* [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
@ 2015-05-13 14:13 ` Simon Glass
0 siblings, 0 replies; 20+ messages in thread
From: Simon Glass @ 2015-05-13 14:13 UTC (permalink / raw)
To: LKML
Cc: Stephen Warren, Stephen Warren, Simon Glass, Russell King,
Thierry Reding, devicetree, Kumar Gala, Ian Campbell, Rob Herring,
Pawel Moll, linux-tegra, Mark Rutland, Alexandre Courbot,
linux-arm-kernel
Regenerate the pinmux from the latest tegra-pinmux-scripts.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
arch/arm/boot/dts/tegra124-nyan-big.dts | 22 +++++++++++-----------
arch/arm/boot/dts/tegra124-nyan-blaze.dts | 30 +++++++++++++++---------------
2 files changed, 26 insertions(+), 26 deletions(-)
diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts b/arch/arm/boot/dts/tegra124-nyan-big.dts
index 2d21253..0eb2b0f 100644
--- a/arch/arm/boot/dts/tegra124-nyan-big.dts
+++ b/arch/arm/boot/dts/tegra124-nyan-big.dts
@@ -30,7 +30,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinmux_default>;
- pinmux_default: common {
+ state_default: pinmux {
clk_32k_out_pa0 {
nvidia,pins = "clk_32k_out_pa0";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
@@ -1098,19 +1098,19 @@
};
cam_i2c_scl_pbb1 {
nvidia,pins = "cam_i2c_scl_pbb1";
- nvidia,function = "rsvd3";
- nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
- nvidia,tristate = <TEGRA_PIN_ENABLE>;
- nvidia,enable-input = <TEGRA_PIN_DISABLE>;
- nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ nvidia,function = "i2c3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
};
cam_i2c_sda_pbb2 {
nvidia,pins = "cam_i2c_sda_pbb2";
- nvidia,function = "rsvd3";
- nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
- nvidia,tristate = <TEGRA_PIN_ENABLE>;
- nvidia,enable-input = <TEGRA_PIN_DISABLE>;
- nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ nvidia,function = "i2c3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
};
pbb3 {
nvidia,pins = "pbb3";
diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
index 0d30c51..1fc0da9 100644
--- a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
+++ b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
@@ -26,7 +26,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinmux_default>;
- pinmux_default: common {
+ state_default: pinmux {
clk_32k_out_pa0 {
nvidia,pins = "clk_32k_out_pa0";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
@@ -437,18 +437,18 @@
usb_vbus_en0_pn4 {
nvidia,pins = "usb_vbus_en0_pn4";
nvidia,function = "usb";
- nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
nvidia,enable-input = <TEGRA_PIN_ENABLE>;
- nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
};
usb_vbus_en1_pn5 {
nvidia,pins = "usb_vbus_en1_pn5";
nvidia,function = "usb";
- nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
nvidia,enable-input = <TEGRA_PIN_ENABLE>;
- nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
};
hdmi_int_pn7 {
nvidia,pins = "hdmi_int_pn7";
@@ -1094,19 +1094,19 @@
};
cam_i2c_scl_pbb1 {
nvidia,pins = "cam_i2c_scl_pbb1";
- nvidia,function = "rsvd3";
- nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
- nvidia,tristate = <TEGRA_PIN_ENABLE>;
- nvidia,enable-input = <TEGRA_PIN_DISABLE>;
- nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ nvidia,function = "i2c3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
};
cam_i2c_sda_pbb2 {
nvidia,pins = "cam_i2c_sda_pbb2";
- nvidia,function = "rsvd3";
- nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
- nvidia,tristate = <TEGRA_PIN_ENABLE>;
- nvidia,enable-input = <TEGRA_PIN_DISABLE>;
- nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ nvidia,function = "i2c3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
};
pbb3 {
nvidia,pins = "pbb3";
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
@ 2015-05-13 14:13 ` Simon Glass
0 siblings, 0 replies; 20+ messages in thread
From: Simon Glass @ 2015-05-13 14:13 UTC (permalink / raw)
To: linux-arm-kernel
Regenerate the pinmux from the latest tegra-pinmux-scripts.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
arch/arm/boot/dts/tegra124-nyan-big.dts | 22 +++++++++++-----------
arch/arm/boot/dts/tegra124-nyan-blaze.dts | 30 +++++++++++++++---------------
2 files changed, 26 insertions(+), 26 deletions(-)
diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts b/arch/arm/boot/dts/tegra124-nyan-big.dts
index 2d21253..0eb2b0f 100644
--- a/arch/arm/boot/dts/tegra124-nyan-big.dts
+++ b/arch/arm/boot/dts/tegra124-nyan-big.dts
@@ -30,7 +30,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinmux_default>;
- pinmux_default: common {
+ state_default: pinmux {
clk_32k_out_pa0 {
nvidia,pins = "clk_32k_out_pa0";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
@@ -1098,19 +1098,19 @@
};
cam_i2c_scl_pbb1 {
nvidia,pins = "cam_i2c_scl_pbb1";
- nvidia,function = "rsvd3";
- nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
- nvidia,tristate = <TEGRA_PIN_ENABLE>;
- nvidia,enable-input = <TEGRA_PIN_DISABLE>;
- nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ nvidia,function = "i2c3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
};
cam_i2c_sda_pbb2 {
nvidia,pins = "cam_i2c_sda_pbb2";
- nvidia,function = "rsvd3";
- nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
- nvidia,tristate = <TEGRA_PIN_ENABLE>;
- nvidia,enable-input = <TEGRA_PIN_DISABLE>;
- nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ nvidia,function = "i2c3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
};
pbb3 {
nvidia,pins = "pbb3";
diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
index 0d30c51..1fc0da9 100644
--- a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
+++ b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
@@ -26,7 +26,7 @@
pinctrl-names = "default";
pinctrl-0 = <&pinmux_default>;
- pinmux_default: common {
+ state_default: pinmux {
clk_32k_out_pa0 {
nvidia,pins = "clk_32k_out_pa0";
nvidia,pull = <TEGRA_PIN_PULL_NONE>;
@@ -437,18 +437,18 @@
usb_vbus_en0_pn4 {
nvidia,pins = "usb_vbus_en0_pn4";
nvidia,function = "usb";
- nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
nvidia,enable-input = <TEGRA_PIN_ENABLE>;
- nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
};
usb_vbus_en1_pn5 {
nvidia,pins = "usb_vbus_en1_pn5";
nvidia,function = "usb";
- nvidia,pull = <TEGRA_PIN_PULL_UP>;
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
nvidia,tristate = <TEGRA_PIN_DISABLE>;
nvidia,enable-input = <TEGRA_PIN_ENABLE>;
- nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
};
hdmi_int_pn7 {
nvidia,pins = "hdmi_int_pn7";
@@ -1094,19 +1094,19 @@
};
cam_i2c_scl_pbb1 {
nvidia,pins = "cam_i2c_scl_pbb1";
- nvidia,function = "rsvd3";
- nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
- nvidia,tristate = <TEGRA_PIN_ENABLE>;
- nvidia,enable-input = <TEGRA_PIN_DISABLE>;
- nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ nvidia,function = "i2c3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
};
cam_i2c_sda_pbb2 {
nvidia,pins = "cam_i2c_sda_pbb2";
- nvidia,function = "rsvd3";
- nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
- nvidia,tristate = <TEGRA_PIN_ENABLE>;
- nvidia,enable-input = <TEGRA_PIN_DISABLE>;
- nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+ nvidia,function = "i2c3";
+ nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+ nvidia,tristate = <TEGRA_PIN_DISABLE>;
+ nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+ nvidia,open-drain = <TEGRA_PIN_ENABLE>;
};
pbb3 {
nvidia,pins = "pbb3";
--
2.2.0.rc0.207.ga3a616c
^ permalink raw reply related [flat|nested] 20+ messages in thread[parent not found: <1431526427-13340-1-git-send-email-sjg-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>]
* Re: [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
2015-05-13 14:13 ` Simon Glass
@ 2015-05-13 14:45 ` Stephen Warren
-1 siblings, 0 replies; 20+ messages in thread
From: Stephen Warren @ 2015-05-13 14:45 UTC (permalink / raw)
To: Simon Glass, Tomeu Vizoso
Cc: Stephen Warren, Thierry Reding,
linux-tegra-u79uwXL29TY76Z2rM5mHXA, Alexandre Courbot,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On 05/13/2015 08:13 AM, Simon Glass wrote:
> Regenerate the pinmux from the latest tegra-pinmux-scripts.
(Dropping most CCs; DT maintainers and lists generally don't get CC'd on
simple DT content changes but rather on schema adds/changes and perhaps
major DT content changes depending on context)
> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts b/arch/arm/boot/dts/tegra124-nyan-big.dts
> pinctrl-names = "default";
> pinctrl-0 = <&pinmux_default>;
>
> - pinmux_default: common {
> + state_default: pinmux {
This change will break compilation, since it changes the label name, yet
the old name is still referenced in pinctrl-0 above. Same applies in the
other file too.
> diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
> @@ -437,18 +437,18 @@
> usb_vbus_en0_pn4 {
> nvidia,pins = "usb_vbus_en0_pn4";
> nvidia,function = "usb";
> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
> nvidia,tristate = <TEGRA_PIN_DISABLE>;
> nvidia,enable-input = <TEGRA_PIN_ENABLE>;
> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
> };
> usb_vbus_en1_pn5 {
> nvidia,pins = "usb_vbus_en1_pn5";
> nvidia,function = "usb";
> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
> nvidia,tristate = <TEGRA_PIN_DISABLE>;
> nvidia,enable-input = <TEGRA_PIN_ENABLE>;
> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
> };
Tomeu, can you comment on those changes? Evidently the pinmux
configuration that's you added to the kernel doesn't exactly match the
pinmux configuration that you added to tegra-pinmux-scripts. Is the
change above correct, or do we need to propagate this change from the
kernel DT into tegra-pinmux-scripts, and hence also into the U-Boot
pinmux setup table?
My understanding of how these pins are generally used is that open-drain
is likely correct. I have no idea whether Tegra should supply the pullup
for these pins, or whether the board has a pullup resistor in which case
Tegra doesn't need to pull up.
^ permalink raw reply [flat|nested] 20+ messages in thread* [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
@ 2015-05-13 14:45 ` Stephen Warren
0 siblings, 0 replies; 20+ messages in thread
From: Stephen Warren @ 2015-05-13 14:45 UTC (permalink / raw)
To: linux-arm-kernel
On 05/13/2015 08:13 AM, Simon Glass wrote:
> Regenerate the pinmux from the latest tegra-pinmux-scripts.
(Dropping most CCs; DT maintainers and lists generally don't get CC'd on
simple DT content changes but rather on schema adds/changes and perhaps
major DT content changes depending on context)
> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts b/arch/arm/boot/dts/tegra124-nyan-big.dts
> pinctrl-names = "default";
> pinctrl-0 = <&pinmux_default>;
>
> - pinmux_default: common {
> + state_default: pinmux {
This change will break compilation, since it changes the label name, yet
the old name is still referenced in pinctrl-0 above. Same applies in the
other file too.
> diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
> @@ -437,18 +437,18 @@
> usb_vbus_en0_pn4 {
> nvidia,pins = "usb_vbus_en0_pn4";
> nvidia,function = "usb";
> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
> nvidia,tristate = <TEGRA_PIN_DISABLE>;
> nvidia,enable-input = <TEGRA_PIN_ENABLE>;
> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
> };
> usb_vbus_en1_pn5 {
> nvidia,pins = "usb_vbus_en1_pn5";
> nvidia,function = "usb";
> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
> nvidia,tristate = <TEGRA_PIN_DISABLE>;
> nvidia,enable-input = <TEGRA_PIN_ENABLE>;
> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
> };
Tomeu, can you comment on those changes? Evidently the pinmux
configuration that's you added to the kernel doesn't exactly match the
pinmux configuration that you added to tegra-pinmux-scripts. Is the
change above correct, or do we need to propagate this change from the
kernel DT into tegra-pinmux-scripts, and hence also into the U-Boot
pinmux setup table?
My understanding of how these pins are generally used is that open-drain
is likely correct. I have no idea whether Tegra should supply the pullup
for these pins, or whether the board has a pullup resistor in which case
Tegra doesn't need to pull up.
^ permalink raw reply [flat|nested] 20+ messages in thread[parent not found: <5553637C.5010506-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org>]
* Re: [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
2015-05-13 14:45 ` Stephen Warren
@ 2015-05-13 15:22 ` Simon Glass
-1 siblings, 0 replies; 20+ messages in thread
From: Simon Glass @ 2015-05-13 15:22 UTC (permalink / raw)
To: Stephen Warren
Cc: Tomeu Vizoso, Stephen Warren, Thierry Reding,
linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Alexandre Courbot, lak
Hi Stephen,
On 13 May 2015 at 08:45, Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org> wrote:
> On 05/13/2015 08:13 AM, Simon Glass wrote:
>>
>> Regenerate the pinmux from the latest tegra-pinmux-scripts.
>
>
> (Dropping most CCs; DT maintainers and lists generally don't get CC'd on
> simple DT content changes but rather on schema adds/changes and perhaps
> major DT content changes depending on context)
OK, I'll try to remember to use patman -m.
>
>> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts
>> b/arch/arm/boot/dts/tegra124-nyan-big.dts
>
>
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinmux_default>;
>>
>> - pinmux_default: common {
>> + state_default: pinmux {
>
>
> This change will break compilation, since it changes the label name, yet the
> old name is still referenced in pinctrl-0 above. Same applies in the other
> file too.
Yes I saw that, but assumed that the tool was doing the right thing.
Is the tool wrong?
>
>> diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>> b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>
>
>> @@ -437,18 +437,18 @@
>> usb_vbus_en0_pn4 {
>> nvidia,pins = "usb_vbus_en0_pn4";
>> nvidia,function = "usb";
>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>> nvidia,enable-input = <TEGRA_PIN_ENABLE>;
>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>> };
>> usb_vbus_en1_pn5 {
>> nvidia,pins = "usb_vbus_en1_pn5";
>> nvidia,function = "usb";
>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>> nvidia,enable-input = <TEGRA_PIN_ENABLE>;
>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>> };
>
>
> Tomeu, can you comment on those changes? Evidently the pinmux configuration
> that's you added to the kernel doesn't exactly match the pinmux
> configuration that you added to tegra-pinmux-scripts. Is the change above
> correct, or do we need to propagate this change from the kernel DT into
> tegra-pinmux-scripts, and hence also into the U-Boot pinmux setup table?
>
> My understanding of how these pins are generally used is that open-drain is
> likely correct. I have no idea whether Tegra should supply the pullup for
> these pins, or whether the board has a pullup resistor in which case Tegra
> doesn't need to pull up.
Regards,
Simon
^ permalink raw reply [flat|nested] 20+ messages in thread* [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
@ 2015-05-13 15:22 ` Simon Glass
0 siblings, 0 replies; 20+ messages in thread
From: Simon Glass @ 2015-05-13 15:22 UTC (permalink / raw)
To: linux-arm-kernel
Hi Stephen,
On 13 May 2015 at 08:45, Stephen Warren <swarren@wwwdotorg.org> wrote:
> On 05/13/2015 08:13 AM, Simon Glass wrote:
>>
>> Regenerate the pinmux from the latest tegra-pinmux-scripts.
>
>
> (Dropping most CCs; DT maintainers and lists generally don't get CC'd on
> simple DT content changes but rather on schema adds/changes and perhaps
> major DT content changes depending on context)
OK, I'll try to remember to use patman -m.
>
>> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts
>> b/arch/arm/boot/dts/tegra124-nyan-big.dts
>
>
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinmux_default>;
>>
>> - pinmux_default: common {
>> + state_default: pinmux {
>
>
> This change will break compilation, since it changes the label name, yet the
> old name is still referenced in pinctrl-0 above. Same applies in the other
> file too.
Yes I saw that, but assumed that the tool was doing the right thing.
Is the tool wrong?
>
>> diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>> b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>
>
>> @@ -437,18 +437,18 @@
>> usb_vbus_en0_pn4 {
>> nvidia,pins = "usb_vbus_en0_pn4";
>> nvidia,function = "usb";
>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>> nvidia,enable-input = <TEGRA_PIN_ENABLE>;
>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>> };
>> usb_vbus_en1_pn5 {
>> nvidia,pins = "usb_vbus_en1_pn5";
>> nvidia,function = "usb";
>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>> nvidia,enable-input = <TEGRA_PIN_ENABLE>;
>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>> };
>
>
> Tomeu, can you comment on those changes? Evidently the pinmux configuration
> that's you added to the kernel doesn't exactly match the pinmux
> configuration that you added to tegra-pinmux-scripts. Is the change above
> correct, or do we need to propagate this change from the kernel DT into
> tegra-pinmux-scripts, and hence also into the U-Boot pinmux setup table?
>
> My understanding of how these pins are generally used is that open-drain is
> likely correct. I have no idea whether Tegra should supply the pullup for
> these pins, or whether the board has a pullup resistor in which case Tegra
> doesn't need to pull up.
Regards,
Simon
^ permalink raw reply [flat|nested] 20+ messages in thread[parent not found: <CAPnjgZ0ga6==w7YWQoeUtXRxUhCjQ+BHMJuCL7vbqN9WTLM2kQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>]
* Re: [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
2015-05-13 15:22 ` Simon Glass
@ 2015-05-14 14:21 ` Stephen Warren
-1 siblings, 0 replies; 20+ messages in thread
From: Stephen Warren @ 2015-05-14 14:21 UTC (permalink / raw)
To: Simon Glass
Cc: Tomeu Vizoso, Stephen Warren, Thierry Reding,
linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Alexandre Courbot, lak
On 05/13/2015 09:22 AM, Simon Glass wrote:
> Hi Stephen,
>
> On 13 May 2015 at 08:45, Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org> wrote:
>> On 05/13/2015 08:13 AM, Simon Glass wrote:
>>>
>>> Regenerate the pinmux from the latest tegra-pinmux-scripts.
>>
>>
>> (Dropping most CCs; DT maintainers and lists generally don't get CC'd on
>> simple DT content changes but rather on schema adds/changes and perhaps
>> major DT content changes depending on context)
>
> OK, I'll try to remember to use patman -m.
>
>>
>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts
>>> b/arch/arm/boot/dts/tegra124-nyan-big.dts
>>
>>
>>> pinctrl-names = "default";
>>> pinctrl-0 = <&pinmux_default>;
>>>
>>> - pinmux_default: common {
>>> + state_default: pinmux {
>>
>>
>> This change will break compilation, since it changes the label name, yet the
>> old name is still referenced in pinctrl-0 above. Same applies in the other
>> file too.
>
> Yes I saw that, but assumed that the tool was doing the right thing.
> Is the tool wrong?
Well, it includes the outer node to make it obvious where to put the
generated data, but since this one line doesn't exactly match what's in
some of the kernel DTs, it's probably just confusing. I've sent a patch
to remove that one line from the generated output of the tool; find it
on the linux-tegra mailing list.
^ permalink raw reply [flat|nested] 20+ messages in thread* [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
@ 2015-05-14 14:21 ` Stephen Warren
0 siblings, 0 replies; 20+ messages in thread
From: Stephen Warren @ 2015-05-14 14:21 UTC (permalink / raw)
To: linux-arm-kernel
On 05/13/2015 09:22 AM, Simon Glass wrote:
> Hi Stephen,
>
> On 13 May 2015 at 08:45, Stephen Warren <swarren@wwwdotorg.org> wrote:
>> On 05/13/2015 08:13 AM, Simon Glass wrote:
>>>
>>> Regenerate the pinmux from the latest tegra-pinmux-scripts.
>>
>>
>> (Dropping most CCs; DT maintainers and lists generally don't get CC'd on
>> simple DT content changes but rather on schema adds/changes and perhaps
>> major DT content changes depending on context)
>
> OK, I'll try to remember to use patman -m.
>
>>
>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts
>>> b/arch/arm/boot/dts/tegra124-nyan-big.dts
>>
>>
>>> pinctrl-names = "default";
>>> pinctrl-0 = <&pinmux_default>;
>>>
>>> - pinmux_default: common {
>>> + state_default: pinmux {
>>
>>
>> This change will break compilation, since it changes the label name, yet the
>> old name is still referenced in pinctrl-0 above. Same applies in the other
>> file too.
>
> Yes I saw that, but assumed that the tool was doing the right thing.
> Is the tool wrong?
Well, it includes the outer node to make it obvious where to put the
generated data, but since this one line doesn't exactly match what's in
some of the kernel DTs, it's probably just confusing. I've sent a patch
to remove that one line from the generated output of the tool; find it
on the linux-tegra mailing list.
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
2015-05-13 14:45 ` Stephen Warren
@ 2015-05-14 13:09 ` Tomeu Vizoso
-1 siblings, 0 replies; 20+ messages in thread
From: Tomeu Vizoso @ 2015-05-14 13:09 UTC (permalink / raw)
To: Stephen Warren
Cc: Simon Glass, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Alexandre Courbot, Thierry Reding, Stephen Warren,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
Andrew Bresticker
On 13 May 2015 at 16:45, Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org> wrote:
> On 05/13/2015 08:13 AM, Simon Glass wrote:
>>
>> Regenerate the pinmux from the latest tegra-pinmux-scripts.
>
>
> (Dropping most CCs; DT maintainers and lists generally don't get CC'd on
> simple DT content changes but rather on schema adds/changes and perhaps
> major DT content changes depending on context)
>
>> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts
>> b/arch/arm/boot/dts/tegra124-nyan-big.dts
>
>
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinmux_default>;
>>
>> - pinmux_default: common {
>> + state_default: pinmux {
>
>
> This change will break compilation, since it changes the label name, yet the
> old name is still referenced in pinctrl-0 above. Same applies in the other
> file too.
>
>> diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>> b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>
>
>> @@ -437,18 +437,18 @@
>> usb_vbus_en0_pn4 {
>> nvidia,pins = "usb_vbus_en0_pn4";
>> nvidia,function = "usb";
>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>> nvidia,enable-input = <TEGRA_PIN_ENABLE>;
>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>> };
>> usb_vbus_en1_pn5 {
>> nvidia,pins = "usb_vbus_en1_pn5";
>> nvidia,function = "usb";
>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>> nvidia,enable-input = <TEGRA_PIN_ENABLE>;
>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>> };
>
>
> Tomeu, can you comment on those changes? Evidently the pinmux configuration
> that's you added to the kernel doesn't exactly match the pinmux
> configuration that you added to tegra-pinmux-scripts.
Are you sure? Just checked and what tegra-pinmux-scripts currently
generates matches what is currently in the kernel, for both nyans.
> Is the change above
> correct, or do we need to propagate this change from the kernel DT into
> tegra-pinmux-scripts, and hence also into the U-Boot pinmux setup table?
>
> My understanding of how these pins are generally used is that open-drain is
> likely correct. I have no idea whether Tegra should supply the pullup for
> these pins, or whether the board has a pullup resistor in which case Tegra
> doesn't need to pull up.
From what Andrew (added to CC) said when these changes were discussed,
it shouldn't matter as a fixed regulator is used to drive those pins
high.
Regards,
Tomeu
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 20+ messages in thread* [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
@ 2015-05-14 13:09 ` Tomeu Vizoso
0 siblings, 0 replies; 20+ messages in thread
From: Tomeu Vizoso @ 2015-05-14 13:09 UTC (permalink / raw)
To: linux-arm-kernel
On 13 May 2015 at 16:45, Stephen Warren <swarren@wwwdotorg.org> wrote:
> On 05/13/2015 08:13 AM, Simon Glass wrote:
>>
>> Regenerate the pinmux from the latest tegra-pinmux-scripts.
>
>
> (Dropping most CCs; DT maintainers and lists generally don't get CC'd on
> simple DT content changes but rather on schema adds/changes and perhaps
> major DT content changes depending on context)
>
>> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts
>> b/arch/arm/boot/dts/tegra124-nyan-big.dts
>
>
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinmux_default>;
>>
>> - pinmux_default: common {
>> + state_default: pinmux {
>
>
> This change will break compilation, since it changes the label name, yet the
> old name is still referenced in pinctrl-0 above. Same applies in the other
> file too.
>
>> diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>> b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>
>
>> @@ -437,18 +437,18 @@
>> usb_vbus_en0_pn4 {
>> nvidia,pins = "usb_vbus_en0_pn4";
>> nvidia,function = "usb";
>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>> nvidia,enable-input = <TEGRA_PIN_ENABLE>;
>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>> };
>> usb_vbus_en1_pn5 {
>> nvidia,pins = "usb_vbus_en1_pn5";
>> nvidia,function = "usb";
>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>> nvidia,enable-input = <TEGRA_PIN_ENABLE>;
>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>> };
>
>
> Tomeu, can you comment on those changes? Evidently the pinmux configuration
> that's you added to the kernel doesn't exactly match the pinmux
> configuration that you added to tegra-pinmux-scripts.
Are you sure? Just checked and what tegra-pinmux-scripts currently
generates matches what is currently in the kernel, for both nyans.
> Is the change above
> correct, or do we need to propagate this change from the kernel DT into
> tegra-pinmux-scripts, and hence also into the U-Boot pinmux setup table?
>
> My understanding of how these pins are generally used is that open-drain is
> likely correct. I have no idea whether Tegra should supply the pullup for
> these pins, or whether the board has a pullup resistor in which case Tegra
> doesn't need to pull up.
>From what Andrew (added to CC) said when these changes were discussed,
it shouldn't matter as a fixed regulator is used to drive those pins
high.
Regards,
Tomeu
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 20+ messages in thread[parent not found: <CAAObsKCxFJA=6kyHM5rtpJMVRZRDbBO3KSn+QdNoOQz1rXCWTQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>]
* Re: [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
2015-05-14 13:09 ` Tomeu Vizoso
@ 2015-05-14 14:11 ` Stephen Warren
-1 siblings, 0 replies; 20+ messages in thread
From: Stephen Warren @ 2015-05-14 14:11 UTC (permalink / raw)
To: Tomeu Vizoso, Simon Glass
Cc: linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Alexandre Courbot, Thierry Reding, Stephen Warren,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
Andrew Bresticker
On 05/14/2015 07:09 AM, Tomeu Vizoso wrote:
> On 13 May 2015 at 16:45, Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org> wrote:
>> On 05/13/2015 08:13 AM, Simon Glass wrote:
>>>
>>> Regenerate the pinmux from the latest tegra-pinmux-scripts.
>>
>>
>> (Dropping most CCs; DT maintainers and lists generally don't get CC'd on
>> simple DT content changes but rather on schema adds/changes and perhaps
>> major DT content changes depending on context)
>>
>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts
>>> b/arch/arm/boot/dts/tegra124-nyan-big.dts
>>
>>
>>> pinctrl-names = "default";
>>> pinctrl-0 = <&pinmux_default>;
>>>
>>> - pinmux_default: common {
>>> + state_default: pinmux {
>>
>>
>> This change will break compilation, since it changes the label name, yet the
>> old name is still referenced in pinctrl-0 above. Same applies in the other
>> file too.
>>
>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>> b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>
>>
>>> @@ -437,18 +437,18 @@
>>> usb_vbus_en0_pn4 {
>>> nvidia,pins = "usb_vbus_en0_pn4";
>>> nvidia,function = "usb";
>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>> nvidia,enable-input = <TEGRA_PIN_ENABLE>;
>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>> };
>>> usb_vbus_en1_pn5 {
>>> nvidia,pins = "usb_vbus_en1_pn5";
>>> nvidia,function = "usb";
>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>> nvidia,enable-input = <TEGRA_PIN_ENABLE>;
>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>> };
>>
>>
>> Tomeu, can you comment on those changes? Evidently the pinmux configuration
>> that's you added to the kernel doesn't exactly match the pinmux
>> configuration that you added to tegra-pinmux-scripts.
>
> Are you sure? Just checked and what tegra-pinmux-scripts currently
> generates matches what is currently in the kernel, for both nyans.
My apologies; you're correct.
This patch to the kernel DTs includes changes that aren't generated by
either current tegra-pinmux-scripts, nor by tegra-pinmux-scripts with
Simon's "[pinmux scripts PATCH] Support TPM on nyan boards" applied.
Simon, can you double-check you didn't have any local patches to
tegra-pinmux-scripts applied when you generated the DT content for this
patch?
>> Is the change above
>> correct, or do we need to propagate this change from the kernel DT into
>> tegra-pinmux-scripts, and hence also into the U-Boot pinmux setup table?
>>
>> My understanding of how these pins are generally used is that open-drain is
>> likely correct. I have no idea whether Tegra should supply the pullup for
>> these pins, or whether the board has a pullup resistor in which case Tegra
>> doesn't need to pull up.
>
> From what Andrew (added to CC) said when these changes were discussed,
> it shouldn't matter as a fixed regulator is used to drive those pins
> high.
It looks like nyan-big and nyan-blaze configure these pins differently,
which may be incorrect if the boards are truly almost identical. Is that
expected? Nyan-big sets them both to open-drain but Nyan-blaze sets them
to push-pull. The pull-up enable is different too. Typically these pins
are open-drain, because there's often a current sensor chip on the USB
port power rail which asserts (pulls low in open-drain mode) these
signals to turn off the power when an over-current condition is
detected. Not all boards do this though, so the difference may be
perfectly expected; someone with access to the schematics would have to
check.
^ permalink raw reply [flat|nested] 20+ messages in thread* [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
@ 2015-05-14 14:11 ` Stephen Warren
0 siblings, 0 replies; 20+ messages in thread
From: Stephen Warren @ 2015-05-14 14:11 UTC (permalink / raw)
To: linux-arm-kernel
On 05/14/2015 07:09 AM, Tomeu Vizoso wrote:
> On 13 May 2015 at 16:45, Stephen Warren <swarren@wwwdotorg.org> wrote:
>> On 05/13/2015 08:13 AM, Simon Glass wrote:
>>>
>>> Regenerate the pinmux from the latest tegra-pinmux-scripts.
>>
>>
>> (Dropping most CCs; DT maintainers and lists generally don't get CC'd on
>> simple DT content changes but rather on schema adds/changes and perhaps
>> major DT content changes depending on context)
>>
>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts
>>> b/arch/arm/boot/dts/tegra124-nyan-big.dts
>>
>>
>>> pinctrl-names = "default";
>>> pinctrl-0 = <&pinmux_default>;
>>>
>>> - pinmux_default: common {
>>> + state_default: pinmux {
>>
>>
>> This change will break compilation, since it changes the label name, yet the
>> old name is still referenced in pinctrl-0 above. Same applies in the other
>> file too.
>>
>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>> b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>
>>
>>> @@ -437,18 +437,18 @@
>>> usb_vbus_en0_pn4 {
>>> nvidia,pins = "usb_vbus_en0_pn4";
>>> nvidia,function = "usb";
>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>> nvidia,enable-input = <TEGRA_PIN_ENABLE>;
>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>> };
>>> usb_vbus_en1_pn5 {
>>> nvidia,pins = "usb_vbus_en1_pn5";
>>> nvidia,function = "usb";
>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>> nvidia,enable-input = <TEGRA_PIN_ENABLE>;
>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>> };
>>
>>
>> Tomeu, can you comment on those changes? Evidently the pinmux configuration
>> that's you added to the kernel doesn't exactly match the pinmux
>> configuration that you added to tegra-pinmux-scripts.
>
> Are you sure? Just checked and what tegra-pinmux-scripts currently
> generates matches what is currently in the kernel, for both nyans.
My apologies; you're correct.
This patch to the kernel DTs includes changes that aren't generated by
either current tegra-pinmux-scripts, nor by tegra-pinmux-scripts with
Simon's "[pinmux scripts PATCH] Support TPM on nyan boards" applied.
Simon, can you double-check you didn't have any local patches to
tegra-pinmux-scripts applied when you generated the DT content for this
patch?
>> Is the change above
>> correct, or do we need to propagate this change from the kernel DT into
>> tegra-pinmux-scripts, and hence also into the U-Boot pinmux setup table?
>>
>> My understanding of how these pins are generally used is that open-drain is
>> likely correct. I have no idea whether Tegra should supply the pullup for
>> these pins, or whether the board has a pullup resistor in which case Tegra
>> doesn't need to pull up.
>
> From what Andrew (added to CC) said when these changes were discussed,
> it shouldn't matter as a fixed regulator is used to drive those pins
> high.
It looks like nyan-big and nyan-blaze configure these pins differently,
which may be incorrect if the boards are truly almost identical. Is that
expected? Nyan-big sets them both to open-drain but Nyan-blaze sets them
to push-pull. The pull-up enable is different too. Typically these pins
are open-drain, because there's often a current sensor chip on the USB
port power rail which asserts (pulls low in open-drain mode) these
signals to turn off the power when an over-current condition is
detected. Not all boards do this though, so the difference may be
perfectly expected; someone with access to the schematics would have to
check.
^ permalink raw reply [flat|nested] 20+ messages in thread[parent not found: <5554AD0B.1060106-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org>]
* Re: [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
2015-05-14 14:11 ` Stephen Warren
@ 2015-05-14 14:28 ` Simon Glass
-1 siblings, 0 replies; 20+ messages in thread
From: Simon Glass @ 2015-05-14 14:28 UTC (permalink / raw)
To: Stephen Warren
Cc: Tomeu Vizoso, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Alexandre Courbot, Thierry Reding, Stephen Warren,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
Andrew Bresticker
Hi Stephen,
On 14 May 2015 at 08:11, Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org> wrote:
> On 05/14/2015 07:09 AM, Tomeu Vizoso wrote:
>>
>> On 13 May 2015 at 16:45, Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org> wrote:
>>>
>>> On 05/13/2015 08:13 AM, Simon Glass wrote:
>>>>
>>>>
>>>> Regenerate the pinmux from the latest tegra-pinmux-scripts.
>>>
>>>
>>>
>>> (Dropping most CCs; DT maintainers and lists generally don't get CC'd on
>>> simple DT content changes but rather on schema adds/changes and perhaps
>>> major DT content changes depending on context)
>>>
>>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts
>>>> b/arch/arm/boot/dts/tegra124-nyan-big.dts
>>>
>>>
>>>
>>>> pinctrl-names = "default";
>>>> pinctrl-0 = <&pinmux_default>;
>>>>
>>>> - pinmux_default: common {
>>>> + state_default: pinmux {
>>>
>>>
>>>
>>> This change will break compilation, since it changes the label name, yet
>>> the
>>> old name is still referenced in pinctrl-0 above. Same applies in the
>>> other
>>> file too.
>>>
>>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>>> b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>>
>>>
>>>
>>>> @@ -437,18 +437,18 @@
>>>> usb_vbus_en0_pn4 {
>>>> nvidia,pins = "usb_vbus_en0_pn4";
>>>> nvidia,function = "usb";
>>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>>> nvidia,enable-input =
>>>> <TEGRA_PIN_ENABLE>;
>>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>>> };
>>>> usb_vbus_en1_pn5 {
>>>> nvidia,pins = "usb_vbus_en1_pn5";
>>>> nvidia,function = "usb";
>>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>>> nvidia,enable-input =
>>>> <TEGRA_PIN_ENABLE>;
>>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>>> };
>>>
>>>
>>>
>>> Tomeu, can you comment on those changes? Evidently the pinmux
>>> configuration
>>> that's you added to the kernel doesn't exactly match the pinmux
>>> configuration that you added to tegra-pinmux-scripts.
>>
>>
>> Are you sure? Just checked and what tegra-pinmux-scripts currently
>> generates matches what is currently in the kernel, for both nyans.
>
>
> My apologies; you're correct.
>
> This patch to the kernel DTs includes changes that aren't generated by
> either current tegra-pinmux-scripts, nor by tegra-pinmux-scripts with
> Simon's "[pinmux scripts PATCH] Support TPM on nyan boards" applied. Simon,
> can you double-check you didn't have any local patches to
> tegra-pinmux-scripts applied when you generated the DT content for this
> patch?
Yes. Apart from my patch the top commit is 39af.
>
>>> Is the change above
>>> correct, or do we need to propagate this change from the kernel DT into
>>> tegra-pinmux-scripts, and hence also into the U-Boot pinmux setup table?
>>>
>>> My understanding of how these pins are generally used is that open-drain
>>> is
>>> likely correct. I have no idea whether Tegra should supply the pullup for
>>> these pins, or whether the board has a pullup resistor in which case
>>> Tegra
>>> doesn't need to pull up.
>>
>>
>> From what Andrew (added to CC) said when these changes were discussed,
>> it shouldn't matter as a fixed regulator is used to drive those pins
>> high.
>
>
> It looks like nyan-big and nyan-blaze configure these pins differently,
> which may be incorrect if the boards are truly almost identical. Is that
> expected? Nyan-big sets them both to open-drain but Nyan-blaze sets them to
> push-pull. The pull-up enable is different too. Typically these pins are
> open-drain, because there's often a current sensor chip on the USB port
> power rail which asserts (pulls low in open-drain mode) these signals to
> turn off the power when an over-current condition is detected. Not all
> boards do this though, so the difference may be perfectly expected; someone
> with access to the schematics would have to check.
Regards,
Simon
^ permalink raw reply [flat|nested] 20+ messages in thread* [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
@ 2015-05-14 14:28 ` Simon Glass
0 siblings, 0 replies; 20+ messages in thread
From: Simon Glass @ 2015-05-14 14:28 UTC (permalink / raw)
To: linux-arm-kernel
Hi Stephen,
On 14 May 2015 at 08:11, Stephen Warren <swarren@wwwdotorg.org> wrote:
> On 05/14/2015 07:09 AM, Tomeu Vizoso wrote:
>>
>> On 13 May 2015 at 16:45, Stephen Warren <swarren@wwwdotorg.org> wrote:
>>>
>>> On 05/13/2015 08:13 AM, Simon Glass wrote:
>>>>
>>>>
>>>> Regenerate the pinmux from the latest tegra-pinmux-scripts.
>>>
>>>
>>>
>>> (Dropping most CCs; DT maintainers and lists generally don't get CC'd on
>>> simple DT content changes but rather on schema adds/changes and perhaps
>>> major DT content changes depending on context)
>>>
>>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts
>>>> b/arch/arm/boot/dts/tegra124-nyan-big.dts
>>>
>>>
>>>
>>>> pinctrl-names = "default";
>>>> pinctrl-0 = <&pinmux_default>;
>>>>
>>>> - pinmux_default: common {
>>>> + state_default: pinmux {
>>>
>>>
>>>
>>> This change will break compilation, since it changes the label name, yet
>>> the
>>> old name is still referenced in pinctrl-0 above. Same applies in the
>>> other
>>> file too.
>>>
>>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>>> b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>>
>>>
>>>
>>>> @@ -437,18 +437,18 @@
>>>> usb_vbus_en0_pn4 {
>>>> nvidia,pins = "usb_vbus_en0_pn4";
>>>> nvidia,function = "usb";
>>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>>> nvidia,enable-input =
>>>> <TEGRA_PIN_ENABLE>;
>>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>>> };
>>>> usb_vbus_en1_pn5 {
>>>> nvidia,pins = "usb_vbus_en1_pn5";
>>>> nvidia,function = "usb";
>>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>>> nvidia,enable-input =
>>>> <TEGRA_PIN_ENABLE>;
>>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>>> };
>>>
>>>
>>>
>>> Tomeu, can you comment on those changes? Evidently the pinmux
>>> configuration
>>> that's you added to the kernel doesn't exactly match the pinmux
>>> configuration that you added to tegra-pinmux-scripts.
>>
>>
>> Are you sure? Just checked and what tegra-pinmux-scripts currently
>> generates matches what is currently in the kernel, for both nyans.
>
>
> My apologies; you're correct.
>
> This patch to the kernel DTs includes changes that aren't generated by
> either current tegra-pinmux-scripts, nor by tegra-pinmux-scripts with
> Simon's "[pinmux scripts PATCH] Support TPM on nyan boards" applied. Simon,
> can you double-check you didn't have any local patches to
> tegra-pinmux-scripts applied when you generated the DT content for this
> patch?
Yes. Apart from my patch the top commit is 39af.
>
>>> Is the change above
>>> correct, or do we need to propagate this change from the kernel DT into
>>> tegra-pinmux-scripts, and hence also into the U-Boot pinmux setup table?
>>>
>>> My understanding of how these pins are generally used is that open-drain
>>> is
>>> likely correct. I have no idea whether Tegra should supply the pullup for
>>> these pins, or whether the board has a pullup resistor in which case
>>> Tegra
>>> doesn't need to pull up.
>>
>>
>> From what Andrew (added to CC) said when these changes were discussed,
>> it shouldn't matter as a fixed regulator is used to drive those pins
>> high.
>
>
> It looks like nyan-big and nyan-blaze configure these pins differently,
> which may be incorrect if the boards are truly almost identical. Is that
> expected? Nyan-big sets them both to open-drain but Nyan-blaze sets them to
> push-pull. The pull-up enable is different too. Typically these pins are
> open-drain, because there's often a current sensor chip on the USB port
> power rail which asserts (pulls low in open-drain mode) these signals to
> turn off the power when an over-current condition is detected. Not all
> boards do this though, so the difference may be perfectly expected; someone
> with access to the schematics would have to check.
Regards,
Simon
^ permalink raw reply [flat|nested] 20+ messages in thread[parent not found: <CAPnjgZ2QrTu=D_AapTded+_NR1waZTbNoN8rCtHnTdd0OdnwLA-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>]
* Re: [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
2015-05-14 14:28 ` Simon Glass
@ 2015-05-14 15:47 ` Stephen Warren
-1 siblings, 0 replies; 20+ messages in thread
From: Stephen Warren @ 2015-05-14 15:47 UTC (permalink / raw)
To: Simon Glass
Cc: Tomeu Vizoso, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Alexandre Courbot, Thierry Reding, Stephen Warren,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
Andrew Bresticker
On 05/14/2015 08:28 AM, Simon Glass wrote:
> Hi Stephen,
>
> On 14 May 2015 at 08:11, Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org> wrote:
>> On 05/14/2015 07:09 AM, Tomeu Vizoso wrote:
>>>
>>> On 13 May 2015 at 16:45, Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org> wrote:
>>>>
>>>> On 05/13/2015 08:13 AM, Simon Glass wrote:
>>>>>
>>>>>
>>>>> Regenerate the pinmux from the latest tegra-pinmux-scripts.
>>>>
>>>>
>>>>
>>>> (Dropping most CCs; DT maintainers and lists generally don't get CC'd on
>>>> simple DT content changes but rather on schema adds/changes and perhaps
>>>> major DT content changes depending on context)
>>>>
>>>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts
>>>>> b/arch/arm/boot/dts/tegra124-nyan-big.dts
>>>>
>>>>
>>>>
>>>>> pinctrl-names = "default";
>>>>> pinctrl-0 = <&pinmux_default>;
>>>>>
>>>>> - pinmux_default: common {
>>>>> + state_default: pinmux {
>>>>
>>>>
>>>>
>>>> This change will break compilation, since it changes the label name, yet
>>>> the
>>>> old name is still referenced in pinctrl-0 above. Same applies in the
>>>> other
>>>> file too.
>>>>
>>>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>>>> b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>>>
>>>>
>>>>
>>>>> @@ -437,18 +437,18 @@
>>>>> usb_vbus_en0_pn4 {
>>>>> nvidia,pins = "usb_vbus_en0_pn4";
>>>>> nvidia,function = "usb";
>>>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>>>> nvidia,enable-input =
>>>>> <TEGRA_PIN_ENABLE>;
>>>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>>>> };
>>>>> usb_vbus_en1_pn5 {
>>>>> nvidia,pins = "usb_vbus_en1_pn5";
>>>>> nvidia,function = "usb";
>>>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>>>> nvidia,enable-input =
>>>>> <TEGRA_PIN_ENABLE>;
>>>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>>>> };
>>>>
>>>>
>>>>
>>>> Tomeu, can you comment on those changes? Evidently the pinmux
>>>> configuration
>>>> that's you added to the kernel doesn't exactly match the pinmux
>>>> configuration that you added to tegra-pinmux-scripts.
>>>
>>>
>>> Are you sure? Just checked and what tegra-pinmux-scripts currently
>>> generates matches what is currently in the kernel, for both nyans.
>>
>>
>> My apologies; you're correct.
>>
>> This patch to the kernel DTs includes changes that aren't generated by
>> either current tegra-pinmux-scripts, nor by tegra-pinmux-scripts with
>> Simon's "[pinmux scripts PATCH] Support TPM on nyan boards" applied. Simon,
>> can you double-check you didn't have any local patches to
>> tegra-pinmux-scripts applied when you generated the DT content for this
>> patch?
>
> Yes. Apart from my patch the top commit is 39af.
OK, did you paste the same DT content into both DTs then, instead of
generating each DT separately?
When I re-generate the DT using commit 39af, I don't get any changes to
usb_vbus_en*.
^ permalink raw reply [flat|nested] 20+ messages in thread* [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
@ 2015-05-14 15:47 ` Stephen Warren
0 siblings, 0 replies; 20+ messages in thread
From: Stephen Warren @ 2015-05-14 15:47 UTC (permalink / raw)
To: linux-arm-kernel
On 05/14/2015 08:28 AM, Simon Glass wrote:
> Hi Stephen,
>
> On 14 May 2015 at 08:11, Stephen Warren <swarren@wwwdotorg.org> wrote:
>> On 05/14/2015 07:09 AM, Tomeu Vizoso wrote:
>>>
>>> On 13 May 2015 at 16:45, Stephen Warren <swarren@wwwdotorg.org> wrote:
>>>>
>>>> On 05/13/2015 08:13 AM, Simon Glass wrote:
>>>>>
>>>>>
>>>>> Regenerate the pinmux from the latest tegra-pinmux-scripts.
>>>>
>>>>
>>>>
>>>> (Dropping most CCs; DT maintainers and lists generally don't get CC'd on
>>>> simple DT content changes but rather on schema adds/changes and perhaps
>>>> major DT content changes depending on context)
>>>>
>>>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts
>>>>> b/arch/arm/boot/dts/tegra124-nyan-big.dts
>>>>
>>>>
>>>>
>>>>> pinctrl-names = "default";
>>>>> pinctrl-0 = <&pinmux_default>;
>>>>>
>>>>> - pinmux_default: common {
>>>>> + state_default: pinmux {
>>>>
>>>>
>>>>
>>>> This change will break compilation, since it changes the label name, yet
>>>> the
>>>> old name is still referenced in pinctrl-0 above. Same applies in the
>>>> other
>>>> file too.
>>>>
>>>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>>>> b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>>>
>>>>
>>>>
>>>>> @@ -437,18 +437,18 @@
>>>>> usb_vbus_en0_pn4 {
>>>>> nvidia,pins = "usb_vbus_en0_pn4";
>>>>> nvidia,function = "usb";
>>>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>>>> nvidia,enable-input =
>>>>> <TEGRA_PIN_ENABLE>;
>>>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>>>> };
>>>>> usb_vbus_en1_pn5 {
>>>>> nvidia,pins = "usb_vbus_en1_pn5";
>>>>> nvidia,function = "usb";
>>>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>>>> nvidia,enable-input =
>>>>> <TEGRA_PIN_ENABLE>;
>>>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>>>> };
>>>>
>>>>
>>>>
>>>> Tomeu, can you comment on those changes? Evidently the pinmux
>>>> configuration
>>>> that's you added to the kernel doesn't exactly match the pinmux
>>>> configuration that you added to tegra-pinmux-scripts.
>>>
>>>
>>> Are you sure? Just checked and what tegra-pinmux-scripts currently
>>> generates matches what is currently in the kernel, for both nyans.
>>
>>
>> My apologies; you're correct.
>>
>> This patch to the kernel DTs includes changes that aren't generated by
>> either current tegra-pinmux-scripts, nor by tegra-pinmux-scripts with
>> Simon's "[pinmux scripts PATCH] Support TPM on nyan boards" applied. Simon,
>> can you double-check you didn't have any local patches to
>> tegra-pinmux-scripts applied when you generated the DT content for this
>> patch?
>
> Yes. Apart from my patch the top commit is 39af.
OK, did you paste the same DT content into both DTs then, instead of
generating each DT separately?
When I re-generate the DT using commit 39af, I don't get any changes to
usb_vbus_en*.
^ permalink raw reply [flat|nested] 20+ messages in thread[parent not found: <5554C399.4060807-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org>]
* Re: [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
2015-05-14 15:47 ` Stephen Warren
@ 2015-05-14 16:30 ` Simon Glass
-1 siblings, 0 replies; 20+ messages in thread
From: Simon Glass @ 2015-05-14 16:30 UTC (permalink / raw)
To: Stephen Warren
Cc: Tomeu Vizoso, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Alexandre Courbot, Thierry Reding, Stephen Warren,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
Andrew Bresticker
Hi Stephen,
On 14 May 2015 at 09:47, Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org> wrote:
>
> On 05/14/2015 08:28 AM, Simon Glass wrote:
>>
>> Hi Stephen,
>>
>> On 14 May 2015 at 08:11, Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org> wrote:
>>>
>>> On 05/14/2015 07:09 AM, Tomeu Vizoso wrote:
>>>>
>>>>
>>>> On 13 May 2015 at 16:45, Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org> wrote:
>>>>>
>>>>>
>>>>> On 05/13/2015 08:13 AM, Simon Glass wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>> Regenerate the pinmux from the latest tegra-pinmux-scripts.
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> (Dropping most CCs; DT maintainers and lists generally don't get CC'd on
>>>>> simple DT content changes but rather on schema adds/changes and perhaps
>>>>> major DT content changes depending on context)
>>>>>
>>>>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts
>>>>>> b/arch/arm/boot/dts/tegra124-nyan-big.dts
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>> pinctrl-names = "default";
>>>>>> pinctrl-0 = <&pinmux_default>;
>>>>>>
>>>>>> - pinmux_default: common {
>>>>>> + state_default: pinmux {
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> This change will break compilation, since it changes the label name, yet
>>>>> the
>>>>> old name is still referenced in pinctrl-0 above. Same applies in the
>>>>> other
>>>>> file too.
>>>>>
>>>>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>>>>> b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>> @@ -437,18 +437,18 @@
>>>>>> usb_vbus_en0_pn4 {
>>>>>> nvidia,pins = "usb_vbus_en0_pn4";
>>>>>> nvidia,function = "usb";
>>>>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>>>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>>>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>>>>> nvidia,enable-input =
>>>>>> <TEGRA_PIN_ENABLE>;
>>>>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>>>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>>>>> };
>>>>>> usb_vbus_en1_pn5 {
>>>>>> nvidia,pins = "usb_vbus_en1_pn5";
>>>>>> nvidia,function = "usb";
>>>>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>>>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>>>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>>>>> nvidia,enable-input =
>>>>>> <TEGRA_PIN_ENABLE>;
>>>>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>>>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>>>>> };
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> Tomeu, can you comment on those changes? Evidently the pinmux
>>>>> configuration
>>>>> that's you added to the kernel doesn't exactly match the pinmux
>>>>> configuration that you added to tegra-pinmux-scripts.
>>>>
>>>>
>>>>
>>>> Are you sure? Just checked and what tegra-pinmux-scripts currently
>>>> generates matches what is currently in the kernel, for both nyans.
>>>
>>>
>>>
>>> My apologies; you're correct.
>>>
>>> This patch to the kernel DTs includes changes that aren't generated by
>>> either current tegra-pinmux-scripts, nor by tegra-pinmux-scripts with
>>> Simon's "[pinmux scripts PATCH] Support TPM on nyan boards" applied. Simon,
>>> can you double-check you didn't have any local patches to
>>> tegra-pinmux-scripts applied when you generated the DT content for this
>>> patch?
>>
>>
>> Yes. Apart from my patch the top commit is 39af.
>
>
> OK, did you paste the same DT content into both DTs then, instead of generating each DT separately?
>
Not intentionally, but I wonder if I failed to change the board parameter?
> When I re-generate the DT using commit 39af, I don't get any changes to usb_vbus_en*.
I can't explain that. I'll try it again when I get a chance.
Regards,
Simon
^ permalink raw reply [flat|nested] 20+ messages in thread* [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
@ 2015-05-14 16:30 ` Simon Glass
0 siblings, 0 replies; 20+ messages in thread
From: Simon Glass @ 2015-05-14 16:30 UTC (permalink / raw)
To: linux-arm-kernel
Hi Stephen,
On 14 May 2015 at 09:47, Stephen Warren <swarren@wwwdotorg.org> wrote:
>
> On 05/14/2015 08:28 AM, Simon Glass wrote:
>>
>> Hi Stephen,
>>
>> On 14 May 2015 at 08:11, Stephen Warren <swarren@wwwdotorg.org> wrote:
>>>
>>> On 05/14/2015 07:09 AM, Tomeu Vizoso wrote:
>>>>
>>>>
>>>> On 13 May 2015 at 16:45, Stephen Warren <swarren@wwwdotorg.org> wrote:
>>>>>
>>>>>
>>>>> On 05/13/2015 08:13 AM, Simon Glass wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>> Regenerate the pinmux from the latest tegra-pinmux-scripts.
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> (Dropping most CCs; DT maintainers and lists generally don't get CC'd on
>>>>> simple DT content changes but rather on schema adds/changes and perhaps
>>>>> major DT content changes depending on context)
>>>>>
>>>>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts
>>>>>> b/arch/arm/boot/dts/tegra124-nyan-big.dts
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>> pinctrl-names = "default";
>>>>>> pinctrl-0 = <&pinmux_default>;
>>>>>>
>>>>>> - pinmux_default: common {
>>>>>> + state_default: pinmux {
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> This change will break compilation, since it changes the label name, yet
>>>>> the
>>>>> old name is still referenced in pinctrl-0 above. Same applies in the
>>>>> other
>>>>> file too.
>>>>>
>>>>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>>>>> b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>> @@ -437,18 +437,18 @@
>>>>>> usb_vbus_en0_pn4 {
>>>>>> nvidia,pins = "usb_vbus_en0_pn4";
>>>>>> nvidia,function = "usb";
>>>>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>>>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>>>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>>>>> nvidia,enable-input =
>>>>>> <TEGRA_PIN_ENABLE>;
>>>>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>>>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>>>>> };
>>>>>> usb_vbus_en1_pn5 {
>>>>>> nvidia,pins = "usb_vbus_en1_pn5";
>>>>>> nvidia,function = "usb";
>>>>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>>>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>>>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>>>>> nvidia,enable-input =
>>>>>> <TEGRA_PIN_ENABLE>;
>>>>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>>>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>>>>> };
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> Tomeu, can you comment on those changes? Evidently the pinmux
>>>>> configuration
>>>>> that's you added to the kernel doesn't exactly match the pinmux
>>>>> configuration that you added to tegra-pinmux-scripts.
>>>>
>>>>
>>>>
>>>> Are you sure? Just checked and what tegra-pinmux-scripts currently
>>>> generates matches what is currently in the kernel, for both nyans.
>>>
>>>
>>>
>>> My apologies; you're correct.
>>>
>>> This patch to the kernel DTs includes changes that aren't generated by
>>> either current tegra-pinmux-scripts, nor by tegra-pinmux-scripts with
>>> Simon's "[pinmux scripts PATCH] Support TPM on nyan boards" applied. Simon,
>>> can you double-check you didn't have any local patches to
>>> tegra-pinmux-scripts applied when you generated the DT content for this
>>> patch?
>>
>>
>> Yes. Apart from my patch the top commit is 39af.
>
>
> OK, did you paste the same DT content into both DTs then, instead of generating each DT separately?
>
Not intentionally, but I wonder if I failed to change the board parameter?
> When I re-generate the DT using commit 39af, I don't get any changes to usb_vbus_en*.
I can't explain that. I'll try it again when I get a chance.
Regards,
Simon
^ permalink raw reply [flat|nested] 20+ messages in thread[parent not found: <CAPnjgZ1o-DvWjJqkEjwbxKxx_0L7p1k8Mc58boqjHQEGh=yj3A-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>]
* Re: [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
2015-05-14 16:30 ` Simon Glass
@ 2015-07-03 23:06 ` Simon Glass
-1 siblings, 0 replies; 20+ messages in thread
From: Simon Glass @ 2015-07-03 23:06 UTC (permalink / raw)
To: Stephen Warren
Cc: Tomeu Vizoso, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Alexandre Courbot, Thierry Reding, Stephen Warren,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
Andrew Bresticker
Hi,
On 14 May 2015 at 10:30, Simon Glass <sjg-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org> wrote:
> Hi Stephen,
>
> On 14 May 2015 at 09:47, Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org> wrote:
>>
>> On 05/14/2015 08:28 AM, Simon Glass wrote:
>>>
>>> Hi Stephen,
>>>
>>> On 14 May 2015 at 08:11, Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org> wrote:
>>>>
>>>> On 05/14/2015 07:09 AM, Tomeu Vizoso wrote:
>>>>>
>>>>>
>>>>> On 13 May 2015 at 16:45, Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org> wrote:
>>>>>>
>>>>>>
>>>>>> On 05/13/2015 08:13 AM, Simon Glass wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> Regenerate the pinmux from the latest tegra-pinmux-scripts.
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> (Dropping most CCs; DT maintainers and lists generally don't get CC'd on
>>>>>> simple DT content changes but rather on schema adds/changes and perhaps
>>>>>> major DT content changes depending on context)
>>>>>>
>>>>>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts
>>>>>>> b/arch/arm/boot/dts/tegra124-nyan-big.dts
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>> pinctrl-names = "default";
>>>>>>> pinctrl-0 = <&pinmux_default>;
>>>>>>>
>>>>>>> - pinmux_default: common {
>>>>>>> + state_default: pinmux {
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> This change will break compilation, since it changes the label name, yet
>>>>>> the
>>>>>> old name is still referenced in pinctrl-0 above. Same applies in the
>>>>>> other
>>>>>> file too.
>>>>>>
>>>>>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>>>>>> b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>> @@ -437,18 +437,18 @@
>>>>>>> usb_vbus_en0_pn4 {
>>>>>>> nvidia,pins = "usb_vbus_en0_pn4";
>>>>>>> nvidia,function = "usb";
>>>>>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>>>>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>>>>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>>>>>> nvidia,enable-input =
>>>>>>> <TEGRA_PIN_ENABLE>;
>>>>>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>>>>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>>>>>> };
>>>>>>> usb_vbus_en1_pn5 {
>>>>>>> nvidia,pins = "usb_vbus_en1_pn5";
>>>>>>> nvidia,function = "usb";
>>>>>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>>>>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>>>>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>>>>>> nvidia,enable-input =
>>>>>>> <TEGRA_PIN_ENABLE>;
>>>>>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>>>>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>>>>>> };
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> Tomeu, can you comment on those changes? Evidently the pinmux
>>>>>> configuration
>>>>>> that's you added to the kernel doesn't exactly match the pinmux
>>>>>> configuration that you added to tegra-pinmux-scripts.
>>>>>
>>>>>
>>>>>
>>>>> Are you sure? Just checked and what tegra-pinmux-scripts currently
>>>>> generates matches what is currently in the kernel, for both nyans.
>>>>
>>>>
>>>>
>>>> My apologies; you're correct.
>>>>
>>>> This patch to the kernel DTs includes changes that aren't generated by
>>>> either current tegra-pinmux-scripts, nor by tegra-pinmux-scripts with
>>>> Simon's "[pinmux scripts PATCH] Support TPM on nyan boards" applied. Simon,
>>>> can you double-check you didn't have any local patches to
>>>> tegra-pinmux-scripts applied when you generated the DT content for this
>>>> patch?
>>>
>>>
>>> Yes. Apart from my patch the top commit is 39af.
>>
>>
>> OK, did you paste the same DT content into both DTs then, instead of generating each DT separately?
>>
>
> Not intentionally, but I wonder if I failed to change the board parameter?
>
>> When I re-generate the DT using commit 39af, I don't get any changes to usb_vbus_en*.
>
> I can't explain that. I'll try it again when I get a chance.
It doesn't seem to happen now, I must have done something wrong.
I'll send a v2 patch.
Regards,
Simon
^ permalink raw reply [flat|nested] 20+ messages in thread* [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards
@ 2015-07-03 23:06 ` Simon Glass
0 siblings, 0 replies; 20+ messages in thread
From: Simon Glass @ 2015-07-03 23:06 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On 14 May 2015 at 10:30, Simon Glass <sjg@chromium.org> wrote:
> Hi Stephen,
>
> On 14 May 2015 at 09:47, Stephen Warren <swarren@wwwdotorg.org> wrote:
>>
>> On 05/14/2015 08:28 AM, Simon Glass wrote:
>>>
>>> Hi Stephen,
>>>
>>> On 14 May 2015 at 08:11, Stephen Warren <swarren@wwwdotorg.org> wrote:
>>>>
>>>> On 05/14/2015 07:09 AM, Tomeu Vizoso wrote:
>>>>>
>>>>>
>>>>> On 13 May 2015 at 16:45, Stephen Warren <swarren@wwwdotorg.org> wrote:
>>>>>>
>>>>>>
>>>>>> On 05/13/2015 08:13 AM, Simon Glass wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> Regenerate the pinmux from the latest tegra-pinmux-scripts.
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> (Dropping most CCs; DT maintainers and lists generally don't get CC'd on
>>>>>> simple DT content changes but rather on schema adds/changes and perhaps
>>>>>> major DT content changes depending on context)
>>>>>>
>>>>>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts
>>>>>>> b/arch/arm/boot/dts/tegra124-nyan-big.dts
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>> pinctrl-names = "default";
>>>>>>> pinctrl-0 = <&pinmux_default>;
>>>>>>>
>>>>>>> - pinmux_default: common {
>>>>>>> + state_default: pinmux {
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> This change will break compilation, since it changes the label name, yet
>>>>>> the
>>>>>> old name is still referenced in pinctrl-0 above. Same applies in the
>>>>>> other
>>>>>> file too.
>>>>>>
>>>>>>> diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>>>>>> b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>> @@ -437,18 +437,18 @@
>>>>>>> usb_vbus_en0_pn4 {
>>>>>>> nvidia,pins = "usb_vbus_en0_pn4";
>>>>>>> nvidia,function = "usb";
>>>>>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>>>>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>>>>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>>>>>> nvidia,enable-input =
>>>>>>> <TEGRA_PIN_ENABLE>;
>>>>>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>>>>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>>>>>> };
>>>>>>> usb_vbus_en1_pn5 {
>>>>>>> nvidia,pins = "usb_vbus_en1_pn5";
>>>>>>> nvidia,function = "usb";
>>>>>>> - nvidia,pull = <TEGRA_PIN_PULL_UP>;
>>>>>>> + nvidia,pull = <TEGRA_PIN_PULL_NONE>;
>>>>>>> nvidia,tristate = <TEGRA_PIN_DISABLE>;
>>>>>>> nvidia,enable-input =
>>>>>>> <TEGRA_PIN_ENABLE>;
>>>>>>> - nvidia,open-drain = <TEGRA_PIN_DISABLE>;
>>>>>>> + nvidia,open-drain = <TEGRA_PIN_ENABLE>;
>>>>>>> };
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> Tomeu, can you comment on those changes? Evidently the pinmux
>>>>>> configuration
>>>>>> that's you added to the kernel doesn't exactly match the pinmux
>>>>>> configuration that you added to tegra-pinmux-scripts.
>>>>>
>>>>>
>>>>>
>>>>> Are you sure? Just checked and what tegra-pinmux-scripts currently
>>>>> generates matches what is currently in the kernel, for both nyans.
>>>>
>>>>
>>>>
>>>> My apologies; you're correct.
>>>>
>>>> This patch to the kernel DTs includes changes that aren't generated by
>>>> either current tegra-pinmux-scripts, nor by tegra-pinmux-scripts with
>>>> Simon's "[pinmux scripts PATCH] Support TPM on nyan boards" applied. Simon,
>>>> can you double-check you didn't have any local patches to
>>>> tegra-pinmux-scripts applied when you generated the DT content for this
>>>> patch?
>>>
>>>
>>> Yes. Apart from my patch the top commit is 39af.
>>
>>
>> OK, did you paste the same DT content into both DTs then, instead of generating each DT separately?
>>
>
> Not intentionally, but I wonder if I failed to change the board parameter?
>
>> When I re-generate the DT using commit 39af, I don't get any changes to usb_vbus_en*.
>
> I can't explain that. I'll try it again when I get a chance.
It doesn't seem to happen now, I must have done something wrong.
I'll send a v2 patch.
Regards,
Simon
^ permalink raw reply [flat|nested] 20+ messages in thread
end of thread, other threads:[~2015-07-03 23:06 UTC | newest]
Thread overview: 20+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2015-05-13 14:13 [PATCH] ARM: tegra: Enable TPM on tegra124 nyan boards Simon Glass
2015-05-13 14:13 ` Simon Glass
[not found] ` <1431526427-13340-1-git-send-email-sjg-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>
2015-05-13 14:45 ` Stephen Warren
2015-05-13 14:45 ` Stephen Warren
[not found] ` <5553637C.5010506-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org>
2015-05-13 15:22 ` Simon Glass
2015-05-13 15:22 ` Simon Glass
[not found] ` <CAPnjgZ0ga6==w7YWQoeUtXRxUhCjQ+BHMJuCL7vbqN9WTLM2kQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2015-05-14 14:21 ` Stephen Warren
2015-05-14 14:21 ` Stephen Warren
2015-05-14 13:09 ` Tomeu Vizoso
2015-05-14 13:09 ` Tomeu Vizoso
[not found] ` <CAAObsKCxFJA=6kyHM5rtpJMVRZRDbBO3KSn+QdNoOQz1rXCWTQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2015-05-14 14:11 ` Stephen Warren
2015-05-14 14:11 ` Stephen Warren
[not found] ` <5554AD0B.1060106-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org>
2015-05-14 14:28 ` Simon Glass
2015-05-14 14:28 ` Simon Glass
[not found] ` <CAPnjgZ2QrTu=D_AapTded+_NR1waZTbNoN8rCtHnTdd0OdnwLA-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2015-05-14 15:47 ` Stephen Warren
2015-05-14 15:47 ` Stephen Warren
[not found] ` <5554C399.4060807-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org>
2015-05-14 16:30 ` Simon Glass
2015-05-14 16:30 ` Simon Glass
[not found] ` <CAPnjgZ1o-DvWjJqkEjwbxKxx_0L7p1k8Mc58boqjHQEGh=yj3A-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2015-07-03 23:06 ` Simon Glass
2015-07-03 23:06 ` Simon Glass
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.