From: Zhou Wang <wangzhou1@hisilicon.com>
To: James Morse <james.morse@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>,
Jingoo Han <jg1.han@samsung.com>,
Pratyush Anand <pratyush.anand@gmail.com>,
Arnd Bergmann <arnd@arndb.de>,
"fabrice.gasnier@st.com" <fabrice.gasnier@st.com>,
Liviu Dudau <Liviu.Dudau@arm.com>,
"linux-pci@vger.kernel.org" <linux-pci@vger.kernel.org>,
"linux-arm-kernel@lists.infradead.org"
<linux-arm-kernel@lists.infradead.org>,
"devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
"gabriele.paoloni@huawei.com" <gabriele.paoloni@huawei.com>,
"yuanzhichang@hisilicon.com" <yuanzhichang@hisilicon.com>,
"zhudacai@hisilicon.com" <zhudacai@hisilicon.com>,
"zhangjukuo@huawei.com" <zhangjukuo@huawei.com>,
"qiuzhenfa@hisilicon.com" <qiuzhenfa@hisilicon.com>,
"liguozhu@hisilicon.com" <liguozhu@hisilicon.com>
Subject: Re: [PATCH v2 2/4] PCI: designware: Add ARM64 support
Date: Thu, 11 Jun 2015 10:44:53 +0800 [thread overview]
Message-ID: <5578F625.1090305@hisilicon.com> (raw)
In-Reply-To: <5570507F.4030704@arm.com>
On 2015/6/4 21:19, James Morse wrote:
> On 03/06/15 09:35, Zhou Wang wrote:
>> This patch tries to unify ARM32 and ARM64 PCIe in designware driver. Delete
>> function dw_pcie_setup, dw_pcie_scan_bus, dw_pcie_map_irq and struct hw_pci,
>> move related operations to dw_pcie_host_init. Also set pp->root_bus_nr = 0 in
>> each PCIe host driver which is based on pcie-designware.
>>
>> I am not very clear about I/O resource management:
>>> if (global_io_offset < SZ_1M && pp->io_size > 0) {
>>> pci_ioremap_io(global_io_offset, pp->io_base);
>>> global_io_offset += SZ_64K;
>>> pci_add_resource_offset(&res, &pp->io,
>>> global_io_offset - pp->io_bus_addr);
>>> }
>> so just move steps in dw_pcie_setup to dw_pcie_host_init.
>>
>> I have compiled the driver with multi_v7_defconfig. However, I don't have
>> ARM32 PCIe related board to do test. It will be appreciated if someone could
>> help to test it.
>
> I have tested this on a 'Freescale i.MX6 Quad SABRE Lite Board', which also
> uses a designware pcie host controller (PCI_IMX6). Booted,
> removed/rescanned the bus, then scanned for wireless access points using
> the b43 driver. Please note my change below.
>
> Tested-by: James Morse <james.morse@arm.com>
>
>> diff --git a/drivers/pci/host/pcie-designware.c b/drivers/pci/host/pcie-designware.c
>> index 2e9f84f..b3f0ac7 100644
>> --- a/drivers/pci/host/pcie-designware.c
>> +++ b/drivers/pci/host/pcie-designware.c
>> @@ -11,6 +11,7 @@
>> * published by the Free Software Foundation.
>> */
>>
>> +#include <linux/hardirq.h>
>> #include <linux/irq.h>
>> #include <linux/irqdomain.h>
>> #include <linux/kernel.h>
>> @@ -67,17 +68,10 @@
>> #define PCIE_ATU_FUNC(x) (((x) & 0x7) << 16)
>> #define PCIE_ATU_UPPER_TARGET 0x91C
>>
>> -static struct hw_pci dw_pci;
>> +static struct pci_ops dw_pcie_ops;
>>
>> static unsigned long global_io_offset;
>>
>> -static inline struct pcie_port *sys_to_pcie(struct pci_sys_data *sys)
>> -{
>> - BUG_ON(!sys->private_data);
>> -
>> - return sys->private_data;
>> -}
>> -
>> int dw_pcie_cfg_read(void __iomem *addr, int where, int size, u32 *val)
>> {
>> *val = readl(addr);
>> @@ -238,7 +232,7 @@ static void dw_pcie_msi_set_irq(struct pcie_port *pp, int irq)
>> static int assign_irq(int no_irqs, struct msi_desc *desc, int *pos)
>> {
>> int irq, pos0, i;
>> - struct pcie_port *pp = sys_to_pcie(desc->dev->bus->sysdata);
>> + struct pcie_port *pp = desc->dev->bus->sysdata;
>>
>> pos0 = bitmap_find_free_region(pp->msi_irq_in_use, MAX_MSI_IRQS,
>> order_base_2(no_irqs));
>> @@ -281,7 +275,7 @@ static int dw_msi_setup_irq(struct msi_controller *chip, struct pci_dev *pdev,
>> {
>> int irq, pos;
>> struct msi_msg msg;
>> - struct pcie_port *pp = sys_to_pcie(pdev->bus->sysdata);
>> + struct pcie_port *pp = pdev->bus->sysdata;
>>
>> if (desc->msi_attrib.is_msix)
>> return -EINVAL;
>> @@ -310,7 +304,7 @@ static void dw_msi_teardown_irq(struct msi_controller *chip, unsigned int irq)
>> {
>> struct irq_data *data = irq_get_irq_data(irq);
>> struct msi_desc *msi = irq_data_get_msi(data);
>> - struct pcie_port *pp = sys_to_pcie(msi->dev->bus->sysdata);
>> + struct pcie_port *pp = msi->dev->bus->sysdata;
>>
>> clear_irq_range(pp, irq, 1, data->hwirq);
>> }
>> @@ -342,13 +336,15 @@ static const struct irq_domain_ops msi_domain_ops = {
>> .map = dw_pcie_msi_map,
>> };
>>
>> -int dw_pcie_host_init(struct pcie_port *pp)
>> +int __init dw_pcie_host_init(struct pcie_port *pp)
>> {
>> struct device_node *np = pp->dev->of_node;
>> struct platform_device *pdev = to_platform_device(pp->dev);
>> struct of_pci_range range;
>> struct of_pci_range_parser parser;
>> + struct pci_bus *bus;
>> struct resource *cfg_res;
>> + LIST_HEAD(res);
>> u32 val, na, ns;
>> const __be32 *addrp;
>> int i, index, ret;
>> @@ -502,15 +498,49 @@ int dw_pcie_host_init(struct pcie_port *pp)
>> val |= PORT_LOGIC_SPEED_CHANGE;
>> dw_pcie_wr_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, val);
>>
>> -#ifdef CONFIG_PCI_MSI
>> - dw_pcie_msi_chip.dev = pp->dev;
>> - dw_pci.msi_ctrl = &dw_pcie_msi_chip;
>> +#ifdef CONFIG_ARM
>> + /*
>> + * FIXME: we should really be able to use
>> + * of_pci_get_host_bridge_resources on arm32 as well,
>> + * but the conversion needs some more testing
>> + */
>> + if (global_io_offset < SZ_1M && pp->io_size > 0) {
>> + pci_ioremap_io(global_io_offset, pp->io_base);
>> + global_io_offset += SZ_64K;
>> + pci_add_resource_offset(&res, &pp->io,
>> + global_io_offset - pp->io_bus_addr);
>> + }
>> + pci_add_resource_offset(&res, &pp->mem,
>> + pp->mem.start - pp->mem_bus_addr);
>> + pci_add_resource(&res, &pp->busn);
>
> I don't think this #ifdef is necessary. In the spirit of 'the conversion
> needs some more testing', I removed it leaving just the below arm64 code.
>
> This worked on my Freescale i.MX6 Quad SABRE Lite Board, I went as far as
> scanning for wireless access points.
>
>
Hi James,
I think you are right. We can remove #ifdef as of_pci_get_host_bridge_resources
also manages mem, io and bus resources.
And just as Lorenzo said, if we want PCIe cards with IO bar work well,
pci_remap_iospace should be added after of_pci_get_host_bridge_resources to map
IO cpu address to PCI_IOBASE.
Thanks again for your test :)
Zhou
>> +#else
>> + ret = of_pci_get_host_bridge_resources(np, 0, 0xff, &res, &pp->io_base);
>
> of_pci_get_host_bridge_resources expects &pp->io_base to be a
> resource_size_t*, but &io_base is u64*. This generates a warning on arm
> with the above change. Changing the the type in
> drivers/pci/host/pcie-designware.h fixes this.
>
>
> Thanks,
>
> James
>
>> + if (ret)
>> + return ret;
>> +#endif
>> +
>> + bus = pci_create_root_bus(pp->dev, pp->root_bus_nr, &dw_pcie_ops,
>> + pp, &res);
>> + if (!bus)
>> + return -ENOMEM;
>> +
>> +#ifdef CONFIG_GENERIC_MSI_IRQ_DOMAIN
>> + bus->msi = container_of(&pp->irq_domain, struct msi_controller, domain);
>> +#else
>> + bus->msi = &dw_pcie_msi_chip;
>> #endif
>>
>> - dw_pci.nr_controllers = 1;
>> - dw_pci.private_data = (void **)&pp;
>> + pci_scan_child_bus(bus);
>> + if (pp->ops->scan_bus)
>> + pp->ops->scan_bus(pp);
>>
>> - pci_common_init_dev(pp->dev, &dw_pci);
>> +#ifdef CONFIG_ARM
>> + /* support old dtbs that incorrectly describe IRQs */
>> + pci_fixup_irqs(pci_common_swizzle, of_irq_parse_and_map_pci);
>> +#endif
>> +
>> + pci_assign_unassigned_bus_resources(bus);
>> + pci_bus_add_devices(bus);
>>
>> return 0;
>> }
>> @@ -653,7 +683,7 @@ static int dw_pcie_valid_config(struct pcie_port *pp,
>> static int dw_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where,
>> int size, u32 *val)
>> {
>> - struct pcie_port *pp = sys_to_pcie(bus->sysdata);
>> + struct pcie_port *pp = bus->sysdata;
>> int ret;
>>
>> if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0) {
>> @@ -677,7 +707,7 @@ static int dw_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where,
>> static int dw_pcie_wr_conf(struct pci_bus *bus, u32 devfn,
>> int where, int size, u32 val)
>> {
>> - struct pcie_port *pp = sys_to_pcie(bus->sysdata);
>> + struct pcie_port *pp = bus->sysdata;
>> int ret;
>>
>> if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0)
>> @@ -701,64 +731,6 @@ static struct pci_ops dw_pcie_ops = {
>> .write = dw_pcie_wr_conf,
>> };
>>
>> -static int dw_pcie_setup(int nr, struct pci_sys_data *sys)
>> -{
>> - struct pcie_port *pp;
>> -
>> - pp = sys_to_pcie(sys);
>> -
>> - if (global_io_offset < SZ_1M && pp->io_size > 0) {
>> - sys->io_offset = global_io_offset - pp->io_bus_addr;
>> - pci_ioremap_io(global_io_offset, pp->io_base);
>> - global_io_offset += SZ_64K;
>> - pci_add_resource_offset(&sys->resources, &pp->io,
>> - sys->io_offset);
>> - }
>> -
>> - sys->mem_offset = pp->mem.start - pp->mem_bus_addr;
>> - pci_add_resource_offset(&sys->resources, &pp->mem, sys->mem_offset);
>> - pci_add_resource(&sys->resources, &pp->busn);
>> -
>> - return 1;
>> -}
>> -
>> -static struct pci_bus *dw_pcie_scan_bus(int nr, struct pci_sys_data *sys)
>> -{
>> - struct pci_bus *bus;
>> - struct pcie_port *pp = sys_to_pcie(sys);
>> -
>> - pp->root_bus_nr = sys->busnr;
>> - bus = pci_create_root_bus(pp->dev, sys->busnr,
>> - &dw_pcie_ops, sys, &sys->resources);
>> - if (!bus)
>> - return NULL;
>> -
>> - pci_scan_child_bus(bus);
>> -
>> - if (bus && pp->ops->scan_bus)
>> - pp->ops->scan_bus(pp);
>> -
>> - return bus;
>> -}
>> -
>> -static int dw_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
>> -{
>> - struct pcie_port *pp = sys_to_pcie(dev->bus->sysdata);
>> - int irq;
>> -
>> - irq = of_irq_parse_and_map_pci(dev, slot, pin);
>> - if (!irq)
>> - irq = pp->irq;
>> -
>> - return irq;
>> -}
>> -
>> -static struct hw_pci dw_pci = {
>> - .setup = dw_pcie_setup,
>> - .scan = dw_pcie_scan_bus,
>> - .map_irq = dw_pcie_map_irq,
>> -};
>> -
>> void dw_pcie_setup_rc(struct pcie_port *pp)
>> {
>> u32 val;
>
>
> .
>
WARNING: multiple messages have this Message-ID (diff)
From: wangzhou1@hisilicon.com (Zhou Wang)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 2/4] PCI: designware: Add ARM64 support
Date: Thu, 11 Jun 2015 10:44:53 +0800 [thread overview]
Message-ID: <5578F625.1090305@hisilicon.com> (raw)
In-Reply-To: <5570507F.4030704@arm.com>
On 2015/6/4 21:19, James Morse wrote:
> On 03/06/15 09:35, Zhou Wang wrote:
>> This patch tries to unify ARM32 and ARM64 PCIe in designware driver. Delete
>> function dw_pcie_setup, dw_pcie_scan_bus, dw_pcie_map_irq and struct hw_pci,
>> move related operations to dw_pcie_host_init. Also set pp->root_bus_nr = 0 in
>> each PCIe host driver which is based on pcie-designware.
>>
>> I am not very clear about I/O resource management:
>>> if (global_io_offset < SZ_1M && pp->io_size > 0) {
>>> pci_ioremap_io(global_io_offset, pp->io_base);
>>> global_io_offset += SZ_64K;
>>> pci_add_resource_offset(&res, &pp->io,
>>> global_io_offset - pp->io_bus_addr);
>>> }
>> so just move steps in dw_pcie_setup to dw_pcie_host_init.
>>
>> I have compiled the driver with multi_v7_defconfig. However, I don't have
>> ARM32 PCIe related board to do test. It will be appreciated if someone could
>> help to test it.
>
> I have tested this on a 'Freescale i.MX6 Quad SABRE Lite Board', which also
> uses a designware pcie host controller (PCI_IMX6). Booted,
> removed/rescanned the bus, then scanned for wireless access points using
> the b43 driver. Please note my change below.
>
> Tested-by: James Morse <james.morse@arm.com>
>
>> diff --git a/drivers/pci/host/pcie-designware.c b/drivers/pci/host/pcie-designware.c
>> index 2e9f84f..b3f0ac7 100644
>> --- a/drivers/pci/host/pcie-designware.c
>> +++ b/drivers/pci/host/pcie-designware.c
>> @@ -11,6 +11,7 @@
>> * published by the Free Software Foundation.
>> */
>>
>> +#include <linux/hardirq.h>
>> #include <linux/irq.h>
>> #include <linux/irqdomain.h>
>> #include <linux/kernel.h>
>> @@ -67,17 +68,10 @@
>> #define PCIE_ATU_FUNC(x) (((x) & 0x7) << 16)
>> #define PCIE_ATU_UPPER_TARGET 0x91C
>>
>> -static struct hw_pci dw_pci;
>> +static struct pci_ops dw_pcie_ops;
>>
>> static unsigned long global_io_offset;
>>
>> -static inline struct pcie_port *sys_to_pcie(struct pci_sys_data *sys)
>> -{
>> - BUG_ON(!sys->private_data);
>> -
>> - return sys->private_data;
>> -}
>> -
>> int dw_pcie_cfg_read(void __iomem *addr, int where, int size, u32 *val)
>> {
>> *val = readl(addr);
>> @@ -238,7 +232,7 @@ static void dw_pcie_msi_set_irq(struct pcie_port *pp, int irq)
>> static int assign_irq(int no_irqs, struct msi_desc *desc, int *pos)
>> {
>> int irq, pos0, i;
>> - struct pcie_port *pp = sys_to_pcie(desc->dev->bus->sysdata);
>> + struct pcie_port *pp = desc->dev->bus->sysdata;
>>
>> pos0 = bitmap_find_free_region(pp->msi_irq_in_use, MAX_MSI_IRQS,
>> order_base_2(no_irqs));
>> @@ -281,7 +275,7 @@ static int dw_msi_setup_irq(struct msi_controller *chip, struct pci_dev *pdev,
>> {
>> int irq, pos;
>> struct msi_msg msg;
>> - struct pcie_port *pp = sys_to_pcie(pdev->bus->sysdata);
>> + struct pcie_port *pp = pdev->bus->sysdata;
>>
>> if (desc->msi_attrib.is_msix)
>> return -EINVAL;
>> @@ -310,7 +304,7 @@ static void dw_msi_teardown_irq(struct msi_controller *chip, unsigned int irq)
>> {
>> struct irq_data *data = irq_get_irq_data(irq);
>> struct msi_desc *msi = irq_data_get_msi(data);
>> - struct pcie_port *pp = sys_to_pcie(msi->dev->bus->sysdata);
>> + struct pcie_port *pp = msi->dev->bus->sysdata;
>>
>> clear_irq_range(pp, irq, 1, data->hwirq);
>> }
>> @@ -342,13 +336,15 @@ static const struct irq_domain_ops msi_domain_ops = {
>> .map = dw_pcie_msi_map,
>> };
>>
>> -int dw_pcie_host_init(struct pcie_port *pp)
>> +int __init dw_pcie_host_init(struct pcie_port *pp)
>> {
>> struct device_node *np = pp->dev->of_node;
>> struct platform_device *pdev = to_platform_device(pp->dev);
>> struct of_pci_range range;
>> struct of_pci_range_parser parser;
>> + struct pci_bus *bus;
>> struct resource *cfg_res;
>> + LIST_HEAD(res);
>> u32 val, na, ns;
>> const __be32 *addrp;
>> int i, index, ret;
>> @@ -502,15 +498,49 @@ int dw_pcie_host_init(struct pcie_port *pp)
>> val |= PORT_LOGIC_SPEED_CHANGE;
>> dw_pcie_wr_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, val);
>>
>> -#ifdef CONFIG_PCI_MSI
>> - dw_pcie_msi_chip.dev = pp->dev;
>> - dw_pci.msi_ctrl = &dw_pcie_msi_chip;
>> +#ifdef CONFIG_ARM
>> + /*
>> + * FIXME: we should really be able to use
>> + * of_pci_get_host_bridge_resources on arm32 as well,
>> + * but the conversion needs some more testing
>> + */
>> + if (global_io_offset < SZ_1M && pp->io_size > 0) {
>> + pci_ioremap_io(global_io_offset, pp->io_base);
>> + global_io_offset += SZ_64K;
>> + pci_add_resource_offset(&res, &pp->io,
>> + global_io_offset - pp->io_bus_addr);
>> + }
>> + pci_add_resource_offset(&res, &pp->mem,
>> + pp->mem.start - pp->mem_bus_addr);
>> + pci_add_resource(&res, &pp->busn);
>
> I don't think this #ifdef is necessary. In the spirit of 'the conversion
> needs some more testing', I removed it leaving just the below arm64 code.
>
> This worked on my Freescale i.MX6 Quad SABRE Lite Board, I went as far as
> scanning for wireless access points.
>
>
Hi James,
I think you are right. We can remove #ifdef as of_pci_get_host_bridge_resources
also manages mem, io and bus resources.
And just as Lorenzo said, if we want PCIe cards with IO bar work well,
pci_remap_iospace should be added after of_pci_get_host_bridge_resources to map
IO cpu address to PCI_IOBASE.
Thanks again for your test :)
Zhou
>> +#else
>> + ret = of_pci_get_host_bridge_resources(np, 0, 0xff, &res, &pp->io_base);
>
> of_pci_get_host_bridge_resources expects &pp->io_base to be a
> resource_size_t*, but &io_base is u64*. This generates a warning on arm
> with the above change. Changing the the type in
> drivers/pci/host/pcie-designware.h fixes this.
>
>
> Thanks,
>
> James
>
>> + if (ret)
>> + return ret;
>> +#endif
>> +
>> + bus = pci_create_root_bus(pp->dev, pp->root_bus_nr, &dw_pcie_ops,
>> + pp, &res);
>> + if (!bus)
>> + return -ENOMEM;
>> +
>> +#ifdef CONFIG_GENERIC_MSI_IRQ_DOMAIN
>> + bus->msi = container_of(&pp->irq_domain, struct msi_controller, domain);
>> +#else
>> + bus->msi = &dw_pcie_msi_chip;
>> #endif
>>
>> - dw_pci.nr_controllers = 1;
>> - dw_pci.private_data = (void **)&pp;
>> + pci_scan_child_bus(bus);
>> + if (pp->ops->scan_bus)
>> + pp->ops->scan_bus(pp);
>>
>> - pci_common_init_dev(pp->dev, &dw_pci);
>> +#ifdef CONFIG_ARM
>> + /* support old dtbs that incorrectly describe IRQs */
>> + pci_fixup_irqs(pci_common_swizzle, of_irq_parse_and_map_pci);
>> +#endif
>> +
>> + pci_assign_unassigned_bus_resources(bus);
>> + pci_bus_add_devices(bus);
>>
>> return 0;
>> }
>> @@ -653,7 +683,7 @@ static int dw_pcie_valid_config(struct pcie_port *pp,
>> static int dw_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where,
>> int size, u32 *val)
>> {
>> - struct pcie_port *pp = sys_to_pcie(bus->sysdata);
>> + struct pcie_port *pp = bus->sysdata;
>> int ret;
>>
>> if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0) {
>> @@ -677,7 +707,7 @@ static int dw_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where,
>> static int dw_pcie_wr_conf(struct pci_bus *bus, u32 devfn,
>> int where, int size, u32 val)
>> {
>> - struct pcie_port *pp = sys_to_pcie(bus->sysdata);
>> + struct pcie_port *pp = bus->sysdata;
>> int ret;
>>
>> if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0)
>> @@ -701,64 +731,6 @@ static struct pci_ops dw_pcie_ops = {
>> .write = dw_pcie_wr_conf,
>> };
>>
>> -static int dw_pcie_setup(int nr, struct pci_sys_data *sys)
>> -{
>> - struct pcie_port *pp;
>> -
>> - pp = sys_to_pcie(sys);
>> -
>> - if (global_io_offset < SZ_1M && pp->io_size > 0) {
>> - sys->io_offset = global_io_offset - pp->io_bus_addr;
>> - pci_ioremap_io(global_io_offset, pp->io_base);
>> - global_io_offset += SZ_64K;
>> - pci_add_resource_offset(&sys->resources, &pp->io,
>> - sys->io_offset);
>> - }
>> -
>> - sys->mem_offset = pp->mem.start - pp->mem_bus_addr;
>> - pci_add_resource_offset(&sys->resources, &pp->mem, sys->mem_offset);
>> - pci_add_resource(&sys->resources, &pp->busn);
>> -
>> - return 1;
>> -}
>> -
>> -static struct pci_bus *dw_pcie_scan_bus(int nr, struct pci_sys_data *sys)
>> -{
>> - struct pci_bus *bus;
>> - struct pcie_port *pp = sys_to_pcie(sys);
>> -
>> - pp->root_bus_nr = sys->busnr;
>> - bus = pci_create_root_bus(pp->dev, sys->busnr,
>> - &dw_pcie_ops, sys, &sys->resources);
>> - if (!bus)
>> - return NULL;
>> -
>> - pci_scan_child_bus(bus);
>> -
>> - if (bus && pp->ops->scan_bus)
>> - pp->ops->scan_bus(pp);
>> -
>> - return bus;
>> -}
>> -
>> -static int dw_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
>> -{
>> - struct pcie_port *pp = sys_to_pcie(dev->bus->sysdata);
>> - int irq;
>> -
>> - irq = of_irq_parse_and_map_pci(dev, slot, pin);
>> - if (!irq)
>> - irq = pp->irq;
>> -
>> - return irq;
>> -}
>> -
>> -static struct hw_pci dw_pci = {
>> - .setup = dw_pcie_setup,
>> - .scan = dw_pcie_scan_bus,
>> - .map_irq = dw_pcie_map_irq,
>> -};
>> -
>> void dw_pcie_setup_rc(struct pcie_port *pp)
>> {
>> u32 val;
>
>
> .
>
WARNING: multiple messages have this Message-ID (diff)
From: Zhou Wang <wangzhou1-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org>
To: James Morse <james.morse-5wv7dgnIgG8@public.gmane.org>
Cc: Bjorn Helgaas <bhelgaas-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org>,
Jingoo Han <jg1.han-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>,
Pratyush Anand
<pratyush.anand-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>,
Arnd Bergmann <arnd-r2nGTMty4D4@public.gmane.org>,
"fabrice.gasnier-qxv4g6HH51o@public.gmane.org"
<fabrice.gasnier-qxv4g6HH51o@public.gmane.org>,
Liviu Dudau <Liviu.Dudau-5wv7dgnIgG8@public.gmane.org>,
"linux-pci-u79uwXL29TY76Z2rM5mHXA@public.gmane.org"
<linux-pci-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>,
"linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org"
<linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org>,
"devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org"
<devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>,
"gabriele.paoloni-hv44wF8Li93QT0dZR+AlfA@public.gmane.org"
<gabriele.paoloni-hv44wF8Li93QT0dZR+AlfA@public.gmane.org>,
"yuanzhichang-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org"
<yuanzhichang-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org>,
"zhudacai-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org"
<zhudacai-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org>,
"zhangjukuo-hv44wF8Li93QT0dZR+AlfA@public.gmane.org"
<zhangjukuo-hv44wF8Li93QT0dZR+AlfA@public.gmane.org>,
"qiuzhenfa-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org"
<qiuzhenfa-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org>,
"liguozhu-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org"
<liguozhu-C8/M+/jPZTeaMJb+Lgu22Q@public.gmane.org>
Subject: Re: [PATCH v2 2/4] PCI: designware: Add ARM64 support
Date: Thu, 11 Jun 2015 10:44:53 +0800 [thread overview]
Message-ID: <5578F625.1090305@hisilicon.com> (raw)
In-Reply-To: <5570507F.4030704-5wv7dgnIgG8@public.gmane.org>
On 2015/6/4 21:19, James Morse wrote:
> On 03/06/15 09:35, Zhou Wang wrote:
>> This patch tries to unify ARM32 and ARM64 PCIe in designware driver. Delete
>> function dw_pcie_setup, dw_pcie_scan_bus, dw_pcie_map_irq and struct hw_pci,
>> move related operations to dw_pcie_host_init. Also set pp->root_bus_nr = 0 in
>> each PCIe host driver which is based on pcie-designware.
>>
>> I am not very clear about I/O resource management:
>>> if (global_io_offset < SZ_1M && pp->io_size > 0) {
>>> pci_ioremap_io(global_io_offset, pp->io_base);
>>> global_io_offset += SZ_64K;
>>> pci_add_resource_offset(&res, &pp->io,
>>> global_io_offset - pp->io_bus_addr);
>>> }
>> so just move steps in dw_pcie_setup to dw_pcie_host_init.
>>
>> I have compiled the driver with multi_v7_defconfig. However, I don't have
>> ARM32 PCIe related board to do test. It will be appreciated if someone could
>> help to test it.
>
> I have tested this on a 'Freescale i.MX6 Quad SABRE Lite Board', which also
> uses a designware pcie host controller (PCI_IMX6). Booted,
> removed/rescanned the bus, then scanned for wireless access points using
> the b43 driver. Please note my change below.
>
> Tested-by: James Morse <james.morse-5wv7dgnIgG8@public.gmane.org>
>
>> diff --git a/drivers/pci/host/pcie-designware.c b/drivers/pci/host/pcie-designware.c
>> index 2e9f84f..b3f0ac7 100644
>> --- a/drivers/pci/host/pcie-designware.c
>> +++ b/drivers/pci/host/pcie-designware.c
>> @@ -11,6 +11,7 @@
>> * published by the Free Software Foundation.
>> */
>>
>> +#include <linux/hardirq.h>
>> #include <linux/irq.h>
>> #include <linux/irqdomain.h>
>> #include <linux/kernel.h>
>> @@ -67,17 +68,10 @@
>> #define PCIE_ATU_FUNC(x) (((x) & 0x7) << 16)
>> #define PCIE_ATU_UPPER_TARGET 0x91C
>>
>> -static struct hw_pci dw_pci;
>> +static struct pci_ops dw_pcie_ops;
>>
>> static unsigned long global_io_offset;
>>
>> -static inline struct pcie_port *sys_to_pcie(struct pci_sys_data *sys)
>> -{
>> - BUG_ON(!sys->private_data);
>> -
>> - return sys->private_data;
>> -}
>> -
>> int dw_pcie_cfg_read(void __iomem *addr, int where, int size, u32 *val)
>> {
>> *val = readl(addr);
>> @@ -238,7 +232,7 @@ static void dw_pcie_msi_set_irq(struct pcie_port *pp, int irq)
>> static int assign_irq(int no_irqs, struct msi_desc *desc, int *pos)
>> {
>> int irq, pos0, i;
>> - struct pcie_port *pp = sys_to_pcie(desc->dev->bus->sysdata);
>> + struct pcie_port *pp = desc->dev->bus->sysdata;
>>
>> pos0 = bitmap_find_free_region(pp->msi_irq_in_use, MAX_MSI_IRQS,
>> order_base_2(no_irqs));
>> @@ -281,7 +275,7 @@ static int dw_msi_setup_irq(struct msi_controller *chip, struct pci_dev *pdev,
>> {
>> int irq, pos;
>> struct msi_msg msg;
>> - struct pcie_port *pp = sys_to_pcie(pdev->bus->sysdata);
>> + struct pcie_port *pp = pdev->bus->sysdata;
>>
>> if (desc->msi_attrib.is_msix)
>> return -EINVAL;
>> @@ -310,7 +304,7 @@ static void dw_msi_teardown_irq(struct msi_controller *chip, unsigned int irq)
>> {
>> struct irq_data *data = irq_get_irq_data(irq);
>> struct msi_desc *msi = irq_data_get_msi(data);
>> - struct pcie_port *pp = sys_to_pcie(msi->dev->bus->sysdata);
>> + struct pcie_port *pp = msi->dev->bus->sysdata;
>>
>> clear_irq_range(pp, irq, 1, data->hwirq);
>> }
>> @@ -342,13 +336,15 @@ static const struct irq_domain_ops msi_domain_ops = {
>> .map = dw_pcie_msi_map,
>> };
>>
>> -int dw_pcie_host_init(struct pcie_port *pp)
>> +int __init dw_pcie_host_init(struct pcie_port *pp)
>> {
>> struct device_node *np = pp->dev->of_node;
>> struct platform_device *pdev = to_platform_device(pp->dev);
>> struct of_pci_range range;
>> struct of_pci_range_parser parser;
>> + struct pci_bus *bus;
>> struct resource *cfg_res;
>> + LIST_HEAD(res);
>> u32 val, na, ns;
>> const __be32 *addrp;
>> int i, index, ret;
>> @@ -502,15 +498,49 @@ int dw_pcie_host_init(struct pcie_port *pp)
>> val |= PORT_LOGIC_SPEED_CHANGE;
>> dw_pcie_wr_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, val);
>>
>> -#ifdef CONFIG_PCI_MSI
>> - dw_pcie_msi_chip.dev = pp->dev;
>> - dw_pci.msi_ctrl = &dw_pcie_msi_chip;
>> +#ifdef CONFIG_ARM
>> + /*
>> + * FIXME: we should really be able to use
>> + * of_pci_get_host_bridge_resources on arm32 as well,
>> + * but the conversion needs some more testing
>> + */
>> + if (global_io_offset < SZ_1M && pp->io_size > 0) {
>> + pci_ioremap_io(global_io_offset, pp->io_base);
>> + global_io_offset += SZ_64K;
>> + pci_add_resource_offset(&res, &pp->io,
>> + global_io_offset - pp->io_bus_addr);
>> + }
>> + pci_add_resource_offset(&res, &pp->mem,
>> + pp->mem.start - pp->mem_bus_addr);
>> + pci_add_resource(&res, &pp->busn);
>
> I don't think this #ifdef is necessary. In the spirit of 'the conversion
> needs some more testing', I removed it leaving just the below arm64 code.
>
> This worked on my Freescale i.MX6 Quad SABRE Lite Board, I went as far as
> scanning for wireless access points.
>
>
Hi James,
I think you are right. We can remove #ifdef as of_pci_get_host_bridge_resources
also manages mem, io and bus resources.
And just as Lorenzo said, if we want PCIe cards with IO bar work well,
pci_remap_iospace should be added after of_pci_get_host_bridge_resources to map
IO cpu address to PCI_IOBASE.
Thanks again for your test :)
Zhou
>> +#else
>> + ret = of_pci_get_host_bridge_resources(np, 0, 0xff, &res, &pp->io_base);
>
> of_pci_get_host_bridge_resources expects &pp->io_base to be a
> resource_size_t*, but &io_base is u64*. This generates a warning on arm
> with the above change. Changing the the type in
> drivers/pci/host/pcie-designware.h fixes this.
>
>
> Thanks,
>
> James
>
>> + if (ret)
>> + return ret;
>> +#endif
>> +
>> + bus = pci_create_root_bus(pp->dev, pp->root_bus_nr, &dw_pcie_ops,
>> + pp, &res);
>> + if (!bus)
>> + return -ENOMEM;
>> +
>> +#ifdef CONFIG_GENERIC_MSI_IRQ_DOMAIN
>> + bus->msi = container_of(&pp->irq_domain, struct msi_controller, domain);
>> +#else
>> + bus->msi = &dw_pcie_msi_chip;
>> #endif
>>
>> - dw_pci.nr_controllers = 1;
>> - dw_pci.private_data = (void **)&pp;
>> + pci_scan_child_bus(bus);
>> + if (pp->ops->scan_bus)
>> + pp->ops->scan_bus(pp);
>>
>> - pci_common_init_dev(pp->dev, &dw_pci);
>> +#ifdef CONFIG_ARM
>> + /* support old dtbs that incorrectly describe IRQs */
>> + pci_fixup_irqs(pci_common_swizzle, of_irq_parse_and_map_pci);
>> +#endif
>> +
>> + pci_assign_unassigned_bus_resources(bus);
>> + pci_bus_add_devices(bus);
>>
>> return 0;
>> }
>> @@ -653,7 +683,7 @@ static int dw_pcie_valid_config(struct pcie_port *pp,
>> static int dw_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where,
>> int size, u32 *val)
>> {
>> - struct pcie_port *pp = sys_to_pcie(bus->sysdata);
>> + struct pcie_port *pp = bus->sysdata;
>> int ret;
>>
>> if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0) {
>> @@ -677,7 +707,7 @@ static int dw_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where,
>> static int dw_pcie_wr_conf(struct pci_bus *bus, u32 devfn,
>> int where, int size, u32 val)
>> {
>> - struct pcie_port *pp = sys_to_pcie(bus->sysdata);
>> + struct pcie_port *pp = bus->sysdata;
>> int ret;
>>
>> if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0)
>> @@ -701,64 +731,6 @@ static struct pci_ops dw_pcie_ops = {
>> .write = dw_pcie_wr_conf,
>> };
>>
>> -static int dw_pcie_setup(int nr, struct pci_sys_data *sys)
>> -{
>> - struct pcie_port *pp;
>> -
>> - pp = sys_to_pcie(sys);
>> -
>> - if (global_io_offset < SZ_1M && pp->io_size > 0) {
>> - sys->io_offset = global_io_offset - pp->io_bus_addr;
>> - pci_ioremap_io(global_io_offset, pp->io_base);
>> - global_io_offset += SZ_64K;
>> - pci_add_resource_offset(&sys->resources, &pp->io,
>> - sys->io_offset);
>> - }
>> -
>> - sys->mem_offset = pp->mem.start - pp->mem_bus_addr;
>> - pci_add_resource_offset(&sys->resources, &pp->mem, sys->mem_offset);
>> - pci_add_resource(&sys->resources, &pp->busn);
>> -
>> - return 1;
>> -}
>> -
>> -static struct pci_bus *dw_pcie_scan_bus(int nr, struct pci_sys_data *sys)
>> -{
>> - struct pci_bus *bus;
>> - struct pcie_port *pp = sys_to_pcie(sys);
>> -
>> - pp->root_bus_nr = sys->busnr;
>> - bus = pci_create_root_bus(pp->dev, sys->busnr,
>> - &dw_pcie_ops, sys, &sys->resources);
>> - if (!bus)
>> - return NULL;
>> -
>> - pci_scan_child_bus(bus);
>> -
>> - if (bus && pp->ops->scan_bus)
>> - pp->ops->scan_bus(pp);
>> -
>> - return bus;
>> -}
>> -
>> -static int dw_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
>> -{
>> - struct pcie_port *pp = sys_to_pcie(dev->bus->sysdata);
>> - int irq;
>> -
>> - irq = of_irq_parse_and_map_pci(dev, slot, pin);
>> - if (!irq)
>> - irq = pp->irq;
>> -
>> - return irq;
>> -}
>> -
>> -static struct hw_pci dw_pci = {
>> - .setup = dw_pcie_setup,
>> - .scan = dw_pcie_scan_bus,
>> - .map_irq = dw_pcie_map_irq,
>> -};
>> -
>> void dw_pcie_setup_rc(struct pcie_port *pp)
>> {
>> u32 val;
>
>
> .
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2015-06-11 2:46 UTC|newest]
Thread overview: 59+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-06-03 8:35 [PATCH v2 0/4] PCI: hisi: Add PCIe host support for Hisilicon Soc Hip05 Zhou Wang
2015-06-03 8:35 ` Zhou Wang
2015-06-03 8:35 ` Zhou Wang
2015-06-03 8:35 ` [PATCH v2 1/4] ARM/PCI: remove align_resource callback in pcibios_align_resource Zhou Wang
2015-06-03 8:35 ` Zhou Wang
2015-06-03 8:35 ` Zhou Wang
2015-06-04 13:18 ` James Morse
2015-06-04 13:18 ` James Morse
2015-06-05 3:53 ` Zhou Wang
2015-06-05 3:53 ` Zhou Wang
2015-06-03 8:35 ` [PATCH v2 2/4] PCI: designware: Add ARM64 support Zhou Wang
2015-06-03 8:35 ` Zhou Wang
2015-06-03 8:35 ` Zhou Wang
2015-06-04 13:19 ` James Morse
2015-06-04 13:19 ` James Morse
2015-06-05 8:11 ` Zhou Wang
2015-06-05 8:11 ` Zhou Wang
2015-06-09 11:15 ` Lorenzo Pieralisi
2015-06-09 11:15 ` Lorenzo Pieralisi
2015-06-09 11:15 ` Lorenzo Pieralisi
2015-06-10 13:35 ` Gabriele Paoloni
2015-06-10 13:35 ` Gabriele Paoloni
2015-06-10 13:35 ` Gabriele Paoloni
2015-06-11 5:44 ` Zhou Wang
2015-06-11 5:44 ` Zhou Wang
2015-06-11 14:32 ` Gabriele Paoloni
2015-06-11 14:32 ` Gabriele Paoloni
2015-06-16 11:30 ` Zhou Wang
2015-06-16 11:30 ` Zhou Wang
2015-06-16 14:14 ` Gabriele Paoloni
2015-06-16 14:14 ` Gabriele Paoloni
2015-07-13 10:58 ` Lorenzo Pieralisi
2015-07-13 10:58 ` Lorenzo Pieralisi
2015-07-13 11:45 ` Zhou Wang
2015-07-13 11:45 ` Zhou Wang
2015-07-13 14:17 ` Lorenzo Pieralisi
2015-07-13 14:17 ` Lorenzo Pieralisi
2015-07-17 10:45 ` Gabriele Paoloni
2015-07-17 10:45 ` Gabriele Paoloni
2015-06-11 2:51 ` Zhou Wang
2015-06-11 2:51 ` Zhou Wang
2015-06-11 2:44 ` Zhou Wang [this message]
2015-06-11 2:44 ` Zhou Wang
2015-06-11 2:44 ` Zhou Wang
2015-06-14 19:18 ` Pratyush Anand
2015-06-14 19:18 ` Pratyush Anand
2015-06-16 10:14 ` Zhou Wang
2015-06-16 10:14 ` Zhou Wang
2015-06-16 10:14 ` Zhou Wang
2015-06-03 8:35 ` [PATCH v2 3/4] PCI: hisi: Add PCIe host support for Hisilicon Soc Hip05 Zhou Wang
2015-06-03 8:35 ` Zhou Wang
2015-06-03 8:35 ` Zhou Wang
2015-06-04 13:23 ` James Morse
2015-06-04 13:23 ` James Morse
2015-06-05 8:13 ` Zhou Wang
2015-06-05 8:13 ` Zhou Wang
2015-06-03 8:35 ` [PATCH v2 4/4] Documentation: DT: Add Hisilicon PCIe host binding Zhou Wang
2015-06-03 8:35 ` Zhou Wang
2015-06-03 8:35 ` Zhou Wang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5578F625.1090305@hisilicon.com \
--to=wangzhou1@hisilicon.com \
--cc=Liviu.Dudau@arm.com \
--cc=arnd@arndb.de \
--cc=bhelgaas@google.com \
--cc=devicetree@vger.kernel.org \
--cc=fabrice.gasnier@st.com \
--cc=gabriele.paoloni@huawei.com \
--cc=james.morse@arm.com \
--cc=jg1.han@samsung.com \
--cc=liguozhu@hisilicon.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-pci@vger.kernel.org \
--cc=pratyush.anand@gmail.com \
--cc=qiuzhenfa@hisilicon.com \
--cc=yuanzhichang@hisilicon.com \
--cc=zhangjukuo@huawei.com \
--cc=zhudacai@hisilicon.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.