From: poma <pomidorabelisima@gmail.com>
To: Antti Palosaari <crope@iki.fi>,
linux-media <linux-media@vger.kernel.org>
Cc: Michael Krufky <mkrufky@linuxtv.org>,
Manu Abraham <abraham.manu@gmail.com>
Subject: Re: dvb_usb_af9015: command failed=1 _ kernel >= 4.1.x
Date: Wed, 13 May 2015 05:56:23 +0200 [thread overview]
Message-ID: <5552CB67.8070106@gmail.com> (raw)
In-Reply-To: <55520A08.1010605@iki.fi>
On 12.05.2015 16:11, Antti Palosaari wrote:
> On 05/11/2015 09:43 PM, poma wrote:
>> On 05/11/2015 12:25 AM, poma wrote:
>>> On 10.05.2015 12:38, poma wrote:
>>>> On 08.05.2015 12:59, poma wrote:
>>>>> On 08.05.2015 12:20, poma wrote:
>>>>>>
>>>>>> [ 0.000000] Linux version 4.0.2-200.fc21.x86_64 ...
>>>>>>
>>>>>> [ 0.870875] usb 1-2: new high-speed USB device number 2 using ehci-pci
>>>>>> [ 0.990286] usb 1-2: New USB device found, idVendor=15a4, idProduct=9016
>>>>>> [ 0.992575] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
>>>>>> [ 0.994859] usb 1-2: Product: DVB-T 2
>>>>>>
>>>>>> [ 1.001398] usb 1-2: Manufacturer: Afatech
>>>>>> [ 1.003555] usb 1-2: SerialNumber: 010101010600001
>>>>>> [ 1.009194] Afatech DVB-T 2: Fixing fullspeed to highspeed interval: 10 -> 7
>>>>>> [ 1.011694] input: Afatech DVB-T 2 as /devices/pci0000:00/0000:00:02.1/usb1/1-2/1-2:1.1/0003:15A4:9016.0001/input/input5
>>>>>> [ 1.066814] hid-generic 0003:15A4:9016.0001: input,hidraw0: USB HID v1.01 Keyboard [Afatech DVB-T 2] on usb-0000:00:02.1-2/input1
>>>>>>
>>>>>> [ 11.997119] usb 1-2: dvb_usb_v2: found a 'Afatech AF9015 reference design' in warm state
>>>>>> [ 12.206778] usb 1-2: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
>>>>>> [ 12.207412] DVB: registering new adapter (Afatech AF9015 reference design)
>>>>>>
>>>>>> [ 12.286137] i2c i2c-13: af9013: firmware version 5.1.0.0
>>>>>> [ 12.289121] usb 1-2: DVB: registering adapter 0 frontend 0 (Afatech AF9013)...
>>>>>> [ 12.343650] mxl5007t 13-00c0: creating new instance
>>>>>> [ 12.346003] mxl5007t_get_chip_id: unknown rev (3f)
>>>>>> [ 12.346156] mxl5007t_get_chip_id: MxL5007T detected @ 13-00c0
>>>>>> [ 12.350371] usb 1-2: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
>>>>>> [ 12.350649] DVB: registering new adapter (Afatech AF9015 reference design)
>>>>>> [ 12.553632] i2c i2c-13: af9013: found a 'Afatech AF9013' in warm state
>>>>>> [ 12.557256] i2c i2c-13: af9013: firmware version 5.1.0.0
>>>>>> [ 12.563779] usb 1-2: DVB: registering adapter 1 frontend 0 (Afatech AF9013)...
>>>>>> [ 12.564554] mxl5007t 13-00c0: attaching existing instance
>>>>>> [ 12.567004] usb 1-2: dvb_usb_af9015: command failed=1
>>>>>> [ 12.567555] mxl5007t_soft_reset: 521: failed!
>>>>>> [ 12.569745] mxl5007t_attach: error -121 on line 907
>>>>>> [ 12.571231] usbcore: registered new interface driver dvb_usb_af9015
>>>>>>
>>>>>>
>>>>>> $ lsdvb
>>>>>>
>>>>>> lsdvb: Simple utility to list PCI/PCIe DVB devices
>>>>>> Version: 0.0.4
>>>>>> Copyright (C) Manu Abraham
>>>>>> $
>>>>>>
>>>>>
>>>>>
>>>>> Afatech AF9015 reference design:
>>>>>
>>>>> 3.18.12-200.fc21.x86_64 - OK
>>>>>
>>>>> 3.19.7-200.fc21.x86_64 - KO
>>>>> 4.0.2-200.fc21.x86_64 - KO
>>>>> 4.1.0-0.rc2.git3.1.fc23.x86_64 - KO
>>>>>
>>>>>
>>>>> If you have a patch to test, shout loudly.
>>>>>
>>>>>
>>>>
>>>> Looks like the same bug:
>>>> AVerMedia HD Volar (A867) - Afatech AF9033
>>>> http://forum.sifteam.eu/sifbox-by-sif-team/125122-kernel-3-19-a867-xgaz-dove.html
>>>>
>>>> http://git.linuxtv.org/cgit.cgi/media_build.git - no positive effect.
>>>>
>>>>
>>>> Ho ho ho
>>>>
>>>
>>> It seems the 'lsdvb' is what made the device unusable after re/boot.
>>> Of course this applies to kernel >= 3.19.x
>>> The device has to be unplugged and after a minute or two plugged back to be usable again.
>>>
>>>
>>> $ lsdvb
>>>
>>> lsdvb: Simple utility to list PCI/PCIe DVB devices
>>> Version: 0.0.4
>>> Copyright (C) Manu Abraham
>>>
>>> usb (5:0 -868620712:32665) on PCI Domain:-874755276 Bus:32665 Device:2098 Function:0
>>> DEVICE:0 ADAPTER:0 FRONTEND:0 (Afatech AF9013)
>>> FE_OFDM Fmin=174MHz Fmax=862MHz
>>> DEVICE:0 ADAPTER:1 FRONTEND:0 (Afatech AF9013)
>>> FE_OFDM Fmin=174MHz Fmax=862MHz
>>>
>>> $ dmesg
>>> [ 80.332837] usb 2-2: dvb_usb_af9015: command failed=1
>>> [ 80.332857] i2c i2c-13: af9013: i2c wr failed=-5 reg=d607 len=1
>>> [ 80.337837] usb 2-2: dvb_usb_af9015: command failed=1
>>> [ 80.337848] mxl5007t_write_reg: 472: failed!
>>> [ 80.337853] mxl5007t_sleep: error -121 on line 709
>>> [ 80.338324] usb 2-2: dvb_usb_af9015: command failed=1
>>> [ 80.338328] mxl5007t_write_reg: 472: failed!
>>> [ 80.338332] mxl5007t_sleep: error -121 on line 711
>>>
>>>
>>>
>>
>>
>> Furthermore, it is sufficient to re/boot to the latest kernels,
>> and the device is K.O. again,
>>
>> e.g.
>> # modinfo -n mxl5007t
>> /lib/modules/4.1.0-0.rc3.git0.1.fc23.x86_64+debug/kernel/drivers/media/tuners/mxl5007t.ko.xz
>>
>> ...
>> [ 13.874536] i2c i2c-13: af9013: found a 'Afatech AF9013' in warm state
>> [ 13.878031] i2c i2c-13: af9013: firmware version 5.1.0.0
>> [ 13.884691] usb 1-2: DVB: registering adapter 1 frontend 0 (Afatech AF9013)...
>> [ 13.884942] mxl5007t 13-00c0: attaching existing instance
>> [ 13.887166] usb 1-2: dvb_usb_af9015: command failed=1
>> [ 13.887179] mxl5007t_soft_reset: 521: failed!
>> [ 13.888780] mxl5007t_attach: error -121 on line 907
>> [ 13.897808] usbcore: registered new interface driver dvb_usb_af9015
>> ...
>>
>> # ls -al /dev/dvb
>> ls: cannot access /dev/dvb: No such file or directory
>>
>>
>> Keep in mind, this time it has nothing to do with 'lsdvb',
>>
>> # lsdvb
>> -bash: /bin/lsdvb: Permission denied
>
> It is that commit which causes the problem:
> commit fe4860af002a4516dd878f7297b61e186c475b35
> [media] [PATH,1/2] mxl5007 move reset to attach
>
> ... but I am pretty sure actual root of cause something else. Likely
> your second tuner chip is on reset/powered off and due to that it does
> not answer. I have almost similar device which works (DigitalNow TinyTwin).
>
> Maybe I should try to test which are that tuner GPIO reset lines... but
> I am a bit lazy :/
>
> regards
> Antti
>
Is a beer keg enough as bribe? :)
Just do not say that you drink juice.
After the reverting of all changes
http://git.linuxtv.org/cgit.cgi/media_tree.git/log/drivers/media/tuners/mxl5007t.c
device now survives both, 'lsdvb' and rc kernels.
Besides, despite all this, this device is already not working at its full potential.
One of the tuners can withstand a few hours and then hangs.
After that, in the application e.g. vlc is needed to select the second tuner and so continue to use the device.
So this is actually a "single-seater" as Formula 1.
Vroom vroom!
mxl5007t.c | 28 +++++-----------------------
1 file changed, 5 insertions(+), 23 deletions(-)
--- a/drivers/media/tuners/mxl5007t.c 2015-05-13 04:50:18.362256795 +0200
+++ b/drivers/media/tuners/mxl5007t.c 2015-05-13 05:05:15.070996638 +0200
@@ -374,6 +374,7 @@
mxl5007t_set_if_freq_bits(state, cfg->if_freq_hz, cfg->invert_if);
mxl5007t_set_xtal_freq_bits(state, cfg->xtal_freq_hz);
+ set_reg_bits(state->tab_init, 0x04, 0x01, cfg->loop_thru_enable);
set_reg_bits(state->tab_init, 0x03, 0x08, cfg->clk_out_enable << 3);
set_reg_bits(state->tab_init, 0x03, 0x07, cfg->clk_out_amp);
@@ -530,6 +531,10 @@
struct reg_pair_t *init_regs;
int ret;
+ ret = mxl5007t_soft_reset(state);
+ if (mxl_fail(ret))
+ goto fail;
+
/* calculate initialization reg array */
init_regs = mxl5007t_calc_init_regs(state, mode);
@@ -896,29 +901,6 @@
break;
}
- if (fe->ops.i2c_gate_ctrl)
- fe->ops.i2c_gate_ctrl(fe, 1);
-
- ret = mxl5007t_soft_reset(state);
-
- if (fe->ops.i2c_gate_ctrl)
- fe->ops.i2c_gate_ctrl(fe, 0);
-
- if (mxl_fail(ret))
- goto fail;
-
- if (fe->ops.i2c_gate_ctrl)
- fe->ops.i2c_gate_ctrl(fe, 1);
-
- ret = mxl5007t_write_reg(state, 0x04,
- state->config->loop_thru_enable);
-
- if (fe->ops.i2c_gate_ctrl)
- fe->ops.i2c_gate_ctrl(fe, 0);
-
- if (mxl_fail(ret))
- goto fail;
-
fe->tuner_priv = state;
mutex_unlock(&mxl5007t_list_mutex);
$ modinfo mxl5007t
filename: /lib/modules/4.1.0-0.rc3.git1.1.fc23.x86_64/updates/mxl5007t.ko
version: 0.2
license: GPL
author: Michael Krufky <mkrufky@linuxtv.org>
description: MaxLinear MxL5007T Silicon IC tuner driver
srcversion: 72D27DB6EF6CEC612700FB9
depends:
intree: Y
vermagic: 4.1.0-0.rc3.git1.1.fc23.x86_64 SMP mod_unload
parm: debug:set debug level (int)
$ dmesg
[ 1.114202] usb 1-2: new high-speed USB device number 2 using ehci-pci
[ 1.235071] usb 1-2: New USB device found, idVendor=15a4, idProduct=9016
[ 1.237463] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.239831] usb 1-2: Product: DVB-T 2
[ 1.242163] usb 1-2: Manufacturer: Afatech
[ 1.244422] usb 1-2: SerialNumber: 010101010600001
[ 1.251607] Afatech DVB-T 2: Fixing fullspeed to highspeed interval: 10 -> 7
[ 1.254602] input: Afatech DVB-T 2 as /devices/pci0000:00/0000:00:02.1/usb1/1-2/1-2:1.1/0003:15A4:9016.0001/input/input5
[ 1.311052] hid-generic 0003:15A4:9016.0001: input,hidraw0: USB HID v1.01 Keyboard [Afatech DVB-T 2] on usb-0000:00:02.1-2/input1
[ 14.326420] usb 1-2: dvb_usb_v2: found a 'Afatech AF9015 reference design' in warm state
[ 14.563618] usb 1-2: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
[ 14.563854] DVB: registering new adapter (Afatech AF9015 reference design)
[ 14.622564] usb 1-2: DVB: registering adapter 0 frontend 0 (Afatech AF9013)...
[ 14.659556] mxl5007t: module verification failed: signature and/or required key missing - tainting kernel
[ 14.660903] mxl5007t 13-00c0: creating new instance
[ 14.663714] mxl5007t_get_chip_id: unknown rev (3f)
[ 14.663727] mxl5007t_get_chip_id: MxL5007T detected @ 13-00c0
[ 14.664450] usb 1-2: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
[ 14.664603] DVB: registering new adapter (Afatech AF9015 reference design)
[ 14.882505] usb 1-2: DVB: registering adapter 1 frontend 0 (Afatech AF9013)...
[ 14.883176] mxl5007t 13-00c0: attaching existing instance
[ 14.905227] input: Afatech AF9015 reference design as /devices/pci0000:00/0000:00:02.1/usb1/1-2/rc/rc0/input14
[ 14.907885] rc0: Afatech AF9015 reference design as /devices/pci0000:00/0000:00:02.1/usb1/1-2/rc/rc0
[ 14.907917] usb 1-2: dvb_usb_v2: schedule remote query interval to 500 msecs
[ 14.908170] usb 1-2: dvb_usb_v2: 'Afatech AF9015 reference design' successfully initialized and connected
[ 14.908490] usbcore: registered new interface driver dvb_usb_af9015
$ lsdvb
lsdvb: Simple utility to list PCI/PCIe DVB devices
Version: 0.0.4
Copyright (C) Manu Abraham
usb (5:0 -956221864:32726) on PCI Domain:-962356428 Bus:32726 Device:2098 Function:0
DEVICE:0 ADAPTER:0 FRONTEND:0 (Afatech AF9013)
FE_OFDM Fmin=174MHz Fmax=862MHz
DEVICE:0 ADAPTER:1 FRONTEND:0 (Afatech AF9013)
FE_OFDM Fmin=174MHz Fmax=862MHz
$ dmesg
[ 306.258474] usb 1-2: dvb_usb_af9015: command failed=1
[ 306.258500] i2c i2c-13: af9013: i2c wr failed=-5 reg=d607 len=1
[ 306.264805] usb 1-2: dvb_usb_af9015: command failed=1
[ 306.264819] mxl5007t_write_reg: 473: failed!
[ 306.264826] mxl5007t_sleep: error -121 on line 714
[ 306.265298] usb 1-2: dvb_usb_af9015: command failed=1
[ 306.265306] mxl5007t_write_reg: 473: failed!
[ 306.265309] mxl5007t_sleep: error -121 on line 716
next prev parent reply other threads:[~2015-05-13 3:56 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-05-08 10:20 dvb_usb_af9015: command failed=1 - stable: 4.0.2 poma
2015-05-08 10:59 ` poma
2015-05-10 10:38 ` dvb_usb_af9015: command failed=1 >= 3.19.x poma
2015-05-10 22:25 ` dvb_usb_af9015: command failed=1 _ lsdvb " poma
2015-05-11 18:43 ` dvb_usb_af9015: command failed=1 _ kernel >= 4.1.x poma
2015-05-12 14:11 ` Antti Palosaari
2015-05-13 3:56 ` poma [this message]
2015-05-16 23:07 ` Antti Palosaari
2015-05-18 19:15 ` poma
2015-05-21 21:23 ` poma
2015-05-26 12:24 ` poma
2015-07-02 23:02 ` poma
-- strict thread matches above, loose matches on Subject: below --
2015-07-06 20:17 Jose Alberto Reguero
2015-07-07 8:48 ` poma
2015-07-13 9:48 ` poma
2015-07-31 15:03 ` poma
[not found] ` <CAAZRmGym49dG6Jj-ZeKZmy0rgr4ozph7-ggjLoWtGOvT1m4oBA@mail.gmail.com>
2015-08-10 21:46 ` poma
2015-08-10 22:40 ` Antti Palosaari
2015-08-12 23:52 ` poma
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5552CB67.8070106@gmail.com \
--to=pomidorabelisima@gmail.com \
--cc=abraham.manu@gmail.com \
--cc=crope@iki.fi \
--cc=linux-media@vger.kernel.org \
--cc=mkrufky@linuxtv.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.