons <sjoerd.simons@collabora.co.uk> Collabora Ltd. ^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH] config: peach: Correct memory layout environment settings 2015-03-25 8:32 ` Sjoerd Simons @ 2015-03-25 16:58 ` Tom Rini 2015-03-25 19:54 ` Sjoerd Simons 0 siblings, 1 reply; 11+ messages in thread From: Tom Rini @ 2015-03-25 16:58 UTC (permalink / raw) To: u-boot On Wed, Mar 25, 2015 at 09:32:45AM +0100, Sjoerd Simons wrote: > On Wed, 2015-03-25 at 01:11 -0400, Tom Rini wrote: > > On Mon, Mar 23, 2015 at 03:04:48PM -0600, Simon Glass wrote: > > > Hi Sjoerd, > > > > > > On 12 March 2015 at 15:33, Sjoerd Simons <sjoerd.simons@collabora.co.uk> wrote: > > > > The peach boards have their SDRAM start address at 0x20000000 instead of > > > > 0x40000000 which seems common for all other exynos5 based boards. This > > > > means the layout set in exynos5-common.h causes the kernel be loaded > > > > more then 128MB (at 0x42000000) away from memory start which breaks > > > > booting kernels with CONFIG_AUTO_ZRELADDR > > > > > > > > Define a custom MEM_LAYOUT_ENV_SETTINGS for both peach boards which uses > > > > the same offsets from start of memory as the common exynos5 settings. > > > > > > > > This fixes booting via bootz and PXE > > > > > > > > Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> > > > > --- > > > > include/configs/peach-pi.h | 8 ++++++++ > > > > include/configs/peach-pit.h | 8 ++++++++ > > > > 2 files changed, 16 insertions(+) > > > > > > > > diff --git a/include/configs/peach-pi.h b/include/configs/peach-pi.h > > > > index f04f061..e3cb09e 100644 > > > > --- a/include/configs/peach-pi.h > > > > +++ b/include/configs/peach-pi.h > > > > @@ -16,6 +16,14 @@ > > > > #define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE) > > > > #define CONFIG_SPI_BOOTING > > > > > > > > +#define MEM_LAYOUT_ENV_SETTINGS \ > > > > + "bootm_size=0x10000000\0" \ > > > > + "kernel_addr_r=0x22000000\0" \ > > > > + "fdt_addr_r=0x23000000\0" \ > > > > + "ramdisk_addr_r=0x23300000\0" \ > > > > + "scriptaddr=0x30000000\0" \ > > > > + "pxefile_addr_r=0x31000000\0" > > > > + > > > > #include <configs/exynos5420-common.h> > > > > #include <configs/exynos5-dt-common.h> > > > > > > > > diff --git a/include/configs/peach-pit.h b/include/configs/peach-pit.h > > > > index b5efbdc..3ee42ef 100644 > > > > --- a/include/configs/peach-pit.h > > > > +++ b/include/configs/peach-pit.h > > > > @@ -16,6 +16,14 @@ > > > > #define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE) > > > > #define CONFIG_SPI_BOOTING > > > > > > > > +#define MEM_LAYOUT_ENV_SETTINGS \ > > > > + "bootm_size=0x10000000\0" \ > > > > + "kernel_addr_r=0x22000000\0" \ > > > > + "fdt_addr_r=0x23000000\0" \ > > > > + "ramdisk_addr_r=0x23300000\0" \ > > > > + "scriptaddr=0x30000000\0" \ > > > > + "pxefile_addr_r=0x31000000\0" > > > > + > > > > #include <configs/exynos5420-common.h> > > > > #include <configs/exynos5-dt-common.h> > > > > > > It would be great if we could have this in the device tree. > > > > I understand what you're thinking but this is environment. And really > > this is not board specific, this is SoC family specific which is why the > > similar part for TI stuff is in ti_armv7_common.h :) > > Exynos 5 has the same in exynos5-common.h, however for whatever reason > the peach pi/pit boards are different then other exynos board supported > by u-boot thusfar. So in this case, this information _is_ board specific > not platform specific. Oh I missed that early on, sorry. But... Why not change things around a bit to enable CONFIG_CMD_SETEXPR and then have MEM_LAYOUT_ENV_SETTINGS just set the exynos5_ddr_base and then setexpr kernel_addr_r $exynos5_ddr_base + 0x2000000 and similar in the generic part. > But even in case of including it in device tree, a default/common > setting could go into the platforms dtsi with board-specific overrides > as needed. > > One thing i have wondered though, looking at the various boards > specifying the various memory layour addresses. They all end up being > relatively similar offset to the base memory address, which makes me > think it may be possible to calculate these values in the initialisation > code rather then having to hardcode it in the environment. However, even > if that's a sensible thing, something for later :) ... Yes, we should then take what I just did above and make it even further wide-spread among boards where we have more than ~512MB DDR or so :) -- Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20150325/499ed3a6/attachment.sig> ^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH] config: peach: Correct memory layout environment settings 2015-03-25 16:58 ` Tom Rini @ 2015-03-25 19:54 ` Sjoerd Simons 2015-03-25 20:49 ` Tom Rini 0 siblings, 1 reply; 11+ messages in thread From: Sjoerd Simons @ 2015-03-25 19:54 UTC (permalink / raw) To: u-boot On Wed, 2015-03-25 at 12:58 -0400, Tom Rini wrote: > On Wed, Mar 25, 2015 at 09:32:45AM +0100, Sjoerd Simons wrote: > > On Wed, 2015-03-25 at 01:11 -0400, Tom Rini wrote: > > > On Mon, Mar 23, 2015 at 03:04:48PM -0600, Simon Glass wrote: > > > > Hi Sjoerd, > > > > > > > > On 12 March 2015 at 15:33, Sjoerd Simons <sjoerd.simons@collabora.co.uk> wrote: > > > > > The peach boards have their SDRAM start address at 0x20000000 instead of > > > > > 0x40000000 which seems common for all other exynos5 based boards. This > > > > > means the layout set in exynos5-common.h causes the kernel be loaded > > > > > more then 128MB (at 0x42000000) away from memory start which breaks > > > > > booting kernels with CONFIG_AUTO_ZRELADDR > > > > > > > > > > Define a custom MEM_LAYOUT_ENV_SETTINGS for both peach boards which uses > > > > > the same offsets from start of memory as the common exynos5 settings. > > > > > > > > > > This fixes booting via bootz and PXE > > > > > > > > > > Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> > > > > > --- > > > > > include/configs/peach-pi.h | 8 ++++++++ > > > > > include/configs/peach-pit.h | 8 ++++++++ > > > > > 2 files changed, 16 insertions(+) > > > > > > > > > > diff --git a/include/configs/peach-pi.h b/include/configs/peach-pi.h > > > > > index f04f061..e3cb09e 100644 > > > > > --- a/include/configs/peach-pi.h > > > > > +++ b/include/configs/peach-pi.h > > > > > @@ -16,6 +16,14 @@ > > > > > #define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE) > > > > > #define CONFIG_SPI_BOOTING > > > > > > > > > > +#define MEM_LAYOUT_ENV_SETTINGS \ > > > > > + "bootm_size=0x10000000\0" \ > > > > > + "kernel_addr_r=0x22000000\0" \ > > > > > + "fdt_addr_r=0x23000000\0" \ > > > > > + "ramdisk_addr_r=0x23300000\0" \ > > > > > + "scriptaddr=0x30000000\0" \ > > > > > + "pxefile_addr_r=0x31000000\0" > > > > > + > > > > > #include <configs/exynos5420-common.h> > > > > > #include <configs/exynos5-dt-common.h> > > > > > > > > > > diff --git a/include/configs/peach-pit.h b/include/configs/peach-pit.h > > > > > index b5efbdc..3ee42ef 100644 > > > > > --- a/include/configs/peach-pit.h > > > > > +++ b/include/configs/peach-pit.h > > > > > @@ -16,6 +16,14 @@ > > > > > #define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE) > > > > > #define CONFIG_SPI_BOOTING > > > > > > > > > > +#define MEM_LAYOUT_ENV_SETTINGS \ > > > > > + "bootm_size=0x10000000\0" \ > > > > > + "kernel_addr_r=0x22000000\0" \ > > > > > + "fdt_addr_r=0x23000000\0" \ > > > > > + "ramdisk_addr_r=0x23300000\0" \ > > > > > + "scriptaddr=0x30000000\0" \ > > > > > + "pxefile_addr_r=0x31000000\0" > > > > > + > > > > > #include <configs/exynos5420-common.h> > > > > > #include <configs/exynos5-dt-common.h> > > > > > > > > It would be great if we could have this in the device tree. > > > > > > I understand what you're thinking but this is environment. And really > > > this is not board specific, this is SoC family specific which is why the > > > similar part for TI stuff is in ti_armv7_common.h :) > > > > Exynos 5 has the same in exynos5-common.h, however for whatever reason > > the peach pi/pit boards are different then other exynos board supported > > by u-boot thusfar. So in this case, this information _is_ board specific > > not platform specific. > > Oh I missed that early on, sorry. But... > > Why not change things around a bit to enable CONFIG_CMD_SETEXPR and then > have MEM_LAYOUT_ENV_SETTINGS just set the exynos5_ddr_base and then > setexpr kernel_addr_r $exynos5_ddr_base + 0x2000000 > and similar in the generic part. Partially because i didn't know the setexpr command and partially because i wanted a minimally disruptive patch that can hopefully still make it for 2015.4. I think doing the above would also require tweaking the distro_boot_cmd code to integrate it nicely. > > But even in case of including it in device tree, a default/common > > setting could go into the platforms dtsi with board-specific overrides > > as needed. > > > > One thing i have wondered though, looking at the various boards > > specifying the various memory layour addresses. They all end up being > > relatively similar offset to the base memory address, which makes me > > think it may be possible to calculate these values in the initialisation > > code rather then having to hardcode it in the environment. However, even > > if that's a sensible thing, something for later :) > > ... Yes, we should then take what I just did above and make it even > further wide-spread among boards where we have more than ~512MB DDR or > so :) Sounds like a plan. -- Sjoerd Simons <sjoerd.simons@collabora.co.uk> Collabora Ltd. ^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH] config: peach: Correct memory layout environment settings 2015-03-25 19:54 ` Sjoerd Simons @ 2015-03-25 20:49 ` Tom Rini 2015-03-26 10:11 ` Sjoerd Simons 0 siblings, 1 reply; 11+ messages in thread From: Tom Rini @ 2015-03-25 20:49 UTC (permalink / raw) To: u-boot On Wed, Mar 25, 2015 at 08:54:16PM +0100, Sjoerd Simons wrote: > On Wed, 2015-03-25 at 12:58 -0400, Tom Rini wrote: > > On Wed, Mar 25, 2015 at 09:32:45AM +0100, Sjoerd Simons wrote: > > > On Wed, 2015-03-25 at 01:11 -0400, Tom Rini wrote: > > > > On Mon, Mar 23, 2015 at 03:04:48PM -0600, Simon Glass wrote: > > > > > Hi Sjoerd, > > > > > > > > > > On 12 March 2015 at 15:33, Sjoerd Simons <sjoerd.simons@collabora.co.uk> wrote: > > > > > > The peach boards have their SDRAM start address at 0x20000000 instead of > > > > > > 0x40000000 which seems common for all other exynos5 based boards. This > > > > > > means the layout set in exynos5-common.h causes the kernel be loaded > > > > > > more then 128MB (at 0x42000000) away from memory start which breaks > > > > > > booting kernels with CONFIG_AUTO_ZRELADDR > > > > > > > > > > > > Define a custom MEM_LAYOUT_ENV_SETTINGS for both peach boards which uses > > > > > > the same offsets from start of memory as the common exynos5 settings. > > > > > > > > > > > > This fixes booting via bootz and PXE > > > > > > > > > > > > Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> > > > > > > --- > > > > > > include/configs/peach-pi.h | 8 ++++++++ > > > > > > include/configs/peach-pit.h | 8 ++++++++ > > > > > > 2 files changed, 16 insertions(+) > > > > > > > > > > > > diff --git a/include/configs/peach-pi.h b/include/configs/peach-pi.h > > > > > > index f04f061..e3cb09e 100644 > > > > > > --- a/include/configs/peach-pi.h > > > > > > +++ b/include/configs/peach-pi.h > > > > > > @@ -16,6 +16,14 @@ > > > > > > #define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE) > > > > > > #define CONFIG_SPI_BOOTING > > > > > > > > > > > > +#define MEM_LAYOUT_ENV_SETTINGS \ > > > > > > + "bootm_size=0x10000000\0" \ > > > > > > + "kernel_addr_r=0x22000000\0" \ > > > > > > + "fdt_addr_r=0x23000000\0" \ > > > > > > + "ramdisk_addr_r=0x23300000\0" \ > > > > > > + "scriptaddr=0x30000000\0" \ > > > > > > + "pxefile_addr_r=0x31000000\0" > > > > > > + > > > > > > #include <configs/exynos5420-common.h> > > > > > > #include <configs/exynos5-dt-common.h> > > > > > > > > > > > > diff --git a/include/configs/peach-pit.h b/include/configs/peach-pit.h > > > > > > index b5efbdc..3ee42ef 100644 > > > > > > --- a/include/configs/peach-pit.h > > > > > > +++ b/include/configs/peach-pit.h > > > > > > @@ -16,6 +16,14 @@ > > > > > > #define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE) > > > > > > #define CONFIG_SPI_BOOTING > > > > > > > > > > > > +#define MEM_LAYOUT_ENV_SETTINGS \ > > > > > > + "bootm_size=0x10000000\0" \ > > > > > > + "kernel_addr_r=0x22000000\0" \ > > > > > > + "fdt_addr_r=0x23000000\0" \ > > > > > > + "ramdisk_addr_r=0x23300000\0" \ > > > > > > + "scriptaddr=0x30000000\0" \ > > > > > > + "pxefile_addr_r=0x31000000\0" > > > > > > + > > > > > > #include <configs/exynos5420-common.h> > > > > > > #include <configs/exynos5-dt-common.h> > > > > > > > > > > It would be great if we could have this in the device tree. > > > > > > > > I understand what you're thinking but this is environment. And really > > > > this is not board specific, this is SoC family specific which is why the > > > > similar part for TI stuff is in ti_armv7_common.h :) > > > > > > Exynos 5 has the same in exynos5-common.h, however for whatever reason > > > the peach pi/pit boards are different then other exynos board supported > > > by u-boot thusfar. So in this case, this information _is_ board specific > > > not platform specific. > > > > Oh I missed that early on, sorry. But... > > > > Why not change things around a bit to enable CONFIG_CMD_SETEXPR and then > > have MEM_LAYOUT_ENV_SETTINGS just set the exynos5_ddr_base and then > > setexpr kernel_addr_r $exynos5_ddr_base + 0x2000000 > > and similar in the generic part. > > Partially because i didn't know the setexpr command and partially > because i wanted a minimally disruptive patch that can hopefully still > make it for 2015.4. For the first part I forgot it existed until this morning so that's OK :) > I think doing the above would also require tweaking the distro_boot_cmd > code to integrate it nicely. I'm agreeable to taking this now to fix things if we promise to clean it up ASAP after the release (since we can do that without breaking the visible portion I think). -- Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20150325/e9027565/attachment.sig> ^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH] config: peach: Correct memory layout environment settings 2015-03-25 20:49 ` Tom Rini @ 2015-03-26 10:11 ` Sjoerd Simons 2015-04-06 6:33 ` Minkyu Kang 0 siblings, 1 reply; 11+ messages in thread From: Sjoerd Simons @ 2015-03-26 10:11 UTC (permalink / raw) To: u-boot On Wed, 2015-03-25 at 16:49 -0400, Tom Rini wrote: > On Wed, Mar 25, 2015 at 08:54:16PM +0100, Sjoerd Simons wrote: > > On Wed, 2015-03-25 at 12:58 -0400, Tom Rini wrote: > > > On Wed, Mar 25, 2015 at 09:32:45AM +0100, Sjoerd Simons wrote: > > > > On Wed, 2015-03-25 at 01:11 -0400, Tom Rini wrote: > > > > > On Mon, Mar 23, 2015 at 03:04:48PM -0600, Simon Glass wrote: > > > > > > Hi Sjoerd, > > > > > > > > > > > > On 12 March 2015 at 15:33, Sjoerd Simons <sjoerd.simons@collabora.co.uk> wrote: > > > > > > > The peach boards have their SDRAM start address at 0x20000000 instead of > > > > > > > 0x40000000 which seems common for all other exynos5 based boards. This > > > > > > > means the layout set in exynos5-common.h causes the kernel be loaded > > > > > > > more then 128MB (at 0x42000000) away from memory start which breaks > > > > > > > booting kernels with CONFIG_AUTO_ZRELADDR > > > > > > > > > > > > > > Define a custom MEM_LAYOUT_ENV_SETTINGS for both peach boards which uses > > > > > > > the same offsets from start of memory as the common exynos5 settings. > > > > > > > > > > > > > > This fixes booting via bootz and PXE > > > > > > > > > > > > > > Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> > > > > > > > --- > > > > > > > include/configs/peach-pi.h | 8 ++++++++ > > > > > > > include/configs/peach-pit.h | 8 ++++++++ > > > > > > > 2 files changed, 16 insertions(+) > > > > > > > > > > > > > > diff --git a/include/configs/peach-pi.h b/include/configs/peach-pi.h > > > > > > > index f04f061..e3cb09e 100644 > > > > > > > --- a/include/configs/peach-pi.h > > > > > > > +++ b/include/configs/peach-pi.h > > > > > > > @@ -16,6 +16,14 @@ > > > > > > > #define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE) > > > > > > > #define CONFIG_SPI_BOOTING > > > > > > > > > > > > > > +#define MEM_LAYOUT_ENV_SETTINGS \ > > > > > > > + "bootm_size=0x10000000\0" \ > > > > > > > + "kernel_addr_r=0x22000000\0" \ > > > > > > > + "fdt_addr_r=0x23000000\0" \ > > > > > > > + "ramdisk_addr_r=0x23300000\0" \ > > > > > > > + "scriptaddr=0x30000000\0" \ > > > > > > > + "pxefile_addr_r=0x31000000\0" > > > > > > > + > > > > > > > #include <configs/exynos5420-common.h> > > > > > > > #include <configs/exynos5-dt-common.h> > > > > > > > > > > > > > > diff --git a/include/configs/peach-pit.h b/include/configs/peach-pit.h > > > > > > > index b5efbdc..3ee42ef 100644 > > > > > > > --- a/include/configs/peach-pit.h > > > > > > > +++ b/include/configs/peach-pit.h > > > > > > > @@ -16,6 +16,14 @@ > > > > > > > #define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE) > > > > > > > #define CONFIG_SPI_BOOTING > > > > > > > > > > > > > > +#define MEM_LAYOUT_ENV_SETTINGS \ > > > > > > > + "bootm_size=0x10000000\0" \ > > > > > > > + "kernel_addr_r=0x22000000\0" \ > > > > > > > + "fdt_addr_r=0x23000000\0" \ > > > > > > > + "ramdisk_addr_r=0x23300000\0" \ > > > > > > > + "scriptaddr=0x30000000\0" \ > > > > > > > + "pxefile_addr_r=0x31000000\0" > > > > > > > + > > > > > > > #include <configs/exynos5420-common.h> > > > > > > > #include <configs/exynos5-dt-common.h> > > > > > > > > > > > > It would be great if we could have this in the device tree. > > > > > > > > > > I understand what you're thinking but this is environment. And really > > > > > this is not board specific, this is SoC family specific which is why the > > > > > similar part for TI stuff is in ti_armv7_common.h :) > > > > > > > > Exynos 5 has the same in exynos5-common.h, however for whatever reason > > > > the peach pi/pit boards are different then other exynos board supported > > > > by u-boot thusfar. So in this case, this information _is_ board specific > > > > not platform specific. > > > > > > Oh I missed that early on, sorry. But... > > > > > > Why not change things around a bit to enable CONFIG_CMD_SETEXPR and then > > > have MEM_LAYOUT_ENV_SETTINGS just set the exynos5_ddr_base and then > > > setexpr kernel_addr_r $exynos5_ddr_base + 0x2000000 > > > and similar in the generic part. > > > > Partially because i didn't know the setexpr command and partially > > because i wanted a minimally disruptive patch that can hopefully still > > make it for 2015.4. > > For the first part I forgot it existed until this morning so that's OK > :) Hah > > I think doing the above would also require tweaking the distro_boot_cmd > > code to integrate it nicely. > > I'm agreeable to taking this now to fix things if we promise to clean it > up ASAP after the release (since we can do that without breaking the > visible portion I think). I'm ok to prepare some patches for polishing this in the next few weeks as it peeked my interests. -- Sjoerd Simons <sjoerd.simons@collabora.co.uk> Collabora Ltd. ^ permalink raw reply [flat|nested] 11+ messages in thread
* [U-Boot] [PATCH] config: peach: Correct memory layout environment settings 2015-03-26 10:11 ` Sjoerd Simons @ 2015-04-06 6:33 ` Minkyu Kang 0 siblings, 0 replies; 11+ messages in thread From: Minkyu Kang @ 2015-04-06 6:33 UTC (permalink / raw) To: u-boot On 26/03/15 19:11, Sjoerd Simons wrote: > On Wed, 2015-03-25 at 16:49 -0400, Tom Rini wrote: >> On Wed, Mar 25, 2015 at 08:54:16PM +0100, Sjoerd Simons wrote: >>> On Wed, 2015-03-25 at 12:58 -0400, Tom Rini wrote: >>>> On Wed, Mar 25, 2015 at 09:32:45AM +0100, Sjoerd Simons wrote: >>>>> On Wed, 2015-03-25 at 01:11 -0400, Tom Rini wrote: >>>>>> On Mon, Mar 23, 2015 at 03:04:48PM -0600, Simon Glass wrote: >>>>>>> Hi Sjoerd, >>>>>>> >>>>>>> On 12 March 2015 at 15:33, Sjoerd Simons <sjoerd.simons@collabora.co.uk> wrote: >>>>>>>> The peach boards have their SDRAM start address at 0x20000000 instead of >>>>>>>> 0x40000000 which seems common for all other exynos5 based boards. This >>>>>>>> means the layout set in exynos5-common.h causes the kernel be loaded >>>>>>>> more then 128MB (at 0x42000000) away from memory start which breaks >>>>>>>> booting kernels with CONFIG_AUTO_ZRELADDR >>>>>>>> >>>>>>>> Define a custom MEM_LAYOUT_ENV_SETTINGS for both peach boards which uses >>>>>>>> the same offsets from start of memory as the common exynos5 settings. >>>>>>>> >>>>>>>> This fixes booting via bootz and PXE >>>>>>>> >>>>>>>> Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> >>>>>>>> --- >>>>>>>> include/configs/peach-pi.h | 8 ++++++++ >>>>>>>> include/configs/peach-pit.h | 8 ++++++++ >>>>>>>> 2 files changed, 16 insertions(+) >>>>>>>> applied to u-boot-samsung. Thanks, Minkyu Kang. ^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2015-04-06 6:33 UTC | newest] Thread overview: 11+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2015-03-12 21:33 [U-Boot] [PATCH] config: peach: Correct memory layout environment settings Sjoerd Simons 2015-03-23 21:04 ` Simon Glass 2015-03-24 7:46 ` Sjoerd Simons 2015-03-25 3:09 ` Simon Glass 2015-03-25 5:11 ` Tom Rini 2015-03-25 8:32 ` Sjoerd Simons 2015-03-25 16:58 ` Tom Rini 2015-03-25 19:54 ` Sjoerd Simons 2015-03-25 20:49 ` Tom Rini 2015-03-26 10:11 ` Sjoerd Simons 2015-04-06 6:33 ` Minkyu Kang
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.